Ubiquiti AF4X Dual Channel OFDM MIMO Point to Point Device User Manual airFiber X User Guide

Ubiquiti Networks, Inc. Dual Channel OFDM MIMO Point to Point Device airFiber X User Guide

Users Manual pt 5

55Appendix E: WarrantyairFiber X User GuideUbiquiti Networks, Inc.Appendix E: WarrantyLimited WarrantyUBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS’ sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term. Warranty ConditionsThe above warranty does not apply if the Product:(I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks’ authorized representatives, or as approved by Ubiquiti Networks in writing;(II) has been painted, rebranded or physically modified in any way;(III) has been damaged due to errors or defects in cabling;(IV) has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident;(V) has been damaged or impaired as a result of using third party firmware;(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or(VII) has not been received by Ubiquiti within 30 days of issuance of the RMA.In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed.WARNING: Failure to properly ground your airFiber units will void your warranty. (Please follow the instructions on “Install a Ground Wire” on page 5 for installation of the ground wires.)ReturnsNo Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS’ facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal. Information on the RMA process and obtaining an RMA number can be found at: www.ubnt.com/support/warranty.DisclaimerEXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyer’s selection of products (including the Products) for buyer’s application and/or failure of products (including the Products) to meet government or regulatory requirements.
56Appendix E: Warranty airFiber X User GuideUbiquiti Networks, Inc.Limitation of LiabilityEXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NoteSome countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products.
57Appendix F: Compliance InformationairFiber X User GuideUbiquiti Networks, Inc.Appendix F: Compliance InformationInstaller Compliance ResponsibilityDevices must be professionally installed and it is the professional installer’s responsibility to make sure the device is operated within local country regulatory requirements.FCCairFiber AF-2XChanges or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.This radio transmitter (FCC: SWX-AF2X) has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.• Dish antenna, gain: 6 dBi• Dish antenna, gain: 24 dBiairFiber AF-3XChanges or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.This radio transmitter (FCC: SWX-AF3X) has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.• Dish antenna, gain: 12 dBi• Dish antenna, gain: 26 dBi• Dish antenna, gain: 29 dBi
58Appendix F: Compliance Information airFiber X User GuideUbiquiti Networks, Inc.airFiber AF-4XChanges or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.airFiber AF-5XChanges or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.This radio transmitter (FCC: SWX-AF5X) has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.• Dish antenna, gain: 23 dBi• Dish antenna, gain: 30 dBi• Dish antenna, gain: 34 dBiDFS Regulatory RegionsOperation in DFS regulatory regions requires an antenna with minimum gain of 23 dBi.
59Appendix F: Compliance InformationairFiber X User GuideUbiquiti Networks, Inc.Industry CanadaairFiber AF-2XCAN ICES-3(B)/NMB-3(B)To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device.This radio transmitter (IC: 6545A-AF2X) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.• Dish antenna, gain: 6 dBi• Dish antenna, gain: 24 dBiCAN ICES-3(B)/NMB-3(B)Pour réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie. Cet appareil est conforme à la norme RSS Industrie Canada exempts de licence norme(s). Son fonctionnement est soumis aux deux conditions suivantes:1. Cet appareil ne peut pas provoquer d’interférences et 2. Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.Cet émetteur radio (IC: 6545A-AF2X) a été approuvée par Industrie Canada pour l’exploitation avec l’antenne types énumérés ci-dessous avec le gain maximal admissible et requis l’impédance de l’antenne pour chaque type d’antenne indiqué. Types d’antenne non inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce type, sont strictement interdits pour une utilisation avec cet appareil. Immédiatement suite à la remarque, le fabricant doit fournir une liste de tous les types d’antenne approuvé pour une utilisation avec l’émetteur, ce qui indique le gain maximal d’antenne permis (en dBi) et requis d’impédance pour chacun.• Antenne parabolique, gain: 6 dBi• Antenne parabolique, gain: 24 dBiairFiber AF-3XCAN ICES-3(B)/NMB-3(B)To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device.This radio transmitter (IC: 6545A-AF3X) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.• Dish antenna, gain: 12 dBi• Dish antenna, gain: 26 dBi• Dish antenna, gain: 29 dBiCAN ICES-3(B)/NMB-3(B)Pour réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie. Cet appareil est conforme à la norme RSS Industrie Canada exempts de licence norme(s). Son fonctionnement est soumis aux deux conditions suivantes:1. Cet appareil ne peut pas provoquer d’interférences et 2. Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.Cet émetteur radio (IC: 6545A-AF3X) a été approuvée par Industrie Canada pour l’exploitation avec l’antenne types énumérés ci-dessous avec le gain maximal admissible et requis l’impédance de l’antenne pour chaque type d’antenne indiqué. Types d’antenne non inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce type, sont strictement interdits pour une utilisation avec cet appareil. Immédiatement suite à la remarque, le fabricant doit fournir une liste de tous les types d’antenne approuvé pour une utilisation avec l’émetteur, ce qui indique le gain maximal d’antenne permis (en dBi) et requis d’impédance pour chacun.• Antenne parabolique, gain: 12 dBi• Antenne parabolique, gain: 26 dBi• Antenne parabolique, gain: 29 dBi
60Appendix F: Compliance Information airFiber X User GuideUbiquiti Networks, Inc.airFiber AF-4XCAN ICES-3(B)/NMB-3(B)To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device.CAN ICES-3(B)/NMB-3(B)Pour réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie. Cet appareil est conforme à la norme RSS Industrie Canada exempts de licence norme(s). Son fonctionnement est soumis aux deux conditions suivantes:1. Cet appareil ne peut pas provoquer d’interférences et 2. Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.airFiber AF-5XCAN ICES-3(B)/NMB-3(B)To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device.This radio transmitter (IC: 6545A-AF5X) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.• Dish antenna, gain: 23 dBi• Dish antenna, gain: 30 dBi• Dish antenna, gain: 34 dBiCAN ICES-3(B)/NMB-3(B)Pour réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie. Cet appareil est conforme à la norme RSS Industrie Canada exempts de licence norme(s). Son fonctionnement est soumis aux deux conditions suivantes:1. Cet appareil ne peut pas provoquer d’interférences et 2. Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.Cet émetteur radio (IC: 6545A-AF5X) a été approuvée par Industrie Canada pour l’exploitation avec l’antenne types énumérés ci-dessous avec le gain maximal admissible et requis l’impédance de l’antenne pour chaque type d’antenne indiqué. Types d’antenne non inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce type, sont strictement interdits pour une utilisation avec cet appareil. Immédiatement suite à la remarque, le fabricant doit fournir une liste de tous les types d’antenne approuvé pour une utilisation avec l’émetteur, ce qui indique le gain maximal d’antenne permis (en dBi) et requis d’impédance pour chacun.• Antenne parabolique, gain: 23 dBi• Antenne parabolique, gain: 30 dBi• Antenne parabolique, gain: 34 dBi
61Appendix F: Compliance InformationairFiber X User GuideUbiquiti Networks, Inc.RF Exposure WarningairFiber AF-2XThe antennas used for this transmitter must be installed to provide a separation distance of at least 126 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter.Les antennes utilisées pour ce transmetteur doivent être installé en considérant une distance de séparation de toute personnes d’au moins 126cm et ne doivent pas être localisé ou utilisé en conflit avec tout autre antenne ou transmetteur.airFiber AF-3XThe antennas used for this transmitter must be installed to provide a separation distance of at least 364 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter.Les antennes utilisées pour ce transmetteur doivent être installé en considérant une distance de séparation de toute personnes d’au moins 364cm et ne doivent pas être localisé ou utilisé en conflit avec tout autre antenne ou transmetteur.airFiber AF-4XThe radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during the normal operation is minimized. In order to avoid the possibility of exceeding the FCC radio frequency exposure limit, human proximity to the antenna should be more than 180 cm.La puissance de sortie rayonnée de cet appareil est inférieure aux limites d’exposition de radio de fréquence FCC. Néanmoins, le dispositif doit être utilisé de telle manière que le potentiel pour le contact humain pendant l’utilisation normale soit minimisé. Afin d’éviter la possibilité de dépasser la limite d’exposition de fréquence radio de la FCC, la proximité humaine à l’antenne devrait être plus que 180 cm.airFiber AF-5XThe antennas used for this transmitter must be installed to provide a separation distance of at least 126 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter.Les antennes utilisées pour ce transmetteur doivent être installé en considérant une distance de séparation de toute personnes d’au moins 126cm et ne doivent pas être localisé ou utilisé en conflit avec tout autre antenne ou transmetteur.Australia and New ZealandairFiber AF-2XWarning: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.airFiber AF-3XWarning: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.airFiber AF-4XWarning: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.airFiber AF-5XWarning: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
62Appendix F: Compliance Information airFiber X User GuideUbiquiti Networks, Inc.CE MarkingairFiber AF-2XCE marking on this product represents the product is in compliance with all directives that are applicable to it.airFiber AF-3XCE marking on this product represents the product is in compliance with all directives that are applicable to it.airFiber AF-4XCE marking on this product represents the product is in compliance with all directives that are applicable to it.airFiber AF-5XCE marking on this product represents the product is in compliance with all directives that are applicable to it.Alert sign! follows CE markingAlert sign must be indicated if a restriction on use applied to the product and it must follow the CE marking.airFiber AF-4X ComplianceThe user is responsible for obtaining all licenses that are required by the local country in which the product will be operated, and all such licenses must be obtained prior to operation in the particular country. For information on licenses required by your country as well as conditions of use for the 4 GHz band, contact your appropriate national authority. 4.9 GHz Band Devices (FCC and Industry Canada)The 4.9 GHz band is a licensed band allocated to public safety services. State and local government entities that provide public safety services are eligible to apply for 4.9GHz licenses. For additional information, refer to FCC or Industry Canada regulations.
63Appendix F: Compliance InformationairFiber X User GuideUbiquiti Networks, Inc.Frequency Ranges and Power Levels per Country/RegionairFiber AF-2XThe product can be operated in the countries and regions listed in the following table, within the stated frequency ranges and output power (EIRP)limits.Each country has its own power level and frequency regulations. To ensure the product operates under the necessary regulatory compliance rules, the country where the device will be used must be selected during installation. The frequency settings and output power (EIRP) limits will be tuned according to the regulations of the selected country/region:Country/Region Frequency Range (Band Edges in MHz) Max. EIRP (dBm)Argentina 2400-2483 36Australia 2400-2483 36Bahrain 2400-2483 36Brazil 2400-2483 36Canada 2400-2483 36*Chile 2400-2483 36China 2400-2483 36Colombia 2400-2483 36Ecuador 2400-2483 36Ghana 2400-2483 36Guam (U.S. territory) 2400-2483 36*Hong Kong 2400-2483 36Indonesia 2400-2483 36India 2400-2483 36Kenya 2400-2483 36Korea Republic 2400-2483 36Kyrgyzstan 2400-2483 Not applicableMalaysia 2400-2483 36Mexico 2400-2483 36New Zealand 2400-2483 36Nigeria 2400-2483 36Peru 2400-2483 36Philippines 2400-2483 36Puerto Rico (U.S. territory) 2400-2483 36*Singapore 2400-2483 36South Africa 2400-2483 36Taiwan 2400-2483 36Tajikistan 2400-2483 Not applicableThailand 2400-2483 20Turkmenistan 2400-2483 Not applicableUganda 2400-2483 Not applicableUnited States 2400-2483 36*Uzbekistan 2400-2483 Not applicableVenezuela 2400-2483 36Virgin Islands (U.S. territory) 2400-2483 36*Vietnam 2400-2483 36* A higher EIRP is possible based on FCC Part 15 requirements of reduction of conducted power by 1dBm per 3dBi increase of antenna gain beyond 6dBi.
64Appendix F: Compliance Information airFiber X User GuideUbiquiti Networks, Inc.airFiber AF-3XThe product can be operated in the countries and regions listed in the following table, within the stated frequency ranges and output power (EIRP)limits.Each country has its own power level and frequency regulations. To ensure the product operates under the necessary regulatory compliance rules, the country where the device will be used must be selected during installation. The frequency settings and output power (EIRP) limits will be tuned according to the regulations of the selected country/region:Country/Region Frequency Range (Band Edges in MHz) Max. EIRP (dBm)Austria 3410-3900 66Belgium 3410-3900 66Bulgaria 3410-3900 66Canada 3450-36503650-37005744Croatia 3410-3900 66Cyprus 3410-3900 66Czech Republic 3410-3900 66Denmark 3410-3900 66Estonia 3410-3900 66Finland 3410-3900 66France 3410-3900 66Germany 3410-3900 66Greece 3410-3900 66Guam (U.S. territory) 3650-3700 44Hungary 3410-3900 66Ireland 3410-3900 66Italy 3410-3900 66Latvia 3410-3900 66Lithuania 3410-3900 66Malta 3410-3900 66Netherlands 3410-3900 66Poland 3410-3900 66Portugal 3410-3900 66Puerto Rico (U.S. territory) 3650-3700 44Romania 3410-3900 66Slovakia 3410-3900 66Spain 3410-3900 66Sweden 3410-3900 66United Kingdom 3410-3900 66United States 3650-3700 44Virgin Islands (U.S. territory) 3650-3700 44
65Appendix F: Compliance InformationairFiber X User GuideUbiquiti Networks, Inc.airFiber AF-4XThe product can be operated in the countries and regions listed in the following table, within the stated frequency ranges and output power (EIRP)limits. Users are responsible to comply with all local regulatory rules and requirements beyond what is stated in the table.Each country has its own power level and frequency regulations. To ensure the product operates under the necessary regulatory compliance rules, the country where the device will be used must be selected during installation. The frequency settings and output power (EIRP) limits will be tuned according to the regulations of the selected country/region:Country/Region Frequency Range (Band Edges in MHz) Max. EIRP (dBm)Austria 3410-3900 55Belgium 3410-3900 55Bulgaria 3410-3900 55Canada 4940-4990 55Croatia 3410-3900 55Cyprus 3410-3900 55Czech Republic 3410-3900 55Denmark 3410-3900 55Estonia 3410-3900 55Finland 3410-3900 55France 3410-3900 55Germany 3410-3900 55Greece 3410-3900 55Guam (U.S. territory) 4940-4990 55Hungary 3410-3900 55Ireland 3410-3900 55Italy 3410-3900 55Latvia 3410-3900 55Lithuania 3410-3900 55Malta 3410-3900 55Netherlands 3410-3900 55Poland 3410-3900 55Portugal 3410-3900 55Puerto Rico (U.S. territory) 4940-4990 55Romania 3410-3900 55Slovakia 3410-3900 55Spain 3410-3900 55Sweden 3410-3900 55United Kingdom 3410-3900 55United States 4940-4990 55Virgin Islands (U.S. territory) 4940-4990 55
airFiber X User GuideAppendix F: Compliance InformationUbiquiti Networks, Inc.66airFiber AF-5XThe product can be operated in the countries and regions listed in the following table, within the stated frequency ranges and output power (EIRP)limits.Each country has its own power level and frequency regulations. To ensure the product operates under the necessary regulatory compliance rules, the country where the device will be used must be selected during installation. The frequency settings and output power (EIRP) limits will be tuned according to the regulations of the selected country/region:Country/Region5.1 GHz 5.2 GHz 5.4 GHz 5.8 GHzFrequency Range (Band Edges in MHz)Max. EIRP (dBm)Frequency Range (Band Edges in MHz)Max. EIRP (dBm)Frequency Range (Band Edges in MHz)Max. EIRP (dBm)Frequency Range (Band Edges in MHz)Max. EIRP (dBm)Argentina 5150-5250 49 5470-5725 30 5725-5850 36Australia 5470-5600, 5650-5725 30 5725-5855 36Bahrain 5735-5835 20Barbados 5725-5850 36Belize 5735-5835 30Bolivia 5735-5835 30Brazil 5470-5725 30 5725-5850 53Brunei Darussalam 5735-5835 20Canada 5250-5350 30 5470-5600, 5650-5725 30 5725-5850 60Chile 5250-5350 30 5735-5835 20China 5735-5835 30Colombia 5250-5350 30 5735-5835 30Costa Rica 5735-5835 30Denmark 5470-5725 30 5725-5795, 5815-5850 36Dominican Republic 5735-5835 30Ecuador 5150-5250 49 5250-5350 30 5735-5835 30El Salvador 5735-5835 30Finland 5470-5725 30 5725-5795, 5815-5850 36Germany 5470-5725 30 5755-5875 36Greece 5470-5725 30 5725-5795 36Grenada 5470-5725 30 5725-5850 36Guatemala 5735-5835 30Honduras 5470-5725 30 5725-5850 36Hong Kong 5250-5350 30 5470-5725 30 5725-5850 36Iceland 5470-5725 30 5725-5875 36India 5825-5875 36Iraq 5735-5835 36Ireland 5470-5725 30 5725-5875 33Italy 5470-5725 30Jamaica 5470-5725 30 5725-5850 36
67Appendix F: Compliance InformationairFiber X User GuideUbiquiti Networks, Inc.Country/Region5.1 GHz 5.2 GHz 5.4 GHz 5.8 GHzFrequency Range (Band Edges in MHz)Max. EIRP (dBm)Frequency Range (Band Edges in MHz)Max. EIRP (dBm)Frequency Range (Band Edges in MHz)Max. EIRP (dBm)Frequency Range (Band Edges in MHz)Max. EIRP (dBm)Kenya 5250-5350 30 5735-5835 30Korea Republic 5490-5710 30 5735-5815 30Lebanon 5735-5835 30Liechtenstein 5470-5725 30 5725-5795, 5815-5875 36Macau 5725-5850 36Malaysia 5150-5250 49 5250-5350 30 5735-5835 30Mexico 5735-5835 30Morocco 5735-5835 20Nepal 5735-5835 30New Zealand 5470-5725 30 5725-5850 53Norway 5470-5725 30 5725-5795, 5815-5850 53Oman 5470-5725 30 5725-5850 36Pakistan 5735-5835 30Panama 5735-5835 30Papua New Guinea 5735-5835 30Peru 5150-5250 49 5250-5350 30 5470-5725 30 5725-5850 36Philippines 5150-5250 49 5250-5350 30 5470-5725 30 5725-5850 36Portugal 5470-5725 30 5725-5875 36Puerto Rico (U.S. territory) 5250-5350 30 5470-5600, 5650-5725 30 5725-5850 60Qatar 5735-5835 30Russia 5150-5350 43 5470-5650 23 5650-5950 53Singapore 5735-5835 30South Africa 5470-5725 30 5725-5850 60Spain 5470-5725 30 5725-5795, 5815-5855 36Switzerland 5470-5725 30 5725-5795, 5815-5855 36Taiwan 5250-5350 30 5490-5710 30 5735-5815 30Thailand 5250-5350 30 5470-5725 30 5725-5850 36Trinidad And Tobago 5470-5725 30 5725-5850 36United Kingdom 5470-5725 30 5725-5790, 5815-5850 36United States 5150-5250 49 5250-5350 30 5470-5600, 5650-5725 30 5725-5850 60Uruguay 5470-5725 30 5725-5850 36Uzbekistan 5470-5725 30 5725-5850 36Venezuela 5150-5250 49 5250-5350 30 5735-5835 30
68Appendix F: Compliance Information airFiber X User GuideUbiquiti Networks, Inc.The following table lists the maximum transmit output power (EIRP) for the 5.1 GHz band.5.1 GHz Band Maximum Transmit Output Power (EIRP) in dBmChannel Bandwidth Frequency Range (Band Edges in MHz)10 MHz5155-5175 395166-5186 445177-5250 4920 MHz5156-5180 375161-5185 395166-5209 445190-5250 4930 MHz5155-5192 375163-5202 395173-5211 445182-5250 4940 MHz5155-5204 375165-5219 395180-5228 445189-5250 4950 MHz5155-5214 375165-5233 395184-5242 445193-5250 49
69Appendix F: Compliance InformationairFiber X User GuideUbiquiti Networks, Inc.RoHS/WEEE Compliance StatementEnglishEuropean Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.DeutschDie Europäische Richtlinie 2012/19/EU verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist , nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto.FrançaisLa directive européenne 2012/19/UE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.ItalianoLa direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.
70Appendix F: Compliance Information airFiber X User GuideUbiquiti Networks, Inc.
71Appendix G: Declaration of ConformityairFiber X User GuideUbiquiti Networks, Inc.Appendix G: Declaration of ConformityČesky [Czech]UBIQUITI NETWORKS tímto prohlašuje, že toto UBIQUITI NETWORKS zařízení, je ve shod se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.Dansk [Danish]Hermed, UBIQUITI NETWORKS, erklærer at denne UBIQUITI NETWORKS enhed, er i overensstemmelse med de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.Nederlands [Dutch]Hierbij verklaart UBIQUITI NETWORKS, dat deze UBIQUITI NETWORKS apparaat, in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EC.EnglishHereby, UBIQUITI NETWORKS, declares that this UBIQUITI NETWORKS device, is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Eesti [Estonian]Käesolevaga UBIQUITI NETWORKS kinnitab, et antud UBIQUITI NETWORKS seade, on vastavus olulistele nõuetele ja teistele asjakohastele sätetele direktiivi 1999/5/EÜ.Suomi [Finnish]Täten UBIQUITI NETWORKS vakuuttaa, että tämä UBIQUITI NETWORKS laite, on yhdenmukainen olennaisten vaatimusten ja muiden sitä koskevien direktiivin 1999/5/EY.Français [French]Par la présente UBIQUITI NETWORKS déclare que l’appareil UBIQUITI NETWORKS, est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.Deutsch [German]Hiermit erklärt UBIQUITI NETWORKS, dass sich dieses UBIQUITI NETWORKS Gerät, in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet.Ελληνική [Greek]Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η συσκευή UBIQUITI NETWORKS, είναι σε συμμόρφωση με τις βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 1995/5/ΕΚ.Magyar [Hungarian]Ezennel UBIQUITI NETWORKS kijelenti, hogy ez a UBIQUITI NETWORKS készülék megfelel az alapvető követelményeknek és más vonatkozó 1999/5/EK irányelv rendelkezéseit.Íslenska [Icelandic]Hér, UBIQUITI NETWORKS, því yfir að þetta UBIQUITI NETWORKS tæki er í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipun 1999/5/EC.Italiano [Italian]Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo UBIQUITI NETWORKS, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti della direttiva 1999/5/CE.Latviski [Latvian]Ar šo, UBIQUITI NETWORKS, deklarē, ka UBIQUITI NETWORKS ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvā 1999/5/EK.Lietuviškai [Lithuanian]UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.Malti [Maltese]Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz UBIQUITI NETWORKS huwa konformi mar-rekwiżiti essenzjali u dispożizzjonijiet rilevanti oħrajn ta ‘Direttiva 1999/5/EC.Norsk [Norwegian]Herved UBIQUITI NETWORKS, erklærer at denne UBIQUITI NETWORKS enheten, er i samsvar med de grunnleggende kravene og andre relevante bestemmelser i direktiv 1999/5/EF.Slovensky [Slovak]Týmto UBIQUITI NETWORKS, prehlasuje, že toto UBIQUITI NETWORKS zariadenie, je v súlade so základnými požiadavkami a ďalšími relevantnými ustanoveniami smernice 1999/5/ES.Svenska [Swedish]Härmed UBIQUITI NETWORKS, intygar att denna UBIQUITI NETWORKS enhet är i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.Español [Spanish]Por medio de la presente UBIQUITI NETWORKS declara que este dispositivo UBIQUITI NETWORKS, cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.Polski [Polish]Niniejszym, Ubiquiti Networks, oświadcza, że urządzenie UBIQUITI NETWORKS, jest zgodny z zasadniczymi wymaganiami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.Português [Portuguese]UBIQUITI NETWORKS declara que este dispositivo UBIQUITI NETWORKS, está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.Română [Romanian]Prin prezenta, UBIQUITI NETWORKS declară că acest dispozitiv UBIQUITI NETWORKS este în conformitate cu cerințele esențiale și alte prevederi relevante ale Directivei 1999/5/CE.
72Appendix G: Declaration of Conformity airFiber X User GuideUbiquiti Networks, Inc.
73Appendix H: Contact InformationairFiber X User GuideUbiquiti Networks, Inc.Appendix H: Contact InformationUbiquiti Networks SupportUbiquiti Support Engineers are located around the world and are dedicated to helping customers resolve software, hardware compatibility, or field issues as quickly as possible. We strive to respond to support inquiries within a 24-hour period.Ubiquiti Networks, Inc. 2580 Orchard Parkway San Jose, CA 95131 www.ubnt.comOnline ResourcesSupport: ubnt.link/airFiber-SupportCommunity: community.ubnt.com/airfiberDownloads: downloads.ubnt.com/airfiberAI040116
www.ubnt.com©2016 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airFiber, airOS, RocketDish, TOUGHCable, and xRT are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners.

Navigation menu