Ubiquiti AF4X Dual Channel OFDM MIMO Point to Point Device User Manual airFiber X User Guide

Download:
Mirror Download [FCC.gov]
Document ID	2963302
Application ID	oJYQS9BBCwKFnS50QM7JFA==
Document Description	Users Manual pt 5
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	100.52kB (1256488 bits)
Date Submitted	2016-04-07 00:00:00
Date Available	2016-10-04 00:00:00
Creation Date	2016-04-19 17:15:24
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2016-04-19 17:15:25
Document Title	airFiber X User Guide
Document Creator	Adobe InDesign CC 2015 (Macintosh)
Document Author:	A Imaoka

airFiber X User Guide
Appendix E: Warranty
Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”)
warrants that the product(s) furnished hereunder (the
“Product(s)”) shall be free from defects in material and
workmanship for a period of one (1) year from the date
of shipment by UBIQUITI NETWORKS under normal use
and operation. UBIQUITI NETWORKS’ sole and exclusive
obligation and liability under the foregoing warranty
shall be for UBIQUITI NETWORKS, at its discretion, to
repair or replace any Product that fails to conform to the
above warranty during the above warranty period. The
expense of removal and reinstallation of any Product is
not included in this warranty. The warranty period of any
repaired or replaced Product shall not extend beyond its
original term.
Warranty Conditions
The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition
made thereto, except by Ubiquiti Networks, or
Ubiquiti Networks’ authorized representatives, or as
approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in
any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence,
abnormal physical, electromagnetic or electrical
stress, including lightning strikes, or accident;
(V) has been damaged or impaired as a result of using
third party firmware;
(VI) has no original Ubiquiti MAC label, or is missing any
other original Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of
issuance of the RMA.
In addition, the above warranty shall apply only if: the
product has been properly installed and used at all times
in accordance, and in all material respects, with the
applicable Product documentation; all Ethernet cabling
runs use CAT5 (or above), and for outdoor installations,
shielded Ethernet cabling is used, and for indoor
installations, indoor cabling requirements are followed.
WARNING: Failure to properly ground your
airFiber units will void your warranty. (Please
follow the instructions on “Install a Ground Wire”
on page 5 for installation of the ground wires.)
Ubiquiti Networks, Inc.
Appendix E: Warranty
Returns
No Products will be accepted for replacement or repair
without obtaining a Return Materials Authorization (RMA)
number from UBIQUITI NETWORKS during the warranty
period, and the Products being received at UBIQUITI
NETWORKS’ facility freight prepaid in accordance with the
RMA process of UBIQUITI NETWORKS. Products returned
without an RMA number will not be processed and will be
returned freight collect or subject to disposal. Information
on the RMA process and obtaining an RMA number can be
found at: www.ubnt.com/support/warranty.
Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED
HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS
AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND
HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE
NO OTHER REPRESENTATION OR WARRANTY OF ANY
KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING,
BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES,
OR WARRANTIES OF MERCHANTABILITY, ACCURACY,
QUALITY OF SERVICE OR RESULTS, AVAILABILITY,
SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET
ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND
NON-INFRINGEMENT AND ANY WARRANTIES ARISING
FROM ANY COURSE OF DEALING, USAGE OR TRADE
PRACTICE IN CONNECTION WITH SUCH PRODUCTS
AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER
UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS
CONTROL BUYER’S EQUIPMENT OR THE TRANSFER OF
DATA OVER COMMUNICATIONS FACILITIES, INCLUDING
THE INTERNET, AND THAT THE PRODUCTS AND SERVICES
MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS,
DELAYS, CANCELLATIONS AND OTHER PROBLEMS
INHERENT IN THE USE OF COMMUNICATIONS FACILITIES.
UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR
THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY
INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY
FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET
LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE
FOREGOING. In addition, UBIQUITI NETWORKS does not
warrant that the operation of the Products will be errorfree or that operation will be uninterrupted. In no event
shall UBIQUITI NETWORKS be responsible for damages
or claims of any nature or description relating to system
performance, including coverage, buyer’s selection of
products (including the Products) for buyer’s application
and/or failure of products (including the Products) to meet
government or regulatory requirements.
55
Appendix E: Warranty
airFiber X User Guide
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO
EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR
SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL,
CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST
PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING
OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF
USE OF THE PRODUCT, WHETHER BASED IN WARRANTY,
CONTRACT, TORT OR OTHER LEGAL THEORY, AND
WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
Note
Some countries, states and provinces do not allow
exclusions of implied warranties or conditions, so the
above exclusion may not apply to you. You may have
other rights that vary from country to country, state to
state, or province to province. Some countries, states
and provinces do not allow the exclusion or limitation of
liability for incidental or consequential damages, so the
above limitation may not apply to you. EXCEPT TO THE
EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY
TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND
ARE IN ADDITION TO, THE MANDATORY STATUTORY
RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE
(EMBEDDED IN THE PRODUCT) TO YOU. The United
Nations Convention on Contracts for the International Sale
of Goods shall not apply to any transactions regarding the
sale of the Products.
56
Ubiquiti Networks, Inc.
airFiber X User Guide
Appendix F: Compliance Information
Appendix F: Compliance
Information
airFiber AF-3X
Installer Compliance Responsibility
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions.
Devices must be professionally installed and it is the
professional installer’s responsibility to make sure the
device is operated within local country regulatory
requirements.
FCC
airFiber AF-2X
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
This radio transmitter (FCC: SWX-AF3X) has been approved
by FCC to operate with the antenna types listed below
with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna
types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly
prohibited for use with this device.
• Dish antenna, gain: 12 dBi
• Dish antenna, gain: 26 dBi
• Dish antenna, gain: 29 dBi
This radio transmitter (FCC: SWX-AF2X) has been approved
by FCC to operate with the antenna types listed below
with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna
types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly
prohibited for use with this device.
• Dish antenna, gain: 6 dBi
• Dish antenna, gain: 24 dBi
Ubiquiti Networks, Inc.
57
Appendix F: Compliance Information
airFiber X User Guide
airFiber AF-4X
airFiber AF-5X
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions.
1. This device may not cause harmful interference, and
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
This radio transmitter (FCC: SWX-AF5X) has been approved
by FCC to operate with the antenna types listed below
with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna
types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly
prohibited for use with this device.
• Dish antenna, gain: 23 dBi
• Dish antenna, gain: 30 dBi
• Dish antenna, gain: 34 dBi
DFS Regulatory Regions
Operation in DFS regulatory regions requires an antenna
with minimum gain of 23 dBi.
58
Ubiquiti Networks, Inc.
airFiber X User Guide
Appendix F: Compliance Information
Industry Canada
airFiber AF-3X
airFiber AF-2X
CAN ICES-3(B)/NMB-3(B)
CAN ICES-3(B)/NMB-3(B)
To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more
than that permitted for successful communication.
To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more
than that permitted for successful communication.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
This radio transmitter (IC: 6545A-AF2X) has been approved
by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and
required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having
a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
• Dish antenna, gain: 6 dBi
• Dish antenna, gain: 24 dBi
CAN ICES-3(B)/NMB-3(B)
Pour réduire le risque d’interférence aux autres utilisateurs,
le type d’antenne et son gain doivent être choisies de
façon que la puissance isotrope rayonnée équivalente
(PIRE) ne dépasse pas ce qui est nécessaire pour une
communication réussie.
Cet appareil est conforme à la norme RSS Industrie Canada
exempts de licence norme(s). Son fonctionnement est
soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas provoquer d’interférences et
2. Cet appareil doit accepter toute interférence, y compris
les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
Cet émetteur radio (IC: 6545A-AF2X) a été approuvée par
Industrie Canada pour l’exploitation avec l’antenne types
énumérés ci-dessous avec le gain maximal admissible
et requis l’impédance de l’antenne pour chaque type
d’antenne indiqué. Types d’antenne non inclus dans cette
liste, ayant un gain supérieur au gain maximal indiqué
pour ce type, sont strictement interdits pour une utilisation
avec cet appareil. Immédiatement suite à la remarque, le
fabricant doit fournir une liste de tous les types d’antenne
approuvé pour une utilisation avec l’émetteur, ce qui
indique le gain maximal d’antenne permis (en dBi) et
requis d’impédance pour chacun.
• Antenne parabolique, gain: 6 dBi
• Antenne parabolique, gain: 24 dBi
Ubiquiti Networks, Inc.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
This radio transmitter (IC: 6545A-AF3X) has been approved
by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and
required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having
a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
• Dish antenna, gain: 12 dBi
• Dish antenna, gain: 26 dBi
• Dish antenna, gain: 29 dBi
CAN ICES-3(B)/NMB-3(B)
Pour réduire le risque d’interférence aux autres utilisateurs,
le type d’antenne et son gain doivent être choisies de
façon que la puissance isotrope rayonnée équivalente
(PIRE) ne dépasse pas ce qui est nécessaire pour une
communication réussie.
Cet appareil est conforme à la norme RSS Industrie Canada
exempts de licence norme(s). Son fonctionnement est
soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas provoquer d’interférences et
2. Cet appareil doit accepter toute interférence, y compris
les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
Cet émetteur radio (IC: 6545A-AF3X) a été approuvée par
Industrie Canada pour l’exploitation avec l’antenne types
énumérés ci-dessous avec le gain maximal admissible
et requis l’impédance de l’antenne pour chaque type
d’antenne indiqué. Types d’antenne non inclus dans cette
liste, ayant un gain supérieur au gain maximal indiqué
pour ce type, sont strictement interdits pour une utilisation
avec cet appareil. Immédiatement suite à la remarque, le
fabricant doit fournir une liste de tous les types d’antenne
approuvé pour une utilisation avec l’émetteur, ce qui
indique le gain maximal d’antenne permis (en dBi) et
requis d’impédance pour chacun.
• Antenne parabolique, gain: 12 dBi
• Antenne parabolique, gain: 26 dBi
• Antenne parabolique, gain: 29 dBi
59
Appendix F: Compliance Information
airFiber X User Guide
airFiber AF-4X
airFiber AF-5X
CAN ICES-3(B)/NMB-3(B)
CAN ICES-3(B)/NMB-3(B)
To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more
than that permitted for successful communication.
To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more
than that permitted for successful communication.
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions:
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause interference, and
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
CAN ICES-3(B)/NMB-3(B)
This radio transmitter (IC: 6545A-AF5X) has been approved
by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and
required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having
a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
Pour réduire le risque d’interférence aux autres utilisateurs,
le type d’antenne et son gain doivent être choisies de
façon que la puissance isotrope rayonnée équivalente
(PIRE) ne dépasse pas ce qui est nécessaire pour une
communication réussie.
Cet appareil est conforme à la norme RSS Industrie Canada
exempts de licence norme(s). Son fonctionnement est
soumis aux deux conditions suivantes:
• Dish antenna, gain: 23 dBi
• Dish antenna, gain: 30 dBi
1. Cet appareil ne peut pas provoquer d’interférences et
• Dish antenna, gain: 34 dBi
2. Cet appareil doit accepter toute interférence, y compris
les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
CAN ICES-3(B)/NMB-3(B)
Pour réduire le risque d’interférence aux autres utilisateurs,
le type d’antenne et son gain doivent être choisies de
façon que la puissance isotrope rayonnée équivalente
(PIRE) ne dépasse pas ce qui est nécessaire pour une
communication réussie.
Cet appareil est conforme à la norme RSS Industrie Canada
exempts de licence norme(s). Son fonctionnement est
soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas provoquer d’interférences et
2. Cet appareil doit accepter toute interférence, y compris
les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
Cet émetteur radio (IC: 6545A-AF5X) a été approuvée par
Industrie Canada pour l’exploitation avec l’antenne types
énumérés ci-dessous avec le gain maximal admissible
et requis l’impédance de l’antenne pour chaque type
d’antenne indiqué. Types d’antenne non inclus dans cette
liste, ayant un gain supérieur au gain maximal indiqué
pour ce type, sont strictement interdits pour une utilisation
avec cet appareil. Immédiatement suite à la remarque, le
fabricant doit fournir une liste de tous les types d’antenne
approuvé pour une utilisation avec l’émetteur, ce qui
indique le gain maximal d’antenne permis (en dBi) et
requis d’impédance pour chacun.
• Antenne parabolique, gain: 23 dBi
• Antenne parabolique, gain: 30 dBi
• Antenne parabolique, gain: 34 dBi
60
Ubiquiti Networks, Inc.
airFiber X User Guide
Appendix F: Compliance Information
RF Exposure Warning
Australia and New Zealand
airFiber AF-2X
airFiber AF-2X
The antennas used for this transmitter must be installed
to provide a separation distance of at least 126 cm from
all persons and must not be located or operating in
conjunction with any other antenna or transmitter.
Les antennes utilisées pour ce transmetteur doivent être
installé en considérant une distance de séparation de
toute personnes d’au moins 126 cm et ne doivent pas être
localisé ou utilisé en conflit avec tout autre antenne ou
transmetteur.
Warning: This is a Class B product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
airFiber AF-3X
airFiber AF-3X
The antennas used for this transmitter must be installed
to provide a separation distance of at least 364 cm from
all persons and must not be located or operating in
conjunction with any other antenna or transmitter.
Les antennes utilisées pour ce transmetteur doivent être
installé en considérant une distance de séparation de
toute personnes d’au moins 364 cm et ne doivent pas être
localisé ou utilisé en conflit avec tout autre antenne ou
transmetteur.
Warning: This is a Class B product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
airFiber AF-4X
airFiber AF-4X
The radiated output power of this device is below the FCC
radio frequency exposure limits. Nevertheless, the device
should be used in such a manner that the potential for
human contact during the normal operation is minimized.
In order to avoid the possibility of exceeding the FCC radio
frequency exposure limit, human proximity to the antenna
should be more than 180 cm.
La puissance de sortie rayonnée de cet appareil est
inférieure aux limites d’exposition de radio de fréquence
FCC. Néanmoins, le dispositif doit être utilisé de telle
manière que le potentiel pour le contact humain pendant
l’utilisation normale soit minimisé. Afin d’éviter la
possibilité de dépasser la limite d’exposition de fréquence
radio de la FCC, la proximité humaine à l’antenne devrait
être plus que 180 cm.
Warning: This is a Class B product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
airFiber AF-5X
Warning: This is a Class B product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
airFiber AF-5X
The antennas used for this transmitter must be installed
to provide a separation distance of at least 126 cm from
all persons and must not be located or operating in
conjunction with any other antenna or transmitter.
Les antennes utilisées pour ce transmetteur doivent être
installé en considérant une distance de séparation de
toute personnes d’au moins 126 cm et ne doivent pas être
localisé ou utilisé en conflit avec tout autre antenne ou
transmetteur.
Ubiquiti Networks, Inc.
61
Appendix F: Compliance Information
airFiber X User Guide
CE Marking
airFiber AF-4X Compliance
airFiber AF-2X
The user is responsible for obtaining all licenses that are
required by the local country in which the product will
be operated, and all such licenses must be obtained prior
to operation in the particular country. For information on
licenses required by your country as well as conditions of
use for the 4 GHz band, contact your appropriate national
authority.
CE marking on this product represents the product is in
compliance with all directives that are applicable to it.
airFiber AF-3X
CE marking on this product represents the product is in
compliance with all directives that are applicable to it.
4.9 GHz Band Devices (FCC and Industry
Canada)
The 4.9 GHz band is a licensed band allocated to public
safety services. State and local government entities that
provide public safety services are eligible to apply for
4.9 GHz licenses. For additional information, refer to FCC or
Industry Canada regulations.
airFiber AF-4X
CE marking on this product represents the product is in
compliance with all directives that are applicable to it.
airFiber AF-5X
CE marking on this product represents the product is in
compliance with all directives that are applicable to it.
Alert sign! follows CE marking
Alert sign must be indicated if a restriction on use applied
to the product and it must follow the CE marking.
62
Ubiquiti Networks, Inc.
airFiber X User Guide
Frequency Ranges and Power Levels
per Country/Region
airFiber AF-2X
The product can be operated in the countries and regions
listed in the following table, within the stated frequency
ranges and output power (EIRP) limits.
Each country has its own power level and frequency
regulations. To ensure the product operates under the
necessary regulatory compliance rules, the country
where the device will be used must be selected during
installation. The frequency settings and output power
(EIRP) limits will be tuned according to the regulations of
the selected country/region:
Appendix F: Compliance Information
Country/Region
Frequency Range
(Band Edges in MHz)
Max. EIRP (dBm)
Argentina
2400-2483
36
Australia
2400-2483
36
Bahrain
2400-2483
36
Brazil
2400-2483
36
Canada
2400-2483
   36*
Chile
2400-2483
36
China
2400-2483
36
Colombia
2400-2483
36
Ecuador
2400-2483
36
Ghana
2400-2483
36
Guam
(U.S. territory)
2400-2483
   36*
Hong Kong
2400-2483
36
Indonesia
2400-2483
36
India
2400-2483
36
Kenya
2400-2483
36
Korea Republic
2400-2483
36
Kyrgyzstan
2400-2483
Not applicable
Malaysia
2400-2483
36
Mexico
2400-2483
36
New Zealand
2400-2483
36
Nigeria
2400-2483
36
Peru
2400-2483
36
Philippines
2400-2483
36
Puerto Rico
(U.S. territory)
2400-2483
   36*
Singapore
2400-2483
36
South Africa
2400-2483
36
Taiwan
2400-2483
36
Tajikistan
2400-2483
Not applicable
Thailand
2400-2483
20
Turkmenistan
2400-2483
Not applicable
Uganda
2400-2483
Not applicable
United States
2400-2483
   36*
Uzbekistan
2400-2483
Not applicable
Venezuela
2400-2483
36
Virgin Islands
(U.S. territory)
2400-2483
   36*
Vietnam
2400-2483
36
* A higher EIRP is possible based on FCC Part 15 requirements
of reduction of conducted power by 1 dBm per 3 dBi increase of
antenna gain beyond 6 dBi.
Ubiquiti Networks, Inc.
63
Appendix F: Compliance Information
airFiber AF-3X
The product can be operated in the countries and regions
listed in the following table, within the stated frequency
ranges and output power (EIRP) limits.
Each country has its own power level and frequency
regulations. To ensure the product operates under the
necessary regulatory compliance rules, the country
where the device will be used must be selected during
installation. The frequency settings and output power
(EIRP) limits will be tuned according to the regulations of
the selected country/region:
64
airFiber X User Guide
Country/Region
Frequency Range
(Band Edges in MHz)
Max. EIRP (dBm)
Austria
3410-3900
66
Belgium
3410-3900
66
Bulgaria
3410-3900
66
Canada
3450-3650
3650-3700
57
44
Croatia
3410-3900
66
Cyprus
3410-3900
66
Czech Republic
3410-3900
66
Denmark
3410-3900
66
Estonia
3410-3900
66
Finland
3410-3900
66
France
3410-3900
66
Germany
3410-3900
66
Greece
3410-3900
66
Guam
(U.S. territory)
3650-3700
44
Hungary
3410-3900
66
Ireland
3410-3900
66
Italy
3410-3900
66
Latvia
3410-3900
66
Lithuania
3410-3900
66
Malta
3410-3900
66
Netherlands
3410-3900
66
Poland
3410-3900
66
Portugal
3410-3900
66
Puerto Rico
(U.S. territory)
3650-3700
44
Romania
3410-3900
66
Slovakia
3410-3900
66
Spain
3410-3900
66
Sweden
3410-3900
66
United Kingdom
3410-3900
66
United States
3650-3700
44
Virgin Islands
(U.S. territory)
3650-3700
44
Ubiquiti Networks, Inc.
airFiber X User Guide
airFiber AF-4X
The product can be operated in the countries and regions
listed in the following table, within the stated frequency
ranges and output power (EIRP) limits.
Users are responsible to comply with all local regulatory
rules and requirements beyond what is stated in the table.
Each country has its own power level and frequency
regulations. To ensure the product operates under the
necessary regulatory compliance rules, the country
where the device will be used must be selected during
installation. The frequency settings and output power
(EIRP) limits will be tuned according to the regulations of
the selected country/region:
Ubiquiti Networks, Inc.
Appendix F: Compliance Information
Country/Region
Frequency Range
(Band Edges in MHz)
Max. EIRP (dBm)
Austria
3410-3900
55
Belgium
3410-3900
55
Bulgaria
3410-3900
55
Canada
4940-4990
55
Croatia
3410-3900
55
Cyprus
3410-3900
55
Czech Republic
3410-3900
55
Denmark
3410-3900
55
Estonia
3410-3900
55
Finland
3410-3900
55
France
3410-3900
55
Germany
3410-3900
55
Greece
3410-3900
55
Guam
(U.S. territory)
4940-4990
55
Hungary
3410-3900
55
Ireland
3410-3900
55
Italy
3410-3900
55
Latvia
3410-3900
55
Lithuania
3410-3900
55
Malta
3410-3900
55
Netherlands
3410-3900
55
Poland
3410-3900
55
Portugal
3410-3900
55
Puerto Rico
(U.S. territory)
4940-4990
55
Romania
3410-3900
55
Slovakia
3410-3900
55
Spain
3410-3900
55
Sweden
3410-3900
55
United Kingdom
3410-3900
55
United States
4940-4990
55
Virgin Islands
(U.S. territory)
4940-4990
55
65
Appendix F: Compliance Information
airFiber X User Guide
airFiber AF-5X
The product can be operated in the countries and regions listed in the following table, within the stated frequency ranges
and output power (EIRP) limits.
Each country has its own power level and frequency regulations. To ensure the product operates under the necessary
regulatory compliance rules, the country where the device will be used must be selected during installation. The frequency
settings and output power (EIRP) limits will be tuned according to the regulations of the selected country/region:
5.1 GHz
5.2 GHz
Country/Region
Frequency Range
(Band Edges in
MHz)
Max.
EIRP
(dBm)
Argentina
5150-5250
49
Frequency Range
(Band Edges in
MHz)
5.4 GHz
Max.
EIRP
(dBm)
5.8 GHz
Frequency Range
(Band Edges in
MHz)
Max.
EIRP
(dBm)
Frequency Range
(Band Edges in
MHz)
Max.
EIRP
(dBm)
5470-5725
30
5725-5850
36
5470-5600,
5650-5725
30
5725-5855
36
Bahrain
5735-5835
20
Barbados
5725-5850
36
Belize
5735-5835
30
Bolivia
5735-5835
30
5725-5850
53
5735-5835
20
5725-5850
60
5735-5835
20
5735-5835
30
5735-5835
30
5735-5835
30
5725-5795,
5815-5850
36
5735-5835
30
5735-5835
30
5735-5835
30
Australia
Brazil
5470-5725
30
Brunei
Darussalam
Canada
5250-5350
30
Chile
5250-5350
30
5470-5600,
5650-5725
30
China
Colombia
5250-5350
30
Costa Rica
Denmark
5470-5725
30
Dominican
Republic
Ecuador
5150-5250
49
5250-5350
30
El Salvador
Finland
5470-5725
30
5725-5795,
5815-5850
36
Germany
5470-5725
30
5755-5875
36
Greece
5470-5725
30
5725-5795
36
Grenada
5470-5725
30
5725-5850
36
5735-5835
30
Guatemala
Honduras
5470-5725
30
5725-5850
36
5470-5725
30
5725-5850
36
5470-5725
30
5725-5875
36
India
5825-5875
36
Iraq
5735-5835
36
5725-5875
33
5725-5850
36
Hong Kong
Iceland
66
5250-5350
30
Ireland
5470-5725
30
Italy
5470-5725
30
Jamaica
5470-5725
30
Ubiquiti Networks, Inc.
airFiber X User Guide
Appendix F: Compliance Information
5.1 GHz
Country/Region
Frequency Range
(Band Edges in
MHz)
5.2 GHz
Max.
EIRP
(dBm)
Kenya
5.4 GHz
Frequency Range
(Band Edges in
MHz)
Max.
EIRP
(dBm)
5250-5350
30
Korea Republic
Frequency Range
(Band Edges in
MHz)
5490-5710
5.8 GHz
Max.
EIRP
(dBm)
30
Lebanon
Liechtenstein
5470-5725
30
Macau
Frequency Range
(Band Edges in
MHz)
Max.
EIRP
(dBm)
5735-5835
30
5735-5815
30
5735-5835
30
5725-5795,
5815-5875
36
5725-5850
36
5735-5835
30
Mexico
5735-5835
30
Morocco
5735-5835
20
Nepal
5735-5835
30
Malaysia
5150-5250
49
5250-5350
30
New Zealand
5470-5725
30
5725-5850
53
Norway
5470-5725
30
5725-5795,
5815-5850
53
Oman
5470-5725
30
5725-5850
36
Pakistan
5735-5835
30
Panama
5735-5835
30
Papua New
Guinea
5735-5835
30
Peru
5150-5250
49
5250-5350
30
5470-5725
30
5725-5850
36
Philippines
5150-5250
49
5250-5350
30
5470-5725
30
5725-5850
36
5470-5725
30
5725-5875
36
5470-5600,
5650-5725
30
5725-5850
60
5735-5835
30
5650-5950
53
5735-5835
30
Portugal
Puerto Rico
(U.S. territory)
5250-5350
30
Qatar
Russia
5150-5350
43
5470-5650
23
Singapore
South Africa
5470-5725
30
5725-5850
60
Spain
5470-5725
30
5725-5795,
5815-5855
36
Switzerland
5470-5725
30
5725-5795,
5815-5855
36
Taiwan
5250-5350
30
5490-5710
30
5735-5815
30
Thailand
5250-5350
30
5470-5725
30
5725-5850
36
Trinidad And
Tobago
5470-5725
30
5725-5850
36
United
Kingdom
5470-5725
30
5725-5790,
5815-5850
36
5470-5600,
5650-5725
30
5725-5850
60
Uruguay
5470-5725
30
5725-5850
36
Uzbekistan
5470-5725
30
5725-5850
36
5735-5835
30
United States
Venezuela
5150-5250
5150-5250
Ubiquiti Networks, Inc.
49
49
5250-5350
5250-5350
30
30
67
Appendix F: Compliance Information
airFiber X User Guide
The following table lists the maximum transmit output
power (EIRP) for the 5.1 GHz band.
5.1 GHz Band
Channel Bandwidth
10 MHz
20 MHz
30 MHz
40 MHz
50 MHz
68
Frequency Range
(Band Edges in MHz)
Maximum
Transmit Output
Power (EIRP)
in dBm
5155-5175
39
5166-5186
44
5177-5250
49
5156-5180
37
5161-5185
39
5166-5209
44
5190-5250
49
5155-5192
37
5163-5202
39
5173-5211
44
5182-5250
49
5155-5204
37
5165-5219
39
5180-5228
44
5189-5250
49
5155-5214
37
5165-5233
39
5184-5242
44
5193-5250
49
Ubiquiti Networks, Inc.
airFiber X User Guide
RoHS/WEEE Compliance Statement
English
European Directive 2012/19/EU requires that the
equipment bearing this symbol on the product and/
or its packaging must not be disposed of with unsorted
municipal waste. The symbol indicates that this product
should be disposed of separately from regular household
waste streams. It is your responsibility to dispose
of this and other electric and electronic equipment
via designated collection facilities appointed by the
government or local authorities. Correct disposal
and recycling will help prevent potential negative
consequences to the environment and human health. For
more detailed information about the disposal of your old
equipment, please contact your local authorities, waste
disposal service, or the shop where you purchased the
product.
Deutsch
Die Europäische Richtlinie 2012/19/EU verlangt, dass
technische Ausrüstung, die direkt am Gerät und/oder an
der Verpackung mit diesem Symbol versehen ist , nicht
zusammen mit unsortiertem Gemeindeabfall entsorgt
werden darf. Das Symbol weist darauf hin, dass das
Produkt von regulärem Haushaltmüll getrennt entsorgt
werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät
und andere elektrische und elektronische Geräte über die
dafür zuständigen und von der Regierung oder örtlichen
Behörden dazu bestimmten Sammelstellen zu entsorgen.
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu
bei, potentielle negative Folgen für Umwelt und die
menschliche Gesundheit zu vermeiden. Wenn Sie weitere
Informationen zur Entsorgung Ihrer Altgeräte benötigen,
wenden Sie sich bitte an die örtlichen Behörden oder
städtischen Entsorgungsdienste oder an den Händler, bei
dem Sie das Produkt erworben haben.
Ubiquiti Networks, Inc.
Appendix F: Compliance Information
Español
La Directiva 2012/19/UE exige que los equipos que
lleven este símbolo en el propio aparato y/o en su
embalaje no deben eliminarse junto con otros residuos
urbanos no seleccionados. El símbolo indica que el
producto en cuestión debe separarse de los residuos
domésticos convencionales con vistas a su eliminación. Es
responsabilidad suya desechar este y cualesquiera otros
aparatos eléctricos y electrónicos a través de los puntos
de recogida que ponen a su disposición el gobierno y las
autoridades locales. Al desechar y reciclar correctamente
estos aparatos estará contribuyendo a evitar posibles
consecuencias negativas para el medio ambiente y la
salud de las personas. Si desea obtener información más
detallada sobre la eliminación segura de su aparato usado,
consulte a las autoridades locales, al servicio de recogida
y eliminación de residuos de su zona o pregunte en la
tienda donde adquirió el producto.
Français
La directive européenne 2012/19/UE exige que
l’équipement sur lequel est apposé ce symbole sur le
produit et/ou son emballage ne soit pas jeté avec les
autres ordures ménagères. Ce symbole indique que
le produit doit être éliminé dans un circuit distinct
de celui pour les déchets des ménages. Il est de votre
responsabilité de jeter ce matériel ainsi que tout autre
matériel électrique ou électronique par les moyens de
collecte indiqués par le gouvernement et les pouvoirs
publics des collectivités territoriales. L’élimination et le
recyclage en bonne et due forme ont pour but de lutter
contre l’impact néfaste potentiel de ce type de produits
sur l’environnement et la santé publique. Pour plus
d’informations sur le mode d’élimination de votre ancien
équipement, veuillez prendre contact avec les pouvoirs
publics locaux, le service de traitement des déchets, ou
l’endroit où vous avez acheté le produit.
Italiano
La direttiva europea 2012/19/UE richiede che le
apparecchiature contrassegnate con questo simbolo sul
prodotto e/o sull’imballaggio non siano smaltite insieme
ai rifiuti urbani non differenziati. Il simbolo indica che
questo prodotto non deve essere smaltito insieme ai
normali rifiuti domestici. È responsabilità del proprietario
smaltire sia questi prodotti sia le altre apparecchiature
elettriche ed elettroniche mediante le specifiche strutture
di raccolta indicate dal governo o dagli enti pubblici
locali. Il corretto smaltimento ed il riciclaggio aiuteranno
a prevenire conseguenze potenzialmente negative per
l’ambiente e per la salute dell’essere umano. Per ricevere
informazioni più dettagliate circa lo smaltimento delle
vecchie apparecchiature in Vostro possesso, Vi invitiamo
a contattare gli enti pubblici di competenza, il servizio di
smaltimento rifiuti o il negozio nel quale avete acquistato
il prodotto.
69
Appendix F: Compliance Information
70
airFiber X User Guide
Ubiquiti Networks, Inc.
airFiber X User Guide
Appendix G: Declaration of
Conformity
Česky
[Czech]
UBIQUITI NETWORKS tímto prohlašuje, že toto UBIQUITI
NETWORKS zařízení, je ve shod se základními požadavky a
dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk
[Danish]
Hermed, UBIQUITI NETWORKS, erklærer at denne UBIQUITI
NETWORKS enhed, er i overensstemmelse med de væsentlige
krav og øvrige relevante krav i direktiv 1999/5/EF.
Nederlands
[Dutch]
Hierbij verklaart UBIQUITI NETWORKS, dat deze UBIQUITI
NETWORKS apparaat, in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn 1999/5/EC.
English
Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI
NETWORKS device, is in compliance with the essential
requirements and other relevant provisions of Directive
1999/5/EC.
Eesti
[Estonian]
Käesolevaga UBIQUITI NETWORKS kinnitab, et antud UBIQUITI
NETWORKS seade, on vastavus olulistele nõuetele ja teistele
asjakohastele sätetele direktiivi 1999/5/EÜ.
Suomi
[Finnish]
Täten UBIQUITI NETWORKS vakuuttaa, että tämä UBIQUITI
NETWORKS laite, on yhdenmukainen olennaisten vaatimusten ja
muiden sitä koskevien direktiivin 1999/5/EY.
Français
[French]
Par la présente UBIQUITI NETWORKS déclare que l’appareil
UBIQUITI NETWORKS, est conforme aux exigences essentielles et
aux autres dispositions pertinentes de la directive 1999/5/CE.
Deutsch
[German]
Hiermit erklärt UBIQUITI NETWORKS, dass sich dieses UBIQUITI
NETWORKS Gerät, in Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten Vorschriften der
Richtlinie 1999/5/EG befindet.
Ελληνική
[Greek]
Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η
συσκευή UBIQUITI NETWORKS, είναι σε συμμόρφωση με τις
βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας
1995/5/ΕΚ.
Magyar
[Hungarian]
Ezennel UBIQUITI NETWORKS kijelenti, hogy ez a UBIQUITI
NETWORKS készülék megfelel az alapvető követelményeknek és
más vonatkozó 1999/5/EK irányelv rendelkezéseit.
Íslenska
[Icelandic]
Hér, UBIQUITI NETWORKS, því yfir að þetta UBIQUITI NETWORKS
tæki er í samræmi við grunnkröfur og önnur viðeigandi ákvæði
tilskipun 1999/5/EC.
Italiano
[Italian]
Con la presente, UBIQUITI NETWORKS, dichiara che questo
dispositivo UBIQUITI NETWORKS, è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti della direttiva
1999/5/CE.
Latviski
[Latvian]
Ar šo, UBIQUITI NETWORKS, deklarē, ka UBIQUITI NETWORKS
ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem
noteikumiem Direktīvā 1999/5/EK.
Lietuviškai
[Lithuanian]
UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS
įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB
Direktyvos nuostatas.
Malti
[Maltese]
Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz
UBIQUITI NETWORKS huwa konformi mar-rekwiżiti essenzjali u
dispożizzjonijiet rilevanti oħrajn ta ‘Direttiva 1999/5/EC.
Norsk
[Norwegian]
Herved UBIQUITI NETWORKS, erklærer at denne UBIQUITI
NETWORKS enheten, er i samsvar med de grunnleggende
kravene og andre relevante bestemmelser i direktiv 1999/5/EF.
Slovensky
[Slovak]
Týmto UBIQUITI NETWORKS, prehlasuje, že toto UBIQUITI
NETWORKS zariadenie, je v súlade so základnými požiadavkami a
ďalšími relevantnými ustanoveniami smernice 1999/5/ES.
Svenska
[Swedish]
Härmed UBIQUITI NETWORKS, intygar att denna UBIQUITI
NETWORKS enhet är i överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som framgår
av direktiv 1999/5/EG.
Ubiquiti Networks, Inc.
Appendix G: Declaration of Conformity
Español
[Spanish]
Por medio de la presente UBIQUITI NETWORKS declara que este
dispositivo UBIQUITI NETWORKS, cumple con los requisitos
esenciales y cualesquiera otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE.
Polski
[Polish]
Niniejszym, Ubiquiti Networks, oświadcza, że ​​urządzenie
UBIQUITI NETWORKS, jest zgodny z zasadniczymi wymaganiami
oraz pozostałymi stosownymi postanowieniami Dyrektywy
1999/5/EC.
Português
[Portuguese]
UBIQUITI NETWORKS declara que este dispositivo UBIQUITI
NETWORKS, está conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
Română
[Romanian]
Prin prezenta, UBIQUITI NETWORKS declară că acest dispozitiv
UBIQUITI NETWORKS este în conformitate cu cerințele esențiale
și alte prevederi relevante ale Directivei 1999/5/CE.
71
Appendix G: Declaration of Conformity
72
airFiber X User Guide
Ubiquiti Networks, Inc.
airFiber X User Guide
Appendix H: Contact Information
Appendix H: Contact
Information
Ubiquiti Networks Support
Ubiquiti Support Engineers are located around the world
and are dedicated to helping customers resolve software,
hardware compatibility, or field issues as quickly as
possible. We strive to respond to support inquiries within
a 24-hour period.
Ubiquiti Networks, Inc.
2580 Orchard Parkway
San Jose, CA 95131
www.ubnt.com
Online Resources
Support: ubnt.link/airFiber-Support
Community: community.ubnt.com/airfiber
Downloads: downloads.ubnt.com/airfiber
AI040116
Ubiquiti Networks, Inc.
73
www.ubnt.com
©2016 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airFiber, airOS, RocketDish,
TOUGHCable, and xRT are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are
the property of their respective owners.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Modify Date                     : 2016:04:19 17:15:25-07:00
Create Date                     : 2016:04:19 17:15:24-07:00
Metadata Date                   : 2016:04:19 17:15:25-07:00
Creator Tool                    : Adobe InDesign CC 2015 (Macintosh)
Format                          : application/pdf
Title                           : airFiber X User Guide
Creator                         : A Imaoka
Document ID                     : uuid:1370bcab-8753-47fd-83d7-cecddef70fbc
Instance ID                     : uuid:4b9e4961-c5c0-42b4-83a3-e3b449f09151
Producer                        : Adobe PDF Library 15.0
Page Count                      : 20
Author                          : A Imaoka

EXIF Metadata provided by EXIF.tools