Westell A90328XX-07 Spread Spectrum Transmitter User Manual PRODUCT DESCRIPTION

Download:
Mirror Download [FCC.gov]
Document ID	528327
Application ID	TDBGiV2MW2FPx1pVpKvCtg==
Document Description	Users Manual Part3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	265.73kB (3321633 bits)
Date Submitted	2005-03-31 00:00:00
Date Available	2005-03-31 00:00:00
Creation Date	2005-03-31 14:15:05
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2005-03-31 14:15:16
Document Title	PRODUCT DESCRIPTION
Document Creator	Acrobat PDFMaker 5.0 for Word
Document Author:	SAllen

User Guide
If you select ETHERNET PORT 1 from the WAN Port drop-down arrow, the following screen will be displayed.
Click OK.
If you click on OK in the preceding pop-up screen, the following screen will be displayed. Click on OK. If you
click on Cancel, the change will not take effect.
If you clicked on OK in the preceding pop-up screen, the following pop-up screen will appear. The Router must be
reset to allow the new configuration to take effect. Click on OK.
If you clicked on OK in the preceding screen, the following screen will be displayed. The Router will be reset and
the new configuration will take effect.
030-300432 Rev. A
111
December 2004
User Guide
After the Router has been reset, the DSL LED will be OFF. This is because the DSL transceiver has now been
disabled. However, the Power, Ethernet, and Wireless LEDs will remain lit.
13.6.4 Editing the Router’s VC Configuration
The following VC 1 Configuration screen will be displayed if you click on the edit button adjacent to any of the
‘Enabled’ protocols displayed in the WAN Configuration screen. (Note: The Protocol must be enabled before you
can edit its VC configuration.) The VC 1 Configuration screen allows you to edit your virtual connection (VC). A
virtual connection identifies a connection through the service provider’s ATM network to your ISP. Unlike physical
hardware connections, virtual connections are defined by data.
If you change any of the VC settings in the following screen, click the Set VC button to save the settings.
NOTE: If you experience any problems, please reset the Router via the external hardware reset button or via the
procedure defined under the Maintenance menu in section 15.1. The actual information displayed in this screen
may vary, depending on network connection established.
030-300432 Rev. A
112
December 2004
User Guide
VPI
VCI
PCR
QoS
030-300432 Rev. A
VC 1 Configuration
This setting allows you to change your VPI (Virtual Path Indicator) value for a
particular VC, which is defined by your Service Provider.
This setting allows you to change your VCI (Virtual Channel Indicator) value for a
particular VC, which is defined by your Service Provider.
Factory Default = 100%
Peak Cell Rate (PCR)-The maximum rate at which cells can be transmitted across a
virtual circuit, specified in cells per second and defined by the interval between the
transmission of the last bit of one cell and the first bit of the next.
This value is a percentage of the current data rate.
100 allows this VC to use 100% of the available bandwidth.
80 allows this VC to use 80% of the available bandwidth.
Quality of Service, which is determined by your Service Provider.
Possible Responses:
CBR = Constant Bit Rate
UBR = Unspecified Bit Rate
VBR = Variable Bit Rate
113
December 2004
User Guide
Protocol
Status
IP Address
Gateway
DNS Primary
DNS Secondary
MRU Negotiation
LCP Echo Disable
LCP Echo Failures
LCP Echo Retry Duration
LCP Echo Retry Duration
Tunneling
The Protocol for each VC, which is specified by your Service Provider.
Possible Responses:
PPPoA = Point to Point Protocol over ATM (Asynchronous Transfer Mode)
PPPoE = Point to Point Protocol over Ethernet
Bridge = Bridge Protocol
Classical IPoA = Internet Protocol over ATM (Asynchronous Transfer Mode). This
is an ATM encapsulation of the IP protocol.
The protocol status.
VC x PPPoE Settings
Displays the IP network address that your modem is on.
Displays the Router’s IP address
Provided by your Service Provider
Provided by your Service Provider
Factory Default = DISABLED
If ENABLED, the Maximum Received Unit (MRU) would enforce MRU
negotiations. (NOTE: enable this option only at your Internet Service Provider’s
request.)
Factory Default = Enable
If checked, this option will disable the modem LCP Echo transmissions.
Indicates number of continuous LCP echo non-responses received before the PPP
session is terminated.
The interval between LCP Echo transmissions with responses.
The interval between LCP. Echo after no response.
Factory Default = ENABLE
If ENABLED, this option allows PPP traffic to be bridged to the WAN. This feature
allows you to use a PPPoE shim on the host computer to connect to the Internet
Service Provider, by bypassing the Router’s capability to do this.
NOTE: Tunneling is available in PPPoE mode only.
NOTE: The values for the IP Address, Gateway, DNS Primary, and DNS Secondary are all “Override of the value
obtained from the PPP connection,” They default to “0.0.0.0,” in which case the override is ignored. Westell
recommends that you do not change the values unless your Internet service provider instructs you to change them.
030-300432 Rev. A
114
December 2004
User Guide
If you have made any changes to your VC settings, you need to save them. To save the new VC settings, click on
OK when asked Set this PPPoE VC configuration? If you click on cancel, the new VC settings will not be saved.
If you clicked on OK in the preceding pop-up screen, the following pop-up screen will appear. The Router must be
reset to allow the new configuration to take effect. Click OK.
If you clicked OK in the preceding screen, the following screen will be displayed. The Router will be reset and the
new configuration will take effect.
After a brief delay, the home page will be displayed. Confirm that you have a DSL sync and that your PPP session
displays UP. (Click on the connect button to establish a PPP session).
030-300432 Rev. A
115
December 2004
User Guide
13.6.5 Configuring the Router’s Protocol Settings for PPPoE Mode
If you are using Models 7400, 7401 select Advanced WAN > VC from the Configuration menu to configure the
Router’s protocol settings for PPPoE mode. If you are using Models 328W10, 328W11, select Advanced WAN >
WAN from the Configuration menu to configure the Router’s protocol settings for PPPoE mode.
The VC Configuration screen will be displayed. Next, click on the edit button adjacent to any of the existing
‘Enabled’ VC (Virtual Connection) protocols. (Note: The protocol status must display “Enable” to allow edits to its VC
configuration.).
If you clicked edit in the VC Configuration screen, the following VC 1 Configuration screen will be displayed.
Select PPPoE from the options listed in Protocol drop-down arrow. After you have made changes to VC 1
Configuration screen, click the set VC button.
If you click the set VC button, the following pop-up screen will be displayed. Click on OK in the pop-up screen. If
you click on Cancel, the new settings will not be saved. After you click on OK, follow the instructions to reset the
Router, as previously discussed in section 13.6.4.
030-300432 Rev. A
116
December 2004
User Guide
13.6.6 Configuring the Router’s Protocol Settings for Bridge Mode
If you are using Models 7400, 7401 select Advanced WAN > VC from the Configuration menu to configure the
Router’s protocol settings for Bridge mode. If you are using Models 328W10, 328W11, select Advanced WAN >
WAN from the Configuration menu to configure the Router’s protocol settings for Bridge mode.
The VC Configuration screen will be displayed. Next, click on the edit button adjacent to any of the existing
‘Enabled’ VC (Virtual Connection) protocols. (Note: The protocol status must display “Enable” to allow edits to its VC
configuration.)
If you clicked edit in the VC Configuration screen, the following VC 1 Configuration screen will be displayed.
Select Bridge from the options listed in Protocol drop-down arrow. Next, select a mode from the options listed in
the Mode drop-down arrow, under VC1 – Bridge Settings. After you have made changes to VC 1 Configuration
screen, click the set VC button.
030-300432 Rev. A
117
December 2004
User Guide
VC 1 Configuration
This setting allows you to change your VPI (Virtual Path Indicator) value for a
particular VC, which is defined by your Service Provider.
This setting allows you to change your VCI (Virtual Channel Indicator) value for a
particular VC, which is defined by your Service Provider.
Factory Default = 100%
Peak Cell Rate (PCR)-The maximum rate at which cells can be transmitted across a
virtual circuit, specified in cells per second and defined by the interval between the
transmission of the last bit of one cell and the first bit of the next.
VPI
VCI
PCR
QoS
Protocol
Status
Mode
This value is a percentage of the current data rate.
100 allows this VC to use 100% of the available bandwidth.
80 allows this VC to use 80% of the available bandwidth.
Quality of Service, which is determined by your Service Provider.
Possible Response:
CBR = Constant Bit Rate
UBR = Unspecified Bit Rate
VBR = Variable Bit Rate
The Protocol for each VC, which is specified by your Service Provider.
Possible Response:
PPPoA = Point to Point Protocol over ATM (Asynchronous Transfer Mode)
PPPoE = Point to Point Protocol over Ethernet
Bridge = Bridge Protocol
Classical IPoA = Internet Protocol over ATM (Asynchronous Transfer Mode). This
is an ATM encapsulation of the IP protocol.
The protocol status.
VC 1 Bridge Settings
Bridge = A bridge is a layer 2 device that connects two segments of the same LAN that use the
same protocol such as Ethernet. The modem does not have a WAN IP address in this mode. The
client PC will typically get an IP address from a DHCP server in the network or the IP address can
be assigned to the client PC statically.
Routed Bridge = Routed Bridged Encapsulation (RBE) is the process by which a bridged segment
is terminated on a routed interface. Specifically, the Router is routing on an IEEE 802.3 or
Ethernet header carried over RFC 1483 bridged ATM. RBE was developed to address the known
RFC1483 bridging issues, including broadcast storms and security. The modem will get a WAN
IP address through DHCP or can be assigned statically. NAT will use the global address assigned
to the modem.
Proxy Bridge = Proxy Bridge is the process in which the modem acts as a proxy ARP agent for a
local public subnet. The modem will be assigned an IP address from within that public subnet.
The modem will direct all traffic to a Router, which is configured statically. The Router’s address
must not reside within Router’s assigned public subnet. All traffic will be sent via the Router’s
MAC address. The LAN may also have a private NAT'ed network. NAT will use the global
address assigned to the modem.
VLAN Bridge = Assigns VLAN tags to individual data ports on the modem.
030-300432 Rev. A
118
December 2004
User Guide
If you selected the Routed Bridge mode under VC 1- Bridge Settings, the following screen will be displayed.
Enter the appropriate values in the fields and click on set VC.
Mode
DHCP Client
IP Address
Subnet Mask
Gateway
DNS Primary
DNS Secondary
030-300432 Rev. A
VC 1 – Bridge Settings (Routed Bridge)
The Mode you have selected to use with Bridge protocol.
Selecting a radio button allows you to either Enable or Disable the DHCP Client.
Displays the IP network address that your modem is on.
Displays the subnet mask, which determines if an IP address belongs to your local network.
Displays the Router’s IP gateway address.
Provided by your Service Provider.
Provided by your Service Provider.
119
December 2004
User Guide
If you selected Proxy Bridge mode under VC 1- Bridge Settings, the following screen will be displayed. Enter the
appropriate values in the fields and click on set VC.
Mode
Gateway
DNS Primary
DNS Secondary
030-300432 Rev. A
VC 1 - Bridge Settings (Proxy Bridge)
The Mode you have selected to use with Bridge protocol.
Displays the Router’s IP address.
Provided by your Service Provider.
Provided by your Service Provider.
120
December 2004
User Guide
If you selected VLAN Bridge under VC 1- Bridge Settings, the following screen will be displayed. Enter the
appropriate values in the fields and click on set VC.
Mode
VLAN ID
VLAN Priority
VLAN on WAN
030-300432 Rev. A
VC 1 - Bridge Settings (VLAN Bridge)
The Mode you have selected to use with Bridge protocol.
VLAN is used to assign VLAN tags to individual data ports on the modem.
Assigns a VLAN ID to the port.
This will set the VLAN priority for the port.
Factory Default = DISABLE
Selecting Enable allows VLAN tagging to occur according to the data port’s
configuration.
121
December 2004
User Guide
After you have configured the VC 1 Configuration screen, you must click the set VC button to save your VC
settings.
If you click the set VC button, the following pop-up screen will be displayed. Click on OK in the pop-up screen. If
you click on Cancel, the new settings will not be saved. After you click on OK, follow the instructions to reset the
Router, as previously discussed in section 13.6.4.
030-300432 Rev. A
122
December 2004
User Guide
13.6.7 Configuring VC Protocol Settings for ETHERNET PORT 1 (Models
328W10 and 328W11 only)
To configure the Router’s VC settings via the Ethernet UPLINK/E1 port, select ETHERNET PORT 1 at the WAN
Port drop-down arrow. By selecting ETHERNET PORT 1, you will disable the Router’s DSL transceiver. This
will enable the WAN Ethernet port and allow the WAN interface to use the UPLINK/E1 Port.
If you select ETHERNET PORT 1, the following pop-up will be displayed. Click on OK.
030-300432 Rev. A
123
December 2004
User Guide
If you click on OK, the following pop-up screen will be displayed. Click on OK.
If you clicked on OK in the preceding pop-up screen, the following pop-up screen will be displayed. Click on OK.
If you clicked on OK, the following screen will be displayed. The Router will be reset and the new configuration
will take effect.
030-300432 Rev. A
124
December 2004
User Guide
After the Router has been reset, select Advanced WAN > WAN from the Configuration menu. The following
screen will be displayed.
If you click edit, the following screen will be displayed. By using this screen, you can configure the WAN Ethernet
port settings of your Router.
030-300432 Rev. A
125
December 2004
User Guide
To configure the WAN Ethernet port for Routed Bridge protocol, select ROUTED from the Protocol drop-down
arrow.
If you select ROUTED, the following screen will be displayed. Enter the appropriate values in the fields and click on set.
030-300432 Rev. A
126
December 2004
User Guide
If you clicked on set, the following pop-up screen will be displayed. Click on OK.
If you clicked on OK in the preceding pop-up screen, the following pop-up screen will appear. The Router must be
reset to allow the new configuration to take effect. Click on OK.
If you clicked on OK in the preceding screen, the following screen will be displayed. The Router will be reset and
the new configuration will take effect.
030-300432 Rev. A
127
December 2004
User Guide
After the modem has been reset, the WAN Configuration screen will display Routed Bridge as the protocol for
ETHERNET PORT 1.
030-300432 Rev. A
128
December 2004
User Guide
13.6.8 QOS
The following settings will be displayed if you select Advanced WAN > QOS from the Configuration menu. If you
change any settings in this screen, click on save. If you click on reset, this screen will refresh and display your
previously saved QOS configuration.
IMPORTANT: If you are using Model 328W10 or 328W11 and the Router is configured for ETHERNET PORT 1,
the QOS option will not be displayed in the Advanced WAN drop-down menu. You must configure the Router for
DSLATM PORT to access QOS. Refer to section 13.6.3.1 for details on enabling and disabling DSLATM PORT
and ETHERNET PORT 1.
NOTE: The QOS feature helps ensure data integrity in high-speed transmissions. QOS provides the capability to
partition network traffic into multiple priority levels or classes of service. After packet classification, other QOS
features can be utilized to assign the appropriate traffic handling policies including congestion management,
bandwidth allocation, and delay bounds for each traffic class.
QOS Enable
Turbo TCP Enable
QOS Filter Enable
030-300432 Rev. A
Factory Default = DISABLED
If this box is checked, Quality of Service (QOS) will be Enabled.
Factory Default = DISABLED
If this box is checked, Turbo TCP will be Enabled.
QOS Configuration
Factory Default = DISABLED
If this box is checked, this will Enable the QOS filter.
129
December 2004
User Guide
QOS Classification
Peak Information Rte (%)
Committed Information Rate (%)
Peak Burst Size
Committed Burst Size
Max Queue Size
Latency Boundary
Latency Threshold (ms)
IP Fragmentation Enable
IP Fragment Size
This feature provides the capability to partition network traffic into multiple
priority levels or classes of service. After packet classification, other QOS
features can be utilized to assign the appropriate traffic handling policies
including congestion management, bandwidth allocation, and delay bounds
for each traffic class.
Possible responses are:
Best Effort (BE)
Assured Forwarding (AF1)
Assured Forwarding (AF2)
Assured Forwarding (AF3)
Assured Forwarding (AF4)
Expedited Forwarding (EF)
Network Control (NC)
The maximum allowed rate for this priority, expressed as a percentage of
the DSL rate.
The committed rate for this priority, expressed as a percentage of the DSL
rate.
The interval in milliseconds for averaging the peak offered rate.
The interval in milliseconds for averaging the committed offered rate.
The number of packets that can be queued for this priority.
Latency Measurements
This configures the maximum latency boundary in milliseconds that a
specific packet may be delayed by.
This setting configures the maximum latency boundary in milliseconds that
a specific packet may be delayed by.
Possible responses are:
Boundary 1:0 ms
Boundary 2:10 ms
Boundary 3:30 ms
Boundary 4:40 ms
Boundary 5:100 ms
Boundary 6:1000 ms
Boundary 7:3000 ms
Factory Default = DISABLED
If this box is checked, IP Fragmentation will be Enabled. If Enabled and
packets larger than 1500 bytes total are received, they will be fragmented.
This is the IP Packet Size.
Possible responses are:
100, 148, 244, 292, 340, 388, or 436
If you made changes to the QOS Configuration and clicked on save, the following screen will be displayed. Click
on OK. This will save your new QOS settings.
030-300432 Rev. A
130
December 2004
User Guide
13.6.9 Route
The following settings will be displayed if you select Advanced WAN > Route from the Configuration menu. The
Route table maintains the routes or paths of where specific types of data shall be routed across a network.
To add a Route, enter a Subnet Mask address, or check the Host Route box. Click on the add button to establish a
static route.
030-300432 Rev. A
131
December 2004
User Guide
IP Interfaces
Address
Subnet Mask
Name
Network Routing Table
Destination Address
Subnet Mask
Gateway
Interface
Metric
RIP
Host Routing Table
Destination Address
Subnet Mask
Gateway
Interface
Metric
RIP
Inactive Routes
Destination Address
Subnet Mask
Gateway
Interface
Metric
RIP
Add Route
Destination Address
Subnet Mask/ Host Route
Gateway/LAN Gateway
IP Address
Metric
RIP Conf
Save to Modem
030-300432 Rev. A
IP Interfaces
The list of active interfaces on the modem and their IP and Subnet mask address.
Eth0 is the local LAN interface.
Lo0 is the loopback interface.
MainPPP is the WAN interface
The IP interface address.
The IP interface subnet address.
The IP interface device name.
Network Routing Table
The list of network routes. These can be either routes for directly connected
interfaces or static routes.
The IP address or subnet of the Route.
If the Route is a network route, Subnet Mask is used to specify the subnet address.
If the Route is a Host route, then the Host Route check box is used.
Indicates were to send the packet if it matches this route.
Indicates were to send the packet if it matches this route.
The RIP metric to be assigned to this route if and when it is advertised using RIP.
Indicates whether a static route should be advertised via RIP.
Host Routing Table
The list of host routes. A host route is an IP route with a 32-bit mask, indicating a
single destination (as opposed to a subnet, which could match several destinations.)
The IP address or subnet of the Route.
If the Route is a network route, Subnet Mask is used to specify the subnet address.
If the Route is a Host route, then the Host Route check box is used.
Indicates were to send the packet if it matches this route.
Indicates were to send the packet if it matches this route.
The RIP metric to be assigned to this route if and when it is advertised using RIP.
Indicates whether a static route should be advertised via RIP.
Inactive Routes
Static routes whose interface is currently not in service.
The IP address or subnet of the Route.
If the Route is a network route, Subnet Mask is used to specify the subnet address.
If the Route is a Host route, then the Host Route check box is used.
Indicates were to send the packet if it matches this route.
Indicates were to send the packet if it matches this route.
The RIP metric to be assigned to this route if and when it is advertised using RIP.
Indicates whether a static route should be advertised via RIP.
Add Route
This is used to add a new static route in the modem.
The IP address or subnet of the Route.
If the Route is a network route, Subnet Mask is used to specify the subnet address.
If the Route is a Host route, then the Host Route check box is used.
The interface to use for sending the packet, if it matches this route. (Only active
Routers can be used to create a static route.)
The RIP metric to be assigned to this route if and when it is advertised using RIP.
Determines whether or not to advertise the static route, using RIP. (RIP must also be
enabled before the route will be advertised.)
If checked, then the route will be made permanent by saving it to flash memory. If
not checked, the route will disappear the next time the modem restarts.
132
December 2004
User Guide
13.6.10
RIP
The following details will be displayed if you select Advanced WAN > RIP from the Configuration menu. If you
change any settings in this screen, click on save. If you click on reset, this screen will refresh and display your last
saved RIP configuration.
RIP (Routing Interface Protocol) is a dynamic inter-network routing protocol primarily used in interior routing
environments. A dynamic routing protocol, as opposed to a static routing protocol, automatically discovers routes
and builds routing tables.
030-300432 Rev. A
133
December 2004
User Guide
RIP Enable
Interface Type
Receive
Transmit
RIPv2 Authentication Mode
Default Gateway
Border Gateway Filtering
RIP Timer Rate
RIP Supply Interval
RIP Expire Time
RIP Garbage Collection Time
Factory Default = DISABLED
If this box is checked, RIP will be Enabled (turned ON).
RIP Configuration
LAN: Select this if you are configuring RIP for the LAN side.
WAN: Select this if you are configuring RIP for the WAN side. (WAN side is
receive only.)
The version of RIP to be accepted.
Possible responses are:
None
RIPv1
RIPv2
RIPv1 or RIPv2
The version of RIP to be transmitted. (WAN side RIP never transmits)
Possible responses are:
None
RIPv1
RIPv1 Compatible
RIPv2
If using RIP V2, you must select the type of authentication to use.
Possible responses are:
None
Clear Text
MD5 (If MD5 authentication, the password)
Advanced
Factory Default = DISABLED
If this box is check (Enabled), this feature will determine whether the modem
advertises itself as the default Gateway (i.e., the default route)
Factory Default = ENABLED
If this box is unchecked (Disabled), the modem will not summarize subnets into
a single route before advertising.
Indicates how often to update the local routing table.
Indicates how often to advertise routes to neighbors.
Indicates how long routes received from neighbors become invalid, if no refresh
of the route is received.
Indicates how long to advertise invalid routes after they have expired.
If you change any settings in the RIP Configuration screen and clicke on save, the following screen will be
displayed. Click on OK to save your new RIP settings.
030-300432 Rev. A
134
December 2004
User Guide
14. SETTING UP ADVANCED SERVICE CONFIGURATION
You can set up additional Service Configuration options for the Router that allow you to enter the port forwarding
and trigger ports ranges of your choice. Go to Configuration at the homepage menu and select Services.
When you click on define custom service in the Service Configuration screen, the Custom Service screen will
guide you through the steps of creating an advanced NAT service entry via the define custom service button.
NOTE: Westell strongly recommends that you do not change any values in this section. If you experience any
problems, please reset the Router via the external hardware reset button or the procedure defined under the
Maintenance menu.
Port Forwarding Ranges of Ports
Trigger Ports
030-300432 Rev. A
This option allows you to forward a range of WAN ports to an IP address on
the LAN.
This option allows you to forward a range of ports to an IP address on the
LAN only after specific outbound traffic.
135
December 2004
User Guide
14.1 Port Forwarding Ranges of Ports
To select Port Forwarding Ranges of Ports, click on define custom service from the Service Configuration
screen, and then select Port Forwarding Ranges of Ports from the Custom Service screen. Click on Next. The
Port Range screen will be displayed. Enter your values in the Global Port Range fields and click next to continue.
14.2 Adding Port Forwarding Ports
If you made changes in the Port Range screen and clicked on next, the following screen will be displayed. Click on
close to accept the changes, or click on add to go back to Port Range screen and enter additional port range values.
You can repeat this step for each range of ports that you want to add (up to 62 port forwarding ranges). When you
are finished adding ports to the Global Port Range, you must click on close to accept the information you have
entered and return to the Service Configuration screen.
030-300432 Rev. A
136
December 2004
User Guide
Service Name
Type
Protocol
Local IP Address
Base Host Port
The NAT service for which you are configuring Port Forwarding.
The type of NAT service configuration you selected.
The type of Protocol that is used to run this NAT service.
TCP- Transmission Control Protocol.
UDP-User Datagram Protocol (UDP).
If a static IP address has been assigned, it will be displayed here.
The port on the WAN that will host the NAT service selected. Base Host Port is the
first port that will be used for a specific service when configured for a range of ports.
14.3 Port Forwarding Trigger Ports
To select Port Forwarding Trigger Ports, click on define custom service from the Service Configuration screen,
and then select Trigger Ports from the Custom Service screen. Click on next. The follow settings will be displayed
in the Trigger Ports screen. Enter your values in the Local ‘Trigger’ Port Range fields and click on next to
continue.
Service Name
Local Trigger Port Range
Global Port Range
030-300432 Rev. A
The NAT service you selected.
The local LAN side TCP/UDP port.
The WAN side TCP/UDP port range.
137
December 2004
User Guide
14.4 Adding Local Trigger Ports
If you made changes in the Local ‘Trigger’ Port Range screen and clicked next, the following screen will be
displayed. Click on close to accept the changes, or click on add to go back to the Trigger Ports screen and enter
additional port range values. You can repeat this step for each port range that you want to add (up to 10 trigger
ports). When you are finished adding ports to the Local ‘Trigger” Port Range, you must click on close to accept the
information you have entered and to return to the Service Configuration screen.
030-300432 Rev. A
138
December 2004
User Guide
14.5 Static NAT
If you select Services from the Configuration menu, the following screen will be displayed, showing the static
NAT button. Static NAT allows you to configure the Router to work with the special NAT services.
NOTE: When the Router is configured for Static NAT, any unsolicited packets arriving at the WAN would be
forwarded to this device. This feature is used in cases where the user wants to host a server for a specific application.
STOP: Single Static IP must be disabled (if it has been enabled previously) before you enable static NAT. To
disable Single Static IP, select Single Static IP from the Configuration menu. Next, click on the disable button,
and then click on OK in the pop-up screens to allow the Router to be reset. As explained in section 13.1 (Single
Static IP), you must reboot your computer after you enable or disable Single Static IP. After you have rebooted your
computer, return to static NAT configuration screen by selecting Services from the Configuration menu and
clicking on the static NAT button.
030-300432 Rev. A
139
December 2004
User Guide
14.6 Enabling Static NAT
Before you enable static NAT, you must select Default from the Current Profile drop-down box. Static NAT must
be configured for the Router’s default account profile. After you select the default profile, click the static NAT
button.
NOTE: In the following screen, the default account profile is labeled Default. However, if you have renamed the
default account profile, you must select the profile name you created as the default profile.
If you click on the static NAT button in the Service Configuration screen, the following screen will be displayed.
Select your device from the Static NAT Device drop-down arrow, or type the IP address of the device in the field
labeled IP Address. Click on enable. This will automatically enable the Static NAT feature for that device.
030-300432 Rev. A
140
December 2004
User Guide
If you click enable, the following Service Configuration screen will display. Static NAT is now enabled for the
device you selected.
14.7 Disabling Static NAT
If you click on static NAT in the Service Configuration screen, the following screen will be displayed, select a
device name from the Static NAT Device drop-down arrow, or type the IP address of the device in the field labeled
IP Address. Click on disable. This will automatically disable the Static NAT feature for that device.
030-300432 Rev. A
141
December 2004
User Guide
If you click disable, the following Service Configuration screen will be displayed. Static NAT is now disabled for
the device you selected. (No device is displayed in the field adjacent to the static Nat button.)
030-300432 Rev. A
142
December 2004
User Guide
15. MAINTENANCE
15.1 Backup/Restore
The following settings will be displayed if you select Backup/Restore from the Maintenance menu.
NOTE: Backup settings are stored in a separate area of flash, not to an external backup source.
Current configuration becomes
Backup Configuration
Backed up configuration
becomes Current configuration
Factory default becomes
Current configuration
030-300432 Rev. A
Select this button if you want to store all of the current configuration data such
that it can be recalled later.
Select this button if you want to retrieve the last back up copy of all
configuration parameters and make these values current.
Select this button if you want set all user configurable parameters back to the
factory default.
143
December 2004
User Guide
15.2 Firewall Log
The following settings will be displayed if you select Firewall Log from the Maintenance menu.
This screen is an advanced diagnostics screen. It alerts you of noteworthy information sent to the Router from the
Internet. The screen can contain 1000 entries, but a maximum of 50 entries are displayed at a time. Once 1000
entries have been logged, the oldest entry is removed to make space for the new entries as they occur. The following
settings are displayed.
Clear log
Printable/savable format
Settings
Packet
Date
Time
Direction/Source
Rule/Reason
Alert
030-300432 Rev. A
Selecting this button removes all entries from the log.
Selecting this button opens a new window that contains a list of all the logged
packets that can be saved or printed.
Selecting this button opens a new window that contains configuration settings for
selecting the information that you want logged.
The packet number.
The number of days passed since that the packet was sent.
The time that the packet was sent.
The direction of transmission.
The internal rule that caused the logged event. The internal rule is set up under
Firewall rules.
Displays a description of the logged event.
144
December 2004
User Guide
If you clicked on details in the Firewall Log screen, the Packet Details screen will be displayed. Click on close.
To clear the Firewall log, click clear log in the Firewall Log screen. The following pop-up screen will be displayed.
Click OK when asked “Do you wish to clear the Firewall log file?” If you click Cancel, the firewall log will not
be cleared.
To obtain a printable format of the Firewall Log, at the Firewall Log screen, click Printable/Savable Format. This
will allow you to send a copy of the Firewall log to your designated printer.
030-300432 Rev. A
145
December 2004
User Guide
15.3 Administrative Password
The following settings will be displayed if you select Administrative Password from the Maintenance menu.
After you enter your data into the appropriate settings, click on change.
NOTE: If the Router is password protected and you are not an authorized user, you will not be able to change the
values. (The Router cannot be configured unless the user is logged in.) Contact your network administrator for
further instructions.
Enter Administrative Name
NOTE: This changes the Systems Administrator
password not the PPP password.
Enter Administrative Password
Verify Administrative Password
030-300432 Rev. A
Type the name of your network administrative.
Type your network administrator’s password.
Re-type your network administrator’s password.
146
December 2004
User Guide
15.4 Remote Access
The following screen will appear if you select Remote Access from the Maintenance menu. To enable Remote
Access, type in a password and click the enable remote access button.
NOTE: The password should be at least 4 characters long and should not exceed 32 characters. Do not type a blank
space or asterisks in the Password field. The password is also case sensitive.
User Name
Password
Timeout
Disable Timeout
Enable Remote Access
Remote URL
030-300432 Rev. A
Displays your current User Name (Static field)
Field for entering your password
This is time the remote access session can be inactive before it will be disabled. The
Timeout is ignored if Disable Timeout is enabled.
When this checkbox is checked, the remote access timeout will be disabled.
When this checkbox is checked, and you are connected to the internet, remote access
will be enabled. When this checkbox is NOT checked, remote access will be
disabled.
Displays the IP address of the remote management Router.
147
December 2004
User Guide
The following screen shows a check mark in the Enable Remote Access box, and displays a message that the
remote access is currently enabled. After 20 minutes of inactivity, or on reboot, remote access will be automatically
disabled. To disable remote access, click the Enable Remote Access box to uncheck the box. Click apply to save
the settings.
15.5 Update Device
The following screen will be displayed if you click on Update Device from the Maintenance menu. This screen is
used to update the firmware that controls the operation of the Router. The updated firmware may be loaded from
either a file that is located on your PCs hard drive or from update files stored on an Internet server.
NOTE: The configurable settings of your Router may be erased during the update process.
030-300432 Rev. A
148
December 2004
User Guide
Click on the check for web update button in the Update Device screen to check the web for possible software
updates. This screen will retrieve the software update file and display any available update information. You must be
connected to the Internet to use this option.
NOTE: If you click on check for web update and the page returns a “page not found” message, this indicates that the
software update file is not available. Go back to the previous screen to continue.
Click on the web update now button in the Update Device screen to download the software update file and
automatically update the modem firmware if an update is available and applicable. You must be connected to the
Internet to use this option.
030-300432 Rev. A
149
December 2004
User Guide
If you click on the settings button in the Update Device screen, the following screen will appear. This screen
displays the location of the software update file.
Click on the local update now button in the Update Device screen to select the upgrade file from your PC’s hard
drive. This screen allows you to upgrade the software on the Router. Click Browse… and go to the location where
the upgrade file is stored.
NOTE: The actual information displayed in this screen
may vary.
030-300432 Rev. A
150
December 2004
User Guide
Select the appropriate upgrade file from your browser. The file name will appear in the field labeled Upgrade File.
Click on upload file.
This screen shows that the file is being uploaded to the Router.
The screens below show that the file upload has completed and that the Programming Flash is being erased to
prepare the Flash storage area for upload of the new file. (Programming Flash is a temporary storage area for
uploaded files.)
030-300432 Rev. A
151
December 2004
User Guide
The screen below shows that the upload was successful. The Router will not reboot.
The following screen will be displayed as the Router is being reset.
030-300432 Rev. A
152
December 2004
User Guide
After a brief delay, the home page will be displayed. Confirm that you have a DSL sync and that the PPP Status
displays UP. (Click on the reset button to re-establish your PPP session.)
030-300432 Rev. A
153
December 2004
User Guide
16. TROUBLESHOOTING
NOTE: If you are using Models 328W10 or 328W11, options in the Troubleshooting menu may or may not be
displayed depending on the Router’s WAN Configuration (DSLATM PORT or ETHERNET PORT 1). However, all
menu options are displayed if the Router is configured for DSLATM PORT 1. The following sections provide
further details on the Troubleshooting menu.
16.1 System Self Tests
The following settings will be displayed if you select System Self Tests from the Troubleshooting menu.
Click on test all to run a diagnostic test on the Router’s connection.
030-300432 Rev. A
154
December 2004
User Guide
If you want to PING using the System Self Test screen (diagnostics page) shown above, enter your DNS or IP
address in the fields provided and click on the test button. The System Self Test will run a diagnostic test that
executes independent of firewall security settings. See the following table for test descriptions and possible
responses.
If you want to PING using the MS-DOS (shell) window, first you will need to check your firewall security setting.
(If you PING via DOS shell you are susceptible to firewall rules, as this PING is dependent upon the Router's
firewall settings.) If your firewall is set to Medium or High, you will not be able to PING. You must set your
firewall security setting to Low or None.
DSL
Connection/Status
The Router checks the status of the DSL connection.
PPPoE
Possible responses are:
UP: The Router is operating correctly and has obtained synchronization with the
opposing network device.
DOWN: The Router is operating correctly, but has not synchronized with the
opposing device.
Indicates that a PPPoE session is or is not established.
PPP
Possible responses are:
Session UP: A valid PPPoE session has been detected.
No Session: Currently there is no active PPPoE session established.
Initiating Session: A PPP session must be connected from the homepage screen.
Indicates that a PPPoE or PPPoA session must already be established.
Self Test
PING ISP’s Router
DNS
Possible responses are:
Connection UP: The Router has established a connection
No Connection: There is no PPP connection
Initiating Connection: The PPP connection process has been initiated
Connection Halted: A successful PPP connection was halted
Cannot Connect: A PPP connection could not be made because of a PPPoE
session failure.
Authorization Failure: The user name or password is incorrect.
Link Control Protocol Failed: Re-establish the session (from the home page).
Test Description / Test Results
Performs an integrity check of certain internal components of the Router.
Performs an IP network check (i.e., an IP Ping) of the service provider’s Router.
This test verifies that the Router can exchange IP traffic with an entity on the
other side of the DSL line.
Possible responses are:
Success: The Router has detected an IP Remote Router connection.
No Response: The IP Remote Router does not answer the IP Ping.
Could not test: The test could not be executed due to the Router’s settings.
Check your DSL sync or your PPP session. You must have both a DSL sync
and a PPP connection established to execute a PING.
Performs a test to try to resolve the name of a particular host. The host name is
entered in the input box.
Possible responses are:
Success: The Router has successfully obtained the resolved address. The IP
address is shown below the host name input box.
030-300432 Rev. A
155
December 2004
User Guide
IP Address
PING
(via IP Address or Host Name)
Trace
No Response: The Router has failed to obtain the resolved address.
Host not found: The DNS Server was unable to find an address for the given
host name.
No data, enter host name: No host name is specified.
Could not test: The test could not be executed due to the Router’s settings.
Check your DSL sync or your PPP session. You must have both a DSL sync
and a PPP connection established to execute a PING.
IP Address of the Host Name.
Performs an IP connectivity check to a remote computer either within or beyond
the Service Provider’s network. You can PING a remote computer via the IP
address or the DNS address. If your PING fails, try a different IP or DNS
address.
Possible responses are:
Success: The Remote Host computer was detected.
No Response: There was no response to the Ping from the remote computer.
No name or address to PING: No host name or IP address was specified.
Could not test: The test could not be executed due to the Router settings. Check
your DSL sync or your PPP session. You must have both a DSL sync and a PPP
connection established to execute a PING.
Determines the route taken to destination by sending Internet Control Message
Protocol (ICMP) echo packets with varying IP Time-To-Live (TTL) values to
the destination. Trace Route is used to determine where the packet is stopped on
the network.
16.2 Diagnostic Logs
If you select Diagnostic Log, from the System Self Test menu, the following screen will be displayed.
030-300432 Rev. A
156
December 2004
User Guide
To see a list of the log options, click on the arrow at the LOGS drop-down menu. Select an option from the list
provided at the Diagnostics Logs screen.
If you clicked on All, the following screen will be displayed. This screen provides a detailed list of the Router’s
connection status and system information. Click on clear diagnostic log to clear the diagnostic log information.
030-300432 Rev. A
157
December 2004
User Guide
16.2.1 Saving the Diagnostic Log File
If you want to save the diagnostic log file, go to your Browser’s menu bar, and then select File > Save As from the
drop-down menu.
At the Save Web Page dialog box, select a destination for your log file from the Save in drop-down arrow. Next,
enter a name for your log file in the field labeled File name and click on Save.
030-300432 Rev. A
158
December 2004
User Guide
16.3 Statistics
NOTE: If you are using Router Model 328W10 or 328W11 and the Router is configured for ETHERNET PORT 1,
only Ethernet, USB and Wireless statistics will be displayed in the Statistics menu. The DSL Transceiver and the
WAN VC statistics will not be displayed in the Statistics drop-down menu. To access the DSL Transceiver and
WAN VC statistics, you must configure the Router for DSLATM PORT. Refer to section 13.6.3.1 for additional
details.
16.3.1 Ethernet Port Statistics
The following settings will be displayed if you select Statistics > Ethernet from the Troubleshooting menu.
In Errors
In Discard Packets
In Non Unicast Packets
In Unicast Packets
In Octets
030-300432 Rev. A
The number of error packets received on the Ethernet interface.
The number of discarded packets received.
The number of non-Unicast packets received on the Ethernet interface.
The number of Unicast packets received on the Ethernet interface.
The number of bytes received on the Ethernet interface.
159
December 2004
User Guide
Out Errors
Out Discard Packets
Out Non Unicast Packets
Out Unicast Packets
Out Octets
Interface Description
The number of outbound packets that could not be transmitted due to errors.
The number of outbound packets discarded.
The number of non-Unicast packets transmitted on the Ethernet interface.
The number of Unicast packets transmitted on the Ethernet interface.
The number of bytes transmitted on the Ethernet interface.
A description field that refers to the interface type.
16.3.2 DSL Transceiver Statistics
The following settings will be displayed if you select Statistics > DSL Transceiver from the Troubleshooting
menu.
NOTE: If the Router is configured using ETHERNET PORT 1, the following screen will not be available.
Transceiver Revision
Vendor ID Code
Line Mode
The transceiver software version number.
The CPE Vendor’s ID code for their chipset.
The operational mode. Modes supported are No Mode, Multi Mode, T.1413
Mode, G.DMT Mode, and G.LITE Mode.
Data Path
The data path used (either Fast or Interleaved).
Transceiver Information-Down Stream/Up Stream Path
DSL Speed (Kbits/Sec)
The transmission rate that is provided by your Internet Service Provider (ISP).
SNR Margin (db)
The Signal-to-Noise Ratio (S/N) where 0 db = 1x10-7, which inhibits your DSL
speed.
Line Attenuation (dB)
The DSL line loss.
Transmit Power (db/Hz)
The transmitted signal strength.
030-300432 Rev. A
160
December 2004
User Guide
16.3.3 WAN VC Statistics
The following settings will be displayed if you select Statistics > WAN VC from the Troubleshooting menu.
NOTE: If the Router is configured using ETHERNET PORT 1, the following screen will not be available.
VPI/VCI
In Errors
In Discard Packets
In Non Unicast Packets
In Unicast Packets
In Octets
Out Errors
Out Discard Packets
Out Non Unicast Packets
Out Unicast Packets
Out Octets
MTU
Interface Type
Interface Description
030-300432 Rev. A
Displays the VPI/VCI values obtained from your Internet Service Provider.
The number of error packets received on the ATM port.
The number of discarded packets received.
The number of non-Unicast packets received on the ATM port.
The number of Unicast packets received on the ATM port.
The number of bytes received on the ATM port.
The number of outbound packets that could not be transmitted due to errors.
The number of outbound packets discarded.
The number of non-Unicast packets transmitted on the ATM port.
The number of Unicast packets transmitted on the ATM port.
The number of bytes transmitted on the ATM port.
Maximum Transmission Unit -The number of data bytes contained in the ATM frame.
A unique identifier that represents the interface type.
A description field that refers to the interface type.
161
December 2004
User Guide
16.3.4 USB Statistics (Models 7400, 328W10 only)
The following settings will be displayed if you select Statistics > USB from the Troubleshooting menu.
NOTE: If you are using Model 328W10 and the Router is configured using ETHERNET PORT 1, the following
screen will not be available.
USB Port Statistics
The number of times the Host PC reset the USB Interface.
The number of times the Host PC requested communication with the
modem.
NOTE: Data preceded by OUT pertain to transmissions from the Router to a station; the Router is the source. Data
preceded by IN pertain to data received by the Router; the Router is the destination.
The number of packets received that did not have a Multicast or Broadcast
IN-Unicast Packets
class destination IP address.
The number of packets received that had a Multicast or Broadcast class
IN-Non Unicast Packets
destination IP address.
Number of Resets
Number of Isrs
IN Multicast Frames
IN Broadcast Frames
IN Errors
Out-Good Frames
Out-Unicast Packets
Out-Non Unicast Packets
Out-Multicast Frames
Out-Braodcast Frames
Out Errors
030-300432 Rev. A
The number of frames received that had a Multicast class destination IP
address.
The number of frames received that had a Broadcast class destination IP
address.
The number of packets received with an invalid format.
The number of frames sent to the Host PC.
The number of packets sent that did not have a Multicast or Broadcast class
destination IP address.
The number of packets sent that had a Multicast or Broadcast class
destination IP address.
The number of frames sent that had a Multicast class destination IP address.
The number of frames sent that had a Broadcast class destination IP address.
The number of packets received by the modem but not sent to PC due to an
Error condition.
162
December 2004
User Guide
16.3.5 Wireless Statistics (Models 328W10, 328W11 only)
The following settings will be displayed if you select Statistics > Wireless Statistics from the Troubleshooting
menu.
Wireless Card Information
This string, (32 characters or less) is the name associated with the Access
Point (AP). To connect to the AP, the Service Set ID (SSID) on a Station
card must match the SSID on the AP.
This is the Media Access Controller address of the AP. It is used as the Basic
802.11 MAC Address (BSSID)
Service Set Identifier (BSSID).
This is the Network Interface Card Identifier. It uniquely identifies the
FW Version
hardware platform of the AP. This is used with other information to
determine if the inserted card can be used as an AP, and if so, the version of
AP firmware to be used. Not all makes of wireless station cards can be used
as an AP.
Communication Statistics
NOTE: Data listed in the OUT column pertains to transmissions from the AP to a station; the AP is the source. Data
listed in the IN column pertains to data received by the AP; the AP is the destination.
The number of successfully transmitted bytes.
Out-Bytes
The number of successfully transmitted packets.
Out-Packets
The number of packets that did not transmit due to an error.
Out-Errors
The number of successfully received bytes.
In-Bytes
The number of successfully received packets.
In-Packets
The number of received packets with an error.
In-Errors
Network Name (SSID)
030-300432 Rev. A
163
December 2004
User Guide
16.4 Status
NOTE: If you are using Router Model 328W10 or 328W11 and the Router is configured for ETHERNET PORT 1,
the QOS option will not be displayed in the drop-down menu. You must configure the Router for DSLATM PORT
to access QOS in the Advanced WAN drop-down menu. Refer to section 13.6.3.1 for details on enabling and
disabling DSLATM PORT and ETHERNET PORT 1.
16.4.1 LAN Devices
The following settings will be displayed if you select Status > LAN Devices from the Troubleshooting menu.
IP Address
MAC Address
Name
Status
030-300432 Rev. A
Devices on LAN
Displays the IP network address that the Router is on.
Media Access Controller (MAC) address of this device.
Displays the ASCII (text) name of the devices connected to the LAN.
Displays the status of the devices connected to the LAN.
164
December 2004
User Guide
16.4.2 Wireless Stations (Models 328W10, 328W11)
The following settings will be displayed if you select Status > Wireless Stations from the Troubleshooting menu.
NOTE: A Wireless device must be connected to the Router for the fields in this screen to be populated.
Station
MAC Address
030-300432 Rev. A
Wireless Stations List
This number indicates the order in which the stations are first accessed by the Router.
The Media Access Controller Address assigned to the station.
165
December 2004
User Guide
16.4.3 RIP Table
The following settings will be displayed if you select Status > RIP Table from the Troubleshooting menu.
NOTE: RIP must be enabled for this table to be populated.
RIP Network Routing Table
RIP Host Routing Table
Destination
Netmask
Gateway
Metric
030-300432 Rev. A
Indicates Network routes received via RIP.
The Host routes received via RIP.
The destination IP address of the route
The IP mask of the route
The gateway of the route
The RIP metric (0-15). A lower value is better.
166
December 2004
User Guide
16.4.4 QOS Status
The following settings will be displayed if you select Status > QOS from the Troubleshooting menu.
Click on the clear button to clear all counts and statistics (not just latency counts). This does not affect the
configuration values.
IMPORTANT: If you are using Model 328W10 or 328W11 and the Router is configured for ETHERNET PORT 1,
the following screen will not be available.
NOTE: QOS must be enabled on the Router for this table to be populated.
Queue Number
030-300432 Rev. A
Indicates the DiffServ Queue.
Possible responses are:
0 = Best Effort (BE)
1 = Assured Forwarding 1 (AF1)
2 = Assured Forwarding 2 (AF2)
3 = Assured Forwarding 2 (AF3)
4 = Assured Forwarding 2 (AF4)
5 = Expedited Forwarding (EF)
167
December 2004
User Guide
Max Queue Size
Total Dropped Packets
Total Enqueued Packets
Current Depth
Deepest Depth
Queue Number
Peak Info. Rate (%)
Committed Info Rate (%)
Peak Burst (ms)
Committed Burst (ms)
Total Packets Received
Total Marked Packets
Total Filter Packet Drops
Avg. DSL Bytes Per Packet
Avg. Packet Rate Per second
Queue Number
Not Time Stamped
A ms to B ms
6 = Routing Protocols (DiffServ priorities 6 and 7)
The maximum number of packets that can be queued for this priority.
Indicates how many packets of this priority have been dropped by QOS due to
lack of buffer space or filtering rules.
Displays the number of packets, destined for the WAN, that have been received.
Displays the current number of packets of this priority that are queued.
Displays the most number of packets that have been queued at once for this
priority.
QOS Filter Statistics
The DiffServ Queue. (See Queue Number description above.)
The maximum allowed rate for this priority, expressed as a percentage of the
DSL rate.
The committed rate for this priority, expressed as a percentage of the DSL rate
Displays the interval in milliseconds for averaging the peak offered rate.
Displays the interval in milliseconds for averaging the committed offered rate.
Displays the total number of packets of this priority that are destined for the
LAN.
Displays the number of packets of this priority that exceeded the committed rate,
but not the peak rate, and were marked with a higher drop priority
Displays the number of packets of this priority that exceeded the peak rate and
that were, therefore, dropped.
Displays the average size of packets for this priority, including all overhead.
Displays the average rate (in packets per seconds) for this priority.
QOS Latency Counts
The DiffServ Queue. (See Queue Number description above.)
The packets with no incoming time stamp. (Often these are generated internal to
the modem.)
The number of packets of this priority whose time in the modem fell between A
and B milliseconds. (Time is measured from the point the packet arrives at the
modem’s processor until is passed to the ATM hardware for transmission.)
Possible ranges are (A ms to B ms):
0 ms to 10 ms
10 ms to 20 ms
20 ms to 40 ms
40 ms to 100 ms
100 ms to 1000 ms
1000 ms to 3000 ms
Larger than 3000 ms
030-300432 Rev. A
168
December 2004
User Guide
16.4.5 VOIP Status
The following settings will be displayed if you select Status > VOIP from the Troubleshooting menu.
NOTE: A VOIP device must be connected to the Router for this table to be populated.
URI
Local IP Address
Expiration
030-300432 Rev. A
SIP Registry Information
The SIP URI that is trying to register. (This field only indicates that a SIP device
tried to register, not that it succeeded.)
The local, LAN IP address of the SIP device.
Indicates the expiration (in seconds) of the registered SIP URI.
169
December 2004
User Guide
17. NAT SERVICES
For your convenience, the Router supports protocols for Applications, Games, and VPN-specific programs. The
following chart provides protocol information for the services supported by the Router.
NOTE: To configure the Router for a service or application, follow the steps in section 14 (Setting Up Advanced
Service Configuration) of this User Guide.
Application/Game
Aliens vs. Predator
America Online
AoE II: Conquors
AOL Instant Messenger
Asheron's Call
Battlecom
Black and White
Blizzard Battle.net (Diablo II)
Buddy Phone
Bungie.net, Myth, Myth II Server
Calista IP Phone
Citrix Metaframe
Client POP/IMAP
Client SMTP
Counter Strike
Dark Reign 2
Delta Force ( Client and Server )
Delta Force 2
DeltaForce: Land Warrior
DNS
Elite Force
Everquest
F-16, Mig 29
F-22 Lightning 3
F-22 Raptor
Fighter Ace II
Fighter Ace II for DX play
030-300432 Rev. A
Applications/Games/VPN Support
Port/Protocol
80 UDP, 2300 UDP, 8000-8999 UDP
5190 TCP/UDP
47624 TCP/UDP, 6073 TCP/UDP, 2300-2400 TCP/UDP
4099 TCP, 5190 TCP
9000-9013 UDP, 28800-29000 TCP
2300-2400 TCP/UDP, 47624 TCP/UDP
2611-2612 TCP, 6667 TCP, 6500 UDP, 27900 UDP
4000 TCP, 6112 TCP/UDP
700, 701 UDP
3453 TCP
3000 UDP, 5190 TCP
1494 TCP
110 TCP
25 TCP
27015 TCP/UDP, 27016 TCP/UDP
26214 TCP/UDP
3568 UDP, 3100-3999 TCP/UDP
3568-3569 UDP
UDP 53
TCP 21
TCP 7430
TCP 80
UDP 1029
UDP 1144
UDP 65436
UDP 17478
53 UDP
2600 UDP, 27500 UDP, 27910 UDP, 27960 UDP
1024-7000 TCP/UDP
3863 UDP
4660-4670 TCP/UDP, 3875 UDP, 4533-4534 UDP, 4660-4670 UDP
3874-3875 UDP
50000-50100 TCP/UDP
50000-50100 TCP/UDP, 47624 TCP, 2300-2400 TCP/UDP
170
December 2004
User Guide
Application/Game
FTP
GameSpy Online
Ghost Recon
GNUtella
Half Life Server
Heretic II Server
Hexen II
Hotline Server
HTTPS
ICMP Echo
ICQ OLD
ICQ 2001b
ICUII Client
ICUII Client Version 4.xx
IMAP
IMAP v.3
Internet Phone
IPSEC ESP
IPSEC IKE
Ivisit
KALI, Doom & Doom II
KaZaA
Limewire
Medal Of Honor: Allied Assault
mIRC Chat
030-300432 Rev. A
Port/Protocol
20 TCP, 21 TCP
UDP 3783
UDP 6515
TCP 6667
UDP 12203
TCP/UDP 13139
UDP 27900
UDP 28900
UDP 29900
UDP 29901
TCP 80
UDP 1038
UDP 1032
UDP 53
UDP 2347
UDP 2346
6346 TCP/UDP, 1214 TCP
27005 UDP(client only)
27015 UDP
28910 TCP
26900 (+1) each player needs their own port. Increment by one for each
person
5500, 5503 TCP 5499 UDP
443 TCP/UDP
4 ICMP
4000 UDP, 20000-20019 TCP
4099 TCP, 5190 TCP
2000-2038 TCP, 2050-2051 TCP, 2069 TCP, 2085 TCP, 3010-3030 TCP
1024-5000 TCP, 2050-2051 TCP, 2069 TCP, 2085 TCP, 3010-3030 TCP,
2000-2038 TCP6700-6702 TCP, 6880 TCP, 1200-16090 TCP
119 TCP/UDP
220 TCP/UDP
22555 UDP
PROTOCOL 50
500 UDP
9943 UDP, 56768 UDP
2213 UDP, 6666 UDP (EACH PC USING KALI MUST USE A
DIFFERENT PORT NUMBER STARTING WITH 2213 + 1
1214 TCP/UDP
6346 TCP/UDP, 1214 TCP
TCP 80
UDP 53
UDP 2093
UDP 12201
TCP 12300
UDP 2135
UDP 2139
TCP/UDP 28900
6660-6669 TCP
171
December 2004
User Guide
Application/Game
Motorhead Server
MSN Game Zone
MSN Game Zone (DX 7 & 8 play)
MSN Messenger
Napster
Need for Speed 3, Hot Pursuit
Need for Speed, Porsche
Net2Phone
NNTP
Operation FlashPoint
Outlaws
Pal Talk
pcAnywhere host
Phone Free
Quake 2
Quake 3
Quicktime 4/Real Audio
Rainbow Six & Rogue Spear
RealOne Player
Real Audio
Roger Wilco
ShoutCast Server
SSH Secure Shell
Starcraft
Starfleet Command
Telnet
Tiberian Sun & Dune 2000
Ultima Online
Unreal Tournament server
030-300432 Rev. A
Port/Protocol
16000 TCP/UDP, 16010-16030 TCP/UDP
6667 TCP, 28800-29000 TCP
6667 TCP, 6073 TCP, 28800-29000 TCP, 47624 TCP, 2300-2400
TCP/UDP
6891-6900 TCP, 1863 TCP/UDP, 5190 UDP, 6901 TCP/UDP
6699 TCP
1030 TCP
9442 UDP
6801 UDP
119 TCP/UDP
47624 UDP, 6073 UDP, 2300-2400 TCP/UDP, 2234 TCP
5310 TCP/UDP
2090-2091 TCP/UDP, 2095 TCP, 5001 TCP, 8200-8700 TCP/UDP, 10252500 UDP
5631 TCP, 5632 UDP, 22 UDP
1034-1035 TCP/UDP, 9900-9901 UDP, 2644 TCP, 8000 TCP
27910 UDP
27660 UDP
Each computer playing QuakeIII must use a different port number, starting
at 27660 and incrementing by 1. You'll also need to do the following:
1. Right click on the QIII icon
2. Choose "Properties"
3. In the Target field you'll see a line like "C:\Program Files\Quake III
Arena\quake3.exe"
4. Add the Quake III net_port command to specify a unique
communication port for each system. The complete field should look like
this: "C:\Program
Files\Quake III Arena\quake3.exe" +set
net_port 27660
5. Click OK.
6. Repeat for each system behind the NAT, adding one to the net_port
selected (27660,27661,27662)
6970-32000 UDP, 554 TCP/UDP
2346 TCP
TCP - 554, 7070 to 7071
UDP - 6970 to 7170
6970-7170 UDP
TCP/UDP 3782
UDP 3783 (BaseStation)
8000-8005 TCP
22 TCP/UDP
2346 TCP
2300-2400 TCP/UDP, 47624 TCP/UDP
23 TCP
1140-1234, 4000 TCP/UDP
5001-5010 TCP, 7775-7777 TCP, 8800-8900 TCP, 9999 UDP, 7875 UDP
7777 (default gameplay port)
7778 (server query port
7779,7779+ are allocated dynamically for each helper UdpLink objects,
172
December 2004
User Guide
Application/Game
USENET News Service
VNC, Virtual Network Computing
Westwood Online, C&C
World Wide Web (HTTP)
XBOX Live
Yahoo Messenger Chat
Yahoo Messenger Phone
VPN Protocol
IPSec Encryption
L2TP
PPTP
030-300432 Rev. A
Port/Protocol
including UdpServerUplin objects. Try starting with 7779-7781 and add
ports if needed
27900 server query, if master server uplink is enabled. Home master
servers use other ports like 27500
Port 8080 is for UT Server Admin. In the [UWeb.WebServer] section of
the server.ini file, set the ListenPort to 8080 and ServerName to the IP
assigned to the Router from your ISP.
143 TCP
5500 TCP, 5800 TCP, 5900 TCP
4000 TCP/UDP, 1140-1234 TCP/UDP
80 TCP
443 TCP (SSL)
8008 OR 8080 TCP (PROXY)
TCP/UDP 88 and 3074
5000-5001 TCP
5055 UDP
Comments
IPSec using AH can not be supported through NAT. IPSec using ESP and
L2TP can be supported via an ALG
IPSec using ESP and L2TP can be supported via an ALG.
Works through NAT.
173
December 2004
User Guide
18. TECHNICAL SUPPORT INFORMATION
Westell Technical Support
If technical assistance is required, contact your Internet service provider for support. By using one of the following
options:
North America
Phone: 1-630-375-4900
U.K./Europe
Phone: (44) 01256 843311
Visit Westell at www.Westell.com to view frequently asked questions and enter on-line service requests, or send
email to global_support@westell.com to obtain additional information.
19. WARRANTY AND REPAIRS
Warranty
Westell warrants this product free from defects at the time of shipment. Westell also warrants this product fully
functional for the period specified by the terms of the warranty. Any attempt to repair or modify the equipment by
anyone other than an authorized representative will void the warranty.
Repairs
Westell will repair any defective Westell equipment without cost during the warranty period if the unit is defective
for any reason other than abuse, improper use, or improper installation, or acts of nature. Before returning the
defective equipment, request a Return Material Authorization (RMA) number from Westell. An RMA number
must be quoted on all returns. When requesting an RMA, please provide the following information:
•
•
•
•
•
•
Product model number (on product base)
Product serial number (on product base)
Customer ship-to address
Contact name
Problem description
Purchase date
After an RMA number is obtained, return the defective unit, freight prepaid, along with a brief description of the
problem to one of the following options:
U.K./Europe
Westell, Ltd.
Ringway House
Bell Road
Daneshill
Basingstoke
RG24 8FB
United Kingdom
North America
Westell, Inc.
ATTN: R.G.M Department
750 N. Commons Drive
Aurora, IL 60504-7940 USA
Westell will continue to repair faulty equipment beyond the warranty period for a nominal charge. Contact a Westell
Technical Support Representative for details.
030-300432 Rev. A
174
December 2004
User Guide
20. SOFTWARE LICENSE AGREEMENT
READ THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT CAREFULLY. THIS
SOFTWARE IS COPYRIGHTED AND LICENSED (NOT SOLD). BY INSTALLING AND OPERATING
THIS PRODUCT, YOU ARE ACCEPTING AND AGREEING TO THE TERMS OF THIS LICENSE
AGREEMENT. IF YOU ARE NOT WILLING TO BE BOUND BY THE TERMS OF THIS LICENSE
AGREEMENT, YOU SHOULD PROMPTLY RETURN THE SOFTWARE AND HARDWARE TO
WESTELL TECHNOLOGIES, INC. THIS LICENSE AGREEMENT REPRESENTS THE ENTIRE
AGREEMENT CONCERNING THE SOFTWARE BETWEEN YOU AND WESTELL TECHNOLOGIES,
INC. (REFERRED TO AS "LICENSOR"), AND IT SUPERSEDES ANY PRIOR PROPOSAL,
REPRESENTATION, OR UNDERSTANDING BETWEEN THE PARTIES.
1. License Grant. Licensor hereby grants to you, and you accept, a nonexclusive license to use the Compact
Disk (CD) and the computer programs contained therein in machine-readable, object code form only
(collectively referred to as the "SOFTWARE"), and the accompanying User Documentation, only as
authorized in this License Agreement. The SOFTWARE may be used only in connection with the number of
systems for which you have paid license fees as dictated in your support agreement. You agree that you will
not assign, sublicense, transfer, pledge, lease, rent, or share your rights under this License Agreement. You
agree that you may not nor allow others to reverse assemble, reverse compile, or otherwise translate the
SOFTWARE.
You may retain the SOFTWARE CD for backup purposes only. In addition, you may make one copy of the
SOFTWARE in any storage medium for backup purposes only. You may make one copy of the User's
Manual for backup purposes only. Any such copies of the SOFTWARE or the User's Manual shall include
Licensor's copyright and other proprietary notices. Except as authorized under this paragraph, no copies of
the SOFTWARE or any portions thereof may be made by you or any person under your authority or control.
2. Licensor's Rights. You acknowledge and agree that the SOFTWARE and the User's Manual are
proprietary products of Licensor protected under U.S. copyright law. You further acknowledge and agree
that all right, title, and interest in and to the SOFTWARE, including associated intellectual property rights,
are and shall remain with Licensor. This License Agreement does not convey to you an interest in or to the
SOFTWARE, but only a limited right of use revocable in accordance with the terms of this License
Agreement.
3. License Fees. The fees paid by you under the support agreement are paid in consideration of the licenses
granted under this License Agreement.
4. Term. This License Agreement is effective upon your opening of this package and shall continue until
terminated. You may terminate this License Agreement at any time by returning the SOFTWARE and all
copies thereof and extracts there from to Licensor. Licensor may terminate this License Agreement upon the
breach by you of any term hereof. Upon such termination by Licensor, you agree to return to Licensor the
SOFTWARE and all copies and portions thereof.
5. Limited Warranty. Licensor warrants, for your benefit alone, for a period of 90 days from the date of
commencement of this License Agreement (referred to as the "Warranty Period") that the SOFTWARE CD
in which the SOFTWARE is contained are free from defects in material and workmanship. Licensor further
warrants, for your benefit alone, that during the Warranty Period the SOFTWARE shall operate
substantially in accordance with the functional specifications in the User's Manual. If during the Warranty
Period, a defect in the SOFTWARE appears, you may return the SOFTWARE to Licensor for replacement.
You agree that the foregoing constitutes your sole and exclusive remedy for breach by Licensor of any
warranties made under this Agreement.
030-300432 Rev. A
175
December 2004
User Guide
EXCEPT FOR THE WARRANTIES SET FORTH ABOVE, THE SOFTWARE CD, AND THE
SOFTWARE CONTAINED THEREIN, ARE LICENSED "AS IS," AND LICENSOR DISCLAIMS ANY
AND ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
6. Limitation of Liability. Licensor's cumulative liability to you or any other party for any loss or damages
resulting from any claims, demands, or actions arising out of or relating to this Agreement shall not exceed
the license fee paid to Licensor for the use of the SOFTWARE. In no event shall Licensor be liable for any
indirect, incidental, consequential, special, or exemplary damages or lost profits, even if Licensor has been
advised of the possibility of such damages. SOME STATES DO NOT ALLOW THE LIMITATION OR
EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
7. Governing Law. This License Agreement shall be construed and governed in accordance with the laws of
the State of Illinois. You submit to the jurisdiction of the state and federal courts of the state of Illinois and
agree that venue is proper in those courts with regard to any litigation arising under this Agreement.
8. Costs of Litigation. If any action is brought by either party to this License Agreement against the other
party regarding the subject matter hereof, the prevailing party shall be entitled to recover, in addition to any
other relief granted, reasonable attorney fees and expenses of litigation.
9. Severability. Should any term of this License Agreement be declared void or unenforceable by any court of
competent jurisdiction, such declaration shall have no effect on the remaining terms hereof.
10. No Waiver. The failure of either party to enforce any rights granted hereunder or to take action against
the other party in the event of any breach hereunder shall not be deemed a waiver by that party as to
subsequent enforcement of rights or subsequent actions in the event of future breaches.
030-300432 Rev. A
176
December 2004
User Guide
21. PUBLICATION INFORMATION
Westell® Router (Models 7400, 7401, 328W10, 328W11)
User Guide Part Number 030-300432 Rev. A
Copyright © 2004 Westell, Inc.
All rights reserved.
Westell, Inc.
750 North Commons Drive
Aurora, Illinois 60504 USA
www.westell.com
All trademarks and registered trademarks are the property of their respective owners.
030-300432 Rev. A
177
December 2004

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 67
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:8add49c0-787b-483b-b4c4-8ab55d113ca2
Modify Date                     : 2005:03:31 14:15:16-08:00
Create Date                     : 2005:03:31 14:15:05-08:00
Metadata Date                   : 2005:03:31 14:15:16-08:00
Document ID                     : uuid:20cf7a6c-a4f6-4d07-9765-6d798aed2502
Format                          : application/pdf
Title                           : PRODUCT DESCRIPTION
Creator                         : Acrobat PDFMaker 5.0 for Word
Author                          : SAllen
Producer                        : Acrobat Distiller 5.0.5 (Windows)

EXIF Metadata provided by EXIF.tools