XAC Automation RP10 PINPAD User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3614783
Application ID	kbEYngjMdjqgsYNgI4QdUg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	41.72kB (521463 bits)
Date Submitted	2017-10-24 00:00:00
Date Available	2018-04-23 00:00:00
Creation Date	2017-10-16 20:00:10
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2017-10-16 20:00:10
Document Title	Microsoft Word - VU1-228-170526 Installation Guide_RP-10_draft for PCI _1_ 20171016
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ninlin

RTO
OS PAYME
ENT DEVICE
RP-1
10
INSTTALLATIO
ON GUIDE
1. PACKAGE CONTENT
„
„
RP-10
Privacy Shield
(Optional)
2. DEVICE OVERVIEW
RP‐10 Key Buttons & Interface Ports (Figure 1):
FRONT
REAR
Figure 1
FRONT AREA
REAR AREA
2.4” Display
Rubber Keypad
Magnetic Strip Reader (MSR) slot
Smart Card Reader (SCR) slot
USB cable (type A)
Battery Compartment
■ RP-10 power spec:
Input: 5V DC, 0.5A
„ Operating Temperature: 0 C to 40 C
3. POWER ON/OFF THE DEVICE
To power on the device, please plug the USB cable into the USB port of your host terminal or
POS.
Note: When there is no action on RP‐10 after 60 seconds, the device will enter power saving
mode. Please short press any button on keypad to wake up the device.
4. USING THE MAGNETIC CARD READER
Swipe the card through the slot with magnetic stripe side facing the same direction as the
display. (Figure 3)
Figure 3
5. USING THE IC CARD READER
Insert an IC card into the slot (Figure 4) with the chip side facing the same direction as the
touch panel (Figure 5).
Figure 4
Figure 5
6. USING THE KEY PAD
After inserting the chip card, Press the numeric key as below keypad (Figure 6) to enter the
desirable numbers. Press Cancel (X) key to terminate any current function and press the Enter
(O) key to confirm a value or an option.
Figure 6
7. USING THE CONTACTLESS CARD READER
Tap the contactless card on top of the contactless logo (Figure 7).
Figure 7
9. INSERT SIM & SAM CARD
After removing the battery cover, the user can find SAM *2 slots at the bottom side of device.
Please insert the card correctly as the icon shown on the cover:
Figure 10
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
Note: The country code selection is for non-US model only and is not available to all US model. Per
FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.
XAC Automation Corporation
886-3-577-2738
The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be
disclosed, distributed or reproduced without permission of XAC Automation Corporation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2017:10:16 20:00:10+08:00
Create Date                     : 2017:10:16 20:00:10+08:00
Format                          : application/pdf
Title                           : Microsoft Word - VU1-228-170526 Installation Guide_RP-10_draft for PCI _1_  20171016
Creator                         : ninlin
Document ID                     : uuid:86b7a0ba-00ca-4e20-a0e0-2b79f499b69c
Instance ID                     : uuid:bb3830f2-7ed6-4233-9d6d-b8a07e7727fb
Page Count                      : 6
Author                          : ninlin

EXIF Metadata provided by EXIF.tools