Yaesu Musen 20575X50 HF / VHF / UHF All Mode Transceiver User Manual 05 1 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2440474
Application ID	XT0U74oL01ckNxQiV1w87A==
Document Description	Users Manual Part 1 Rev 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	338.44kB (4230558 bits)
Date Submitted	2014-11-11 00:00:00
Date Available	2014-11-11 00:00:00
Creation Date	2014-10-23 16:34:37
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2014-10-23 16:34:37
Document Title	05_1_User_Manual.pdf
Document Creator	Adobe InDesign CS6 (Windows)
Document Author:	YAESU MUSEN CO., LTD.

HF/VHF/UHF All Mode Transceiver
FT-991
Operating Manual
YAESU MUSEN CO., LTD.
Tennozu Parkside Building
2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan
YAESU USA
6125 Phyllis Drive, Cypress, CA 90630, U.S.A.
YAESU UK
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
Table of Contents
Table of Contents.......................................................... 1
Accessories & Options.................................................. 3
Supplied Accessories................................................. 3
Available Options...................................................... 4
Adjusting the Clock................................................... 5
Resetting the Microprocessor.................................... 5
Installation and Interconnections................................ 6
Antenna Considerations............................................ 6
About Coaxial Cable................................................. 6
Grounding.................................................................. 7
Connection of Antenna and Power Cables................ 8
Connection of Microphone and Headphone.............. 9
Key, Keyer, and Computer-Driven Keying
Interconnections...................................................... 10
VL-1000 Linear Amplifier Interconnections........... 11
Interfacing to Other Linear Amplifiers.................... 12
Front Panel Controls & Switches.............................. 13
Display Indications..................................................... 18
Rear Panel.................................................................... 21
MH-31A8J Microphone Switches.............................. 23
Optional FH-2 Switches.............................................. 24
Basic Operation: Receiving on Amateur Bands....... 25
Operation on 60-Meter (5 MHz) Band (U.S. version
only)........................................................................ 28
CLAR (Clarifier) Operation.................................... 29
LOCK...................................................................... 30
DIMMER................................................................ 30
VFO COLOR.......................................................... 30
Band Stack Operation.............................................. 31
C.S (Custom Switch)............................................... 31
Convenience Features................................................. 31
SCOPE.................................................................... 32
More Frequency Navigation Techniques................ 33
Receiver Operation (Front End Block Diagram).... 34
ATT (Attenuator)................................................... 35
Interference Rejection................................................ 35
IPO (Intercept Point Optimization)......................... 36
IF Noise Blanker (NB) Operation........................... 37
CONTOUR Control Operation............................... 38
IF SHIFT Operation (SSB/CW/RTTY/PKT
Modes)..................................................................... 39
FT-991 Operating Manual
WIDTH (IF DSP Bandwidth) Tuning (SSB/CW/
RTTY/DATA Modes).............................................. 40
NARROW (NAR) One-Touch IF Filter
Selection.................................................................. 41
IF NOTCH Filter Operation (SSB/CW/RTTY/
DATA/AM Modes).................................................. 42
Digital NOTCH Filter (DNF) Operation................. 43
Digital Noise Reduction (DNR) Operation............. 43
Tools for Comfortable and Effective Reception....... 44
RF Gain................................................................... 44
Audio Peak Filter.................................................... 45
AGC (Automatic Gain Control).............................. 46
Adjustable Receiver Audio Filter............................ 47
SSB/AM Mode Transmission..................................... 48
ATU Operation........................................................ 50
Using the Automatic Antenna Tuner......................... 50
About ATU Operation............................................. 51
Parametric Microphone Equalizer (SSB/AM/FM
mode)....................................................................... 52
Enhancing Transmit Signal Quality.......................... 52
Using the Speech Processor (SSB Mode)............... 54
Adjusting the SSB Transmitted Bandwidth (SSB
Mode)...................................................................... 55
Voice Memory (SSB/AM/FM modes: Requires
optional DVS-6 and FH-2)................................. 56
Transmitter Convenience Features........................... 56
VOX (SSB/AM/FM Modes: Automatic TX/RX
Switching using Voice Control).............................. 58
MONITOR (SSB/AM/FM modes).......................... 59
Split-Frequency Operation...................................... 60
Setup for Straight Key (and Straight Key emulation)
Operation................................................................. 61
CW Mode Operation.................................................. 61
Using the Built-in Electronic Keyer........................ 62
CW Spotting (Zero-Beating)................................... 65
CW Convenience Features......................................... 65
CW Delay Time Setting.......................................... 66
Contest Memory Keyer (Using the Optional FH-2
Remote Control Keypad)........................................ 67
Basic Operation....................................................... 72
Page 1
Table of Contents
FM Mode Operation................................................... 72
Repeater Operation.................................................. 73
Tone Squelch Operation.......................................... 74
Memory Operation..................................................... 75
Convenient Memory functions................................ 75
QMB (Quick Memory Bank).................................. 75
Standard Memory Operation................................... 76
Memory Groups...................................................... 80
Operation on Alaska Emergency Frequency: 5167.5
khz (U.S. Version Only).............................................. 81
VFO and Memory Scanning...................................... 82
VFO Scanning......................................................... 82
Memory Scan.......................................................... 83
PMS (Programmable Memory Scanning)................ 84
RTTY (Radio Teletype) Operation............................ 85
Example of Connecting RTTY Communications
Device...................................................................... 85
DATA (PSK) Operation.............................................. 86
Example of Data Communications Device ............ 86
Menu Mode.................................................................. 87
Specifications............................................................... 91
Page 2
FT-991 Operating Manual
Accessories & Options
Hand Microphone (MH-31A8J)
1 pc
DC Power Cord			
1 pc
Spare Fuse (25A)			1 pc
Operating Manual		
1 pc
Warranty Card			
1 pc
FT-991 Operating Manual
Supplied Accessories
A07890001
T9025225
Q0000074
Page 3
Accessories & Options
MD-200A8X
MD-100A8X
YH-77STA
FH-2
VL-1000/VP-1000
FC-40
FP-1030A
CT-118
CT-39A
CT Cable (MDIN10P - Bare Wire 2m)
MD-200A8X
VL-1000/VP-1000
Page 4
Available Options
Ultra-High-Fidelity Desktop Microphone
Desktop Microphone
Lightweight Stereo Headphone
Remote Control Keypad
Linear Amplifier/AC Power Supply
External Automatic Antenna Tuner
External Power Supply (13.8 VDC 25 A)
VL-1000 Linear Amplifier Connection Cable
Packet Interface Cable
Linear Amplifier Connection Cable (P/N T9207451)
YH-77STA
FH-2
FC-40
FT-991 Operating Manual
Before You Begin
Adjusting the Clock
Use the following procedure to adjust the clock shown at the top right of the LCD display.
1. Press and hold the MENU(SETUP) button.
2. Touch [TIME/DATE] on the LCD.
3. Enter the present time with the number keys on the
LCD, then touch [ENT].
4. Touch [DATE] on the LCD to switch the screen.
5. Enter month, day, and year with the number keys on
the LCD, then touch [ENT].
6. Touch [BACK] on the LCD to return to the setup
mode display.
7. Press the MENU(SETUP) button to return to the
radio operation display.
MENU(SETUP) button
LCD
Resetting the Microprocessor
Resetting Memories (Only)
Use this procedure to reset (clear) the previously stored
Memory channels, without affecting any configuration
changes you may have made to the Menu settings.
1. Press the front panel ON/OFF switch to turn the
transceiver off.
2. While holding the AM button in, press and hold
in the front panel ON/OFF switch to turn the transceiver on. Once the transceiver comes on, you may
release the buttons.
ON/OFF switch
AM button
Menu Resetting
Use this procedure to restore the Menu settings to their
factory defaults, without affecting the memories you
have programmed.
1. Press the front panel ON/OFF switch to turn the
transceiver off.
2. While holding the MENU(SETUP) button in, press
and hold in the front panel ON/OFF switch to turn
the transceiver on. Once the transceiver comes on,
you may release the buttons.
ON/OFF switch
MENU(SETUP) button
Full Reset
Use this procedure to restore all Menu and Memory settings to their original factory defaults. All Memories will
be cleared by this procedure.
1. Press the front panel ON/OFF switch to turn the
transceiver off.
2. While holding the FAST and LOCK buttons in,
press and hold in the front panel ON/OFF switch to
turn the transceiver on. Once the transceiver comes
on, you may release the buttons.
FT-991 Operating Manual
FAST button
ON/OFF switch
LOCK button
Page 5
Installation and Interconnections
Antenna Considerations
The FT-991 is designed for use with any antenna system providing a 50 Ohm resistive impedance at the desired operating frequency. While minor excursions from the 50-Ohm specification are of no consequence, if the Standing Wave Ratio (SWR) present at the Antenna jack is greater than 3:1, the transceiver’s Automatic Antenna Tuner may not be able to
reduce the impedance mismatch to an acceptable value.
Every effort should be made to ensure that the impedance of the antenna system be as close as possible to the specified
50-Ohm value. Note that the “G5RV” type antenna does not provide a 50-Ohm impedance on all HF Amateur bands. An
external wide-range antenna coupler must be used with this antenna type.
Any antenna to be used with the FT-991 must be fed from the transceiver with 50 Ohm coaxial cable. Therefore, when
using a “balanced” antenna such as a dipole, remember that a balun or other matching/balancing device must be used to
ensure proper antenna performance.
The same precautions apply to any additional (receive-only) antennas connected to the antenna jacks. if your receiveonly antennas do not have impedance near 50 Ohms at the operating frequency, you may need to install an external antenna tuner to obtain optimum performance.
About Coaxial Cable
Use high-quality 50-Ohm coaxial cable for the lead-in to your FT-991 transceiver. All efforts at providing an efficient
antenna system will be wasted if poor quality, lossy coaxial cable is used. This transceiver utilizes standard “M” (“PL259”) type connectors.
Typical PL-259 Installation
Page 6
FT-991 Operating Manual
Installation and Interconnections
Grounding
The FT-991 transceiver, like any other HF communications apparatus, requires an effective ground system for maximum electrical safety and best communications effectiveness. A good ground system can contribute to station efficiency
in a number of ways:
 It can minimize the possibility of electrical shock to the operator.
 It can minimize RF currents flowing on the shield of the coaxial cable and the chassis of the transceiver. such currents may lead to radiation, which can cause interference to home entertainment devices or laboratory test equipment.
 It can minimize the possibility of erratic transceiver/accessory operation caused by RF feedback and/or improper
current flow through logic devices.
An effective earth ground system may take several forms. for a more complete discussion, see an appropriate RF engineering text. The information below is intended only as a guideline.
Typically, the ground connection consists of one or more copper-clad steel rods, driven into the ground. If multiple
ground rods are used, they should be positioned in a “V” configuration and bonded together at the base of the “V” which
is nearest the station location. Use a heavy, braided cable (such as the discarded shield from type RG-213 coaxial cable)
and strong cable clamps to secure the braided cable(s) to the ground rods. Be sure to weatherproof the connections
to ensure many years of reliable service. Use the same type of heavy, braided cable for the connections to the station
ground bus (described below).
Inside the station, a common ground bus consisting of a copper pipe of at least 25 mm diameter should be used. An alternative station ground bus may consist of a wide copper plate (single-sided circuit board material is ideal) secured to
the bottom of the operating desk. Grounding connections from individual transceivers, power supplies, and data communications devices (TNCs, etc.) should be made directly to the ground bus using a heavy, braided cable.
Do not “Daisy-Chain” ground connections from one electrical device to another and thence to the ground bus. This
method may nullify any attempt at effective radio frequency grounding. See the drawing below for examples of proper
grounding techniques.
Inspect the ground system - inside the station as well as outside - on a regular basis to ensure continued performance
and safety.
Besides following the above guidelines carefully, note that household or industrial gas lines must never be used in an
attempt to establish an electrical ground. Cold water pipes may, in some instances, help in the grounding effort, but gas
lines represent a significant explosion hazard, and must never be used.
Transceiver LinearLinear
Transceiver
Amplifier
Amplifier
GND
GND
GND
Transceiver LinearLinear
Transceiver
Amplifier
Amplifier
TNC TNC
GND
GND
GND
GND
GND
GND
TNC TNC
GND
GND
GND
"Daisy Chain"
"Daisy Chain"
Proper Ground Connection
FT-991 Operating Manual
Improper Ground Connection
Page 7
Installation and Interconnections
Connection of Antenna and Power Cables
Please follow the outline in the illustration regarding the proper connection of antenna coaxial cables, as well as the DC
power cable. The DC power connector for the FT-991 must only be connected to a DC source providing 13.8 Volts DC (±10
%), and capable of at least 23 Amperes of current. Always observe proper polarity when making DC connection:
The RED DC power lead connects to the Positive (+) DC terminal.
The BLACK DC power lead connects to the Negative (–) DC terminal.
To prevent damage from
lightning, atmospheric electricity, electrical shock etc., please
provide a good earth ground.
Use a short,
thick, braided
cable to connect your station
equipment to the
buried ground rod (or alternative earth
ground system).
Check the DC voltage and current rating
(+13.8 V, 23 A) of the power
supply before connecting to the
transceiver.
We recommend the use of the FP-1030A (USA market only) AC Power Supply. Other models of power supplies may
be used with the FT-991, but the 13.8 VDC input voltage, 23 Ampere current capability, and DC cable polarity guidelines described above must be strictly followed.
Note that other manufacturers may use the same type of DC power connections as does your FT-991 transceiver, however, the wiring configuration may be different from that specified for your transceiver. Serious damage can be caused if
improper DC connections are made; consult with a qualified service technician when in doubt.
The 100 V RF voltage (@100 W/50-ohm) is applied to the TX RF section of the transceiver while transmitting.
Do not touch the TX RF section absolutely while transmitting.
Permanent damage can result when improper supply voltage, or reverse-polarity voltage, is applied to the FT991. The Limited Warranty on this transceiver does not cover damage caused by application of AC voltage, reverse polarity DC, or DC voltage outside the specified range of 13.8 V ±10 %. When replacing fuses, be certain to use a
fuse of the proper rating. The FT-991 requires a 25 A blade fuse.
Advice:
 Do not position the FT-991 in a location with direct exposure to sunshine.
 Do not position the FT-991 in a location exposed to dust and/or high humidity.
 Ensure adequate ventilation around the FT-991, to prevent heat build-up and possible reduction of performance due
to high heat.
 Do not install the FT-991 on an unstable desk or table. Do not place in a location where objects may fall onto it from above.
 To minimize the possibility of interference to home entertainment devices, take all precautionary steps including
separation of TV/FM antennas from Amateur transmitting antennas to the greatest extent possible, and keep transmitting coaxial cables separated from cables connected to home entertainment devices.
 Ensure that the DC power cord is not subject to undue stress or bending, which could damage the cable or cause it to
be accidentally unplugged from the rear panel DC IN jack.
 Be certain to install your transmitting antenna(s) so they cannot possibly come in contact with TV/FM radio or other
antennas, or with power or telephone lines.
Page 8
FT-991 Operating Manual
Installation and Interconnections
Connection of Microphone and Headphone


 DOWN
 UP
 +5V
 MIC GND
 MIC
 PTT
 GND
 FAST
FT-991 Operating Manual
Page 9
Installation and Interconnections
Key, Keyer, and Computer-Driven Keying Interconnections
The FT-991 includes many features for the CW operator. These functions will be detailed in the “Operation” section
later. Besides the built-in Electronic Keyer, two key jacks are provided, one on the front and one on the rear panel, for
convenient connection to keying devices.
The Menu selections allow you to configure the front panel KEY jack according to the device you wish to connect. For
example, you may connect your keyer paddle to the front panel KEY jack, and use Menu item “018 F KEYER TYPE” for
paddle input.
The KEY jack on the FT-991 utilize “Positive” keying voltage. Key-up voltage is approximately +3.3V DC, and keydown current is approximately 4 mA. When connecting a key or other device to the KEY jack, use only a 3-contact
(“stereo”) 1/4” phone plug; a 2-contact plug will place a short between the ring and (grounded) shaft of the plug, resulting in a constant “key-down” condition in some circumstances.
Page 10
FT-991 Operating Manual
Installation and Interconnections
VL-1000 Linear Amplifier Interconnections
Be sure that both the FT-991 and VL-1000 are turned off, and then follow the installation recommendations contained
in the illustration.
Note:
 Refer to the VL-1000 Operating Manual for details regarding amplifier operation.
 Do not attempt to connect or disconnect coaxial cables when your hands are wet.
Coaxial Cable (50Ω)
Connect to “INPUT 1” of the VL-1000
CONTROL
VP-1000
DC 48V IN
INPUT 1
GND
CT-58 ALC Cable (Option)
VP-1000
CT-58 Band Data Cable (Option)
ALC 1
ANT 3
ANT 2
Set the front panel’s
INPUT switch to the
“INPUT1”.
BAND-DATA 1
REM/ALC
INPUT
TUN/LIN
ANT
HF/50MHz
ANT
144/430MHz
GND
DC 13.8 V
ANT 1
HF/50MHz Antenna
144/430MHz Antenna
To link the FT-991 and VL1000 Power switches, set the
VL-1000 REMOTE switch to
the “ON” position.
FT-991 Operating Manual
Page 11
Installation and Interconnections
Interfacing to Other Linear Amplifiers
Coaxial Cable (50Ω)
Connect to “INPUT” of the linear amplifier
Linear Amplifier Connection Cable
(Option: T9207451)
Note
 The TX GND OUT pin (pin 2) of the TUN/LIN jack
is a transistor “open collector” circuit. It is capable of
handling positive relay coil voltages up to +60VDC
at 200 mA or +30 VDC at 1 A. If you plan to use
multiple linear amplifiers for different bands, you
must provide external band switching of the “Linear
Tx” relay control line from the “TX GND OUT” line
at the TUN/LIN jack.
 The specified range for ALC voltage to be used with
the FT-991 is 0 to -4 Volts DC.
 Amplifier systems utilizing different ALC voltages
will not work correctly with the FT-991, and their
ALC lines must not be connected if this is the case.
Page 12
GND
EXT ALC
GND
TX GND
GND
INPUT
ANT
ANT
HF/50MHz
INPUT
DC 13.8 V
HF/50MHz Antenna
TUN/LIN
GND
ANT
144/430MHz
144/430MHz Antenna
Important Note!
 Do not exceed the maximum voltage or current ratings for the “TX GND OUT” pin (pin 2) of the TUN/
LIN jack. This line is not compatible with negative
DC voltages, or AC voltages of any magnitude.
 Most amplifier control relay systems require only
low DC voltage/current switching capability (typically, +12V DC at 25 ~ 75 mA), and the switching
transistor in the FT-991 will easily accommodate
such amplifiers.
FT-991 Operating Manual
Front Panel Controls & Switches
ON/OFF Switch
Press and hold in this switch for one second to turn
the transceiver on. Similarly, press and hold in this
switch for one second to turn the transceiver off.
		KEY Jack
This 1/4-inch, 3-contact jack accepts a CW key or
keyer paddles (for the built-in electronic keyer), or
output from an external electronic keyer. Pinout is
shown on page ##. Key up voltage is +3.3 V DC,
and key down current is 4 mA. This jack may be
configured for keyer, “Bug”, “straight key”, or
computer keying interface operation via Menu item
“011 F CW KEYER” (see page ##).
Note:
You cannot use a 2-contact plug in this jack (to do so
produces a constant “key down” condition).
FT-991 Operating Manual
PHONES Jack
A 1/4-inch, 3-contact jack accepts either monaural or
stereo headphones with 2- or 3-contact plugs. When
a plug is inserted, the loudspeaker is disabled.
Note:
When wearing headphones, we recommend that you
turn the AF Gain levels down to their lowest settings
before turning power on, to minimize the impact on
your hearing caused by audio “pops” during switchon.
MIC Jack
This 8-pin jack accepts input from a microphone utilizing a traditional YAESU HF transceiver pinout.
Page 13
Front Panel Controls & Switches
F(M-LIST) Button
This button is used to display function list. The following functions can be accessed from the function
list:
NAR/WIDE, NB, AGC, ATT, IPO, NOTCH, CONT,
DNR, DNF, SHIFT, WIDTH, MOX, VOX, MONI,
MIC-EQ, PROC, BK-IN, SPEED, SQL
BAND Button
These keys allow one-touch selection of the desired
Amateur band (1.8 ~ 50 MHz).
The keys may also be used for direct entry of a desired operating frequency during VFO operation.
MODE Button
This button selects the operating mode. The selections available are:
M-LIST
Pressing and holding this button will show the memory channel list. ........
LSB, USB, AM, CW (LSB), CW (USB), FM,
MENU(SETUP) Button
MULTI Knob
MENU
This button is used to access the Menu system. The
various transceiver characteristics may be configured.
RTTY (LSB), RTTY (USB), C4FM, DATA (LSB),
DATA (USB), DATA (FM)
This knob allows you to select the Menu items and
settings.
SETUP
Pressing and holding this button will .......
Page 14
FT-991 Operating Manual
Front Panel Controls & Switches
12
13
A=B Button
Press this button momentarily to transfer the frequency or memory channel data, from VFO-A to
VFO-B, overwriting any previous contents in VFOB. Use this key to set both VFO-A and VFO-B to the
same frequency and mode.
A/B Button
Pressing this button momentarily, exchanges the
frequency or memory channel data, of VFO-A and
VFO-B.
RCL/STO Button
RCL (Recall)
Pressing this button, recalls one of up to five Quick
Memory Bank memories for operation.
STO (Store)
Pressing this button copies the contents (frequency,
mode, bandwidth, FM repeater offset, and CTCSS
settings) of VFO-A, into consecutive QMB Memories.
FT-991 Operating Manual
14
10
11
15
16
17
21
18
20
19
TUNE Button
This is the on/off switch for the FT-991’s Automatic
Antenna Tuner.
Pressing this button momentarily places the antenna
tuner in line between the transmitter final amplifier
and the antenna jack (The “TUNER” icon will appear in the display). Reception is not affected.
Pressing and holding in this button for two seconds,
while receiving in an amateur band, activates the
transmitter for a few seconds while the automatic
antenna tuner rematches the antenna system impedance for minimum SWR. The resulting setting is automatically stored in one of the antenna tuner’s 100
memories for instant automatic recall later when the
receiver is tuned near the same frequency.
Pressing this button momentarily, while the Tuner is
engaged, will take the Automatic Antenna tuner out
of the transmit line.
Note:
When the Automatic Antenna Tuner is tuning itself,
a signal is being transmitted. Therefore, be certain
that an antenna or dummy load is connected to the
selected antenna jack before pressing and holding in
the TUNE button to start antenna tuning.
Page 15
Front Panel Controls & Switches
C.S Button
V/M Button
TXW (TX Watch) Button
AM Button
Press this button momentarily to directly recall a favorite Menu Selection.
To program a Menu selection to the C.S button,
press the MENU(SETUP) button to enter the
Menu. Select the Menu item you want to set as
the short cut. Press the C.S button, then press the
MENU(SETUP) button; this will lock in the selected Menu item as the short cut.
Pressing and holding this button lets you monitor the
transmit frequency when split frequency operation is
engaged. Release the button to return to normal split
frequency operation.
FAST Button
Pressing this button will change the tuning of the
Main Tuning Dial knob (VFO-A) to a higher step
rate.
When this function is activated, the “FAST” indicator in the LED indicators area illuminates.
LOCK Button
This button toggles locking on/off for the Main Tuning Dial knob (VFO-A). With “Lock” on, the Main
Tuning Dial knob can still be turned, but the frequency will not change, and the “LOCK” indicator
in the LED indicators area illuminates.
This button toggles frequency control between VFOA and the memory system. In memory mode, “MEM”
(Memory Channel) will be shown in the display to
indicate the current selection. Pressing the V/M button displays the original memory frequency, and the
“MEM” will be displayed. Pressing it once more
returns frequency operation to VFO-A, and the icon
will no longer be displayed.
Pressing this button momentarily, displays the contents of the currently-selected memory channel for
10 seconds.
Pressing and holding in this key for one second (until
the double beep) copies the current operating data
into the currently selected memory channel, overwriting any previous data stored there.
SPLIT Button
Press this button to operate split frequency between
VFO-A (used for reception) and VFO-B (used for
transmission). If you press and hold in the SPLIT
button for one second, the “Quick Split” feature will
be engaged. VFO-B transmit will automatically be
set to a frequency 5 kHz higher than the VFO-A receive frequency, with the same operating mode. The
transceiver will operate in the Split mode.
CLAR Button
RX
Pressing this button activates the RX Clarifier. This
will allow you to temporarily adjust the receive
frequency up to ±9.999 kHz with the CLAR/VFOB knob. Press this button once more to return the
receiver to the original frequency; the Clarifier offset
will be remembered, in case you want to use it again.
To cancel the Clarifier offset, press the [CLEAR]
button.
Pressing this switch during Split operation will
change the tuning rate of the CLAR/VFO-B knob
(VFO-B) to 100 Hz/step.
When this function is activated, the “FAST” indicator in the LED indicators area illuminates.
TX
Pressing this button activates the TX Clarifier, to allow offsetting the transmit frequency temporarily.
Press this button once more to return the transmitter to the original frequency; the Clarifier offset
will be remembered, though, in case you want to
use it again. To cancel the Clarifier offset, press the
[CLEAR] button.
Page 16
FT-991 Operating Manual
Front Panel Controls & Switches
23
24
25
22
Main Tuning Dial Knob
This large knob adjusts the operating frequency of
VFO-A. Clockwise rotation of this knob increases
the frequency. Default tuning increments are 10 Hz
(CW, SSB), 50 Hz (RTTY/DATA), 100 Hz (AM/
FM). When the FAST button is pressed, the tuning
steps increases. The available steps are:
Operating Mode
LSB/USB/CW
AM/FM
RTTY/DATA
1 Step
10 Hz (100 Hz)
100 Hz (1 kHz)
5 Hz (100 Hz)
1 Dial Rotation
10 kHz (100 kHz)
100 kHz (1 MHz)
5 kHz (100 kHz)
Numbers in parentheses indicate steps when the FAST button is On.
CLAR/VFO-B Knob
During the VFO-A operation, this knob tunes the
Clarifier offset frequency up to ±9.999 kHz.
During Split operation, this knob adjusts the operating frequency of VFO-B.
RF GAIN Knob
The RF GAIN knob is the receiver RF gain control,
which adjusts the gain of the receiver RF and IF
amplifier stages. This control is normally left in the
fully clockwise position.
AF GAIN Knob
The AF GAIN knob sets the receiver audio volume
level. Typically, you will operate with this control set
between the 9 o’clock and 10 o’clock positions.
FT-991 Operating Manual
Page 17
Display Indications
LCD Display
Mode Indicator
Displays the current operating mode.
VFO-A Frequency Display
Shows the main band (VFO-A) frequency.
Tuning Offset Indicator
This indicates the relative offset of the CW-TUNE,
μ-TUNE, Clarifier, etc.
Configuration Indicator
TUNER
This indicator appears when the internal Automatic
Antenna Tuner is activated.
VOX
This indicator appears when the automatic voiceactuated transmitter switches in the SSB, AM, and
FM modes.
PROC
This indicator appears whenever the DSP Speech
Processor is activated.
MIC EQ
This indicator appears whenever the Three-Band
Parametric Microphone Equalizer is activated via
the Menu.
Page 18
NAR
This indicator appears whenever the receiver’s
narrow IF DSP filter is engaged.
REC
This indicator appears while the optional Voice
Memory Unit is recording your voice message, or
the Contest Keyer is recording your CW keying.
PLAY
This indicator appears while the optional Voice
Memory Unit is playing back the recorded voice
message, or the recorded Contest CW keying.
[+]/[-]
During FM repeater operation, a negative frequency shift will be indicated by “[-]” while a positive
frequency shift will be indicated by “[+]”.
DNR
This indicator appears whenever the Digital Noise
Reduction feature is activated.
DNF
This indicator appears whenever the Digital Notch
Filter is activated.
FT-991 Operating Manual
Display Indications
VFO-B Frequency Display
Shows the sub band (VFO-B) frequency during Split
operation.
S/PO Meter
On reception, this indicates the received signal
strength from S-0 to S-9+60dB.
On transmission, this indicates the RF Power Output,
from 0 to 150 Watts.
Advice:
 The S/PO meters can be set to the Peak-hold
function (BAR type only) via the menu item “008
BAR MTR PEAK HOLD”.
FT-991 Operating Manual
Scope Display
Function Keys
Clock
Indicates the current time.
Page 19
Display Indications
LED Indicators
RX Indicator
This indicator illuminates when the squelch opens.
TX Indicator
This indicator illuminates during transmission.
Memory Mode RX/TX Indicators
Green (Left):
This indicator illuminates when the receiver is active on the memory channel.
Red (Right):
This indicator illuminates when the transmitter is
active on the memory channel.
Main Band RX/TX Indicators
Green (Left):
This indicator illuminates when the receiver is active on the main band (VFO-A).
Red (Right):
This indicator illuminates when the transmitter is
active on the main band (VFO-A).
Page 20
Sub Band RX/TX Indicators
Green (Left):
This indicator illuminates when the receiver is active on the main band (VFO-B).
Red (Right):
This indicator illuminates when the transmitter is
active on the main band (VFO-B).
FAST/LOCK Indicators
FAST:
This indicator appears when the Main Tuning Dial
knob tuning rate is set to “fast”.
LOCK:
This indicator appears when the Main Tuning Dial
knob is locked.
FT-991 Operating Manual
Rear Panel
ANT Jack
Connect your main antenna(s) here, using type-M
(PL-259) connectors and coaxial feed lines. The internal antenna tuner affects only the antenna(s) connected here, and only during transmission.
Warning!
The 100V RF voltage (@100 W/50 Ω) is applied to
the TX RF section of the transceiver while transmitting. Do not touch the TX RF section while
transmitting.
TUN/LIN Jack
TUN (Tuner)
This 8-pin output jack is used for connection to the
FC-40 External Automatic Antenna Tuner.
LIN (Linear)
This 8-pin output jack provides band selection data,
which may be used for control of optional accessories such as the VL-1000 Solid-state Linear Amplifier.
RTTY/DATA Jack
DC IN Jack
This is the DC power supply connection for the
transceiver. Use the supplied DC cable to connect directly to a DC power supply, which must be capable
of supplying at least 23 A @13.8 VDC.
This 6-pin input/output jack accepts AFSK input
from a Terminal Node Controller (TNC) or an optional interface unit; it also provides fixed level (100mV @600 Ohms) receiver audio output, and FSK
keying line.
GND
REM/ALC Jack
Use this terminal to connect the transceiver to a good
earth ground, for safety and optimum performance.
Use a large diameter, short braided cable for making
ground connections, and please refer to page ## for
other notes about proper grounding.
To prevent damage from lightning, atmospheric electricity, electrical shock, etc., be
certain to provide a good earth ground.
FT-991 Operating Manual
REM (Remote)
By plugging the optional FH-2 Remote Control
Keypad into this gold-plated jack, direct access to
the FT-991 CPU is provided for control functions
such as contest memory keying, plus frequency and
function control.
ALC (
Page 21
Rear Panel
EXT SPKR Jack
This 3.5-mm, 2-contact, gold-plated jack provides
variable audio output for an external loudspeaker.
The audio output impedance at this jack is 4 - 8
Ohms, and the level varies according to the setting of
the front panel AF GAIN knob. Inserting a plug into
this jack disables the internal loudspeaker.
GPS/CAT Jack
This 9-pin serial DB-9 jack allows external computer
control of the FT-991. Connect a serial cable here
and to the RS-232C COM port on your personal
computer (no external interface is required).
Page 22
FT-991 Operating Manual
MH-31A8J Microphone Switches
PTT Switch
Press and hold the PTT (Push To Talk) switch to
start transmission.
DWN Button
Press the DWN (Down) button to scan the frequency
downward.
FST Button
Press the FST (Fast) button to increase the tuning
rate by a factor of ten when scanning the frequency.
UP Button
Press the UP button to scan the frequency upward.
Microphone
Speak into here during transmission.
FT-991 Operating Manual
Page 23
Optional FH-2 Switches
The optional Remote Control Keypad FH-2 can be used to control the optional DVS-6 Voice Memory capability for the
SSB/AM/FM modes; the contest memory keyer for the CW mode; and the text memory for the RTTY/DATA modes.
Some specific capabilities of the FH-2 are:
m On SSB/AM/FM modes, five channels of storage and playback of voice memory (20 seconds each), using your own
voice for recording (see page 71).
m On CW mode, the FH-2 provides storage and recall of CW messages for repetitive CQ and contest automatic number
transmissions (see page 85).
m On RTTY/DATA mode, the FH-2 provides storage and recall of TEXT messages for repetitive CQ transmissions (see
pages 104, 106).
[1], [2], [3], [4], [5] Buttons
[P/B] Button
These buttons work as the Voice Memory and CW
Message Memory Selection Key.
In the case of Voice Memory, up to 20 seconds of
audio may be stored on each channel.
For CW Messages and CW Text Messages, up to 50
characters ("PARIS" specification) may be stored
into each channel.
This button can be used to insert a space into the
position where the cursor is blinking.
[t], [u], [p], [q] Buttons
Press this button to store either a Voice Memory, or a
Contest Keyer Memory.
Usually, these buttons are used for tuning the VFO
frequency. Press the [p]/[q] buttons to change the
frequency in the same increments as the microphone
[UP]/[DWN] switches. Press the [t]/[u] buttons to
change the frequency by 100 kHz steps.
When programming the Contest Memory Keyer,
these buttons are used to move the cursor and select
the text characters.
Page 24
[LOCK] Button
This button may be used to lock out the FH-2 key
buttons, to prevent accidental activation of FH-2
operations.
[MEM] Button
[DEC] Button
When utilizing the sequential contest number
capability of the Contest Keyer, press this button to
decrement (decrease) the current Contest Number by
one digit (i.e. to back up from #198 to #197, etc.).
FT-991 Operating Manual
Basic Operation: Receiving on Amateur Bands
Before turning on the main power, please verify the following items once more.





Have you made all ground connections securely? See page ## for details.
Do you have your antenna(s) connected to the rear-panel Antenna jack(s)? See page ## for details.
Is your microphone (and/or key or paddle) connected? See pages ##, ## for details.
If using a linear amplifier, have all interconnections been successfully completed? See pages ##, ## for details.
Please rotate the AF GAIN control to the fully counter-clockwise position, to avoid a loud blast of audio when the
transceiver turns on. See page ## for details.
FT-991 Operating Manual
Page 25
Basic Operation: Receiving on Amateur Bands
Here is the typical start-up procedure for normal operation:
ON/OFF Switch
BAND Button
MODE Button
1. Turn on the external DC power supply.
2. Press and hold in the front-panel ON/OFF switch
until the transceiver turns on. After about five seconds, the transceiver is ready for full operation.
3. The transceiver will start up on 7.000.00 MHz LSB,
(or the previously used operating frequency) and
normal operation may begin.
Note:
To turn power off, press and hold in the front panel
ON/OFF switch for one second.
4. Rotate the AF GAIN knob to set a comfortable audio level of the incoming signals or noise. Clockwise
rotation of the AF GAIN knob increases the volume
level.
Note:
When using headphones, start by rotating the AF
GAIN knob counter-clockwise, then bring the volume level up after you put the headphones on. This
will minimize the chance of damage to your hearing
caused by an unexpectedly high audio level.
5. Press the BAND button to display the list of Amateur
bands on the LCD, then touch a key corresponding
to the band on which you wish to begin operation.
Advice:
 One-touch selection of each Amateur band between 1.8 and 50 MHz, 144 MHz, and 430 MHz
is provided.
 The FT-991 utilizes a triple band-stack VFO
selection technique, which permits storing up to
three favorite frequencies and modes onto each
VFO band register. For example, you may store
one frequency each on 14 MHz CW, RTTY, and
USB, then recall these frequencies by successive,
momentary touches of the [ 14 ] on the screen
displayed by pressing the BAND button. Each
Page 26
Main Tuning Dial Knob
AF GAIN Knob
Amateur band key may similarly have up to three
frequency/mode settings applied.
 When [ MHz ] is touched, the “MHz” notation
will appear in the display, and then rotation of the
CLAR/VFO-B knob will change the frequency
in 1 MHz steps.
6. Press the MODE button to display the available selections.
Touch the corresponding key to select the desired
operating mode.
Advice:
 By convention in the Amateur bands, LSB is
used on the 7 MHz and lower bands (with the
exception of 60 meters), while USB is utilized on
the 14 MHz and higher bands.
 When changing modes from SSB to CW, you
will observe a frequency shift on the display.
This shift represents the BFO offset between the
“zero beat” frequency and the audible CW pitch
(tone) you can hear (the pitch is programmed via
the Menu item “060 CW FREQ DISPLAY”), even
though the actual tone that you hear is not changing.
When
operating on the FM mode, repeatedly

touch SQL] (Squelch) on the screen displayed
by pressing the F(M-LIST) button to point where
the background noise is just silenced. This is the
point of maximum sensitivity to weak signals.
Excessive advancement of [SQL] will decrease
the ability of the receiver to detect weak signals.
FT-991 Operating Manual
Basic Operation: Receiving on Amateur Bands
7. Rotate the Main Tuning Dial knob to tune around the
band, and begin normal operation.
Advice:
 Clockwise rotation of the Main Tuning Dial knob
increases the operating frequency, one “step”
of the synthesizer at a time; similarly, counterclockwise rotation of the Main Tuning Dial knob
will decrease the frequency. Two settings, one
“normal” and one “fast”, are available for each
operating mode. Pressing the FAST button engages the “Fast” tuning selection (see chart below).
Main Tuning Dial Knob Tuning Rate
Operating
Mode
LSB/USB/CW/
RTTY/DATA
AM/FM
1 Step
1 Dial Rotation
1 / 5 / 10 Hz
(100 Hz)
100 Hz (1 kHz)
1 / 5 / 10 kHz
(100 kHz)
100 kHz (1 MHz)
Numbers in parentheses indicate steps when the FAST button is On.
 If you want to effect rapid frequency change,
there are several techniques available:
 Direct keyboard entry of the frequency.
 Use the microphone’s UP/DWN scanning
keys, if your microphone is so equipped.
FT-991 Operating Manual
Page 27
Basic Operation: Receiving on Amateur Bands
Operation on 60-Meter (5 MHz) Band (U.S. version only)
The recently-released 60-meter band is covered, in the FT-991, by fixed memory channels. These channels are set to
USB or CW, and they appear between the “last” PMS channel (“P9U”) and the first “regular” memory channel (Channel
1):
1. Press the V/M button once to enter the “Memory”
mode; the “MEM” icon will appear in the display.
2. Touch [MCH] on the screen displayed by pressing
the F(M-LIST) button. The “MCH” notation and a
memory channel number will appear on the display
to signify that rotation of the MULTI knob will allow
selection of the memory channel.
3. Memory channels (“501” through “510”) are preprogrammed, at the factory, with the permitted frequencies in the 5 MHz band, and the USB or CW
mode is automatically selected on these channels.
4. To exit from 60-meter operation and return to the
VFO mode, just press the V/M button.
Note:
The frequencies and operating mode for 5 MHz band
operation are fixed, and may not be changed.
Page 28
F(M-LIST) Button
V/M Button
Main Tuning Dial Knob
MULTI Knob
Channel
Number
501
502
503
504
505
506
507
508
509
510
Frequency
5.332000 MHz
5.348000 MHz
5.358500 MHz
5.373000 MHz
5.405000 MHz
5.332000 MHz
5.348000 MHz
5.358500 MHz
5.373000 MHz
5.405000 MHz
FT-991 Operating Manual
Basic Operation: Receiving on Amateur Bands
CLAR (Clarifier) Operation
The CLAR button and CLAR/VFO-B knob are used to offset the receive frequency, the transmit frequency, or both,
from their settings on the VFO-A frequency. Four small numbers on the TFT Display show the current Clarifier offset.
The Clarifier controls on the FT-991 are designed to allow you to preset an offset (up to ±9.99 kHz) without actually retuning, and then to activate it via the Clarifier CLAR button. This feature is ideal for following a drifting station, or for
setting the small frequency offsets sometimes utilized in DX “Split” work.
Here is the technique for utilizing the Clarifier:
1. Press the CLAR button. The “RX” notation will appear in the TFT Display, and the programmed offset
will be applied to the receive frequency.
2. Rotation of the CLAR/VFO-B knob will allow you
to modify your initial offset on the fly. Offsets of up
to ±9.99 kHz may be set using the Clarifier.
CLAR/VFO-B Knob
CLAR Button
To cancel Clarifier operation, press the CLAR button.
The “RX” notation will disappear from the display.
Advice:
 Turning the Clarifier off merely cancels the application of the programmed offset from the receive and/
or the transmit frequencies. To clear the Clarifier offset, and reset it to “zero,” press and hold the CLAR
button. The programmed offset is displayed in the
small multi-channel window of the frequency display.
 The Clarifier operation (including the offset frequency) will be memorized independently on each VFO
stack of VFO-A and VFO-B.
FT-991 Operating Manual
Page 29
basiC operaTion: reCeiving on aMaTeur bands
LOCK
You may lock the setting of the Main Tuning Dial knob (for VFO-A frequency tuning) and the CLAR/VFO-B knob (for
VFO-B frequency tuning during Split operation), to prevent accidental frequency change.
Main Tuning Dial Knob Lock
To lock the Main Tuning Dial knob, press the LOCK
button that is located to the right of the Main Tuning
Dial knob. To unlock the Dial setting, and restore normal tuning, press the LOCK button once more.
LOCK Button
Advice:
The lock feature will be memorized independently on
the Main Tuning Dial knob and the CLAR/VFO-B
knob.
DIMMER
The illumination level of the TFT display and LED indicators (above the Main Tuning Dial knob), may be adjusted via
Menu items 009 and 010.
To adjust the illumination level:
MENU Button
1. Press the MENU button to enter the Menu mode.
2. Rotate the MULTI knob to select Menu item “006
DIMMER LED” (for LED indicators) or “007 DIMMER TFT” (for TFT display).
3. Touch [ SELECT ] on the LCD then rotate the
MULTI knob to select the desired illumination level.
4. Touch [ENTER] on the LCD, then touch [BACK]
on the LCD or press the MENU button to save the
new setting and exit to normal operation.
MULTI Knob
VFO COLOR
The background color of the VFO-A frequency in the TFT display may be selected via Menu item 007.
1. Press the MENU button to enter the Menu mode.
2. Rotate the MULTI knob to select Menu item “005
DISPLAY COLOR”.
3. Touch [ SELECT ] on the LCD, then rotate the
MULTI knob to select from the following colors:
BLUE (default) / SKY BLUE / GREEN / PURPLE /
RED / ORANGE / GRAY
4. Touch [ENTER] on the LCD, then touch [BACK]
on the LCD or press the MENU button to save the
new setting and exit to normal operation.
Background color
MENU Button
MULTI Knob
Page 30
fT-991 operaTing Manual
Convenience Features
Band Stack Operation
The FT-991 utilizes a triple band-stack VFO selection technique, that permits you to store up to three favorite frequencies and modes onto each band’s VFO register. For example, you may store one frequency each on 14 MHz CW, RTTY,
and USB, then recall these VFOs by successive, momentary touches of [14] on the screen displayed by the BAND button. Each Amateur band key may similarly have up to three frequency/mode settings applied. Note that only the VFO-A
system has the band stacks.
A typical setup, for the 14 MHz band, might be arranged like this:
1. Program 14.025 MHz, CW Mode, press the BAND
button, then touch [14] on the LCD;
2. Program 14.080 MHz, RTTY Mode, press the
BAND button, then touch [14] on the LCD;
3. Program 14.195 MHz, SSB Mode, press the BAND
button, then touch [14] on the LCD.
BAND Button
With this configuration, successive momentary touches
of [14] on the screen displayed by the BAND button
will allow you to step sequentially through these three
VFOs.
C.S (Custom Switch)
The front panel C.S button may be programmed to directly access an often-used Menu Mode selection.
C.S Setup
1. Press the MENU button to engage the Menu mode;
the Menu list will appear on the display.
2. Rotate the MULTI knob to select the Menu item you
want to access with the front panel C.S button.
3. Press the C.S button to lock in your selection.
4. Press the MENU button or touch [BACK] on the
LCD to save the new configuration and exit to normal operation.
MENU button
C.S button
MULTI Knob
Menu Selection Recall via C.S button
Press the C.S button.
The programmed Menu item will appear on the display.
Press the MENU button or touch [BACK] on the LCD
exit to normal operation.
FT-991 Operating Manual
Page 31
ConvenienCe feaTures
Scope
This function displays a convenient spectrum scope for monitoring the band conditions. Both strong and weak signals
can be displayed in an easy-to-understand manner on the TFT screen. This multifunctional scope takes into consideration the operator’s preference, by switching between the convenient CENTER mode where the VFO frequency is
constantly in the center of the screen (for monitoring conditions on both sides of your operating frequency), and the FIX
mode, where the frequency is fixed to the left side of the screen (for convenience in monitoring in the band).
Note: Since the FT-991 has only one receiver the audio will be muted while the spectrum scope is scanning.
SCOPE
Spectrum scope display

1. Press the [SCOPE] button momentarily to display
the scope screen.
Five different screens are shown on the TFT display
by pressing the [SCOPE] button.
Advice:
 During continuous sweeping, no audio will be heard.
Full screen spectrum scope display
Page 32
fT-991 operaTing Manual
Convenience Features
More Frequency Navigation Techniques
Keyboard Frequency Entry
The Operating frequency may be entered directly into
the current VFO, using the keyboard screen displayed
by pressing the front panel BAND button.
Example: Enter 14.250.00 MHz
1. Press the BAND button to begin the direct frequency
entry process.
2. Touch [ENT] on the LCD. The first digit of the frequency (the leftmost digit) will blink.
3. Enter, in order, the digits of the operating frequency,
touching the keys on the LCD
The decimal point after the “MHz” portion of the
frequency must be entered, but no decimal point is
required after the “kHz” portion.
3. Touch [ENT] on the LCD once more to complete
the operating frequency entry. A short “beep” will
confirm that the entry was successful, and the new
operating frequency will appear on the display.
Advice:
If you attempt to enter a frequency outside the operating range of 30 kHz ~ 56 MHz, the microprocessor
will ignore the attempt, and you will be returned to
the previous operating frequency. If this happens,
please try again, taking care not to repeat the error in
the frequency entry process.
FT-991 Operating Manual
Using the UP/DWN buttons of the
supplied MH-31A8J Hand Microphone
The UP/DWN buttons on the supplied MH-31A8J Hand
Microphone may also be used to manually scan the frequency upward or downward.
T h e m i c r o p h o n e ’s U P /
DWN buttons utilize the
tuning steps of the Main
Tuning Dial knob.
When the microphone FST
button is pressed, the tuning
rate increases by a factor of
ten, in a manner similar to
the transceiver front panel
FAST button.
Page 33
Convenience Features
Receiver Operation (Front End Block Diagram)
The FT-991 includes a wide range of special features to suppress the many types of interference that may be encountered on the HF bands. However, real world interference conditions are constantly changing, so optimum setting of the
controls is somewhat of an art, requiring familiarity with the types of interference and the subtle effects of some of the
controls. Therefore, the following information is provided as a general guideline for typical situations, and a starting
point for your own experimentation.
The FT-991 interference-fighting circuitry begins in its “RF” stages, and continues throughout the entire receiver section. FT-991 allows configuration of the features described below.
CONTOUR Filter
The DSP Contour filter has the unique ability to provide either a null or a peak in tunable segments of the
receiver passband. You may suppress interference and
excessive frequency components on an incoming signal,
or you may peak those tunable frequency segments. The
level of the null or peak, and the bandwidth, over which
it is applied, are adjustable via the Menu.
IF SHIFT
The passband center frequency of the IF DSP filter may
be moved up or down by adjusting this control.
IF WIDTH
The width of the IF DSP filtering may be adjusted using
this control.
IF NOTCH
The IF Notch filter is a high-Q notch filter that can eliminate, or significantly reduce an interfering carrier.
DNF (Digital Notch filter)
When multiple interfering carriers are encountered during reception, the Digital Notch Filter can significantly
reduce the level of these signals.
DNR (Digital Noise Reduction)
The DSP’s Digital Noise Reduction (DNR) feature utilizes 15 different mathematical algorithms to analyze
and suppress different noise profiles encountered on the
HF/50 MHz bands. Choose the selection that provides
the best noise suppression, and allows the signal to rise
up out of the noise.
AGC
The AGC system is highly adaptable to changing signal
and fading characteristics, making reception possible
under the most difficult conditions.
Front End Block Diagram
Page 34
FT-991 Operating Manual
Interference Rejection
ATT (Attenuator)
When extremely strong local signals or high noise degrades reception, you can use [ATT] displayed by pressing the
F(M-LIST) button to insert 6, 12, or 18-dB of RF attenuation in front of the RF amplifier.
F(M-LIST) Button
1. Press the F(M-LIST) button, then touch [ATT] on
the LCD several times to set the desired attenuation
level, per the chart below.
OFF: Attenuator is Off
-6dB: The incoming signal power is reduced by 6
dB (Signal voltage reduced by 1/2)
-12dB: The incoming signal power is reduced by 12
dB (Signal voltage reduced to 1/4)
-18dB: The incoming signal power is reduced by 18
dB (Signal voltage reduced to 1/8)
The selected attenuation level will be indicated in
the ATT column of the Key Function Display on the
TFT display.
2. To restore full signal strength through the Attenuator
circuit area, touch [ATT] on the LCD to restore the
ATT display to the “OFF” position.
Advice:
 If background noise causes a high S-meter indication on clear frequencies, touch [ATT] on the LCD until the Smeter drops to about “S-1”. This setting optimizes the trade-off between sensitivity, noise, and interference immunity. Also, once you have tuned in a station you want to work, you may want to reduce sensitivity further (add more
attenuation) by touching [ATT] on the LCD to a higher setting. This reduces the strength of all signals (and noise)
and can make reception more comfortable, important especially during long QSOs. When looking for weak signals
on a quiet band, you will want maximum sensitivity, so the IPO should be disabled and [ATT] on the LCD should be
set to “OFF.” This situation is typical during quiet times on frequencies above 21 MHz, and when using a small or
negative-gain receiving antenna on other bands.
FT-991 Operating Manual
Page 35
Interference Rejection
IPO (Intercept Point Optimization)
The IPO feature allows the operator to optimize the characteristics of the receiver front end, depending on the current
noise level and the strength of incoming signals.
Touch [IPO] displayed by pressing the F(M-LIST) button repeatedly, to set the desired characteristic of the
receiver front end, according to the chart below.
F(M-LIST) Button
AMP1: Amplifies the incoming signals, using a low
distortion RF preamplifier (gain: approx. 10
dB).
AMP2: Amplifies the incoming signals, using a
2-stage low-distortion RF preamplifier (total
gain: approx. 20 dB).
IPO: Bypasses the RF preamplifier, yielding direct
feed to the first mixer.
The selected receiver RF preamplifier will be indicated
in the IPO column of the Key Function Display on the
TFT display.
Advice:
 On the 10 MHz and lower bands, it generally is not
necessary to use any preamplifier at all; selecting the
“IPO” position as described above will increase the
strong-signal-handling capability of the receiver, and
generally will result in more pleasant reception due
to reduced noise. If you can hear band noise with the
preamplifiers disengaged, then a preamplifier is generally not needed.
Page 36
FT-991 Operating Manual
Interference Rejection
IF Noise Blanker (NB) Operation
The FT-991 includes an effective IF Noise Blanker, which can significantly reduce noise caused by automotive ignition
systems.
1. Touch [NB] displayed by pressing the F(M-LIST)
button briefly to reduce short duration pulse noise
such as from switching transients, automobile ignitions and power lines. The “NB ON” will appear in
the display to confirm that the Narrow-NB is operating.
2. Touch [NB ] on the LCD again to reduce longerduration man-made pulse noise. The “NBW ON”
will appear in the display to confirm that the WideNB is operating.
3. If desired, you may adjust the Noise Blanker level
via Menu item “024 NB LEVEL” to the point where
the offending noise is best reduced or eliminated.
See box below for details.
4. To end Noise Blanker operation, touch [NB] on the
LCD once more. The “NB OFF” will appear in the
display, confirming that the Noise Blanker is no longer in operation.
F(M-LIST) Button
Adjusting the Noise Blanker Level
1. Press the MENU button to engage the Menu
mode.
2. Rotate the MULTI knob to select Menu item “024
NB LEVEL”.
3. Touch [SELECT] on the LCD
4. Rotate the MULTI knob to the point where the
offending noise is best reduced or eliminated.
5. Touch [ ENTER ] on the LCD, then press the
MENU button or touch [BACK] on the LCD to
lock in the new setting and exit to normal operation.
FT-991 Operating Manual
MENU button
MULTI Knob
Page 37
Interference Rejection
CONTOUR Control Operation
The Contour filter system provides a gentle perturbation of the IF filter passband. The Contour is set to either suppress,
or boost specific frequency components, and thus enhances the sound and readability of a received signal.
1. Touch [ CONT ] displayed by pressing the F(MLIST) button to activate the Contour filter. The DSP
graphic display will illuminate and the current “null”
(or “peak”) position of the Contour filter will appear
in the CONTOUR indicator on the display.
2. Rotate the MULTI knob to achieve the most naturalsounding audio reproduction on the incoming signal.
Advice:
The display will show the Contour frequency whenever [CONT] on the LCD is touched.
3. To cancel Contour tuning, touch [ CONT ] on the
LCD.
Advice:
Alternate touches of [ CONT ] on the LCD will
switch the Contour filter between on and off.
Advice:
 The Contour filter level (either a null or a peak) may
be adjusted using Menu item “112 CONTOUR LEVEL”. The factory default setting is for a null of –15
(dB).
 The bandwidth over which the Contour filter effect
is applied may be adjusted using Menu item “113
CONTOUR WIDTH”. The factory default setting is
10. When the set value is increased, the bandwidth
becomes wider.
F(M-LIST) Button
Refer to Figure “B”, this illustrates an “indentation” of the Contour filter in the center of
the passband. The Contour filter places a lowQ “notch” in the passband, per the settings of
Menu items “112 CONTOUR LEVEL” and “113
CONTOUR WIDTH” (referenced above). Counterclockwise rotation (to the left) of the MULTI
knob causes the notch to move toward a lower
frequency within the passband, while clockwise
rotation (to the right) causes the notch to move
toward a higher frequency within the passband.
By removing interference or unwanted frequency
components of the incoming signal, it is possible
to make the desired signal rise out of the background noise/interference, enhancing intelligibility.
IF BANDWIDTH
IF BANDWIDTH
IF BANDWIDTH
MULTI
MULTI
MULTI
Quick Point:
By judicious use of the Contour filter, the “shoulder” of the passband response may be altered, or components may be
removed from within the passband, allowing the desired signal to rise above the background noise and interference in a
manner not obtainable with other filtering systems.
Page 38
FT-991 Operating Manual
Interference Rejection
IF SHIFT Operation (SSB/CW/RTTY/PKT Modes)
IF SHIFT allows you to move the DSP filter passband higher or lower, without changing the pitch of the incoming signal, and thus reduces or eliminates interference. Because the carrier tuning frequency is not varied, there is no need to
re-tune the operating frequency to eliminate the interference. The total passband tuning range for the IF SHIFT system
is ±1 kHz.
1. Touch [ SHIFT ] displayed by pressing the F(MLIST) button repeatedly to reduce the interference.
Advice:
The display will show the shift value of the IF
SHIFT whenever [SHIFT] on the LCD is touched.
F(M-LIST) Button
Referring to Figure “A”, note the depiction of the
IF DSP filter as the thick line, with MULTI knob
in the 12 o’clock position. In Figure “B”, an interfering signal has appeared inside the original
passband. In Figure “C”, you can see the effect
of rotating the MULTI knob. The interference
level is reduced by moving the filter passband so
that the interference is outside of the passband.
Desired Signal
Desired Signal
QRM
Desired Signal
QRM
IF BANDWIDTH
IF BANDWIDTH
IF BANDWIDTH
MULTI
MULTI
MULTI
FT-991 Operating Manual
Page 39
Interference Rejection
WIDTH (IF DSP Bandwidth) Tuning (SSB/CW/RTTY/DATA Modes)
The IF WIDTH tuning system allows you to vary the width of the DSP IF passband, to reduce or eliminate interference.
Moreover, the bandwidth may actually be expanded from its default setting, should you wish to enhance incoming signal fidelity when interference on the band is low.
1. Touch [ WIDTH ] displayed by pressing the F(MLIST) button repeatedly to reduce the interference.
Advice:
The frequency display will show the bandwidth of
the IF passband whenever [WIDTH] is touched.
Referring to Figure “B”, you can see the default
bandwidth on the SSB mode.
By rotating the MULTI knob to the left, the bandwidth will narrow (see Figure “A”, while rotation
of the MULTI knob to the right, as depicted in
Figure “C”, will increase the bandwidth.
IF BANDWIDTH
IF BANDWIDTH
IF BANDWIDTH
F(M-LIST) Button
Using IF SHIFT and WIDTH Together
The IF SHIFT and Variable IF WIDTH features
together form a very effective interference-fighting filtering system.
For example, in Figure “A”, you can see how interference has appeared both on the high and low
sides of the desired signal. Touch [WIDTH] on
the LCD, the interference from one side can be
eliminated (Figure “B”). Next, rotate the MULTI
knob to re-position the passband (Figure “C”),
the interference on the opposite side can be removed, without re-introducing the interference
previously eliminated in Figure “B”.
MULTI
MULTI
Page 40
Desired Signal
MULTI
The default bandwidths, and total bandwidth adjustment range, will vary according to the operating mode:
SSB Mode: 1.8 kHz ~ 4.0 kHz (default: 2.4 kHz).
CW Mode: 500 Hz ~ 2.4 kHz (default: 2.4 kHz)
RTTY/DATA Modes: 500 Hz ~ 2.4 kHz (default:
500 Hz)
QRM
Desired Signal
QRM
QRM
IF BANDWIDTH
Desired Signal
QRM
QRM
IF BANDWIDTH
QRM
IF BANDWIDTH
Advice:
For best interference reduction, the WIDTH and
SHIFT features are the primary tools you should
use, after narrowing the bandwidth (WIDTH)
and/or adjusting the center of the passband
(SHIFT). The Contour control may then yield
additional signal-enhancement benefits on
the net residual bandwidth. Even more, the IF
NOTCH Filter (described later) may also be
used, in conjunction with these filter systems, to
significant advantage.
FT-991 Operating Manual
Interference Rejection
NARROW (NAR) One-Touch IF Filter Selection
Touching [NAR/WIDE] displayed by pressing the F(M-LIST) button provides one-touch, mode-specific, selection of a
narrow IF DSP filter setting that does not require resetting the bandwidth control to the WIDTH/SHIFT system.
Touching [NAR/WIDE] on the LCD once more returns
the bandwidth control to the WIDTH/SHIFT system.
The factory default bandwidths are:
Operating Mode
SSB
CW
RTTY/DATA
AM
F M ( 28/50/144/430
MHz Bands)
[NAR/WIDE] Touch Key
“ON”
“OFF”
200 Hz ~ 1.8 kHz
1.8 ~ 3.0 kHz
(1.5 kHz)
(2.4 kHz)
50 ~ 500 Hz
500 Hz ~ 3.0 kHz
(500 Hz)
(2.4 kHz)
50 ~ 500 Hz
500 Hz ~ 2.4 kHz
(300 Hz)
(500 Hz)
6 kHz
9 kHz
9 kHz
16 kHz
F(M-LIST) Button
: Depends on the [WIDTH] setting
( ): Default Bandwidth
Advice:
 When the narrow bandwidth is selected, the “NAR”
icon will appear in the display.
 If [NAR/WIDE] on the LCD has been touched to
engage the narrow filter, you may still adjust the narrow IF bandwidth with [WIDTH] on the LCD and
the MULTI knob. The IF SHIFT is also operational.
 When you touch [NAR/WIDE] on the LCD in the
FM mode, both transmit and receive bandwidths are
narrowed.
FT-991 Operating Manual
Page 41

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Author                          : YAESU MUSEN CO., LTD.
Create Date                     : 2014:10:23 16:34:37+09:00
Modify Date                     : 2014:10:23 16:34:37+09:00
Trapped                         : False
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2014:10:23 16:34:37+09:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Title                           : 05_1_User_Manual.pdf
Creator                         : YAESU MUSEN CO., LTD.
Document ID                     : uuid:420f1254-0c5e-4ea9-b88c-c738e9b1f1a3
Instance ID                     : uuid:34a5bdd4-cbe4-4a6c-9c60-fef4c2e5c7f4
Producer                        : Adobe PDF Library 10.0.1
Page Count                      : 43

EXIF Metadata provided by EXIF.tools