Yaesu Musen 20575X50 HF / VHF / UHF All Mode Transceiver User Manual FT 991

Download:
Mirror Download [FCC.gov]
Document ID	2440475
Application ID	XT0U74oL01ckNxQiV1w87A==
Document Description	Users Manual Part 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	398.76kB (4984445 bits)
Date Submitted	2014-11-11 00:00:00
Date Available	2014-11-11 00:00:00
Creation Date	2014-10-10 15:19:31
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2014-10-10 15:19:44
Document Title	FT-991_User Manual.pdf
Document Creator	Adobe InDesign CS6 (Windows)
Document Author:	YAESU MUSEN CO., LTD.

Interference Rejection
IF NOTCH Filter Operation (SSB/CW/RTTY/DATA/AM Modes)
The IF NOTCH filter is a highly effective system that allows you to slice out an interfering beat note or other carrier
signal from inside the receiver passband.
1. Press the F(M-LIST) button, then touch [NOTCH]
on the LCD to activate the Notch filter. The DSP
graphic display will illuminate and the current “null”
position of the NOTCH filter will appear in the
NOTCH indicator on the display. The MULTI knob
functions as the Notch adjustment knob.
2. Rotate the MULTI knob to adjust the “null” position
of the Notch filter.
3. To cancel the NOTCH filter, touch [NOTCH] on
the LCD. The graphic disappears from the NOTCH
indicator on the display, confirming that the NOTCH
filter is no longer in operation.
Advice:
Alternate touches of [ NOTCH ] , will switch the
NOTCH filter between on and off.
Advice:
 The bandwidth of the NOTCH filter (either narrow
or wide) may be adjusted using Menu item “114
IF NOTCH WIDTH”. The factory default setting is
“WIDE”.
F(M-LIST) Button
The performance of the IF NOTCH filter is illustrated in Figure “A”, where the effect of rotation
of the MULTI knob is depicted. In Figure “B”
you can see the notching effect of the IF NOTCH
filter as you rotate the MULTI knob to eliminate
the interfering heterodyne.
Desired Signal
QRM
(Heterodyne)
Desired Signal
QRM
(Heterodyne)
IF BANDWIDTH
IF BANDWIDTH
MULTI
Page 42
FT-991 Operating Manual
Interference Rejection
Digital NOTCH Filter (DNF) Operation
The Digital NOTCH Filter (DNF) is an effective beat-canceling filter that can null out a number of interfering beat notes
inside the receiver passband. Because this is an Auto-Notch feature, there is no adjustment knob associated with this filter.
Advice:
If a very strong interfering carrier is encountered, we recommend you first use the IF NOTCH filter, as it is the most effective notching tool in the receiver section.
1. Press the F(M-LIST) button, then touch [DNF] on
the LCD. The “DNF” will appear in the display.
F(M-LIST) Button
To disable the Digital NOTCH Filter, just repeat the
above procedure, touching [DNF] on the LCD to choose
“OFF”. The “DNF” will turn off, confirming that the
Digital NOTCH Filter is not active.
Digital Noise Reduction (DNR) Operation
The Digital Noise Reduction (DNR) system is designed to reduce the level of random noise found on the HF and 50
MHz bands, and it is especially effective during SSB operation. By setting the Menu item “110 DNR LEVEL”, any of 15
different noise-reduction algorithms can be selected; each of these algorithms was created for dealing with a different
noise profile. You will want to experiment with the DNR system to find the best setting corresponding to the noise currently being experienced.
1. Press the F(M-LIST) button, then touch [DNR] on
the LCD. The “DNR” will appear in the display.
F(M-LIST) Button
To disable the DNR system, just repeat the above procedure, touching [DNR] on the LCD to choose “OFF”. The
“DNR” will turn off, confirming that the DNR system is
not active.
FT-991 Operating Manual
Page 43
Tools for Comfortable and Effective Reception
RF Gain
The RF Gain control provides manual adjustment of the gain levels for the receiver RF and IF stages, to account for
noise and signal strength conditions at the moment.
1. The RF GAIN knob should, initially, be rotated to
the fully clockwise position. This is the point of
maximum sensitivity.
2. Counter-clockwise rotation of the RF GAIN knob
will gradually reduce the system gain.
Advice:
 As the RF GAIN knob is rotated counterclockwise
to reduce the gain, the S-meter reading will rise. This
indicates that the AGC voltage being applied to the
receiver is increasing (this causes a reduction in receiver gain).
 Rotating the RF GAIN knob control to the fully
counter-clockwise position will essentially disable
the receiver, as the gain will be greatly reduced. In
this case, the S-meter will appear to be “pegged”
against the right edge of the analog S-meter scale.
RF GAIN Knob
Quick Point:
 Reception frequently can be optimized by rotating
the RF GAIN knob slightly counter-clockwise to the
point where the “stationary” meter indication is set
just about the same as the incoming noise level. This
will reduce the RF gain to find a level of improved
signal to noise ratio.
 The RF Gain control, along with the IPO and the Attenuator features, all affect the system receiver gain
in different ways. The IPO generally should be the
first feature engaged when dealing with a high noise
level, or a crowded, high-level signal environment.
Also, the IPO generally should be the first feature
engaged, if the frequency is low enough to allow the
preamplifier to be bypassed. Thereafter, the RF Gain
and Attenuator features may be employed to provide
precise, delicate adjustment of the receiver gain to
fully optimize performance.
Page 44
FT-991 Operating Manual
Tools for Comfortable and Effective Reception
Audio Peak Filter
1. Press the F(M-LIST) button, then touch [APF] on
the LCD. The “APF” indicator will appear in the
DSP display.
Advice:
When APF is engaged, the peak position of the APF
is depicted graphically in the NOTCH indicator on
the display.
2. Touch [AFP] on the LCD again to disable the APF.
F(M-LIST) Button
Advice:
The APF may only be activated while the transceiver is
in CW mode.
FT-991 Operating Manual
Page 45
Tools for Comfortable and Effective Reception
AGC (Automatic Gain Control)
The AGC system is designed to help compensate for fading and other propagation effects. The AGC characteristics can
be individually set for each operating mode. The basic objective of AGC is to maintain a constant audio output level
once a certain minimum threshold of signal strength is achieved.
Press the F(M-LIST) button, then touch [AGC] on the
LCD repeatedly to select the desired receiver-recovery
time constant. You will observe the AGC status notation
in the AGC column of the Key Function Display on the
TFT display, denoting the AGC receiver-recovery time
currently in use. For most operations, we recommend
the “AUTO” mode. Additionally, you may disable the
AGC by touching [AGC] on the LCD.
Note:
 The “AUTO” selection mode selects the optimum
receiver-recovery time for the reception mode.
In this case, the selected receiver-recovery time in
the AGC column of the Key Function Display glows
green (Normally glows blue).
 Touching [AGC] on the LCD allows selection of the
desired receiver-recovery time constant. Normally,
the “AUTO” selection is satisfactory for most situations, but in the event of operation on a crowded
band where you wish to receive a weak signal, you
may wish to change the setting to FAST. The AUTO
mode selections are:
Operating Mode
LSB/USB/AM
CW/FM
RTTY/DATA
Page 46
AUTO AGC Selection
SLOW
FAST
MID
F(M-LIST) Button
Advice:
 If the AGC receiver-recovery time is set to “Off” by
touching [AGC] on the LCD, the S-meter will no
longer deflect. Additionally, you will likely encounter distortion on stronger signals, as the IF amplifiers
and the following stages are probably being overloaded.
Quick point:
Several aspects of AGC performance may be configured
via the Menu. However, because AGC can have such a
profound impact on overall receiver performance, we
generally do not recommend any changes to the AGC
Menu selections until you are thoroughly familiar with
the performance of the FT-991.
Terminology:
Automatic Gain Control, or AGC, is a circuit that senses
the received signal strength, and then limits the gain of
the RF and IF stages to keep the output audio volume at
a more-or-less constant level. AGC also protects the RF,
IF, Audio, and DSP stages from overload, as it limits the
signal strength that is allowed to flow, irrespective of the
input signal level.
FT-991 Operating Manual
Tools for Comfortable and Effective Reception
Adjustable Receiver Audio Filter
The FT-991 includes an adjustable receiver audio filter, that provides precise, independent control of the low; and upper
audio ranges.
1. Press the MENU button to enter the Menu mode.
2. Rotate the MULTI knob to find Menu items “040”
through “043” these parameters apply to the adjustment of the receiver audio filter in the AM mode,
Menu items “050” through “053” apply to the
adjustment of the RX audio filter in the CW mode,
Menu items “067” through “070” apply to the adjustment of the RX audio filter in the DATA mode,
Menu items “092” through “095” apply to the adjustment of the RX audio filter in the RTTY mode,
and Menu items “102” through “105” apply to the
adjustment of the RX audio filter in the SSB mode
3. Touch [SELECT] on the LCD.
4. Rotate the MULTI knob to adjust the receiver audio
response as desired.
5. Touch [ENTER] on the LCD to save the new setting.
6. Press the MENU button or touch [BACK] on the
LCD to exit to normal operation.
Mode
AM
CW
DATA
RTTY
SSB
FT-991 Operating Manual
Menu Item
040 AM LCUT FREQ
041 AM LCUT SLOPE
042 AM HCUT FREQ
043 AM HCUT SLOPE
050 CW LCUT FREQ
051 CW LCUT SLOPE
052 CW HCUT FREQ
053 CW HCUT SLOPE
067 DATA LCUT FREQ
068 DATA LCUT SLOPE
069 DATA HCUT FREQ
070 DATA HCUT SLOPE
092 RTTY LCUT FREQ
093 RTTY LCUT SLOPE
094 RTTY HCUT FREQ
095 RTTY HCUT SLOPE
102 SSB LCUT FREQ
103 SSB LCUT SLOPE
104 SSB HCUT FREQ
105 SSB HCUT SLOPE
MENU Button
MULTI Knob
Available Values
OFF/100(Hz) ~ 1000(Hz)
6dB/oct / 18dB/oct
700(Hz) ~ 4000(Hz)/OFF
6dB/oct / 18dB/oct
OFF/100(Hz) ~ 1000(Hz)
6dB/oct / 18dB/oct
700(Hz) ~ 4000(Hz)/OFF
6dB/oct / 18dB/oct
OFF/100(Hz) ~ 1000(Hz)
6dB/oct / 18dB/oct
700(Hz) ~ 4000(Hz)/OFF
6dB/oct / 18dB/oct
OFF/100(Hz) ~ 1000(Hz)
6dB/oct / 18dB/oct
700(Hz) ~ 4000(Hz)/OFF
6dB/oct / 18dB/oct
OFF/100(Hz) ~ 1000(Hz)
6dB/oct / 18dB/oct
700(Hz) ~ 4000(Hz)/OFF
6dB/oct / 18dB/oct
Page 47
SSB/AM Mode Transmission
ON/OFF Switch
BAND Button
MODE Button
1. Press the BAND button to shown the band list, then
touch a band key corresponding to the Amateur band
on which you wish to operate.
2. Press the MODE button to show the mode list, then
select the operating mode by touching the corresponding key.
Advice:
By convention, LSB is used in the 7 MHz and lower
Amateur bands for SSB communication, and USB is
used on the 14 MHz and higher bands (the 10 MHz
band is used for CW and data modes only).
3. Rotate the Main Tuning Dial knob to adjust the operating frequency. Alternately, you may use the UP/
DWN scanning buttons on the MH-31A8J Hand Microphone to sweep up or down the current band.
4. Press the microphone PTT (Push To Talk) switch to
begin transmission; speak into the microphone in a
normal voice level.
Advice:
 The “ ” indicator will light up in the LED indicators area, confirming that transmission is in
progress.
 When transmitting in the AM mode, set a maximum (carrier) power output of 25 Watts via
[PROC] displayed by pressing the F(M-LIST)
button.
Page 48
F(M-LIST) Button
MULTI Knob
Main Tuning Dial Knob
5. Adjust the microphone amplifier gain to match the
microphone and your voice level: Touch [METER]
on the LCD repeatedly to select the “ALC”.
Press and hold the PTT switch, and speak into the
microphone in a normal voice level.
In the SSB mode, touch [MIC GAIN] and then adjust MULTI knob so that the ALC meter stays within
the ALC zone of the meter (up to half scale deflection) on voice peaks.
In the AM mode, touch [MIC GAIN] and then adjust
MULTI knob so that the ALC meter does not deflect
at voice peaks.
6. Release the PTT switch at the end of your transmission. The transceiver will return to the receive mode.
FT-991 Operating Manual
SSB/AM Mode Transmission
Advice:
 ALC meter deflection may be caused by excessive
drive power, but also by reflected power detected
in the antenna system. If the impedance presented
to the transceiver is other than 50 Ohms, ALC meter action may be observed that is not related to the
proper setting of [MIC GAIN] on the LCD. Therefore, we recommend that you make [MIC GAIN]
adjustments into a dummy load or antenna system
presenting impedance very close to 50 Ohms.
 When performing “on air” tests (such as the setup of
microphone gain), be sure to check the frequency before transmitting, to avoid interference to others who
may already be using the frequency.
FT-991 Operating Manual
 Four techniques for exercising Transmit/Receive
control are provided on the FT-991. You may
choose the technique(s) that best suit your operating
needs:
 Pressing the microphone PTT switch will engage
the transmitter.
 The rear panel PTT jack may be connected to a
foot switch or other manual switching device in
order to engage the transmitter.
 Touching [MOX] displayed by pressing the F(MLIST) button will lock the transmitter on. Touch
[MOX] on the LCD again to return to receive.
 The VOX (Voice Operated Xmit) circuit will
engage the transmitter automatically when you
speak into the microphone. For details of VOX
operation refer to page ##.
Page 49
Using the Automatic Antenna Tuner
The Automatic Antenna Tuner (hereinafter referred to as the “ATU”) built into each FT-991 is designed to ensure a 50Ohm load for the final amplifier stage of the transmitter. We recommend that the ATU be used whenever you operate on
the FT-991.
Advice:
 Because the ATU of the FT-991 is located inside the station, it only adjusts the impedance presented to the transceiver at the station end of your coaxial cable feedline. It does not “tune” the SWR at the antenna feed point itself.
When designing and building your antenna system, we recommend that every effort be made to ensure a low SWR
at the antenna feed point.
 The ATU of the FT-991 includes 100 memories for tuning data. Eleven of these memories are allocated, one per
Amateur band, so that each band has at least one setting preset for use on that band. The remaining 89 memories are
reserved for the 89 most-recent tuning points, for quick frequency change without the need to retune the ATU.
 The ATU in the FT-991 is designed to match impedances within the range of 16.5 Ohms to 150 Ohms, corresponding to an SWR of 3:1 or less on the 160 through 6 meter amateur bands. Accordingly, simple non-resonant whip antennas, along with random-length wires and the “G5RV” antenna (on most bands) may not be within the impedance
matching range of the ATU.
ATU Operation
1. Use the Main Tuning Dial knob to set the radio to
the desired operating frequency within the Amateur
band.
2. Press the TUNE button momentarily to place the
ATU in the transmit line (no adjustment/tuning will
occur yet). The “TUNER” icon will appear in the
display.
Quick Point:
The momentary press of the TUNE button will turn
the tuner on, and the microprocessor will automatically select the tuning point closest to the current
operating frequency.
3. Press and hold in the TUNE button for one second to
begin automatic tuning. The transmitter will be engaged, and the “TUNER” icon will blink while tuning is in progress. When the optimum tuning point
has been reached, the radio will return to receive,
and the “TUNER” icon will again glow steadily (instead of blinking).
4. To disconnect the ATU from the transmit line, press
the TUNE button momentarily. The “TUNER”
icon will turn off, confirming that the ATU has been
turned off. In the “Off” mode, the transceiver will be
directly connected to the coaxial cable connected to
your antenna, and will respond to whatever impedance is present at the station end of the coax.
Advice:
The ATU circuit is located between the final amplifier
and the rear-panel antenna jack; reception is not affected
by the ATU.
Page 50
TUNE Button
Quick Points:
As shipped from the factory, only one ATU alignment
point is saved on each Amateur band. This was memorized during the final alignment and performance verification stages on the production line.
Note:
Please check the operating frequency before beginning
the tuning process, to be sure you are not interfering
with others who may already be using the frequency.
Terminology:
Antenna Tuner Memories: The microprocessor of the
ATU makes a note of the selected tuning capacitors and
inductors, and stores the data for each 10 kHz window
in which tuning has occurred. This eliminates the need
to re-tune every time you return to a frequency on which
you have already completed the tuning process.
FT-991 Operating Manual
Using the Automatic Antenna Tuner
About ATU Operation
Figure 1 depicts a situation where normal tuning via the ATU has been successfully completed, and the tuning data has
been stored in the ATU memory. The antenna system as seen by the transmitter is shown.
In Figure 2, the operator has changed frequency, and the “HI-SWR” icon has appeared. The operator presses and holds
in the TUNE button for two seconds to begin impedance matching using the ATU.
If a high SWR condition exists (above 3:1), corrective action must be taken in the antenna system to bring the impedance closer to 50 Ohms. The ATU will refuse to memorize settings on frequencies where the SWR exceeds 3:1. A High
SWR may indicate a mechanical failure in the feed system, and can lead to the generation of spurious signals causing
TVI, etc.
Feed Point SWR
Frequency
SWR after ATU Tuning
Figure 1
The “HI-SWR” icon appears on the display
when you transmit on the frequency
Memorized ATU Tuning
SWR: 3.0
Retuned Setting
Frequency
Figure 2
About ATU Memories
SWR (After tuning) Less than 1.5:1
The tuner settings are stored in the ATU memory.
SWR (After tuning) Greater than 1.5:1
Tuning data will not be retained in memory. If you return to the same frequency, the tuning process must be repeated.
SWR (After tuning) Greater than 3:1
The “HI-SWR” icon will light up, and the tuner settings, if achieved, will not be memorized. Please investigate
the high SWR condition and resolve the problem before attempting further operation using this antenna.
FT-991 Operating Manual
Page 51
Enhancing Transmit Signal Quality
Parametric Microphone Equalizer (SSB/AM/FM mode)
The FT-991 includes a unique Three-Band Parametric Microphone Equalizer that provides precise, independent control
over the low, mid and treble ranges in your voice waveform. You may utilize one group of settings when the speech
processor is off and an alternate group of settings when the speech processor is on. The speech processor feature is described in the next chapter.
Quick Point:
The Parametric Equalizer is a unique technique for adjusting the signal quality. The three audio ranges may be adjusted
so precisely, it is possible to craft an audio response that provides a natural and pleasant sound that you may not have
ever experienced before. Alternately, the effective “talk power” can be significantly enhanced.
The aspects of configuration that you may adjust on the Parametric Equalizer are:
Center Frequency: The center frequency of each of the three bands may be adjusted.
Gain:
The amount of enhancement (or suppression) within each band may be adjusted.
Q:
The bandwidth over which the equalization is applied may be adjusted.
Setup of the Parametric Microphone Equalizer
1. Connect the microphone to the MIC jack.
2. Set the RF output power to minimum value.
Advice:
 We recommend that you connect a dummy load
to one of the Antenna jacks, and monitor your
signal on a separate receiver, to prevent interference to other users.
 You will have the best chance of hearing the effects of adjustments if you wear headphones
(connected to the monitor receiver) while listening to your transmitted signal.
3. To adjust the Parametric Microphone Equalizer
while the speech processor is disabled, press the
F(M-LIST) button, then touch [MIC-EQ] to select
“ON”.
To adjust the Parametric Microphone Equalizer with
the speech processor engaged, press the F(M-LIST)
button, then touch [PROC] to select “ON”.
4. Touch [MONI], if you want to listen on the FT-991
internal monitor.
5. Press the MENU(SETUP) button. The Menu list
will appear in the display.
6. Rotate the MULT knob to find the “EQ” Menu area,
containing Menu items “119” through “127”; these
parameters apply to the adjustment of the Parametric
Microphone Equalizer when the speech processor
is disabled. Menu items “128” through “136” apply to the adjustment of the Parametric Microphone
Equalizer when the speech processor is engaged.
Page 52
MENU(SETUP) Button
F(M-LIST) Button
MULTI Knob
7. Touch [ SELECT ] on the LCD, then rotate the
MULT knob to perform adjustments to a particular
Menu item.
8. Press and hold the PTT switch, and speak into
the microphone while listening to the effect of the
changes you are making. Because the overall effect
on the sound will change with each adjustment, you
should make several passes through each adjustment
area, to be sure that you are achieving the optimum
settings.
9. When you have completed all adjustments, touch
[ENTER] on the LCD to save the new settings.
10. Press the MENU(SETUP) button or touch [BACK]
on the LCD to exit to normal operation. If you only
touch [ BACK ] momentarily to exit, none of the
changes you performed will be stored.
Advice:
To roll off excessive bass response in a wide-range studio microphone, try putting a 10 dB null at 100 Hz with
a bandwidth of “1” or “2”, do about a 3 dB null centered
on 800 Hz with a bandwidth of “3,” and then put an 8
dB peak centered on 2100 Hz with a bandwidth of “1.”
These are starting recommendations; each microphone
and user’s voice will be different, often requiring different settings.
FT-991 Operating Manual
Enhancing Transmit Signal Quality
Parametric Microphone Equalizer (SSB/AM/FM mode)
Activating the Parametric Microphone Equalizer
1. Adjust [MIC GAIN] on the LCD, as described on
page ##.
2. Press the F(M-LIST) button, then touch [MIC-EQ]
on the LCD to select “ON”. If you use the Parametric Microphone Equalizer with the speech processor
engaged, press the F(M-LIST) button, then touch
[PROC] on the LCD to select “ON”.
The “MIC EQ” (and “PROC”) will appear in the
display, confirming that the Parametric Microphone
Equalizer is engaged.
3. Press the PTT switch on the microphone, and speak
into the microphone in a normal voice level.
4. To switch the Parametric Microphone Equalizer off,
touch [MIC-EQ] on the LCD again until the “MIC
EQ” icon disappears.
F(M-LIST) Button
3-Stage Parametric Equalizer Adjustments (Speech Processor: “OFF”)
Center Frequency
“119 PRMTRC EQ1 FREQ”
“100” (Hz) ~ “700” (Hz) / “OFF”
“122 PRMTRC EQ2 FREQ”
“700” (Hz) ~ “1500” (Hz) / “OFF”
“125 PRMTRC EQ3 FREQ”
“1500” (Hz) ~ “3200” (Hz) / “OFF”
Parametric Gain
“120 PRMTRC EQ1 LEVEL” (Low) “–20” (dB) ~ “+10” (dB)
“123 PRMTRC EQ2 LEVEL” (Mid) “–20” (dB) ~ “+10” (dB)
“126 PRMTRC EQ3 LEVEL” (High) “–20” (dB) ~ “+10” (dB)
(Low) “1” ~ “10”
Q (Bandwidth)
“121 PRMTRC EQ1 BWTH”
(Mid) “1” ~ “10”
“124 PRMTRC EQ2 BWTH”
(High) “1” ~ “10”
“127 PRMTRC EQ3 BWTH”
3-Stage Parametric Equalizer Adjustments (Speech Processor: “ON”)
Center Frequency
“128 P-PRMTRC EQ1 FREQ” “100” (Hz) ~ “700” (Hz) / “OFF”
“131 P-PRMTRC EQ2 FREQ” “700” (Hz) ~ “1500” (Hz) / “OFF”
“134 P-PRMTRC EQ3 FREQ” “1500” (Hz) ~ “3200” (Hz) / “OFF”
Parametric Gain
“129 P-PRMTRC EQ1 LEVEL” (Low) “–20” (dB) ~ “+10” (dB)
“132 P-PRMTRC EQ2 LEVEL” (Mid) “–20” (dB) ~ “+10” (dB)
“135 P-PRMTRC EQ3 LEVEL” (High) “–20” (dB) ~ “+10” (dB)
Q (Bandwidth)
“130 P-PRMTRC EQ1 BWTH” (Low) “1” ~ “10”
“133 P-PRMTRC EQ2 BWTH” (Mid) “1” ~ “10”
“136 P-PRMTRC EQ3 BWTH” (High) “1” ~ “10”
Parametric Gain
FT-991 Operating Manual
Page 53
Enhancing Transmit Signal Quality
Using the Speech Processor (SSB Mode)
The FT-991 Speech Processor is designed to increase “talk power” by increasing the average power output (via a sophisticated compression technique) and adjusting the audio quality to the menu settings (“128 P-PRMTRC EQ1 FREQ”,
“131 P-PRMTRC EQ2 FREQ”, “134 P-PRMTRC EQ3 FREQ”). The result is improved intelligibility when conditions
are difficult.
1. Adjust [MIC GAIN] on the LCD, as described on
F(M-LIST) Button
page ##.
2. Touch [ METER ] on the LCD to select “COMP”
(Compression) meter.
3. Press the F(M-LIST) button, then touch [PROC] on
the LCD to select “ON”.
The “PROC” will appear in the display, confirming
that the Speech Processor is engaged.
4. Press the PTT switch on the microphone, and speak
MULTI Knob
into the microphone in a normal voice level.
5. Adjust the MULT knob to set the compression level
within the 5 dB to 10 dB range.
6. To switch the Speech Processor off, touch [PROC]
on the LCD once more. The “PROC” will turn off,
confirming that the Speech processor is turned off.
Advice:
 You may adjust the Parametric Microphone Equalizer when the speech processor is engaged, using
Menu Items “128” through “136”. See page ## for
details.
Page 54
FT-991 Operating Manual
Enhancing Transmit Signal Quality
Adjusting the SSB Transmitted Bandwidth (SSB Mode)
For transmission on SSB, a default bandwidth of 2.4 kHz is provided. This bandwidth provides reasonable fidelity along
with good talk power, and is typical of the bandwidth used for decades for SSB transmission. The bandwidth may be
varied by the operator, to provide different levels of fidelity or talk power, according to your preferences.
Here are the steps to adjust the SSB transmit bandwidth:
1. Press the MENU(SETUP) button to engage the
Menu.
2. Rotate the MULTI knob to select Menu item “110
SSB TX BPF”.
3. Touch [ SELECT ] on the LCD, then rotate the
MULTI knob to select the desired bandwidth. The
available selections are: 100-3000 Hz, 100-2900
Hz, 200-2800 Hz, 300-2700 Hz, and 400-2600 Hz.
The default is 300-2700 Hz. A wider bandwidth will
provide greater fidelity. A narrow bandwidth will
compress the available transmitter power into less
spectrum, resulting in more “talk power” for DX
pile-ups.
4. Touch [ENTER] on the LCD to save the new setting.
5. Press the MENU(SETUP) button or touch [BACK]
on the LCD to exit to normal operation.
Advice:
The Transmit Monitor function is a very helpful way to
confirm the effect that changing the bandwidth will have
on fidelity. With [MONI] displayed by pressing the F(MLIST) button, you will be able to hear the difference in
sound quality as you make changes.
FT-991 Operating Manual
MENU(SETUP) Button
F(M-LIST) Button
MULTI Knob
Quick Points:
The higher fidelity associated with wide bandwidth will
be particularly enjoyable on the low bands during local
rag-chew QSOs.
Page 55
Transmitter Convenience Features
Voice Memory (SSB/AM/FM modes: Requires optional DVS-6 and FH-2)
You may utilize the Voice Memory capability of the FT-991 for repetitive messages. The Voice Memory system
includes five memories capable of storing up to 20 seconds of voice audio each. The maximum that any memory can
hold is 20 seconds.
Voice Memory Operation from the FH-2 Remote Control Keypad
You may also utilize the Voice Memory capability of the FT-991 from the optional FH-2 Remote Control Keypad,
which plugs into the rear panel’s REM/ALC jack.
Recording Your Own Voice in Memory
1. Select the LSB, USB, AM, or FM mode using the
front panel MODE button.
2. Adjust [MIC GAIN] on the LCD, as described on
page ##.
3. Press the [MEM] key on the FH-2. A blinking “REC”
icon will appear in the display.
7. Press the FH-2 [MEM] key to terminate the message
storage process.
Checking Your Recording
4. Press any of the FH-2’s keys numbered [1] through
[5] to select that memory storage register.
Advice:
If you do not press the PTT key (see next step) within five seconds, the memory storage process will be
cancelled.
5. Press the microphone’s PTT switch momentarily.
The “REC” icon will glow steadily and recording
will begin.
6. Speak into the microphone in a normal voice level to
record the message (such as “CQ DX, CQ DX, this
is W 6 Delta X-Ray Charlie, W 6 Delta X-Ray Charlie, Over”). Remember that the time limit for recording any message is 20 seconds.
Page 56
1. Be sure that [MOX] and [BK-IN] on the LCD displayed by pressing the F(M-LIST) button are “Off”.
2. Press the FH-2 [1] ~ [5] key (whichever one you just
recorded in). The “PLAY” icon will appear in the
display and you will hear the contents of the Voice
Memory you just recorded.
Advice:
You may adjust the playback level of the recording via
Menu item “009 RX OUT LEVEL”.
FT-991 Operating Manual
Transmitter Convenience Features
Voice Memory (SSB/AM/FM modes: Requires optional DVS-6 and FH-2)
Transmitting the Recorded Message
1. Select the LSB, USB, AM, or FM mode using the
front panel MODE button.
2. Press the front panel F(M-LIST) button, then touch
[BK-IN] on the LCD.
3. Press the FH-2 [1] ~ [5] key (whichever one you
just recorded in). A “PLAY” icon will appear in the
display and the message will be transmitted.
Advice:
You may adjust the transmit (audio) level of the recording via Menu item “010 TX OUT LEVEL”.
FT-991 Operating Manual
Page 57
Transmitter Convenience Features
VOX (SSB/AM/FM Modes: Automatic TX/RX Switching using Voice Control)
Instead of using the microphone PTT switch or [MOX] displayed by pressing the F(M-LIST) button to activate the
transmitter, the VOX (Voice Operated TX/RX Control) system provides hands-free, automatic activation of the transmitter, based on voice input into the microphone.
1. Press the F(M-LIST) button, then touch [VOX] on
the LCD to select “ON”. The “VOX” will appear in
F(M-LIST) Button
MENU(SETUP) Button
the display.
2. Without pressing the PTT switch, speak into the
microphone in a normal voice level. When you start
speaking, the transmitter should be activated automatically. When you finish speaking, the transceiver
should return to the receive mode (after a short delay).
MULTI Knob
3. To cancel VOX and return to PTT operation, touch
[ VOX ] on the LCD once more. The “VOX” will
turn off, signifying that the VOX circuitry has been
turned off.
Advice:
 The VOX Gain may be adjusted to prevent accidental transmitter activation in a noisy environment. To
adjust the VOX Gain:
1) Activate the VOX circuitry, if necessary.
2) Press the MENU(SETUP) button to engage the
Menu mode.
3) Rotate the MULTI knob to select Menu item “143
VOX GAIN”, then touch [SELECT] on the LCD.
4) While speaking into the microphone, rotate the
MULTI knob to the point where the transmitter
is quickly activated by your voice, without background noise causing the transmitter to activate.
5) When you satisfied with the setting, touch [ENTER] on the LCD to save the new setting.
6) Press the MENU(SETUP) button or touch
[BACK] on the LCD to exit to normal operation.
 The “Hang-Time” of the VOX system (the transmit/
receive delay after the cessation of speech) may also
be adjusted via the Menu mode. The default delay is
500 msec. To set a different delay time:
1)		Activate the VOX circuitry, if necessary.
2) Press the MENU(SETUP) button to engage the
Menu mode.
3) Rotate the MULTI knob to select Menu item “144
VOX DELAY”, then touch [ SELECT ] on the
LCD.
4) Rotate the MULTI knob while saying a brief syllable like “Ah” and listening to the hang time for
the desired delay.
5) When you satisfied with the setting, touch [ENTER] on the LCD to save the new setting.
6) Press the MENU(SETUP) button or touch
[BACK] on the LCD to exit to normal operation.
Page 58
 The Anti-Trip setting adjusts the level of negative receiver audio feedback to the microphone, to prevent
receiver audio from activating the transmitter (via
the microphone). This setting can also be adjusted
via Menu item “145 ANTI VOX GAIN”.
 VOX operation may be engaged on either Voice
modes (SSB/AM/FM) or on AFSK-based Data
modes. Use Menu item “142 VOX SELECT” (the selections are “MIC” and “DATA”).
FT-991 Operating Manual
Transmitter Convenience Features
MONITOR (SSB/AM/FM modes)
You may listen to the quality of your transmitted signal using the Monitor feature.
1. Press the F(M-LIST) button, then touch [MONI] on
the LCD. The “MONI” will appear on the TFT display.
2. During transmission, rotate the MULTI knob to adjust the audio level in the Headphones or speaker.
Clockwise rotation of this knob will increase the volume level.
3. To switch the Monitor off again, touch [MONI] on
the LCD once more. Confirming that the Monitor is
now disengaged.
MENU(SETUP) Button
F(M-LIST) Button
MULTI Knob
Advice:
 Because the Monitor feature samples the transmitter IF signal, it can be very useful for checking the
adjustment of the Speech Processor or Parametric
Equalizer on SSB, and for checking the general signal quality on AM and FM.
FT-991 Operating Manual
Page 59
Transmitter Convenience Features
Split-Frequency Operation
A powerful capability of the FT-991 is its flexibility in Split Frequency operation using the VFO-A and VFO-B frequency registers. This makes the FT-991 especially useful for high-level DX-peditions. The Split operation capability is
very advanced and easy to use.
1. Rotate the Main Tuning Dial knob to set the desired
RX frequency.
2. Press the A/B button, then rotate the Main Tuning
Dial knob to set the desired split TX frequency.
3. Press the A/B button, then press the SPLIT button.
The VFO-B frequency will appear in the TFT display and the LED indicators will look like as below:
VFO-A RX Indicator: “ON” (LED glows Green)
VFO-A TX Indicator: “OFF” (LED Off)
VFO-B RX Indicator: “OFF” (LED Off)
VFO-B TX Indicator: “ON” (LED glows Red)
A/B Button
TXW Button
SPLIT Button
During Split operation, the VFO-A register will be used
for reception, while the VFO-B register will be used for
transmission. If you press the SPLIT button once more,
Split operation will be cancelled.
Advice:
 During Split operation, pressing the A/ B button will
reverse the contents of the VFO-A and VFO-B. Press
the A/B button once more to return to the original
frequency alignment.
During
Split operation you may listen to the TX fre
quency temporarily while pressing the TXW button
located on the bottom left of the Main Tuning Dial
knob.
While pressing the TXW button during split operations, the frequency on the transmission side can be
changed.
 It is possible to set different operating modes (for example, LSB and USB) on the two VFOs used during
Split operation.
 During Split operation it is also possible to set VFOA and VFO-B to different Amateur bands if you use
a multi band antenna.
Page 60
Quick Split Operation
The Quick Split feature allows you to set a one-touch
offset of +5 kHz to be applied to your radio’s VFO-B
(transmit) frequency, compared to the VFO-A frequency.
1. Start with regular transceiver operation on the VFO-A.
VFO-A RX Indicator: “ON” (LED glows Green)
VFO-A TX Indicator: “ON” (LED glows Red)
VFO-B RX Indicator: “OFF” (LED Off)
VFO-B TX Indicator: “OFF” (LED Off)
2. Press and hold in the SPLIT button for one second
to engage the Quick Split feature, and apply a frequency 5 kHz above the VFO-A frequency to the
VFO-B frequency register.
The VFO configuration will then be:
VFO-A RX Indicator: “ON” (LED glows Green)
VFO-A TX Indicator: “OFF” (LED Off)
VFO-B RX Indicator: “OFF” (LED Off)
VFO-B TX Indicator: “ON” (LED glows Red)
3. Press and hold in the SPLIT switch for one second
to increment the Sub (VFO-B) frequency another +5
kHz.
Quick Points:
 The operating mode applied to the VFO-B register
will be the same as that in use on the VFO-A register.
 The offset of VFO-B from VFO-A is programmed
via the Menu and is set to +5 kHz at the factory.
However, other offsets may be selected using the following procedure:

1. Press the MENU(SETUP) button to engage the
Menu mode.
2. Rotate the MULTI knob to select Menu item “034
QUICK SPLIT FREQ”.
3. Touch [ SELECT ] on the LCD, then rotate the
MULT knob to select the desired offset. The available selections are –20kHz ~ +20kHz (factory default: +5 kHz).
4. Touch [ENTER] button to save the new setting.
5. Press the MENU(SETUP) button or touch [BACK]
on the LCD to exit to normal operation.
FT-991 Operating Manual
CW Mode Operation
The powerful CW operating capabilities of the FT-991 permit operation using an electronic keyer paddle, a “straight
key”, or a computer-based keying device.
Setup for Straight Key (and Straight Key emulation) Operation
Before starting, connect your key line(s) to the front panel KEY jack. Be sure [BK-IN] displayed by pressing the F(MLIST) button is turned off for now.
1. Press the MODE button, then touch [CW-USB] on
the LCD. The “USB CW” icon will appear in the
display. The “MONI” icon will appear in the TFT
display; and the CW monitor is activated.
Advice:
If you press and hold the MODE button, you will
engage the “CW Reverse” mode, whereby the “opposite” sideband injection is used, compared to the
“normal” sideband. The “LSB CW” icon will appear in the display if you select CW Reverse.
2. Rotate the Main Tuning Dial knob to select the desired operating frequency.
3. Press the F(M-LIST) button, then touch [BK-IN] on
the LCD to engage automatic activation of the transmitter when you close the CW key. The “BK-IN”
icon will appear in the TFT display.
Advice:
 When you close your CW key, the transmitter
will automatically be activated, and the CW carrier will be transmitted. When you release the
key, transmission will cease, and after a brief
delay, receive will be restored. The delay time is
user-programmable per the discussion on page
##.
 As shipped from the factory, the FT-991 TX/RX
system for CW is configured for “Semi-breakin” operation. However, using Menu item “057
CW BK-IN”, you may change this setup for full
break-in (QSK) operation, whereby the switching is quick enough to hear incoming signals in
the spaces between the dots and dashes of your
transmission. This may prove very useful during
contest and traffic handling operations.
4. Operation using your CW key may now proceed.
MODE Button
F(M-LIST) Button
MULTI Knob
 If you set [BK-IN] displayed by pressing the F(MLIST) button to Off, you may practice sending CW
with the sidetone only, without having the signal go
out over the air.
 If you reduce power via [PROC] displayed by pressing the F(M-LIST) button, the ALC meter reading
will increase; this is normal and does not indicate
any problem whatsoever (because increased ALC
voltage is being used to lower the power).
Terminology:
Semi-break-in
This is a pseudo-”VOX” mode used on CW, whereby the closure of the CW key will engage the transmitter, and
release of the key will allow the receiver to recover after a short delay. No signals will be heard during the spaces
between dots and dashes (unless the sending speed is extremely slow).
Full break-in
Full break-in (also known as “Full QSK”) involves very fast switching between transmit and receive, incoming
signals may be heard between the dots and dashes as you send them. This allows you to hear a station that suddenly starts transmitting on your frequency, while you are in the midst of a transmission.
FT-991 Operating Manual
Page 61
CW Mode Operation
Using the Built-in Electronic Keyer
Connect the cable from your keyer paddle to the front panel KEY jack.
1. Press the MODE button, then touch [CW-USB] on
the LCD. The “USB CW” icon will appear in the
display. The “MONI” icon will appear in the TFT
display; and the CW monitor is activated.
Advice:
If you press the “CW” mode, you will engage the
“CW Reverse” mode, whereby the “opposite” sideband injection is used, compared to the “normal”
sideband. The “LSB CW” icon will appear in the
display if you select CW Reverse.
2. Rotate the Main Tuning Dial knob to select the desired operating frequency.
3. Press the F(M-LIST) button, then touch [KEYER]
on the LCD to select “ON”. The “KEYER” will appear in the display, confirming that the built-in Electronic Keyer is now active.
4. Touch [SPEED] on the LCD repeatedly to set the
desired sending speed (4 ~ 60 WPM).
Advice:
 The display will show the keying speed for 3 seconds whenever [SPEED] on the LCD is touched.
When
you press either the “Dot” or “Dash” side

of your paddle, the CW keying tone will automatically be generated.
5. Touch [BK-IN] on the LCD to engage automatic activation of the transmitter when you press either the
“Dot” or “Dash” side of your paddle. The “BK-IN”
icon will appear in the TFT display.
6. CW operation utilizing your paddle may now commence.
Advice:
When you utilize your keyer paddle, the transmitter will automatically be activated, and the CW
characters (or a string of dots and dashes) will be
transmitted. When you release the keyer paddle contacts, transmission will cease, and reception will be
restored after a brief delay. The delay time is userprogrammable, per the discussion on page ##.
Page 62
MODE Button
F(M-LIST) Button
MULTI Knob
 If you set [BK-IN] displayed by pressing the F(MLIST) button to Off, you may practice sending CW
with the sidetone only, without having the signal go
out over the air.
 If you reduce power via [PROC] displayed by pressing the F(M-LIST) button, the ALC meter reading
will increase; this is normal and does not indicate
any problem whatsoever (because increased ALC
voltage is being used to lower the power).
FT-991 Operating Manual
CW Mode Operation
Using the Built-in Electronic Keyer
Full Break-in (QSK) Operation
As shipped from the factory, the FT-991 TX/RX system for CW is configured for “Semi-break-in” operation.
However, this setup may be changed to full break-in (QSK) operation using Menu item “057 CW BK-IN”. With
full break-in QSK, the TX/RX switching is quick enough to hear incoming signals in the spaces between the dots
and dashes of your transmission.
1. Press the MENU(SETUP) button to engage the
Menu.
2. Rotate the MULTI knob to select Menu item “057
CW BK-IN”.
3. Press the [ SELECT ] button, then rotate the
MULTI knob to set this Menu item to “FULL”.
4. When your adjustments are complete, touch [ENTER] on the LCD to save the new setting.
5. Press the MENU(SETUP) button or touch
[BACK] on the LCD to exit to normal operation.
MENU(SETUP) Button
MULTI Knob
A number of interesting and useful features are available during Electronic Keyer operation.
Setting the Keyer Weight (Dot/Dash) Ratio
This Menu item may be used to adjust the dot/dash ratio for the built-in Electronic Keyer. The default weighting
is 3:1 (a dash is three times longer than a dot).
1. Press the MENU(SETUP) button to engage the
Menu.
2. Rotate the MULTI knob to select Menu item “01
3 CW WEIGHT”.
3. Press the [SELECT] button, then rotate the
MULTI knob to set the weight to the desired value. The available adjustment range is a Dot/Dash
ratio of 2.5 ~ 4.5 (default value: 3.0).
4. When your adjustments are complete, touch [ENTER] on the LCD to save the new setting.
5. Press the MENU(SETUP) button or touch
[BACK] on the LCD to exit to normal operation.
FT-991 Operating Manual
MENU(SETUP) Button
MULTI Knob
Page 63
CW Mode Operation
Using the Built-in Electronic Keyer
Selecting the Keyer Operating Mode
The configuration of the Electronic Keyer may be customized independently for the front panel KEY jack of the
FT-991. This permits utilization of Automatic Character Spacing (ACS), if desired. This permits the use of an
electronic keyer via the front jack and a straight key or computer-driven keying line via the rear panel jack.
1. Press the MENU(SETUP) button to engage the
Menu.
2. Rotate the MULTI knob to select Menu item “011
KEYER TYPE”.
3. Press the [ SELECT ] button, then rotate the
MULTI knob to set the keyer to the desired mode.
The available selections are:
The built-in Electronic Keyer is turned
OFF:
off (“straight key” mode).
Dots will be generated automatically
BUG:
by the keyer, but dashes must be sent
manually.
ELEKEY: Both dots and dashes will be generated
automatically when using a paddle.
Same as “ELEKEY” except that the spacACS:
ing between characters is precisely set
by the keyer to be the same length as a
dash (three dots in length)
4. When your adjustments are complete, touch [ENTER] on the LCD to save the new setting.
5. Press the MENU(SETUP) button or touch
[BACK] on the LCD to exit to normal operation.
Page 64
MENU(SETUP) Button
MULTI Knob
ACS
OFF
ACS
ON
Morse
"E" & "T"
Inter-character
スペース
Spacing too short
Morse
"E" & "T"
FT-991 Operating Manual
CW Convenience Features
CW Spotting (Zero-Beating)
“Spotting” (zeroing in on another CW station) is a handy technique to ensure you and the other station are precisely on
the same frequency.
The Tuning Offset Indicator in the display may also be moved so you can adjust your receiver frequency to center the
incoming station on the pitch corresponding to that of your transmitted signal.
Using the Auto Zeroing System
(Only when the optional FFT unit is installed)
Press the F(M-LIST) button, then touch [ZIN] on the
LCD to adjust the receiving frequency to the zero-in automatically while receiving the CW signal.
F(M-LIST) Button
Using the SPOT System
Press the F(M-LIST) button, then touch [SPOT] on the
LCD. Touch [MONI] on the LCD, the Spot tone will be
heard through your speaker. This tone corresponds to the
pitch of your transmitted signal. If you adjust the receiver frequency until the pitch of the received CW signal
matches that of the Spot tone, your transmitted signal
will be precisely matched to that of the other station.
Touch [SPOT] on the LCD again to turn the Spot tone
off.
Advice:
 In a tough DX pile-up, you may actually want to
use the SPOT system to find a “gap” in the spread
of calling stations, instead of zeroing in precisely
on the last station being worked by the DX station.
From the DX side, if a dozen or more operators (also
using Yaesu’s SPOT system) all call precisely on the
same frequency, their dots and dashes merge into a
single, long tone that the DX station cannot decipher.
In such situations, calling slightly higher or lower in
frequency may get your call through.
Quick Points:
 The displayed frequency on CW normally reflects
the “zero beat” frequency of your offset carrier. That
is, if you were to listen on USB on 14.100.00 MHz
to a signal with a 700 Hz offset, the “zero beat” frequency of that CW carrier would be 14.100.70 MHz;
the latter frequency is what the FT-991 displays, by
default. However, you can change the display to be
identical to what you would see on SSB by using
Menu item “060 CW FREQ DISPLAY” and setting
it to “DIRECT FREQ” instead of the default “PITCH
OFFSET” setting.
FT-991 Operating Manual
Page 65
CW Convenience Features
CW Delay Time Setting
During semi-break-in (not QSK) operation, the hang time of the transmitter, after you have finished sending, may be adjusted to a comfortable value consistent with your sending speed. This is the functional equivalent of the “VOX Delay”
adjustment used on voice modes, and the delay may be varied anywhere between 30 msec and 3 seconds via Menu item
“064 CW BK-IN DELAY”.
1. Press the F(M-LIST) button, then touch [BK-IN]
on the LCD to enable CW transmission (Menu item
“057 CW BK-IN” must be set to “SEMI”).
2. Press the MENU(SETUP) button to enter the Menu
mode.
3. Rotate the MULTI knob to select Menu item “058
CW BK-IN DELAY”, then touch [SELECT] on the
LCD.
4. Start sending and rotate the MULTI knob to adjust
the hang time, as you prefer for comfortable operation.
5. When your adjustments are complete, touch [ENTER] on the LCD to save the new setting.
6. Press the MENU(SETUP) button or touch [BACK]
on the LCD to exit to normal operation.
Page 66
MENU(SETUP) Button
F(M-LIST) Button
MULTI Knob
FT-991 Operating Manual
CW Convenience Features
Contest Memory Keyer (Using the Optional FH-2 Remote Control Keypad)
You may also utilize the CW message capability of the FT-991 from the optional FH-2 Remote Control Keypad, which
plugs into the rear panel REM/ALC jack.
Message Memory
Five memory channels capable of retaining 50 characters each are provided (using the PARIS standard for characters
and word length).
Example: CQ CQ CQ DE W6DXC K (19 characters)
-- • -- • ---- • -- -- • -- • ---- • -- -- • -- • ---- • -- -- •• • • ---(C) (Q)
(C) (Q)
(C)
(Q)
(D) (E) (W)
Storing a Message into Memory
1. Press the MENU(SETUP) button to enter the Menu
mode.
2. Rotate the MULTI knob to select the CW Memory
Register into which you wish to store the message;
for now, we are just setting the message entry technique to (Keyer entry).
017 CW MEMORY 1
018 CW MEMORY 2
019 CW MEMORY 3
020 CW MEMORY 4
021 CW MEMORY 5
3. Touch [ SELECT ] on the LCD, then rotate the
MULTI knob to set the selected CW Memory Register to “MESSAGE”. If you want to use your keyer
paddle for message entry on all memories, set all five
Menu items (#017 ~ 021) to “MESSAGE”.
4. Touch [ENTER] on the LCD to save the new setting.
5. Press the MENU(SETUP) button or touch [BACK]
on the LCD to exit to normal operation.
-- ••••
(6)
-- ••
(D)
-- •• -(X)
-- • -- •
(C)
-- • -(K)
MENU(SETUP) Button
MULTI Knob
Terminology:
PARIS Word Length: By convention among CW and
Amateur operators (utilized by ARRL and others), the
length of one “word” of CW is defined as the length of
the Morse Code characters spelling the word “PARIS”.
This character (dot/dash/space) length is used for the
specific definition of code speed in “words per minute”.
Contest Number Programming
Use this process if you are starting a contest, or if you somehow get out of sync with the proper number in the
middle of a contest.
1. Press the MENU(SETUP) button to enter the
Menu mode.
2. Rotate the MULTI knob to select Menu item “016
CONTEST NUMBER”. The current contest number appears on the TFT display.
3. Touch [SELECT] on the LCD, then rotate the
MULTI knob to set the Contest Number to the
desired value.
Advice:
Touch [BACK] on the LCD to cancel the setting.
4. Touch [ENTER] on the LCD to save the new setting.
FT-991 Operating Manual
MENU(SETUP) Button
MULTI Knob
5. Press the MENU(SETUP) button or touch
[BACK] on the LCD to exit to normal operation.
Page 67
CW Convenience Features
Contest Memory Keyer (Using the Optional FH-2 Remote Control Keypad)
Message Memory Programming (Using your Paddle)
1. Set the operating mode to CW.
2. Set [BK-IN] on the LCD to “Off”.
3. Turn the internal Electronic Keyer “On”.
4. Press the [MEM] key on the FH-2. A blinking “REC”
icon will appear in the display.
5. Press any of the FH-2 keys numbered [1] through [5]
to begin the memory storage process, and the “REC”
icon will glow steadily.
Checking the CW Memory Contents
1. Be sure that Break-in is still turned “Off” by [BK-IN]
on the LCD.
2. Touch [MONI] on the LCD to enable the CW monitor.
3. Press the FH-2 [1] ~ [5] key, whichever memory
you just recorded in. You will hear the results in the
sidetone monitor, but no RF energy will be transmitted.
On-The-Air CW Message Playback
1. Touch [BK-IN] on the LCD to enable transmission.
Either Full- or Semi-break-in will be engaged, depending on the setting of Menu item “057 CW BKIN”.
2. Press the FH-2 [1] ~ [5] key, depending on which
CW Memory Register message you wish to transmit.
The programmed message will be transmitted on the
air.
6. Send the desired message using your keyer paddle.
Advice:
If you do not start keying within ten seconds, the
memory storage process will be cancelled.
7. Press the [MEM] key on the FH-2 once more at the
end of your message. Up to 50 characters may be
stored in each of the five memories.
Note:
If you subsequently decide to use the “Text Memory”
technique for memory storage, please note that a message stored using keyer paddle input will not be transferred over when you select “Text Memory technique”
on a particular memory register (the Menu Mode Setting
is set to “TEXT”).
Page 68
FT-991 Operating Manual
CW Convenience Features
Contest Memory Keyer (Using the Optional FH-2 Remote Control Keypad)
TEXT Memory
The five channels of CW message memory (up to 50 characters each) may also be programmed using a text-entry technique. This technique is somewhat slower than when you send the message directly from your keyer paddle, but accuracy of character spacing is ensured. Be sure to enter the character “}” at the end of texts.
Example 1: CQ CQ CQ DE W6DXC K} (20 characters)
The sequential Contest Number (“Count up”) feature is another powerful feature of the CW Memory Keyer.
Example 2: 599 10 200 # K} (15 characters)
Text Memory Storage
1. Press and hold in the MENU(SETUP) button for
one second to enter the Menu mode.
2. Rotate the MULTI knob to select the CW Memory
Register into which you wish to store the message;
we are now setting the message entry technique to
(Text entry).
017 CW MEMORY 1
018 CW MEMORY 2
019 CW MEMORY 3
020 CW MEMORY 4
021 CW MEMORY 5
Advice:
The following texts are programmed to the MEMORY 4 and MEMORY 5 in factory default.
MEMORY 4: DE FT-991 K}
MEMORY 5: R 5NN K}
3. Touch [ SELECT ] on the LCD, then rotate the
MULTI knob to set the selected CW Memory Register to “TEXT”. If you want to use text message entry
on all memories, set all five Menu items (#017 ~
021) to “TEXT”.
4. Touch [ENTER] on the LCD to save the new setting.
5. Press the MENU(SETUP) button or touch [BACK]
on the LCD to exit to normal operation.
MENU(SETUP) Button
MULTI Knob
TEXT CW CODE TEXT CW CODE TEXT CW CODE TEXT CW CODE TEXT CW CODE TEXT CW CODE
SN
AS
AR
OS
IMI
”
AF
´
WG
MIM
KR
KN
DU
SX
KK
AAA
KA
＊
DN
FT-991 Operating Manual
BT
￥（＼）
IQ
AL
Page 69
CW Convenience Features
Contest Memory Keyer (Using the Optional FH-2 Remote Control Keypad)
Text Message Programming
1. Press the MODE button to set the operating mode to
CW.
2. Be sure that Break-in is “Off” with [BK-IN] on the
LCD, if necessary.
3. Press the FH-2 [MEM] key. A blinking “REC” icon
will appear in the display.
6. When the message is complete, add the “}” character
at the end to signify the termination of the message.
7. Press and hold in the FH-2 [MEM] key for one second to exit, once all characters (including “}”) have
been programmed.
Checking the CW Memory Contents
1. Be sure that Break-in is still turned “Off” with [BKIN] on the LCD.
2. Touch [MONI] on the LCD to enable the CW monitor.
3. Press an FH-2 [1] ~ [5] key, whichever memory you
just recorded in. You will hear the results in the sidetone, but no RF energy will be transmitted.
4. Press an FH-2 [1] ~ [5] key to select the desired CW
Memory Register into which you wish to program
the text, the blinking “REC” icon will disappear.
5. Use the FH-2 [ ] and [ ] keys to set the cursor
position and use the FH-2’s [ ] and [ ] keys to
choose the letter/number to be programmed in each
slot of the memory. In the case of the second example on the previous page the “#” character designates the slot where the Contest Number will appear.
Advice:
You may also use the Main Tuning Dial knob and the
MULTI knobs to program the message characters.
Page 70
On-The-Air CW Message Playback
1. Touch [BK-IN] on the LCD to enable transmission.
Either Full-break-in or Semi-break-in will be engaged, depending on the setting of Menu item “063
CW BK-IN”.
2. Press an FH-2 [1] ~ [5] key, depending on which
CW Memory Register message you wish to transmit.
The programmed message will be transmitted on the
air.
FT-991 Operating Manual
CW Convenience Features
Contest Memory Keyer (Using the Optional FH-2 Remote Control Keypad)
Note:
If you subsequently decide to use the “Message Memory” technique for memory storage, please note that the
contents of a message stored using text input will not be
transferred over when you set entry to “Message Memory technique” on a particular memory register (the Menu
Mode Setting is set to “MESSAGE”).
Decrementing the Contest Number
Use this process if the current contest number
gets slightly ahead of the actual number you
want to send (in case of a duplicate QSO, for example).
Press the FH-2 [ DEC ] key momentarily. The
current Contest Number will be reduced by one.
Press of the FH-2 [DEC] key as many times as
necessary to reach the desired number. If you go
too far, use the “Contest Number Programming”
technique described previously.
Transmitting in the Beacon Mode
In “Beacon” mode, it is possible to repeatedly
transmit any message programmed, either via
paddle input, or via the “Text” input method. The
time delay between message repeats may be set
anywhere between 1 and 690 seconds (1 ~ 240
sec (1 sec/step) or 270 ~ 690 sec (30 sec/step))
via Menu item “014 BEACON TIME” If you do
not wish the message to repeat in a “Beacon”
mode, please set this Menu item to “OFF”.
To transmit the message:
1. Touch [BK-IN] on the LCD to enable transmission. Either Full-break-in or Semi-breakin will be engaged, depending on the setting
of Menu item “057 CW BK-IN”.
2. Press an FH-2 [1] ~ [5] key. Repetitive transmission of the Beacon message will begin.
FT-991 Operating Manual
Page 71
FM Mode Operation
Basic Operation
1. Press the MODE button, then touch the corresponding key on the LCD to select the FM operating
mode. The “FM” icon appears in the display.
2. Rotate the Main Tuning Dial knob to select the desired operating frequency. Pressing the microphone
UP or DWN button will cause frequency change in 5
kHz steps.
3. Press the microphone PTT switch to transmit. Speak
into the microphone in a normal voice level. Release
the PTT switch to return to receive.
4. Adjustment of the microphone gain may be accomplished in two ways. At the factory, a default level
has been programmed that should be satisfactory for
most situations. However, using Menu item “077
FM MIC GAIN”, you may set a different fixed value,
or choose the “MCVR” option, which then lets you
use [MIC GAIN] on the LCD to set the microphone
gain in the FM mode.
F(M-LIST) Button
MODE Button
Advice:
 The Transmit Monitor is another helpful way to
verify proper adjustment of the FM MIC Gain. With
[MONI] displayed by pressing the F(M-LIST) button, you will be able to hear the differences in deviation as you make adjustments.
 FM is only used in the 28 MHz, 50 MHz, 144 MHz,
and 430 MHz Amateur bands covered by the FT991. Please do not use FM on any other bands.
Page 72
FT-991 Operating Manual
FM Mode Operation
Repeater Operation
The FT-991 may be utilized on 29 MHz, 50 MHz, 144 MHz, and 430 MHz repeaters.
1. Rotate the Main Tuning Dial knob to the output frequency (downlink) from the repeater.
2. If CTCSS Tone operation is desired/needed, press
the F(M-LIST) button, then touch [TONE] on the
LCD to engage the CTCSS mode.
3. Touch [TONE] on the LCD repeatedly to select the
desired CTCSS mode. If you just need to send the
uplink encoding tone, select “ENC.” For encode/decode operation, choose “T.SQL” instead. The available choices are
“OFF”  “ENC (Tone Encoder)”
 “T.SQL (Tone Squelch)”  “OFF”
4. Rotate the MULTI knob to select the desired CTCSS
Tone to be used. A total of 50 standard CTCSS tones
are provided (see the CTCSS Tone Chart).
5. Press the F(M-LIST) button, then touch [RPT] on
the LCD to select the desired repeater shift direction.
The selections are:
“SIMP”  “+”  “–”  “SIMP”
where “SIMP” represents “Simplex” operation (not
used on a repeater).
6. Press and hold the microphone PTT switch to begin
transmission. You will observe that the frequency
has shifted to correspond to the programming you set
up in the previous steps, and a “t” notation will appear on the “10 Hz” frequency digit while transmitting. Speak into the microphone in a normal voice
level. Release the PTT switch to return to the receive
mode.
MENU(SETUP) Button
F(M-LIST) Button
MULTI Knob
67.0
88.5
114.8
151.4
177.3
203.5
250.3
69.3
91.5
118.8
156.7
179.9
206.5
251.4
CTCSS Tone Frequency (Hz)
71.9
74.4 77.0
79.7
94.8
97.4 100.0 103.5
123.0 127.3 131.8 136.5
159.8 162.2 165.5 167.9
183.5 186.2 189.9 192.8
210.7 218.1 225.7 229.1
82.5
107.2
141.3
171.3
196.6
233.6
85.4
110.9
146.2
173.8
199.5
241.8
Advice:
 The conventional repeater shift used on 29 MHz is
100 kHz, while on the 50 MHz band the shift may
vary between 500 kHz and 1.7 MHz (or more). To
program the proper repeater shift, use Menu items
“083 RPT SHIFT (28MHz)” (28 MHz), “084 RPT
SHIFT (50MHz)” (50 MHz), “085 RPT SHIFT
(144MHz)” (144 MHz), and “086 RPT SHIFT
(430MHz)” (430 MHz) as appropriate.
FT-991 Operating Manual
Page 73
FM Mode Operation
Tone Squelch Operation
You may also use “Tone Squelch” whereby your receiver will be kept silent until an incoming signal modulated with a
matching CTCSS tone is received. The receiver squelch will then open in response to the reception of the required tone.
1. Rotate the Main tuning Dial to the output frequency
(downlink) from the repeater.
2. If CTCSS Tone operation is desired/needed, press
the F(M-LIST) button, then touch [TONE] on the
LCD to engage the CTCSS mode.
3. Touch [TONE] on the LCD repeatedly to choose
“T.SQL” from the available choices of
“OFF”  “ENC (Tone Encoder)”
 “T.SQL (Tone Squelch)”  “OFF”
4. Rotate the MULTI knob to select the desired CTCSS
Tone to be used. Fifty standard CTCSS tones are
provided (see the CTCSS Tone Chart).
5. A “d” notation on the “1 Hz” frequency digit in
the display will indicate that the Tone Decoder is
engaged. A “t” notation on the “1 Hz” frequency
digit while transmitting will indicate that the Tone
Squelch is engaged.
Page 74
MENU(SETUP) Button
F(M-LIST) Button
MULTI Knob
FT-991 Operating Manual
Memory Operation
Convenient Memory functions
The FT-991 contains ninety-nine regular memories, labeled “01” through “99”, nine special programmed limit memory pairs, labeled “P-1L/P-1U” through “P-9L/P-9U”, and five QMB (Quick Memory Bank) memories, labeled “C-1”
through “C-5”. Each stores various settings, in addition to the VFO-A frequency and mode (See below). By default, the
99 regular memories are contained in one group; however, they can be arranged in up to six separate groups, if desired.
Quick Point:
The FT-991 memory channels store the following
data (not just the operating frequency):
 VFO-A Frequency
 VFO-A Mode
 Clarifier status and its Offset Frequency
 ANT status
 IPO status
 Roofing filter status and its Bandwidth
 Attenuator status
 Noise Blanker status
 IF SHIFT and WIDTH status
 CONTOUR status and its Peak Frequency
 DSP Noise Reduction (DNR) status and its
Reduction algorithm selection.
 DSP Notch filter (NOTCH) status
 NAR bandwidth status
 DSP Auto Notch filter (DNF) status
 Repeater Shift Direction
PMS Memory Channels
Regular Memory Channels
99
98
97
03
02
01
P-9L/9U
P-8L/8U
P-7L/7U
P-6L/6U
P-5L/5U
P-4L/4U
P-3L/3U
P-2L/2U
P-1L/1U
QMB Memory Channel
C-1
C-2
C-3
C-4
C-5
QMB (Quick Memory Bank)
The Quick Memory Bank consists of five memories (labeled “Q-1” through “Q-5”) independent from the regular and
PMS memories. These can quickly store operating parameters for later recall.
QMB Channel Storage
1. Tune to the desired frequency on the VFO-A.
2. Press the RCL/STO button. The “beep” will confirm
that the VFO-A contents have been written to the
currently available QMB memory.
RCL/STO Button
If you repeatedly press the RCL/STO button, the QMB
memories will be written in the following order:
Q-2  Q-3  Q-4  Q-5  Q-1.
Once all five QMB memories have data on them, previous data (starting with channel Q-1) will be over-written
on a first-in, first-out basis.
QMB Channel Recall
1. Press the RCL/STO button. The current QMB channel data will be shown on the frequency display area.
The “QMB” icon will also appear and the Memory
Mode indicators in the LED indicators area will illuminate.
2. Repeatedly pressing the RCL/STO button will toggle you through the QMB channels:
Q-2  Q-3  Q-4  Q-5  Q-1.
3. Press the V/M button to return to the VFO or Memory mode.
FT-991 Operating Manual
Advice:
Rotating the Main Tuning Dial knob, or changing the
operating mode, will place the transceiver in the “Memory Tune” mode, which is a temporary “pseudo-VFO”
method of tuning off of a stored memory channel. If you
do not over-write the contents of the current memory
channel, the original contents will not be disturbed by
the initiation of Memory Tune operation.
Page 75
Memory Operation
Standard Memory Operation
The Standard Memory of the FT-991 allows storage and recall of up to 99 memories, each storing frequency, mode,
and a wide variety of status information, detailed previously. Memories may be grouped into as many as six Memory
Groups, and additionally you get nine pairs of band-limit (PMS) memories along with five QMB (Quick Memory Bank)
memories.
Memory Storage
1. Set VFO-A up with the frequency, mode, and status,
the way you want to have it stored.
2. Press the A  M button momentarily; the current
channel number will start blinking in the display and
the “MCK” notation will appear.
3. Rotate the MULTI knob to select the memory channel that you wish to store the data on.
4. Press and hold in the AM button for one second to
store the frequency and other data into the selected
memory channel. A double beep will confirm that
you have held the AM button in long enough.
MULTI Knob
AM Button
Memory Channel Recall
1. Press the V/M button, if necessary, to enter the
“Memory mode”.
2. Press the F(M-LIST) button, then touch [MCH] on
the LCD. A memory channel number and the “MCH”
notation will appear in the display.
3. After touching [MCH] on the LCD, you may rotate
the MULTI knob to select the desired memory channel.
Advice:
To work within a particular Memory Group, press the
F(M-LIST) button, then touch [ GRP ] on the LCD.
Rotate the MULTI knob to select the desired Memory
Group, then touch [ENTER] on the LCD (the “MCH”
notation will appear instead of the “GRP”); you may
now choose the memory channel within the selected
Memory Group.
Page 76
F(M-LIST) Button
MULTI Knob
V/M Button
FT-991 Operating Manual
Memory Operation
Labeling Memories
Standard Memory Operation
You may wish to append an Alphanumeric “Tag” (label) to a memory or memories, to aid in recollection of the channel’s use (such as a club name, etc.). To do this:
1. Press the V/M button, if necessary, to enter the
“Memory Mode”.
2. Press and hold in the F(M-LIST) button.
The data stored in the currently selected memory
channel will be displayed on the TFT.
3. Rotate the MULTI knob to recall the memory channel that you wish to append a label.
4. Touch [TAG] on the LCD.
A blinking cursor will appear on the first digit.
5. Touch a key on the LCD to enter the letters, numbers, or symbols of the desired label.
6. Repeat step 5 to program the remaining letters, numbers, or symbols of the desired label. 18 characters
may be used in the creation of a label.
Use [] and [] on the LCD to set the cursor position and [] on the LCD to erase a letter at the left
of the cursor.
7. When you have completed the creation of the label,
touch [ENT] on the LCD.
8. Press the F(M-LIST) button to save the new setting
and return to normal operation.
MULTI Knob
V/M Button
Checking a Memory Channel Status
Before programming a channel into memory, you can check the current contents of that channel without the danger of
over-writing the channel accidentally.
1. Press the AM button momentarily.
The data stored in the currently selected memory
channel will be displayed on the TFT. However,
since you are only checking the contents of the
memory channel, your radio will not have moved to
the memory channel frequency.
2. Rotate the MULTI knob to select a different memory
channel. To exit from the Memory Check mode,
press the AM button momentarily once more.
Advice:
 While the Memory Check function is engaged, the
memory channel number will blink in the display.
 While operating in the VFO mode, using Memory
Check, you may store the current VFO frequency
into the selected memory by pressing and holding
in the AM button for one second (until the double
beep). Conversely, if you wish to write the contents
of the current memory into the VFO-A register, press
the V/M button.
FT-991 Operating Manual
V/M Button
MULTI Knob
AM Button
Page 77
Memory Operation
Standard Memory Operation
Erasing Memory Channel Data
F(M-LIST) Button
1. Press and hold in the F(M-LIST) button.
2. Rotate the MULTI knob to select the memory channel that you would like to erase.
3. Touch [ERASE] on the LCD.
Advice:
 The FT-991 can not erase the memory channels “01”
(and “501” through “510”: U.S. version).
 If you make a mistake and wish to restore the memory’s contents, just repeat steps (1) through (3) above.
Page 78
MULTI Knob
FT-991 Operating Manual
Memory Operation
Standard Memory Operation
Memory Tune Operation
You may freely tune off from any memory channel in a “Memory Tune” mode, this is similar to VFO operation. So long
as you do not over-write the contents of the current memory, Memory Tune operation will not alter the contents of the
memory channel.
1. Press the V/M button to recall any memory channel.
2. Press the F(M-LIST) button, then touch [MCH] on
the LCD.
3. Rotate the MULTI knob to select the memory channel.
4. Rotate the Main Tuning Dial knob; you will now observe that the memory channel frequency is changing.
Advice:
 During Memory Tune operation, you may change
operating modes, and engage the offset Clarifier,
if desired.
5. Press the V/M button momentarily to return to the
originally memorized frequency of the current memory channel. One more press of the V/M button will
return to VFO operation.
FT-991 Operating Manual
F(M-LIST) Button
MULTI Knob
V/M Button
Note:
Computer software programs utilizing the CAT system
interface port may presume that the transceiver is operating in the VFO mode, for certain features like “band
mapping” and/or frequency logging, because the “Memory Tune” mode so closely resembles the VFO mode.
Be sure that you have the FT-991 operating in a control
mode compatible with your software’s requirements.
Use the VFO mode if you’re not sure.
Page 79
Memory Operation
Memory Groups
Memory channels may be arranged into as many as six convenient groups, for easy identification and selection. For example, you might want to designate memory groups for AM BC stations, short-wave broadcast stations, contest frequencies, repeater frequencies and PMS limits, or any other groupings you like.
Each memory group is capable of holding up to 20 memory channels (except Memory Group 01: it is 19 memory channels, and the Group size is fixed). When a memory channel is grouped, the channel numbers change to correspond to the
chart below:
Memory Group Assignment
1. Press the MENU(SETUP) button to enter the Menu
mode.
2. Rotate the MULTI knob to select Menu item “033
MEM GROUP”.
3. Touch [ SELECT] on the LCD, then rotate the
MULTI knob to set this Menu item to “ENABLE” (the
default setting is “DISABLE”).
4. Touch [ENTER] on the LCD to save the new setting.
5. Press the MENU(SETUP) button or [BACK] on the
LCD to exit. Operation will now be restricted to the
six Memory Groups.
To cancel Memory Group operation, repeat steps (1)
through (4) above, choosing “DISABLE” in step (3).
Advice:
To avoid confusion, note that the PMS memory group
and the PMS memories “P-1L” through “P-9U” will be
so designated.
MENU(SETUP) Button
MULTI Knob
Memory Channel Number
Group Memory “OFF”
Group Memory “ON”
01 ~ 19
1-01 ~ 1-19
20 ~ 39
2-01 ~ 2-20
40 ~ 59
3-01 ~ 3-20
60 ~ 79
4-01 ~ 4-20
80 ~ 99
5-01 ~ 5-20
P-1L/1U ~ P-9L/9U
P-1L/1U ~ P-9L/9U
5M-01 ~ 5M-10
US-1 ~ US-5
Choosing the Desired Memory Group
You may recall memories just within a particular Memory Group, if desired.
1. Press the V/M button, if necessary, to enter the
“Memory” mode.
2. Press the F(M-LIST) button, then touch [GRP] on
the LCD. The “GRP” icon will appear on the display.
3. Rotate the MULTI knob to select the desired Memory Group.
4. Press the F(M-LIST) button, then touch [MCH] on
the LCD. The “MCH” icon will appear on the display.
5. Rotate the MULTI knob to select the desired Memory Channel within the Selected Memory Group.
F(M-LIST) Button
MULTI Knob
V/M Button
Advice:
If no channels have been assigned to a particular Memory Group, you will not have access to that Group.
Page 80
FT-991 Operating Manual
Operation on Alaska Emergency Frequency: 5167.5 kh (U.S. Version Only)
Section 97.401(d) of the regulations governing amateur radio in the United States permit emergency amateur communications on the spot frequency of 5167.5 kHz by stations in (or within 92.6 km of) the state of Alaska. This frequency
is only to be used when the immediate safety of human life and/or property are threatened, and is never to be used for
routine communications.
The FT-991 includes the capability for transmission and reception on 5167.5 kHz under such emergency conditions via
the Menu system. To activate this feature:
1. Press the MENU(SETUP) button to enter the Menu
mode.
2. Rotate the MULTI knob to select Menu item “149
EMERGENCY FREQ TX”.
3. Touch [ SELECT] on the LCD, then rotate the
MULTI knob to select “ENABLE.”
4. Touch [ENTER] on the LCD to save the new setting.
5. Press the MENU(SETUP) button or [BACK] on the
LCD to exit to normal operation. Emergency communication on this spot frequency is now possible.
6. Press the V/M button, as necessary, to enter the
Memory mode.
7. Press the F(M-LIST) button, then touch [MCH] on
the LCD.
8. Rotate the MULTI knob to select the emergency
channel (“EMERGENCY”), which is found between
channels “510” and “01”).
Note:
 The receive-mode CLARIFIER functions normally
while using this frequency, but variation of the transmit frequency is not possible. The full specifications
of the FT-991 are not necessarily guaranteed on this
frequency, but power output and receiver sensitivity
should be fully satisfactory for the purpose of emergency communication.
 If you wish to disable operation capability on the
Alaska Emergency Frequency, repeat the above procedures, but set the Menu item “149 EMERGENCY
FREQ TX” to “DISABLE” in step 3.
 In an emergency, note that a half-wave dipole cut
for this frequency should be approximately 45’3” on
each leg (90’6” total length). Emergency operation
on 5167.5 kHz is shared with the Alaska-Fixed Service. This transceiver is not authorized for operation,
under the FCC Part 87, for aeronautical communications.
You may scan either the VFO or the memories of the
FT-991, and the radio will halt scanning on any frequency with a signal strong enough to open the receiver
squelch.
FT-991 Operating Manual
MENU(SETUP) Button
F(M-LIST) Button
MULTI Knob
V/M Button
Page 81
VFO and Memory Scanning
VFO Scanning
1. Set the VFO-A to the frequency on which you would like to begin scanning.
2. Rotate the RF GAIN knob so that the background noise is just silenced.
3. Press and hold in the microphone UP or DWN button for one second to start scanning in the specified
direction on the VFO frequency.
4. If the scanner halts on an incoming signal, the decimal point between the “MHz” and “kHz” digits of
the frequency display will blink.
Advice:
 If the incoming signal disappears, scanning will
resume in about five seconds.
 On the SSB/CW and SSB-based Data modes, the
scanner will pause on a received signal, then will
step across the signal very slowly, giving you
time to stop the scan, if you like. In these modes
on the VFO, the scanner does not stop, however.
5. To cancel scanning, press the PTT switch.
RF GAIN Knob
Advice:
 If you press the microphone PTT switch during
scanning, the scanner will halt at once. However,
pressing the PTT switch during scanning will not
cause transmission.
 You may select the manner in which the scanner resumes while it has paused on a signal, using Menu
item “037 MIC SCAN RESUME”. The default “TIME”
(5 sec) setting will cause the scanner to resume scanning after five seconds; you may change it, however,
to resume only after the carrier has dropped out.
Page 82
FT-991 Operating Manual
VFO and Memory Scanning
Memory Scan
1. Set the transceiver up in the “Memory” mode by
pressing the V/M button, if necessary.
2. Rotate the RF GAIN knob so that the background
noise is just silenced.
3. Press and hold in the microphone UP or DWN button for one second to start scanning in the specified
direction.
Advice:
 If the scanner halts on an incoming signal, the
decimal point between the “MHz” and “kHz”
digits of the frequency display will blink.
 If the incoming signal disappears, scanning will
resume in about five seconds.
4. To cancel scanning, press the PTT witch.
V/M Button
RF GAIN Knob
Advice:
 During Memory Group operation, only the channels
within the current Memory Group will be scanned.
 If the scan has paused on a signal, pressing the microphone UP or DWN button will cause scanning to
resume instantly.
 If you press the microphone PTT switch during
scanning, the scanner will halt at once. However,
pressing the PTT switch during scanning will not
cause transmission.
 You may select the manner in which the scanner resumes while it has paused on a signal, using Menu
item “037 MIC SCAN RESUME”. During memory
scanning, the default “TIME” (5 sec) setting will
cause the scanner to resume scanning after five
seconds. However, you may change this setting to
resume only after the carrier has dropped out, if you
like.
Quick Point:
If you have no interest in scanning, and wish to prohibit
the microphone UP/DWN buttons from initiating scanning, you may disable scanning control from the microphone using Menu item “036 MIC SCAN” (set it to
“DISABLE”).
FT-991 Operating Manual
Page 83
PMS (Programmable Memory Scanning)
To limit scanning (and manual tuning) within a particular frequency range, you can use the Programmable Memory
Scanning (PMS) feature, which utilizes nine special-purpose memory pairs (“P-1L/P-1U” through “P-9L/P-9U”). The
PMS feature is especially useful in helping you to observe any operating sub-band limits, which apply to your Amateur
license class.
1. Store the Lower and Upper tuning/scanning limit
frequencies into the memory pair “P-1L” and “P-1U”,
respectively, or any other “L/U” pair of memories in
the special PMS memory area. See page ## for details regarding memory storage.
2. Press the V/M button to enter the “Memory” mode.
3. Press the F(M-LIST) button, then touch [MCH] on
the LCD. The LEDs indicating the Memory mode
will illuminate.
4. Rotate the MULTI knob to select memory channel
“P-1L” or “P-1U”.
5. Rotate the RF GAIN knob so that the background
noise is just silenced.
6. Turn the Main Tuning Dial knob slightly (to activate
memory tuning). Tuning and scanning are now limited to the range within the P-1L/P-1U limits until you
press the V/M button to return to memory channel or
VFO operation.
7. Press and hold in the microphone UP or DWN button for one second to start scanning in the specified
direction.
Advice:
 If the scanner halts on an incoming signal, the
decimal point between the “MHz” and “kHz”
digits of the frequency display will blink.
 If the incoming signal disappears, scanning will
resume in about five seconds.
 On the SSB/CW and SSB-based Data modes,
the scanner will pause on a received signal, then
will step across the signal very slowly, giving
you time to stop the scan, if you like. However,
in these modes on the VFO, the scanner does not
stop.
 If the scan has paused on a signal, pressing the
microphone UP or DWN button will cause scanning to resume instantly.
8. If you rotate the Main Tuning Dial knob in the opposite direction from the current scanning direction
(in other words, you rotate the dial to the left when
scanning toward a higher frequency), the direction of
the scan will reverse.
9. If you press the microphone PTT switch during
scanning, the scanner will halt at once. Pressing the
PTT switch during scanning will not cause transmission.
Page 84
F(M-LIST) Button
MULTI Knob
RF GAIN Knob
V/M Button
FT-991 Operating Manual
RTTY (Radio Teletype) Operation
Example of Connecting RTTY Communications Device
Connect the RTTY communications TU (Terminal Unit) to the rear panel RTTY/PKT terminal. Be sure to read the instructions manual of the device to connect when connecting.
See page ## for details on the connections and settings to use the optional USB Interface Unit “SCU-17”.
Advice:
You can adjust RTTY data output level using Menu item
“099 RTTY OUT LEVEL”.
TU
FT-991 Operating Manual
Page 85
DATA (PSK) Operation
Example of Data Communications Device
You can use commercial and free computer software for PSK data communications. See the illustration below for connection to your computer.
Be sure to read the instruction manual of the device to be connected to the radio and computer.
See page ## for details on the connections and settings to use the optional USB Interface Unit “SCU-17”.
Advice:
 You can set the data output level for data communications (PSK31, SSTV, etc.) using Menu item “075
DATA OUT LEVEL”.
 You can set VOX DELAY in VOX operation for data
communications (PSK31, SSTV, etc.) using Menu
item “147 DATA VOX DELAY”. You can also set data
input VOX gain using Menu item “146 DATA VOX
GAIN”.
To LINE IN/MIC IN,
LINE OUT/MIC OUT,
COM port, etc.
Interface device
commercially
available
Page 86
FT-991 Operating Manual
Menu Mode
The Menu system of the FT-991 provides extensive customization capability, so you can set up your transceiver just the
way you want to operate it. The Menu items are grouped by general utilization category, and are numbered from “001
AGC” to “149 E/D PSK”.
Using the Menu
1. Press the MENU(SETUP) button to engage the
Menu mode.
The display will show the Menu Number, the Menu
Group Name and the Menu Item.
2. Rotate the MULTI knob to select the Menu item you
wish to modify.
3. Touch [ SELECT ] on the LCD, then rotate the
MULTI knob to change the current setting of the selected Menu item.
Advice:
Touch [BACK] on the LCD to cancel the setting.
4. When you have finished making your adjustments,
touch [ENTER] on the LCD to save the new setting, then press the MENU(SETUP) button or touch
[BACK] on the LCD to exit to normal operation.
FT-991 Operating Manual
MENU(SETUP Button
MULTI Knob
Page 87
Menu Mode
Group
AGC
No.
Menu Function
001 FAST DELAY
Available Settings
20 ～ 4000 (20msec/step)
Default Value
300msec
AGC
002 MID DELAY
20 ～ 4000 (20msec/step)
700msec
AGC
003 SLOW DELAY
20 ～ 4000 (20msec/step)
3000msec
DISPLAY
004 MY CALL TIME
OFF ～ 5sec
1sec
BLUE/GRAY/GREEN/ORANGE/PURPLE/RED/
DISPLAY
005 DISPLAY COLOR
DISPLAY
006 DIMMER LED
1/2
DISPLAY
007 DIMMER TFT
0 ～ 15
DISPLAY
008 BAR MTR PEAK HOLD
OFF/0.5/1.0/2.0 (sec)
OFF
DVS
009 RX OUT LEVEL
0 ～ 100
50
DVS
010 TX OUT LEVEL
0 ～ 100
50
SKY BLUE/
OFF/BUG/ELEKEY-A/ELEKEY-B/ELEKEY-Y/
BLUE
KEYER
011 KEYER TYPE
KEYER
012 CW KEYER
NOR/REV
NOR
KEYER
013 CW WEIGHT
2.5 ～ 4.5
3.0
KEYER
014 BEACON TIME
OFF/1 ～ 240sec/270 ～ 690sec
OFF
KEYER
015 NUMBER STYLE
1290/AUNO/AUNT/A2NO/A2NT/12NO/12NT
1290
KEYER
016 CONTEST NUMBER
0 ～ 9999
KEYER
017 CW MEMORY 1
TEXT/MESSAGE
TEXT
KEYER
018 CW MEMORY 2
TEXT/MESSAGE
TEXT
KEYER
019 CW MEMORY 3
TEXT/MESSAGE
TEXT
KEYER
020 CW MEMORY 4
TEXT/MESSAGE
TEXT
KEYER
021 CW MEMORY 5
TEXT/MESSAGE
TEXT
GENERAL
022 NB WIDTH
1/3/10msec
3msec
GENERAL
023 NB REJECTION
10/30/50dB
30dB
GENERAL
024 NB LEVEL
0 ～ 100
50dB
GENERAL
025 BEEP LEVEL
0 ～ 100
50
GENERAL
026 TIME ZONE
-12:00 ～ 0:00 ～ +14:00
0:00
GENERAL
027 GPS/232C SELECT
GPS/RS232C
GPS
GENERAL
028 232C RATE
4800/9600/19200/38400 (bps)
4800bps
GENERAL
029 232C TOT
10/100/1000/3000 (msec)
10msec
GENERAL
030 CAT RATE
4800/9600/19200/38400 (bps)
4800bps
GENERAL
031 CAT TOT
10/100/1000/3000 (msec)
10msec
GENERAL
032 CAT RTS
ENABLE/DISABLE
ENABLE
GENERAL
033 MEM GROUP
ENABLE/DISABLE
DISABLE
GENERAL
034 QUICK SPLIT FREQ
-20 ～ +20kHz
5kHz
GENERAL
035 TX TOT
OFF/1 ～ 30 (min)
OFF
GENERAL
036 MIC SCAN
ENABLE/DISABLE
ENABLE
GENERAL
037 MIC SCAN RESUME
PAUSE/TIME
TIME
GENERAL
038 FREQ ADJ
-25 ～ 0 ～ 25
GENERAL
039 CLAR SELECT
RX/TX/TRX
MODE-AM
040 AM LCUT FREQ
OFF/100Hz ～ 1000Hz (50Hz/step)
OFF
MODE-AM
041 AM LCUT SLOPE
6dB/oct / 18dB/oct
6dB/oct
MODE-AM
042 AM HCUT FREQ
700Hz ～ 4000Hz (50Hz/step) / OFF
OFF
MODE-AM
043 AM HCUT SLOPE
6dB/oct / 18dB/oct
6dB/oct
MODE-AM
044 AM MIC SEL
MIC/REAR
MIC
MODE-AM
045 AM MIC GAIN
MCVR/0 ～ 100
30
MODE-AM
046 AM OUT LEVEL
0 ～ 100
50
047 REAR PTT SELECT
DAKY/RTS/DTR
DAKY
048 REAR PORT SELECT
DATA/USB
DATA
ACS
ELEKEY-B
049 AM DATA GAIN
0 ～ 100
50
MODE-CW
050 CW LCUT FREQ
OFF/100Hz ～ 1000Hz(50Hz/step)
250Hz
MODE-CW
051 CW LCUT SLOPE
6dB/oct / 18dB/oct
18dB/oct
Page 88
FT-991 Operating Manual
Menu Mode
Group
MODE-CW
No.
Menu Function
052 CW HCUT FREQ
Available Settings
700Hz ～ 4000Hz(50Hz/step)
Default Value
1200Hz
MODE-CW
053 CW HCUT SLOPE
6dB/oct / 18dB/oct
18dB/oct
MODE-CW
054 CW OUT LEVEL
0 ～ 100
50
MODE-CW
055 CW AUTO MODE
OFF/50M/ON
OFF
MODE-CW
056 CW BFO
USB/LSB/AUTO
USB
MODE-CW
057 CW BK-IN
SEMI/FULL
SEMI
MODE-CW
058 CW BK-IN DELAY
30 ～ 3000 (msec)
200msec
MODE-CW
059 CW WAVE SHAPE
1/2/4/6 (msec)
4msec
MODE-CW
060 CW FREQ DISPLAY
DIRECT FREQ/PITCH OFFSE
PITCH OFFSE
MODE-CW
061 PC KEYING
OFF/DAKY/RTS/DTR
OFF
MODE-CW
062 QSK
15/20/25/30(msec)
15msec
MODE-DATA
063 DATA MODE
PSK/OTHERS
PSK
MODE-DATA
064 PSK TONE
1000/1500/2000(Hz)
1000Hz
MODE-DATA
065 OTHER DISP (SSB)
-3000 ～ 0 ～ +3000(10Hz/step)
0Hz
MODE-DATA
066 OTHER SHIFT (SSB)
-3000 ～ 0 ～ +3000(10Hz/step)
0Hz
MODE-DATA
067 DATA LCUT FREQ
OFF/100 ～ 1000(Hz)(50Hz/step)
300Hz
MODE-DATA
068 DATA LCUT SLOPE
6dB/oct / 18dB/oct
18dB/oct
MODE-DATA
069 DATA HCUT FREQ
700 ～ 4000(Hz)(50Hz/step)/OFF
3000Hz
MODE-DATA
070 DATA HCUT SLOPE
6dB/oct / 18dB/oc
18dB/oct
MODE-DATA
071 DATA IN SELECT
REAR/MIC
REAR
MODE-DATA
072 DATA MIC GAIN
0 ～ 100
50
MODE-DATA
073 REAR PTT SELECT
DAKY/RTS/DTR
DAKY
MODE-DATA
074 REAR PORT SELECT
DATA/USB
DATA
MODE-DATA
075 DATA OUT LEVEL
0 ～ 100
50
MODE-FM
076 FM MIC SEL
MIC/REAR
MIC
MODE-FM
077 FM MIC GAIN
MCVR/0 ～ 100
30
MODE-FM
078 FM OUT LEVEL
0 ～ 100
50
MODE-FM
079 REAR PTT SELECT
DAKY/RTS/DTR
DARY
MODE-FM
080 REAR PORT SELECT
DATA/USB
DATA
MODE-FM
081 FM PKT GAIN
0 ～ 100
50
MODE-FM
082 FM PKT MODE
1200/9600
1200
MODE-FM
083 RPT SHIFT 28MHz
0 ～ 1000kHz (10kHz/step)
100kHz
MODE-FM
084 RPT SHIFT 50MHz
0 ～ 4000kHz (10kHz/step)
1000kHz
MODE-FM
085 RPT SHIFT 144MHz
0 ～ 4000kHz (10kHz/step)
600kHz
MODE-FM
086 RPT SHIFT 430MHz
0 ～ 9990kHz (10kHz/step)
5000kHz
MODE-FM
087 ARS 144MHz
OFF/ON
ON
MODE-FM
088 ARS 430MHz
OFF/ON
ON
089 DCS POLARITY
Tn-Rn/Tn-Riv/Tiv-Rn/Tin-Riv
Tn-Rn
090 AMS TX MODE
AUTO/DN/VW/ANALOG
AUTO
091 RADIO ID
*****
MODE-RTTY
092 RTTY LCUT FREQ
OFF/100Hz ～ 1000Hz (50Hz/step)
300Hz
MODE-RTTY
093 RTTY LCUT SLOPE
6dB/oct / 18dB/oct
18dB/oct
MODE-RTTY
094 RTTY HCUT FREQ
700Hz ～ 4000Hz (50Hz/step) / OFF
3000Hz
MODE-RTTY
095 RTTY HCUT SLOPE
6dB/oct / 18dB/oct
18dB/oct
MODE-RTTY
096 RTTY SHIFT PORT
SHIFT/DTR/RTS
SHIFT
MODE-RTTY
097 POLARITY-R
NOR/REV
NOR
MODE-RTTY
098 POLARITY-T
NOR/REV
NOR
MODE-RTTY
099 RTTY OUT LEVEL
0 ～ 100
50
MODE-RTTY
100 RTTY SHIFT
170/200/425/850 (Hz)
170Hz
MODE-RTTY
101 RTTY MARK FREQ
1275/2125 (Hz)
2125Hz
MODE-SSB
102 SSB LCUT FREQ
OFF/100Hz ～ 1000Hz (50Hz/step)
100Hz
MODE-SSB
103 SSB LCUT SLOPE
6dB/oct / 18dB/oct
6dB/oct
MODE-SSB
104 SSB HCUT FREQ
700Hz ～ 4000Hz (50Hz/step) / OFF
3000Hz
FT-991 Operating Manual
Page 89
Menu Mode
Group
MODE-SSB
No.
Menu Function
105 SSB HCUT SLOPE
Available Settings
6dB/oct / 18dB/oct
Default Value
6dB/oct
MODE-SSB
106 SSB MIC SELECT
MIC/REAR
MIC
MODE-SSB
107 SSB OUT LEVEL
0 ～ 100
50
108 REAR PTT SELECT
DAKY
DAKY
109 REAR PORT SELECT
DATA/USB
DATA
MODE-SSB
110 SSB TX BPF
100-3000/100-2900/200-2800/300-2700/4002600
300-2700
RX-DSP
111 APF WIDTH
NARROW/MEDIUM/WIDE
MEDIUM
RX-DSP
112 CONTOUR LEVE
-40 ～ 0 ～ 20
-15
RX-DSP
113 CONTOUR WIDTH
1 ～ 11
10
RX-DSP
114 IF NOTCH WIDTH
NARROW/WIDE
WIDE
AF-SCOPE
115 DISPLAY MODE
SPECTRUM/WATER FALL
SPECTRUM
OFF
116 START CYCLE
OFF/3/5/10 (sec)
117 START DIAL SPEED
0.25kHz/0.5kHz/1kHz/2kHz/4kHz (sec)
1kHz/sec
118 SPAN FREQ
50/100/200/500/1000 (kHz)
100kHz
TX AUDIO
119 PRMTRC EQ1 FREQ
OFF/100 ～ 700 (100/step)
OFF
TX AUDIO
120 PRMTRC EQ1 LEVEL
-20 ～ 0 ～ +10
TX AUDIO
121 PRMTRC EQ1 BWTH
1 ～ 10
10
TX AUDIO
122 PRMTRC EQ2 FREQ
OFF/700 ～ 1500 (100/step)
OFF
TX AUDIO
123 PRMTRC EQ2 LEVEL
-20 ～ 0 ～ +10
TX AUDIO
124 PRMTRC EQ2 BWTH
1 ～ 10
10
TX AUDIO
125 PRMTRC EQ3 FREQ
OFF/1500 ～ 3200 (100/step)
OFF
TX AUDIO
126 PRMTRC EQ3 LEVEL
-20 ～ 0 ～ +10
TX AUDIO
127 PRMTRC EQ3 BWTH
1 ～ 10
10
TX AUDIO
128 P-PRMTRC EQ1 FREQ
OFF/100 ～ 700 (100/step)
200
TX AUDIO
129 P-PRMTRC EQ1 LEVEL
-20 ～ 0 ～ 10
TX AUDIO
130 P-PRMTRC EQ1 BWTH
1 ～ 10
TX AUDIO
131 P-PRMTRC EQ2 FREQ
OFF/700 ～ 1500 (100/step)
800
TX AUDIO
132 P-PRMTRC EQ2 LEVEL
-20 ～ 0 ～ 10
TX AUDIO
133 P-PRMTRC EQ2 BWTH
1 ～ 10
TX AUDIO
134 P-PRMTRC EQ3 FREQ
OFF/1500 ～ 3200 (100/step)
2100
TX AUDIO
135 P-PRMTRC EQ3 LEVEL
-20 ～ 0 ～ 10
TX AUDIO
136 P-PRMTRC EQ3 BWTH
1 ～ 10
TX GNRL
137 HF TX MAX POWER
5 ～ 100
100
TX GNRL
138 50M TX MAX POWER
0 ～ 100
100
TX GNRL
139 144M TX MAX POWER
0 ～ 50
50
TX GNRL
140 430M TX MAX POWER
0 ～ 50
50
TX GNRL
141 TUNER SELECT
OFF/INTERNAL/EXTERNAL/ATAS/LAMP
INTERNAL
TX GNRL
142 VOX SELECT
MIC/DATA
MIC
TX GNRL
143 VOX GAIN
0 ～ 100
50
TX GNRL
144 VOX DELAY
30 ～ 3000 (msec)
500msec
TX GNRL
145 ANTI VOX GAIN
0 ～ 100
50
TX GNRL
146 DATA VOX GAIN
0 ～ 100
50
TX GNRL
147 DATA VOX DELAY
30 ～ 3000 (msec)
100msec
TX GNRL
148 ANTI DVOX GAIN
0 ～ 100
TX GNRL
149 EMERGENCY FREQ TX
DISABLE/ENABLE
DISABLE
Page 90
FT-991 Operating Manual
Specifications
General
Rx Frequency Range:
30 kHz - 55.999995 MHz
					118 MHz - 163.999995 MHz
					420 MHz - 469.999995 MHz
Tx Frequency Ranges: 			
1.8 MHz - 430 MHz (Amateur bands only)
Frequency Stability:			
±0.5 ppm (after 1 minute @+14 °F to +140 °F [–10 °C to +60 °C])
Operating Temperature Range:		
+14 °F to +122 °F (–10 °C to +50 °C)
Emission Modes:			
A1A, A3E, J3E, F3E, F7W, F1B, F1D, F2D, G1B
Frequency Steps:			
5/10 Hz (SSB, CW), 50/100 Hz (AM, FM)
Antenna Impedance: 			
50 Ohms, unbalanced
16.7 - 150 Ohms, unbalanced (1.8 MHz - 29.7 MHz)
25 - 100 Ohms, unbalanced (50 MHz - 54 MHz)
(Tuner ON, 1.8 MHz - 50 MHz Amateur bands, TX only)
Power Consumption (Approx.):		
Rx (no signal)		
1.8 A
					Rx (signal present)
2.2 A
Tx (HF/50 MHz, 100 W) 22 A, (144/430 MHz, 50 W) 15 A
Supply Voltage: 				
DC 13.8 V ± 15 % (Negative Ground)
Dimensions (WxHxD):			
9.01” x 3.15” x 9.96” (229 x 80 x 253 mm)
Weight (Approx.): 			
9.46 lbs (4.3 kg)
Transmitter
Power Output:				HF/50 MHz: 5 - 100 watts (2.5 - 25 watts AM carrier)
144/430 MHz: 5 - 50 watts (2.5 - 12.5 watts AM carrier)
Modulation Types:			J3E: Balanced,
					A3E: Low-Level (Early Stage),
					F3E: Variable Reactance
					F7W: 4FSK (C4FM)
Maximum FM Deviation:		
±5.0 kHz/±2.5 kHz
Harmonic Radiation: 			
Better than –50 dB (below 30 MHz)
Better than –60 dB (above 30 MHz)
SSB Carrier Suppression:
At least 50 dB below peak output
Undesired Sideband Suppression:		
At least 50 dB below peak output
Bandwidth:				
3 kHz (LSB/USB), 500 Hz (CW), 6 kHz (AM), 16 kHz (FM)
Audio Response (SSB):			
Not more than –6 dB from 300 to 2700 Hz
Microphone Impedance:			
600 Ohms (200 to 10 kOhms)
FT-991 Operating Manual
Page 91
Specifications
Receiver
Circuit Type:				SSB/CW/AM: Triple-conversion Superheterodyne
					FM: Double-conversion Superheterodyne
Intermediate Frequencies:		
69.450 MHz
					9.000 MHz (SSB, CW, AM)
					24 kHz (SSB, CW, AM)
					450 kHz (FM)
Sensitivity:				
SSB/CW (10 dB S+N/N)
0.158 µV (1.8 - 30 MHz) (RF AMP 2 “ON”)
0.125 µV (50 - 54 MHz) (RF AMP 2 “ON”)
0.125 µV (144 - 146 MHz) (RF AMP 2 “ON”)
0.125 µV (430 - 440 MHz) (RF AMP 2 “ON”)
AM (10 dB S+N/N, 30 % modulation @400 Hz)
28 µV (0.1 - 1.8 MHz) (RF AMP 2 “ON”)
2 µV (1.8 - 30 MHz) (RF AMP 2 “ON”)
1 µV (50 - 54 MHz) (RF AMP 2 “ON”)
					FM (12 dB SINAD)
0.5 µV (1.8 - 30 MHz) (RF AMP 2 “ON”)
0.25 µV (50 - 54 MHz) (RF AMP 2 “ON”)
0.18 µV (144 - 146 MHz) (RF AMP 2 “ON”)
0.18 µV (430 - 440 MHz) (RF AMP 2 “ON”)
There is no specification for frequency ranges not listed.
Selectivity (WIDTH: Center): 		
Mode				
–6 dB		
–60 dB
SSB/CW (Width=2.4 kHz)		
2.4 kHz or better 3.6 kHz or less
CW-N (Width =500 Hz)		
0.5 kHz or better 750 Hz or less
AM				
6 kHz or better
15 kHz or less
FM				
12 kHz or better 30 kHz or less
FM-N				
9 kHz or better
25 kHz or less
Image Rejection:			
70 dB or better (1.8 MHz - 50 MHz Amateur bands)
60 dB or better (144/430 MHz Amateur band)
Maximum Audio Output:		
2.5 W into 4 Ohms with 10% THD
Audio Output Impedance:		
4 to 16 Ohms (8 Ohms: nominal)
Conducted Radiation:			
Less than 4000 uuW
Specifications are subject to change, in the interest of technical improvement, without notice or obligation, and are
guaranteed only within the amateur bands.
Page 92
FT-991 Operating Manual
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
1. Changes or modifications to this device not expressly approved by YAESU MUSEN could void the user’s
authorization to operate this device.
2. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions; (1)
this device may not cause harmful interference, and (2) this device must accept any interference including
interference that may cause undesired operation.
3. The scanning receiver in this equipment is incapable of tuning, or readily being altered, by the User to operate
within the frequency bands allocated to the Domestic public Cellular Telecommunications Service in Part 22.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
DECLARATION BY MANUFACTURER
The scanner receiver is not a digital scanner and is incapable of being converted or modified into a digital scanner
receiver by any user.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE
SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
CAN ICES-3 (B) / NMB-3 (B)
FT-991 Operating Manual
Page 93
Copyright 2014
YAESU MUSEN CO., LTD.
All rights reserved
No portion of this manual
may be reproduced without
the permission of
YAESU MUSEN CO., LTD.
Printed in Japan

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Author                          : YAESU MUSEN CO., LTD.
Create Date                     : 2014:10:10 15:19:31+09:00
Keywords                        : FCC, ID:, K6620575X50, IC:, 511B-20575X50
Modify Date                     : 2014:10:10 15:19:44+09:00
Trapped                         : False
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2014:10:10 15:19:44+09:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Title                           : FT-991_User Manual.pdf
Creator                         : YAESU MUSEN CO., LTD.
Document ID                     : uuid:6203c6d4-56b7-4455-b5d6-1ff9b9dcd530
Instance ID                     : uuid:e51428ff-676a-4256-adae-5b12bd8c8e58
Producer                        : Adobe PDF Library 10.0.1
Page Count                      : 53

EXIF Metadata provided by EXIF.tools