ASSALOY SCYPROX3 Microprocessor Controlled Networked Locks User Manual XX XXXX Exhibit Cover

ASSA ABLOY Inc. Microprocessor Controlled Networked Locks XX XXXX Exhibit Cover

Contents

Manual 2 of 3

    5015 B.U. Bowman Drive  Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598   Certification Exhibit     FCC ID:  U4A-SCYPROX3 IC: 6982A-SCYPROX3  FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210  ACS Report Number:  10-0443.W06.11.A   Manufacturer: Assa Abloy Model: S1-PA/PK, S2-PA/PK,                                                   TCIP1-M802/M803, TCWI1-M802/M803     Manual(s)
A7764B01/11Copyright 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written  permission of Sargent Manufacturing Company is prohibited. ProfilePoE Mortise LockInstallation Instructionsv.S1
1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.01/29/111234567Table of ContentsWarning  ...................................................................................2General Description .................................................................3Hardware Specifications .........................................................3Electronic Specifications .........................................................3Installation Wiring Overview ...................................................3Installation Wiring ...................................................................4Parts Breakdown .....................................................................8Lock Installation ....................................................................10Operational Check  ................................................................1789Changes or modifications to this unit not expressly approved by ASSA ABLOY Inc.could void the user’s authority to operate the equipment.1Warning Warning SARGENT Mfg. Co. v.S Series locksets utilizing a door position switch (DPS) are not rated for, or intended for use in life safety applications.!FCC: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equip-ment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio com-munications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.Industry Canada:The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Op-eration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Cet appareillage numérique de la classe A répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
01/29/111-800-810-WIRE • www.sargentlock.com • A7764B       3Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock        General DescriptionThe SARGENT Profile Series v.S1 Mortise Lock is available with either an HID® 125 kHz prox or 13.56 MHz iCLASS® technology reader. It utilizes existing infrastructure and IEEE 802.3af PoE (Power over Ethernet) technology as a proven alternative to traditional access control installations.The  v.S1 is a self-contained microprocessor-controlled access control product with non-volatile memory. It uses the existing network  cable to communicate with access control systems. The v.S1 lock holds a total of 2400 unique users per lock. Using PoE technology coupled with approved third party software, this v.S1 online lock offers a complete, integrated access control system.The Profile Series v.S1 Mortise lock may be used for both indoor and exterior applications.  A weather-protective gasket is recommended for exterior applications.HID and iCLASS are registered trademarks of HID Global Corporation.    Hardware Specifications3Electronic Specifications42Installation Wiring Overview5•  2400 users per lock; 10,000 event audit trail•  Multiple time zone and holiday  access scheduling•  Centralized lock management •  Real time door status monitoring •  First-In unlock configuration, either by time or by user (selectable) •  Lock down capable•  Input Power: PoE Class 2 Device, as defined  by IEEE 802.3af•  Supports HID® 125 kHz prox or 13.56 MHz iCLASS® credentials (26 - 39 bit); supports CSN reads for other common 13.56 MHz cards, including MiFare, DesFire, and Felica•  Complete lockset with on-board memory•  Available with or without keypad •  ADA compliant •  Latch: One-piece stainless steel, 3⁄4"projection•  Deadbolt: One-piece hardened stainless steel•  Guardbolt: Stainless steel, non-handed•  Case - 12 gauge, heavy duty, wrought steel•  Inside lever retracts latch and deadbolt•  UL Listed (3 hr.) •  Handing (RH/LH/RHR/LHR) can be specified  but is easily field-reversible without  disassembling the lock body•  Locks furnished for 1-3/4” doors. Can be fur-nished for other door sizes upon request.  Con-sult factory. •  Wire from EAC Panel to door must be shielded with drain terminated at EAC Panel controllerSupplied by OthersA. PoE Frame harness assemblyB. PoE data hinge from McKinney      (patent pending)C. PoE Door harness* from McKinneyD. Profile Series S1 PoE Lock    * Door width determines lengthNetwork CableNetwork Switch (802.3af) ABCDSurface Mount RJ45
4          1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.01/29/11Profile Series v.S1 PoE Mortise Lock  PoE frame harness assembly (From McKinney)PoE data hinge (Patent Pending) (From McKinney)PoE door harness* (From McKinney)6Installation WiringCable: CAT 5e or higher24 AWG shielded with drain wire4-PinMolex-F Molex-F Molex-MCable: CAT 5e,26 AWG stranded,shielded, 100ohmWiring to TIA-568-B StandardRJ45-M Molex-MRJ45-F Jack Cable: CAT 5e or higher24 AWG shielded, 100ohmApproved SoftwareB-Splice Crimp ConnectorCertified Integrator (CI) supplies and terminates the B-Splice connector and the Male RJ45 connector from harness to  end user provided facility cableSupplied by End UserPoE SwitchPoE LockCeilingSupplied by CIPatch PanelDrain Wire Terminated on RackGroundRing Terminal Secured to Lock  Mounting PlateDrain Wire PoE SwitchTerminated toEarth GroundPatch Cable: Patch Panel to PoE Switch4-Pin DPS: Door Position Switch (cylindrical and exits only) Profile Series v.S1 Online P1 PoE lock* Order of installation may vary.     Refer to appropriate sections for instructions.Frame-SideHarnessAssembly(15' length)24AWG Stranded Wire for Earth Ground inside 15' Frame HarnessCable drain wire concealed in shrink tubingAEDCA BEDCNotes:•  Connectors go on only one way. They cannot placed in an incorrect position.•  Do not force and do not offset connec-tors.•  Be sure they are completely seated (flush).B
01/29/111-800-810-WIRE • www.sargentlock.com • A7764B       5Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock        A  Frame Harness InstallationSuggested installation of components and wire harness supplied by McKinney: RJ45-M Molex-MCable: CAT 5e or higher24 AWG shielded, 100ohmB-Splice Crimp ConnectorCeilingSupplied by CI Cut end / ceiling-side PoE harness: TIA-568-B Standard Wiring1  2  3  4  5  6  7 8Pair Number Wire PIN1 White/Blue White/Blue 5Blue 42 White/Orange White/Orange 1Orange 23 White/Green White/Green 3Green 64 White/Brown White/Brown 7Brown 8Do not confuse pair numbers with pin numbers. A pair number is used for reference only (e.g.: 10Base-T Ethernet uses pairs 2 & 3). The pin numbers indicate actual physical locations on the plug and jack.1.  Feed cut end of harness into hole on hinge-side through single access hole. 2.  Push one of the connectors back through hole and feed into separate  access hole.Hinge side of PoE harness:BEach of the hinge-side harness connectors should end up threaded through a different access hole and matched to the same size pin connector from the door harness:•  4-pin male Molex connector.•  6-pin male Molex connector with ground wire.Frame-SideHarnessAssembly(15' length)24AWG Stranded Wire for Earth Ground inside 15' Frame HarnessCable drain wire concealed in shrink tubing6-pin F4-pin M6-pin M4-pin FDrain WireFrame PoE Hinge (Patent Pending)PoE Data Hinge Hinge-side harness connectors:•  4-pin male molex connector•  6-pin male molex connector with ground wireLock-side harness connectors:•  Ring terminal•  (2) 4-pin connectors •  4-pin Molex connector•  4-pin connectorB
6          1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.01/29/11Profile Series v.S1 PoE Mortise Lock  Door Harness InstallationOrder of installation may vary.  Refer to appropriate sections for instructions. 1.  Prop door open.2.  Tape the two lock-side 4-pin connectors to the ring terminal.3.  Using the ring terminal, carefully fish the assembly through the door channel to the lock. 4.  Remove tape from ring terminal and door harness connectors. Hinge-side harness connectors:•  4-pin male Molex connector•  6-pin male Molex connector with ground wireLock-side harness connectors:•  Ring terminal•  (2) 4-pin connectors:•  4-pin Molex connector•  4-pin connectorCGround4-Pin MolexJST4-Pin6-pin MCable: CAT 5e,26 AWG stranded,shielded, 100ohmRing Terminal Secured to Lock Mounting PlatePoE LockC4-pin FDrain WireDJST 4-PinFrom Hinge Connectors  From Lock bodyGround Ring TerminalInside of Door
01/29/111-800-810-WIRE • www.sargentlock.com • A7764B       7Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock        PoE Lock Wiring DDX NC (GREEN/WHITE)RX COM (WHITE)RX NC (GREEN)DX (WHITE/BLACK)LX NO (RED/YELLOW)LX COM (RED/GREENMotor B (BLACK) Motor A (RED)TB1E1 TB2Controller Board Connectors  (Inside Escutcheon)8765432112345678From Lock Body(+) 9VDC (RED) (-) (BLACK)AX/DPS NC (PINK) AX/DPS COM (VIOLET) UnusedUnusedUnusedEGND (GREEN)DPSJ7, J4 JST Connectors(From  Hinge)  Ground Ring Terminal(From Hinge to Top Left Escutcheon Screw)D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4D10JP3C5C37U4D9U1R24R4C10R21TP8C31L1U2D7DN1C12R8D2R5C4J7C16C34U3R14JP4C18R22C6Q1C11TP1TP2J5R10D11DN2T2C1TP3R3D5R1TP4C2TP7C32TP5R7TP6C9R13C35R9C3R2D4C8R23TP9R12 C19R25C15R11C20DN3D6C13C7D1C33J2R6D3C14T1J3C36C17MTG2MTG3MTG4MTG1J6C21J8R15R16J4TB1 E1 TB2PowerRing Terminal  From TrimDPS
8          1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.01/29/11Profile Series v.S1 PoE Mortise Lock  6Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS574899916379210911211131514156
01/29/111-800-810-WIRE • www.sargentlock.com • A7764B       9Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock        1 Outside Lever Reference 8200 Catalog for available levers 12 Inside Lever Reference 8200 Catalog for available levers 13 82-0493 O/S Escutcheon only with Cylinder 182-0495 O/S Escutcheon only without Cylinder 14 82-0492 Inside Escutcheon only without Thumb Turn 182-4571 Inside Escutcheon only with Thumb Turn 1552-2431 125 kHz Prox Only Bezel Assembly (PA)152-2432 Keypad and 125kHz Prox Bezel Assembly (PK)           OR52-4420 13.56 MHz iCLASS Only Bezel Assembly (S1-IA)13.56 MHz reader assembly ships configured for PoE/Hardpower use.52-4421 Keypad and 13.56 MHz Bezel Assembly (S1-IK)13.56 mHz reader assembly ships configured for PoE/Hardpower use.6 52-4424 S1 Controller Assembly (Double Pulse) 17 52-3855 Battery Cover Assembly 18 01-1212 Security Screw 19 52-2427 Profile Screw Pack - Specify Finish (Includes: Fire Stop Plate, Trim Mounting Screws, Security Allen Wrench)110 Consult Factory Lever Handle Screw (Depends on Lever Style) 111 Consult Factory Inside Adapter Assembly (Depends on Lever Style) 112 Consult Factory Outside Adapter Assembly (Depends On Lever Style) 113 S1-82276-hand-finish Lockbody with Dead Bolt with Cylinder 1S1-82277-hand-finish Lockbody with Dead Bolt without CylinderS1-82278-hand-finish Lockbody without Dead Bolt with CylinderS1-82279-hand-finish Lockbody without Dead Bolt without Cylinder14 82-0084 Faceplate with Dead Bolt (shown) 182-0081 Faceplate without Dead Bolt 115 77-4336 Mortise Screw Pack - Specify Finish (Includes: Wood and Me-tal Lock body Screws, Faceplate Screws, and Strike Screws)116 Consult Factory #43 Mortise Cylinder 1   ITEM PART NO. DESCRIPTION QTY.Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS, continued
10          1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.01/29/11Profile Series v.S1 PoE Mortise Lock  Stand on outside of locked door when determining door hand.B. Door PreparationOutside of Door Inside of DoorStep #1 – Door PreparationA. Verify Hand and Bevel of DoorLock InstallationRibbon Cable Hole (Controller to Keypad)Outside of Cylinder Hole(only with cylinder installation)Lever Handle HoleThrough-bolt HoleRibbon Cable Hole  (Controller to Keypad)Inside of Lockbody Wire Hole(only with cylinder installation)Lever Handle Hole*RacewayThrough-bolt HolePre-drilled and/orTapped HolesMortisedPocketPrior to installation, all holes must be free of burrs, debris and sharp edges. Prepare door according to appropriate template (see website www.intelligentopenings.com):•  Manufacturer Door Template: 4533LH Left Hand Hinges Left Open Inward LHRB Left Hand Reverse Bevel Hinges Left Open Outward RHRight Hand Hinges Right Open Inward RHRB Right Hand Reverse Bevel Hinges Right Open Outward 8*Note:  Raceway placement in document is approximate. Thumb Turn Lever HoleFig. 1AFig. 1B
01/29/111-800-810-WIRE • www.sargentlock.com • A7764B       11Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock        Step #2 – How to Change Hand of LockbodyBeveled surface of latchbolt must face strike.The deadlatch is self adjusting.To change the hand of the latchbolt:1.  Insert the blade of a slotted screwdriver (>1/4”) into the spade shape slot behind latch.2.  Rotate the screwdriver 90° to push latchbolt out until back of bolt clears lock case front.3.  Rotate latchbolt 180° until the latchbolt  drops back into the lockbody.Note: Latch cannot be unscrewed.Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A):1.  Position lock body with red surface of locking piece visible.2.  Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body.3.  Rotate the locking piece 180° until RED surface is on opposite side.Note: Red indicates locked side (outside).  Wire harness MUST exit through the  inside/non-cylinder side of the lockbody.B. Retaining RingMake sure the plastic retaining ring is seated  correctly (Fig. 2B):1.  The wires and the plastic retaining ring  must be located on the non-cylinder side.2.  Orient the plastic retaining ring so that the word  Bottom is located at the bottom of the cylinder hole.3.  Route the wires from the top of the cylinder hole into the slot on the top of the plastic retaining ring,  NOT through the retaining ring.Push InRight Hand ShownLocking Guide SlotFig.  2AFig. 2CA. Reverse Lock HandC. Reverse Latch HandRed Locking Piece  Indicates Locked SidePlastic  Retaining RingOutside of DoorFig.  2BSlot
12          1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.01/29/11Profile Series v.S1 PoE Mortise Lock  Step #3 – Install Lockbody1.  Feed the wires first through the mortise pocket and out the inside prep, followed by the lock-body (Fig. 3A).Note: Connectors and wires must be fed through non-cylinder side. 2.  The wires from the lockbody exit the inside door prep through the mortise cutout.3.  Loosely secure the lockbody in the door with two #12 x 1-1/4” wood screws or #12-24 x 1/2” machine screws.Note: Do not completely tighten at this time.Ground Wire(2) 4-Pin Connectors From Hinge (2) #12-24 x 1/2” Long Flat Head Screws for Metal Doors(2) #12 x 1-1/4” Long Flat Head Screws for Metal DoorsFig.  3AMortise Connectors Inside of DoorStep #4 – Door OptionsA. Fire Stop Plate (P/N 52-0033)Fire-rated doors require a fire stop plate on the outside of the door (Fig. 4A).1.  Drill (2) 1/8" x 1-1/4" deep holes in the door if not already present.Refer to template for fire-stop  prep locations.2.  Attach with flap up and  out using (2) #8 x 1/2”  self-tapping screws for  wood and metal doors. B. Weather Conduit (52-2847)Install weather conduit on  NON FIRE-RATED exterior doors only (Fig. 4B). 1.  Carefully insert the weather conduit into the  ribbon cable hole on the inside of the door.2.  Place the O-ring around the weather conduit  on the outside and up against the door (Fig. 4C) Outside of Door(2) 1/8” Diameter Holes RequiredFire Stop Plate(2) #8 Self-Tapping Screws for Wood  and Metal Doors(2) Through-bolt HolesFig. 4AOutside of DoorFig.4BFig.4CRibbon Cable HoleO-Ring
01/29/111-800-810-WIRE • www.sargentlock.com • A7764B       13Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock        Step #6 – Install Outside Escutcheon and Lever Assembly 1A.  For fire rated doors, feed ribbon cable with connector and ground wire from         outside of door through weatherseal gasket and fire stop plate (Fig. 6A).       Note: Install ribbon cable with cable exiting down1B.  For non-fire rated doors, feed ribbon cable with connector and ground         wire from outside of door through weatherseal gasket (if used)         and weather conduit (Fig. 6A).       Note: Install ribbon cable with cable exiting down2.    With outside lever horizontal, locate the outside escutcheon on the door,        while directing the mounting posts through the door and lock body (Fig. 6B).       Make sure the lever spindle is properly engaged in lock.3.    On the inside of the door, insert spindle into square hole         of mortise lock.4.    Slide inside adapter and plate         assembly over spindle and loosely        secure with 2 through bolt         screws (#8-32 x 5/8”).       Note: For 8276 and 8278,        loosely thread cylinder         through escutcheon         and into the lock body         before tightening the        lock case screws         and escutcheon         through bolts.    Gasket 82-0500Step #5 – Install Gasket (for Exterior Doors)1.  Carefully remove the backing from the gasket. 2.  Apply gasket to escutcheon:•  Starting in one place, press the adhesive side  of the gasket firmly against the escutcheon.•  Work around the escutcheon, pressing the sticky side  of the gasket firmly against the escutcheon edge.•  The gasket should be aligned so that all edges of the escutcheon are covered.3.  Attach escutcheon to the door after the wires  are connected.Note: The 43 cylinder may be used with or without a gasket.Fig.  5AInside of DoorMortise Lock bodyand AX ConnectorsFig.  6BReader Cable Ground Wire (E1)Antenna (iCLASS)JST 4-PinFrom Hinge Ground Ring TerminalAntenna  (iCLASS only)Fig.  6AOutside of DoorKeypad RibbonCable Ground Wire (E1)Keypad RibbonCable Ground Wire  (E1)GasketAntenna(iCLASS) OnlyFig.  5B
14          1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.01/29/11Profile Series v.S1 PoE Mortise Lock  Step #7 – Escutcheon Wire ConnectionsImages are shown without gasket. If gasket is necessary,  refer to Step #5. Before the controller is attached to the door:1.  Attach the reader assembly  ribbon cable into the back of the  controller assembly (side that  faces towards the door when  mounted (Fig. 7C Detail). 2.  Attach the antenna to the  circuit board in the plastic  housing under the  controller assembly. Note: The difference between  the wiring for the iCLASS 13.56  MHz reader and the 125 kHz  Prox is that the iCLASS wiring  includes an antenna wire.3.  Attach the ground wire  to the bottom of the  controller assembly  (E1, Fig. 7A).Step #8 – Additional Wiring ConnectionsLock, DPS and raceway wire connections: 1.  Connect the cable from the mortise lock  to the bottom of the controller  assembly (TB1, Fig. 8A).2.  Connect the AX/DPS connector to the 2-pin harness. 3.  Push the two connectors from the  raceway over the controller assembly,  through the gap between the  plastic controller assembly  and the escutcheon,  to the front of the  circuit board. Mortise ConnectorGround WireFig.  8ABackAX/DPSInside of DoorGround Ring Terminal132Outside  EscutcheonAntenna (iCLASS only)UnusedTB1Reader CableGround WireFig.  7A2Outside Escutcheon123Ground WireReader CableAntenna(iCLASS)1Ground Ring Terminal34-Pin  Connectors From Hinge 2Antenna (iCLASS only)Reader Cable14-Pin Connectors From Hinge
01/29/111-800-810-WIRE • www.sargentlock.com • A7764B       15Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock        Step #9 – Ciruit Board Wiring Before installing escutcheon, route raceway cables and ground attach to front of circuit board. Turn the controller assembly over:1.  Route the raceway connectors over the top of the controller assembly and plug into the front of the circuit board (side that faces out when mounted (J7, J4; Fig. 9A).2.  Route the 2 ground ring terminals, one from the lock and the other from the hinge wiring, over the top of the controller assembly and con-nect both to the top escutcheon screw. Note: Connectors go on only one way. Do not offset connectors and make sure they are completely seated.Inside of DoorGround Ring TerminalFig. 9AStep #10 – Install Inside Escutcheon1.  Gently fold the excess ribbon connector and ground wire into the top hole, JST connectors and ground wire into offset middle hole, and mortise and AX/DPS wires into bottom hole, being careful not to pinch wires (Fig. 10A). 2.  Insert (2) #8-32 x 1-1/4" screws through inside escutcheon and thread into outside escutcheon (Fig. 10B)Straighten escutcheons and tighten securely.Inside of DoorFig.  10BFig.  10A
16          1-800-810-WIRE • www.sargentlock.com • A7764BCopyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.01/29/11Profile Series v.S1 PoE Mortise Lock  1.  Slide lever handle onto spindle until fully seated (Fig. 11A).2.  Tighten the set screw securely with 1/8” hex wrench.Step #11 – Install Inside LeverStep #12 – Install and Secure Cylinder1.  Slide cylinder through the spring and  rosette/collar  and screw into lockbody, rotating the cylinder  clockwise (Fig. 12A).Cylinder should be flush with rosette/collar.Note: SARGENT logo must be horizontal and on  the top of the cylinder (Fig. 12B). 2.  Secure the cylinder by tightening cylinder clamp screw located above the deadbolt using #2 Phillips screwdriver (Fig. 12C).3.  Using the key, test cylinder functions: •  8278 Function: Key retracts latch-.•  8276 Function: Key retracts latch and projects  and retracts deadbolt-.Fig.  12AKeyType 43 CylinderCylinder Clamp Screw#2 Phillips Screwdriver Outside of DoorFig.  12CInside LeverFig.  11AInside of DoorSpindleSet ScrewFig.  12BPosition cylinder so that the SARGENT logo is right-side up.Correct            Incorrect
01/29/111-800-810-WIRE • www.sargentlock.com • A7764B       17Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.Profile Series v.S1 PoE Mortise Lock        Step #13 – Attach Front PlateAttach front plate with (2) flat head screws.1A. For 8276- and 8278- function mortise locks with cylinders:•  Insert key into cylinder and rotate.There should be no friction against lock case,  wire harness or any other obstructions. Refer to Section 6, Step 8 Wiringif harness friction exists).•  Check that the key retracts the latch: The key should rotate freely.1B.   For 8276- and 8277- function:•  Throw the deadbolt:Check that the key retracts both the  deadbolt and the latch.•  Try the inside lever:Ensure it retracts latch and deadbolt (if provided).2.  Use a prox 125 kHz or 13.56 MHz iCLASS credential,  or keypad PIN code set up with the Network and Lock Configuration Tool to unlock outside lever and retract latch. Refer to Network Lock and Configuration Tool user manual (WFMN1D) for information on how to configure and program v.S1 locks.Operational Check 9Fig.  13AOutside of DoorFront Plate(2) Flat Head ScrewsLock body Screws
SARGENT Manufacturing100 Sargent DriveNew Haven, CT 06511 USA800-810-WIRE (9473) • www.sargentlock.comFounded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,electro-mechanical products and access control systems for new construction, renovation, and replacement applications.The company’s customer base includes commercial construction, institutional, and industrial markets.Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.ASSA ABLOY is the global leader in door opening solutions, dedicated tosatisfying end-user needs for security, safety and convenience. A7764B-01/11

Navigation menu