ASSALOY SCYPROX3 Microprocessor Controlled Networked Locks User Manual XX XXXX Exhibit Cover
ASSA ABLOY Inc. Microprocessor Controlled Networked Locks XX XXXX Exhibit Cover
ASSALOY >
Contents
- 1. Manual 1 of 3
- 2. Manual 2 of 3
- 3. Manual 3 of 3
Manual 2 of 3
Certification Exhibit FCC ID: U4A-SCYPROX3 IC: 6982A-SCYPROX3 FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0443.W06.11.A Manufacturer: Assa Abloy Model: S1-PA/PK, S2-PA/PK, TCIP1-M802/M803, TCWI1-M802/M803 Manual(s) 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 v.S1 Profile PoE Mortise Lock Installation Instructions A7764B 01/11 Copyright 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. 01/29/11 Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Table of Contents Warning . ..................................................................................2 General Description..................................................................3 Hardware Specifications..........................................................3 Electronic Specifications..........................................................3 Installation Wiring Overview....................................................3 Installation Wiring....................................................................4 Parts Breakdown......................................................................8 Lock Installation.....................................................................10 Operational Check .................................................................17 Warning Changes or modifications to this unit not expressly approved by ASSA ABLOY Inc. could void the user’s authority to operate the equipment. FCC: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Industry Canada: The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe A répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée. Warning SARGENT Mfg. Co. v.S Series locksets utilizing a door position switch (DPS) are not rated for, or intended for use in life safety applications. 1-800-810-WIRE • www.sargentlock.com • A7764B Profile Series v.S1 PoE Mortise Lock General Description The SARGENT Profile Series v.S1 Mortise Lock is available with either an HID® 125 kHz prox or 13.56 MHz iCLASS® technology reader. It utilizes existing infrastructure and IEEE 802.3af PoE (Power over Ethernet) technology as a proven alternative to traditional access control installations.The v.S1 is a self-contained microprocessor-controlled access control product with non-volatile memory. It uses the existing network cable to communicate with access control systems. The v.S1 lock holds a total of 2400 unique users per lock. Using PoE technology coupled with approved third party software, this v.S1 online lock offers a complete, integrated access control system. The Profile Series v.S1 Mortise lock may be used for both indoor and exterior applications. A weather-protective gasket is recommended for exterior applications. HID and iCLASS are registered trademarks of HID Global Corporation. • • Complete lockset with on-board memory Available with or without keypad ADA compliant Latch: One-piece stainless steel, 3⁄4"projection Deadbolt: One-piece hardened stainless steel Guardbolt: Stainless steel, non-handed Case - 12 gauge, heavy duty, wrought steel Inside lever retracts latch and deadbolt UL Listed (3 hr.) Handing (RH/LH/RHR/LHR) can be specified but is easily field-reversible without disassembling the lock body Locks furnished for 1-3/4” doors. Can be furnished for other door sizes upon request. Consult factory. Wire from EAC Panel to door must be shielded with drain terminated at EAC Panel controller Electronic Specifications • • 2400 users per lock; 10,000 event audit trail Multiple time zone and holiday access scheduling Centralized lock management Real time door status monitoring First-In unlock configuration, either by time or by user (selectable) Lock down capable Input Power: PoE Class 2 Device, as defined by IEEE 802.3af Supports HID® 125 kHz prox or 13.56 MHz iCLASS® credentials (26 - 39 bit); supports CSN reads for other common 13.56 MHz cards, including MiFare, DesFire, and Felica • • • • • • Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Hardware Specifications • • • • • • • • • • Installation Wiring Overview Supplied by Others Network Cable Surface Mount RJ45 Network Switch (802.3af) A. PoE Frame harness assembly B. PoE data hinge from McKinney (patent pending) C. PoE Door harness* from McKinney D. Profile Series S1 PoE Lock * Door width determines length 1-800-810-WIRE • www.sargentlock.com • A7764B 01/29/11 Profile Series v.S1 PoE Mortise Lock 6 Installation Wiring PoE frame harness assembly (From McKinney) D DPS: Door Position Switch (cylindrical and exits only) PoE data hinge (Patent Pending) (From McKinney) PoE door harness* (From McKinney) Profile Series v.S1 Online P1 PoE lock * Order of installation may vary. Refer to appropriate sections for instructions. Supplied by CI Supplied by End User Certified Integrator (CI) supplies and terminates the B-Splice connector and the Male RJ45 connector from harness to Patch Cable: end user provided facility cable Patch Panel to PoE Switch B-Splice Crimp Connector PoE Switch Drain Wire RJ45-M RJ45-F Jack 01/29/11 24AWG Stranded Wire for Earth Ground inside 15' Frame Harness FrameSide Harness Assembly (15' length) Cable drain wire concealed in shrink tubing Cable: CAT 5e or higher 24 AWG shielded with drain wire Cable: CAT 5e or higher 24 AWG shielded, 100ohm Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Ceiling Patch Panel Drain Wire Terminated on Rack Approved Software Cable: CAT 5e, 26 AWG stranded, shielded, 100ohm Molex-M PoE Switch Terminated to Earth Ground 4-Pin Notes: • Connectors go on only one way. They cannot placed in an incorrect position. • Do not force and do not offset connectors. • Be sure they are completely seated (flush). 4-Pin Molex-F Molex-M Molex-F PoE Lock Ground Ring Terminal Secured to Lock Mounting Plate Wiring to TIA-568-B Standard 1-800-810-WIRE • www.sargentlock.com • A7764B Profile Series v.S1 PoE Mortise Lock Frame Harness Installation Cut end / ceiling-side PoE harness: Supplied by CI Suggested installation of components and wire harness supplied by McKinney: B-Splice Crimp Connector TIA-568-B Standard Wiring 3 4 5 6 7 Pair Number White/Blue White/Orange RJ45-M Ceiling White/Brown White/Blue Blue White/Orange Orange White/Green Green White/Brown Brown Do not confuse pair numbers with pin numbers. A pair number is used for reference only (e.g.: 10Base-T Ethernet uses pairs 2 & 3). The pin numbers indicate actual physical locations on the plug and jack. Hinge side of PoE harness: 1. Feed cut end of harness into hole on hinge-side through single access hole. 2. Push one of the connectors back through hole and feed into separate access hole. Molex-M Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Cable drain wire concealed in shrink tubing White/Green PIN Each of the hinge-side harness connectors should end up threaded through a different access hole and matched to the same size pin connector from the door harness: • 4-pin male Molex connector. • 6-pin male Molex connector with ground wire. PoE Data Hinge Hinge-side harness connectors: 4-pin M 4-pin F • 4-pin male molex connector • 6-pin male molex connector with ground wire Lock-side harness connectors: 6-pin M Frame 6-pin F Drain Wire • Ring terminal • (2) 4-pin connectors • 4-pin Molex connector • 4-pin connector PoE Hinge (Patent Pending) 1-800-810-WIRE • www.sargentlock.com • A7764B 01/29/11 Frame-Side Harness Assembly (15' length) Cable: CAT 5e or higher 24 AWG shielded, 100ohm 24AWG Stranded Wire for Earth Ground inside 15' Frame Harness Wire Profile Series v.S1 PoE Mortise Lock Door Harness Installation Ground Ring Terminal Order of installation may vary. Refer to appropriate sections for instructions. 1. Prop door open. 2. Tape the two lock-side 4-pin connectors to the ring terminal. 3. Using the ring terminal, carefully fish the assembly through the door channel to the lock. 4. Remove tape from ring terminal and door harness connectors. Hinge-side harness connectors: • 4-pin male Molex connector • 6-pin male Molex connector with ground wire Lock-side harness connectors: • Ring terminal • (2) 4-pin connectors: • 4-pin Molex connector • 4-pin connector JST 4-Pin From Hinge Connectors From Lock body Inside of Door PoE Lock 01/29/11 Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 4-pin F Drain Wire 6-pin M JST 4-Pin Cable: CAT 5e, 26 AWG stranded, shielded, 100ohm 4-Pin Molex Ground Ring Terminal Secured to Lock Mounting Plate 1-800-810-WIRE • www.sargentlock.com • A7764B Profile Series v.S1 PoE Mortise Lock PoE Lock Wiring Ground Ring Terminal (From Hinge to Top Left Escutcheon Screw) JP4 JP4 TP8 TP7 R22 R23 R21 TP7 TP8 C31 MTG2 R25 J6 23C MTG2 2ND 23C 4U 8R 51C 4R 51C 4R U1 5D 4U 5R 11R 5R 5D 2D 3C 3C MTG3 U2 6R11R L1 J7 U3 C4 7R TP1 TP2 TP6 J3 31D 2ND 1ND 73C 1ND J5 T1 41C 73C 1C 01C 8 1C 1C 8R 8 1C 01C C20 6R D4 D7 7R 11C D3 C2 C12 C16 R15 J4 5C R14 C19 TP4 DN3 TP3 31C R12 R9 D6 41C Q1 R2 R6 11C MTG3 C5 C11 C14 R4 5C C3 R7 R11 C12 D4 J3 C4 C4 J5 J5 T1 J7 TP6 U3 TP2 U2 J7 U3 C13 C19 TP1 L1 TP1 TP6 C20 TP2 D2 C12 D4 T1 C20 D7 J3 C15 C19 1U R12 R14 D3 C2 R2 R12 R14 D7 R15 C16 D5 MTG4 1U R3 D3 Q1 C2 TP4 DN3 TP3 R5 Q1 R2 MTG4 R15 C16 C6 R1 U4 C6 R3 C6 71C 61R 31R 01R 71C 61R 31R 01R D6 R9 D6 J7, J4 JST Connectors (From Hinge) C34 TP4 DN3 TP3 R3 D1 R8 D1 C35 C36 R1 R1R9 T2 D1 C18 C10 C17 R10 R13 R16 T2 C1 C37 T2 C35 MTG2 C34 MTG4 C35 C36 C34 C36 J6 DN1 J8 J2 MTG1 TP9 J6 DN2 MTG1 R24 J8 J2 C32 MTG1 C7 C8 TP5 J8 J2 C7 C8 D11 C33 TP5 R24 R25 C31 C9 D9 D9 R22 C7 C8 D9 D11 C33 TP9 JP3 TP5 D10 R22 C31 D11 TP7 TP8 R21C33 D10R24 TP9R23 R25 C9 C21 C9 R21 R23 JP4 JP3 JP3 D10 C21 C21 MTG3 J4 U2 L1 J4 D1 D9 R2 D1 C3 C2 R2 MTG4 Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. U2 TP C4 C1 2ND 1ND 73C 2ND 1ND 23C 1C 01C 73C 71C 31R 01R 61R 8 1C 1C 71C 31R 01R 081 8 1C 4U 61R MTG3 J4 8R J7 U3 5R TP TP L1 C1 D4 R1 6R L1 D4 (+) 9VDC (RED) (-) (BLACK) AX/DPS NC (PINK) AX/DPS COM (VIOLET) Unused Unused Unused EGND (GREEN) DX NC (GREEN/WHITE) RX COM (WHITE) RX NC (GREEN) DX (WHITE/BLACK) LX NO (RED/YELLOW) LX COM (RED/GREEN Motor B (BLACK) Motor A (RED) DPS DPS From Lock Body Ring Terminal From Trim Power 1-800-810-WIRE • www.sargentlock.com • A7764B 01/29/11 R1 J3 D3 U1 R3 D7 5D 4U Q1 C6 D6 C2 T2 2D J5 T1 5D J8 J2 3C DN R9 C1 R1 5R 11R 51C TP TP 4R D1 7R R1 C8 2D 31C MTG1 TP C7 4R R 115R1C C9 11C 31C 41C J6 23C MTG2 C3 C3 JP 3C TP C2 7R 25 5C C5 41C C11 C14 R6 11C TB2 TB1 C13 5C E1 J4 R7 U2 C4 R4 TP TP L1 C3 C1 MTG3 MTG3 R11 C15 D4 C1 J7 6 U TP J7 TP 2 U3 J3 J4 C4 D2 C1 1U C1 P6 0T C2 TP2 J3 D5 1U R1 R1 R2 R1 R1 D3 C2 Controller Board Connectors (Inside Escutcheon) T1 R5 Q1C2 R2 C2 U4 D3 MTG4 MTG4 Q1 D7 R8 T2 C6 3D7 TP D6 R1 R9 C1 D6 C18 T2 J5 T1J5 C1 D1 J2 R9 C10 MTG1 3 3 TP DN R1 4 TC1P6 C17 R10 R13 R16 D1 R1 DN C37 C8 C7 TP J8 J2 C8 C7 R3 TP R1 DN1 TP DN2 C3 C3 J6 MTG1 RC36 C32 J6 JP J8 MTG2 C3 C3 C3 C3 MTG2 C2 C9 C9 R2 C3 TP C3 TB1 E1 TB2 C3 C3 C3 R2 D9 D1 1 0 R2 R2 C2 R2 D1 TP8 R231 TJPP4R22 R2 D1 TP8 R213 C3 D925 TP R29 2 R1 D1 TPR21 R24 JP JP P4 TP TP8 01/29/11 Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Profile Series v.S1 PoE Mortise Lock Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS 10 16 12 11 13 1-800-810-WIRE • www.sargentlock.com • A7764B 15 14 15 Profile Series v.S1 PoE Mortise Lock Parts Breakdown 125 kHz Prox and 13.56 MHz iCLASS, continued ITEM PART NO. DESCRIPTION QTY. Outside Lever Reference 8200 Catalog for available levers Inside Lever Reference 8200 Catalog for available levers 82-0493 O/S Escutcheon only with Cylinder 82-0495 O/S Escutcheon only without Cylinder 82-0492 Inside Escutcheon only without Thumb Turn 82-4571 Inside Escutcheon only with Thumb Turn 52-2431 125 kHz Prox Only Bezel Assembly (PA) 52-2432 Keypad and 125kHz Prox Bezel Assembly (PK) OR 52-4420 13.56 MHz iCLASS Only Bezel Assembly (S1-IA) 13.56 MHz reader assembly ships configured for PoE/Hardpower use. 52-4421 Keypad and 13.56 MHz Bezel Assembly (S1-IK) 52-4424 S1 Controller Assembly (Double Pulse) 52-3855 Battery Cover Assembly 01-1212 Security Screw 52-2427 Profile Screw Pack - Specify Finish (Includes: Fire Stop Plate, Trim Mounting Screws, Security Allen Wrench) 10 Consult Factory Lever Handle Screw (Depends on Lever Style) 11 Consult Factory Inside Adapter Assembly (Depends on Lever Style) 12 Consult Factory Outside Adapter Assembly (Depends On Lever Style) 13 14 15 16 S1-82276-hand-finish Lockbody with Dead Bolt with Cylinder S1-82277-hand-finish Lockbody with Dead Bolt without Cylinder S1-82278-hand-finish Lockbody without Dead Bolt with Cylinder S1-82279-hand-finish Lockbody without Dead Bolt without Cylinder 82-0084 Faceplate with Dead Bolt (shown) 82-0081 Faceplate without Dead Bolt 77-4336 Mortise Screw Pack - Specify Finish (Includes: Wood and Metal Lock body Screws, Faceplate Screws, and Strike Screws) #43 Mortise Cylinder Consult Factory 1-800-810-WIRE • www.sargentlock.com • A7764B 01/29/11 Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 13.56 mHz reader assembly ships configured for PoE/Hardpower use. Profile Series v.S1 PoE Mortise Lock Lock Installation Step #1 – Door Preparation A. Verify Hand and Bevel of Door Stand on outside of locked door when determining door hand. LH LHRB RH RHRB Left Hand Hinges Left Open Inward Left Hand Reverse Bevel Hinges Left Open Outward Right Hand Hinges Right Open Inward Right Hand Reverse Bevel Hinges Right Open Outward Fig. 1A B. Door Preparation Prior to installation, all holes must be free of burrs, debris and sharp edges. 01/29/11 Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Prepare door according to appropriate template (see website www.intelligentopenings.com): • Manufacturer Door Template: 4533 Outside of Door Inside of Door Through-bolt Hole Through-bolt Hole *Raceway Ribbon Cable Hole (Controller to Keypad) Ribbon Cable Hole (Controller to Keypad) Inside of Lockbody Wire Hole (only with cylinder installation) Outside of Cylinder Hole (only with cylinder installation) Thumb Turn Lever Hole Lever Handle Hole Lever Handle Hole Mortised Pocket *Note: Raceway placement in document is approximate. 10 Pre-drilled and/or Tapped Holes Fig. 1B 1-800-810-WIRE • www.sargentlock.com • A7764B Profile Series v.S1 PoE Mortise Lock Step #2 – How to Change Hand of Lockbody A. Reverse Lock Hand Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A): 1. Position lock body with red surface of locking piece visible. 2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body. 3. Rotate the locking piece 180° until RED surface is on opposite side. Note: Red indicates locked side (outside). Wire harness MUST exit through the inside/non-cylinder side of the lockbody. B. Retaining Ring Slot Make sure the plastic retaining ring is seated correctly (Fig. 2B): 1. The wires and the plastic retaining ring must be located on the non-cylinder side. 2. Orient the plastic retaining ring so that the word Bottom is located at the bottom of the cylinder hole. Plastic Retaining Ring 3. Route the wires from the top of the cylinder hole into the slot on the top of the plastic retaining ring, NOT through the retaining ring. Fig. 2B Outside of Door Locking Guide Slot Push In Fig. 2A C. Reverse Latch Hand Beveled surface of latchbolt must face strike. The deadlatch is self adjusting. To change the hand of the latchbolt: 1. Insert the blade of a slotted screwdriver (>1/4”) into the spade shape slot behind latch. 2. Rotate the screwdriver 90° to push latchbolt out until back of bolt clears lock case front. 3. Rotate latchbolt 180° until the latchbolt drops back into the lockbody. Note: Latch cannot be unscrewed. Fig. 2C 1-800-810-WIRE • www.sargentlock.com • A7764B 11 01/29/11 Right Hand Shown Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Red Locking Piece Indicates Locked Side Profile Series v.S1 PoE Mortise Lock Ground Wire Step #3 – Install Lockbody 1. Feed the wires first through the mortise pocket and out the inside prep, followed by the lockbody (Fig. 3A). (2) 4-Pin Connectors From Hinge Note: Connectors and wires must be fed through non-cylinder side. 2. The wires from the lockbody exit the inside door prep through the mortise cutout. 3. Loosely secure the lockbody in the door with two #12 x 1-1/4” wood screws or #12-24 x 1/2” machine screws. Note: Do not completely tighten at this time. Mortise Connectors (2) #12-24 x 1/2” Long Flat Head Screws for Metal Doors Inside of Door Fig. 3A 01/29/11 Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. (2) #12 x 1-1/4” Long Flat Head Screws for Metal Doors Step #4 – Door Options (2) 1/8” Diameter Holes Required A. Fire Stop Plate (P/N 52-0033) Fire-rated doors require a fire stop plate on the outside of the door (Fig. 4A). Fire Stop Plate 1. Drill (2) 1/8" x 1-1/4" deep holes in the door if not already present. (2) #8 Self-Tapping Screws for Wood and Metal Doors Refer to template for fire-stop prep locations. 2. Attach with flap up and out using (2) #8 x 1/2” self-tapping screws for wood and metal doors. (2) Through-bolt Holes Fig. 4A Outside of Door B. Weather Conduit (52-2847) Install weather conduit on NON FIRE-RATED exterior doors only (Fig. 4B). 1. Carefully insert the weather conduit into the ribbon cable hole on the inside of the door. Ribbon Cable Hole O-Ring 2. Place the O-ring around the weather conduit on the outside and up against the door (Fig. 4C) Fig.4C Fig.4B 12 1-800-810-WIRE • www.sargentlock.com • A7764B Outside of Door Profile Series v.S1 PoE Mortise Lock Step #5 – Install Gasket (for Exterior Doors) Gasket 82-0500 1. Carefully remove the backing from the gasket. 2. Apply gasket to escutcheon: Gasket • Starting in one place, press the adhesive side of the gasket firmly against the escutcheon. • Work around the escutcheon, pressing the sticky side of the gasket firmly against the escutcheon edge. Keypad Ribbon Cable • The gasket should be aligned so that all edges of the escutcheon are covered. Fig. 5A 3. Attach escutcheon to the door after the wires are connected. Antenna (iCLASS) Only Note: The 43 cylinder may be used with or without a gasket. Ground Wire (E1) Step #6 – Install Outside Escutcheon and Lever Assembly 1A. For fire rated doors, feed ribbon cable with connector and ground wire from outside of door through weatherseal gasket and fire stop plate (Fig. 6A). Note: Install ribbon cable with cable exiting down 1B. For non-fire rated doors, feed ribbon cable with connector and ground wire from outside of door through weatherseal gasket (if used) and weather conduit (Fig. 6A). Fig. 5B Note: Install ribbon cable with cable exiting down With outside lever horizontal, locate the outside escutcheon on the door, while directing the mounting posts through the door and lock body (Fig. 6B). 3. On the inside of the door, insert spindle into square hole of mortise lock. 4. Slide inside adapter and plate assembly over spindle and loosely secure with 2 through bolt Ground screws (#8-32 x 5/8”). Note: For 8276 and 8278, loosely thread cylinder through escutcheon and into the lock body before tightening the lock case screws and escutcheon through bolts. Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Make sure the lever spindle is properly engaged in lock. Ring Terminal Ground Wire (E1) JST 4-Pin From Hinge Reader Cable Antenna (iCLASS) Ground Wire (E1) Antenna (iCLASS only) Keypad Ribbon Cable Mortise Lock body and AX Connectors Inside of Door Fig. 6A Fig. 6B Outside of Door 1-800-810-WIRE • www.sargentlock.com • A7764B 13 01/29/11 2. Profile Series v.S1 PoE Mortise Lock Step #7 – Escutcheon Wire Connections Images are shown without gasket. If gasket is necessary, refer to Step #5. Ground Ring Terminal Before the controller is attached to the door: 4-Pin Connectors From Hinge 1. Attach the reader assembly ribbon cable into the back of the controller assembly (side that faces towards the door when mounted (Fig. 7C Detail). 2. Attach the antenna to the circuit board in the plastic housing under the controller assembly. Antenna (iCLASS only) Ground Wire Ground Wire Note: The difference between the wiring for the iCLASS 13.56 MHz reader and the 125 kHz Prox is that the iCLASS wiring includes an antenna wire. 3. Attach the ground wire to the bottom of the controller assembly (E1, Fig. 7A). Reader Cable Outside Escutcheon Reader Cable Antenna (iCLASS) 01/29/11 Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Fig. 7A Step #8 – Additional Wiring Connections Lock, DPS and raceway wire connections: 1. Connect the cable from the mortise lock to the bottom of the controller assembly (TB1, Fig. 8A). 2. Connect the AX/DPS connector to the 2-pin harness. 3. Push the two connectors from the raceway over the controller assembly, through the gap between the plastic controller assembly and the escutcheon, Outside to the front of the Escutcheon circuit board. Ground Ring Terminal 4-Pin Connectors From Hinge Antenna (iCLASS only) Reader Cable TB1 Ground Wire Unused Mortise Connector AX/DPS Back Inside of Door Fig. 8A 14 1-800-810-WIRE • www.sargentlock.com • A7764B Profile Series v.S1 PoE Mortise Lock Step #9 – Ciruit Board Wiring Before installing escutcheon, route raceway cables and ground attach to front of circuit board. Turn the controller assembly over: Ground Ring Terminal 1. Route the raceway connectors over the top of the controller assembly and plug into the front of the circuit board (side that faces out when mounted (J7, J4; Fig. 9A). 2. Route the 2 ground ring terminals, one from the lock and the other from the hinge wiring, over the top of the controller assembly and connect both to the top escutcheon screw. Note: Connectors go on only one way. Do not offset connectors and make sure they are completely seated. Inside of Door Step #10 – Install Inside Escutcheon 1. Gently fold the excess ribbon connector and ground wire into the top hole, JST connectors and ground wire into offset middle hole, and mortise and AX/DPS wires into bottom hole, being careful not to pinch wires (Fig. 10A). 2. Insert (2) #8-32 x 1-1/4" screws through inside escutcheon and thread into outside escutcheon (Fig. 10B) Straighten escutcheons and tighten securely. Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Fig. 9A Inside of Door Fig. 10B 1-800-810-WIRE • www.sargentlock.com • A7764B 15 01/29/11 Fig. 10A Profile Series v.S1 PoE Mortise Lock Step #11 – Install Inside Lever 1. Slide lever handle onto spindle until fully seated (Fig. 11A). 2. Tighten the set screw securely with 1/8” hex wrench. Spindle Step #12 – Install and Secure Cylinder Set Screw 1. Slide cylinder through the spring and rosette/collar and screw into lockbody, rotating the cylinder clockwise (Fig. 12A). Cylinder should be flush with rosette/collar. Fig. 11A Note: SARGENT logo must be horizontal and on the top of the cylinder (Fig. 12B). Inside of Door 2. Secure the cylinder by tightening cylinder clamp screw located above the deadbolt using #2 Phillips screwdriver (Fig. 12C). Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 01/29/11 Inside Lever 3. Using the key, test cylinder functions: • 8278 Function: Key retracts latch-. • 8276 Function: Key retracts latch and projects and retracts deadbolt-. Position cylinder so that the SARGENT logo is right-side up. Correct Incorrect Type 43 Cylinder Fig. 12B Cylinder Clamp Screw Key Fig. 12A #2 Phillips Screwdriver Outside of Door Fig. 12C 16 1-800-810-WIRE • www.sargentlock.com • A7764B Profile Series v.S1 PoE Mortise Lock Step #13 – Attach Front Plate Attach front plate with (2) flat head screws. Outside of Door Front Plate (2) Flat Head Screws Lock body Screws Fig. 13A Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Operational Check 1A. For 8276- and 8278- function mortise locks with cylinders: • Insert key into cylinder and rotate. There should be no friction against lock case, wire harness or any other obstructions. • Refer to Section 6, Step 8 Wiring if harness friction exists). Check that the key retracts the latch: The key should rotate freely. 1B. For 8276- and 8277- function: • Throw the deadbolt: Check that the key retracts both the deadbolt and the latch. • Try the inside lever: Ensure it retracts latch and deadbolt (if provided). 2. Use a prox 125 kHz or 13.56 MHz iCLASS credential, or keypad PIN code set up with the Network and Lock Configuration Tool to unlock outside lever and retract latch. Refer to Network Lock and Configuration Tool user manual (WFMN1D) for information on how to configure and program v.S1 locks. 1-800-810-WIRE • www.sargentlock.com • A7764B 17 01/29/11 SARGENT Manufacturing 100 Sargent Drive New Haven, CT 06511 USA 800-810-WIRE (9473) • www.sargentlock.com Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications. The company’s customer base includes commercial construction, institutional, and industrial markets. Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience. A7764B-01/11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Kirby.Munroe Create Date : 2011:02:24 20:56:43-05:00 Modify Date : 2011:02:24 20:56:43-05:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2011:02:24 20:56:43-05:00 Creator Tool : Adobe Acrobat 9.1.1 Format : application/pdf Title : Microsoft Word - XX-XXXX - Exhibit Cover Creator : Kirby.Munroe Document ID : uuid:8361f42c-ce5f-4381-8b65-91272e45ecfe Instance ID : uuid:a03e6e83-3fd0-4e2a-b042-143bfc3d825a Producer : Adobe Acrobat 9.1.1 Page Count : 19EXIF Metadata provided by EXIF.tools