Deere and ISG Electronic Systems JDGT-0001 Skylinks Head Unit and Skylinks Power Supply User Manual Installation Manual Part two

Phoenix International Corporation Skylinks Head Unit and Skylinks Power Supply Installation Manual Part two

Instruction Manual Part 2

Installation InstructionsOverview of Generic UHF Antenna Bracket InstallationFCC Antenna WarningUse of any antenna other than the one provided with this kit may expose the user or nearby personsto radio frequency (RF) emission levels outside the FCC safety guidelines.§ Left (drivers side) and Right side of cart will be identified as someone sitting forward incart.§ Before doing any work on golf cart, make sure that the key is in the off position.§ Ensure the parking brake is set.§ Remove windshields if installed before beginning as per Cart Manufacture User’sManual.§ The UHF antenna cable is not attached to the Display Unit during this phase of theinstallation. Leave cable assemble available for easy access for latter in the installation.Specific UHF Antenna Bracket Installation instructions per cart type (ex. Club Car, EZ-GO,Yamaha), and model.Club Car Pre 2000 UHF Antenna Bracket Installation Parts1. Bracket / Antenna2. Antenna whip3. Phillips Screws (2)4. Flat Washer (2)5. Spacer (2) Club Car Completed Pre 2000 UHF Bracket Installation12345
Future picture of completed UHF Bracket Installation. Club Car UHF Pre 2000 Bracket Installation1. Remove right side of cart bracket on hood of cart.2 7/16 bolts with locking nut.
3. Attach Antenna whip upon completion of UHF antenna Bracket.1. Mount UHF antenna onright side of cart using thetwo Phillips head screws,flat washer and sheathingpieces.Important: UHF bracketneeds to be isolated from cart ground.FCC Antenna Warning LabelWhile the device is in operation, aseparation of at least 500 mm (20 in.)must be maintained betweenantennae and the body of the user ornearby persons in order to meet theFCC RF exposure guidelines.Future picture of Antenna whip beinginstalled.
4. Route UHF antenna cable down roof support. Placing the first tie strap at the top bend of support, and another every 6-8 inches.Important: Do not pull UHFcable tight at the rooflocation. Allow a gentle bendto cart frame. = Zip tie location5. This completes the UHFbracket and UHF cableinstallation.Note: Leave UHF cableconnector end unattached. Itwill be connected latter in theinstallation.Club Car Post 2000 UHF Antenna Bracket Installation Parts
1. Antenna2. Antenna whip3. Bracket4. Spacer5. Phillips Screws (2)6. Flat Washer (2)Club Car Post 2000 Completed UHF Bracket InstallationFuture picture of completed UHF Bracket Installation.A future picture of the UHF antenna, antenna whip,bracket, Phillips screws, and flat washer will beinserted.
Club Car UHF Post 2000 Bracket Installation1. Remove left side 7/16bolts securing roof .
2. Attach screw,washer and plasticsheathing to bracket,and secureImportant:UHF bracketneeds to beisolated from cart ground.
3. Attach Antenna bracket withscrews and lock tight.
5. Attach Antenna cable tobracket, and attach whip.FCC Antenna Warning LabelWhile the device is in operation, aseparation of at least 500 mm (20in.) must be maintained betweenantennae and the body of the useror nearby persons in order to meetthe FCC RF exposure guidelines. 4. Route UHF antenna cabledown roof support. Placing thefirst tie strap at the top bend ofsupport, and another every 6-8inches.Important: Do not pull UHFcable tight at the rooflocation. Allow a gentle bendto cart frame. = Zip tie location5. This completes the UHFbracket and UHF cableinstallation.Note: Leave UHF cableconnector end unattached. Itwill be connected latter in theinstallation.
EZ-GO UHF Antenna Bracket Installation Parts1. Antenna2. Antenna whip3. Bracket4. To Be Determined5. To Be Determined6. To Be DeterminedEZ-GO Completed UHF Antenna Bracket InstallationA future picture of the UHF antenna, antenna whip,bracket, Phillips screws, and flat washer will beinserted.
Future picture of completed EZ-GO UHF Bracket Installation.EZ-GO UHF Bracket Installation1. Remove right side of cartbracket on hood of cart.Important: UHF bracket needs to be isolated from cart ground.
2. Mounting process to bedetermined.Future Picture of how bracket should look being mountedwith appropriate screws.Future tools required to remove bracketFuture picture of bracketFuture picture of bracket
2. Attach Antenna whipupon completion ofUHF antenna Bracket.FCC Antenna Warning LabelWhile the device is in operation, aseparation of at least 500 mm (20in.) must be maintained betweenantennae and the body of the useror nearby persons in order to meetthe FCC RF exposure guidelines.Future picture of Antenna whip beinginstalled.
4. Route UHF antenna cabledown roof support. Placingthe first tie strap at the topbend of support, and anotherevery 6-8 inches.Important: Do not pullUHF cable tight at the rooflocation. Allow a gentlebend to cart frame. = Zip tie location5. This completes the UHFbracket and UHF cableinstallation.Note: Leave UHF cableconnector end unattached.It will be connected latter inthe installation.Yamaha UHF Antenna Bracket Installation PartsFuture picture of bracket with bend of UHF antenna.Future picture of cart with tie strap locations.
1. Antenna2. Antenna whip3. Bracket4. To Be Determined5. To Be Determined6. To Be Determined Yamaha Completed UHF Antenna Bracket InstallationA future picture of the UHF antenna, antenna whip,bracket, Phillips screws, and flat washer will beinserted.
Future picture of completed Yamaha UHF Bracket Installation.
Yamaha UHF Bracket Installation1. Remove right side of cartbracket on hood of cart.Important: UHF bracket needs to be isolated from cart ground.Future picture of bracketFuture picture of bracketFuture picture of bracket with toolsrequired
3. Attach Antenna whip uponcompletion of UHF antennaBracket.4. Route UHF antenna cable2. Mounting process to bedetermined.FCC Antenna Warning LabelWhile the device is in operation, aseparation of at least 500 mm (20in.) must be maintained betweenantennae and the body of the user ornearby persons in order to meet theFCC RF exposure guidelines.Future picture of Antenna whip beinginstalled.Future Picture of how bracket should look being mountedwith appropriate screws.
down roof support. Placing thefirst tie strap at the top bend ofsupport, and another every 6-8inches.Important: Do not pull UHFcable tight at the rooflocation. Allow a gentle bendto cart frame. = Zip tie location5. This completes the UHFbracket and UHF cableinstallation.Note: Leave UHF cableconnector end unattached. Itwill be connected latter in theinstallation.Future picture of bracket with bend of UHF antenna.Future picture of cart with tie strap locations.
Overview of Generic GPS Antenna Bracket Installation§ Left (drivers side) and Right side of cart will be identified as someone sitting forward incart.§ Before doing any work to the golf cart, make sure the key is in the off position.§ Ensure the parking brake is set.§ Remove windshields if installed before beginning installation as per Cart ManufactureUser’s Manual.§ The GPS antenna cable is not attached to the Display Unit during this phase of theinstallation. Leave cable assemble available for easy access for latter in the installation.Specific GPS Antenna Bracket Installation instructions per cart type ex. (Club Car, EZ-GO,Yamaha) and Model type.Club Car Pre 2000 GPS Antenna Bracket Installation Parts1. GPS Antenna andbracket2. Spacer3. Phillips Screws (2)4. Flat Washer (2) Club Car Completed Pre 2000 GPS Bracket Installation
Future picture of completed GPS Bracket Installation.
Club Car Pre 2000 GPS Bracket Installation1. Remove Left side of cart bracket on hood of cart.2 7/16 bolts with locking nut.
2. Mount GPS antenna on Left side of cart using the two Phillips head screws, flat washer and sheathing pieces. Important: GPS bracket needs to be isolated from cart ground.Future Picture of GPS antenna being mounted.
3. Route GPS antenna cable down roof support. Placing the first tie strap at the top bend of support, and another every 6-8 inches.Important: Do not pullGPS cable tight at the rooflocation. Allow a gentlebend to cart frame. = Zip tie location4. This completes the GPSbracket and GPS cableinstallation.Note: Leave GPS cableconnector end unattached.It will be connected latter inthe installation.Future picture of GPS Antenna with bend to roof.
Club Car Post 2000 GPS Antenna Bracket Installation Parts1. Antenna2. Bracket3. Spacer4. Phillips Screws (2)5. Flat Washer (2)Club Car Completed Post 2000 GPS Bracket InstallationA future picture of the GPS antenna, antenna whip,bracket, Phillips screws, and flat washer will beinserted.
Future picture of completed GPS Bracket Installation.
Club Car Post 2000 GPS Bracket Installation1. Remove Left side of cartbracket on hood of cart.2 7/16 bolts with locking nut.
2. Mount GPS antenna on Leftside of cart using the twoPhillips head screws, flat washerand sheathing pieces. Important: GPS bracket needs to be isolated from cart ground.Future Picture of GPS antenna being mounted.
3. Route GPS antenna cabledown roof support. Placingthe first tie strap at the topbend of support, and anotherevery 6-8 inches.Important: Do not pullGPS cable tight at the rooflocation. Allow a gentlebend to cart frame. = Zip tie location4. This completes the GPSbracket and GPS cableinstallation.Note: Leave GPS cableconnector end unattached.It will be connected latter inthe installation.Future picture of GPS Antenna with bend to roof.
EZ-GO GPS Antenna Bracket Installation Parts1. Antenna2. Bracket3. To Be Determined4. To Be Determined5. To Be DeterminedEZ-GO Completed GPS Antenna Bracket InstallationA future picture of the GPS antenna, bracket, andother parts to be determined will be inserted.
Future picture of completed EZ-GO GPS Bracket Installation.EZ-GO GPS Bracket Installation1. Remove Left side of cartbracket on hood of cart.Future picture of bracketFuture picture of bracketFuture picture of bracket with toolsrequired
2. Mounting process to bedetermined.Important: GPS bracket needs to be isolated from cart ground.Future Picture of how bracket should look being mountedwith appropriate screws.
3. Route GPS antenna cabledown roof support. Placingthe first tie strap at the topbend of support, and anotherevery 6-8 inches.Important: Do not pullUHF cable tight at the rooflocation. Allow a gentlebend to cart frame. = Zip tie location5. This completes the GPSbracket and GPS Antennainstallation.Note: Leave GPS cableconnector end unattached.It will be connected latter inthe installation.Future picture of bracket with bend of GPS antenna.Future picture of cart with tie strap locations.
Yamaha GPS Antenna Bracket Installation Parts1. Antenna2. Bracket3. To Be Determined4. To Be Determined5. To Be Determined Yamaha Completed GPS Antenna Bracket InstallationA future picture of the GPS antenna, bracket, andother parts to be determined will be inserted.
Future picture of completed Yamaha GPS Bracket Installation.Yamaha GPS Bracket Installation1. Remove Left side of cartbracket on hood of cart.Important: GPS bracket needs to be isolated from cart ground.
3. Route GPS antenna cabledown roof support. Placing2. Mounting process to bedetermined.Future picture of bracketFuture picture of bracketFuture picture of bracket with toolsrequiredFuture Picture of how bracket should look being mountedwith appropriate screws.
the first tie strap at the topbend of support, and anotherevery 6-8 inches.Important: Do not pullUHF cable tight at the rooflocation. Allow a gentlebend to cart frame. = Zip tie location4. This completes the GPSbracket and GPS cableinstallation.Note: Leave GPS cableconnector end unattached.It will be connected latter inthe installation.Future picture of bracket with bend of UHF antenna.Future picture of cart with tie strap locations.
Overview of Generic Power Harness Installation• Make sure key switch is in the off position.Use caution when working around the batteries. Battery acid may exist around the terminal area.

Navigation menu