Deere and ISG Electronic Systems JDGT-0001 Skylinks Head Unit and Skylinks Power Supply User Manual Installation Manual Part two

Download:
Mirror Download [FCC.gov]
Document ID	118569
Application ID	24FsHEyOOzn9rs4A2wVf4A==
Document Description	Instruction Manual Part 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.52kB (431470 bits)
Date Submitted	2000-09-25 00:00:00
Date Available	2001-03-05 00:00:00
Creation Date	2000-08-30 17:04:16
Producing Software	Acrobat PDFWriter 4.0 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	Installation Manual Part two
Document Creator	Microsoft Word - Installation Manual Part two.doc

Installation Instructions
Overview of Generic UHF Antenna Bracket Installation
FCC Antenna Warning
Use of any antenna other than the one provided with this kit may expose the user or nearby persons
to radio frequency (RF) emission levels outside the FCC safety guidelines.
§
Left (drivers side) and Right side of cart will be identified as someone sitting forward in
cart.
Before doing any work on golf cart, make sure that the key is in the off position.
Ensure the parking brake is set.
Remove windshields if installed before beginning as per Cart Manufacture User’s
Manual.
The UHF antenna cable is not attached to the Display Unit during this phase of the
installation. Leave cable assemble available for easy access for latter in the installation.
§
§
§
§
Specific UHF Antenna Bracket Installation instructions per cart type (ex. Club Car, EZ-GO,
Yamaha), and model.
Club Car Pre 2000 UHF Antenna Bracket Installation Parts
1.
2.
3.
4.
5.
Bracket
/ Antenna
Antenna whip
Phillips Screws (2)
Flat Washer (2)
Spacer (2)
Club Car Completed Pre 2000 UHF Bracket Installation
Future picture of completed UHF Bracket Installation.
Club Car UHF Pre 2000 Bracket Installation
1. Remove right side of cart
bracket on hood of cart.
2 7/16 bolts with locking nut.
1. Mount UHF antenna on
right side of cart using the
two Phillips head screws,
flat washer and sheathing
pieces.
Important: UHF bracket
needs to be isolated from
cart ground.
FCC Antenna Warning Label
While the device is in operation, a
separation of at least 500 mm (20 in.)
must be maintained between
antennae and the body of the user or
nearby persons in order to meet the
FCC RF exposure guidelines.
Future picture of Antenna whip being
installed.
3. Attach Antenna whip upon
completion of UHF antenna
Bracket.
4. Route UHF antenna cable
down roof support. Placing
the first tie strap at the top
bend of support, and
another every 6-8 inches.
Important: Do not pull UHF
cable tight at the roof
location. Allow a gentle bend
to cart frame.
= Zip tie location
5. This completes the UHF
bracket and UHF cable
installation.
Note: Leave UHF cable
connector end unattached. It
will be connected latter in the
installation.
Club Car Post 2000 UHF Antenna Bracket Installation Parts
A future picture of the UHF antenna, antenna whip,
bracket, Phillips screws, and flat washer will be
inserted.
1.
2.
3.
4.
5.
6.
Antenna
Antenna whip
Bracket
Spacer
Phillips Screws (2)
Flat Washer (2)
Club Car Post 2000 Completed UHF Bracket Installation
Future picture of completed UHF Bracket Installation.
Club Car UHF Post 2000 Bracket Installation
1. Remove left side 7/16
bolts securing roof
2. Attach screw,
washer and plastic
sheathing to bracket,
and secure
Important:
UHF bracket
needs to be
isolated from
cart ground.
3. Attach Antenna bracket with
screws and lock tight.
5. Attach Antenna cable to
bracket, and attach whip.
FCC Antenna Warning Label
While the device is in operation, a
separation of at least 500 mm (20
in.) must be maintained between
antennae and the body of the user
or nearby persons in order to meet
the FCC RF exposure guidelines.
4. Route UHF antenna cable
down roof support. Placing the
first tie strap at the top bend of
support, and another every 6-8
inches.
Important: Do not pull UHF
cable tight at the roof
location. Allow a gentle bend
to cart frame.
= Zip tie location
5. This completes the UHF
bracket and UHF cable
installation.
Note: Leave UHF cable
connector end unattached. It
will be connected latter in the
installation.
EZ-GO UHF Antenna Bracket Installation Parts
A future picture of the UHF antenna, antenna whip,
bracket, Phillips screws, and flat washer will be
inserted.
1.
2.
3.
4.
5.
6.
Antenna
Antenna whip
Bracket
To Be Determined
To Be Determined
To Be Determined
EZ-GO Completed UHF Antenna Bracket Installation
Future picture of completed EZ-GO UHF Bracket Installation.
EZ-GO UHF Bracket Installation
1. Remove right side of cart
bracket on hood of cart.
Important: UHF bracket
needs to be isolated
from cart ground.
Future
of
tools required
to remove bracket
Future picture
picture
of bracket
bracket
Future Picture of how bracket should look being mounted
2. Mounting process to be
with appropriate screws.
determined.
Future picture of Antenna whip being
installed.
2. Attach Antenna whip
upon completion of
UHF antenna Bracket.
FCC Antenna Warning Label
While the device is in operation, a
separation of at least 500 mm (20
in.) must be maintained between
antennae and the body of the user
or nearby persons in order to meet
the FCC RF exposure guidelines.
Future picture of bracket with bend of UHF antenna.
Future picture of cart with tie strap locations.
4. Route UHF antenna cable
down roof support. Placing
the first tie strap at the top
bend of support, and another
every 6-8 inches.
Important: Do not pull
UHF cable tight at the roof
location. Allow a gentle
bend to cart frame.
= Zip tie location
5. This completes the UHF
bracket and UHF cable
installation.
Note: Leave UHF cable
connector end unattached.
It will be connected latter in
the installation.
Yamaha UHF Antenna Bracket Installation Parts
A future picture of the UHF antenna, antenna whip,
bracket, Phillips screws, and flat washer will be
inserted.
1.
2.
3.
4.
5.
6.
Antenna
Antenna whip
Bracket
To Be Determined
To Be Determined
To Be Determined
Yamaha Completed UHF Antenna Bracket Installation
Future picture of completed Yamaha UHF Bracket Installation.
Yamaha UHF Bracket Installation
Future
Future picture
picture of
of bracket
bracket
Future picture of bracket with tools
required
1. Remove right side of cart
bracket on hood of cart.
Important: UHF bracket
needs to be isolated
from cart ground.
Future picture of Antenna whip being
installed.
Future Picture of how bracket should look being mounted
2. Mounting process to be
with appropriate screws.
determined.
FCC Antenna Warning Label
While the device is in operation, a
separation of at least 500 mm (20
in.) must be maintained between
antennae and the body of the user or
nearby persons in order to meet the
FCC RF exposure guidelines.
3. Attach Antenna whip upon
completion of UHF antenna
Bracket.
4. Route UHF antenna cable
Future picture
picture of
of bracket
cart withwith
tie strap
Future
bend locations.
of UHF antenna.
down roof support. Placing the
first tie strap at the top bend of
support, and another every 6-8
inches.
Important: Do not pull UHF
cable tight at the roof
location. Allow a gentle bend
to cart frame.
= Zip tie location
5. This completes the UHF
bracket and UHF cable
installation.
Note: Leave UHF cable
connector end unattached. It
will be connected latter in the
installation.
Overview of Generic GPS Antenna Bracket Installation
§
Left (drivers side) and Right side of cart will be identified as someone sitting forward in
cart.
Before doing any work to the golf cart, make sure the key is in the off position.
Ensure the parking brake is set.
Remove windshields if installed before beginning installation as per Cart Manufacture
User’s Manual.
The GPS antenna cable is not attached to the Display Unit during this phase of the
installation. Leave cable assemble available for easy access for latter in the installation.
§
§
§
§
Specific GPS Antenna Bracket Installation instructions per cart type ex. (Club Car, EZ-GO,
Yamaha) and Model type.
Club Car Pre 2000 GPS Antenna Bracket Installation Parts
1.
2.
3.
4.
GPS Antenna and
bracket
Spacer
Phillips Screws (2)
Flat Washer (2)
Club Car Completed Pre 2000 GPS Bracket Installation
Future picture of completed GPS Bracket Installation.
Club Car Pre 2000 GPS Bracket Installation
1. Remove Left side of cart
bracket on hood of cart.
2 7/16 bolts with locking nut.
Future Picture of GPS antenna being mounted.
2. Mount GPS antenna on Left
side of cart using the two
Phillips head screws, flat
washer and sheathing
pieces.
Important: GPS bracket
needs to be isolated
from cart ground.
Future picture of GPS Antenna with bend to roof.
3. Route GPS antenna cable
down roof support. Placing
the first tie strap at the top
bend of support, and
another every 6-8 inches.
Important: Do not pull
GPS cable tight at the roof
location. Allow a gentle
bend to cart frame.
= Zip tie location
4. This completes the GPS
bracket and GPS cable
installation.
Note: Leave GPS cable
connector end unattached.
It will be connected latter in
the installation.
Club Car Post 2000 GPS Antenna Bracket Installation Parts
A future picture of the GPS antenna, antenna whip,
bracket, Phillips screws, and flat washer will be
inserted.
1.
2.
3.
4.
5.
Antenna
Bracket
Spacer
Phillips Screws (2)
Flat Washer (2)
Club Car Completed Post 2000 GPS Bracket Installation
Future picture of completed GPS Bracket Installation.
Club Car Post 2000 GPS Bracket Installation
1. Remove Left side of cart
bracket on hood of cart.
2 7/16 bolts with locking nut.
Future Picture of GPS antenna being mounted.
2. Mount GPS antenna on Left
side of cart using the two
Phillips head screws, flat washer
and sheathing pieces.
Important: GPS bracket
needs to be isolated
from cart ground.
Future picture of GPS Antenna with bend to roof.
3. Route GPS antenna cable
down roof support. Placing
the first tie strap at the top
bend of support, and another
every 6-8 inches.
Important: Do not pull
GPS cable tight at the roof
location. Allow a gentle
bend to cart frame.
= Zip tie location
4. This completes the GPS
bracket and GPS cable
installation.
Note: Leave GPS cable
connector end unattached.
It will be connected latter in
the installation.
A future picture of the GPS antenna, bracket, and
other parts to be determined will be inserted.
EZ-GO GPS Antenna Bracket Installation Parts
1.
2.
3.
4.
5.
Antenna
Bracket
To Be Determined
To Be Determined
To Be Determined
EZ-GO Completed GPS Antenna Bracket Installation
Future picture of completed EZ-GO GPS Bracket Installation.
EZ-GO GPS Bracket Installation
Future
Future picture
picture of
of bracket
bracket
1. Remove
FutureLeft
picture
sideofofbracket
cart with tools
bracketrequired
on hood of cart.
Picture of how bracket should look being mounted
2. Future
Mounting
process to be
with appropriate screws.
determined.
Important: GPS bracket
needs to be isolated
from cart ground.
Future
withwith
tie strap
Future picture
picture of
of cart
bracket
bendlocations.
of GPS antenna.
3. Route GPS antenna cable
down roof support. Placing
the first tie strap at the top
bend of support, and another
every 6-8 inches.
Important: Do not pull
UHF cable tight at the roof
location. Allow a gentle
bend to cart frame.
= Zip tie location
5. This completes the GPS
bracket and GPS Antenna
installation.
Note: Leave GPS cable
connector end unattached.
It will be connected latter in
the installation.
Yamaha GPS Antenna Bracket Installation Parts
A future picture of the GPS antenna, bracket, and
other parts to be determined will be inserted.
1.
2.
3.
4.
5.
Antenna
Bracket
To Be Determined
To Be Determined
To Be Determined
Yamaha Completed GPS Antenna Bracket Installation
Future picture of completed Yamaha GPS Bracket Installation.
Yamaha GPS Bracket Installation
1. Remove Left side of cart
bracket on hood of cart.
Important: GPS bracket
needs to be isolated
from cart ground.
Future
Future picture
picture of
of bracket
bracket
Future picture of bracket with tools
required
Future Picture of how bracket should look being mounted
2. Mounting process to be
with appropriate screws.
determined.
3. Route GPS antenna cable
down roof support. Placing
Future picture
picture of
of bracket
cart withwith
tie strap
Future
bend locations.
of UHF antenna.
the first tie strap at the top
bend of support, and another
every 6-8 inches.
Important: Do not pull
UHF cable tight at the roof
location. Allow a gentle
bend to cart frame.
= Zip tie location
4. This completes the GPS
bracket and GPS cable
installation.
Note: Leave GPS cable
connector end unattached.
It will be connected latter in
the installation.
Overview of Generic Power Harness Installation
• Make sure key switch is in the off position.
Use caution when working around the batteries. Battery acid may exist around the terminal area.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 38
Creator                         : Microsoft Word - Installation Manual Part two.doc
Create Date                     : 2000:08:30 17:04:16
Title                           : Installation Manual Part two
Producer                        : Acrobat PDFWriter 4.0 for Windows

EXIF Metadata provided by EXIF.tools