Electronic Systems Technology ESTEEM192S Wireless Modem User Manual appendix c

Electronic Systems Technology Wireless Modem appendix c

user manual appendix c

APPENDIX CSPECIFCATIONSESTeem Command Error Message TableRevised: 11 Feb 99 APX C-1 Listed below are the ESTeem Command Error Messages and their definitions. To receive these messages, TYPSYSTEM mustbe ON (See Appendix D, Definitions). All System Status Message have a bell (O7H or CTRL G) preceding the message exceptwhen Messform is ON. If MESSFORM = OFF Line A will be displayed. If MESSFORM = ON Line B will be displayed. 1. A "TOO MANY CHARACTERS FOR COMMAND" BEMO1This message will be displayed if more than the allocatednumber of characters are typed for a command. This isbecause some commands are truncated at a length of 8characters. 2. A "AMBIGUOUS COMMAND"BEMO2This is the case of not enough characters being entered touniquely identify a command.3. A "INVALID ARGUMENT"BEM03This is displayed when a non valid value is given to aCommand. Example; a value of O cannot be given toFRACK because the only valid values are 1-255.
APPENDIX CSPECIFCATIONSESTeem System Status Message TableRevised: 11 Feb 99 APX C-2 Listed below are the ESTeem System Status Messages and their definitions. To receive these messages, TYPSYSTEM must beON (See APPENDIX D, DEFINITIONS). All System Status Messages have a bell (O7H or CTRL G) preceding the messageexcept when Messform is ON. If Messform = OFF Line A will be displayed. If Messform = ON Line B will be displayed. 1. A "CONNECTED TO XX"B SSO1-xxThis message is caused by either receiving a reply froma Log On Packet, receiving a Log On Packet, or bytyping LINK when connected and in the COMMANDMODE. XX is the address of the modem connected to. 2. A "DISCONNECTED FROM XX"B SSO2-xxTells that you have been disconnected from the deviceyou were originally connected to (xx is unit address). 3. A "LINK DOWN"B SSO3This message occurs after sending the last retry datapacket and receiving no response from the destinationnode. This message usually indicates a hard failure-i.e. destination node not energized, wrong baud rate,(not compatible between units) impropertransmit/receive frequency between nodes, etc. 4. A "CURRENTLY NOT CONNECTED!"B SSO4The Disconnect was issued while the modem was notconnected to another modem or when LINK is typed inthe COMMAND MODE when you are not connected.This message is displayed when the modem is configured inthe monitor mode.5. A "FAILED TO CONNECT!"B SS05This message occurs if the modem fails to connect.6. A "FAILED TO DISCONNECT!" B SS06This message occurs if the modems are connected andare unable to disconnect.7. A "USING FACTORY DEFAULTS"B SS07This command states when factory defaults have beenenabled.8. A "REMOTE PROGRAMMING"B SS08This message is displayed when the ESTeem has beenplaced in the remote programming mode.9. A "PHONE MODEM CONNECTED. INFRARED PORT DISABLED"B SS09This message is displayed when the ESTeem phoneport has received an in-coming call.10. A "PHONE MODEM DISCONNECTED. INFRARED PORT ENABLED"B SS10This message is displayed when the ESTeem port hasbeen disconnected.
APPENDIX CSPECIFCATIONSESTeem System Error Message TableRevised: 11 Feb 99 APX C-3 Listed below are the ESTeem System Error Messages and their definitions. To receive these messages, TYPSYSTEM must beON (See APPENDIX D, DEFINITIONS). All System Status Messages have a bell (O7H or CTRL G) preceding the messageexcept when Messform is ON. If Messform = OFF Line A will be displayed. If Messform = ON Line B will be displayed.1. A "NOVRAM FAILED"B SEO1If this response is received after a save, there is ahardware problem with the ESTeem's NOVRAMCircuitry.2. A "ROM FAILED"B SEO2If this response is received after a save, there is ahardware problem with the ESTeem's ROM Circuitry.3. A “BASE BAND FAILED”B SEO3This indicates that the Base Band Processor is notoperating correctly.

Navigation menu