Gantner Electronic GEA1150002A Access Control Terminal, Access Control Terminal with Biometry User Manual Brochure 6100F

Gantner Electronic GmbH Access Control Terminal, Access Control Terminal with Biometry Brochure 6100F

Contents

Brochure 6100F

Function descriptionThe GAT Access 6100 F reads contact-free data carriers and checks and grants authorisations. The user holds the data carrier over the round scan field and selects the required service via the acknowledge key. The integrated 4-segment LED display, monochrome LCD display and acoustic signal indicate authorisation.Via the fingerprint reader GAT FR 055 the identification of the visitors is verified by comparing their fingerprints with the fingerprint templates (two templates per visitor) stored on the visitor‘s personal data carriers. The combination of RFID data carriers and fingerprints allows for optimal protection against misuse of data carriers.For capturing the fingerprints and storing them to the data carriers the GAT Access 6100 F Enrollment Station is used.Highlights• Activation of turnstiles, doors etc. via relay output• Feedback input• User guidance via monochrome display (LCD), 4-segment LED display, illuminated round scan field and beeper• Secure data transmission between reader and data carrier• Read/write frequency 13.56 MHz• Reading MIFARETM Standard data carriers• Expandabilities for verification via fingerprint• Opening of housing only possible with special tool• Plug & Play installationGAT Access 6100 FAccess Control Terminal with BiometryApplicationThe GAT Access 6100 F with fingerprint reader GAT FR 055 is a stylish terminal for access control in leisure facilities such as swimming pools, spas and gyms. Identification at the terminal is by contact-free RFID data carrier (Radio Frequency Identification).With the fingerprint reader GAT FR 055 access control is extended by verification with biometric data, which enables optimal protection against misuse of personal data carriers.Information for user guidance is displayed via a graphical monochrome display (LCD).Description PartNo.GAT Access 6100 FTerminal for entry control with integrated, contactless MIFARETM reader, with black-white display (LCD)776487GAT FR 055Fingerprint reader for GAT Access 6100 F, wall mounting557433GAT FR 055 Weather CoverWeather protection cover for GAT FR 055 andGAT FR 055 FIU 3k1745291www.gantner.comOrder informationDescription PartNo.GAT Access 6100 F Enrollment StationTable station for capturing fingerprints174327GAT Reader WKTool to open the reader housing581683AccessoriesValid as from July 31th 2013 • Technical data subject to modifications without notice! DB_GAT-ACCESS6100F--BIO-EN_11.indd • PartNo.: 243526GAT Access 6100 FFingerprint readerGAT FR 055
Nominal voltage: 12/24 VDC (SELV - safety extra-low voltage)Permitted input voltage: 10 to 28 VDCAver. power consumption: - Full operation sensor in: 4.5 W- Full operation sensor out: 3.5 WData storage: Internal EEPROM memory for configuration and booking memory, data preservation min. 10 yearsInternal clock: Data preservation approx. 12 h(Gold-Cap)Reader type: MIFARETM StandardFrequency reading field: 13.56 MHzGAT FR 055 sensor: - Scanner type: optical sensor, 500 dpi @ 8-bit per pixel, active area: 13 x 20 mm- Verification time: < 0.8 sec.- Identification time: < 1 sec.- False acceptance rate 0.01% (recommended), adjustable over wide rangeDisplay elements: - Full graphical monochrome display (LCD) with white LED background lighting, resolution 128 x 64 pixels, visible area 50 x 25 mm- RFID reader (illuminated)- Acoustic signal- 4-segment LED display with different coloursControl elements: - 4 function keys- RFID readerHost interface: Ethernet 10/100 MBit/sSignal inputs: 1 x optocoupler (configurable)- Input voltage: 0 to 30 VDC ULow < 2 VDC, UHigh > 6 VDC- Input current: 4.5 mASignal outputs: 1 x relay (configurable NO/NC)- Switching voltage: max. 30 VAC/DC- Continuous current: max. 2 A - Switching power: max. 60 VAConnection terminals: 0.5 to 1.5 mm2Housing material: - GAT Access 6100 F: plastic- GAT FR 055: plasticPermitted ambient temperature: -10 to +55°CStorage temperature: -20 to +70°CRelative humidity: 20 to 80%, non-condensingProtection type: IP 54Protection class: IIIWeight: 0.2 kgEnvironment classbased on VDS 2110: II (conditions in indoor areas)Certifications of the GAT FR 055 finger scanner: CE and FCC152www.gantner.comTechnical data93 mm (3.66”)93 mm (3.66”)33 mm (1.3”)107 mm (4.21”)2347798163 mm (6.42”)56139.4 mm (1.55”)38 mm (1.5”)53 mm (2.09”)Typical applicationTurnstileGAT Access 6100 FPower supplyNetworkData carrierDimensions1. 4-segment LED display2. Monochrome display (LCD)3. Function keys4. Illuminated, round scan field5. Device back part6. Device upper part7. Fingerprint reader GAT FR 055 (optional)8. Fingerprint sensor of the GAT FR 0559. Weather protection cover (optional)Valid as from July 31th 2013 • Technical data subject to modifications without notice! DB_GAT-ACCESS6100F--BIO-EN_11.indd • PartNo.: 243526
3www.gantner.comValid as from July 31th 2013 • Technical data subject to modifications without notice! DB_GAT-ACCESS6100F--BIO-EN_11.indd • PartNo.: 243526Mounting and installation instructions1. Mounting holesDrill mounting holes on a flat background (e.g. concrete wall) according to the following dimensional drawing. Use the three holes labelled (a).2. Connection cableThe connection cables (power supply, network etc.) are run through the cable lead-ins of the GAT FR 055. With concealed/flush wiring (1) the connection cables are fed from behind via the back box. With surface wiring (2) the connection cables must lie in the cable duct on the back part of the GAT FR 055.3. Wall mountingPay attention when fixing to an uneven background that the GAT FR 055 housing and the device back part of the GAT Access 6100 F must not be distorted. Recommended mounting height: top edge of device 1.3 m.1. GAT FR 0552. Device back part of GAT Access 6100 F3. Fastening screws4. Connection cable5. Connection cable GAT FR 055 to GAT Access 6100 F6. Weather protection cover (optional)7. Fastening screws for weather protection cover94.4 mm (3.72”)60 mm (2.36”)13 mm(0.51”)69 mm (2.72”)20 mm(0.79”)Flush cabling28.5 mm(1.12”)71 mm (2.8”)157 mm (6.18”)14.1 mm (0.56”)12.6 mm (0.5”)aaa4. Electrical connectionThe connection cables (see (4) in previous drawing) are connected at the device back part of the GAT Access 6100 F (se page 4).5. Mounting of the GAT Access 6100 F upper partThe connection cable of the GAT FR 055 (1) is fixed into the housing upper part of the GAT Acces 6100 F and the connection cable of the upper part (2) is fixed in the back part of the GAT Access 6100 F. After that the device upper part can be swung down into the back part (3).Check the sockets (1) and (2)! Dirt, dust and humidity must be removed so that a good contact of the connection cable is guaranteed. No aggressive detergent may be used. Please do not damage socket contacts.Attention: Cleaning only in powerless state!6. Open the GAT Access 6100 F upper partThe GAT Access 6100 F an only be opened with the supplied special tool! With this the two catches on the bottom of the device can be unlocked in succession.12Back boxMaintenanceThe sonsor field of the GAT FR 055 should be cleaned from time to time so that finger prints can be clearly scanned.For cleaning the sensor field always use a humid (not wet!) smooth cloth. No sharp or acrid detergents and no sharp materials must be used!1673325412321
Electrical connectionsTCP/IP with external power supply4www.gantner.comGAT Access 6100RX +TX -TX +GNDNO 1C 1IN1 -IN1 +RX -VIN +TCP/IPPower supply unite.g. GAT Power Supply SP014/1VOut+GNDABMains powerMotor controlFeedback controlMe.g. Turnstile1Valid as from July 31th 2013 • Technical data subject to modifications without notice! DB_GAT-ACCESS6100F--BIO-EN_11.indd • PartNo.: 243526Power supplyDC supply (see technical data), e.g. via GANTNER GAT Power Supply SP014/1. The power input is protected against reverse-polarity.NetworkEthernet, connection via screw terminals.Recommended cablesEthernet: min. CAT 5 (STP) for 100 MBitEthernet wire coloursEthernet 10/100 MBitUsage of the fingerprint reader GAT FR 055The sensor field will light-up red if a finger print must be scanned.Pay attention that the finger is always pressed vertically onto the sensor field in order to guarantee an optimal scanning of the finger! Furthermore the finger should be laid rectangular onto the sensor field and touch the top edge.See also the operating instructions of the GAT Access 6100 F.568A 568BTX + green/white orange/whiteTX - green orangeRX + orange/white green/whiteRX - orange greenConnection to the device upper partAttention: The socket for the connection cable between the device back part and upper part (circle with the lable (1) in the connection figure) must be clean in order to guarantee a good contact.Relay outputFor activation of devices like turnstiles etc.. the relay contact is of type NO (maker contact). Please observe the max. permitted switching voltages and currents (see technical data).Depending on the connected installation (e.g. turnstile) an additional free-wheeling diode may be necessary, which is used to limit the switch-on current. Please read the documentation of the connected installation.Optocoupler inputInput for status acquisition. For using the input a supply voltage must be applied. This voltage can be taken from the terminal´s supply or from an external power source. Please observe the max. permitted input voltages and currents (see technical data).Correct:Incorrect: Safety instructions- This device must be installed by qualified personnel only.- The applicable safety and accident prevention regulations must be observed.- Safety devices must not be removed.- Please observe the technical data of the device specified on the data sheet.- The device must be disconnected from the power supply prior to installation, assembly or dismantling.

Navigation menu