Gantner Electronic GEA1150002A Access Control Terminal, Access Control Terminal with Biometry User Manual Brochure 6100F
Gantner Electronic GmbH Access Control Terminal, Access Control Terminal with Biometry Brochure 6100F
Contents
- 1. User Manual
- 2. Brochure 6100
- 3. Brochure 6100F
Brochure 6100F
GAT Access 6100 F Access Control Terminal with Biometry Application The GAT Access 6100 F with fingerprint reader GAT FR 055 is a stylish terminal for access control in leisure facilities such as swimming pools, spas and gyms. Identification at the terminal is by contact-free RFID data GAT Access 6100 F carrier (Radio Frequency Identification). With the fingerprint reader GAT FR 055 access control is extended by verification with biometric data, which enables optimal protection against misuse of personal data carriers. Information for user guidance is displayed via a graphical monochrome display (LCD). Fingerprint reader GAT FR 055 Function description Order information The GAT Access 6100 F reads contact-free data carriers and checks Description PartNo. GAT Access 6100 F 776487 and grants authorisations. The user holds the data carrier over the round scan field and selects the required service via the acknowledge key. The integrated 4-segment LED display, monochrome LCD display and acoustic signal indicate authorisation. Via the fingerprint reader GAT FR 055 the identification of the visitors is verified by comparing their fingerprints with the fingerprint templates (two templates per visitor) stored on the visitor‘s personal data carriers. The combination of RFID data carriers and fingerprints allows for optimal protection against misuse of data carriers. For capturing the fingerprints and storing them to the data carriers the GAT Access 6100 F Enrollment Station is used. Terminal for entry control with integrated, contactless MIFARETM reader, with black-white display (LCD) GAT FR 055 557433 Fingerprint reader for GAT Access 6100 F, wall mounting GAT FR 055 Weather Cover 174529 Weather protection cover for GAT FR 055 and GAT FR 055 FIU 3k Highlights • Activation of turnstiles, doors etc. via relay output • Feedback input • User guidance via monochrome display (LCD), 4-segment LED display, illuminated round scan field and beeper • Secure data transmission between reader and data carrier • Read/write frequency 13.56 MHz • Reading MIFARETM Standard data carriers • Expandabilities for verification via fingerprint • Opening of housing only possible with special tool • Plug & Play installation www.gantner.com Accessories Description PartNo. GAT Access 6100 F Enrollment Station 174327 Table station for capturing fingerprints GAT Reader WK 581683 Tool to open the reader housing Valid as from July 31th 2013 • Technical data subject to modifications without notice! DB_GAT-ACCESS6100F--BIO-EN_11.indd • PartNo.: 243526 Technical data Nominal voltage: 12/24 VDC (SELV - safety extra-low voltage) Control elements: - 4 function keys - RFID reader Permitted input voltage: 10 to 28 VDC Host interface: Ethernet 10/100 MBit/s Aver. power consumption: - Full operation sensor in: 4.5 W - Full operation sensor out: 3.5 W Signal inputs: Data storage: Internal EEPROM memory for configuration and booking memory, data preservation min. 10 years 1 x optocoupler (configurable) - Input voltage: 0 to 30 VDC ULow < 2 VDC, UHigh > 6 VDC - Input current: 4.5 mA Signal outputs: Internal clock: Data preservation approx. 12 h (Gold-Cap) Reader type: MIFARETM Standard 1 x relay (configurable NO/NC) - Switching voltage: max. 30 VAC/DC - Continuous current: max. 2 A - Switching power: max. 60 VA Frequency reading field: 13.56 MHz Connection terminals: 0.5 to 1.5 mm 2 GAT FR 055 sensor: - Scanner type: optical sensor, 500 dpi @ 8-bit per pixel, active area: 13 x 20 mm - Verification time: < 0.8 sec. - Identification time: < 1 sec. - False acceptance rate 0.01% (recommended), adjustable over wide range Housing material: - GAT Access 6100 F: plastic - GAT FR 055: plastic Display elements: - Full graphical monochrome display (LCD) with white LED background lighting, resolution 128 x 64 pixels, visible area 50 x 25 mm - RFID reader (illuminated) - Acoustic signal - 4-segment LED display with different colours Permitted ambient temperature: -10 to +55°C Storage temperature: -20 to +70°C Relative humidity: 20 to 80%, non-condensing Protection type: IP 54 Protection class: III Weight: 0.2 kg Environment class based on VDS 2110: II (conditions in indoor areas) Certifications of the GAT FR 055 finger scanner: CE and FCC15 Dimensions 93 mm (3.66”) 39.4 mm (1.55”) 33 mm (1.3”) 107 mm (4.21”) 163 mm (6.42”) 1. 4-segment LED display 2. Monochrome display (LCD) 3. Function keys 4. Illuminated, round scan field 5. Device back part 6. Device upper part 7. Fingerprint reader GAT FR 055 (optional) 8. Fingerprint sensor of the GAT FR 055 9. Weather protection cover (optional) 93 mm (3.66”) 38 mm (1.5”) 53 mm (2.09”) Typical application GAT Access 6100 F Power supply Network Data carrier Turnstile Valid as from July 31th 2013 • Technical data subject to modifications without notice! DB_GAT-ACCESS6100F--BIO-EN_11.indd • PartNo.: 243526 www.gantner.com Mounting and installation instructions 4. Electrical connection Drill mounting holes on a flat background (e.g. concrete wall) according to The connection cables (see (4) in previous drawing) are connected at the the following dimensional drawing. Use the three holes labelled (a). device back part of the GAT Access 6100 F (se page 4). 14.1 mm (0.56”) 1. Mounting holes 94.4 mm (3.72”) 69 mm (2.72”) 60 mm (2.36”) 13 mm (0.51”) 5. Mounting of the GAT Access 6100 F upper part The connection cable of the GAT FR 055 (1) is fixed into the housing upper part of the GAT Acces 6100 F and the connection cable of the upper part (2) is fixed in the back part of the GAT Access 6100 F. After that the device upper part can be swung down into the back part (3). 71 mm (2.8”) 157 mm (6.18”) 28.5 mm (1.12”) 12.6 mm (0.5”) Flush cabling 20 mm (0.79”) 2. Connection cable The connection cables (power supply, network etc.) are run through the cable lead-ins of the GAT FR 055. With concealed/flush wiring (1) the connection cables are fed from behind via the back box. With surface wiring (2) the connection cables must lie in the cable duct on the back Back box part of the GAT FR 055. Check the sockets (1) and (2)! Dirt, dust and humidity must be removed so that a good contact of the connection cable is guaranteed. No aggressive detergent may be used. Please do not damage socket contacts. Attention: Cleaning only in powerless state! 6. Open the GAT Access 6100 F upper part The GAT Access 6100 F an only be opened with the supplied special tool! With this the two catches on the bottom of the device can be unlocked in succession. 3. Wall mounting Pay attention when fixing to an uneven background that the GAT FR 055 housing and the device back part of the GAT Access 6100 F must not be distorted. Recommended mounting height: top edge of device 1.3 m. 1. GAT FR 055 2. Device back part of GAT Access 6100 F 3. Fastening screws 4. Connection cable Maintenance 5. Connection cable GAT FR 055 The sonsor field of the GAT FR 055 should be cleaned from time to time to GAT Access 6100 F so that finger prints can be clearly scanned. 6. Weather protection cover (optional) 7. Fastening screws for weather For cleaning the sensor field always use a humid (not wet!) smooth cloth. No sharp or acrid detergents and no sharp materials must be used! protection cover www.gantner.com Valid as from July 31th 2013 • Technical data subject to modifications without notice! DB_GAT-ACCESS6100F--BIO-EN_11.indd • PartNo.: 243526 Electrical connections TCP/IP with external power supply GAT Access 6100 e.g. Turnstile GND VOut+ Mains power Motor control Power supply unit e.g. GAT Power Supply SP014/1 TX + TX RX + RX - GND C1 NO 1 VIN + IN1 + IN1 - Feedback control TCP/IP Power supply Connection to the device upper part DC supply (see technical data), e.g. via GANTNER GAT Power Supply Attention: The socket for the connection cable between the device back SP014/1. The power input is protected against reverse-polarity. part and upper part (circle with the lable (1) in the connection figure) must be clean in order to guarantee a good contact. Network Ethernet, connection via screw terminals. Relay output For activation of devices like turnstiles etc.. the relay contact is of type NO Recommended cables (maker contact). Please observe the max. permitted switching voltages Ethernet: min. CAT 5 (STP) for 100 MBit and currents (see technical data). Depending on the connected installation (e.g. turnstile) an additional free- Ethernet wire colours wheeling diode may be necessary, which is used to limit the switch-on Ethernet 10/100 MBit 568A current. Please read the documentation of the connected installation. 568B TX + green/white orange/white Optocoupler input TX - green orange Input for status acquisition. For using the input a supply voltage must be RX + orange/white green/white applied. This voltage can be taken from the terminal´s supply or from an RX - orange green external power source. Please observe the max. permitted input voltages and currents (see technical data). Usage of the fingerprint reader GAT FR 055 The sensor field will light-up red if a finger print must be scanned. Pay attention that the finger is always pressed vertically onto the sensor field in order to guarantee an optimal scanning of the finger! Furthermore the finger should be laid rectangular onto the sensor field and touch the top edge. See also the operating instructions of the GAT Access 6100 F. Correct: Incorrect: Safety instructions - This device must be installed by qualified personnel only. - The applicable safety and accident prevention regulations must be observed. - Safety devices must not be removed. - Please observe the technical data of the device specified on the data sheet. - The device must be disconnected from the power supply prior to installation, assembly or dismantling. Valid as from July 31th 2013 • Technical data subject to modifications without notice! DB_GAT-ACCESS6100F--BIO-EN_11.indd • PartNo.: 243526 www.gantner.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.2-c003 61.141987, 2011/02/22-12:03:51 Create Date : 2013:08:02 10:14:50+02:00 Modify Date : 2013:08:02 10:14:53+02:00 Metadata Date : 2013:08:02 10:14:53+02:00 Creator Tool : Adobe InDesign CS5.5 (7.5) Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 8102 bytes, use -b option to extract), (Binary data 8026 bytes, use -b option to extract) Instance ID : uuid:666fb2c6-5e9a-4d23-b302-ec7f70d44c44 Original Document ID : adobe:docid:indd:9a31ecbf-aec1-11e0-8d61-e9a41f966e04 Document ID : xmp.did:D592EDC630F9E211B67ED2B328B26BF9 Version ID : 1 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:6531EBC630F9E211B67ED2B328B26BF9 Derived From Document ID : xmp.did:B39EA4AE2FF9E211B67ED2B328B26BF9 Derived From Original Document ID: adobe:docid:indd:9a31ecbf-aec1-11e0-8d61-e9a41f966e04 Derived From Version ID : 1 Derived From Rendition Class : default History Action : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:D40CF1225EADE011A004E54DF7110F6E, xmp.iid:D50CF1225EADE011A004E54DF7110F6E, xmp.iid:8331ADAE2AF9E211B67ED2B328B26BF9, xmp.iid:B39EA4AE2FF9E211B67ED2B328B26BF9, xmp.iid:B49EA4AE2FF9E211B67ED2B328B26BF9, xmp.iid:A905C84B30F9E211B67ED2B328B26BF9, xmp.iid:AA05C84B30F9E211B67ED2B328B26BF9, xmp.iid:6531EBC630F9E211B67ED2B328B26BF9, xmp.iid:D592EDC630F9E211B67ED2B328B26BF9, xmp.iid:48FDD514B8F9E211B520E82860B46321, xmp.iid:D7851BE2B9F9E211B520E82860B46321, xmp.iid:3B6932C3C2F9E211B520E82860B46321, xmp.iid:0F7FF952D7F9E211B520E82860B46321, xmp.iid:4BDE7561D7F9E211B520E82860B46321, xmp.iid:2A6806964BFBE2119A8B98853CEB123B History When : 2011:07:13 16:41:04+02:00, 2011:07:13 16:41:04+02:00, 2013:07:30 17:49:56+02:00, 2013:07:30 17:49:56+02:00, 2013:07:30 17:53:47+02:00, 2013:07:30 17:54:19+02:00, 2013:07:30 17:57:22+02:00, 2013:07:30 17:57:46+02:00, 2013:07:30 17:57:46+02:00, 2013:07:31 10:06:19+02:00, 2013:07:31 10:19:13+02:00, 2013:07:31 11:22:46+02:00, 2013:07:31 13:49:58+02:00, 2013:07:31 13:50:22+02:00, 2013:08:02 10:14:43+02:00 History Software Agent : Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5 History Changed : /;/metadata, /metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata Format : application/pdf Description : 20130802 (WER): GAT FR 050 durch 055 ersetzt (auch Weather Cover)..20130731 (WER): Anschlussbild Seite 4 geändert (Kontakt Drehkreuz), Rechtschreibfehler bei techn. Daten Seite 2, MIFARE (TM) statt (R),.FREIGABE V1.0 Doc Change Count : 2897 Producer : Adobe PDF Library 9.9 Trapped : False Page Count : 4 Creator : Adobe InDesign CS5.5 (7.5) Subject : 20130802 (WER): GAT FR 050 durch 055 ersetzt (auch Weather Cover)..20130731 (WER): Anschlussbild Seite 4 geändert (Kontakt Drehkreuz), Rechtschreibfehler bei techn. Daten Seite 2, MIFARE (TM) statt (R),.FREIGABE V1.0EXIF Metadata provided by EXIF.tools