GuangZhou Walkera Technology DEVO-10 2.4GHz Transmitter User Manual part 2of8
GuangZhou Walkera Technology Co., Ltd 2.4GHz Transmitter Users Manual part 2of8
Contents
Users Manual part 2of8
cJeUention, DEvD—flD Weicome 10 use the DEVO-101ransmitter 11.0 Installa on req ment for rece ver (1) it is imoonantto correctly mount your radio system in your model Below are some advices on now to inslail your equipments (2) Wrap the receiver With 10mm thickness oolyroam and fix it with a rubber band or magic string on your helicopter or airpiane lt heips protect the receiver. (3) it is necessary for you to use rubber grommets and copper sleeves to isolate the vibration trom the main body. The mounting screws cannot be averrtightened. Otherwise. the rubber grommets wili be distorted and decrease the Vibration absorption effect. (4) When mounting the servos. make sure the servos' bell cranks can move ireeiy over theirwhole travel range and ensure the control linkages don't touch or impede the movement otthe servos. (5) if installing various switchesblease keep them far away from the engine tuned pipe and high vibration sources. Ensure all the sWitches move treely over their whole range. (a) Don't make the receiver antennas wrapped or paraliei 11.1 Receiver Frame rate setting There are 11Millisecond and 22 Millisecond Frame Rate. When using 11 Miiiisecond frame rate, It can't be Campatibie with Analog servos Piease seiect the 22 Mliilsecond one if use Ancicg serves (1) LED indicator Ree LED indicates 22ms frame rate; Blue LED indicates 11ms lrame rate, Red&Biue LED indicate the irame rate IS under setting. Redai Blue LED flash means both lrame rate can be set; (2) Setting method After TX and RX binding. press the switch with the moi pen or screwdriver. both indicators WiiI turn on. About 5 seconds. both indicamr Wilifiash.1hen release the switch and press i| crice again. the frame rate can be changed and the indicators wiii turn red or him) oniy Red means 22rns irame rate arid Biue means 11rns. DEvmam—H cieUethion DEvD/i D 2 0 Installat on requ rement for DE 10 battery pack Open the battery cover or DEVO—io transmitter and take out the battery box. Then put a ceiis AA battery or the same Size iuii charged NIMH battery into the battery box. Please check again to make sure the polarities are correct. Welcome in use the DEVO-i D transmitler Warning Do not put the polarities of batteries in the opposite directions. When insert the battery box connector to the transmitter connector. piease make the toai proof is right. showing as beiow pictureThen but the battery box back to battery case. Anode oi the battery Cathode or the battery Battery box (cola proof piug Cathode bithe battery Anode ar the battery Note ityou don't use the Irarismitterpiease take cm the battery 12.1 DEVO-10 Battery Charging Warning the CHG socket is only used for [he rechargeabie NiMH batteries. If using the batteries which is unchargeable The CHG socket is not aliowed to use CHG Charging Socket Charge sockel (CHG) input DC at12V‘ SOmA‘ Puiarily 0—149 Baum—12 cleUen ion D EVCJ - ”I C] All the (unctional settings. which are relahve to the Part two operation system oi DEVO-10 use”, are itu integrated in System Menu. They mclude ' Language, Display‘ Buzzer. vwbratcr, Stwck Mode, H e I I co pte r Shck Direction.Shck ca‘ibration, and About. oleUerlllori DEvor'i D 1 0 Syste Menu All the functional settings, which are relative to the operation system at DEVO—10 itsell, are lully integrated in System Menu. They include Language, Display, Buzzer, vibrator, Slick Mode, Stick Direction,Stick calibration, and About Below is the boot screen of helicopter Welcome to use the DEVO—tO transmitter Elevator trim Throttle tilrii Transmission power display Battery volume display Model name Timer display Model type display Throttle percentage value Ruddertrlm display gilel‘bn trim isp ay 1.1 Language setting Press ENT to enter System Menu and then press UP or DN to move the navigational mark to select System menu. Then push ENT to enter System menu Press UP or DNtc select Language and press ENT to enter the language interface Press UP or DN to select the language that you want. A "w" will be shown on the screen after selected Push EXT to exit lrlrlllzlil 1.1 Language setting 1.2 Display 1.2 Display Press ENT to enter the main menu and push UP or DN to move the navigational mark to select system menu Press ENT to enter System Menu and then press UP or UN to select Display to enter "Display"lnter'ace Three Items are available to be set. Below are the setting methods forthem (1) Backlight contrast: the backlight contrast is adlustable by pushing UP or DN to move the nawgational mark to the digits after Contrast Press R key to increase the backlight contrast, while press L to decrease it (2) Baoklight lightness the backlight lightness is adiustable by pressing UP or DN to move the navigational mark the digits after Lightness The power consumption will be increased if the backlight lightness is too bright and the battery cruise duration Will be shortened Press R or L to increase or decrease the lightness When the value is one means turn ottthe backlight. (a) Eackllghl time out it is possible to set the duration which LCD stays at highlight in the torm ot “Always on or any period from 5 to so seconds with an interval ors seconds Press UP or DN to move the navigational mark to select the digits atter Timeout Press L to short the time of hacklight duration or keep it in the torm oi “Always on" while push R or prolong the time. The maxium is 605. Press EXT to exit. uevm—m—M oleUenlion DEvcls’Icl Welcome to use the DEVO—10 transmitter 1.3 Bnuerwarnlng Pressing ENT to entertne main menu and pressing up or DN to move the navigational marktc select system menu then pusing ENT to enter System menu Pressing up or DN to select Buzzerane pressing ENT to enter the buzzer interface (1) StatustThere are On and off two status on the Buzzer interface. Pressing UP or DN to move the navigational mark to the status option. Pressing R or L to change the ON or OFF status. It includes Thro stiok,knobs and Tones items underthe status is on. (2) Throttle stick buzzer: Pressing UP or UN to move the navigational mark to Thro Stick item then pressing R or L to change the status from inhibit to Active.When Buzzer is at the status ot On. if Throttle Stick is set as “Active". a relative musical scale will make response when moving the throttle stick. You can judge the position of the throttle stick according to the different musical scales. Also, it can be set as lnhiblt. Press UP or DN to move the navigational mark to Thro Stick item and push R or L to change the status irom Inhibit to Active (3) Knobs midpoint Buzzer: When Buzzer is at the status of On, if Knobs is set as “Active".there is buzzer sound when you turn the AUX4 and AUXS to the midpoint. It you don't need the buzzer sound. please change the status to Inhibit (4) Buzzer tune: the tone is composed of in grades. You can choose the favorite one according to your interests. Press UP or DN to move the navigational mark to Tone item and press R or L to make a listening test. Press EXT to exit 1.4 Vibmtor The vibrator used as an alarm function to remind the users. Press ENT to get the Mam Menu, press UP or DN to select System Menu And then press ENT to get System Menu, press UP or DN to select Vibrator Press ENT to get Vibrator setting interface There are two status as inhibit and Active Press R or L to select Active if need Press EXT to exit after finished. ‘ir’itlrailjr itll‘atizlr Etatu 1.5 Stick Mode Press ENT to get Main Menu, press UP or DN to select System Menu, and then press ENT to the System Menu, press UP or DN to select Stick Mode. and press ENT to get stick Mode setting interiace Eitit' t-lljlje Stirs" [Hilde W ilr'lLlle l ‘" ' ' l‘i'l'i'fle l".-'l|:|l:l ' i‘t'lljde J (flop-LI Marie 4 Made 4 " U DEvD—itlf’IE oleUenlion DEvD—1D Welcome to use the DEVOa10 transmitter Sill. , Mild. Mode l ll-1l:lle 1 Made 2 Select the stick mode according to the throttle mode showing on the screen Deva—10 offers 4 stick modes. please reler to “8.0 Switches exchange between left—hand and right—hand throttles Press EXT to exit afler finished. 1.6 suck Direction Press ENT to get Main Menu, press UP or UN to select Eli ' ' ' tEl System Menu, and then press ENT to the System Menu, —————- press UF' or DN to select Stick Direction. and press ENT E | El "981m to get stick direction setting interface. Stick Direction:There are tour items available as Elevator. am, | Aileron, Throttle and Rudder. Press UP or DN to select the Al | Erlj |'| slick which will change direction, and press R or L to change the direction The factory setting is Normal lll t] in 1.7 suck Callbratlcn it is a function to re-calibratian when stick unusual Calibration method: Press "ENT" to the Main Menu, press UP or DN to select System Menu. then press ENT to System Menu. Press UP or DN to select Stick Calibration and press ENT to the Stick Calibration setting interlaoe.Press ENT to enter Calibrationand below interface shows: llbl‘lililrl (El ENT Calibrate Clockwise or counter clockwise mechanically move the right stick and left sticks from minimum levels to maximum levels several times, and then return the sticks to the neutral positions, respectively it will shows the calibration is successful afleryclu press ENT to confirm. Press EXT to exit after finished. 1.5 About Press "ENT' to the Main Menu. press UP or DN to select System Menu. then press ENT to System Menu. Press UP or DN to select About and press ENT to the About setting interface. Press EXT to exit after finished DEVO-iD—ls oleUeniion DEvD—flD 0 Model Menu Model Menu manages all the model data saved in DEVOr10. it includes Model Select, Model Name, Model Copy, Model Trensmil, Model Receive, Model Reset, Type Select, Trim System, Stick Pcsilion Switch, Device Select. Device Output. swash Type. Power Amplifier, Fixed D and Sensor setting Welcome to use the DEV0710 transmitter 2.1 Model Select Press ENT to get Main Menu and press UP or DN to make Model Menu is selected. Press ENT to get the Model Menu and press UP or DN to select Model select, press ENT to get the Model Select setting intertace. Press UP or UN to select the model you desired. Dress ENT to oonfirrrl and marks" x/"in the front of selected one. Total 30 models are optional Press EXT to exit attertinished. 2.2 Model Name ln the menu of model name, you can make a desired name for your model for long term storage lts data can be directly withdrawn in next llights Repeat the step “2 i Model Select" to choose the model you want to name or save. press EXT to back to the interface. Press “ENT" to enter Main Menu, press UP or DN to select l .1L “j til M It l E "MODEL Menu", then Press "ENT" to enter Model Menu; Press UF' or DN to select "Model NAME" and then press “ENT” button to get lhe "Model Name" setling interiece Press UP or DN to select the character and figure which are needed lo be changed, press R or L button to change lhe characler and figure, and press UP or DN to set nexl one Press EXT to exit after finished 2.3 Model Copy Press ENT to get “Main Menu" and press UP or DN to make “Model Menu“ is selected Press ENT to get "Model Menu" and press UP or DN to select" Model Copy", press ENT to the "Model Copy" setting interface. Press UP or DN to cheese the model you want to be copied as source model and press ENT to confirm, The serial No and model name of Source Model will be shown as below photo. lerE of] “q MOD Then press UP or UN to locate the source model. press ENT to confirm. Then an enquire "Are you sure?" is popped up as below photo. Press ENT lo copy, or press EXT to exit. Are you sure? DEvD-1D—17 oleUenlion DEvD—1D Welcome to use the DEVO—10 transmitter 2.4 Model wireless copy The model data between two DEVO-10 equipments can be wirelessly copied via Model Transmit and Model Receive in Model Menu (1)Model transmission l‘v'lUElEl TI-Eil'. ‘-' I'llll Press ENT to enter "Main Menu" and press UP or DN to select "Model Menu". Press ENT to get "Model Menu" and press UF' or UN to select “Model transmission", continue to press ENT to enter "Model Transmit" setting interface. Press UP or DN to Choose the source model which will be transmitted, and press ENTto oonhrm, an enquiry information “Are you sure?" will be shown as below photo Press ENTto transmit, “Transmitting ...... "appears in the interface. Or press EXT to exit Press EXT to exit after another DEVO-10 received the data Mariel Tran ' ' '. ' El him. i MOD 2 Are 'l-lu sure? (2) Model receiving Press ENT to enter Main Menu and press UF' Dr DN to select Model Menu Press ENT to get Model Menu and press UP or DN to select Model Receiving, continue to press ENT to enter Model Receive setting interface. An enquiry information “Are you sure?" will be shown as below photo l'fl._fl n El El H Ell- Press ENT to receive. “Connecting and “Receiving _ _ I ._ ...... " will be shown in series in the interface. The information Hit": "UU -:' Jll" - oi "Received” with the model name will be shown after receiving is finished Or press EXT to exit. l__..____._... Press UP or DN to choose the save position. an enquiry information "Are you sure?" is shown after press ENT. Press ENT to save or press EXT to exit. Press EXT to exit atter finished. [’LlP ‘l‘leJ‘: ,_;IJ[’. DEvD-io —1€l cleUeniion DEvD—1D Welcome (0 use the DEVO-10 transmitter 2.5 Model resel All llie model dale can be reslored lo faelory sellings via Model Resel. Press lhe ENT lo gel Main Menu and press uP or DN lo M El El El Fl E‘ seleol Model Menu. Press ENT le gel Model Menu and press UF' or DN lo seleel Model Reset, press ENT lo gel M 0d El Al Model resel selling inlerface. ll is possible lo slore up lo so models dala in the model lisl of DEVO-1D equipmenl There are two melhods to reset the model data: batch reset and single resel Belch resel: press UP or DN lo seleol All Models, an enquiry inlormelion'are you sure?" will he appears in the inleriace Press ENTto reset all models. or press EXT lo exil Single resel: Press UP or DN lo choose lhe model you wenl lo reslore, “Are you sure?“ will appear afier press ENT Press ENT lo resel or press EXT to exil Press EXT to exit after finished 2.5 Type Select This device offers lwo model lypes menu They are helioopler and airplane respectively Press ENT lo gel Main Menu and press UF' or DN lo seleel Model Menu. Press ENT lo enler and press UP or DN lo seleol Type Seleol and press ENT lo enler selling inlerfaoe. Press “ENT' pullon lo gel Helioopler and Alrplane selecllons and press UP or DN lo seleol and press ENT lo confirm, then press EXT In 5in 2.7 Trim System Trim System is able to finely lune the following six items. respectively: Elevator. Ailercn, Rudder, Throttle. Lefl Trim and Riglil Trim. The lrim range is divided inlo 20 grades (factory defaull is sel al 4) ll is oonvenieni lo sublly modify lhe pilch by adjusling lhe Irim range Press ENT In yet Main Menu and press UP or DN Io selecl Model Menu Press ENT (0 enter and press UP or DN to select Trim System, press ENTto enter setting interlaoe DEvD—4 D 719 m— Welcome to use the DEv0-10 transmitter DEVD/lci Press UP or DN to seiect the trim which wiii set. press R to increase the trim value and press L to reduce. Por eievator, aiieron, anoi rudoer. there are two more options: Normal and Limited. press R or L you can change the setup. “Normal" means the trim is always working although the corresponding stick stays anywhere. “Limited" means the trim is out of working when the corresponding stick is at maximum position. Iernn Norm Press EXT to exit after finished. 2.8 Stick Posl on Switch According to the following setting, the switch can be used as a switch The turnrnn or turn—o" position at which stick stays can also be settable Methoo tor setting: Press the EMT to get Main Menu and press UF' or DN to ._. Mn; h seieot Model Menu. Press ENT to get Model Menu and ,.. C: press UP or DN to select Stick Position Switch, press ENT to get Stick Position Switch setting interface (A. l'I‘le'll'l p] e- i. e There are iour options under the stick postion swnoh: SPSO. . . SF31.SF32.SF33 Press R or Lio choose the switch you in il l lZI it want to define. Press UF' or DN to inhibit channel in navigation mark, and press L to expand the menu.The channel includes four items: Elevator, Aileron, Throttle and Rudder. The tactory default is Inhibit. Take Elevator for example. Press R or L to choose the Eievator as stick, then Press UP or DN to move nagivation mark to value oi position. It’s possible to adjust the stick position via pressing R or L. , iiiijn Press UP or UN to navigate the OPEN settingrpress R or L to change the direction at the channel stick Press UF' or UN to navigate the STATUS, which can check the sketch map of the stick OPEN/CLOSE direction. Check if it was set correctly Arterfinisheo the settingpress EXT to exit DEvU-1 Cl — EU oleUention DEVCJ—io Welcome to use the DEVO—iD transmitter 2.9 Device select This setting can heip you configure various tuncticnei switches, or adjust ievers. lt inciuoes Flight Mode Switch, Stunt Trim Select, Throttle Hold Switch, Hover pitch select, Hover throttle select Press ENT to enter Main Menu. press UP or DN to move navigation mark to select Model menu. Press ENT to enter Mooei menu function. Press up or DN to seiect Device Option. Press ENT to Device Option interface. (1) Flight Mode Switch:Press UP or UN to move navigation mark to Flight Mode Switch item and press R or L to select the desired switch The factory default setting is FMOD switch (2) Stunt Trim Select:There are two modes: Common and F Flight Mode In Common mode all the trim values, which _'; D m m 1] |'| various sticks are corresponding to. put equally effects on all the flight modes In Flight Made. the trim value. each or which stick is corresponding to. puts independently eireci on the corresponding stick. The rectory default setting is Common Press UP or DN to Choose the Stunt trim select , press R or L to select “Common"or Flight mode,the factory default setting is Common. (3) Throttie Hold Switch:Reters to “(1) Flight Mooe switch" (4) Hover pitch seiect:Rerers to "(1) Flight Mode switch” (5) Hover throttle seiect:Rerers to ‘(1) Flight Mode switch" Aiterfinished the setting. press EXT to exit 2.10 Device Output Device output can set up the output switches respectively lt can aiso activate, inhibit or use other functions There are eight items in total: FMOD switch, MIX switch,ELEV D/R switch‘ AILE DIR switch, RUDD D/R switch,GEAR switch. SPSO, SPSL SPSZ. SPS3. left trim. right trim. AUX4 knob.AUX5 knob Setting: * - ‘luiput Press ENT to enter main menu. press UP or DN to move navigation mark to Model Menu. Press ENT to enter Model menu. Press UP or DN to select Output device and press I _ ENT to enter Output device interface. 6 E AR 8 W Fu n i::ii u n There are 5 settings:Gear, AUX2.AUX3,AUX4,AUX5. (1) Gear Press UP or DN in OUTPU interface can change the gear switch lt includes FMOD, MIX ELEV DIR, AlLE D/R. RUDD DIR, GEAR. SPSO, SPS1. SPSZ, SPS3, Left trim, Right trim, AUX4 knob. AUX5 knob Press R or L to select the setting switch, The default setting is GEAR SW. Press UP or DN to select Function setting after you select the switch,F'ress R or L can enter the interface of Gear activatejnhibit and Governor The default setting is Activate. You can continue to set others items after finished. .. Clutput mi ' . iiiuiput GEAR SW ' [SE-“ii, l' i"-'u Fu n [it u n Fu ri ml u n (z) AUX 2 Press UP or UN to enter the AUX2 intertacePress R or L can change the AUX2 switch. lt includes FMOD. MlX. ELEV DIR. AlLE D/RRUDD D/R.GEAR.SPSO.SP31.SP52.SPS3.Left trim.Right trim,AUX4 knob,AUX5 knob,The oereuit settlng is won svvitch. DEW} 1 0 7 21 oleUenlion DEvD—1D Welcome to use the DEVOr‘lD transmitter Press UP or DN to select the Function setting, press R or L to choose the switch. it inculdes inhibit. activate, Gym. Govemur. the default setting is Gym. You can cuntinue to set others items after finished . tiiitutDui t: Fun tzzti D n FL! rt tzzti D l'l fit-“m _ (3) AUX3 Press UP or DN to enter the AUXS interface. Press R or L can change the AUX3 switch. It includes RUDD D/R,GEAR,SPSO,SPSi,SPSZ,SPSS,Lefl trimRtght trim,AUX4 knob,AUX5 knub,The default setting is RUDD D/R switch Press UP or DN to move navigation mark to FuntiDn setting. Press R or L to desired item.The optional items are Inhibit. Active, Gyro and Governor. The factory defautt is Active. Continue to set up other items after setting finished "tutDut tlfii til utD ut RUDD D R ‘ FiLIDD Dir: Fu rt Dti D n Fu I'I tzzti D n (5) AUX4,AUX5 settings please refers to the AUX3 settings AUX4 default setting is AUX4 knob, AUXS de'ault setting is AUX5 knob. After finished the setting. press EXT to exit. 2.11 Swasir Type The swash type is grouped into five options: 1 Servo Normat, z Servos 130°, 3 Servos 120°.3 Servos 140°. 3 Servos so" and 4 Serves 90". Press “ENT" key to enter Main Menu, press UP or DN until “MODEL" flash . and then press “ENT" key to enter Model Menu: Press UP or DN choose"SWASH"press ENT enter to Swash setting intertace. 3-139- v’l SEND Drmal Press up or UN to choose the requiring swashptate type. Press ENT to confirm then the corresponding items witt 3 ._rEl' 1V is. have the’K/"mark in tront of the items.F'ress EXT to exit a ¢._ . _ . ~:. afterflnished. z: xjtsllivlLla NU 2.12 Power Amplifier The transmission output power of DEVOeiD is adjustable. it is divided into six grades trom smatt to big The tower the transmission output power transmits, the shorter the radio range is, and the tonger the standeby time will be, the higher the transmission output power, the farer the radio range, and the shorter the stand— by time Choose the appropriate transmission output power eocording to the actual situation Press ENT to enter the main menu Press UP or DN to choose "Model menu“and then press ENT to enter the intertaos Press UP or DN to choose the appropriate output power, press ENT to confirm DEVD>1D —22
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Modify Date : 2012:03:23 18:37:55+08:00 Create Date : 2012:03:23 16:09:25+08:00 Metadata Date : 2012:03:23 18:37:55+08:00 Format : application/pdf Document ID : uuid:e8127558-42e4-42d3-84d8-c5e0144e9620 Instance ID : uuid:c61259d7-5a3f-4a17-aa68-61604b1c6377 Has XFA : No Page Count : 12EXIF Metadata provided by EXIF.tools