GuangZhou Walkera Technology DEVO-10 2.4GHz Transmitter User Manual part 3of8

Download:
Mirror Download [FCC.gov]
Document ID	1672925
Application ID	miIxliB/5/p2AAVCIgjBWQ==
Document Description	Users Manual part 3of8
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	406.85kB (5085563 bits)
Date Submitted	2012-04-10 00:00:00
Date Available	2012-04-10 00:00:00
Creation Date	2012-03-23 16:09:25
Document Lastmod	2012-03-23 18:43:11
Document Title	Users Manual part 3of8

oleUenlion
DEVD'1D
Welcome to use the DEVO—10 transmitter
Press UP or UN to choose the requiring AMPLl Press
ENT to confirm then the corresponding items will have
thewwark in lront oi the items The AMPLI rate will be
shown on the interlaoe
+1IZI EIErl'l
_ Alterthe setting, press EXT lo exil
+5 d E' n l
2.13 Fixed ID
This setting will hind DEVO-1O with its receiver in a unique corresponding relationship It will greatly speed
up me time of automalic binding when DEVO-10 powered on
(1) Setting lor fixed la
The setting for fixed us should be under the status that automatic ID binding is successfully finished Below
is the setting method
Press ENT to enter the main Menu and push UP or UN to move the navigational mark to select Model menu
Press ENT to enter Model Menu Press UP or UN to select Fixed lo and press ENT to enter the Fixed ID
setting interface.
ll you want to activate the fixed ID settings, press R or L to change the status from oil to ON A series ol
random digits will be shown below after change to On.
Fl P18 lj ID
Press UP or DN to choose the ID code setting, press H _ _
R or L to coose the words or number,press uP or DN Ci 2:11!) ‘ci
moves to the next code setting . there are 6 words can
be set lo lD code. ”3 E: n d E! |
Press ENT key afler the new lD has been set. An inquiry interface o"‘Are you sure?" pop up. "ID Code Matching
will be shown afler press ENT. After malching, the interlaoe will be relurned to Model Menu.
Fi Ed ID
ID Pidatlizh ......
DEvD-1 D — 23
M]— Welcome to use the DEVO-10 transmltter
DEvD-1D
(2) Fixed lD cancellation
insert the assorted BlND PLUG into the output terminal of BATT before the receiver is powered on‘ and then
plug 5v DC power into other output terminal. The red light of receiver will flash slowly. This means the fixed
ID code has been cancelled Pull out bind plug Devoeto also needs to make relative cancellatlon and revision
after the fixed us in receiver is cleared out
In the main interface press the ENT to enter Medel Menu
and then press UP or DN to move the navigational mark
to select MODEL MENU. Press ENT to enter MODEL MENU.
Press UP or DN to select Fixed lD code and push ENT key
to enter the Fixed lD code interlacePress UP or DN to select
STATUS option, Press R or L to change the status to Off
Then press EXT to exit
2.14 Sonsor setting
Setting method: press ENT enter to the Main menu. Press UP or DN to select the Model menu Press ENT
enter to Model menu. Press UP or DN to select sensor press ENT enter to the sensor setting interlece See
the lllustration
Press R or L select Activate or lnhibit (the default setting
is inhibit), such as press Activate will includes No Signal
Waming.Voltage sensor.Temperature sensor.GPS receiver
setting etc.
(1) No Signal Warning
Press UP or DN to make the navigation mark choose “No
Signal Waming”.Press R or L to choose ' inhibit" or “active"
(default setting is" inhibit"). if you choose “Active”,the Radio
will alarm when telemetry signal lostAs following:
(2) Voltage setting
There are 3 diflerent types of voltage can be measuredlt includes internal 5V,External vt and V: which can
be monitor two different external veltageii e battery) respectively Once the measured voltage is lower than
the setting value. the Radio will alarm.
(z 1) Receiver 5V(lntemal) PFV(Power Feeding Voltage) Alarmed value can be sstted as 3 s-ev
Voltage setting: press R or L to activate the sv, the alarm interface will appears in the interface , please refers
to the lllvstration
Internal: E" -'
Press UP or UN to select the Alarm Voltage settingpress R or L to set the value The range is 3 s-sV you
can continue to set others items alter you finished
DEVO-to—EA
oieUeniion
DEvo—1D
Welcome to use the DEVO-10 transmitter
(z 2) Extevnei v1
Press UP or DN enter to Externai V1 setting interface. Press R or L to activate the V1,the details refers to
the iiiustration
voltage
E: email ‘
3.8 Unli
Press UP or DN select the Alarm voitage setting. Press R or L to set the value The setting range is o.z~99 av.
you can continue to set others items after you finished
(2 3) Externai: vz setting can refers to External v1 setting
Press EXT back to sensor setting intertace after you finished.
(3) Temperature sensor
The temperature sensors can measure up to 4 difierent temperatureti e motors) You can choose Celsius or
Fahrenheit.The aiarmed vaiue can be setted for 4 difterent temperature Once the measured value is higher
then the setting vaiue.the radio wiil alarm.The Aiarm
Temperature value can be setted as —20-220'C or
stills-428.0" F.
Temperature Setting:
in the “Sensor Settlng"interfaoe,press UP or DN to make ln h i D it
the navigation mark cnuuse “Temperature Sensor',and
press ENT to enter “T emperature Sensoflsetting interface
See the iiiustration irl i'I i D it
(3 1) Unit
Press UP or DN to make the navigation mark choose “Unit"setting itemand press R or L to choose Unit, two
kinds Of Uniticeisius and Fahrenheit
(3 2) Aiarm Temperature settings
Press UP or DN select the T1 .Press R OR L activate the setting Inhibit Wiii change to Active and Aiarm
temperature wiil be shown if you choose inhibit, the Aiarm temperature Vaiue Won't be shown.
Press UP or DN select “Alann'setting.press R or L set the
aiann temperature value.Press UP or DN to set other items
after finished the setting.
(3 3) T2.T3.T4 setting
Reier to the step ci“(3 2)T1"
.-. m , _ ,
(4) eps setting U F Ct b‘iil I'I El
There are 4 items including Altitude Type,$peed Unit,Date .fiiiiiU Ij E T‘
type and time Zone in the GPS receiver setling intertace.
Press UF' or DN to seiect the Sensor setting interface
to enter the GPS setting interface.
DEvDr’inEE
oleUenlion
DEvD—1D
Welcome to use the DEVOr‘lD transmitter
(4 1) Altitude Type [3 P ll'l El
Mtilude Tupi;
Fl slat ve
Press UP or DN select the Altitude type on the GPS
setting interface and it’s including Absolute and relative
peed Unit
(4 2) Speed Unit ixl—l DlS
Press UP or DN select the Speed Unit on the GPS setting interface and it's including knots and kmlh and
relative Select the desired item.
BPS S ll'IEl
Mtitude Type
R E. | ati'
ElIIIEed Unit
W h
(4.3) Date Type
Press UP or DN select the of Date Type on the GPS setting interface and it's including DD—MM—YY.MM7DD—
W and YY—MMrDD. Select the desired item.
(4.4) Time Zone
Press up or DN select the at Time Zone . press R or L to set the desired Time Zone
[3 --:- Betting GP... 3 fitting
Date Type
DESI—hm —
Time Ion
(4.3) Date Type (4.4) Time Zone
Function Menu can help you custom adjustments for the selected models The menu includes such items as
Reverse Switch. Travel Adjust, Sub Trim. Dual Rate and Exponential, Thmttle Hold. Throttle Curve, Mix to
Thruttle.Gyr0 Sensor, G0vern0r,Tail Curve, Swash Mix,F'itch Curve, Program Mix, Monitor,Fail Safe, Sensor
View, Trainer and Timer
3.1 Reverse Switch mt): |’| EU
Press ENT in main inlerfaoe to enter main menu; Press UP
or DN to move the navigation mark to Function Menu And Urn-I 31
press ENT to enter Function Menu, Press UP or UN to
choose Reverse Switch and Press ENT to enter into Reverse . .l l E! m n
Switch interface.
N n r m al
DEvD-1D 726
deUenlion,
DEvD—flD
Welcome to use the DEVO-lO transmitter
Press UP or DN to move navigation mark to ELE(lake
Elevator for example).Press R or L to shift the status
between numal and reverse These are two status for
option And the default setting is Normal. All Channels
Reverse Swllch like: Allercn, Throttle, Rudder, Gear, Pitch,
Aux2‘ Aux3‘ Aux4 and Aux5 can be referred to lhe way of
ELE Reverse Switch And press EXT to exit after setting
finished.
3.2 Travel Adjust
Press ENT to enter into main menu Press UP or DN to rnove navigation markto selected itern Function menu.
Press ENT to enter Function Menu Press UP cr DN to select Travel Ajust, Press ENT to enter Travel Adjust
Interface. as below illustralion. lt shows lhe Travel Adjust slatus ol one channel:
Take ELE forexample, Press uP or DN to move navigation
to desired item Eievatioh or U. Press R or L to decrease or
increase the servo travei range. The adjustment range is
trorn o o% to i50.0%. The factory detautt is 100.D%.
Press up or DN to move navigation mark to desired itern
D or ELE. Press R or L to increase or decrease the serve
travel range The range I5 from c u% to i50.c%. The iaetory
- detauit is 100 c%
D I [ll], 1
All other channels Travel Adjust like Aileron. Throttle. Rudder. Geari Pitch. Aux2, Aux3, Aux/3 and AuxS can
be referred to ELE travel Ajust. Press EXT to exit after setting finished
3.3 Sub Trim
Sub Trim can parellel move the neutral point ol the servo But we advise you to mechanically adjust the serve
bell crank it offset is far away from the neutrai point of servo, because excessive usage or the sun trim may
damage the servo.
uti Trim mi ‘
E | E‘ emit r
Press ENT to enter Main Menu, Press UP or UN to move
the navigation mark to desired item Function menu Press l] G96 |
Setting method
ENT to enter Function menu‘ Press UP or DN to select
Sub trim and press ENT to enter Sub Trim interface.
The inlerlace shows the items and the channels which are adjustable Press R or L to change the neutral
paint of Servos The factory default is 0 0% Press UP or DN to choose desired items The range as below
inei t. ~ . ~ . A. ~ . ~
Elevator D62 5%>U62 5% Pitch L62 5%>H62 5%
Aileron R62 5%~L52.5% AUXZ -62 5%~+62 5"/o
Throttle LG? 5%~H82 5% AUX3 -G2 5°/o—~+62 5"/o
Rudder R62 5°/o ~ L62.5"/o AUXA -62 5% ~+62 5"/o
Gear —62.5% ~+62.5"/o AUXS 52 5% ~+62 5"/n
Press EXT to exit after adjustment finished
uevort o— 27
bCleUGI’llIOl’l
DEVO/l D
Welcome to use the DEVO-1O transmitler
3.4 Dual rate and Exponential
it is possible to use D/R switch to control over the dual rate of elevator, aileron, and rudder alter the function
of Dual Rate and Exponential is set up. The setting range is 04257a Under the help with exponential curve
adjustment.ll is not only manually but also automatically able to set up various parameters which are suitable
lor yourself
Selling method
Press ENT to enter main menu Press UP or DN to move
navigation mark to desired item Function Menu Press
ENT to enter Function menu, press UP or DN to choose
Dual rate and Exponential, Press ENT to enter D/R and
Exponential lrlterlace.
(1) Channel selection
Press UP or DN to move navlgallon mark Dl Channel, Press R or l. to sel up Channels containing Elevator,
Alleron and Rudder Choose the desired channel lur sefllng
(2) Position selection
Press UP or DN to move navigation mark to desired item Position.
in the mannual mode, the lunction ot Dual rate and Exponential
Wlll be executed by the corresponding D/R switeh among Poso
and Posl Take the item Elevator at channel as an example
It's possible to shift between Poso and Post via pushing or
pulling the DIR switch.
(3) Dual rate ad)ustment
Press UP or DN to move the navigation mark to desired item Dual Rate lt's possible to change the dural rate
value of Postion via pressing R or L and the corresponding value curve in the right top or lnlerface will be
changed accordingly. The factory default is (om/s.
(4) Exponential
Press UP or DN to select Exponential item or navigation mark it‘s possible to change Dual Rate and Exponential
value in Pos when pressing R or L to change the value There are+100% and Line three ad)ustment AI the
same time. the corresponding curve will be changed and shown at the right graph
Dual Hale rid E:
F tlul'l
F‘El:
RI Fl lP
(3) Dual rate ad)ustrnent (4) Exponential
(5) Automatic setting
Underworking with Plight Mode, it's possible to switch the dual rate and exponential, which are set in abovelal
and (4)Exponential adluslmerll.
Flight Mode
The semmgs lor Normal Mode,Slunl1. SlurllZ and lhrotlle hold
are avallable But Throttle Hold In Funcllon menu should be
set as Aetivelreler ID 3 5Thru|tle Hold below)
DEVDe’l D 7 EH
oleUeniion
DEVD-1O
Welcome to use the DEVO-10 transmitter
(51)Normal FlightMode setting: Press UPorDN inthe Dual Flats EtI'IEl E‘" @
navigation mark of Dual rate and Exponential to select the
desired item Normal Flight Press R or L to set the position E ,..,p [I l'lE! |'|i .3,| r ' 1
and the Switch. Only the D/R switch control is valid When « _
Switch is selected,underthe Flight Mode, it's possible for Li I'l E
Pos lo switch the dual rate and exponential, which are set l'-l l-l t'l'n m M El El P.
in above(3) and (4)Exponential adlustrnent The settings y
for Swtich. Poso, Pos1, P052 and P053 are valid L
(5.2) The selling for stuntl, Stuntz and Throttle l-lold can be setup according to above Normal Flight Setting.
Press EXT to exit afterfinlsh the setting
3.5 Throttle Hold
It this function is set, the switch will be exectuted by hold switch The setting value of throttle hold is ranged
from -20 0-50 0% the default setting is Inhibit
Setting method:
Press ENT to enter main menu, Press UP or DN in move navigation mark to select Function menu Press
ENT to enter Function Menu Press UP or UN to select Throttle Hold, Press ENT to enter Throttle Hold
interface. as below illustration:
Tl’lr'l‘liilP Hl'lllll
Hljllj er cliIJ
Hlilllil F‘u
Press R or L to activate Throttle Hold function, and expansion list will be shown as Throttle hold status, throttle
hold position and Throttle hold switch.
(1) There are two items under Throttle Hold Status: Active and inhibit. The factory default setting is Inhibit
(2) Throttle Hold position
In the Throttle Hold interface, press UP or DN to make the Navigation mark choose “Throttle Hold Posflion"
setting options Press R or L to change data, the minimum value is -20 D%: the maximum value is +50 0%
(3) Throttle Switch setting
It's invalid for setting. the factory default is RUDD D/R which will be shown in the status item When the Throttle
Hold switch is on, data under the Throttle Hold can not be amended until Throttle Hold switch to be oft, and
the hold status is changed.
Press EXT to exit atter setting up finished
DEVO-lD—EQ
dellenlion
DEVD—iD
Welcome to use the DEVO-10 transmitter
3.5 Throttle Curve
Throttle curve are adjusted through seven points, which of all the flight modes can be respectively set The
flight mode includes Normal Flight, Stunti and StuntZ.
Press ENT to enter main menu, Press UP or DN to move navigation mark to select Function menu Press
ENT to enter Function Menu Press UP or DN to select Throttle Curve. Press ENT to enter Throttle Curve
interface Enter Throttle Curve interface, the enquiry dropdown is shown"All servos hold?" lf click OK, all the
servos will be locked at the current status, it click Cancel, all the servers will be unlocked at the current status.
NUDE HDlEl.
I'IEIEl
, . c . .i
l em; ‘I H
(1) Flight Mode
There are total three flight modes: Normal Flight, Stunt1 and Stunt2. The Curve of which can be respectively
set in their corresponding flignt mode. The setting method is to press up or DN to select Flight Mode in Throttle
Curve interface The corresponding itight mode will be shown when the Flight Mode switch shitts via pushing
or pulling the Flight Mode Switch And the exponetial can be adjusted after Flight Mode is selected
(2) Exponential Adjustment Th l’Dl'll E! I' Ll In
Press UP or DN in Throttle Curve interface to move ,
navigation merk oi exponential curve and press R or L FI | g h'[ M it El E
to set the exponential iunction Off and On The throttle N . . . - l
curve will be changed smoothly if touching ON, or in told U t ll l Cl - - .
line if clicking OFF. E n l—lFll-ltlr
(3) Curve settlng
It includes two items: Point and Output
(3.1) Adjustment lor Point
Press UP or DN in Throttle Curve interface to move the navigation mark to desired item Point Press L. an
expansion list including A7L" “71",‘522 “—M”. “—3", “74” and “—H" seven points is shown and can be selected via
pressing R or L
Throttle E: I J rip-t;
P El i rli
.,.r - t ,.
IEfIlE‘lH IElIli‘lH
(3.2) status adjustment
Press UP or UN to move navigation mark to Status and press R or L to choose lnhibit or Activate Click Inhibit
if you don't amend the amount of the selected point. The factory default is Inhibit. Click activate if you want
to amend the amount of the selected point
(3 3) Output adjustment
An expansion list oi Output and Hover items will be shown alter activate the Status Press up or DN to move
navigation mark to select Output item And press R or Lto increase or decrease the amount of selected point
with a minimum of 0.0% and a maximum of 100.0%.
DEvD—1 D 7 SCI
JeUenilon
DEVD'WD
Welcome to use the DEVO-10 transmitter
Thr'tjfilP ut
F'Zlii'li
F'Ellrli — l
iIJ‘
ACtl'tv'E temé-‘tfi
(3.2) status ad)ustment (3.3) Output ad)ustment
(3.4) Hovering Adjustment
After the setting of (3.3) Output adjustment is finished. it‘s necessary to set the item of Hovering as On and
all the selected points of the throttle curve should be activated if using throttle trim in flight is a must.The five
points of 172.M,34 in the curve will being paralleled or down With the changing of throttle trim. So the throttle
curve will being paralleled up or down with the movement of the five points
Press EXT to exit after finish the setting.
3.7 Mix to throttle
This Punction can keep the main rotor blades running at the certain revolution caused by the changed load
when operation the aileron servo. elevator servo and rudderservo Generaly. it's not advised to use hefunction.
Setting method:
Press ENT to enter Main menu in the main interface. Press UP or DN to move navigation mark to select
Function Menu. Press ENT to enter function menu. Press UP or DN to select Mix to Throttle. And press ENT
to enter Mix to throttle interface as In below Illustration
There are three settings elevator, aileron and rudder It the
item of Channel is Shawn as Elevator, there are UP, DOWN
and Switch in the interface If the item of Channel is Aileron
or Rudder. the contents in the said interface will be changed
Into Left Right and Switch Take the example of Channel
set as Elevator to illustrate the setting method.
(1) Up setting
in the Mix to throttle interface. press UP or UN to move the navigation mark to select UP item. Press R or L
to increase or decrease the mix amount when moving the throttle stick upwardsThe bigger the amount is.
the bigger the mix to throttle will be Click the left mark and change the amount from w" to for the throttle
mix direction Reversing. The adiustable range is t‘lZS'Vo.
(2) Down setting
In the interface of Mix to Throttle. press UP or DN to move the navigation mark to select UP item. Press R
or L to increase or decrease, respectively. the mix amount when moving the throttle stick downwards. The
bigger the amount is the bigger the mix to throttle will become Click the left mark and change the amount
from w to forthe throttle mix direction Reversing The adJustable range is 1125%
(3) Switch Selection
in the interface of Mix to Throttle, press UP or DN to move navigation mark to select Switch item Press R or
L. an expansion list of Always on, Normal Mode, Stunt‘i, Stunt2 and Gear is shown After setting finished.
Aileron or Rudder can be set via pressing DN
(4) The setting otAiIeron or Rudder. and Mix to Throttle can be referred to Elevator setting. Press EXT after
setting finished
Notes:
(t) Before the night, please confirm All above amount of mix to throttle is proper enough to offer a good flight
And make sure all the actions in different flight mode are normal
(2) The function is in spare when governor is working. DEVD4 D731
CIGUGHJUOH
DEVO") D
Welcome to use the DEVO-1O transmitler
3.3 Gyro Sensor
This lunction supply the GYRO sensitivrty amustrnentholh Ihmugh swrtch ‘D/R' to Manuel and ”flight mode
"Automalic swncn different sensiliwty
Setting method:
Press “EMT" into "main menu"in Ihe interfacepress
”UP/DN" to choose ”functional menu" Press ”ENT" into
"functional menu":press ”UPIDN" to choose “Gyro Sensol",
ihen press “ENT” into "Gyro Sensor’ interface.
(1) Manual Setting
(1.1) Manual Setting
in the Gyro Sensor interfacepress UP/DN to choose “mode"prcject setpress R/L to seleclahle set ("Manual
set" and “Automatic set") Then choose “Manual" option.
(1.2) Channel
The original channel is "Aux2".il you want to change to other channels control.you can choose from
”Output"set (relerto “2.1 Output")
(1 3) mm choose
in the Gym Sensor interlacepress UPIDN to choose “SWlTCH "projectset.press R/L to selectatile sets ”FMOD
SW“.M1X SW,ELEV D/RiAILE D/RiRUDD D/RiGEAR SW .(o\aHy a selectable sets.Choose the Manual control
swrtoh
(1.4) sensitiwty Setting
If choose 3 switchesxhere are “position O“,"pcsltlcn 1" nd ”position Then set the sensitivity individually/M
Choose 2 swltchefiihere are “pcslilnn 0" and "poslilon 1" (men set Ihe sensltlvliy individually.
(1.4.1) position 0
Turn the chooseo GYRO Control Swilchmake the status
oisplay present sWitch status “position 0" Press UP/DN to
choose “position 0“.press R/L to increase/decrease value
indiwduallyli the GYRO have “NOR"mcde and “AVCS”
mooewhen lhe value lowerthan so%,il is “NOR"mude the
lower ol lhe value is ,the bigger ol lhe GYRO sensitiwty
becomes The factory default value is 50%
(1.4.2) "position 1": position 2" are the seine setting way as above “position 0".
(2) Automatic setling
(2.1) Automatic Setting I
in the Gyro Sensor interlacepress UPIDN to choose Ll lj
"inode"pro)eot set,press RIL to selectable sets (“Manual
set" and “Automatic set“).Then choose “Automatic" option.
h an H E!
(2.2) Channel
The original channel is “Aux2”.it you want to change to other channels control.you can choose from
"output“set.(reier to “2.11 output")
(2.3) Switch there is no use in the Automatic Setting.
(2 A) Slatus
Turn the SWitoh “fllgm mode"or "Throltle hold".|he stalus set display presenl night mode positionThere are
”NormalMode""’Stunt1""'Stur1t2""'thrume hold" sets "Throttle hold" need to slarl that can effect (reler to “3 5
throttle holo")
DEvDr’l D 7 32

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Modify Date                     : 2012:03:23 18:43:11+08:00
Create Date                     : 2012:03:23 16:09:25+08:00
Metadata Date                   : 2012:03:23 18:43:11+08:00
Format                          : application/pdf
Document ID                     : uuid:e8127558-42e4-42d3-84d8-c5e0144e9620
Instance ID                     : uuid:65dbb38d-062e-4529-a818-da4f86a416f2
Has XFA                         : No
Page Count                      : 10

EXIF Metadata provided by EXIF.tools