Honeywell LXE4830P 802.11g COMPACT FLASH MODULE User Manual MX8 User s Guide
Honeywell International, Inc. 802.11g COMPACT FLASH MODULE MX8 User s Guide
Contents
- 1. Manual HX1 rev3
- 2. Manual MX3X rev3
- 3. Manual MX5X rev3
- 4. Manual MX7 rev3
- 5. User Manual HX2
- 6. User Manual MX7
- 7. users manual
- 8. USERS MANUAL
- 9. User Manual MX3X
- 10. User Manual VX3X
- 11. User Manual VX6 part 1
- 12. User Manual VX6 part 2
- 13. User Manual VX7 part 1
- 14. User Manual VX7 part 2
- 15. Users Manual F300
- 16. Users Manual MX9
USERS MANUAL
MX8 User’s Guide For Review - Preliminary - Draft 01 - Not for distribution (Microsoft® Windows® CE 5.0 Equipped) FOR REVIEW – DO NOT PUBLISH OR DISTRIBUTE -- LXE CONFIDENTIAL - DRAFT 01 -- Copyright © 2007 by LXE Inc. All Rights Reserved E-EQ-MX8OGWW-A For Review - Preliminary - Draft 01 - Not for distribution Notices LXE Inc. reserves the right to make improvements or changes in the products described in this document at any time without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, LXE assumes no liability resulting from any errors or omissions in this document, or from the use of the information contained herein. Further, LXE Incorporated, reserves the right to revise this document and to make changes to it from time to time without any obligation to notify any person or organization of such revision or changes. Copyright: This document is copyrighted. All rights are reserved. This document may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine-readable form without prior consent, in writing, from LXE Inc. Copyright © 2007 by LXE Inc. An EMS Technologies Company. 125 Technology Parkway, Norcross, GA 30092 U.S.A. (770) 447-4224 Trademarks: LXE® and Spire® are registered trademarks of LXE Inc. RFTerm® is a registered trademark of EMS Technologies, Norcross, GA. Microsoft®, ActiveSync®, MSN, Outlook®, Windows®, the Windows logo, and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Summit Data Communications, Inc. Summit Data Communications, the Summit logo, and “The Pinnacle of Performance” are trademarks of Summit Data Communications, Inc. Java® and Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. or other countries, and are used under license. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by LXE, Inc. is under license. Hand Held® is a registered trademark of Hand Held Products, Inc., located in Skaneateles Falls, NY. Wavelink®, the Wavelink logo and tagline, Wavelink Studio™, Avalanche Management Console™, Mobile Manager™, and Mobile Manager Enterprise™ are trademarks of Wavelink Corporation, Kirkland. RAM® and RAM Mount™ are both trademarks of National Products Inc., 1205 S. Orr Street, Seattle, WA 98108. All other brand or product names are trademarks or registered trademarks of their respective companies or organizations. When this manual is in PDF format: “Acrobat® Reader® Copyright © 2007 Adobe Systems Incorporated. All rights reserved. Adobe®, the Adobe logo, Acrobat®, and the Acrobat logo are registered trademarks of Adobe Systems Incorporated.” applies. The user is strongly encouraged to read Appendix B, Regulatory Notices and Safety Information. Important safety cautions, warnings and regulatory information is contained in Appendix B. Important: This symbol is placed on the product to remind users to dispose of Waste Electrical and Electronic Equipment (WEEE) appropriately, per Directive 2002-96-EC. In most areas, this product can be recycled, reclaimed and re-used when properly discarded. Do not discard labeled units with trash. For information about proper disposal, contact LXE through your local sales representative, or visit www lxe com. For Review - Preliminary - Draft 01 - Not for distribution Table of Contents INTRODUCTION Overview.................................................................................................................................... 1 MX8 Features .......................................................................................................................................... 2 Important Battery Information................................................................................................................. 3 Document Conventions ........................................................................................................................... 4 Environmental Specifications .................................................................................................................. 4 Laser Warnings and Labels ..................................................................................................... 5 Components.............................................................................................................................. 6 Front View ............................................................................................................................................... 6 Back View ............................................................................................................................................... 7 Scanner / Imager Aperture....................................................................................................................... 8 Trigger Handle......................................................................................................................................... 8 Handstrap................................................................................................................................................. 9 I/O Port and Cables................................................................................................................................ 10 MX8 AC Adapter .................................................................................................................................. 11 QUICK START 13 In Brief . . . ............................................................................................................................... 13 Troubleshooting..................................................................................................................................... 14 Related Manuals for Startup .................................................................................................................. 14 Inserting Fully Charged Battery ............................................................................................ 15 Checking Battery Status ........................................................................................................ 15 About Lithium-Polymer Batteries ......................................................................................................... 16 Tapping the Power Key .......................................................................................................... 16 Tapping the Touchscreen with a Stylus ............................................................................... 17 Keypad Shortcuts................................................................................................................................... 17 Calibrating the Touchscreen ................................................................................................. 18 Set Time Zone (Optional) ....................................................................................................... 18 Entering the AppLock Activation Key .................................................................................. 19 Hotkey (Activation Hotkey) .................................................................................................................. 19 Touch ..................................................................................................................................................... 19 Optional Accessory Installation ............................................................................................ 20 Attaching Handstrap (Optional)............................................................................................................. 20 Connecting an External Power Supply (Optional)................................................................................. 21 Putting it all together … ..................................................................................................................... 21 Assembling the 5V AC Power Adapter .............................................................................................. 21 Connecting the Multipurpose USB / Power Cable.............................................................................. 22 Connecting the Multipurpose RS-232 / Power Cable ......................................................................... 22 Connecting the Audio Cable and a Headset........................................................................................ 23 Adjust Microphone and Secure the Cable ........................................................................................ 23 Using the 32-Key Numeric-Alpha Keypad ............................................................................ 24 Entering Data .......................................................................................................................... 25 Using the Keypad .................................................................................................................................. 25 E-EQ-MX8OGWW-A MX8 User’s Guide For Review - Preliminary - Draft 01 - Not for distribution ii Table of Contents Using the Input Panel or Virtual Keyboard ........................................................................................... 25 Using the Stylus..................................................................................................................................... 26 Using the Integrated Barcode Scanner or Imager .................................................................................. 27 Barcode Scanner ................................................................................................................................. 27 2D Imager ........................................................................................................................................... 27 Scan Status LED ................................................................................................................................. 28 Tethered Scanners.................................................................................................................................. 28 Bluetooth Scanners and Printers ............................................................................................................ 28 Voice Data ............................................................................................................................................. 28 Bluetooth Devices .................................................................................................................. 29 Getting Help ............................................................................................................................ 30 Manuals ................................................................................................................................................. 30 Accessories – please verify.................................................................................................................... 30 THE MX8 HAND HELD COMPUTER 33 Reboot Sequence ................................................................................................................... 33 Warm Reset ........................................................................................................................................... 33 Cold Reset.............................................................................................................................................. 33 Saving Changes to the Registry – process still true?......................................................... 33 Touchscreen Display ............................................................................................................. 34 Cleaning the Glass Display/Beam Aperture .......................................................................................... 34 Applying the Protective Film to the Display ......................................................................................... 34 Adjusting the Display Backlight............................................................................................ 35 Set the Display Backlight Timer............................................................................................................ 35 Setting the Power Schemes Timers...................................................................................... 36 Battery Power Scheme........................................................................................................................... 36 AC Power Scheme................................................................................................................................. 36 Setting The Audio Speaker Volume ...................................................................................... 37 Using the Keypad .................................................................................................................................. 37 Using the Touchscreen .......................................................................................................................... 37 The Keypad ............................................................................................................................. 38 LED Indicators....................................................................................................................................... 38 System Status ...................................................................................................................................... 38 Scan Status .......................................................................................................................................... 39 Alpha Mode......................................................................................................................................... 39 Standard Keys........................................................................................................................................ 39 Function Keys........................................................................................................................................ 40 Sticky Keys ......................................................................................................................................... 40 Ctrl (Control key) ............................................................................................................................. 40 Alt (Alternate key)............................................................................................................................ 40 Shft (Shift key) ................................................................................................................................. 40 Orange and Blue Keys...................................................................................................................... 40 CapsLock Mode Function ................................................................................................................... 41 Batteries .................................................................................................................................. 42 Main Battery .......................................................................................................................................... 42 Backup Battery ...................................................................................................................................... 43 Battery Hotswapping ............................................................................................................................. 43 MX8 Battery Multi-Charger .................................................................................................... 44 Charge a Main Battery Pack .................................................................................................................. 44 Passive Vehicle Mount Cradle............................................................................................... 45 MX8 User’s Guide E-EQ-MX8OGWW-A For Review - Preliminary - Draft 01 - Not for distribution Table of Contents iii Cradle Assembly Components .............................................................................................................. 46 U-Bracket ............................................................................................................................................ 46 U-Bracket Footprint.......................................................................................................................... 46 RAM Ball and Cylinder ...................................................................................................................... 47 RAM Assembly Footprint ................................................................................................................ 48 How to Install the Cradle U-Bracket ..................................................................................................... 49 How To Install the RAM Bracket.......................................................................................................... 51 APPENDIX A KEY MAPS 55 Introduction............................................................................................................................. 55 32-Key Numeric-Alpha Keypad ............................................................................................. 55 APPENDIX B REGULATORY NOTICES AND SAFETY INFORMATION 61 MX8 Approvals/Standards ..................................................................................................... 62 INDEX E-EQ-MX8OGWW-A 69 MX8 User’s Guide iv Table of Contents For Review - Preliminary - Draft 01 - Not for distribution Illustrations Figure 1 CDRH / IEC 825 Caution Label Location – MX8, Back ................................................................... 5 Figure 2 Caution Label – Class 2 Laser Scanner .............................................................................................. 5 Figure 3 Front of MX8...................................................................................................................................... 6 Figure 4 Back.................................................................................................................................................... 7 Figure 5 Beam Aperture.................................................................................................................................... 8 Figure 6 Trigger Handle (Optional) .................................................................................................................. 8 Figure 7 Handstrap (Optional) .......................................................................................................................... 9 Figure 8 I/O Port and Cables........................................................................................................................... 10 Figure 9 5V AC Adapter - Assembled ............................................................................................................ 11 Figure 10 MX8 Cabling Options..................................................................................................................... 12 Figure 11 MX8 Desktop ................................................................................................................................. 13 Figure 12 Lithium Polymer Battery Pack ....................................................................................................... 15 Figure 13 Power Key Location ....................................................................................................................... 16 Figure 14 Touchscreen Recalibration ............................................................................................................. 18 Figure 15 Attaching the Handstrap ................................................................................................................. 20 Figure 16 USB – MX8 – Power Assembly ..................................................................................................... 21 Figure 17 AC/DC 5V External Power Supply ................................................................................................ 21 Figure 18 Connect the USB / Power Cable to the MX8 Port .......................................................................... 22 Figure 19 Connect the RS-232 / Power Cable to the MX8 Port...................................................................... 22 Figure 20 Audio Cable and Headset ............................................................................................................... 23 Figure 21 The 32-Key Keypad........................................................................................................................ 24 Figure 22 Input Panel / Virtual Keyboard....................................................................................................... 25 Figure 23 Laser Scanner Beam on Linear Barcode......................................................................................... 27 Figure 24 Imager Bracketed Crosshair Target on 2D Barcode ....................................................................... 27 Figure 25 Scan Status LED ............................................................................................................................. 28 Figure 26 Touchscreen Display ...................................................................................................................... 34 Figure 27 Setting the Display Backlight Timer............................................................................................... 35 Figure 28 Volume & Sounds Properties ......................................................................................................... 37 Figure 29 The 32-key Keypad........................................................................................................................ 38 Figure 30 Lithium Polymer Battery Pack ....................................................................................................... 42 Figure 31 MX8 Multi-Charger / Analyzer ...................................................................................................... 44 Figure 32 Insert Battery Pack in Charging Pocket .......................................................................................... 44 Figure 33 Passive Vehicle Mount Cradle and U-Bracket ............................................................................... 46 Figure 34 Bracket Mounting Footprint ............................................................................................................ 46 Figure 35 Passive Vehicle Mount Cradle / RAM Ball Assembly ................................................................... 47 Figure 36 RAM Bracket Components............................................................................................................. 47 Figure 37 RAM Assembly Footprint .............................................................................................................. 48 Figure 38 Install Cradle U-Bracket ................................................................................................................. 49 Figure 39 Install RAM Bracket Assembly ...................................................................................................... 51 MX8 User’s Guide E-EQ-MX8OGWW-A For Review - Preliminary - Draft 01 - Not for distribution Introduction Overview The LXE® MX8 is a rugged, portable, hand-held Microsoft® Windows® CE 5.0 equipped mobile computer capable of wireless data communications. The mobile device can transmit information using an 802.11 network card and it can store information for later transmission through an RS232 or USB port. The mobile device is vertically oriented and features backlighting for the display. The touchscreen display supports graphic features and Windows icons that the Windows CE 5.0 operating system supports. Keypads are available in 32-key numeric-alpha versions. This device is a Windows CE 5.0 compatible computer that can be scaled from a limited function batch computer to an integrated RF scanning computer. A trigger handle is available as an accessory. The stylus attached to the handstrap is used to assist in entering data and configuring the mobile device. Protective film for the touchscreen is available as an accessory. The MX8 is powered by a 3000 mAh Lithium-Polymer main battery pack and an internal Ni-MH backup battery. Important • • E-EQ-MX8OGWW-A If the mobile device has AppLock installed, please refer to the MX8 Reference Guide, Chapter 6 – AppLock for setup and processing. Wireless configuration and security parameters are described in detail in the MX8 Reference Guide, Chapter 5 – Wireless Network Configuration. MX8 User’s Guide 2 Overview MX8 Features The appropriate wireless utility for your device configuration has been pre-installed by LXE. For Review - Preliminary - Draft 01 - Not for distribution The desktop will display a Summit Client Utility icon for 802.11 wireless configuration and security. Summit Optional? LXE 802.11 b/g Radio No Summit® Client Utility No LXE Bluetooth Printers and Scanners Yes 520MHz No 128MB RAM No 128MB Flash No SE955 Laser Scanner Yes EV-15 Linear Imager Yes 5380SF 2D Imager Yes CE 5.0 No Voice Yes RFTerm® Yes JAVA® Yes AppLock Yes The MX8 does not have a Bluetooth managed LED. MX8 User’s Guide E-EQ-MX8OGWW-A Overview Important Battery Information For Review - Preliminary - Draft 01 - Not for distribution Note: Tap • • • • This mobile device’s backup battery maintains it’s charge by drawing power from the main battery pack. Always store unused devices with a fully charged main battery pack installed. LXE recommends an in-use mobile device be frequently connected to an external power source to maintain optimum power levels in the main battery pack and the backup battery. When the backup battery and main battery pack are dead, the mobile device reverts to the last saved setup defaults when a fully charged main battery pack is installed and the device is powered On again. | Settings | Control Panel | Battery tab. Until the main battery and backup battery are completely depleted, the MX8 is always drawing power from the batteries (On). New batteries must be fully charged prior to use. Whenever possible, use the AC power adapter with the MX8 to conserve the main battery and recharge the backup battery. Ni-MH backup battery replacement must be performed by qualified service personnel. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. ATTENTION E-EQ-MX8OGWW-A II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type equivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. MX8 User’s Guide 4 Overview Document Conventions For Review - Preliminary - Draft 01 - Not for distribution ALL CAPS All caps are used to represent disk directories, file names, and application names. Menu | Choice Rather than use the phrase “choose the Save command from the File menu”, this guide uses the convention “choose File | Save”. “Quotes” or Italics Indicates the title of a book, chapter or a section within a chapter (for example, “Document Conventions” and Document Conventions). Indicates a key on the keypad (for example,). Indicates a reference to other documentation. ATTENTION Keyword that indicates vital or pivotal information to follow. Attention symbol that indicates vital or pivotal information to follow. Also, when marked on product, means to refer to the user’s guide. International fuse replacement symbol. When marked on the product, the label includes fuse ratings in volts (v) and amperes (a) for the product. Note: Keyword that indicates immediately relevant information. CAUTION Keyword that indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. WARNING Keyword that indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. DANGER Keyword that indicates a imminent hazardous situation which, if not avoided, will result in death or serious injury. Environmental Specifications Operating Temperature 14°F to 122°F (-10°C to 50°C) [non-condensing] Storage Temperature -4°F to 158°F (-20°C to 70°C) [non-condensing] Water and Dust IEC 60529 compliant to IP54 Operating Humidity 5% to 90% non-condensing at 104°F (40°C) Vibration Based on MIL Std 810D ESD 8 kV air, 4kV contact Bluetooth Range 32.8 feet (10 meters) Direct line of sight only. MX8 User’s Guide E-EQ-MX8OGWW-A Laser Warnings and Labels For Review - Preliminary - Draft 01 - Not for distribution Laser Warnings and Labels • • • • Caution: Do not look into the laser’s lens. Do not stare directly into the laser beam. Do not remove the laser caution labels from the MX8. Do not connect the laser barcode aperture to any other device. The laser barcode aperture is certified for use with the MX8 only. Laser radiation when open. Please read the caution labels. Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Figure 1 CDRH / IEC 825 Caution Label Location – MX8, Back E-EQ-MX8OGWW-A Figure 2 Caution Label – Class 2 Laser Scanner MX8 User’s Guide 6 Components Components For Review - Preliminary - Draft 01 - Not for distribution Front View Figure 3 Front of MX8 Imager/Scanner Aperture Speaker System Status LED Scan Button Orange Key (Sticky Key) Blue Key (Sticky Key) Scan Status LED Cable Port On / Off Button 10 Alpha Mode LED Diamond Number Keys MX8 User’s Guide E-EQ-MX8OGWW-A Components For Review - Preliminary - Draft 01 - Not for distribution Back View Figure 4 Back Note: E-EQ-MX8OGWW-A Imager/Scanner Aperture Trigger Handle Attach Points and Handstrap Retainer Bracket Attach Points Main Battery Battery Fastener Cable Ports (I/O Port) The touch screen stylus is tethered to the handstrap or the trigger handle. MX8 User’s Guide 8 Components Scanner / Imager Aperture For Review - Preliminary - Draft 01 - Not for distribution CAUTION: Never stare directly into the beam aperture. Read the previous section Laser Warnings and Labels before using the scanner/imager. Figure 5 Beam Aperture Identify the type of integrated imager or laser scanner installed in the MX8 by looking at the type of plastic lens covering the Beam aperture. • • • • The No-Scanner option has an opaque lens protecting the MX8 internal components. The SE955 laser barcode scanner has a red lens protecting the laser engine. The EV-15 integrated imager has a clear lens protecting the imager engine. The 5380SF 2D imager has an opaque lens protecting the imager engine. Trigger Handle Figure 6 Trigger Handle (Optional) Note: Scan Aperture Trigger Handle Tether Attach Point Either the trigger handle is attached to the MX8 or the handstrap is attached, not both. LXE recommends that, in the absence of a trigger handle, the handstrap be used at all times. The stylus is tethered to the handstrap or the trigger handle. LXE pre-installs the trigger handle, if ordered. Refer to the MX8 Reference Guide for Trigger Handle installation instruction. MX8 User’s Guide E-EQ-MX8OGWW-A Components For Review - Preliminary - Draft 01 - Not for distribution Handstrap Figure 7 Handstrap (Optional) Note: E-EQ-MX8OGWW-A Handstrap Retainer Bracket Handstrap Handstrap Clip Either the trigger handle is attached to the MX8 or the handstrap is attached, not both. LXE recommends that, in the absence of a trigger handle, the handstrap be used at all times. The stylus is tethered to the handstrap or the trigger handle. LXE pre-installs the handstrap when the MX8 is purchased without a trigger handle. MX8 User’s Guide 10 Components I/O Port and Cables For Review - Preliminary - Draft 01 - Not for distribution Note: There is no IR port on the MX8. Tethered scanners are not supported on the MX8. Figure 8 I/O Port and Cables Cable: Multipurpose RS-232 and Power MX8A055MULTICBLDA9F Cable: Multipurpose USB and Power MX8A052MULTICBLUSB Adapter/Cable : Audio MX8A060ADPTCBLVOICE MX8 User’s Guide E-EQ-MX8OGWW-A Components 11 MX8 AC Adapter For Review - Preliminary - Draft 01 - Not for distribution need pic need pic AC Adapter AC Power Cable Figure 9 5V AC Adapter - Assembled The LXE-approved AC Power Adapter is only intended for use in a 25°C (77°F) maximum ambient temperature environment. E-EQ-MX8OGWW-A MX8 User’s Guide For Review - Preliminary - Draft 01 - Not for distribution 12 Components Note: Tethered scanners connected to the MX8 I/O port are not supported by LXE. Figure 10 MX8 Cabling Options MX8 User’s Guide E-EQ-MX8OGWW-A Quick Start For Review - Preliminary - Draft 01 - Not for distribution In Brief . . . Note: When your mobile device is pre-configured, the client, keypad and scan aperture configurations are assembled by LXE to your specifications. The desktop will display a Summit Client Utility icon. This section’s instructions are based on the assumption that your new device is pre-configured and requires only accessory installation (e.g. stylus) and a power source. LXE recommends that installation or removal of accessories be performed on a clean, well-lit surface. When necessary, protect the work surface, the mobile device, and components from electrostatic discharge. In general, the sequence of events is: 1. 2. 3. 4. 5. 6. Insert a fully charged battery. (Always put a fully charged battery in the mobile device at the beginning of the shift or workday.) Connect an external power source to the unit (if available). If the screen does not automatically display, tap the Power key. Calibrate the touchscreen. A white screen will appear during the boot process until all CAB files and applications are loaded and installed. Radio setup screens may appear and disappear while files are loading. After all files are loaded and the Microsoft Windows CE Desktop is displayed, adjust audio volume and other parameters if desired. If needed, change the Time and Date from it’s default value by tapping the Panel | Date/Time icon. | Settings | Control Figure 11 MX8 Desktop E-EQ-MX8OGWW-A MX8 User’s Guide 14 In Brief . . . For Review - Preliminary - Draft 01 - Not for distribution Troubleshooting Can’t calibrate the touch screen, change the date/time or adjust the volume. AppLock is installed and running on the mobile device. AppLock restricts User access to running programs. Changes or modifications require Administrator access. Refer to AppLock in the MX8 Reference Guide for setup and processing information. RFterm opens and runs upon each cold reset and warm reset. Tap File | Exit to close the RFTerm application. RFTerm opens and runs by default after every reset. The MX8 seems to lockup as soon as it is warm booted. There may be small delays while the wireless client connects to the network, authorization for Voxware-enabled applications complete, Wavelink Avalanche management of the MX8 startup completes, and Bluetooth relationships establish or re-establish.. Related Manuals for Startup Integrated Scanner Programming Guide – contains programming barcodes used when setting up integrated scan engines. • • • SE955 scanner barcode reading parameters, refer to Chapter 2 in the Integrated Scanner Programming Guide. Intermec EV-15 linear imager, refer to Chapter 3 in the Integrated Scanner Programming Guide. 5380SF 2D imager, refer to Chapter 4 in the Integrated Scanner Programming Guide. MX8 Reference Guide – contains instruction, technical and troubleshooting information for software and hardware functions. MX8 Multicharger User’s Guide – contains user, technical and troubleshooting information for the MX8 battery multi-charger. MX8 User’s Guide E-EQ-MX8OGWW-A Inserting Fully Charged Battery 15 Inserting Fully Charged Battery CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. For Review - Preliminary - Draft 01 - Not for distribution ATTENTION II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type equivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. Press the Power key after the battery is inserted into the MX8. Note: On first use the MX8 batteries should be charged with an external power source (i.e. AC Adapter) – 5 hours for the main battery and 7 hours for the backup battery. New main battery packs alone must be charged prior to first use – this process takes up to five hours in an LXE Multi-Charger. Figure 12 Lithium Polymer Battery Pack The MX8 Battery Compartment is located at the bottom of the back of the computer. The main battery functions as the battery well cover. Place the battery in the battery well, making sure the tab on the bottom of the battery pack fits into the slot at the bottom end of the battery well. Push the battery down into the battery well until the tab clicks into place and the battery pack is secure in the battery well. The backup battery is trickle-charged by the main battery. Whenever possible, use the AC power adapter with the MX8 to conserve the main battery and charge the backup battery. The Status LED indicates battery condition. It is steady red when the main battery is Low. When the battery has sufficient energy the Status LED is unlit. The Battery control panel displays main and backup battery charging and power status ( | Settings | Control Panel | Battery). Checking Battery Status Tap the | Settings | Control Panel | Battery icon. Main battery level, backup battery level, status and other details are displayed. E-EQ-MX8OGWW-A MX8 User’s Guide 16 Tapping the Power Key About Lithium-Polymer Batteries For Review - Preliminary - Draft 01 - Not for distribution Li-Polymer batteries (like all batteries) gradually lose their capacity over time (in a linear fashion) and never just stop working. This is important to remember – the MX8 is always ‘on’ even when | Settings | in the Suspend state and draws power from the batteries at all times. Tap the Control Panel | Power tab to check the battery status and power reading. The following chart is an approximation. Actual battery capacity varies based on usage, ambient temperature and peripherals drawing power from the MX8: 100% capacity 80% capacity 2800 mAh minimum 2280 mAh minimum Deciding when to put a fully charged main battery pack in the MX8 is difficult to quantify because it is very application specific. 2000 mAh may be the cutoff for one customer who uses the mobile device frequently, while 1500 mAh may be perfectly fine for a customer who occasionally uses the mobile device. You need to determine the point at which battery life becomes unacceptable for your business practices and replace the main battery pack before that point. Tapping the Power Key Note: Refer to the section titled Power Modes in the MX8 Reference Guide for information relating to the power states of the MX8. Important: Until the main battery and backup battery are completely depleted, the MX8 is always drawing power from the batteries (On). The Power key is located at the bottom of the keypad. When a battery is inserted in the MX8 for the first time press the Power key. Tapping the Power key places the MX8 immediately in Suspend mode. Tapping the Power key again immediately returns the MX8 from Suspend. or Tap | Suspend. Power Key Power Key Location Figure 13 Power Key Location See Also: LED Indicators and System Status LED later in this guide. See Also: Reboot Sequence in MX8 Hand Held Computer for reboot options and instruction. MX8 User’s Guide E-EQ-MX8OGWW-A Tapping the Touchscreen with a Stylus 17 Tapping the Touchscreen with a Stylus For Review - Preliminary - Draft 01 - Not for distribution Note: Always use the point of the stylus for tapping or making strokes on the touchscreen. Never use an actual pen, pencil, sharp or abrasive object to write on the touchscreen. Hold the stylus as if it were a pen or pencil. Touch an element on the screen with the tip of the stylus then remove the stylus from the screen. Place the stylus into the stylus holder when the stylus is not in use. Like using a mouse to left-click icons on a desktop computer screen, using the stylus to tap icons on the touchscreen is the basic action that can: • • • • • • • Note: Open applications Choose menu commands Select options in dialog boxes or drop-down boxes Drag the slider in a scroll bar Select text by dragging the stylus across the text Place the cursor in a text box prior to typing in data or retrieving data using the Scan button or an input/output device connected to the serial port. A mouse right-click is performed by holding the stylus down on the touchscreen. A circle of dots appear and then the right-click operation can be performed. See note. A “right mouse click” function must be programmed by the customer to accept a Tap and Hold function. An application can choose to interpret this function as a right mouse click. LXE does not support non-LXE application programming. Keypad Shortcuts Use keyboard shortcuts instead of the stylus: • • • • Press and an key to select a file. Once you’ve selected a file, press to open the file or press then press to open its Properties dialog. Press to delete a file. To force the Start menu to display, pressand release, press and release, then press (the Alt key). See the section titled Accessories for the stylus replacement kit part number. E-EQ-MX8OGWW-A MX8 User’s Guide 18 Calibrating the Touchscreen Calibrating the Touchscreen For Review - Preliminary - Draft 01 - Not for distribution If the touchscreen is not responding properly to stylus taps, you may need to recalibrate the touchscreen. Recalibration involves tapping the center of a target. If you miss the center, keep the stylus on the screen, slide it over the target’s center, and then lift the stylus. If the touchscreen is not accepting taps or needs recalibration, press + + to force the Start Menu to appear. To recalibrate the screen, select | Settings | Control Panel | Stylus | Calibration tab. To begin, tap the Recalibrate button on the screen with the stylus. Figure 14 Touchscreen Recalibration Follow the instructions on the screen and press the Enter key to save the new calibration settings or press Esc to cancel or quit. Set Time Zone (Optional) Note: The first time it is powered up, or the device returns from a Cold Reset, the MX8 resets the Time Zone to the factory default values (GMT-05:00 Eastern Time). To set the Time Zone, tap the Start | Settings | Control Panel | Date/Time icon. Select the physical time zone. Enable the checkbox next to “Automatically adjust clock for daylight saving” if applicable. If required, adjust the time and calendar date and tap the Apply button. Tap the OK button when you are finished or the X button to ignore any changes. MX8 User’s Guide E-EQ-MX8OGWW-A Entering the AppLock Activation Key 19 Entering the AppLock Activation Key For Review - Preliminary - Draft 01 - Not for distribution Hotkey (Activation Hotkey) If the mobile device uses LXE’s AppLock to allow the user to switch between applications, the default Activation key is + . The key sequence switches the focus between one application and another. Data entry affects the application running in the foreground only. Note that the system administrator may have assigned a different key sequence to use when switching applications. Touch Note: The touch panel must be enabled. Tap the Switchpad taskbar icon to place the popup menu on screen. Tap one of the application names in the popup menu. The selected application is brought to the foreground while the other application continues to run in the background. Stylus taps affect the application running in the foreground only. E-EQ-MX8OGWW-A MX8 User’s Guide 20 Optional Accessory Installation Optional Accessory Installation For Review - Preliminary - Draft 01 - Not for distribution Attaching Handstrap (Optional) Note: Either the trigger handle is attached to the MX8 or the handstrap is attached, not both. LXE recommends that, in the absence of a trigger handle, the handstrap be used at all times. LXE pre-installs the handstrap on devices that are purchased without a trigger handle. Refer to the MX8 Reference Guide for instructions on installing the Trigger Handle (a torque wrench will be required). Once installed, the handstrap provides a means for the user to secure the computer to their hand. It is adjustable to fit practically any size hand and does not interfere with the multipurpose cable, if connected, when the mobile device is in a cradle. Figure 15 Attaching the Handstrap Handstrap Retainer Bracket Handstrap Handstrap Clip Tool Required: #1 Phillips Screwdriver (not supplied by LXE) Installation 1. 2. 3. 4. 5. 6. Place the MX8, with the screen facing down, on a flat stable surface. Attach the handstrap retainer bracket to the MX8 with the screws provided. Slip the Handstrap Clip into the bracket at the base of the MX8. Making sure the closed loop fastener surfaces on the handstrap are facing up, slide the strap through the pin in the retainer bracket and the clip. Fold each end of the the strap over so that the closed loop fastener surfaces mate evenly. Test the strap's connection making sure the MX8 is securely connected to each end of the strap connectors. Check the closed loop fastener, retainer bracket and clip connections frequently. If they have loosened, they must be tightened before the MX8 is placed into service again. If the handstrap gets worn or damaged, it must be replaced. MX8 User’s Guide E-EQ-MX8OGWW-A Optional Accessory Installation 21 Connecting an External Power Supply (Optional) For Review - Preliminary - Draft 01 - Not for distribution The MX8 receives AC/DC power from the AC/DC 5V Power Supply. The MX8 external power connection is part of the RS-232 cable assembly and the USB cable assembly. Putting it all together … . Figure 16 USB – MX8 – Power Assembly To apply external power to the MX8 follow the steps below in sequence. 1. Plug the 2 prong adapter cable end of the external power module into an AC power source (e.g. wall outlet). 2. Squeeze the sides of the power connector and push the power cable connector into the MX8 I/O port until it clicks. The click means the connector is seated firmly. The System LED above the Scan key illuminates when the MX8 is charging the main battery pack using external power through the power cable. The backup battery is always being trickle charged by the main battery pack. Whenever possible, use the AC power adapter with the MX8 to conserve the main battery power and maintain a charge in the backup battery. Assembling the 5V AC Power Adapter The LXE-approved AC Power Adapter is only intended for use in a 25°C (77°F) maximum ambient temperature environment. If the AC power cable is not included with the AC Adapter, please contact your LXE representative for assistance. need new pic Figure 17 AC/DC 5V External Power Supply Plug the 2-prong cable into an AC wall outlet. Firmly press the female end of the power cable into the male connector on the power adapter. AC power is now being supplied to the power adapter. See Accessories for the LXE part number for the AC Power Adapter to use with the MX8. E-EQ-MX8OGWW-A MX8 User’s Guide 22 Optional Accessory Installation For Review - Preliminary - Draft 01 - Not for distribution Connecting the Multipurpose USB / Power Cable Figure 18 Connect the USB / Power Cable to the MX8 Port Connector A Squeeze the clips on the connector cable to open the catches in the connector assembly. Firmly press Connector A into the connector at the base of the MX8. Release the clips in the connector cable. Test the connection for stability before connecting to USB Connector B Firmly push the power cable connector pin into connector B. Plug the 2-prong cable into an AC wall outlet. Connector C Insert the USB Type A plug into an appropriate USB port on a desktop/laptop computer for ActiveSync communication. Connecting the Multipurpose RS-232 / Power Cable Figure 19 Connect the RS-232 / Power Cable to the MX8 Port Connector A Squeeze the clips on the connector cable to open the catches in the connector assembly. Firmly press Connector A into the connector at the base of the MX8. Release the clips in the connector cable. Test the connection for stability before connecting the B or C connector. Connector B Firmly push the power cable connector pin into connector. Plug the 2-prong cable into an AC wall outlet. Connector C Align the RS-232 serial cable end carefully to an appropriate serial port on a desktop/laptop computer for ActiveSync communication. Press the ends together and hand tighten the screws on either side of the serial cable until the MX8 is securely connected to the serial device. MX8 User’s Guide E-EQ-MX8OGWW-A Optional Accessory Installation 23 Connecting the Audio Cable and a Headset See section titled Set the Audio Speaker Volume. Use the Control Panel Mixer applet to set up the mono headphone. The Summit Client supports mono only. For Review - Preliminary - Draft 01 - Not for distribution Note: The audio option draws power from the main battery. The headset consists of an earpiece, a microphone and an attached cable. The headset attaches to the audio cable which attaches to the MX8. Figure 20 Audio Cable and Headset Connector A Squeeze the clips on the connector cable to open the catches in the connector assembly. Firmly press Connector A into the connector at the base of the MX8. Release the clips in the connector cable. Test the connection for stability before continuing. Connector B (Optional) Firmly push the power cable connector pin into the MX8 connector. Plug the 2-prong cable into an AC wall outlet. Connector C Align Connector C and the headset quick connect cable end. Firmly push the cable ends together until they click and lock in place. Adjust Microphone and Secure the Cable Do not twist the microphone boom when adjusting the microphone. The microphone should be adjusted to be about two finger widths from your mouth. Make sure the microphone is pointed at your mouth. Note the small “Talk” label near the mouthpiece. Make sure the Talk label is in front of your mouth. The microphone cable can be routed over or under clothing. Under Clothing • • Leave the cable exposed only at the top of the collar. Be sure to leave a small loop of cable to allow movement of your head. Over Clothing • • • E-EQ-MX8OGWW-A Use clothing clips to hold the cable close to your body. Tuck the cable under the belt, but leave a small loop where it goes under the belt. Do not wear the cable on the front of your body. It may get in your way or get caught on protruding objects. MX8 User’s Guide 24 Using the 32-Key Numeric-Alpha Keypad For Review - Preliminary - Draft 01 - Not for distribution Using the 32-Key Numeric-Alpha Keypad System Status LED Speaker adjust icon Brightness adjust icon Diamond Keys (Mappable keys) Scan Button Enter Key Orange Key (Sticky Key) Blue Key (Sticky Key) On/Off Button 10 Scan Status LED Figure 21 The 32-Key Keypad • • • • When using a sequence of keys that require an alpha key, first press the Alph key. Use the Shft sticky key or the Caps key sequence (Blue+Tab) for upper case alphabetic characters. Pressing the Alph key forces “Alpha” mode for the 2,3,4,5,6,7,8, and 9 keys. The 1 and 0 keys continue to place a 1 and 0 into the text field. To create a combination of numbers and letters before pressing Enter, remember to tap the Alph key to toggle between Alpha and Numeric mode. When using a sequence of keys that do not include the Alph key but does include a sticky key, press the sticky key first then the rest of the key sequence. The keymaps (keypress sequences) are located in Appendix A – Key Maps. MX8 User’s Guide E-EQ-MX8OGWW-A Entering Data 25 Entering Data For Review - Preliminary - Draft 01 - Not for distribution You can enter data into the MX8 through several different methods. The scanner aperture provides barcode data entry, the I/O port is used to input/output data, and the keypad provides manual (or keyed) data entry. Mobile devices with a touchscreen use a stylus to input data, the I/O port and/or the keypad. An input panel (virtual keyboard) is available in applications that expect keyed input. Using the Keypad The keypad is used to manually input data that is not collected otherwise. Almost any function that a full sized computer keyboard can provide is duplicated on the MX8 keypad but it may take a few more keystrokes to accomplish a keyed task. Please refer to Appendix A – Key Maps for instruction on the specific keypresses to access all keypad functions. Almost every key has two or three different functions. The primary alpha or numeric character is printed on the key. The Orange or Blue keys are pressed when you want to use a “sticky” key function. For example, when you press a Blue or Orange key (the sticky key), then press the key that has the desired second-function key, the second-function key is the “active” key. The specific sticky character is printed above the corresponding key in either Orange or Blue. Using the Input Panel or Virtual Keyboard The virtual keyboard is always available when needed e.g. text field input. Tap the keyboard icon at the bottom of the screen to put the virtual keyboard on the display. Using the stylus: • • • Tap the Shift key to type one capital letter. Tap the CAPS key to type all capital letters. Tap the au key to access symbols. Figure 22 Input Panel / Virtual Keyboard Some applications do not automatically display the Input Panel. In this case, do the following to use the Input Panel: 1. Tap the Input Panel/Virtual Keyboard icon in the taskbar. 2. Select Keyboard from the menu. 3. Tap the data entry area on the display when you want to enter data using the Input Panel. E-EQ-MX8OGWW-A MX8 User’s Guide 26 Entering Data Using the Stylus For Review - Preliminary - Draft 01 - Not for distribution Note: This section is directed to the MX8 daily user. The assumption is that the mobile device has been configured and the touch panel calibrated by the System Administrator prior to releasing the MX8 for daily use. The touch screen should be calibrated before initial use. The stylus performs the same function as the mouse that is used to point to and click elements on a desktop computer. The stylus is used in the same manner as a mouse – single tap or double tap to select menu options, drag the stylus across text to select, hold the stylus down to activate slider bars, etcetera. Hold the stylus as if it were a pen or pencil. Touch an element on the screen with the tip of the stylus then remove the stylus from the screen. Place the stylus into the stylus holder when the stylus is not in use. The stylus can be used in conjunction with the keyboard and scanner and an input/output device connected to the serial port. • • • Note: MX8 User’s Guide Touch the stylus to the field of the data entry form to receive the next data feed. The cursor begins to flash in the field. The unit is ready to accept data from either the physical keypad, virtual keyboard, an input/output device connected to the serial port or the integrated scan aperture. Always use the point of the stylus for tapping or making strokes on the display. Never use an actual pen, pencil or sharp object to write on the touch screen. E-EQ-MX8OGWW-A Entering Data 27 Using the Integrated Barcode Scanner or Imager Use the integrated laser scanner to scan linear barcodes. Use the EV-15 integrated imager to scan 1D linear barcodes. For Review - Preliminary - Draft 01 - Not for distribution Use the 5380SF integrated imager to scan 2D barcodes. • • • Read all cautions, warnings and labels before using the laser scanner. Do not look into the laser’s lens. Do not stare directly into the laser beam. Barcode Scanner To scan with the integrated laser barcode reader, point the scan aperture towards a barcode and press the Scan button. You will see a red beam strike the barcode. Align the beam so that the barcode is centered within the beam. The laser beam must cross the entire barcode. Move the MX8 towards or away from the barcode so that the barcode takes up approximately two-thirds the width of the beam. There may be a tactile response combined with the Scan functions. Laser Correct Scan Incorrect Scan Incorrect Scan Figure 23 Laser Scanner Beam on Linear Barcode 2D Imager Figure 24 Imager Bracketed Crosshair Target on 2D Barcode To scan with the integrated imager, point the scan aperture towards a 2D barcode and press the Scan button. You will see a bracketed crosshair strike the barcode. Align the brackets so that the center of the barcode is covered by the crosshair. Move the MX8 towards or away from the barcode until a response is received by the MX8 (beep, tactile response, etc) or the bracketed crosshair times out and disappears. E-EQ-MX8OGWW-A MX8 User’s Guide 28 Entering Data For Review - Preliminary - Draft 01 - Not for distribution Scan Status LED Figure 25 Scan Status LED The Scan Status LED (oval shaped LED below keypad) turns red when the laser beam is on. Following a barcode scan and read the Scan Status LED turns green for two seconds and the MX8 beeps or vibrates, indicating a successful scan. If the scan was unsuccessful, the Scan Status LED turns off and a different beep sequence is heard. The laser engine and Scan Status LED automatically turn off after a successful read, or after the timer expires after an unsuccessful read. The scanner / imager is ready to scan again after the Scan key (or trigger on the handle if installed) is released, or after the Scan Status LED turns off following a successful scan. The Scan Status LED turns amber when scanner/imager programming changes, if any, are being saved. When the LED is off, the MX8 is ready to scan again. Tethered Scanners Tethered scanners cabled to the MX8 I/O port are not supported by LXE. Bluetooth Scanners and Printers Bluetooth scanners are paired to the MX8 wirelessly using the MX8 Bluetooth wireless client. Only LXE Bluetooth scanners and LXE Bluetooth printers are supported by LXE. See Accessories. Voice Data Data is entered into the MX8 by speaking into the headset’s microphone when prompted. Please contact your System Administrator if assistance is needed with the voice software. MX8 User’s Guide E-EQ-MX8OGWW-A Bluetooth Devices 29 For Review - Preliminary - Draft 01 - Not for distribution Bluetooth Devices Assumption: The System Administrator has Discovered and Paired targeted Bluetooth devices for each MX8. The System Administrator has also enabled / disabled Bluetooth settings and assigned a Computer Friendly Name for each MX8. See the MX8 Reference Guide for information and instruction on the MX8, Bluetooth control panel applet and supported LXE Bluetooth printers and scanners. The Bluetooth taskbar Icon state and Bluetooth scanner LED states change as Bluetooth devices are discovered, pair, connect and disconnect. There may be audible or visual signals as paired devices re-connect with the MX8. Non-LXE Bluetooth devices may be discovered but are inaccessible as they are filtered out on the Bluetooth Devices panel and are not displayed (see MX8 Reference Guide for details). Taskbar Icon Legend Bluetooth module is connected to one or more of the targeted Bluetooth device(s). MX8 is not connected to any Bluetooth device. MX8 is ready to connect with any Bluetooth device. MX8 is out of range of all paired Bluetooth device(s). Connection is inactive. Note: When an active paired device, not the MX8, enters Suspend Mode, is turned Off or leaves the MX8 Bluetooth scan range, the Bluetooth connection between the linked device and the MX8 is lost. There may be audible or visual signals as paired devices disconnect from the MX8. Notes: • • • • The MX8 does not have a Bluetooth managed LED. The LED on the Bluetooth scanner illuminates during a scanning operation; the Scan LED on the MX8 does not illuminate. Barcode data captured by the Bluetooth scanner is manipulated by the settings in the MX8 Scanner Properties control panel applet. Multiple beeps may be heard during a barcode scan using the Bluetooth scanner; beeps from the Bluetooth scanner as the barcode data is accepted/rejected, and other beeps from the MX8 during final barcode data manipulation. See Accessories for supported Bluetooth printers and scanners. AppLock, if installed, does not stop the end-user from using Bluetooth, nor does it stop authorized Bluetooth devices from pairing with the MX8 while AppLock is in control. E-EQ-MX8OGWW-A MX8 User’s Guide 30 Getting Help Getting Help For Review - Preliminary - Draft 01 - Not for distribution All LXE user guides are now available on one CD and they can also be viewed/downloaded from the LXE ServicePass website. Contact your LXE representative to obtain the LXE Manuals CD. You can also get help from LXE by calling the telephone numbers listed on the LXE Manuals CD, in the file titled Contacting LXE. This information is also available on the LXE website. Explanations of terms and acronyms used in this guide are located in the file titled LXE Technical Glossary on the LXE Manuals CD and the LXE ServicePass website. Manuals MX8 Reference Guide MX8 Multi-Charger / Analyzer User’s Guide LXEbook – MX8 User’s Guide (download to mobile device) RFTerm Reference Guide LXE Security Primer CE API Programmers Guide Integrated Scanner Programmers Guide Accessories – please verify Note: Items with a Green letter R in the second column are ROHS-compliant. Please contact your LXE representative when ordering ROHS-compliant items as the part number may have changed. Items without the letter R may have received ROHS-compliance after this guide was published. MX8 Main Battery, Lithium Polymer MX8A380BATT 4 Unit Main Battery Charger (US power cord) MX8A385CHGR5US 4 Unit Main Battery Charger (no power cord) MX8A386CHGR5WW MX8 Passive vehicle cradle. Does not support charging or communication. U-Bracket included. MX8A007VMCRADLE RAM mount kit for MX8 Vehicle Bracket. This kit does NOT include the Cradle. Attaches to U-Bracket. MX8A001RAMBRKT Replacement MX8 Hand Strap MX8A401HANDSTRAP Carry case for MX8 with no handle, includes shoulder strap MX8A402CASENHDL Carry case for MX8 with handle, includes shoulder strap MX8A403CASEHDL MX8 Voice Application case with belt MX8A404CASEVRNHDL Holster for MX8 with handle, belt NOT included MX8A405HOLSTERHDL MX8 Padded handle with rubber overmold and two finger trigger, includes wrist strap MX8A406HANDLE Holster for MX8 with no handle, belt not included MX8A407HOLSTERNHDL Black rubber protective boot MX8A488PROTBOOT Yellow rubber protective boot MX8A489PROTBOOTYEL Carry case for MX8 with Gearkeeper retractor MX8A408RETRACTORCASE MX8 User’s Guide E-EQ-MX8OGWW-A For Review - Preliminary - Draft 01 - Not for distribution Getting Help 31 Non-handle holster that fits MX8 with boot MX8A409HOLSTERWBOOT Holster belt 9200L67 MX8 Charge/Comm Interface Cable, USB Client for ActiveSync MX8A052MULTICBLUSB MX8 Charge/Comm Interface Cable, RS-232 Serial ActiveSync, D9 Female MX8A055MULTICBLDA9F AC/DC power supply with US power cord for use with MX8 Charge/Comm cables 9000A319PSACUS AC/DC power supply without power cord for use with MX8 Charge/Comm cables 9000A302PSACWW RS-232 Serial Adapter cable, 6in, for use with printers that provide their own source of power. MX8A058ADPTCBLPER MX8 Headset coiled adapter cable, includes quick disconnect headset connector. A headset is still required. MX8A060ADPTCBLVOICE MX8 Replacement Stylus , 10-pack MX8A584STYLUS Large tethered stylus which fit the MX8 carry cases, 5 pack 9000A507STYLUS CD with CE 5.0 API’s and LXE API’s with documentation for custom application development MX8A504CE50SDK Touch screen anti-glare anti-reflective protective film, 10 pack MX8A584PROTFILM VoxBrowser™ English & Americas VOXBROWSER ENG VoxBrowser™ Rest-of-the-World VOXBROWSER ROW Single ear, single headband, headset with noise canceling microphone, includes 5 replacement windscreens HX1A501SNGBHEADSET Single ear, dual headband, headset with noise canceling microphone, includes 5 replacement windscreens HX1A502DUALBHEADSET Dual ear, behind the head, headset with noise canceling microphone, includes 5 replacement windscreens HX1A503BTHHEADSET Replacement foam block for 502 dual band headsets, qty 1 HX1A504AHSBLOCKFOAM Replacement head yoke for dual band 502 headset, qty 1 HX1A505DUALYOKE Replacement head yoke for single band 501 headset, qty 1 HX1A506SINGLEYOKE Replacement windscreen for all headset microphones, 10 Pack HX1A508WINDSCREEN10 Replacement windscreen for all headset microphones, 50 Pack HX1A509WINDSCREEN50 Replacement foam ear piece cover for 501 and 502 headsets, 10 pack HX1A510FOAMEAR10 Replacement foam ear piece cover for 501 and 502 headsets, 50 pack HX1A511FOAMEAR50 E-EQ-MX8OGWW-A MX8 User’s Guide For Review - Preliminary - Draft 01 - Not for distribution 32 MX8 User’s Guide Getting Help E-EQ-MX8OGWW-A For Review - Preliminary - Draft 01 - Not for distribution The MX8 Hand Held Computer Reboot Sequence When the Windows CE desktop is displayed or an application begins, the power up (or reboot) sequence is complete. If you have previously saved your settings, they will be restored on reboot. Application changes are saved when OK is clicked on an application applet. Warm Reset There are two methods for the Warm Reset. 1. 2. Using the input panel, you can tap | Run and type WARMBOOT. Tap the OK button. Hold down the Power key and the Enter key until the screen blanks. Release the keys and the MX8 resets. Data not saved is lost. Cold Reset Important:-- Because of the extreme nature of the Cold Reset, LXE recommends that the Cold Reset be used only as an emergency procedure and the Warm Reset be used whenever necessary. There are two methods for the Cold Reset. 1. 2. | Run and type COLDBOOT.EXE. Tap the OK button to coldboot the MX8. The Tap default settings are restored when the device powers on again. Hold down the Scan key, Blue function key and the Power key until the screen blanks. Release the keys and the default settings are restored when the device powers on again. Calibrating the touchscreen will need to be performed when the cold boot process is complete. If needed, change the MX8 Time and Date from it’s factory default value by tapping the Settings | Control Panel | Date/Time icon. Saving Changes to the Registry – process still true? The MX8 saves the registry when you: • • Tap the | Run | and type Warmboot. Perform a Suspend / Resume function (by pressing the Pwr key and then pressing it again). The registry save process takes 5 – 10 seconds. The registry is automatically saved every 20 minutes. It is also saved every tenth time the registry settings are changed. Registry settings are changed when control panel applet (e.g. Date/Time) parameters are changed by the user and a warm boot was not performed afterward. When you tap | Run | and type Coldboot, factory default registry settings are loaded. All user changes and settings are lost. E-EQ-MX8OGWW-A MX8 User’s Guide 34 Touchscreen Display For Review - Preliminary - Draft 01 - Not for distribution Touchscreen Display Figure 26 Touchscreen Display The touchscreen display is an active color LCD unit capable of supporting VGA graphics modes. Display size is 240 x 320 pixels or ¼ VGA in portrait orientation. The covering is designed to resist stains. The touchscreen allows signature capture and touch input. A pen stylus is included with the handstrap and the trigger handle. The touchscreen responds to an actuation force (touch) of 4 oz. of pressure (or greater). The color display is optimized for indoor lighting. The display is black when the mobile device is in Suspend mode or when both batteries have expired and the unit is Off. See section titled Calibrating the Touchscreen in the Quick Start section for touchscreen calibration instruction. See the MX8 Reference Guide for full instruction. Cleaning the Glass Display/Beam Aperture Note: These instructions are for components made of glass. If there is a removable protective film sheet on the display screen, remove the film sheet before cleaning the screen. Keep fingers and rough or sharp objects away from the scan aperture and display. If the glass becomes soiled or smudged, clean only with a standard household cleaner such as Windex® without vinegar or use Isopropyl Alcohol. Do not use paper towels or harsh-chemical-based cleaning fluids since they may result in damage to the glass surface. Use a clean, damp, lint-free cloth. Do not scrub optical surfaces. If possible, clean only those areas which are soiled. Lint/particulates can be removed with clean, filtered canned air. Applying the Protective Film to the Display First, clean the display of fingerprints, lint particles, dust and smudges. Remove the protective film from its container. Remove any protective backing from the film sheet by lifting the backing from a corner of the film. Discard the backing. Apply the film to the screen starting at one side and smoothing it across the display. If air bubbles appear, raise the film slightly and continue smoothing the film across the display until it covers the glass surface of the display. If dust, lint or smudges are trapped between the protective film and the glass display, remove the protective film, clean the display and apply the protective film again. MX8 User’s Guide E-EQ-MX8OGWW-A Adjusting the Display Backlight 35 Adjusting the Display Backlight For Review - Preliminary - Draft 01 - Not for distribution Set the Display Backlight Timer Select | Settings | Control Panel | Display | Backlight tab. Change the parameter values and tap OK to save the changes. Figure 27 Setting the Display Backlight Timer The first option affects the mobile device when it is running on battery power only. The second option affects the device when it is running on external power (e.g. AC adapter). The default value for the battery power timer is 3 seconds. The default value for the external power timer is 2 minutes. The backlight will remain on all the time when both checkboxes are blank. The display backlight timer dims the backlight at the end of the specified time. E-EQ-MX8OGWW-A MX8 User’s Guide 36 Setting the Power Schemes Timers Setting the Power Schemes Timers For Review - Preliminary - Draft 01 - Not for distribution Note: Refer to the section titled Power Modes in the MX8 Reference Guide for information relating to the power states of the mobile device. Select | Settings | Control Panel | Power | Schemes tab. Change the parameter values and tap OK to save the changes. Battery Power Scheme Use this option when the device will be running on battery power only. Switch state to User Idle: Default is After 3 seconds Switch state to System Idle: Default is After 15 seconds Switch state to Suspend: Default is After 5 minutes AC Power Scheme Use this option when the device will be running on external power (e.g. AC adapter). Switch state to User Idle: Default is After 2 minute Switch state to System Idle: Default is After 2 minutes Switch state to Suspend: Default is After 5 minutes These mode timers are cumulative. The System Idle timer begins the countdown after the User Idle timer has expired and the Suspend timer begins the countdown after the System Idle timer has expired. When the User Idle timer is set to “Never”, the power scheme timers never place the device in User Idle, System Idle or Suspend modes (even when the device is idle). Because of the cumulative effect, and using the Battery Power Scheme Defaults listed above: • • • MX8 User’s Guide The backlight turns off after 3 seconds of no activity, The display turns off after 18 seconds of no activity (15sec + 3sec), And the device enters Suspend after 5 minutes and 18 seconds of no activity. E-EQ-MX8OGWW-A Setting The Audio Speaker Volume 37 Setting The Audio Speaker Volume For Review - Preliminary - Draft 01 - Not for distribution Note: An application may override the control of the speaker volume. Turning off sounds saves power and prolongs battery life. The speaker is located on the front of the device above the MX8 logo. The audio volume can be adjusted to a comfortable level for the listener. The volume is increased or decreased one step each time the volume key sequence is pressed. The device has an internal speaker and a jack for an external headset. Operational “beeps” are emitted from the speaker. Using the Keypad Note: Volume & Sounds (in Settings|Control Panel) must be enabled before the following key sequences will adjust the volume. To adjust speaker volume: • • • Tap the Orange key then the Scan key to enter Volume change mode. Use the Up Arrow and Down Arrow keys to adjust volume until the speaker volume is satisfactory. Press the Enter key to exit this mode. Using the Touchscreen Figure 28 Volume & Sounds Properties | Settings | Control Panel | Volume & Sounds | Volume tab. Change the volume setting and Tap tap OK to save the change. You can also select / deselect sounds for key clicks and screen taps and whether each is loud or soft. As the volume scrollbar is moved between Loud and Soft, the computer will emit a tone each time the volume increases or decreases in decibel range. E-EQ-MX8OGWW-A MX8 User’s Guide 38 The Keypad The Keypad For Review - Preliminary - Draft 01 - Not for distribution The keypad is installed and configured by LXE to your specifications. Figure 29 The 32-key Keypad See Appendix A – Key Maps for instruction on the specific keypresses to access all keypad functions. LED Indicators System Status The System Status LED is located at the top left of the keypad, above the Scan button. When the LED is . . . The Status is . . . Comment Replace the main battery with a fully charged main battery. Blinking Red Power Fail Or Connect the MX8 to external AC power. Low Battery Warning. Replace the main battery with a fully charged main battery. Steady Red Main Battery Low Or Connect the MX8 to external AC power. MX8 User’s Guide E-EQ-MX8OGWW-A The Keypad 39 When the LED is . . . The Status is . . . Comment Blinking Green Display Off No user intervention required. No Color Good No user intervention required. For Review - Preliminary - Draft 01 - Not for distribution Scan Status The Scan Status LED is located below the MX8 keypad. When the Scan Status LED is . . . The Status is . . . Steady Green Good Scan Steady Red Scan in Progress Amber ?? Scanner/imager programming changes are being saved. No Color Scanner/Imager ready for use. Alpha Mode The Alpha Mode LED is located beside the key on the 32-key keypad. When the Alph LED is . . . The Status is . . . Steady Green Device is in “Alpha” character input mode. No Color Device is in “Numeric” key input mode. Standard Keys See Also: Appendix A – Key Maps Scan The integrated scanner/imager scans only when the Scan button is pressed (or when the scan trigger is pressed on the optional trigger handle). Enter The Enter key is used to confirm a forms entry or to transmit information. How it is used is determined by the application running on the mobile device. Diamond The Diamond key(s) can be programmed to duplicate a single keypress (as defined by Windows CE) with the exception of the Shift, Alt and Ctrl key. Numeric The number keys are used to add numbers to data entry fields. Alpha The alpha keys are used to add letters and characters to data entry fields. Space The Spc key adds a space to the line of data on the display. This function is similar to a regular keyboard’s Spacebar. Note that the Spc key only stays active for one keystroke. E-EQ-MX8OGWW-A MX8 User’s Guide 40 The Keypad Function Keys Sticky Keys For Review - Preliminary - Draft 01 - Not for distribution The Sticky Key feature allows the user to activate multi-keypress combinations with one finger. Ctrl (Control key) A Control sticky keypress stays active until the Control key is pressed again. The Control key enables the control functions of the keypad. This function is similar to a regular keyboard’s Control key. Each time you need to use a Control function, you need to press the Ctrl key before pressing the desired key. Alt (Alternate key) An Alt sticky keypress stays active until the Alt key is pressed again. The Alt key enables the alternate functions of the keypad. This function is similar to a regular keyboard’s Alt key. Each time you need to use an alternate function, you need to press the Alt key before pressing the desired key. Shft (Shift key) A Shift keypress ends a sticky key function. The Shft key enables the shifted functions of the keypad. This function is similar to a regular keyboard’s Shift key. Note that the Shift key only stays active for one keystroke. Each time you need to use a Shifted function, you need to press the Shft key before pressing the desired key. When the Shft key is pressed the next key is determined by the major key legends, i.e., the alpha keys display lower case letters -- when CAPS is On alpha characters are capitalized. For example, when CAPS is On and the Shft key and the G key are pressed, a lower case g is displayed. Orange and Blue Keys The Orange and Blue keys are sticky keys that, when tapped, activate the second functions of the keypad. Printed above many keys are small characters, in either orange (on the left side of the key) or blue (on the right side of the key), that represent the second function of that key. Using the sticky key activates the second key function. Note that the blue and orange sticky keys only stay active for one keystroke. Each time you need to activate a second function you must press the Orange or Blue key. To cancel a sticky key function before pressing another key, press the same sticky key again. Orange Key Tap the Orange key to enter “orange” mode. Tap it again to cancel “orange” mode. If you were in “blue” mode before you pressed the Orange key, blue mode is cancelled and you enter Orange mode. Blue Key Tap the Blue key to enter “blue” mode. Tap it again to cancel “blue” mode. If you were in “orange” mode before you pressed the Blue key, orange mode is cancelled and you enter Blue mode. MX8 User’s Guide E-EQ-MX8OGWW-A The Keypad 41 CapsLock Mode Function For Review - Preliminary - Draft 01 - Not for distribution The CapsLock key sequence is Blue key then the key. This function is similar to a regular keyboard’s CapsLock key. Note that the CapsLock mode stays active until the CapsLock key sequence is pressed again. Each time you need to use a Caps function, you need to press the Caps key sequence first. To cancel a CapsLock function press the Caps key sequence again. Example: 2 B or Not 2 B To put the number 2 in a text entry field: Tap the <2> key once. To put a lowercase “b” in a text field: Tap the key, then tap the <2> key twice. To put an uppercase “B” in a text field: Tap the key, tap the key or the key, then tap the <2> key twice. To enter a string of letters in a text field, tap the key to toggle it On. It remains active until it is tapped again and toggled off. To enter a string of numbers in a text field, make sure the key is toggled off. E-EQ-MX8OGWW-A MX8 User’s Guide 42 Batteries Batteries For Review - Preliminary - Draft 01 - Not for distribution Note: New batteries must be charged prior to use. If the main battery and backup battery are depleted, the mobile device reverts to factory default values. Wireless configuration parameters will need to be re-entered after reverting to factory default values. The backup battery is continually recharged by the main battery pack. The mobile device is designed to work with a replaceable 3000 mAh Lithium-Polymer (Li-Poly) battery pack from LXE. Under normal conditions it should last approximately eight to ten hours before requiring a recharge. During very heavy scanning or RF transmitter use, the operating time of the battery may be less. The operating system keeps date and time valud for a minimum of four days using a fully charged backup battery and a main battery pack installed that has reached the Low Warning point. The status indicator is illuminated when the backup battery is being charged by the main battery pack. Main Battery Figure 30 Lithium Polymer Battery Pack CAUTION 1. Contacts, Battery Charging 2. Tab RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. ATTENTION II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type equivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. The main battery has a rugged plastic enclosure that is designed to withstand the ordinary rigors of an industrial environment. Exercise care when transporting the main battery making sure it does not come in contact with excessive heat or any power source other than an MX8 MultiCharger or the mobile device. A new main battery pack can be fully charged in 5 hours when it is in an MX8 connected to AC power and 5 hours when it is in the MX8 multi charger. MX8 User’s Guide E-EQ-MX8OGWW-A Batteries 43 Backup Battery For Review - Preliminary - Draft 01 - Not for distribution The internal 80mAh Nickel Metal Hydrate (NiMH) backup battery provides power to the device for a short amount of time when the main battery has been depleted, removed or has failed. The | Settings | Control Panel | Battery. backup battery status and conditioning is available using The backup battery is charged by the main battery pack only. Recharging maintains the battery near full charge at all times. If the backup battery is completely discharged, it may take up to 5 hours to recharge. The capability to discharge the backup battery is provided to allow the user to condition the battery in order to recover fully backup batttery capacity. Backup battery replacement must be performed by qualified service personnel. The backup battery has a minimum 2 years service life. Note: An uninterrupted external power source (wall AC adapters) transfers power to the computer’s internal charging circuitry which, in turn, recharges the main battery and backup battery. Frequent connection to an external power source, if feasible, is recommended to maintain backup battery charge status as the backup battery cannot be recharged by a dead or missing main battery. Battery Hotswapping Important: When the backup battery power is Low or Very Low ( | Settings | Control Panel | Power | Battery tab) connect the AC adapter to the MX8 before replacing the main battery pack. Replace the main battery pack after first pressing the Power key and placing the MX8 in Suspend Mode. LXE recommends any work in progress be saved prior to replacing the main battery pack. Simply replace the discharged main battery with a fully-charged main battery. A fully charged backup battery will retain data during a main battery hotswap for 5 minutes. Warning: E-EQ-MX8OGWW-A Never replace the main battery in a hazardous location. MX8 User’s Guide 44 MX8 Battery Multi-Charger MX8 Battery Multi-Charger – need data (battery retaining clip described in instructions) For Review - Preliminary - Draft 01 - Not for distribution The MX8 Multi-Charger is not approved for use in a Hazardous Location. Charge a Main Battery Pack The main battery pack can be charged while it is in the MX8 (connected to an AC power supply) or while it is in the LXE MX8 Multi-Charger. Please refer to the MX8 Multi-Charger User’s Guide for instruction. The multi-charger requires an external power source before battery pack charging/analyzing can commence. The external Power Supply for the Multi-charger is shipped with the multi-charger. MX8 Multi-Chargers are not approved for use in Hazardous Locations. need pic Figure 31 MX8 Multi-Charger / Analyzer Front Power Connection Battery Charging Pocket LCD Display LED Indicators need pic Figure 32 Insert Battery Pack in Charging Pocket 1. Battery Well 2. Retaining Clip 3. Battery Charging Contacts Lower the battery pack straight into the battery charger pocket and push it down firmly. Do not "slam" the battery into the charging cup or drop it into the cup. Failure to follow these instructions can result in damage to the main battery or the charger. Please refer to the MX8 Multi-charger User’s Guide for technical information and operating instructions. MX8 User’s Guide E-EQ-MX8OGWW-A Passive Vehicle Mount Cradle 45 Passive Vehicle Mount Cradle For Review - Preliminary - Draft 01 - Not for distribution A passive vehicle mount cradle is available for the MX8. The cradle restrains the MX8. The passive cradle does not have an external device connector e.g. power/RS-232 cable. Wireless client interaction is available as long as the mobile device has sufficient energy in the MX8 main battery pack and a clear signal path. The cradle is lined with strips of hook-and-loop fabric to ensure a snug fit between the MX8 and the inside of the cradle. The vehicle cradle should be mounted in an area in the vehicle where it: • Does not obstruct the driver’s vision or safe vehicle operation. • Will be protected from rain or inclement weather. • Will be protected from extremely high concentrations of dust or wind-blown debris. • Can be easily accessed by a user seated in the driver’s seat. There are two mounting options for the cradle: • U-bracket mounting • RAM ball cylinder mounting Before installation begins, verify you have the applicable vehicle mounting bracket assembly components necessary for your mount type, as shown in the section titled “Assembly Components”. Do not slide the MX8 into the passive cradle until the cradle is securely fastened to the vehicle. E-EQ-MX8OGWW-A MX8 User’s Guide 46 Passive Vehicle Mount Cradle Cradle Assembly Components For Review - Preliminary - Draft 01 - Not for distribution Note: Bolts, washers, and wrench needed when attaching the mobile device to the vehicle are not supplied by LXE. U-Bracket Figure 33 Passive Vehicle Mount Cradle and U-Bracket U-Bracket Footprint Not To Scale Figure 34 Bracket Mounting Footprint Note: MX8 User’s Guide LXE does not supply the bolts or washers needed when mounting the cradle assembly to the vehicle chassis. LXE recommends using bolts with a maximum 10/32” (0.3125) diameter. E-EQ-MX8OGWW-A Passive Vehicle Mount Cradle 47 For Review - Preliminary - Draft 01 - Not for distribution RAM Ball and Cylinder Figure 35 Passive Vehicle Mount Cradle / RAM Ball Assembly Figure 36 RAM Bracket Components Mount the cradle U-bracket to the upper RAM ball assembly with the bolts, washers and nuts supplied by LXE. Qty 4 – Hex Cap ¼-20 x ¾ bolts Qty 4 – ¼ flat washer Qty 4 – ¼-20 nylon insert lock nuts E-EQ-MX8OGWW-A MX8 User’s Guide 48 Passive Vehicle Mount Cradle For Review - Preliminary - Draft 01 - Not for distribution RAM Assembly Footprint Not To Scale Figure 37 RAM Assembly Footprint Note: MX8 User’s Guide LXE does not supply the bolts or washers needed when mounting the cradle assembly to the vehicle chassis. LXE recommends using bolts with a maximum 10/32” (0.3125) diameter. E-EQ-MX8OGWW-A Passive Vehicle Mount Cradle 49 For Review - Preliminary - Draft 01 - Not for distribution How to Install the Cradle U-Bracket 1. MX8 2. Angle Adjust Knob 3. Passive Cradle 4. U-Bracket 5. Mounting Bolt Figure 38 Install Cradle U-Bracket 1. Attach the U-Bracket to the vehicle, making sure it does not impede safe operation of the vehicle. 2. Attach the Passive Cradle to the U-Bracket using the Angle Adjust knobs. Use both knobs to loosen and tighten the cradle to the U-bracket while determining the best viewing angle. E-EQ-MX8OGWW-A MX8 User’s Guide 50 Passive Vehicle Mount Cradle For Review - Preliminary - Draft 01 - Not for distribution 3. The passive vehicle mounted cradle is ready for use. Periodically test the mounting device and retighten bolts and/or knob as needed. If the cradle becomes cracked or warped it must be replaced. MX8 User’s Guide E-EQ-MX8OGWW-A Passive Vehicle Mount Cradle 51 For Review - Preliminary - Draft 01 - Not for distribution How To Install the RAM Bracket 1. MX8 2. Angle Adjust Knobs 3. Passive Cradle 4. U-Bracket 5. Mounting Hex Bolt 6. Upper RAM Ball Assembly 7. Arm 8. Thumbscrew 9. Lower RAM Ball Assembly Figure 39 Install RAM Bracket Assembly 1. Attach the lower RAM ball assembly to the vehicle, making sure it does not impede safe operation of the vehicle. 2. Fasten the upper RAM ball assembly to the base of the U-bracket using the supplied bolts, washers and screws. E-EQ-MX8OGWW-A MX8 User’s Guide For Review - Preliminary - Draft 01 - Not for distribution 52 Passive Vehicle Mount Cradle 3. Loosen the turnscrew on the RAM arm, place the lower socket over the vehicle mount RAM ball, then the other arm socket over the RAM ball on the U-bracket. 4. Tighten the arm turnscrew until the U-bracket is secured to the RAM arm and the vehicle. 5. Attach the Passive Cradle to the U-Bracket using the Angle Adjust knobs. Use both knobs to loosen and tighten the cradle to the U-bracket while determining the best viewing angle. 6. MX8 User’s Guide The passive vehicle mounted cradle is ready for use. E-EQ-MX8OGWW-A For Review - Preliminary - Draft 01 - Not for distribution Passive Vehicle Mount Cradle 53 Periodically test the mounting device and retighten bolts and/or knob as needed. If the cradle or any cradle assembly component becomes cracked or warped it must be replaced before being placed into service. E-EQ-MX8OGWW-A MX8 User’s Guide Passive Vehicle Mount Cradle For Review - Preliminary - Draft 01 - Not for distribution 54 MX8 User’s Guide E-EQ-MX8OGWW-A Appendix A Key Maps For Review - Preliminary - Draft 01 - Not for distribution Introduction Remember : “Sticky” keys are also known as “second” function keys. Ctl/Ctrl, Alt, Shft, Blue and Orange keys are “sticky keys”. Sticky keys do not need to be held down before pressing the next (or desired) key. It is valid to use combined modifiers on specific keys. Note: The key mapping in this appendix relates to the physical keypad. See section titled Input Panel for the Virtual (or Soft) Keypad used with the stylus. 32-Key Numeric-Alpha Keypad When using a sequence of keys that require an alpha key, first press the Alph key. Use the Shft sticky key or the Caps key sequence (Blue+Tab) for upper case alphabetic characters. Pressing the Alph key forces “Alpha” mode for the 2,3,4,5,6,7,8, and 9 keys. The 1 and 0 keys continue to place a 1 and 0 into the text field. To create a combination of numbers and letters before pressing Enter, remember to tap the Alph key to toggle between Alpha and Numeric mode. When using a sequence of keys that do not include the Alph key but does include a sticky key, press the sticky key first then the rest of the key sequence. To Get This MX8 Key / Function Press These Keys and Then … Blue Orange Ctl Alt Shft Power / Suspend Field Exit (default VK_PAUSE) MAP MAP Diamond#1 MAP=Mappable Diamond#2 MAP Default is MAP MAP=Mappable Diamond#3 MAP or Volume Adjust Mode Press This Key Power or Alpha Default is MAP MAP=Mappable Scan Key Tapping the Power key when in any sticky mode (Blue, Orange, Shift, etc) either turns the device On (when Off) or places it in Suspend (when active). Orange+Scan enters Volume Adjust Mode. Use Up Arrow and Down Arrow to adjust volume. Press any other key but Up Arrow or Down Arrow to exit Adjust Mode. E-EQ-MX8OGWW-A MX8 User’s Guide 56 32-Key Numeric-Alpha Keypad To Get This MX8 Key / Function For Review - Preliminary - Draft 01 - Not for distribution Display Backlight Brightness Adjust Mode Press These Keys and Then … Blue Orange Ctl Alt Shft Alpha Press This Key Scan Key Toggle Blue Mode Blue Toggle Orange Mode Orange Toggle Shift Mode Shft Toggle Alpha Mode Alph Alt Mode Alt Control Mode Ctrl Scan Mode Scan Key Esc Alt Space Spc Enter Enter CapsLock (Toggle) Back Space Tab Spc Tab Tab BackTab Tab Up Arrow Up Arrow Down Arrow Down Arrow Right Arrow Up Arrow Left Arrow Down Arrow Insert Ctrl Delete Del Home Down Arrow End Up Arrow Page Up Up Arrow Page Down Down Arrow F1 F1 F2 F2 F3 F3 F4 F4 F5 F5 F6 F1 F7 F2 F8 F3 F9 F4 F10 F5 F11 F1 F12 F2 Blue+Scan enters Backlight Brightness Adjust Mode. Use the Up Arrow and Down Arrow to adjust brightness. Press any other key but Up Arrow or Down Arrow to exit Adjust Mode. MX8 User’s Guide E-EQ-MX8OGWW-A For Review - Preliminary - Draft 01 - Not for distribution 32-Key Numeric-Alpha Keypad 57 Press These Keys and Then … To Get This MX8 Key / Function Blue F13 F3 F14 F4 F15 F5 Orange Ctl Alt Shft Alpha Press This Key F16 F1 F17 F2 F18 F3 F19 F4 F20 F5 F21 F1 F22 F2 F23 F3 F24 F4 22 222 33 333 44 444 55 555 66 666 77 777 7777 88 888 99 999 9999 22 E-EQ-MX8OGWW-A MX8 User’s Guide 58 32-Key Numeric-Alpha Keypad For Review - Preliminary - Draft 01 - Not for distribution To Get This MX8 Key / Function Press These Keys and Then … Blue Ctl Alt Press This Key Shft Alpha 222 33 333 44 444 55 555 66 666 77 777 7777 88 888 99 999 9999 . (period) DEL or MX8 User’s Guide Orange E-EQ-MX8OGWW-A 32-Key Numeric-Alpha Keypad To Get This MX8 Key / Function 59 Press These Keys and Then … Blue Orange Ctl Alt Shft For Review - Preliminary - Draft 01 - Not for distribution Press This Key or Alpha Diamond#2 Spc Del * (asterisk) or Diamond#1 . (period) Del : (colon) ; (semicolon) ` (accent) _ (underscore) , (comma) ‘ (apostrophe) Alph ~ (tilde) “ Alt Alph Diamond#3 or or or or or E-EQ-MX8OGWW-A Ctrl MX8 User’s Guide 60 32-Key Numeric-Alpha Keypad To Get This MX8 Key / Function Press These Keys and Then … Blue Orange Ctl Alt Shft or For Review - Preliminary - Draft 01 - Not for distribution Press This Key Diamond#2 Diamond#3 or MX8 User’s Guide Alpha 0 (zero) E-EQ-MX8OGWW-A For Review - Preliminary - Draft 01 - Not for distribution Appendix B Regulatory Notices and Safety Information FCC Information: This device complies with FCC Rules, part 15. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning: Changes or modifications to this device not expressly approved by LXE, Inc., could void the user’s authority to operate this equipment. EMC Directive Requirements: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Industry Canada: This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe A prescrites dans le Règlement sur le brouillage radioélectrique édits par le ministère des Communications du Canada. Notice: The long term characteristics or the possible physiological effects of radio frequency electromagnetic fields have not been investigated by UL. Li-Polymer Battery When disposing of the MX8 main battery, the following precautions should be observed: The battery should be disposed of promptly. The battery should not be disassembled or crushed. The battery should not be heated above 212°F (100°C) or incinerated. Important: This symbol is placed on the product to remind users to dispose of Waste Electrical and Electronic Equipment (WEEE) appropriately, per Directive 2002-96-EC. In most areas, this product can be recycled, reclaimed and re-used when properly discarded. Do not discard labeled units with trash. For information about proper disposal, contact LXE through your local sales representative, or visit www lxe com. E-EQ-MX8OGWW-A MX8 User’s Guide 62 Appendix B Regulatory Notices and Safety Information This device contains transmitter Module FCC ID: KDZLXE4830P RF Safety Notice (Summit Client - 4830) For Review - Preliminary - Draft 01 - Not for distribution Caution This portable device with its antenna complies with FCC’s and Industry Canada’s RF exposure limits set for an uncontrolled environment. This equipment has shown compliance with FCC and Industry Canada Specific Absorption Rate (SAR) limits. Highest reported SAR for the MX8 is .758W/kg on body. Any accessories not provided by LXE should not be used with this device. This device must not be co-located or operating in conjunction with any other antenna or transmitter. R&TTE Directive Requirements (Applies only to equipment operated within the EU/EFTA) Information to User A label on the exterior of the device should resemble one of the labels shown below (the label contains the LXE part number of the installed radio card). The labels shown below and affixed to the device, identify where the device may be used and where its use is restricted. Use of a device is prohibited in countries not listed below or otherwise identified by the label. (May or may not include the 0560 Notifed Body No. Substitute 4 digit Notified Body No. may also be applied.) Republic of Singapore - LXE Dealer License Number DA103458 complies with IDA Standards. MX8 Approvals/Standards Product EMI / EMC Standards Safety Standards MX8 FCC Part 15 Subpart B, Class A EN 55022 UL 60950 / CSA C22.2 No. 60950 IEC/EN 60950-1 Class A (CISPR 22) EN 55024:1998 AS/NZS 3548, Class A (CISPR 22) CDRH: 21 CFR 1040.10 IEC/EN 60825-1 Transceiver: Transceiver RF (2.4 GHz) standards RF Safety Standards MX8 with 802.11b/g [Summit Client - 4830] FCC Part 15.247, Subpart C FCC Bulletin OET-65 EN 300 328 FCC O.E.T. Bulletin 65 Industry Canada RSS 102 IC-RSS 210 IC-RSS 102 MX8 User’s Guide E-EQ-MX8OGWW-A Appendix B Regulatory Notices and Safety Information 63 For Review - Preliminary - Draft 01 - Not for distribution LXE Transceiver LXE 4830 Declaration of Conformity 1999/5/EC 93/68/EEC Type of Equipment: Brand Name or Trademark: Type Designation: Manufacturer: Address: Year of Manufacturer: DECLARATION OF CONFORMITY according to Directives: Radio Equipment and Telecommunications Terminal Equipment and the mutual recognition of their conformity CE Marking Directive Direct Sequence 2.4 GHz Wireless LAN Card LXE LXE 4830 LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA 2006 The following harmonized European Standards, technical specifications, or other normative documents have been applied: EMC: EN 301 489-1: 07-2000 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-17 07-2000 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for Wideband data and HIPERLAN equipment Radio: EN 300 328-1 and -2: 2000-7 Radio Equipment and Systems (RES); Wideband transmission systems; Technical characteristics and test conditions for data transmission equipment operating in the 2.4 GHz ISM band and using spread spectrum modulation techniques Safety: EN 60950-1: 2001 Safety of information technology equipment, including electrical business equipment We, LXE Inc., declare that the equipment specified above complies with all Essential Health and Safety Requirements of the above Directives and Standards, as amended. Place Date of issue LXE Inc., Norcross GA USA 23 October 2006 C. Binnom Jr. RF Approvals Engineer LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA ph. 770/447-4224 fax 770/447-6928 E-EQ-MX8OGWW-A MX8 User’s Guide 64 Appendix B Regulatory Notices and Safety Information Annex to DoC for LXE 4830 With regard to the use of external antennas For Review - Preliminary - Draft 01 - Not for distribution The LXE 4830 can be equipped with external antennas. The antennas listed have been evaluated with the LXE 4830 pursuant to EN 300 328, and therefore meet the definition of ‘dedicated antenna’ per ERC/REC 70-03 Appendix 1 Table 3; thus the requirement set forth in ERC/REC 70-03 , Annex 3 are met by the LXE model 4830 transceiver. Dedicated Antennas for use with LXE 4830 LXE P/N Antenna Gain Radio Power Level Antenna Description 153180-0001 160952-0001 158399-0001 159900-0001 160019-0001 160501-0001 161029-0001 2.2 dBi 0 dBi 0 dBi 0 dBi 0 dBi 0 dBi 0 dBi 15.8 dBm 15.8 dBm 15.8 dBm 15.8 dBm 15.8 dBm 15.8 dBm 15.8 dBm Omni, for LXE VX-series computers Omni, for LXE MX3-series computers Omni, for LXE MX5-series computers Omni, for LXE MX8-series computers Omni, for LXE VX-series computers Omni, for LXE HX1-series computers Omni, for LXE RX2-series computers C. Binnom Jr. RF Approvals Engineer 23 October 2006 LXE Inc. 125 Technology Parkway Norcross, GA 30092-2993 USA ph. 770/447-4224 MX8 User’s Guide fax 770/447-6928 E-EQ-MX8OGWW-A Appendix B Regulatory Notices and Safety Information 65 A/C Power Supply Safety Statement – MX8 Output Rated 5 VDC, 1.25 A. For Review - Preliminary - Draft 01 - Not for distribution The LXE-approved AC Power Adapter is only intended for use in a 25°C (77°F) maximum ambient temperature environment. need pic Optional A/C Power Supply: Outside North America, this unit is intended for use with an IEC certified ITE power supply with output rated as stated at the top of this page. (US) Alimentation c.a. optionnelle: Hors de l'Amérique du Nord, cette unité est conçue pour être utilisée avec une alimentation ITE certifiée CEI de sortie nominale indiquée au haut de cette page. (FR) Valgfrit vekselstrømforsygning Udenfor Nord Amerika er denne enhed udstattet med en IEC (international elektronisk Kommission) udfærdiget med en ITE strømforsygning med strømudgang som fastslået på denne sides begyndelse. (DK) Vaihtoehtoinen vaihtovirran syöttölaite: Pohjois-Amerikan ulkopuolella tämä laite on tarkoitettu käytettäväksi sellaisen IEC:n sertifioiman ITE-tehonsyöttölaitteen kanssa, jonka antoteho on tämän sivun yläosassa esitetyn mukainen. (FI) Optionales Netzteil (Wechselstrom) Außerhalb Nordamerikas sollte diese Einheit über ein der IEC-Norm entsprechendes ITE-Netzteil gespeist werden, und zwar mit einer wie oben auf dieser Seite genannten Ausspeisung. (DE) Προαιρετική Τροφοδοσία Συνεχούς Ρεύματος Εκτός Β. Αμερικής, η μονάδα αυτή προορίζεται για χρήση με ένα τροφοδοτικό ITE πιστοποιημένο κατά IEC με ονομαστική ισχύ όπως δηλώνεται στην αρχή της σελίδας. (GR) Alimentazione opzionale a corrente alternata: Al di fuori dei paesi dell'America del nord, l'unità deve essere impiegata con un dispositivo d'alimentazione per attrezzature informatiche approvato dalla IEC la cui potenza nominale sia pari a quella indicata all'inizio della pagina. (IT) Vekselstrømforsyning (ekstrautstyr): Utenfor Nord-Amerika skal dette produktet brukes med en IEC-sertifisert ITE-strømforsyning med klassifisert effekt som angitt øverst på denne siden. (NO) Fornecimento opcional de CA: Fora dos EUA, esta unidade destina-se a ser usada com dispositivos de fornecimento de corrente ITE com certificação IEC, com a capacidade indicada no topo desta página. (PT) Suministro optativo de corriente alterna Fuera de América del Norte, esta unidad se debe utilizar con un alimentador ITE homologado por la IEC (comisión electrotécnica internacional) con una salida que tenga la calificación que figura en la parte superior de esta página. (ES) Valfri A/C Strömförsörjning Utanför Nordamerika är det meningen att denna enheten används med en IEC-certifierad ITE-strömförsörjare med den uteffekt som anges längst uppe på den här sidan. (SE) İsteğe Bağlı A/C Güç Kaynağı: Kuzey Amerika dışında, bu ünite, çıkış sınıflandırması bu sayfanın başında belirtilen IEC sertifikalı bir ITE güç kaynağı ile birlikte kullanılmak üzere tasarlanmıştır. (TR) Updated 10/01/2001 Legend: Danish – DK; English – US; Finnish – FI; French- - FR; German – DE; Greek – GR; Italian – IT; Norwegian – NO; Portuguese – PT; Spanish – ES; Swedish – SE; Turkish – TR. E-EQ-MX8OGWW-A MX8 User’s Guide 66 Appendix B Regulatory Notices and Safety Information Laser Light Safety Statement For Review - Preliminary - Draft 01 - Not for distribution Warning: This product uses laser light. One of the following labels is provided on the scanner. Please read the Caution statement. (US) Mise én garde: Ce produit utilise un rayon laser. L’une des étiquettes suivantes est apposée sur le scanneur. Veuillez lire l’avertissement qu’elle contient. (FR) Advertência: Este produto usa luz de laser. O scanner contém um dos seguintes avisos. Favor ler o Aviso. (PT) Varning: Denna produkt använder laserljus. En av de nedanstående etiketterna sitter på scannern. Var god läs varningstexten. (SE) Advarsel: Dette produkt anvender laserlys. En af følgende mærkater anvendes på scanneren. Læs venligst sikkerhedsforanstaltningen. (DK) Varoitus: Tämä tuote käyttää laservaloa. Skannerissa on jokin seuraavista tarroista. Lue Huomio-kohta. (FI) Warnung: Dieses Produkt verwendet Laserlicht. Eines der folgenden Etiketten befindet sich auf dem Scanner. Bitte lesen Sie den Gefahrenhinweis. (DE) Attenzione: Questo prodotto utilizza luce laser. Una delle etichette seguenti c’ ubicata sullo scanner. Si raccomanda di leggere con attenzione le avvertenze riportate. (IT) Advarsel: Dette utstyret bruker laserlys. En av følgende etiketter er plassert på scanneren. Les advarselen på etiketten. (NO) Advertencia: Este producto usa luz de láser. Las etiquetas se proveen en la máquina exploradora. Por favor, lea detenidamente la explicación para las precauciones. (ES) Waarschuwing: Dit product gebruikt laserlicht. Een van de volgende labels is op de scanner aangebracht. Lees a.u.b. de waarschuwing onder Oppassen. (NL) MX8 User’s Guide E-EQ-MX8OGWW-A Appendix B Regulatory Notices and Safety Information 67 For Review - Preliminary - Draft 01 - Not for distribution Laser Light Safety Statement Aþaðýdaki etiketlerden bir tanesi tarayýcýnýn üstünde saðlanýr. Lütfen Dikkat ifadesini okuyun. (TR) (KR) (CN) E-EQ-MX8OGWW-A (GR) (JP) Legend: Chinese-CN; Danish-DK; Dutch-NL; English-US; Finnish-FI; French-FR; German-DE; Greek-GR; Italian-IT; Japanese-JP; Korean-KR; Norwegian-NO; Portuguese-PT; Spanish-ES; Swedish-SE; TurkishTR MX8 User’s Guide 68 Appendix B Regulatory Notices and Safety Information For Review - Preliminary - Draft 01 - Not for distribution Labels – MX8 Hand Held Computer [Summit Client] MX8 User’s Guide E-EQ-MX8OGWW-A Index 69 For Review - Preliminary - Draft 01 - Not for distribution Index 2D Imager .............................................................27 2nd key function, described ..................................40 32-key Keymap.....................................................55 AC External Power Supply, How to .....................21 AC Power and LEDs on multicharger ..................................44 AC Power Adapter Assembly ............................................................21 AC Power Scheme................................................36 Accessories Electrostatic Discharge .......................................13 Installing .............................................................13 Activation Key AppLock .............................................................19 Alph key Enter a string of letters in a text field ..................41 Alpha Mode LED .................................................39 Alt key function ....................................................40 Alt sticky keypress................................................40 Assemble RS232 connection .........................................22, 23 USB connection ..................................................22 Audio Cable Install ..................................................................23 Audio Volume settings .........................................37 Backlight timer .....................................................35 battery trickle charging ...................................................15 Battery ..................................................................42 charge before using .............................................15 Check status ........................................................15 Check status and power reading..........................16 Compartment.......................................................15 Important...............................................................3 status LED...........................................................15 Battery Multi-Charger ..........................................44 Battery Power Scheme..........................................36 Battery, Backup described .............................................................43 Battery, Main described .............................................................42 E-EQ-MX8OGWW-A Bluetooth icons .....................................................29 Bluetooth printers and scanners ............................29 Cable Adapter, Audio....................................................10 Multipurpose RS-232 and Power ........................10 Multipurpose USB and Power ............................10 CapsLock key sequence........................................41 CapsLock mode function ......................................41 Change the Time and Date....................................13 Charger, battery ....................................................44 Cleaning................................................................34 Cold Reset.............................................................33 Cold reset, How to ................................................33 Color Display........................................................34 Color displays and backlight timers......................35 Components ............................................................6 Connect External PS .............................................21 Contact LXE .........................................................30 Control sticky keypress.........................................40 Ctrl key function ...................................................40 Data entry imager .................................................................27 keypad.................................................................25 laser scanner........................................................27 stylus ...................................................................26 virtual keyboard ..................................................25 Data entry .............................................................25 Display..................................................................34 Display and scanner aperture cleaning .................34 Display backlight timer.........................................35 Enter key function.................................................39 Entering Data ........................................................25 Environmental Specifications .................................4 External PS ...........................................................21 MX8 User’s Guide 70 For Review - Preliminary - Draft 01 - Not for distribution Features...................................................................2 Footprint passive vehicle cradle, RAM assembly...............48 passive vehicle cradle, U-bracket........................46 Forms entry...........................................................25 Function 2nd Key...............................................................40 Alt Key................................................................40 CapsLock Mode ..................................................41 Ctrl Key...............................................................40 Enter Key ............................................................39 Shft Key ..............................................................40 Spc Key...............................................................39 Function keys........................................................40 Index Keypad, 32 Key ....................................................24 Li-Polymer battery life .........................................16 Lithium-Polymer (Li-Poly)...................................42 Microphone adjustment ........................................23 Mode Key Functions.............................................41 Mode timers ..........................................................36 Nickel Metal Hydrate (NiMH) .............................43 Getting Started ......................................................13 Operating Temperature ...........................................4 Orange and Blue sticky keypresses.......................40 Overview ................................................................1 Handstrap................................................................9 Handstrap or Trigger Handle ..................................9 Handstrap, installation ..........................................20 Headset, Install .....................................................23 Help ......................................................................30 Hotswapping cautions ...............................................................43 IEC IP54 .................................................................4 Input panel virtual keyboard ..................................................25 Install Passive Mounting Bracket, Vehicle ....................45 Passive vehicle cradle ...........................................45 Passive Vehicle Mounting Bracket Installation Procedure .........................................45 Pen Stylus and data entry......................................................26 Power key .............................................................16 Power Scheme ......................................................36 Protective Film .....................................................34 Quick Start Instructions ........................................13 Key Alpha...................................................................39 Diamond..............................................................39 Enter....................................................................39 Numeric ..............................................................39 Scan.....................................................................39 Space...................................................................39 Key functions........................................................40 Keypad and entering data .................................................25 Keypad Shortcuts..................................................17 MX8 User’s Guide Reboot, How to.....................................................33 Recalibrate ............................................................18 Registry and save settings.....................................33 Regulatory Notices ...............................................61 Safety Information ................................................61 Save settings .........................................................33 E-EQ-MX8OGWW-A For Review - Preliminary - Draft 01 - Not for distribution Index Scan Status LED ...................................................39 Scanner Aperture identify type ...............................8 Scanning and data entry........................................27 Scanning status, LED............................................28 Scheme..................................................................36 Screwdriver Phillips, for handstrap .........................................20 Setting the Time Zone ..........................................18 Shift key function .................................................40 Shift keypress and sticky keys ..............................40 Sound Scheme ......................................................37 Space key function................................................39 Specifications Environmental.......................................................4 Sticky Key ............................................................40 Stylus and data entry......................................................26 Suspend mode, How To........................................16 Suspend Timer ......................................................36 Switch applications AppLock .............................................................19 System Idle Timer.................................................36 System Status LED ...............................................38 Technical Glossary ...............................................30 Tethered scanners .................................................28 Timer User, System, Suspend........................................36 Touch Screen ........................................................34 Touch Screen and Keypad Shortcuts ....................17 Touch Screen and the Stylus.................................17 E-EQ-MX8OGWW-A 71 Touch screen calibration.......................................18 Touchscreen and data entry......................................................26 Trigger Handle........................................................8 Troubleshooting Startup.................................................................14 User Idle Timer.....................................................36 Vehicle Cradle Assembly ............................................................45 Virtual keyboard Input panel ..........................................................25 Voice data .............................................................28 Volume adjust audio volume ............................................37 Warm Reset ..........................................................33 WARMBOOT.EXE..............................................33 Warnings and Labels Laser Scanner..................................................5, 27 When the backup battery power is Low or Very Low...................................................................43 MX8 User’s Guide For Review - Preliminary - Draft 01 - Not for distribution 72 MX8 User’s Guide Index E-EQ-MX8OGWW-A
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Page Mode : UseOutlines Signing Date : 2007:08:03 12:32:29-04:00 Signing Authority : ARE_Acrobat Collaboration V7.0 P9 0000109 Annotation Usage Rights : Create, Delete, Modify, Copy, Import, Export XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Create Date : 2007:08:03 12:24:09-04:00 Creator Tool : Acrobat PDFMaker 7.0.7 for Word Modify Date : 2007:08:03 12:32:29-04:00 Metadata Date : 2007:08:03 12:32:29-04:00 Format : application/pdf Title : MX8 User's Guide Creator : LXE Document ID : uuid:d73e00d0-5c8e-43af-b9a5-8768fb08524d Instance ID : uuid:5dd7dbd1-c202-41ee-b938-80d37c0be094 Company : LXE Has XFA : No Page Count : 78 Page Layout : OneColumn Author : LXEEXIF Metadata provided by EXIF.tools