LG Electronics USA 50PC3DUUE Plasma Display Panel User Manual 38289U0527F LG PDP
LG Electronics USA Plasma Display Panel 38289U0527F LG PDP
Contents
- 1. User Manual
- 2. User Manual 1
- 3. User Manual 2
- 4. User Manual 3
User Manual 1
S-VIDEO VIDEO AUDIO AV OUT AV IN 1 COMPONENT IN AUDIO VIDEO COMPONENT IN AUDIO VIDEO Introduction AV OUT AV IN 1 Connection Options (Model Name: 32/37/42LC2DU) S-VIDEO VIDEO AUDIO - This picture shown below may be somewhat different from your TV. S-VIDEO Input Provides better picture quality than the video input. VIDEO Input Connects the video signal from a video device. AUDIO Input Connections are available for listening to stereo sound from an external device. AC IN 11 10 SERVICE AUDIO VIDEO (PC) AUDIO VIDEO ANTENNA/ CABLE IN 1(DVI) OPTICAL RS-232C IN (CONTROL & SERVICE) DIGITAL AUDIO OUT (MONO) S-VIDEO VIDEO AUDIO COMPONENT IN Connect a component video/audio device to these jacks. S-VIDEO VIDEO AV OUT Connect a second TV or monitor. AV (Audio/Video) IN 1 Connect audio/video output from an external device to these jacks. S-VIDEO Connect S-Video out from an S-VIDEO device. ANTENNA/CABLE IN Connect over-the air signals to this jack. Connect cable signals to this jack. DIGITAL AUDIO OUT Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work. HDMI IN Connect a HDMI signal. Or DVI (VIDEO)signal to the this port with a HDMI to DVI cable. AUDIO AV OUT AV IN 1 AV OUT AV IN 1 COMPONENT IN HDMI IN COMPONENT IN RGB IN RGB IN (PC) Connect the monitor output from a PC to the appropriate input port. Remote Control Port Connect your wired remote control. AUDIO IN (RGB/DVI) Connect the monitor output from a PC to the appropriate input port. RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC. 10 SERVICE 11 Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power. 11 Introduction Remote Control Key Functions POWER Turns your TV or any other programmed equipment on or off, depending on mode. INPUT TV INPUT POWER DVD TV CABLE AUDIO INPUT VCR MODE TV INPUT Rotates the input mode between Antenna and Cable. In AV12, Component 1-2, RGB-DTV (or RGB-PC), HDMI1/DVI, and HDMI2 input sources, screen returns to the last TV channel. External input modes rotate in regular sequence: TV, AV1-2, Component 1-2, RGB-PC, HDMI1/DVI or HDMI2. STB (AV 1-2, Component 1-2, RGB-PC , HDMI1/DVI or HDMI2 input sources are linked automatically, only if these are connected.) T- BRIGH MENU BRIGH MODE Selects the remote operating mode: TV, DVD, VCR, AUDIO, CABLE, or STB. Select a mode other than TV, for the remote to operate an external device. ENTER EXIT VOL TIMER RATIO MUTE FAV INFO CH MENU Brings up the main menu to the screen. BRIGHT + / - Adjust brightness on screen. - It turns to the default settings brightness by changing mode source. FLASHBK EZ PIC EZ SOUND ADJUST SAP THUMBSTICK (Up/Down/Left/Right/ENTER) Allows you to navigate the on-screen menus and adjust the system settings to your preference. CC EXIT Clears all on-screen displays and returns to TV viewing from any menu. TIMER G p.43 Lets you select the amount of time before your TV turns itself off automatically. RATIO G p.45 Changes the aspect ratio. INFO (Refer to p.15) When you watch the TV, information displays on top of the screen. Not available in Component 1-2, RGB, HDMI1/DVI and HDMI2 mode. 12 Introduction INPUT TV INPUT POWER DVD TV AUDIO VCR MODE CABLE STB DAY - MENU DAY+ GUIDE RATIO TIMER PAGE FLASHBK EZ PIC EZ SOUND ADJUST APM SAP MUTE G p.27 Switches the sound on or off. NUMBER BUTTONS CH FAV MUTE CHANNEL UP/DOWN Selects available channels found with EZ scan and Manual scan. INFO CC PAGE VOL VOLUME UP/DOWN Increases/decreases the sound level. FAV Use to scroll the Favorite channels. ENTER EXIT VCR/DVD/DVHS/Camcorder BUTTONS Control some video cassette recorders or DVD players ("RECORD" button is not available for DVD player). FREEZE — (DASH) Used to enter a program number for multiple program channels such as 2-1, 2-2,etc. FLASHBK Returns to the last channel viewed. EZ PIC G p.33 Selects a factory preset picture mode depending on the viewing environment. EZ SOUND G p.39 Selects the sound appropriate for the program's character. SAP Selects MTS sound: Mono, Stereo, and SAP in analog mode. Change the audio language in DTV mode. CC G p.46 (*In DTV/CADTV mode G p.46 ) Select a closed caption: Off, CC1~4, Text1~4. ADJUST Adjusts screen position, size, and phase in PC mode. 13 Introduction Remote control effective range Installing Batteries /32/37/42LC2DU 42PC3DU/3DVU/50PC3DU ■ INPUT TV Open the battery compartment cover on the back side and install the batteries matching correct polarity (+with +,-with -). ■ Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones. ■ Close cover. INPUT TV DVD ARC VCR DVD TEXT VCR PIP SIZE PIP PR - PIP PR + SWAP SIZE PIP PIP PR - PIP PR + SWAP LIST MENU EXIT POSITION PIP INPUT INPUT TV TV POWER INPUT DVD ARC TEXT VCR PIP SIZE PIP PR - PIP PR + SWAP POSITION PIP INPUT POSITION PIP INPUT MENU EXIT LIST TV POWER INPUT TV POWER INPUT ARC TEXT 60PC1D LIST I/II SLEEP MENU EXIT I/II SLEEP I/II SLEEP OK OK OK Q.VIEW Q.VIEW ■ Use a remote control up to 7 meters distance and 30 degree (left/right) within the receiving unit scope. ■ Dispose of used batteries in a recycle bin to preserve environment. ATTACHING THE TV TO A WALL We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV. 42PC3DU/3DVU/50PC3DU/60PC1D ■ 32/37/42LC2DU Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture. * If your product has the bolts in the eye-bolts position, loosen the bolts. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) on the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely. ■ 14 Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product. Installation Installation DESKTOP PEDESTAL INSTALLATION For proper ventilation, allow a clearance of 4inches on each side from the wall. 42PC3DU/3DVU/50PC3DU/60PC1D 4 inches 4 inches 4 inches 32/37/42LC2DU 4 inches 4 inches 4 inches 4 inches 4 inches CAUTION ■ Ensure adequate ventilation by following the clearance recommendations. This picture shown below may be somewhat different from your TV. Power Supply Short-circuit Breaker GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. 15 Basic Connection (For 32/37/42LC2DU) Connect the cables as necessary. After connecting the cables neatly, arrange the cables to the Cable Holder. To connect an additional equipment, see the External equipment Connections section. Cable holder 32LC2DU 37/42LC2DU CABLE MANAGEMENT Reinstall the CABLE MANAGEMENT as shown. 32LC2DU 37/42LC2DU Bundle the cables using the supplied twister holder. 32LC2DU 37/42LC2DU How to remove the CABLE MANAGEMENT - Hold the CABLE MANAGEMENT with both hands and pull it upward. Do not hold the CABLE MANAGEMENT when moving the product. - If the product is dropped, you may be injured or the product may be broken. 16 CABLE MANAGEMENT Basic Connection How to use stand (For 42PC3DU/3DVU) Place the set with the screen facing down on a cushion or soft cloth as shown. Before unfolding the stand, please make sure two locks (A) on the bottom of the stand push outward. Pull the stand out as shown. After unfolding the stand, please insert and tighten the screws (provided as parts of the product) in the holes (B) on the bottom of the stand. (A) (B) When connecting cables to the set, Do not disengage the lock (C). This may cause the set to fall, causing serious bodily injury and serious damage to the set. (C) * Image shown here may be slightly different from your set. When closing the stand for storage - First remove the screws in the holes (B) on the bottom of the stand. And then pull two Hooks (D) of the stand bottom and fold the stand into the back of the set. - After folding, push the two Locks (A) of the stand bottom outward. (A) (B) (D) How to arrange the cable (For 50PC3DU) Hold the CABLE MANAGEMENT with both hands and push it as shown. Reinstall the CABLE MANAGEMENT as shown. Connect the cables as necessary. To connect an additional equipment, see the External equipment Connections section. For 60PC1D, 42PC3DU/3DVU Arrange the cable as shown. 17 Installation External Equipment Connections NOTE: All cables shown are not included with the TV Antenna Or Cable Connection Analog and Digital TV signals provided on antenna - Antenna or Cable Service without a Cable Box Connection. - For optimum picture quality, adjust antenna direction if needed. Multi-family Dwellings/Apartments (Connect to wall antenna socket) Wall Antenna Socket OPTICAL ANTENNA/ CABLE IN DIGITAL AUDIO OUT RF Coaxial Wire (75 ohm) VHF Antenna Turn clockwise to tighten. UHF Antenna Outdoor Antenna Bronze Wire Be careful not to bend the bronze wire when connecting the antenna. Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Analog and Digital TV signals provided on cable Cable TV Wall Jack OPTICAL ANTENNA/ CABLE IN RF Coaxial Wire (75 ohm) DIGITAL AUDIO OUT Turn clockwise to tighten. Analog and DTV signals provided on two separate antennas Bronze Wire Antenna RF Coaxial Wire (75 ohm) Turn clockwise to tighten. Cable TV Wall Jack RF Coaxial Wire (75 ohm) • In a poor signal area to improve picture quality, purchase and install a signal amplifier. • If OPTICAL the antenna needs to be split for two TV’s, install a “2-Way Signal Splitter” in the connections. DIGITAL AUDIO S-VIDEO VIDEO AUDIO OUT antenna is not installed properly, contact your dealer for assistance. • If the AV OUT AV IN 1 signal amplifier COMPONENT IN Bronze Wire AUDIO VIDEO ANTENNA/ CABLE IN ANTENNA/ CABLE IN VIDE 18 S-VID Installation VCR Setup - To avoid picture noise (interference), leave an adequate distance between the VCR and TV. - Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. When connecting with an antenna Connect the RF antenna out socket of the VCR to the Antenna socket on the set. Connect the antenna cable to the RF antenna in socket of the VCR. Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) Select AV1 input source using the INPUT button on the remote control. - If connected to AV IN2, select AV2 input source. VCR ANT IN ANT OUT S-VIDEO OUT (R) AUDIO (L) VIDEO OUTPUT SWITCH IN SERVICE RGB IN (PC) AUDIO IN (RGB/DVI) HDMI IN REMOTE CONTROL IN 1(DVI) ANTENNA/ SERVICE CABLE IN IN RGBRS-232C IN (CONTROL & SERVICE) SERVICE) (PC) REMOTE CONTROL IN AUDIO IN (RGB/DVI) HDMI / DVI IN ANTENNA/ CABLE IN RS-232C IN (CONTROL & SERVICE) When connecting with a RCA cable VCR ANT IN OUT S-VIDEO ANT OUT (R) AUDIO (L) VIDEO OUTPUT SWITCH IN OPTICAL COMPONENT IN DIGITAL AUDIO VIDEOS-VIDEO VIDEOAUDIO AUDIO OUT AV V OUT AV V IN 1 OPTICAL PTICAL DIGITAL AUDIO DIGITAL OUT (MONO) S-VIDEO VIDEO AV OUT AV IN 1 COMPONENT IN AUDIO VIDEO AUDIO • If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the set. OPTICAL VIDEOS-VIDEO AUDIO VIDEO COMPONENT IN AV OUT A DIGITAL AUDIO OUT AUDIO COMPONENT IN AV OUT AV IN 1 AUDIO VIDEO 19 Installation S-VIDEO VIDEO AUDIO AV OUT AV IN 1 OPTICAL DIGITAL AUDIO OUT COMPONENT IN AUDIO VIDEO When connecting with an S-Video cable VCR Connect the S-VIDEO output of the VCR to the SVIDEO input on the set. The picture quality is improved; compared to normal composite (RCA cable) input. Connect the audio outputs of the VCR to the AUDIO input jacks on the set. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) Select AV1 input source with using the INPUT button on the remote control. - If connected to AV IN2, select AV2 input source. ANT IN S-VIDEO OUT ANT OUT (R) AUDIO (L) VIDEO OUTPUT SWITCH IN OPTICAL PTICAL DIGITAL AUDIO DIGITAL OUT (MONO) S-VIDEO VIDEO AUDIO V OUT AV COMPONENT IN AV V IN 1 AUDIO VIDEO Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work. External AV Source Setup Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). Select AV2 input source with using the INPUT button on the remote control. - If connected to AV IN1 input, select AV1 input source. Operate the corresponding external equipment. Refer to external equipment operating guide. Camcorder Video Game Set 20 AUDIO R VIDEO • This TV finds the connected input sources automatically for AV1, AV2, Component 1-2, RGB, HDMI1/DVI and HDMI2 sources are connected. HDMI / DVI IN ANTENNA/ CABLE IN COMPONENT IN AUDIO VIDEO Installation DVD Setup When connecting with a S-Video cable DVD (R) AUDIO (L) S-VIDEO COMPONENT IN AUDIO VIDEO AV V OUT AV V IN 1 OPTICAL DIGITAL AUDIO DIGITAL OUT (MONO) S-VIDEO VIDEO AUDIO Connect the S-VIDEO output of the DVD to the S-VIDEO input on the set. Connect the audio outputs of the DVD to the AUDIO input jacks on the set. Turn on the DVD player, insert a DVD. Select AV1 input source with using the INPUT button on the remote control. - If connected to AV IN2, select AV 2 input source. Refer to the DVD player's manual for operating instructions. When connecting with a HDMI cable HDMI IN 1(DVI) ANTENNA/ CABLE IN COMPONENT IN AUDIO VIDEO DVD HDMI-DVD OUTPUT Connect the HDMI output of the DVD to the HDMI IN 1(DVI) or 2 jack on the set. Select HDMI1/DVI or HDMI2 input source with using the INPUT button on the remote control. Refer to the DVD player's manual for operating instructions. S-VIDEO VIDEO AUDIO AV OUT AV IN 1 OPTICAL DIGITAL AUDIO OUT COMPONENT IN AUDIO VIDEO • TV can receive the video and audio signal simultaneously with using a HDMI cable. • If the DVD supports Auto HDMI function, the DVD output resolution will be automatically set to 1280x720p. • If the DVD does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the DVD to 1280x720p. 21
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 11 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:4eff007a-7201-4c51-886d-28bf18a4cd3a Modify Date : 2006:07:29 10:26:32+09:00 Create Date : 2006:07:29 10:26:15+09:00 Metadata Date : 2006:07:29 10:26:32+09:00 Document ID : uuid:44f74650-2a5a-4da6-b1e1-cf62e989a935 Format : application/pdf Title : 38289U0527F(LG) -PDP Creator : QuarkXPressª3.3E: LaserWriter 8 Z1-8.7.1 Author : PSY Producer : Acrobat Distiller 4.0 for MacintoshEXIF Metadata provided by EXIF.tools