LG Electronics USA 50PC3DUUE Plasma Display Panel User Manual 38289U0527F LG PDP

Download:
Mirror Download [FCC.gov]
Document ID	688092
Application ID	EceCg6Yg+9mmeMiSFxEVKQ==
Document Description	User Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	191.74kB (2396809 bits)
Date Submitted	2006-07-31 00:00:00
Date Available	2006-07-31 00:00:00
Creation Date	2006-07-29 10:27:47
Producing Software	Acrobat Distiller 4.0 for Macintosh
Document Lastmod	2006-07-29 10:28:23
Document Title	38289U0527F(LG) -PDP
Document Creator	QuarkXPressª3.3E: LaserWriter 8 Z1-8.7.1
Document Author:	PSY

Installation
When connecting with a component cable
DVD
(R) AUDIO (L)
HDMI / DVI IN
ANTENNA/
CABLE IN
VIDEO
AUDIO
COMPONENT IN
Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the set.
Connect the audio outputs of the DVD to the COMPONENT IN AUDIO jacks on the set.
Turn on the DVD player, insert a DVD.
Select Component 1 input source with using the INPUT button on the remote control.
- If connected to COMPONENT 2, select Component 2 input source.
Refer to the DVD player's manual for operating instructions.
AUDIO
VIDEO
Video output ports
on DVD player
22
PB
PR
Pr
Y OPTICALPb
R-YVIDEO
YDIGITAL AUDIO
B-Y S-VIDEO
OUT
Cb Cr
PB PR
AUDIO
AV OUT AV IN 1
Component ports on the TV
COMPONENT IN
• Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Installation
HDSTB Setup
- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if
you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure
as shown below.
When connecting with a HDMI cable
SERVICE
RGB IN
(PC)
REMOTE
CONTROL IN
Connect the HDMI output of the digital set-top
box to the HDMI IN 1(DVI) or 2 jack on the set.
RS-232C IN
(CONTROL & SERVICE)
SERVICE)
Select HDMI1/DVI or HDMI2 input source with
using the INPUT button on the remote control.
Turn on the digital set-top box. (Refer to the
owner’s manual for the digital set-top box.)
AUDIO IN
(RGB/DVI)
HDMI IN
1(DVI)
COMPONENT IN
AV OUT AV IN 1
Digital Set-top Box
HDMI-DTV OUTPUT
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
• TV can receive the video and audio signal simultaneously using a HDMI cable.
• If the digital set-top box supports Auto HDMI function, output resolution of the digital set-top box will
be automatically set to 1280x720p.
• If the digital set-top box does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the digital set-top box to
1280x720p.
REMOTE
CONTROL IN
When connecting with a Component cable
RS-232C IN
(CONTROL & SERVICE)
Digital Set-top Box
Connect the video
outputs (Y, PB, PR) of the digiSERVICE
RGB IN
tal set-top box to the COMPONENT
IN VIDEO
jacks on the set.
(PC)
(R) AUDIO (L)
OPTICAL
PTICAL
(PC)
DIGITAL AUDIO
OUT
Turn on the digital set-top RS-232C
box.IN (Refer to the
& SERVICE)
owner’s manual for the digital(CONTROL
set-top
box.)
Select Component 1 input source with using the
INPUT button on the remote control.
- If connected to COMPONENT 2, select
Component 2 input source.
(MONO)
S-VIDEO VIDEO
AUDIO
AV
V OUT AV
V IN 1
RGB IN
COMPONENT IN
AUDIO
VIDEO
Signal
RGBAUDIO
IN IN
REMOTE
CONTROL IN
REMOTE
CONTROL IN
Connect the audio output of the digital set-top box
to the COMPONENT
IN AUDIO jacks on the set.
HDMI / DVI IN
AUDIO IN
(RGB/DVI)
Component1/2
HDMI1/DVI, HDMI2
480i
Yes
No
480p/720p/1080i
Yes
Yes
(RGB/DVI)
RS-232C IN
(CONTROL & SERVICE)
23
SERVICE
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
HDMI / DVI IN
REMOTE
CONTROL IN
1(DVI)
RS-232C IN
(CONTROL & SERVICE)
Installation
S-VIDEO VIDEO
AUDIO
AV OUT AV IN 1
OPTICAL
DIGITAL AUDIO
OUT
COMPONENT IN
AUDIO
VIDEO
When connecting with a HDMI to DVI cable
SERVICE
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
REMOTE
CONTROL IN
HDMI IN
1(DVI)
RS-232C IN
(CONTROL & SERVICE)
SERVICE)
DVI-DTV OUTPUT
(R) AUDIO (L)
Digital Set-top Box
Connect the DVI output of the digital set-top box to the HDMI IN 1(DVI) jack on the set.
Connect the audio outputs of the set-top box to the AUDIO IN(RGB/DVI) jack on the set.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
RGB IN
(PC)
RGBAUDIO
IN IN
REMOTE
CONTROL IN
(RGB/DVI)
Select HDMI1/DVI input source with using the INPUT button on the remote control.
RS-232C IN
(CONTROL & SERVICE)
• If the digital set-top box has a DVI output and no HDMI output, a separated audio connection is necessary.
• If the digital set-top box supports Auto DVI function, the output resolution of the digital set-top box will
be automatically set to 1280x720p.
• If the digital set-top box does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the digital set-top box to
1280x720p.
24
Installation
AV Out Setup
- The TV has a special signal output capability which allows you to hook up a second TV or monitor.
AUDIO
(MONO)
S-VIDEO VIDEO
AUDIO
AV
V OUT AV IN 1
OPTICAL
PTICAL
DIGITAL AUDIO
DIGITAL
OUT
COMPONENT IN
VIDEO
Connect the second TV or monitor to the TV’s AV
OUTPUT jacks.
See the Operating Manual of the second TV or
monitor for further details regarding that device’s
input settings.
1/2
• Component 1-2, RGB-PC, HDMI1/DVI,
HDMI2, DTV input sources cannot be used
for Monitor out.
• We recommend to use the video and audio
output jacks for VCR recording.
S-VIDEO IN
(R) AUDIO (L) VIDEO
Digital Audio Output
- Send the TV’s audio to external audio equipment (stereo system) via the Digital Audio Output Optical port.
AUDIO
1/2
(MONO)
S-VIDEO VIDEO
AUDIO
AV
V OUT AV
V IN 1
OPTICAL
PTICAL
DIGITAL AUDIO
DIGITAL
OUT
COMPONENT IN
VIDEO
Connect one end of an optical cable to the TV
Digital Audio Optical Output port.
Connect the other end of the optical cable to the
digital audio optical input on the audio equipment.
See the external audio equipment instruction
manual for operation.
When connecting with external audio equipments, such as amplifiers or speakers, please
turn the TV speakers off. (Refer to p.41)
CAUTION
Do not look into the optical output port. Looking at the laser beam may damage your vision.
25
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
REMOTE
CONTROL IN
Installation
RS-232C IN
(CONTROL & SERVICE)
PC Setup
- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
When connecting with a D-sub 15 pin cable
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
Connect the RGB output of the PC to the RGB IN
(PC) jack on the set.
Connect the PC audio outputs to the AUDIO
IN(RGB/DVI) jack on the set.
Turn on the PC and the set.
Select RGB-PC input source with using the
INPUT button on the remote control.
REMOTE
CONTROL IN
RS-232C IN
(CONTROL & SERVICE)
SERVICE)
(R) AUDIO (L)
RGB-PC OUTPUT
PC
When connecting with a HDMI to DVI cable
SERVICE
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
HDMI IN
REMOTE
CONTROL IN
1(DVI)
RS-232C IN
(CONTROL & SER
SERVICE)
VICE)
DVI-PC OUTPUT
(R) AUDIO (L)
PC
Connect the DVI output of the PC to the HDMI IN 1(DVI) jack on the set.
Connect the audio outputs of the PC to the AUDIO IN(RGB/DVI) jack on the set.
Turn on the PC and the set.
Select HDMI1/DVI input source with using the INPUT button on the remote control.
RGB IN
(PC)
AUDIO IN
(RGB/DVI)
REMOTE
CONTROL IN
• If the PC has a DVI output and no HDMI output, a separated audio connection is necessary.
• If the PC does not support Auto DVI, you need to set the output resolution appropriately. To get the
best picture quality, adjust the output resolution of PC graphics card's output resolution to
1024x768, 60Hz.
RS-232C IN
(CONTROL & SERVICE)
26
Installation
1. Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.
2. When Source Devices connected with HDMI/DVI
Input, output PC Resolution (VGA, SVGA, XGA,
WXGA), Position and Size may not fit to
Screen.Press the ADJUST button to adjust the
screen Position of TV SET and contact an PC
graphics card service center.
3. When Source Devices connected with HDMI/DVI
Input, output TV SET Resolution (480p, 720p,
1080i. 1080p) and TV SET Display fit EIA/CEA861-B Specification to Screen. If not, refer to the
Manual of HDMI/DVI Source Devices or contact
your service center.
4. In case HDMI/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL"
OSD display in HDMI/DVI Input. In case that Video
Resolution is not supported TV SET output in
HDMI/DVI Source Devices, "INVALID FORMAT"
OSD display. Refer to the Manual of HDMI/DVI
Source Devices or contact your service center.
5. Check the image on your TV. There may be noise
associated with the resolution, vertical pattern,
contrast or brightness in PC, HDMI/DVI mode. If
noise is present, change the PC or HDMI/DVI
mode to another resolution, change the refresh
rate to another rate or adjust the brightness and
contrast on the menu until the picture is clear. If the
refresh rate of the PC graphic card can not be
changed, change the PC graphic card or consult
the manufacturer of the PC graphic card.
6. Avoid keeping a fixed image on the TV's screen for
a long period of time. The fixed image may become
permanently imprinted on the screen.
7. The synchronization input form for Horizontal and
Vertical frequencies is separate.
Supported Display Resolution
(RGB-PC, HDMI1/DVI, HDMI2 Mode)
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
640x350
31.468
70.08
720x400
31.469
70.08
640x480
800x600
31.469
59.94
37.879
60.31
1280x768
1360x768
47.7
60
47.7
60
1366x768
47.1
60
1024x768
48.363
60.00
Resolution
* 720x480
*1280x720
*1920x1080i
*1920x1080p
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
31.469
59.94
31.500
60.00
44.96
59.94
45.00
60.00
33.72
59.94
33.75
60.00
27.00
24.00
33.75
30.00
* This format is only for HDMI-DTV input.
27
Installation
Screen Setup for PC mode
- When RGB connect to PC input and select the RGB-PC, this function is used.
- When HDMI/DVI connect to PC input and select HDMI/DVI input, this function is used.
- After connecting RGB-PC or HDMI/DVI to PC input and checking the screen quality.
* Adjustment for screen Resolution, Position, Size, and Phase
INPUT
TV
MODE
TV
POWER
DVD
INPUT
RATIO
VCR
COMP1 COMP2
EZ PIC
HDMI
RGB-PC
EZ SOUND ADJUST
INFO
ADJUST
CC
MENU
SAP
EXIT
TIMER
Press the ADJUST button and then use D
Resolution, POSITION, SIZE, or PHASE.
Press ENTER button and then use
make appropriate adjustments.
Mini Glossary
Position This function is to adjust
picture to left/right and
up/down as you prefer.
Size
Phase
This function is to minimize
any vertical bars or stripes
visible on the screen background. And the horizontal
screen size will also
change.
This function allows you to
remove any horizontal noise
and clear or sharpen the
image of characters.
/E
button to select
D /E /F /G
buttons to
• The PHASE adjustment range is -16 ~ +16.
(In HDMI/DVI-PC mode, PHASE is not available.)
• The SIZE adjustment range is -30 ~ +30.
(In HDMI/DVI-PC mode, SIZE is not available.)
Press ENTER button.
* When you change the resolution, select the proper resolution
in present input to see the best picture appearance.
Resolution This function allows you
select
Resolution
of
XGA/WXGA.
* Initializing (Reset to original factory values)
INPUT
TV
MODE
POWER
RATIO
VCR
COMP1 COMP2
EZ PIC
TV
DVD
INPUT
HDMI
EZ SOUND ADJUST
RGB-PC
INFO
ADJUST
- To initialize the adjusted values
28
Press the ADJUST button and then use
the RESET option.
Press ENTER button and then use
Press ENTER button.
F /G
D /E
button to select
button to select Yes.
Operation
Operation
Basic operation
Turning on the TV
1. First, connect power cord correctly. At this moment, the TV switches to standby mode.
In standby mode to turn TV on, press the
, INPUT, CH D / E button on the TV or press the POWER, TV
INPUT, INPUT, CH D / E, Number (0 ~ 9) button on the remote control .
2. Select the viewing source by using TV INPUT, INPUT button on the remote control.
This TV is programmed to remember which power state it was last set to, even if the power cord is out.
3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.
Volume Adjustment
D / E button to adjust the volume.
2. If you want to switch the sound off, press the MUTE button.
1. Press the VOL
3. You can cancel this function by pressing the MUTE or VOL
button.
Channel Selection
Press the CH
or NUMBER buttons to select a channel number.
• If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
On Screen Menus Language Selection
Aspect Ratio
Aspect Ratio
Caption/Text
Caption/Text
Caption Option
Caption Option
Language
Language
ISM Method
ISM Method
Low Power
Low Power
- The menus can be shown on the
screen in the selected language.
First select your language.
Press the MENU button and then use
OPTION menu.
Press the
button and then use
English
Español (Spanish)
Français (French)
button to select the
button to select Language.
Press the G button and then use D / E button to select your desired
language. From this point on, the on-screen menus will be shown in the
selected language.
Press EXIT button to return to TV viewing or press MENU button to
return to the previous menu.
29
Operation
On Screen Menus Selection and Adjustment
How to adjust the OSD screen
1. Press the MENU button and then
2. Press the G button and then use
D /E /F /G
button to select each menu.
button to display the available menus.
EZ Scan
EZ Picture
Manual Scan
Color Temperature
Channel Edit
XD
DTV Signal
Advanced
Input Source
Video Reset
Input Label
Set ID
Lock System
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Input Block
Audio Language
Aspect Ratio
Auto Clock
Caption/Text
Manual Clock
Caption Option
Off Timer
Language
On Timer
ISM Method
Sleep Timer
Low Power
Auto Off
EZ Sound
Balance
TV Speaker
• Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
30
Operation
Setup Menu Options
EZ Scan (Channel Search)
EZ Scan
EZ Scan
Manual Scan
Manual Scan
Channel Edit
Channel Edit
DTV Signal
DTV Signal
Input Source
Input Source
Input Label
Input Label
Set ID
Set ID
Selection ( G or
leads you to the EZ
scan screen.
Processing EZ scan...
TV Ch.20
0 channel(s) found
Press
to stop the
current scan and start
DIGITAL ANTENNA channel
scan.
Next
- Automatically finds all channels
available through antenna or
cable inputs, and stores them in
memory on the channel list.
- Run EZ Scan again after any
Antenna/Cable connection changes.
- A password is required to gain
access to EZ Scan menu if the
Lock System is turned on.
MENU Previous
Press the MENU button and then use D / E button to select the SETUP menu.
Press the G button and then use
D /E
button to select EZ Scan.
Press the ENTER button to begin the channel search.
Allow EZ Scan to complete the channel search cycle for ANTENNA, and
CABLE.
Manual Scan
EZ Scan
EZ Scan
Manual Scan
Manual Scan
Channel Edit
Channel Edit
DTV Signal
DTV Signal
Input Source
Input Source
Input Label
Input Label
Set ID
Set ID
Select channel type and
RF-channel number.
TV
TV 2-0
Press
to delete the channel.
- A password is required to gain
access to Manual Scan menu if
the Lock System is turned on.
Press the MENU button and then use D / E button to select the SETUP menu.
Press the G button and then use
ber you want to add or delete.
Press the ENTER button to add or delete for the channel number.
Press the G button and then use D
/E
button to select Manual Scan.
Press the G button and then use D
and CADTV.
/E
button to select TV, DTV, CATV,
D /E
button to select channel num-
Press EXIT button to return to TV viewing or press MENU button to
return to the previous menu.
31

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 10
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:2c8ffb62-edac-4b5a-a372-839242cf8b69
Modify Date                     : 2006:07:29 10:28:23+09:00
Create Date                     : 2006:07:29 10:27:47+09:00
Metadata Date                   : 2006:07:29 10:28:23+09:00
Document ID                     : uuid:e0ef3874-2f81-4ba8-9ad0-5e6537425389
Format                          : application/pdf
Title                           : 38289U0527F(LG) -PDP
Creator                         : QuarkXPressª3.3E: LaserWriter 8 Z1-8.7.1
Author                          : PSY
Producer                        : Acrobat Distiller 4.0 for Macintosh

EXIF Metadata provided by EXIF.tools