LG Electronics USA 9QK-N41 Portable Navigation User Manual N41 MANUAL 3
LG Electronics USA Portable Navigation N41 MANUAL 3
Contents
- 1. User manual 1 of 3
- 2. User manual 2 of 3
- 3. User manual 3 of 3
User manual 3 of 3
Navigation menu Units & Time Guidance You can specify units of measure and adjust the time as displayed on your Navigator. You can select the types of voice and visual notifications that you would like to use while navigating as follows. 1. Touch 1. Touch 2. Touch the desired items. 2. Touch the desired items. : Displays and announces in kilometers. Warns you when your car exceeds the speed limit. This prompt is not active by default. : Displays and announces in miles. Displays the current local time based on GPS time in the time zone selected on your device. Activated when the Navigator recalculates a new route. This prompt is not active by default. Automatically adjusts the time when daylight saving time is in use. Note Note Languages noted with (Spoken Streets) are synthesized speeches, which have an extensive vocabulary and pronunce the street names as you approach turns, the pre recorded voices have a limited vocabulary. It is shown only in some time zones, which countries or regions adopt the daylight saving times. Language 1. Touch Warns that the GPS signal is too low and unreliable for navigation. This prompt is active by default. 2. Touch the desired items. Reminder at the start of each journey. This prompt is active by default. You can set the type of the guidance name that you will use to navigate the route. You can select the language text. You can select voice travel messages and driving directions. You can hear the voice of language through speakers while driving. 3. Touch 3. Touch 29 Navigation menu GPS Status The Navigator uses the GPS receiver to pinpoint your location. GPS signals are automatically acquired and your vehicle's location and position are constantly updated. The GPS receiver may take a few minutes to find its initial location. For best results, ensure that the GPS receiver has a clear vertical view of the sky. 1. Touch Please check that: • The GPS antenna has a clear view of the sky for uninterrupted GPS reception. The navigator cannot calculate the route if there is no GPS reception (for example, in a tunnel). • The navigation device is charged or connected to the cigarette lighter. Map Setup You can tap the “Map Setup” button to customize your map display. 1. Touch 2. Touch the desired items. The following GPS information is displayed: The angular distance east or west on the earth's surface. The location of a place north or south on the earth's surface. The rate of movement, as expressed by kilometers or miles per hour. When this option is selected, the zoom is speed dependent. The map zooms out at higher speeds, displaying a larger map area, and zooms in at slower speeds, displaying a smaller map area. If you manually change the zoom, the Automatic Zoom returns to a system defined zoom level after several seconds of inactivity. The height above sea level. You can check reception signals from the GPS satellite. Note If GPS signal can not be detected for a long time, please restart whole navigation system by pressing This option increases the size of street names to make the text easier to read. GPS not found When you first start the navigator you will hear the message “Signal too low”. This message means that your navigation device hasn’t yet located a reliable GPS signal. Check that your device is connected to the cigarette lighter and has a clear view of the sky. 3. Touch The “GPS not found” message means that there is no GPS antenna or the antenna is not properly installed. 30 Navigation menu Tutorial Select Map When you first start the Navigator, a message box appears prompting you to open the Navigator Guided Tour program. The Guided Tour is an excellent way of becoming familiar with the different navigation features available. You can also start the Navigator Guided Tour any time, by touching the “Tutorial” button from the “Extras” menu. This feature lets you change the currently selected map to another map saved on builtin memory. 1. Touch 1. Touch 2. Touch the desired items. You can touch the “Select Map” button to display the maps saved on your built in memory. The Select Map screen displays map details and version numbers. The map currently used appears at the top of the list. : Lets you refresh the screen when a new memory card is inserted into the device. Help You can display Navigator technical support information. Touch : Lets you permanently remove a selected map. Note You cannot delete the current map. Select lets you designate a selected map as the current map. Initialise Start Demo 1. Touch This lets the Navigator display a simulated route. Many of the navigation features are disabled when the Demo is running. Touch Touch to end the Demo. Note You can delete all list from the memory. The demo route is set, and depending on the current map data, the demo function may differ somewhat from the map data. You can set all the function to their factory settings. 2. Touch 31 Music player Playing music Playing the files in “All Music” folder 3. Touch and then touch the desired file to play music in “My Music” folder. 1. Touch > . The “Music List” screen appears. There are two kinds of music list: All Music, My Music on the screen to move to the • Touch previous/next page. 2. Touch the folder or file you want to play. on the screen to move to the • Touch upper folder. on the screen to move to the • Touch previous screen. Note Playing the files in “My Music” folder If there is no supported file, an error message is displayed on the screen and the next music file will be played. 1. Touch during playback. The mark indicates playing music file. 2. Touch in the left position of the screen. The mark appears and the file you touch is stored in “My Music” folder. To cancel it, touch 32 Music player Pause 1. Touch during playback. 2. To return to playback, touch Viewing the information of music file again. Skip the next music Touch briefly to move to the next music. 1. Touch during playback. The information of music file appears. (If you touch the information screen, it moves to the previous screen.) Skip the previous music Touch briefly music. to move to the previous Search Touch and hold the or during playback and then release at the point you want. You can use the slide bar to search for the music. Repeat You can set the repeat playback mode by touching or . If there is no information of music file, appears. Adjusting the Volume/Brightness 1. Touch during playback. The “Handy Setup” screen appears. 2. Set the volume ( ) and brightness ( ) by touching and then touch . : Plays repeatedly the current selected file. : Plays repeatedly all music files in your device. Shuffle Mute Touch on the “Handy Setup” screen to mute the sound .To cancel it, touch again. You can set the random playback mode by touching or : Returns to the normal playback. : Plays randomly all the files in your device. 33 Photo viewer Viewing photo 1. Turn the unit on. The map screen appears. 2. Touch The “Photo List” screen appears. on the screen to move to the • Touch upper folder. on the screen to move to the • Touch previous screen. Pause 1. Touch the screen during slide show. 2. Touch to pause slide show. 3. To return to slide show, touch again. Skip to the next photo 3. Touch the folder or file you want to play and then touch The slide show starts automatically. Touch to move to the next photo in the selected folder. Skip to the previous photo Touch to move to the previous photo in the selected folder. Repeat You can set the repeat playback mode by touching or . Browse an image 1. : Plays repeatedly all photo files in your device. Touch the screen during slide show and then touch : Plays repeatedly all the photos within folder. Rotation Press repeatedly to rotate the photo clockwise. 2. Touch the folder icon to display its subfolders and thumbnail images. Adjusting the Volume/Brightness 1. Touch during playback. The “Handy Setup” screen appears. 2. on the screen to move to the • Touch previous/next page. 34 Set the volume ( ) and brightness ( ) by touching and then touch . Bluetooth (Optional) Bluetooth wireless technology If you have a phone with Bluetooth wireless technology and it is compatible with your device (Please refer to the list of available phones on the page 48-50), you can use the following features in your device: Hands-free Calling, Audio streaming for mp3, and Phonebook sync and edit. Hands free feature is to make or receive a phone call using microphone and speaker built in your device. Audio streaming feature is to enable to listen to music (especially, mp3 file) in your stereo headset and to enable to handle playing music such as play, pause, or skip. Lastly, phonebook sync and edit feature is to transfer your phonebook in your phone to your device, and to add and edit new phone numbers on your device. These features on your device are only available if your phone supports these features using Bluetooth wireless technology. To use these features, you must connect your phone with your device. You may initiate this connection from your phone or from your device. Please refer to phone’s guidebook for more information. Connecting your unit and bluetooth phone To connect using the unit settings 1. Press POWER ( ) briefly in power on status. The “Handy Setup” screen appears. Map/Photo mode 2. Touch 3. Touch 4. Touch The “Searching for available devices.” pop-up screen appears on the screen. It will take about 30-60 seconds, to continue the process. To cancel, touch 5. Touch a bluetooth phone you desire from the “Search Results” screen. The “Please enter the below PIN code in your phone” pop-up screen appears. 6. Input the PIN code (0000) in your phone when the pop-up screen is displayed on the screen. When it is successfully connected, the mark is displayed in the "Handsfree available devices" screen. When it is not connected, the connection failure message appears. Music mode Note Before connecting, check the PIN code settings. Refer to “Setting the Bluetooth” on the page 36. 35 Bluetooth (Optional) To connect using the phone settings Your phone’s Bluetooth feature may be set to off by default. To use the Bluetooth feature, Bluetooth must be turned on in your phone. Refer to your phone’s user guide. Disconnecting/Deleting/Connect -ing again the bluetooth phone 1. Touch the connected phone. And then touch 1. Enable the phone’s Bluetooth component. This might be in a menu called Settings, Bluetooth, Connections, or Hands-free. 2. Initiate a search for Bluetooth devices. These settings might be located in a menu called Bluetooth, Connections, or Handsfree. Touch and the . Your phone is disconnected mark disappears. 3. Select the your device from the list of phone. 4. Input the PIN code (0000) in your phone. When it is successfully connected, the mark is displayed in the "Handsfree available devices" screen. 2. Touch the disconnected phone again to connect again or delete your phone. Setting the Bluetooth You must select to connect successfully your unit and bluetooth phone. 1. 2. 3. Touch in the “Handsfree available devices” screen. And then touch When you touch , the disconnected phone is connected again to the unit. The mark appears again. Check the PIN code. Change the PIN code using the number buttons if you want to change the PIN code. And then touch If the visibility option has set as Other Bluetooth devices can’t find your device. When you touch phone is deleted. 36 , the disconnected Bluetooth (Optional) Making a call with phone number Storing the phone number Connect your unit and bluetooth phone before you make a call. 1. Input the phone number in the “Dial” screen. And then touch 2. Input the name. And then touch It is stored in the phone book. 1. Press POWER ( ) briefly. And then touch 2. Input the phone number you want to call, by touching the number buttons. And then touch Adjusting the Volume/Microphone level 1. Touch during a call. The “Volume & Microphone” screen appears. 2. Set the volume ( ) and microphone level ( ) by touching and then touch . Note • If you make a mistake while dialling, touch to erase one digit at a time. • Touch if you want to store the phone number. It is stored in the phone book. 3. Touch to finish the telephone conversations. Note • Touch to cut the microphone sound .To cancel it, touch again. • If there is not any touch for about 5 seconds, the screen moves to the previous screen. Switching the sound path during a call You can hear sound through the speaker of unit or phone by touching / . If you want to store the phone number, touch , then input the name using key board. And then touch and it is stored in the phone book. Touch if you want to make a call again. If there is not any touch for about 10 seconds, the screen moves to the “MENU” screen. Note If you want to send the touch tones, touch 37 Bluetooth (Optional) Call History Adding the phone number Your unit keeps a record of your recently received and dialling calls. 1. Press POWER ( ) briefly. And then touch 1. Touch in the “Phone Book” screen. And then Touch after inputting the number buttons. 2. Touch 2. Touch the list you want to call. And then touch after changing the name. Receiving all list in your phone Using your phone book 1. in the “Phone Book” screen. And Press POWER ( ) briefly. And then touch 2. Touch then touch Touch the list you want to call. And then touch - Your device will receive the contact(s) via Bluetooth in your phone. If your phone is not connected, it needs to enter the PIN code in the phone. - With receiving phone book from your phone, and the data will be stored in the resident memory of your device. 38 Bluetooth (Optional) Getting all list from you phone Deleting the phone number If your phone supports the synchronization of phone book, you can get all list from the phone. Touch the list to delete in the “Phone Book” screen. And then touch * If the phone hasn't been registered to available list on your device, you will meet the below pop-up, "Do you want to get the phonebook from your phone?", after connecting your phone with the your device. Editing the phone number Touch then touch 1. Touch the list to edit in the “Phone Book” screen. And then touch 2. Touch after changing the number. And then touch after changing the name. in the “Phone Book” screen. And The synchronisation with your phone book will begin automatically, the data will be stored in the resident memory of your device. (It will takes a few minutes according to the number of phone book in your phone.) Deleting all list in the phone book 1. Touch in the “Phone Book” screen. And then touch Using voice Dial You can make a call by speaking the contact’s name. 1. Press POWER ( ) briefly. And then touch 2. Touch 39 Bluetooth (Optional) 2. Speak the contact name from your phone. And then speak name, number or command. Listening to music files You can control and hear the music (especially, mp3) files saved on your device via the your stereo headset with Bluetooth wireless technology. Touch in the “Handy Setup” screen. 3. Touch to finish the telephone conversations. Incoming calls 1. If there is an incoming call, your phone rings and the “Call from” pop-up screen is displayed on the screen. 2. Touch to answer the call. If you want to reject a call, touch Notes • You can hear the sound through the speaker of unit or Bluetooth stereo headsets by touching / . • The sound quality depends on Radio Frequency (RF) conditions and the sampling rate of audio. • Sampling rate of MP3 file that can hear the music using Bluetooth stereo headset - 16 KHz , 32 KHz , 44.1 KHz , and 48 KHz - The sound quality may be poor on the sampling rate of 16 KHz , 32 KHz. Ending calls When you are calling on the map, music, or photo mode, appears in the screen. Touch to finish the telephone conversations. Music mode Map mode Photo mode 40 Installation Installing the Navigator “PC Portal” Installation the Microsoft .Net Framework 2.0 for computer can be done by following the instructions. 1. Insert the Navigator CD into the PC's CDROM drive. The “PC Portal” Installation wizard prompts you to select the language used for the installation process. When you have selected a language, click “OK”. 2. Read the Welcome message and click “Next”. 3. From the Select Directory screen, either accept the recommended default directory or browse to a different directory to install the “PC Portal”. Click “Next”. 4. If you want to change the directory location before installing, click “Back”. When you are ready to install the “PC Portal”, click “Next”. The installation status box displays the progress of the installation process. 9. Select from up to two connected devices. (LN830/LN835/LN835R) Note Please pay close attention to all the programs before installing the CD to your personal computer. Please pay close attention especially for antivirus programs like spyware. Recommended PC System Requirements Please review the following system requirements before installing “PC Portal”: • CPU: AMD/Intel® Processor 300 MHz or faster • Operating System: Windows® 2000/XP/Vista • Memory: 128 MB RAM (minimum) • Hard drive free space: 500 MB (minimum) • CD-ROM: 4x drive or higher • ActiveSync Version 3.8 to 4.2 supported under Windows 2000 and XP • USB Version 1.1 or 2.0 connection (compatible 2.0) • Microsoft .Net Framework 2.0 5. When the installation is complete, click the “Finish” button. 6. After finishing installing PC Portal, install the “Maps installer’ program. This procedures is simillar to PC Portal install. 7. When the installation is complete, click the “Finish”button, The Select Language box appears. 8. From the Select Language dialog box, you can select the display language for the “PC Portal”. Select the Launch “PC Portal” checkbox for “PC Portal” to immediately start and click “OK”. Alternatively, you can start the “PC Portal” from the Microsoft® Windows® Programs menu. 41 Installation/Using software Starting the “PC Portal” Wizard Using the “PC Portal” The first time you start the “PC Portal”, the “PC Portal” Wizard automatically starts, letting you install navigator software, supported languages and voice prompts, and maps. For a complete description of the “PC Portal”, see Using the “PC Portal” on the page 42-43. 1. Click the Microsoft® Windows® Start button. 2. Click the Programs > LGE > “PC Portal”. The “LGE PC Portal for (LN840/LN840R/ LN845/LN845R/LN855/LN855R)” appears. 3. If this is your first time using “PC Portal”, the “PC Portal” wizard automatically starts and displays the Welcome screen. 4. Make sure that your device is connected by USB cable to a port on your PC. You will see Connected on the “PC Portal” screen. 5. Click the buttons to move to the previous or next screen. 6. Select software components to install to your device. Note • If you want to start the wizard, click from the “PC Portal” Main screen. • If you want to stop the wizard, click The “PC Portal” Main screen is displayed. • If after selecting component, software, and voice options, you want to return to the original selections, click Click “Install Software” and select from the following components to install to your device: • LGE: GPS navigation software • Tutorial: Tutorial guide To install navigator components: 1. From the Install Software screen, select from the list of components, as described above. 2. Click the Install button. 3. Navigator “PC Portal” installs the selected components to the device’s main memory. Click “Manage Maps” to install or remove a map. For more information, see “Installing Maps” on the page 44. Click the “User Manual” button to see a user manual. Click the “Select Language” button to show a list of languages that you can choose from to display the “PC Portal”. Click the “About” button to check software version. 42 Using software Click the “Backup/Restore” button to backup the following Navigator items: • Favorites: All locations that are displayed in Navigator’s Favorites screens. • Trips: All locations that appear in Navigator’s Multistops screens. • LGE Settings: Setting configurations, such as map views (2D/3D and Day/Night), prompts, units of measurement, and map and route setting preferences. When you select Backup, “PC Portal” makes a copy and stores the information to your computer. To backup Navigator data to your PC: 1. From the Backup/Restore screen, select Backup. 2. Select the items that you want to make a copy of and save to your computer. 3. Click the “Backup” button. 4. “PC Portal” saves the selected items to your computer. Click Install Languages to install a language to your device. To install languages: 1. From the Install Languages screen, select the languages to be installed to the device. 2. Click the Install button. 3. Navigator PC Portal installs the selected languages to the device’s main memory. 4. You can display the Navigator interface in the language of your choice by tapping the Language Settings button on the Setup menu and selecting the language in Navigator. Click the Backup/Restore button to restore Favorites, Multistops, and My Navigator data to a navigation device. When you select Restore, “”PC Portal” recovers the information stored on your computer. To restore stored Navigator data to a navigation device: 1. From the Backup/Restore screen, select Restore. 2. Select the items that you want to restore. 3. Click the “Restore” button. 4. “PC Portal” restores the selected items. 43 Using software Installing Maps Removing Maps You can remove a map by selecting a map in the Device Maps pane and clicking the “Add/Remove” button. 1. From the Desktop Maps pane, select a map. 2. From the “Target” context box, select the main memory. 3. When you select a Target option (Storage Card, Main Memory) the “PC Portal” displays the following information: • Required: The amount of free space necessary to install the map on the selected Target option. • Available: The amount of free space available for the selected Target option. Note: If the free space required is equal or greater than the free space available, “PC Portal” will not install the selected map. 4. Select a map to add or remove. 5. Click the “Add/Remove” button. 6. The selected map is installed and displayed in the Device Maps panel. 44 Using software General Warning Messages The following warning messages can appear when you’re working with navigator “PC Portal”. Lost connection transfer If at any point during the installation or data transfer, the connection to the device is lost, the following message is displayed: "Connection to the device has been lost. Please check your connection." Uninstalling Navigator Console When a version of navigator programme (versions prior to the “PC Portal”) is located on your computer, the following message is displayed: "A previous version of “PC Portal” was found. Do you wish to uninstall?" It is recommended to uninstall the previous progam before installing “PC Portal”. Uninstalling “PC Portal” When an earlier version of navigator “PC Portal” is located on your computer, the following message is displayed: "A previous version of “PC Portal” was found. Do you wish to uninstall? " It is recommended to uninstall a previous version of “PC Portal” before installing the current version. Previous maps If maps from a previous version are located on your computer, the following message is displayed: "Existing maps data found. Do you want to keep it?" Clicking “Yes” lets you install maps from previous versions. Remove maps The following message appears when you have selected an installed map and clicked the Actions button: "Selected maps shall be removed from your device. Are you sure you wish to continue?" Data Transfer If you close the PC Portal while install navigator software, a map, importing or exporting a Favorite location, or backing up data. the following message appears. : “if you will close the PC Portal now, the [process] shall not be completed. Are you sure you wish to close?”. Backup Data If stored data is located on your computer, the following message appears: "Navigator Backup data found. Do you want to keep it?" It is recommended to keep backup data. Updates to “PC Portal” If there are updates in navigator, you are prompted to download them in the following message: "There are updates to “PC Portal”, do you wish to download and install them?" 45 Troubleshooting Navigation program and map data protection “Guidance” in “Setup”. But during actual driving, the voice guide is provided. If the volume is too low, adjust the volume on the right unit. • If you want to operate this product properly, navigation program and map data provided by LGE should be in LGE folder on your navigation device. • Don't erase or modify any contents in the LGE folder using USB mass storage connection. (All contents are important to operate navigation. Deleting this data may cause navigation to lead to malfunction.) Cannot see the map. This is when you cannot see the map even when you have executed the navigation menu. This happens when the data within the memory is damaged. Delete all the data within the memory and reinstall the data. If the problem persists after the installation, contact the Customer Service Center. Audio streaming To enjoy high quality music using Bluetooth stereo headsets, we recommend over 16-bit audio with sampling rates of 48 KHz and 44.1 KHz. (The sound quality depends on sampling rates of audio and your headset.) Map data and dangerous area information are not updated. You must periodically update the map data. Refer to the homepage for details on how to update the data. Picture format JPG: Image file size should be less than 1600 MP (megapixels). The path guide can be different from the actual path. (Path guide error) Cannot identify the current location. (GPS not receiving) GPS cannot be used indoors and must be connected to the power with ACC to a vehicle in a location where the sky can be seen well. When initially connecting the GPS, it usually takes about 10 minutes to operate normally, but the connection speed can differ depending on the weather condition, and surrounding obstacles. If the GPS connection is unstable for a long period of time, try the following. • Check if the power is connected to the product. • Check if the back of the GPS product is in a location where the sky can be seen well. • If there are high buildings or if you are under a tree, move to a location where there aren’t any obstacles. • Check the GPS receiving condition from the GPS menu. • When the road is closely parallel. • When the splitting road angle is very small. • When there is an adjacent road when turning. • When driving on a road that is narrowing fast. • When driving through the mountain or where the road is too curvy. • When the starting, passing and arriving locations are too close within 10 km. • When you have set the starting, passing or arriving location more than 1 km away from the road. • When driving through the tunnel. • When driving through high buildings. Cannot hear the voice guide. You can hear the voice guide when you select 46 Troubleshooting There is a difference between the driving road and the road on the map in the product. Even though GPS is usually very accurate, it has an error range. When GPS receiver is installed, there can be an error of about 5 to 15m. But for newly constructed roads, the problem could be from the data update to the map. What is GPS? The Global Positioning System (GPS) is a satellite-based navigation system made up of a network of 24 satellites placed into orbit by the U.S. Department of Defence. GPS was originally intended for military applications, but in the 1980s, the government made the system available for civilian use. GPS works in any weather conditions, anywhere in the world, 24 hours a day. There are no subscription fees or setup charges to use GPS. GPS GPS Map matching The GPS used by this Mobile Navigation System is susceptible to certain errors. Their calculations may on occasion place you in a location on the map where no road exists. In this situation, the processing system understands that vehicles travel only on roads, and is able to correct your position by adjusting it to a near road. This is called map matching. With map matching. GPS GPS With no map matching. Basic operation tips 1. After charging or connecting to a power source, turn the unit on. 2. Make sure you are stopped (not moving) in a location with a clear view of the sky. 3. You will see your current location within a few minutes and then you can start navigating. 4. If the correct location is not found within 6 minutes, restart the unit using the ON/OFF button on the side of the unit. 47 Bluetooth phone compatibility list • If even a phone as described in this list meets requirements of Bluetooth Hand-free Profile 1.5 and Object Push Profile 1.1, it can operate. However, it is noted that we cannot assure for operation by function. • As difference in functional operation by model is mainly resulted from feature of a hand-free phone, consult manufacturer of a phone if you have any question. • There may be restrictions on using Bluetooth technology depending on some locations or wireless environment. Due to the variety of Bluetooth phones and their firmware version, your device may respond differently when performing over Bluetooth. Manufacturer Model Year Hansfree Display Voice Phone Book Object Push Calling Caller ID Dial Sync (vCard) BLACK BERRY BLACK BERRY HP HP LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG MOTOROLA MOTOROLA MOTOROLA MOTOROLA MOTOROLA MOTOROLA MOTOROLA MOTOROLA MOTOROLA MOTOROLA MOTOROLA MOTOROLA MOTOROLA MOTOROLA MOTOROLA MOTOROLA NOKIA NOKIA NOKIA NOKIA 8100 8800 HW6915 H6315 KE970 KE850 CU500 ME970 MG320 MG280 KE500 KG290 KU380 CU575 KU580 KU970 KG245 KG800 M4410 U890 U6 RIZR Z80 ROKR E6 RAZR V3i V360 KRZR K1 ROKR E2 SLVR L7 V195 V600 RAZR V3X E1000 A1000 E550 V525 V600 6230i 6230 8910i N77 2007 2007 2005 2007 2007 2007 2007 2007 2007 2007 2007 2007 2007 2007 2007 2007 2006 2006 2006 2006 2006 2007 2007 2006 2006 2006 2006 2006 2006 2006 2006 2005 2004 2004 2004 2004 2005 2004 2004 2007 YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES NO YES YES YES NO YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES 48 YES YES NO NO NO NO NO NO NO NO NO NO NO YES NO NO NO NO NO NO YES NO NO YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES NO YES NO NO YES NO NO YES NO YES NO NO NO NO NO NO NO NO NO NO NO NO YES NO NO YES YES YES NO YES YES YES YES YES NO YES YES YES YES NO YES NO NO NO YES YES YES NO YES NO YES YES YES YES YES YES YES NO YES YES YES NO NO YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES Bluetooth phone compatibility list Manufacturer NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA NOKIA PALM PALM PANTECH SAMSUNG SAMSUNG SAMSUNG SAMSUNG SAMSUNG SAMSUNG SAMSUNG SHARP SIEMENS SIEMENS SIEMENS SIEMENS Model Year Hansfree Display Voice Phone Book Calling Caller ID Dial Sync N95 2007 YES YES YES NO N91 2007 YES YES YES NO 8600 2007 YES YES YES YES N91 2007 YES YES YES NO N91 2007 YES YES YES NO 6103 2006 YES YES YES YES 6131 2006 YES YES YES YES 7370 2006 YES YES YES YES 7380 2006 YES YES YES YES 6280 2006 YES YES YES YES E60 2006 YES YES YES NO E61 2006 YES YES YES NO N70 2006 YES YES YES NO 5300 2006 YES YES YES YES 5500 2006 YES YES YES NO 6670 2006 YES YES YES NO E50 2006 YES YES YES NO E62 2006 YES YES YES NO E70 2006 YES YES YES NO N73 2006 YES YES YES NO N80 2006 YES YES YES NO N92 2006 YES YES YES NO 6670 2005 YES YES YES NO 3230 2005 YES YES YES NO 6680 2005 YES YES YES NO 7610 2004 YES YES YES NO 9500 2004 YES YES NO NO 3650 2004 YES NO YES NO 6600 2004 YES YES YES NO 6820a 2004 YES YES YES NO N-GAGE 2004 YES YES YES NO 6650 2004 YES YES YES YES TREO750V 2007 YES YES NO NO TREO750V 2007 YES YES NO NO PG6200 2006 YES YES NO NO D900 2007 YES YES NO YES i600 2007 YES YES YES NO A707 2007 YES YES NO NO D600 2006 YES YES NO NO D820 2006 YES YES NO NO Z540V 2006 YES YES NO NO T509 2006 YES YES NO NO GX15 2004 YES NO NO NO SL75 2006 YES YES NO YES SK65 2004 YES YES NO YES SX1 2004 YES YES YES NO S65 2004 YES YES NO YES 49 Object Push (vCard) YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES NO YES YES YES YES YES YES YES YES YES NO NO YES YES NO YES YES YES YES YES YES Bluetooth phone compatibility list Manufacturer Model SONY SONY SONY SONY SONY SONY SONY SONY SONY SONY SONY SONY V800 M600i K750i W810i V600i W710i W850i K800i K700i S700i T610 Z600 Year Hansfree Display Voice Phone Book Calling Caller ID Dial Sync 2005 YES YES YES YES 2007 YES YES YES YES 2006 YES YES YES YES 2006 YES YES NO YES 2006 YES YES YES YES 2006 YES YES YES YES 2006 YES YES YES YES 2006 YES YES NO YES 2005 YES YES YES YES 2005 YES YES YES YES 2004 YES YES YES YES 2004 YES YES YES YES 50 Object Push (vCard) YES YES YES YES YES YES YES YES YES YES YES YES Specifications ITEM SPECIFICATION REMARK OS CPU MEMORY Win CE 5.0 ARM9 400 MHz 2GB Built-in Memory DISPLAY 4.3 inch TFT LCD Resolution 480 X 272 LED type Backlight Touch Screen Analog resisitive type Mono, Internal Speaker Typical 1.0W (1EA) AUDIO GPS SiRF star III, Internal Antenna NAVI North America [TMC: FM Traffic Receiver (Optional)] MAP Navteq POWER TEMPERATURE Built-in BATTERY DC 5V/1A Voice Guidance Vehicle Power Cigar-jack Input (12-24V) Operating : -10 °C to 60 °C Storing : -30 °C to 80 °C DC 3.7 V (Li-Ion), 1100mAh - MP3: 4 hours [Brightness: Minimum, Volume: 5 (Center)] - Navigation: 3.5 hours [Brightness: 5 (Center) , Volume: 5 (Center)] - Photo: 4 hours [Brightness: 5 (Center) , Volume: 5 (Center)] INTERFACE Mini-USB Port External GPS Jack USB 2.0 Multimedia Image Audio JPG MP3 51 Bluetooth “The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by LG Electronics is under license. Other trademarks and trade names are those of their respective owners.” P/N: AFN32793967-1
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2008:02:20 06:50:40-08:00 Modify Date : 2008:02:20 06:50:40-08:00 Page Count : 24 Creation Date : 2008:02:20 14:50:40Z Mod Date : 2008:02:20 14:50:40Z Producer : Acrobat Distiller 5.0.5 (Windows) Author : ltsai Metadata Date : 2008:02:20 14:50:40Z Creator : ltsai Title : N41_MANUAL-3.pdfEXIF Metadata provided by EXIF.tools