Leidos 418M1 RTR-4 Wireless Option User Manual RTR 4 WSCover

Science Application International Corporation RTR-4 Wireless Option RTR 4 WSCover

18 throug 21

RTR-4 Portable Digital X-Ray Imaging System--Operator’s Manual Supplement 306847 Rev A SAIC Proprietary 4-33Insert one end of the Power/Transceiver’s “Imager” coaxial cable into the blue labeled “Imager” jack on the right-hand end of the Power/Transceiver and the other to the appropriate jack on the Imager.4Power up the Power/Transceiver by pressing its On/Off rocker switch to the On position as shown below. The red “POWER” LED to the right of the switch should illuminate. NOTEIf the “POWER” LED fails to illuminate, replace the Power/ Transceiver battery in accordance with the procedure in Chapter 6. If it still fails to illuminate, replace the Power/Transceiver.STEP ACTION
RTR-4 Portable Digital X-Ray Imaging System--Operator’s Manual Supplement4-4 SAIC Proprietary 306847 Rev AX-ray Receiver SetupConnecting the X-ray ReceiverX-ray Receiver Connection DescriptionThe X-ray Receiver must be Velcro-mounted on the XR200 X-Ray source and its cable connected to the source in order for the XR200 to transceive commands to and from the Power/Transceiver.PrerequisitesThe Connecting the Power/Transceiver procedure must have been completed.Connecting the X-ray ReceiverThe X-ray Receiver is connected to the XR200 as followsSTEP ACTION 1Remove the X-ray Receiver from the packing case. Screw in its supplied antenna and attach single X-ray Receiver cable into the X-ray Receiver’s socket near the antenna as shown below2Attach the X-ray Receiver to the XR200 via its rear-mounted Velcro strip.
RTR-4 Portable Digital X-Ray Imaging System--Operator’s Manual Supplement 306847 Rev A SAIC Proprietary 4-53Insert the other end of the X-ray Receiver’s cable to the appropriate socket in the XR200 as shown below:4Power up the X-ray Receiver by sliding its On/Off switch to the On position as shown below. The green LED next to the switch should illuminate. NOTEIf the green LED fails to illuminate, replace the X-ray Receiver battery in accordance with the procedure in Chapter 6.STEP ACTION
RTR-4 Portable Digital X-Ray Imaging System--Operator’s Manual Supplement4-6 SAIC Proprietary 306847 Rev AWiFi NIC SetupWiFi NIC Setup DescriptionThe Orinoco WiFi NIC must be properly installed and configured in the CU-4/NCU in order for the Wireless Option to function properly. Both CU-4 and NCU procedures are shown as required.PrerequisitesThe Power/Transceiver Setup and X-ray Receiver Setup procedures must have been completed.WiFi NIC Setup ProcedureThe WiFi NIC is installed and configured as follows:STEP ACTION1Carefully insert and seat the WiFi NIC into the respective CU-4 PCMCIA slot located on the left side of the computer as shown below.Carefully insert and seat the WiFi NIC into the respective NCU PCMCIA slot located on the left side of the computer as shown below.
RTR-4 Portable Digital X-Ray Imaging System--Operator’s Manual Supplement 306847 Rev A SAIC Proprietary 4-7Optional Extended-Range Antenna InstallationOptional Extended-Range Antenna InstallationThe Extended-Range Antenna is not required for wireless operation, but when used, increases the system’s signal strength and effective operating range. Both CU-4 and NCU antenna installation procedures are shown.PrerequisitesThe WiFi NIC Setup procedure must have been completed.Extended-Range Antenna Installation ProcedureThe Extended-Range Antenna is installed and configured as follows:STEP ACTION1Remove the small black antenna cable slot cover on the left side of the NIC. Stow the cover in a safe place.Carefully insert and tighten the antenna cable’s L-shaped brass connector onto the antenna extension cable. Then carefully insert and seat the flat connector on other end of the cable into the WiFi NIC card slot in the CU-4 or NCU respectively as shown in the figures below.

Navigation menu