Mertik Maxitrol and KG B6RHAS Control Unit For GV60/Symax System User Manual Users manual Part 2 of 3

Download:
Mirror Download [FCC.gov]
Document ID	4190174
Application ID	suxfYzCZXouc89vnBcXLQA==
Document Description	Users manual Part 2 of 3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	319.94kB (3999190 bits)
Date Submitted	2019-03-05 00:00:00
Date Available	2019-03-06 00:00:00
Creation Date	2018-11-21 13:19:34
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2019-01-28 16:28:42
Document Title	Users manual Part 2 of 3
Document Creator	Adobe InDesign CC 13.1 (Macintosh)
Document Author:	© Mertik Maxitrol GmbH & Co. KG

DRAFT 21/11/2018
MODES OF OPERATION
AM
PM
ON
OFF
1 2
AM
PM
ON
OFF
Thermostatic Mode
 he room temperature is measured and
compared to the set temperature. The
flame height is then automatically adjusted to achieve the set temperature.
FOR OEM USE ONLY
PROGRAM MODE
AM
PM
AM
AM
PM
ON
OFF
ON
OFF
OFF:
1.	Press
or
or
button to enter
Manual Mode.
2.	Press button to enter Thermostatic
Mode.
Default settings:
ON TIME (Thermostatic) TEMPERATURE: 70 °F / 21 °C
OFF TIME TEMPERATURE: “ ” (pilot flame only)
ON
OFF
AM
PM
or
NOTE: The set temperature for Thermostatic Mode is the temperature for the ON time in Program Mode. Changing
the Thermostatic Mode set temperature also changes
the ON time temperature in Program Mode.
AM
PM
THERMOSTATIC MODE
or ,
ON
OFF
1 2
Eco Mode
Flame height modulates between high
and low. If the room temperature is lower than the set temperature, the flame
height stays on high for a longer period
of time. If the room temperature is higher than the set temperature, the flame
height stays on low for a longer period
of time. One cycle lasts approx. 20 min.
1 2
Program Mode
PROGRAMS 1 and 2, each can be programmed to go ON and OFF at specific
times at a set temperature.
1 2
ON:
Press
button.
displayed.
1 2
ON:
Press
button. displayed, preset temperature displayed briefly, and then room
temperature displayed.
TEMPERATURE SETTING:
1.	Press
button and hold until
flashes.
and set temperature (setting in Thermostatic Mode) displayed.
2.	To continue press
button or wait.
displayed, temperature flashes.
3.	Select OFF temperature by pressing
the
or
button.
4.		To confirm press
button.
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
1 2
OFF:
1. Press
button.
2. Press or button to enter Manual
Mode.
3. Press button to enter Program Mode.
4. Press
button to enter Eco Mode.
NOTE: The ON (Thermostatic) and OFF set temperatures are
the same for each day.
AM
PM
AM
PM
ON
OFF
1 2
SETTING:
1.	Press
button and hold until displayed, temperature flashes.
2.	To adjust set temperature press
or
button.
3. To confirm press
button or wait.
ON
OFF
1 2
DAY SETTING:
5. 
flashes. Press
or
button to
choose between
, , , , ,
, , .
6.	To confirm press
button.
15 / 29
ENGLISH
INSTALLATION AND OPERATING INSTRUCTIONS
INSTALLATION AND OPERATING INSTRUCTIONS
DRAFT 21/11/2018
AUXILIARY FEATURE (2ND BURNER FEATURE)
selected
AM
PM
ON
OFF
1 2
FOR OEM USE ONLY
ON TIME SETTING (PROGRAM 1):
7.	 , ,
displayed,
is displayed
shortly, and hour flashes.
	 8. To select hour press
or
button.
9.	To confirm press
button.
, ,
displayed,
displayed shortly,
and minutes flash.
10.	To select minutes press or button.
11. To confirm press
button.
The latching solenoid valve will open automatically after ignition
or after switching the system off, so that the maximum flow of
gas is supplied to both burners assisting with the ignition process. After pressing the AUX-button the motor will turn 7 seconds in the ON direction until the max. position is reached.
AM
PM
ON
OFF
AM
PM
ON
OFF
1 2
but-
OFF:	
To switch the burner OFF, press the
button. disappears.
1 2
OFF TIME SETTING (PROGRAM 1):
12.	 , ,
displayed,
is displayed
shortly, and hour flashes.
13.	To select hour, press or button.
14.	To confirm press
button.
, ,
displayed,
displayed shortly, and minutes flash.
15.	To select minutes press or button.
16. To confirm press
button.
ON:
To switch a burner ON, press the
ton. displayed.
NOTE: The latching solenoid valve cannot operate manually. If
the receiver battery runs down it will remain in the last
operating position.
ECO MODE
NOTE: Either continue to PROGRAM 2 and set on and off times
or stop programming at this point, and PROGRAM 2 remains deactivated.
AM
NOTE: PROGRAM 1 and 2 use the same ON (Thermostatic) and
OFF temperatures for
and Daily Timer ( , , ,
, , , ). Once a new ON (Thermostatic) and / or OFF
temperature has been set, that temperature becomes the
new default setting.
NOTE: If
or Daily Timer are programmed for PROGRAM 1 and PROGRAM 2 ON and OFF times, these
become the new default times. The batteries must be removed to clear the PROGRAM 1 and PROGRAM 2 ON
and OFF times and temperatures.
ON:
Press
button to enter Eco Mode.
displayed.
OFF:
Press
button.
disappears.
MYFIRE APP
NOTICE
▪ Set ON time and OFF time using same procedure as “
selected” (above).
▪
: Set ON time and OFF time for both Saturday and Sunday.
▪D
 aily Timer: Unique ON and OFF times may be set for a single
day of the week, for multiple days of the week, or for every day
of the week.
▪ Wait to finish setting.
Before the app can be used, the myfire Wi-Fi Box must be wired
and plugged into mains power according to myfire app setup
diagram (see figure 30, page 29), and the app setup must be
completed (see myfire app setup, page 24).
AM
PM
ON
OFF
1 2
If Thermostatic, Program or Eco Mode
is activated, the corresponding icon and
“ ” is displayed on the handset.
The modes can be operated according
to the descriptions on previous pages.
NOTE: In Manual Mode “ ” is NOT
displayed on the handset.
16 / 29
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
or Daily Timer ( , , , , , , ) selected
DRAFT 21/11/2018
INSTALLATION AND OPERATING INSTRUCTIONS
FOR OEM USE ONLY
10-SYMBOL OPERATION
Child Proof
Time
Signal Indicator
Thermostatic Mode
Battery Status
AM
PM
ENGLISH
Fan
Countdown Timer
Fahrenheit or Celsius
Program Mode
Light
ON
OFF
1 2
Eco Mode
Temperature
Auxiliary Feature (2nd Burner Feature)
Figure 22: 10-symbol Display
SETTING FAHRENHEIT OR CELSIUS
AM
PM
To change between °C and °F, press
and
buttons simultaneously.
NOTE: C
 hoosing °F results in a 12 hour
clock. Choosing °C results in a
24 hour clock.
ON
OFF
1 2
CHILD PROOF
AM
PM
ON
OFF
1 2
ON:
To activate press
and
buttons
simultaneously.
displayed and the
handset is rendered inoperable, except
for the OFF function.
OFF:
To deactivate press
and
buttons
simultaneously.
disappears.
SETTING THE TIME
AM
PM
ON
OFF
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
1 2
1.	Press
and
buttons simultaneously. Day flashes.
2.	Press or button to select a number to correspond with the day of the
week (e. g. = Monday, = Tuesday,
= Wed­nesday, = Thursday, = Friday, = Sat­urday, = Sunday).
3.	Press
and
buttons simultaneously. Hour flashes.
4. To select hour press
or
button.
5.	Press
and
buttons simultaneously. Minutes flash.
6.	To select minutes press
or
button.
7.	To confirm press
and
buttons
simultaneously or wait.
17 / 29
INSTALLATION AND OPERATING INSTRUCTIONS
DRAFT 21/11/2018
MANUAL MODE (HANDSET)
NOTICE
BEFORE OPERATING
1. Make sure MANUAL knob on the GV60 valve is in the ON,
full counterclockwise
position.
2. Place the ON / OFF switch (if equipped) in the I (ON) position.
FOR OEM USE ONLY
DESIGNATED LOW FIRE AND HIGH FIRE
NOTE: B
 acklight must be on for high fire and low fire double-click
operation.
AM
▪ To go to low fire, double-click
ton.
is displayed.
but-
NOTE: Flame goes to high fire first before going to low fire.
TO TURN ON FIRE
When pilot ignition is confirmed, motor turns automatically to
maximum flame height.
▪P
 ress
button (One Button Ignition)
or
and
button simultaneously
(Two Button Ignition) until two short
beeps and a blinking series of lines
confirms the start sequence has begun; release button(s).
▪ Main gas flows once pilot ignition is
confirmed.
▪ Handset automatically goes into Manual Mode after main burner ignition.
ON
OFF
1 2
If the pilot does not stay lit after several tries, turn the main valve
knob to OFF and follow the instructions “TURN OFF GAS TO
APPLIANCE” (see page 9).
STANDBY MODE (PILOT FLAME)
Handset
▪ Press and hold
AM
COUNTDOWN TIMER
AM
PM
TO TURN OFF FIRE
AM
PM
NOTE: A new ignition is possible after
the OFF icon stops flashing.
ON
OFF
1 2
FLAME HEIGHT ADJUSTMENT
AM
PM
ON
OFF
1 2
18 / 29
Handset
▪ To increase flame height press and
hold
button.
▪ To decrease flame height or to set appliance to pilot flame, press and hold
button.
but-
If the appliance will not operate, follow the instructions “TURN
OFF GAS TO APPLIANCE” (see page 9).
button to set appliance to pilot flame.
Handset
▪P
 ress
button to turn off.
▪ To go to high fire, double-click
ton.
is displayed.
ON
OFF
1 2
ON / SETTING:
1.	Press and hold
button until displayed, and hour flashes.
2.	To select hour press
or
button.
3.	To confirm press
button. Minutes
flash.
4.	To select minutes press or button.
5.	To confirm press
button or wait.
OFF:
Press
button,
disappear.
and Countdown Time
NOTE: A
 t end of Countdown Time period, the fire shuts off. The
Countdown Timer only works in Manual, Thermostatic,
and Eco Modes. Maximum Countdown Time is 9 hours
and 50 minutes.
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
AM
PM
DRAFT 21/11/2018
MODES OF OPERATION
AM
PM
ON
OFF
1 2
AM
PM
ON
OFF
Thermostatic Mode
 he room temperature is measured and
compared to the set temperature. The
flame height is then automatically adjusted to achieve the set temperature.
FOR OEM USE ONLY
PROGRAM MODE
AM
PM
AM
AM
PM
ON
OFF
ON
OFF
OFF:
1.	Press
or
or
button to enter
Manual Mode.
2.	Press button to enter Thermostatic
Mode.
3.	Press
button to enter Eco Mode.
Default settings:
ON TIME (Thermostatic) TEMPERATURE: 70 °F / 21 °C
OFF TIME TEMPERATURE: “ ” (pilot flame only)
ON
OFF
AM
PM
or
NOTE: The set temperature for Thermostatic Mode is the temperature for the ON time in Program Mode. Changing
the Thermostatic Mode set temperature also changes
the ON time temperature in Program Mode.
AM
PM
THERMOSTATIC MODE
or ,
ON
OFF
1 2
Eco Mode
Flame height modulates between high
and low. If the room temperature is lower than the set temperature, the flame
height stays on high for a longer period
of time. If the room temperature is higher than the set temperature, the flame
height stays on low for a longer period
of time. One cycle lasts approx. 20 min.
1 2
Program Mode
 ROGRAM 1 and 2, each can be proP
grammed to go ON and OFF at specific
times at a set temperature.
1 2
ON:
Press
button.
displayed.
1 2
ON:
Press
button. displayed, preset temperature displayed briefly, and then room
temperature displayed.
TEMPERATURE SETTING:
1.	Press
button and hold until
flashes.
and set temperature (setting in Thermostatic Mode) displayed.
2.	To continue press
button or wait.
displayed, temperature flashes.
3.	Select OFF temperature by pressing
the
or
button.
4.		To confirm press
button.
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
1 2
OFF:
1. Press
button.
2. Press
or button to enter Manual
Mode.
3. Press button to enter Program Mode.
4. Press
button to enter Eco Mode.
NOTE: The ON (Thermostatic) and OFF set temperatures are
the same for each day.
AM
PM
AM
PM
ON
OFF
1 2
SETTING:
1.	Press
button and hold until displayed, temperature flashes.
2.	To adjust set temperature press
or
button.
3. To confirm press
button or wait.
ON
OFF
1 2
DAY SETTING:
5. 
flashes. Press
or
button to
choose between
, , , , ,
, , .
6.	To confirm press
button.
19 / 29
ENGLISH
INSTALLATION AND OPERATING INSTRUCTIONS
INSTALLATION AND OPERATING INSTRUCTIONS
DRAFT 21/11/2018
AUXILIARY FEATURE (2ND BURNER FEATURE)
ON
OFF
1 2
ON TIME SETTING (PROGRAM 1):
7.	 , ,
displayed,
is displayed
shortly, and hour flashes.
	 8. To select hour press
or
button.
9.	To confirm press
button.
, ,
displayed,
displayed shortly,
and minutes flash.
10.	To select minutes press or button.
11. To confirm press
button.
The latching solenoid valve will open automatically after ignition
or after switching the system off, so that the maximum flow of
gas is supplied to both burners assisting with the ignition process. After pressing the AUX-button the motor will turn 7 seconds in the ON direction until the max. position is reached.
AM
PM
ON
OFF
AM
PM
ON
OFF
1 2
NOTE: Either continue to PROGRAM 2 and set on and off times
or stop programming at this point, and PROGRAM 2 remains deactivated.
NOTE: The latching solenoid valve cannot operate manually. If
the receiver battery runs down it will remain in the last
operating position.
ECO MODE
AM
or Daily Timer ( , , , , , , ) selected
▪ Set on time and off time using same procedure as “
selected” (above).
▪
: Set on time and off time for both Saturday and Sunday.
▪ Daily Timer: Unique on and off times may be set for a single
day of the week, for multiple days of the week, or for every day
of the week.
▪ Wait to finish setting.
ON:
Press
button to enter Eco Mode.
displayed.
OFF:
Press
NOTE: PROGRAM 1 and 2 use the same on (Thermostatic) and
off temperatures for
and Daily Timer ( , , , , ,
, ). Once a new on (Thermostatic) and / or off temperature has been set, that temperature becomes the new
default setting.
NOTE: If
or Daily Timer are programmed for PROGRAM 1 and PROGRAM 2 on and off times, these become the new default times. The batteries must be removed to clear the PROGRAM 1 and PROGRAM 2 on
and off times and temperatures.
but-
OFF:
To switch the burner off, press the
button. disappears.
1 2
OFF TIME SETTING (PROGRAM 1):
12.	 , ,
displayed,
is displayed
shortly, and hour flashes.
13.	To select hour, press or button.
14.	To confirm press
button.
, ,
displayed,
displayed shortly, and minutes flash.
15.	To select minutes press or button.
16. To confirm press
button.
ON:
To switch a burner on, press the
ton. displayed.
button.
disappears.
CIRCULATING FAN OPERATION
AM
Circulating fan has 4 speed levels from
low (1 bar) to high (4 bars).
SETTING:
1.	Press
button and hold until
flashes.
2.	Press button to increase fan speed
and
button to decrease fan speed.
3.	To confirm setting either press button or wait ( displayed).
OFF:
	Press
button until all 4 speed level
bars disappear.
NOTE: S
 ETTING only. If the fan was not switched off after last
use, it starts automatically 4 minutes after ignition at maximum speed and goes to the last set level after 10 seconds. The fan stops 10 minutes after the gas is OFF or
at pilot.
20 / 29
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
SELECTED
AM
PM
FOR OEM USE ONLY
INSTALLATION AND OPERATING INSTRUCTIONS
DRAFT 21/11/2018
FOR OEM USE ONLY
LIGHT / DIMMER OPERATION
AM
ON:
Press
button (
on at preset level.
OFF:
Press
displayed). Light is
button ( disappears).
ENGLISH
SETTING:
1.	Press button and hold until flashes.
2.	
To adjust light between 20…100 %
press
or
button.
3.	To confirm setting either press button or wait ( displayed).
NOTE: The Light works independently of the pilot flame. If you
want the light on but no flame, press
button.
MYFIRE APP
NOTICE
Before the app can be used, the myfire Wi-Fi Box must be wired
and plugged into mains power according to myfire app setup
diagram (see figure 30, page 29), and the app setup must be
completed (see myfire app setup, page 24).
AM
PM
ON
OFF
1 2
If Thermostatic, Program or Eco Mode
is activated, the corresponding icon and
“ ” is displayed on the handset.
The modes can be operated according
to the descriptions on previous pages.
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
NOTE: In Manual Mode “ ” is NOT
displayed on the handset.
21 / 29
DRAFT 21/11/2018
INSTALLATION AND OPERATING INSTRUCTIONS
FOR OEM USE ONLY
THE PUCK HANDSET
The Puck is a smart control that works in conjunction with the
GV60 / Symax system. Its basic functions include turning the fire
on and off and turning the flame height up and down.
The Puck is equipped with temperature sensing that allows the
use of the popular myfire app.
ON / OFF
Down /LO
SYNCHRONIZATION RECEIVER / THE PUCK HANDSET
NOTICE
See page 7 for more information about synchronization between
receiver and The Puck handset.
MODES OF OPERATION
Up / HI
Figure 23: 3-button layout
TECHNICAL DATA
AMBIENT TEMPERATURE RANGE
CSA: The Puck: 32 °F to 131 °F
CE: The Puck: 0 °C to 55 °C
RADIO FREQUENCY
	CSA:	918 MHz for U.S. and for Canada (The Puck, receiver)
CE: 868 MHz for Europe (The Puck, receiver)
(see radio frequency information on page 4.)
POWER SUPPLY
Handset: 2 x 1.5 V “AAA” (quality alkaline recommended)
			
When pilot ignition is confirmed, motor turns automatically to
maximum flame height.
TURN FIRE ON AND OFF
▪ Press and hold the button until two
short beeps confirms the start sequence has begun; release button.
▪ Main gas flows once pilot ignition is
confirmed.
▪ Press and hold the
button to turn
OFF.
If the pilot does not stay lit after several tries, turn the main valve
knob to OFF and follow the instructions “TURN OFF GAS TO
APPLIANCE” (see page 9).
STANDBY MODE (PILOT FLAME)
▪ Press and hold the "–" button to set
appliance to pilot flame
NOTICE
Wiring of valve and receiver must be completed before starting
ignition. Failure to do so could damage the electronics.
NOTICE
To avoid damaging the electronics, do NOT use metal tools to
remove the batteries from the handset / receiver.
▪	Without using a mains adapter, battery replacement is recommended at the beginning of each heating season.
▪	Old or dead batteries should be removed immediately. If left
in the unit the batteries can overheat, leak, and / or explode.
▪	Do NOT expose batteries (including during storage) to direct
sunlight, excessive heat, fire, moisture, or severe impact. Each
of these conditions can cause the batteries to overheat, leak,
and / or explode.
▪	Batteries must be kept within their recommended temperature
limits (ambient battery temperature range: 32 °F to 131 °F /
0 °C to 55 °C).
▪	New and old batteries and different brands of batteries should
not be used together. Mixing of various batteries can cause
the batteries to overheat, leak, and / or explode.
22 / 29
FLAME HEIGHT ADJUSTMENT
▪ To increase flame height press and
hold "+" button.
▪ To decrease flame height or to set appliance to pilot flame, press and hold
"–" button.
DESIGNATED LOW FIRE AND HIGH FIRE
▪ To go to hi fire, double-click "+" button.
▪ To go to low fire, double-click "–" button.
NOTE: F
 lame goes to high fire first before going to low fire.
If the appliance will not operate, follow the instructions “TURN
OFF GAS TO APPLIANCE” (see page 9).
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
The handsets and receivers are not interchangeable with
previous electronics.
INSTALLATION AND OPERATING INSTRUCTIONS
DRAFT 21/11/2018
FOR OEM USE ONLY
MYFIRE WI-FI BOX (B6R-W2…)
The new Wi-Fi Box has a faster processing speed, variable power
supply between 5 and 24 volts, two RGB outlets, identical connectors on both ends of the cable, and the Wi-Fi Box itself has a
much smaller footprint.
Receiver WLAN
LED 1
LED 2
RGB 1
RGB 2
RGB
Power Input
Receiver cable
AMBIENT TEMPERATURE RANGE
CSA: myfire Wi-Fi Box: 32 °F to 176 °F
CE: myfire Wi-Fi Box: 0 °C to 80 °C
RADIO FREQUENCY
CSA + CE: 2.4 GHz
(see radio frequency information on page 4.)
POWER SUPPLY
	6 V connection to the receiver which is connected to an AC
mains adapter.
WIRELESS COMMUNICATION
▪ 	WPA2 authentication
▪ 	AES 256-bit encryption security
▪ 	Compatible with IEEE 802.11 b/g/n
POWER CONSUMPTION
CSA + CE: Nominal:
max. 0.5 W
CSA + CE: Standby:
max. 5 mA
LED RGB CONTROL OUTPUT
CSA + CE: 	 Phoenix, 3 pol, MC 1.5 / 3-ST-3.5,
5 VDC - 24 VDC / 5 A
LED RGB EXTERNAL POWER INPUT
CSA + CE: 	 Phoenix, 2 pol, MC 1.5 / 2-ST-3,
5 VDC - 24 VDC / 5 A
MODES OF OPERATION
The myfire Wi-Fi Box communicates with a home network (Wi-Fi
Router) over a wireless signal.
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
1.	The myfire Wi-Fi Box must be wired to the receiver according
to the myfire app setup diagram (see figure 30, page 29)
2.	Connect receiver to mains power. The myfire Wi-Fi Box start
with the Access Point Mode (green/blue LED blinking). Go to
“myfire app setup”…
MINIMUM REQUIREMENT FOR WI-FI ROUTER
▪	IEEE 802.11n/g/b compatibility
▪	WPA2 encryption
▪ Radio frequency: 2.4 GHz band
▪	Wireless auto channel: Automated search for WLAN radio
channel free of interference
▪	User Datagram Protocol (UDP) support
▪	multicast DNS (mDNS) for Kwik Connect process
MINIMUM REQUIREMENT SMART DEVICE:
▪ iOS 8.0 or Android 4.2
Reset button
(Use paper clip to push button)
Figure 24: myfire Wi-Fi Box (B6R-W2…)
LED INDICATION ON MYFIRE WI-FI BOX (see figure 24, page 23)
2 RGB LEDs
Label
Receiver
LED 1
WLAN
LED 2
LED
Status
Green
Connected to receiver.
Red
Not connected to receiver.
Off
Standby mode is active or no Power supply.
Green
Wi-Fi connection is safe.
Blue/Green blinking
Access point mode (AP mode) is active.
Red
Not connected to home network (Wi-Fi Router).
Off
Standby mode is active or no power supply.
RESET STATUS ON MYFIRE WI-FI BOX:
Press Reset
Button
LED
Function
Power-OnReset or
1-sec-Reset
WLAN LED 2
flashes red,
green and
blue
If no network is set, the AP Mode will be activated
for 2 hours. When the network isn't set after 2
hours, the Wi-Fi Box will go to Standby Mode.
Once a network is set, the Wi-Fi Box will connect
directly.
7 secs
WLAN LED 1
flashes every
500 ms in blue
Removes the Wi-Fi settings and turns on the
Access point mode (AP mode) for 2 hours.
20 secs
WLAN LED 1
flashes every
50 ms in blue
Erases all Setup Data. The Wi-Fi chip will be set
to the last version after the reboot. The AP-Mode
will be activated for 2 hours.
NOTICE
▪	A Symax handset or The Puck must be used to achieve full
functionality.
▪	If mains power is lost, disconnect the myfire Wi-Fi Box from
the receiver. This will prevent receiver batteries from being
drained quickly.
▪	Multiple users on the same Wi-Fi channel may interfere with the
data transfer. Press reset button on the myfire Wi-Fi Box for 1
second to change current channel (see figure 24, page 23).
▪	If no network is configured, the myfire Wi-Fi Box will leave the
Access Point Mode (AP Mode) after 2 hours.
▪	If you have multiple fireplaces using myfire Wi-Fi Boxes, the
minimum distance between the myfire Wi-Fi Boxes must be 60
cm (2'). A shorter distance may interfere with the data transfer.
Do not connect the combination control system to the LED
connections of the myfire Wi-Fi Box.
23 / 29
ENGLISH
TECHNICAL DATA
INSTALLATION AND OPERATING INSTRUCTIONS
DRAFT 21/11/2018
FOR OEM USE ONLY
MYFIRE APP SETUP
NOTICE
For more detailed app setup / operating instructions refer to
www.myfireapp.com
INITIAL SETUP
1.	Download myfire app from Apple App Store or Google Play
Store.
2.	Touch screen to start app setup.
3.	
Choose language, temperature (°C or °F) and time format
(12 or 24 hour).
REGISTRATION
NOTE: Y
 ou must register before logging in. Registration is one
time only.
1. Fill in data and accept the “Privacy Policy”.
2. Touch “OK” in pop-up notice.
3. Touch link to confirm email verification.
4.	You will be shown a message that you have successfully registered the myfire app.
5. Return to app.
LOGIN
1. Fill in your registration password.
2. Accept “Terms and Conditions”.
3. Touch the “Login” button.
KWIK CONNECT
CONNECT SMART DEVICE TO MYFIRE WI-FI BOX
1. Touch the
icon.
2.	The Home Wi-Fi Network name your smart device is currently
connected to is displayed.
3. Type in the password of the displayed Home Wi-Fi Network.
4.	Touch "Connect". The myfire App starts connecting the myfire
Wi-Fi Box to the selected Home Wi-Fi Network.
COMPLETE MYFIRE APP SETUP
1. Type in a name for your fireplace or select an icon.
2. Activate Fan, Light and AUX if installed to your fireplace.
3. Touch "Finish" to complete the setup.
The home screen is displayed and the myfire app is ready to go.
STANDARD SETUP
IF KWIK CONNECT IS NOT AVAILABLE, AND YOU HAVE ENTERED THE CORRECT PASSWORD, USE STANDARD SETUP.
1. Type in the password of the displayed Home Wi-Fi Network.
2.	Follow the instructions on the screen and touch the "Standard
Setup" button to proceed.
3.	Go to your smart device Wi-Fi settings and select the myfire
Wi-Fi Box network (myfire_WiFi-Box_) you want to
connect.
4. Go back to the myfire app setup and follow the instructions on
the screen. Your selected Wi-Fi Box network name from the
smart device Wi-Fi settings.
24 / 29
USE RETRY IF PASSWORD IS INCORRECT
1. Touch the "Retry" button to repeat the Kwik Connect process.
2. Type in the correct password.
NOTICE
To connect myfire Wi-Fi Box to Wi-Fi Router (home network),
make sure:
▪ Home network is available.
▪ Home network name and password are correct.
▪ SSID of the Wi-Fi Router is not hidden.
▪ Home network signal is in range.
▪ Wi-Fi Router supports User Datagram Protocol (UDP).
NOTICE
▪	After setting up the myfire Wi-Fi Box and myfire app, the time
has to be synchronized in the settings of the myfire app.
▪	The active device (The Puck or Symax handset or smart
device) is the one last used. An exception is if the non-active
devise is used to change Light, Fan, or AUX. The non-active
device will make the changes, but the active device remains
so if it is in Thermostatic, Program, or Eco Mode. If a Profile
includes a Thermostatic, Program, or Eco setting it will also
cause the active device to remain active.
▪	If Thermostatic, Program, or Eco Mode is activated using the
app, the corresponding icon and “ ” is displayed on the
Symax handset (see figure 25, page 24).
▪	During motor movement no information between receiver and
transmitter is exchanged. The synchronization follows after
motor has stopped.
▪	The room temperature data is transferred by the handset
during synchronization.
Figure 25: App connected (in Thermostatic Mode)
NOTICE
It is the responsibility of the OEM to consider the following:
▪ The location of the GV60 system components will significantly
effect the radio signal strength.
▪ The type of materials (e.g. sheet metal) used in the construction of
the gas fireplace will significantly effect the radio signal strength.
▪ Operate the system with a dedicated mains power supply
and/or batteries.
▪ Do not use near household electrical wiring and/or magnetic
fields.
▪ Other transmitters using the same signal will negatively affect
the radio signal strength.
▪ Adjustment of the on-board antenna on the receiver can
improve signal strength.
▪ Do not store or locate the GV60 system components in a hot,
cold, or humid environment.
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
For myfire app setup, you will need your Wi-Fi network SSID
and password.
Interrupter Block
G60-ZUS…
Ignition Cable
G60-ZKIS…
Pilot Burner
G30-ZP2M-L
Antenna
Receiver
B6R-R8(9)P…
Combination Control
GV60…
RESET Button
ENGLISH
Mains Adapter (optional)
G60-ZMA3
Wall Switch (optional)
G6R-ZWSE(N)…
DOWN
ON-OFF
UP
Thermocurrent Cable TC
G60-ZKIRS…
Thermocurrent Cable SW
with ON / OFF Switch
G60-ZSKS(L)S…
8 Wire Cable
G6R-C…
DRAFT 21/11/2018
The receiver B6R-R8(9)PT… has main burner supervision (2nd thermocouple option). This option is
programmed so that it cannot be used without the second thermocouple installed and vice versa.
Additional functions
The universal receivers B6R-R8(9)P… and B6R-R8(9)PT… can be used to start a power flue control (2pin outlet) or to operate a second burner or a relay (3pin outlet). Together with a module, the
receiver controls a circulating fan and a dimmer.
Main Burner
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
INSTALLATION AND OPERATING INSTRUCTIONS
FOR OEM USE ONLY
WIRING DIAGRAMS
BASIC
Figure 26
25 / 29

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : © Mertik Maxitrol GmbH & Co. KG
Create Date                     : 2018:11:21 13:19:34+01:00
Modify Date                     : 2019:01:28 16:28:42+01:00
Sensitivity                     : Confidential Confidential - Label
MSIP Label 289bd 36d-23ac-4bc 9-9c 00-d 421e 181dc 1a Name: Confidential
MSIP Label D938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Name: Confidential - Label
MSIP Label 289bd 36d-23ac-4bc 9-9c 00-d 421e 181dc 1a Owner: christa.jaeger@csagroup.org
MSIP Label D938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Owner: christa.jaeger@csagroup.org
MSIP Label 289bd 36d-23ac-4bc 9-9c 00-d 421e 181dc 1a Site Id: e600ad84-320a-43ef-bfa4-8f5d25019bde
MSIP Label D938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Parent: 289bd36d-23ac-4bc9-9c00-d421e181dc1a
MSIP Label D938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Site Id: e600ad84-320a-43ef-bfa4-8f5d25019bde
MSIP Label 289bd 36d-23ac-4bc 9-9c 00-d 421e 181dc 1a Enabled: True
MSIP Label 289bd 36d-23ac-4bc 9-9c 00-d 421e 181dc 1a Set Date: 2019-01-28T15:12:27.0397561Z
MSIP Label D938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Enabled: True
MSIP Label D938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Set Date: 2019-01-28T15:12:27.0397561Z
MSIP Label 289bd 36d-23ac-4bc 9-9c 00-d 421e 181dc 1a Application: Microsoft Azure Information Protection
MSIP Label D938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Application: Microsoft Azure Information Protection
MSIP Label 289bd 36d-23ac-4bc 9-9c 00-d 421e 181dc 1a Extended MSFT Method: Manual
MSIP Label D938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Extended MSFT Method: Manual
Language                        : de-DE
XMP Toolkit                     : XMP Core 5.5.0
Instance ID                     : uuid:6b4059d7-f81d-3646-9c5d-5f4ba1a54eef
Original Document ID            : adobe:docid:indd:89ae7fdd-b400-11df-931f-97454b1087d1
Document ID                     : xmp.id:2e1c2466-7bb7-41de-9809-a0b66b7b688a
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:c416b386-c40d-4407-bdaa-a77df67118ca
Derived From Document ID        : xmp.did:dd5757ec-bd59-4f6f-97ce-eff813af2f2d
Derived From Original Document ID: adobe:docid:indd:89ae7fdd-b400-11df-931f-97454b1087d1
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 13.1 (Macintosh)
History Changed                 : /
History When                    : 2018:11:21 13:19:34+01:00
Metadata Date                   : 2018:11:21 13:20:09+01:00
Creator Tool                    : Adobe InDesign CC 13.1 (Macintosh)
Format                          : application/pdf
Creator                         : © Mertik Maxitrol GmbH & Co. KG
Subject                         : Mertik Maxitrol
Rights                          : © Mertik Maxitrol GmbH & Co. KG
Caption Writer                  : © Mertik Maxitrol GmbH & Co. KG
City                            : Thale
State                           : Sachsen-Anhalt
Country                         : Deutschland
Credit                          : © Mertik Maxitrol GmbH & Co. KG
Source                          : © Mertik Maxitrol GmbH & Co. KG
Marked                          : True
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Creator Address                 : Warnstedter Str.3
Creator City                    : Thale
Creator Region                  : Sachsen-Anhalt
Creator Postal Code             : 06502
Creator Country                 : Deutschland
Creator Work Telephone          : +4939474000
Creator Work Email              : info@mertikmaxitrol.com
Creator Work URL                : www.mertikmaxitrol.com
Image Creator Name              : © Mertik Maxitrol GmbH & Co. KG
Copyright Owner Name            : © Mertik Maxitrol GmbH & Co. KG
Copyright Owner ID              : © Mertik Maxitrol GmbH & Co. KG
MSIP Label d 938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Enabled: True
MSIP Label d 938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Site Id: e600ad84-320a-43ef-bfa4-8f5d25019bde
MSIP Label d 938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Owner: christa.jaeger@csagroup.org
MSIP Label d 938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Set Date: 2019:01:28 15:12:27.0397561Z
MSIP Label d 938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Name: Confidential - Label
MSIP Label d 938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Application: Microsoft Azure Information Protection
MSIP Label d 938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Parent: 289bd36d-23ac-4bc9-9c00-d421e181dc1a
MSIP Label d 938dec 7-e 99c-4a 7e-b 377-36be 797db 649 Extended MSFT Method: Manual
Page Count                      : 11

EXIF Metadata provided by EXIF.tools