NEXCOM VTC6110X00 Intelligent Vehicle Telematics Computer User Manual 3

Download:
Mirror Download [FCC.gov]
Document ID	1350972
Application ID	Y3Fv7/Mb2bLi2pPXkncWCA==
Document Description	User manual3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	161.76kB (2022005 bits)
Date Submitted	2010-09-29 00:00:00
Date Available	2010-11-15 00:00:00
Creation Date	2010-07-26 05:49:21
Producing Software	Adobe PDF Library 8.0
Document Lastmod	2010-07-26 05:49:35
Document Title	User manual3
Document Creator	Adobe InDesign CS3 (5.0)

Chapter 2: Jumpers and Connectors
LAN Connector
USB Connector
Connector size: RJ-45
Connector location: LAN1
Connector location: USB1
Connector Pin Definition
Connector Pin Definition
Pin
Definition
Pin
Pin
Definition
TX+
TX-
RX+
N/C1
N/C2
RX-
N/C3
N/C4
LAN Speed LED
10
+3.3V
11
LAN Link LED
12
+3.3V
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
27
Definition
Pin
Definition
VCC
DATA-
DATA+
GND
VTC 6110 User Manual
Chapter 2: Jumpers and Connectors
USB Connector
LVDS Power Connector
Connector location: USB2
Connector location: J5
Connector Pin Definition
Connector Pin Definition
Pin
Pin
Definition
Definition
VCC
DATA1-
DATA1+
GND
VCC
DATA-
DATA+
GND
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
28
Pin
Definition
Pin
Definition
Panel_backlight
Panel_VDD
GND
GND
LVDS_PANEL
LVDS_BIASON
VTC 6110 User Manual
Chapter 2: Jumpers and Connectors
External 12V & 5V Power and SMBUS Connector
Mic-in
Connector location: CN2
Connector location: CN11 and CN15
Connector Pin Definition
Connector Pin Definition
Pin
Definition
Pin
5V
12V
SMBCLK
GND
GND
SMBDATA
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Pin
Definition
29
Definition
Pin
Definition
NC
MIC_JD
NC
MIC_OUT
GND
GND
VTC 6110 User Manual
Chapter 2: Jumpers and Connectors
Line-out
PCI-104 VI/O Voltage Setting
Connector location: CN8 and CN14
Connector location: J13
Connector Pin Definition
Pin
Definition
Pin
LINE_OUT_L
SURR_JD
NC
LINE_OUT_R
GND
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Definition
Connector Pin Definition
GND
30
Pin No.
Status
1-3, 2-4 (default)
Short
Function Description
+3.3V
3-5, 4-6
Short
+5V
VTC 6110 User Manual
Chapter 2: Jumpers and Connectors
PCI-104 Connector
Power Button
Connector location: CN16
Connector location: SW1
Connector Pin Definition
Reset Button
Connector location: SW2
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
31
VTC 6110 User Manual
Chapter 2: Jumpers and Connectors
MCU COM Port
ACC_ON LED
Connector location: JP3
Connector location: JP7
Connector Pin Definition
Pin
Function Description
TX
RX
Pin
Function Description
GND
+3.3V LED
GND
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Connector Pin Definition
32
VTC 6110 User Manual
Chapter 2: Jumpers and Connectors
Temp Sensor
DC Power Input Connector
Connector location: JP8
Connector location: CN1
Connector Pin Definition
Pin
Function Description
SENSOR+
GND
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Connector Pin Definition
Pin
33
Function Description
GND
VIN (6V~36V)
IGNITION
VTC 6110 User Manual
Chapter 2: Jumpers and Connectors
Power On and IDE Active LED
GPIO and UMTS LEDs
Connector location: LED1
Connector location: LED2
T1
T2
B1
B2
LED I/O Port Address and Data
Connector Pin Definition
LED
Function Description
LED
Function Description
T1
POWER LED
T2
I/O PORT Address: 0EE0; Bit0: 1 (Light), 0 (Dark)
B1
HD LED
B2
UMTS STATUS
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
34
VTC 6110 User Manual
Chapter 2: Jumpers and Connectors
Serial ATA
Serial ATA Power Input
Connector location: CN6
Connector location: J10
Connector Pin Definition
Connector Pin Definition
Pin
Definition
Pin
Definition
Pin
Definition
GND
SATA_TXP0 -
+V12S
GND
SATA_TXN0
GND
GND
+V5S
SATA_RXN0
SATA_RXP0
GND
Pin
Definition
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
35
VTC 6110 User Manual
Chapter 2: Jumpers and Connectors
Mini-PCIe Socket (for 3.5G module)
PCIe Interface
Mini-PCIe Socket (for WLAN module)
USB + PCIe Interface
Connector location: CN10
Connector location: CN13
52
52
51
51
Connector Pin Definition
Pin
Definition
Pin
Connector Pin Definition
Definition
Pin
Definition
Pin
Definition
Definition
Pin
Definition
Pin
Definition
MIC +
+V3.3S
27
GND
28
NC
WAKE#
+V3.3S
27
GND
28
+V1.5S
MIC -
GND
29
GND
30
NC
NC
GND
29
GND
30
SMB_CLK
SPK +
NC
31
NC
32
NC
NC
+V1.5S
31
PETn0
32
SMB_DATA
GND
USIM PWR
33
RESET
34
GND
CLKREQ#
NC
33
PETp0
34
GND
GND
10
USIM DATa
35
GND
36
USB_D-
GND
10
NC
35
GND
36
USB_D-
11
VCC_
MSM26_
DIG
12
USIM CLK
37
GND
38
USB_D+
11
REFCLK-
12
NC
37
NC
38
USB_D+
13
REFCLK+
14
NC
39
NC
40
GND
13
NC
14
USIM RST
39
+V3.3S
40
GND
15
GND
16
NC
41
NC
42
15
GND
16
NC
41
+V3.3S
42
LED_
WWAN#
LED_
WWAN#
17
NC
18
GND
43
NC
44
17
NC
18
GND
43
GND
44
NC
LED_
WLAN#
19
NC
20
W_DISABLE#
45
NC
46
NC
19
NC
20
DISABLE#
45
NC
46
LED_
WPAN#
21
GND
22
NC
47
NC
48
NC
21
GND
22
PERST#
47
NC
48
+V1.5S
23
NC
24
NC
49
NC
50
GND
23
PERn0
24
+3.3S
49
NC
50
GND
25
NC
26
GND
51
NC
52
+V3.3S
25
PERp0
26
GND
51
NC
52
+V3.3S
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Pin
36
Definition
Pin
VTC 6110 User Manual
Chapter 2: Jumpers and Connectors
Bluetooth Connector
Connector location: CN4
Connector location: J7
MH2
MH1
SIM Card Connector
10
J7
JST-1mm-M-90
Pin
Connector Pin Definition
Pin
Definition
Pin
Definition
Pin
Definition
GND
USB_6P_L
Definition
USB_6N_L
NC
NC
BT_AUDIO_EN_R
C1
POWER VOLTAGE
C2
RESET SIGNAL
C3
CLOCK SIGNAL
C5
GND
NC
BT_3.3V
I/O
NC
10
GND
C6
VPP:PROGRAM VOLTAGE
SW
Contact present switch
C7
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
37
VTC 6110 User Manual
Chapter 3: System Setup
Chapter 3: System Setup
Removing the Chassis Cover
Prior to removing the chassis cover, make sure the unit’s power is
off and disconnected from the power sources to prevent electric
shock or system damage.
1. The screws on the cover are used to secure the cover to the chassis.
Remove these screws and put them in a safe place for later use.
Bottom View
2. Lift the cover upward then remove it from the chassis.
Front View
Rear View
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
38
VTC 6110 User Manual
Chapter 3: System Setup
Installing a GPRS/UMTS/HSDPA Module
2. Insert the module into the Mini PCI Express slot at a 45 degrees angle
until the gold-plated connector on the edge of the module completely
disappears inside the slot.
1. The Mini PCI Express slot shown below is used to install a 3.5G communication module such as GPRS, UMTS or HSDPA module.
GPRS/UMTS/
HSDPA module
Mini PCI
Express slot
Mini PCI
Express slot
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
39
VTC 6110 User Manual
Chapter 3: System Setup
3. Push the module down then secure it with mounting screws.
4. Attach one end of the RF cable onto the module.
Attach RF cable
to the module
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
40
VTC 6110 User Manual
Chapter 3: System Setup
5. The photo below shows one end of the RF cable properly attached
onto the module.
6. Mount the other end of the cable to the antenna mounting hole located at the front panel of the chassis.
RF cable mounted
at the front panel
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
41
VTC 6110 User Manual
Chapter 3: System Setup
Installing a Wireless LAN Module
2. Insert the wireless LAN module into the Mini PCI Express slot at a 45
degrees angle until the gold-plated connector on the edge of the module completely disappears inside the slot.
1. The Mini PCI Express slot shown below is used to install a wireless LAN
module.
Wireless LAN
module
Mini PCI
Express slot
Mini PCI
Express slot
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
42
VTC 6110 User Manual
Chapter 3: System Setup
3. Push the module down then secure it with mounting screws.
4. Attach one end of the RF cable onto the module.
Attach RF
cable to the
module
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
43
VTC 6110 User Manual
Chapter 3: System Setup
5. The photo below shows one end of the RF cable properly attached
onto the module.
6. Mount the other end of the cable to the antenna mounting hole located at the front panel of the chassis.
RF cable mounted
at the front panel
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
44
VTC 6110 User Manual
Chapter 3: System Setup
Installing a Bluetooth Module
2. Install the provided mounting stud as shown in the illustration below.
1. The USB header shown below is used to install a Bluetooth module.
Mounting
stud
USB
header
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
45
VTC 6110 User Manual
Chapter 3: System Setup
3. Insert the Bluetooth module’s cable connector into the USB header.
4. Attach one end of the RF cable onto the module.
Push the module down then secure it with a mounting screw.
Attach RF
cable to the
module
Mounting
screw
5. Mount the other end of the cable to the Bluetooth mounting hole
located at the front panel of the chassis.
Bluetooth module
Cable connector
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
46
VTC 6110 User Manual
Chapter 3: System Setup
Installing a CompactFlash Card
2. With the CompactFlash card’s label facing up, position the card to the
socket.
1. Locate for the CompactFlash socket on the board.
CompactFlash
card
CompactFlash
socket
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
47
VTC 6110 User Manual
Chapter 3: System Setup
3. Insert the card until it is completely seated in the socket.
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
48
VTC 6110 User Manual
Chapter 3: System Setup
Installing the PCI-104 Module
2. Position the PCI-104 module above the slot then press it down firmly
until it is completely seated in the slot. This will at the same time align
the module’s mounting holes to the mounting studs on the board.
1. Locate for the PCI-104 slot on the board.
PCI-104
module
Mounting
hole
PCI-104 slot
Mounting
stud
Mounting stud
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
49
VTC 6110 User Manual
Chapter 3: System Setup
3. Secure the module with mounting screws.
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
50
VTC 6110 User Manual
Chapter 3: System Setup
Installing a SATA Hard Drive
• During Windows XP OS installation, press “F6” to select and
install the SATA driver.
1. The metal bracket is used to hold a SATA hard drive. First, remove the
screws that secure the metal bracket to the board then remove the
bracket.
• If you intend to install a Windows XP SP2 or earlier version, you
must first set the “USB 2.0 Controller” field (in the BIOS) to
Disabled.
• By default, the “Legacy USB Support” field (in the BIOS) is
Disabled. If you are using a USB device to install the Windows
operating system, you must first set this field to Enabled. Set this
field back to Disabled after you have finished the installation.
2. Position the HDD brackets on each side of the SATA drive. Align the
mounting holes that are on the sides of the SATA drive with the HDD
brackets’ mounting screws.
Metal
bracket
Mounting
screws
HDD bracket
If you intend to install a CompactFlash card or a Mini PCI Express
module, please install these devices first before proceeding to the
next step. Refer to their respective sections in this chapter for instructions on installing a CF card or a Mini PCI Express module.
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
SATA drive
Mounting
screws
51
VTC 6110 User Manual
Chapter 3: System Setup
3. Tighten the mounting screws to secure the HDD brackets in place.
4. Now place the SATA drive on the metal bracket then tighten the head
bolt screws to secure the drive on the metal bracket.
Head bolt screw
HDD bracket
HDD bracket
Metal bracket
Screwdriver
Top View
HDD bracket
HDD bracket
Screwdriver
Bottom View
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
52
VTC 6110 User Manual
Chapter 3: System Setup
5. Align the head bolt screws with the mounting studs on the board.
Tighten the head bolt screws to secure the drive to the chassis.
6. Locate for the SATA connector and the power connector. on the board.
Mounting stud
Power connector
SATA connector
Head bolt screw
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
53
VTC 6110 User Manual
Chapter 3: System Setup
8. Connect one end of the SATA power cable to the SATA power connector that is on the board then connect the other end of the cable to the
SATA power connector at the rear of the SATA drive.
7. Connect one end of the SATA data cable to the SATA connector that is
on the board then connect the other end of the cable to the SATA connector at the rear of the SATA drive.
SATA data cable
Cable connected to
the SATA connector
on the board
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Cable connected to the
SATA power connector
on the board
Cable connected
to the SATA drive
54
SATA power cable
Cable connected
to the SATA drive
VTC 6110 User Manual
Chapter 3: System Setup
Installing the SODIMM
2. Insert the module into the socket at an approximately 30 degrees
angle. Apply firm even pressure to each end of the module until it slips
into the socket. The gold-plated connector on the edge of the module
will almost completely disappear inside the socket.
1. Remove the heatspreader’s mounting screws.
SODIMM
socket
Heatspreader
SODIMM
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
55
VTC 6110 User Manual
Chapter 3: System Setup
3. Push the module down until the clips on both sides of the socket lock
into position. You will hear a distinctive “click”, indicating the module
is correctly locked into position.
Clip
Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
56
VTC 6110 User Manual

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Count                      : 30
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:b788fd7b-7991-49b7-aa9b-e1e984e4a47b
Modify Date                     : 2010:07:26 05:49:35+08:00
Create Date                     : 2010:07:26 05:49:21+08:00
Metadata Date                   : 2010:07:26 05:49:35+08:00
Document ID                     : uuid:46b7e1f5-4faf-4499-b420-9bf8de7b5a95
Format                          : application/pdf
Tagged PDF                      : Yes
Creator                         : Adobe InDesign CS3 (5.0)
Producer                        : Adobe PDF Library 8.0

EXIF Metadata provided by EXIF.tools