Realtek Semiconductor RTL8191SE NOTEBOOK User Manual U10IL1 English

Realtek Semiconductor Corp. NOTEBOOK U10IL1 English

UserManual.wiki >

Realtek Semiconductor >

RTL8191SE User Manual >

Contents

USERS MANUAL

i Preface ©©Copyright 2009 All Rights Reserved. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer. Limitation of Liability While reasonable efforts have been made to ensure the accuracy of this manual, the manufacturer and distributor assume no liability resulting from errors or omissions in this manual, or from the use of the information contained herein. Notices Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

ii ¾ Reorient or relocate the receiving antenna ¾ Increase the separation between the equipment and receiver ¾ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Notice: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Shielded interface cables and a non-shielded AC power cord must be used in order to comply with emission limits. This equipment is to be used with power supply: 30/40W There is no internal power supply. FCC RF Radiation Exposure Statement:1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. Max. SAR Measured(1g):0.901W/Kg

iii Table of Content BEFORE YOU START ...............................................................................2 LET YOUR COMPUTER ACCLIMATE ITSELF ..............................................8 HEAT, COLD, HUMIDITY, AND GLARE ....................................................9 SUITABLE PLACE TO WORK...................................................................9 INTRODUCTION......................................................................................11 FRONT VIEW .....................................................................................12 LEFT VIEWS ......................................................................................14 RIGHT VIEW ......................................................................................16 GETTING STARTED ...............................................................................19 CONNECTING THE AC ADAPTER.........................................................19 TO INSTALL THE BATTERY PACK:........................................................21 TO REMOVE THE BATTERY PACK: ......................................................22 USING THE NOTEBOOK COMPUTER.......................................................24 LCD CARE........................................................................................24 EXTERNAL CRT DISPLAY...................................................................25 FUNCTION KEYS (QUICK KEYS)..........................................................25 OSD-BAR ICON.................................................................................28 POWER SAVING MODE.......................................................................30 NORMAL MODE .................................................................................30 HIGH PERFORMANCE MODE...............................................................31 DVD PLAY MODE..............................................................................31 DYNAMIC SWITCH MODE....................................................................32 TOUCHPAD PRECAUTIONS .................................................................33 THE BATTERY POWER SYSTEM ..........................................................34 PREPARING THE BATTERY PACK FOR USE (BATTERY CALIBRATION) ....34 AUTOMATIC BATTERY PACK CHARGING FUNCTION..............................35 BATTERY STATUS..............................................................................35 BATTERY LOW WARNING ...................................................................35 SMALL BATTERY FOR THE REAL TIME CLOCK......................................36 HELP WINDOWS ................................................................................37 DESKTOP ..........................................................................................37 INTERNET CONNECTION ........................................................................43 RUNNING BIOS SETUP .........................................................................48 MAIN SETUP .....................................................................................49 INFO SETUP ......................................................................................50 ADVANCED SETUP.............................................................................51 SECURITY .........................................................................................51 POWER SETUP..................................................................................52 BOOT SETUP.....................................................................................52

iv EXIT SETUP ......................................................................................53 VGA UTILITIES .....................................................................................58 3G CONNECTION ..................................................................................64 TROUBLESHOOTING ..............................................................................69 NO SPEAKER OUTPUT ........................................................................70 SOUND CANNOT BE RECORDED ..........................................................70 THE HARD DISK DRIVE DOES NOT WORK OR IS NOT RECOGNIZABLE .......71 THE HARD DRIVE IS MAKING ABNORMAL WHINING NOISES .....................71 THE HARD DISK DRIVE HAS REACHED ITS CAPACITY .............................71 THE HARD DISK TAKES LONGER TO READ A FILE...................................72 THE FILES ARE CORRUPTED ...............................................................72 THE DISPLAY PANEL IS BLANK WHEN THE SYSTEM IS TURNED ON ..........72 THE SCREEN IS DIFFICULT TO READ ....................................................72 THE SCREEN FLICKERS ......................................................................72 THE BUILT-IN TOUCH PAD PERFORMS ERRATICALLY .............................72 THE BUILT-IN KEYBOARD ACCEPTS NO INPUT .......................................73 THE CHARACTERS ON THE SCREEN REPEAT WHILE I TYPE ....................73 A MESSAGE “CMOS CHECKSUM FAILURE” DISPLAYS DURING THE BOOTING PROCESS OR THE TIME (CLOCK) RESETS WHEN BOOTING .......73 THE POST DOES NOT SHOW AN INCREASED MEMORY CAPACITY WHEN YOU HAVE ALREADY INSTALLED ADDITIONAL MEMORY ..........................73 THE O/S ISSUES AN INSUFFICIENT MEMORY ERROR MESSAGE DURING OPERATION .......................................................................................74 PC CARDS DO NOT FUNCTION ............................................................74 THE PC CARD CANNOT BE RECOGNIZED .............................................74 WINDOWS CRASHES OR FREEZES WHEN YOU REMOVE THE PC CARD ...74 THE COMPUTER BECOMES HOT ..........................................................75 THE PROGRAM APPEARS STOPPED OR RUNS VERY SLOWLY .................75 THE USB DEVICE DOES NOT WORK ....................................................75 SPECIFICATION .....................................................................................77

2 BBeeffoorree yyoouu SSttaarrtt Conventions of This Manual Use this manual will help you get the most from your notebook computer. ¾ If you are an experienced user of computers and/or Microsoft’s Windows operating systems, you might find it useful to read the Quick Start Guide that comes along with your accessories. ¾ If you are a less experienced user, you should through the manual carefully before using your system. Whether or not you are an experienced user, you should consult on the Troubleshooting Chapter if you encounter any problems with your notebook. Safety Precautions This section is designed to assist you in identifying potentially unsafe conditions while working with this product. Required safety features have been installed in the computer to protect you from injury. However, you should use good judgment to identify potential safety hazards: 1. Please read these safety instructions carefully. 2. Please keep this User's Manual for later reference. 3. Please disconnect this equipment from AC outlet before cleaning. Don't use liquid or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning. 4. For pluggable equipment, that the socket-outlet shall be installed near the equipment and shall be easily accessible. 5. Please keep this equipment from humidity. 6. Lay this equipment on a reliable surface when installed. A drop or fall could cause injury.

3 7. Make sure to use the right voltage for the power source when connecting the equipment to the power outlet. 8. Place the power cord in such a way that people can not step on it. Do not place anything on top of the power cord. 9. All cautions and warnings on the equipment should be noted. 10. If the equipment is not use for a long time, disconnect the equipment from the main power outlet to avoid being damaged by transient overvoltage. 11. Never pour any liquid into the opening, this could cause fire or electrical shock. 12. Never open the equipment. For safety reason, the equipment should only be opened by a qualified service personnel. 13. If on the following situations arises, get the equipment checked by a service personnel: a. The Power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment has not worked well or you cannot get it work according to the user's manual. e. The equipment has dropped and damaged. f. If the equipment has obvious sign of breakage. 14. Do not leave this equipment in an environment unconditioned, storage temperature above 60°C (140°f), it may damage the equipment. 15. The unit can be operated at an ambient temperature of max. 35°C. 16. The sound pressure level at the operators position according to IEC 704-1: 1982 is equal or less than 70 dB(A). 17. Power Cord Requirements The power cord set used with the AC adaptor must meet the requirements of the country where you use the AC adaptor, whether it is 100-120 or 200-240 Vac. The following information explains the requirements for power cord set selection.  The cord set must be approved for the country in which it is used.  The appliance coupler must have a configuration for mating with a CEE7/EN60320/IEC 320/NEMA/ JIS C 8303 appliance inlet. A. For U.S. and Canada:  The cord set must be UL Listed and CSA Certified.

4  The minimum specifications for the flexible cord are No. 18 AWG, (2) Type SPT-2, and (3) 2-conductor. B. For Japan:  All components of the cord set must bear a “PSE” mark and in accordance with the Japanese Dentori Law.  The minimum specifications for the flexible cord are .75m ㎡ conductors, (2) Type VCTR or VCTFK, and (3) 2-conductor.  The cord set must have minimum rated current capacity of 7 A.  The attachment plug must be a two-pole, grounded type with a Japanese Industrial Standard C8303 (15 A, 125 VAC) configuration. C. For Other Countries:  The cord set fittings must bear the certification mark of the agency responsible for evaluation in a specific country.  The flexible cord must be of a HAR (harmonized) type H03VVH2-F.  The cord set must have a current capacity of a least 2.5 Amperes and voltage rating of 125 or 250 Vac. CAUTION: MODEL U10IL1(x=0~9) IS DESIGNED TO USE WITH THE FLLOWING AC ADAPTER MODEL ONLY Manufacture: Dee Van Enterprise Co., Ltd. Model: DSA-30PFA-19US (30W) Model: DSA-30PFA-19UK (30W) Model: DSA-30PFA-19EU (30W) Model: DSA-30PFA-19CH (30W) Manufacture: Delta Electronics, Inc. Model: ADP-40PH AB (40W) Manufacture: Lite-on International Enterprise Corp. Model: PA-1400-11 (40W) 18. When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons. These precautions includes the following: ¾ Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

5 ¾ Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. ¾ Do not use the telephone to report a gas leak in the vicinity of the leak. ¾ Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special instructions. 19. Do not use the AC adapter near open water or other liquids. Never spill liquid into the AC adapter. 20. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Never remove the battery pack while the power is on as this may result in data loss when the system loses power. 21. The input receptacle is used as the main disconnecting device. This part is hot. Be careful. Wichtige Sicherheitshinweise 1. Bitte lesen Sie diese Hinweis sorgfältig durch. 2. Heben Sie dirse Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Versenden Sie Keine Flüssig- oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung. 4. Die Netzanschluβsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Beschädigungen hervorrufen. 7. Beachten Sie beim Anschluß an das Stromnet die Anschlußwerte. 8. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch nichts auf der Leitun abgestellt werden. 9. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten. 10. Wird das Gerät üeinen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit wird im Falle

7  Die Minimalanforderungen für das Kabel entsprechen No. 18 AWG. (2) Type SPT-2, und (3) 2-conductor. B. Für Japan:  Alle Teile des Kabel-Sets müssen entsprechend dem japanischen Dentori Law mit einem „PSE“ markiert sein  Die Minimalanforderungen für das Kabel sind .75m ㎡ Leiter. (2) Type VCTF oder VCTFK, und (3) 2-conductor.  Der Kabelsatz muss mindestens für eine Stromstärke von 7A geeignet sein.  Der Wandstecker muss ein zweipoliger geerdeter Steckertyp gemäß dem Japanese Industrial Standard C8303 (15A, 125 VAC) sein. C. Für andere Länder:  Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel derjenigen Stelle, die in dem jeweiligen Land für die Sicherheitsprüfung zuständig ist, tragen.  Das Kabel muss vom HAR (harmonisierten) Typ H03VVH2-F sein.  Das Kabel-Set muss eine Stromkapazität von mindestens 2,5 Ampere haben und Spannungen von 125 oder 250 V Wechselstrom gestatten. ACHTUNG: Mit dem U10IL1(x=0~9) muss ein AC-Adapter folgenden Modells verwendet werden Hersteller: Dee Van Enterprise Co., Ltd. Modell: DSA-30PFA-19US (30W) Modell: DSA-30PFA-19UK (30W) Modell: DSA-30PFA-19EU (30W) Modell: DSA-30PFA-19CH (30W) Hersteller: Delta Electronics, Inc. Modell: ADP-40PH AB (40W) Hersteller: Lite-on International Enterprise Corp. Model: PA-1400-11 (40W) 18. Bei der Benutzung Ihres Telefongerätes sollten Sie immer die grundlegenden Sicherheitsmaßnahmen beachten, um das Risiko von Feuer, Stromschlägen und Verletzungen zu minimieren. Zu beachten sind u.a. folgende Punkte:

8 ¾ Benutzen Sie das Gerät nicht in der Nähe von Wasser, wie zum Beispiel Badewanne, Waschbecken, Spülbecken, Waschbottich, in feuchten Kellerräumen oder in der Nähe von Schwimmbecken. ¾ Benutzen Sie kein Telefon (ausgenommen schnurlose Modelle) während eines Gewitters. Es besteht das geringe Restrisiko eines Blitzschlages. ¾ Benutzen Sie das Telefon nicht um ein Gasleck zu melden, falls es sich in der Nähe des Lecks befindet. ¾ Verwenden Sie nur die in diesem Benutzerhandbuch angegebenen Stromkabel und Batterien. Werfen Sie die Batterien nicht ins Feuer, sie könnten explodieren. Informieren Sie sich über die örtlichen Bestimmungen bezüglich der Entsorgung. 19. Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu Wasser oder anderen Flüssigkeiten. Gießen Sie nie Flüssigkeiten über das Netzteil. 20. Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß ersetzt wird. Ersetzen Sie den Akku nur durch einen Akku gleichen oder äquivalenten Typs, der vom Hersteller empfohlen wird. Entsorgen Sie Akkus entsprechend den Anweisungen des Herstellers. Entfernen Sie den Akku auf keinen Fall bei eingeschaltetem notebook, da hierdurch Daten verloren gehen könnten. 21. Der Netzeingabeanschluss dient als Hauptschalter des Geräts. Things you must remember before working on your computer Let your computer acclimate itself Your notebook can easily stand temperature extremes but it doesn’t like rapid changes in temperature, like going from the cold outdoors to a warm office. Rapid changes in temperature can cause water droplets to condense inside your case, threatening to damage the electronic parts inside. After receiving your notebook when it’s hot or cold outside, try not to power up the computer immediately, let the computer adjust to the room temperature gradually at least for three to four hours. If your system arrives in cold

9 weather, do not apply power to the computer or monitor until they have been allowed to come to room temperature. Heat, Cold, Humidity, and Glare Find a suitable place for your computer that’s not too hot, too cold, too dark, or too bright. Glare can make it hard to read the screen. ¾ Try to avoid the computer components from being destroyed if it is over heated, so try to allow plenty of room for air to circulate around the case. ¾ Do not block the ventilation opening. ¾ Do not place your computer in direct sunlight. Suitable place to work Your computer will run well wherever you’re comfortable but extremes of temperature and humidity can be challenging to your system’s parts. There are some things you can tolerate that the computer can’t – things like static electricity, dust, water, steam and oil. In case you decide to pull over for roadside computing, try to choose a clean, comfortable work area for your system. A lithium-ion battery pack will be available when you are traveling. If you are running your system for the first time on battery power, remove the battery from the package, install it into the system and recharge the battery to fully prepare for service.

11 IInnttrroodduuccttiioonn Preparing your Computer 1. Install the battery pack 2. Connecting the AC adapter 3. Opening the display panel 4. Turning on your computer Knowing your Computer With the LCD screen open, you will see several features important for operating your notebook computer.

12 To avoid damage to the display panel: 1. Try not to slam the display upon closing it. 2. Try not to place any object on top when it is closed or open. 3. Be sure the system is turned off or in suspend mode before you close the display panel. Front View

13 1. Camera 2. LCD Display This LCD panel can only support up to a maximum opening of 130-135 degrees, please do not push it forcibly. 3. Built-in Speaker 4. Keyboard The keyboard differs for each territory 5. Power / Suspend Button ¾ Press for 1~1.5 seconds to turn on the system. ¾ Press and hold for at least 4 seconds to turn off the system. ¾ Press the power / suspend button again to return from the suspend mode. ¾ Persistent blue light indicates the Power is ON 6. Touchpad 7. Touchpad Buttons 8. LED Status Indicator System & Power Status Indicators

14 LED Graphic Symbol Indication Green light indicates the system is ON. Blinking blue light indicates the notebook is in suspend mode. Green light indicates the WLAN/Bluetooth/HSPA is active. Battery status Charging – Orange Full – Green Low – Red Blue light indicates the hard drive and/or optical drive is being accessed. Left Views

15 1. Modem Port (Optional) Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment. To reduce the risk of fire use only No. 26 AWG or larger telecommunication line cord. 2. DC In 3. Ethernet / LAN Port When using a LAN, please use an EMI Shielding Cable to minimize an inteference when transmitting. 4. CRT Port 5. Enhanced USB 2.0 Port This strengthen USB power sourse for the USB port, the function lets users when using any other major big power consumption USB device in avoiding creating any harm to the USB port. When using any External USB Device, only use the approve cable provided by the manufacturer. Using other cable where it affect the current flow will cause undetermined damage. Not suitable to use any 3.5” or 5.25” USB ODD or HDD 6. USB 2.0 Port 7. Microphone/Audio Line-in Jack 8. Stereo Headphone Jack

16 Right View 1. USB 2.0 Port 2. Kensington Lock

17 Bottom View 1. Battery Release Latch 2. Internal Microphone 3. Battery Compartment 4. Battery Lock

19 GGeettttiinngg SSttaarrtteedd Connecting to a Power Source Connecting the AC Adapter A universal AC adapter is provided to supply your computer with power and also charge the computer’s battery pack. The adapter’s AC input voltage can range anywhere from 100 to 240 volts, covering the standard voltages available in almost every country. To connect the computer to an external power source: Do not use inferior extension cords as this may result in damage to your notebook. The notebook comes with its own AC adapter. Do not use a different adapter to power the computer and other electrical devices.

20 Whenever possible, keep the AC adapter plugged into the notebook and an electrical outlet to recharge the battery. Never turn off or reset your notebook while the hard disk is in use status icon is lit; doing so can result in loss or destruction of your data. Always wait at least 5 seconds after turning off your notebook before turning it back on; turning the power on and off in rapid succession can damage the notebook’s electrical circuitry. Turning On Your Notebook Computer Hold the button down for a second or two and release. The Power-On Self Test (POST) runs automatically. After the POST is completed, the computer reads the operating system from the hard disk drive into computer memory (this is commonly referred to as “booting” a computer). If your OS (Operating System such as Windows XP…. etc) is installed, it should start automatically. To turn the notebook off, save your work and close all open applications, click on Start, then Shut Down and select Shut down the computer and click "Yes" or press the power button for 4-6 seconds. Operating on Battery Power Your computer comes with a rechargeable battery pack that lets you operate the computer without an external power source. When the battery pack is fully charged, you can operate the computer under the following conditions: ¾ The battery pack initially has a full charge. ¾ No peripheral devices are installed. Only use batteries that are approved by an authorized dealer. All batteries are not the same and therefore should not be treated as such. Using the wrong battery could cause serious damage to your computer and yourself through toxic emissions. Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used

21 batteries according to the manufacturer’s instructions or local laws. Explisionsgefahr bei unsachgernazen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des Herstellers. Installing and Removing the Battery Pack To Install the Battery Pack:

22 To Remove the Battery Pack: Charging the Battery Pack The installed battery pack charges automatically any time the computer is connected to the AC adapter and an external power source. It is a good idea to occasionally discharge the battery pack fully to preserve its operating performance.

24 UUssiinngg tthhee NNootteebbooookk CCoommppuutteerr Adjusting the LCD Screen Display The LCD screen display can be adjusted by the following key combinations. + - Changes Display Mode: LCD-only, CRT-only, LCD/CRT simultaneously + - Increases the brightness level. + - Decreases the brightness level. LCD Care LCD screens are delicate devices that need careful handling. Please pay attention to the following precautions: ¾ When you are not using the computer, keep the LCD screen closed to protect it from dust. ¾ If you need to clean your LCD screen, use a soft tissue to gently wipe the LCD surface. ¾ Do not put your fingers or sharp objects directly on the surface and never spray cleaner directly onto the display. ¾ Do not press on, or store any objects on the cover when it is closed. Doing so may cause the LCD to break.

25 External CRT Display You can hook up an external monitor through the 15-pin CRT connector. Three configurations are available: ¾ LCD only ¾ CRT only ¾ LCD and CRT simultaneously You can switch between these display configurations by pressing the key combination [Fn] + [F4]. The Notebook’s Hot Key Controls Function Keys (Quick Keys) + - Bluetooth on/off. + - Enters the Suspend Mode. + - HSPA on/off + - WLAN on/off + - Changes Display Mode: LCD-only, CRT-only, LCD/CRT simultaneously + - Increases the speaker volume.

26 + - Decreases the speaker volume. + - Increases the brightness level. + - Decreases the brightness level. + - Enable/Disable the Touchpad + - Mute the system volume + - Enable/Disable the silent mode + - Enable/Disable the camera application On Screen Display (OSD) OSD (On Screen Display) provides you an easy access to the function key you normally use in executing some of the application you would like to perform. Other alternative is by executing the hot key combination we provide which is imprinted on the upper portion of the keyboard. After you activate the function key, the icon will be shown at the upper right hand corner of your window screen. Screen Display Icon T/P On/Off or Fn + F9 WebCam On/Off or Fn + F12 Silent Mode On/Off

27 Caps Locks Num Locks Scroll Locks WLAN On/Off or Fn + F3 BlueTooth On/Off or Fn + Esc 3G On/Off or Fn + F2 Brightness or Fn + F7/Fn + F8 Mute On/Off or Fn + F10 Volume or Fn + F5/Fn + F6 Previous Play/Pause Next Stop Fast Forward Rewind Web Browser

28 OSD-Bar Icon Caps Locks On Num Locks On Scroll Locks On Silent Mode ON Touchpad Off WLAN On Web Cam On Bluetooth On Mobile Broadband On The OSD bar can be shown on the side bar or you can drag it anywhere either on top (horizontally) or on the sides (vertically) of your screen. Horizontally Top or Bottom Vertically Right or Left Live Power (Optional) Live Power is a saving scheme technique that provides saving your battery consumption by disabling some devices thus extending the battery life. Click on the Live Power icon from the lower right bar of your screen to open up the Live Power Display. The Live Power provides five modes according to the application that you are executing: ¾ Power saving mode: Provides the low consumption function, suitable for low utilization ratio and suspend mode.

29 ¾ Normal mode: Provides for general work status. ¾ High Performance mode: For highest efficiency condition. ¾ DVD player mode: Provide for watching movie playback. ¾ Dynamic mode: For system power utilization mode, switching the CPU loading and battery life to appropriate mode. This Live Power application provides a super saving options if the following items are selected: Enable advance power saving engine The system will take over and switch to an appropriate power mode automatically. How the system manages with the switching will depend on the models that you are using. Power Off LCD panel When the system is powered by the battery and the CPU loading is low, the LCD panel will be powered off to save the battery consumption after a 10-minutes interval with no operation from your system and USB-attached keyboards, mouse, touchpad, Webcam, and any DVD player software like Media player.

30 Power Saving Mode LCD Brightness: Level 1 LCD Off: Idle after 5 minutes HDD Off: Idle after 3 minutes Sleep: Idle after 5 minutes Hibernate: Idle after 10 minutes Normal Mode LCD Brightness: Level 5 LCD Off: Idle after 15 minutes HDD Off: Idle after 30 minutes Sleep: Idle after 1 hour Hibernate: Idle after 2 hours

31 High Performance Mode LCD Brightness: Level 5 LCD Off: Never HDD Off: Never Sleep: Never Hibernate: Never DVD Play Mode LCD Brightness: Level 5 LCD Off: Idle 4 hours HDD Off: Idle after 4 hours Sleep: Idle after 1 hour Hibernate: Idle after 2 hours

32 Dynamic Switch Mode CPU Loading High Middle plus Middle Low Battery life% 50% up 30% up 4%up <4% level 5 90% up High Performance mode High Performance mode High Performance mode Normal mode level 4 50% up High Performance mode High Performance mode Normal mode Normal mode level 3 30% up High Performance mode Normal mode Normal mode Power Saving mode level 2 15% up Normal mode Normal mode Power Saving mode Power Saving mode level 1 6% up Normal mode Power Saving mode Power Saving mode Power Saving mode level 0 less than 5% Power Saving mode Power Saving mode Power Saving mode Power Saving mode The CPU load is automatically shown on the application display indicating the power saving mode.

33 The TouchPad The touchpad is a rectangular electronic panel located just below your keyboard. You can use the static-sensitive panel of the touchpad and slit it to move the cursor. You can use the buttons below the touchpad as left and right mouse buttons. TouchPad Precautions The TouchPad is a pressure sensitive device. Please take note of the following precautions. ¾ Make sure the TouchPad does not come into contact with dirt, liquids or grease. ¾ Do not touch the TouchPad if your fingers are dirty. ¾ Do not rest heavy objects on the TouchPad or the TouchPad buttons. You can use the TouchPad with Microsoft Windows as well as non-Windows applications. Power Saving Modes This section contains information on the notebook’s power system, including the AC Adapter, the battery system, recharging the battery, and tips for conserving battery power. The power system is comprised of two parts, the AC Adapter and the battery system. The AC Adapter converts AC power from a wall outlet to the DC power required by the computer.

34 The Battery Power System Before using the computer on battery power for the first time, check the battery status icon on the Windows Toolbar to make sure the battery is fully charged. See Battery Status later in this section for a description and explanation of the Windows Battery icon. Charging the battery takes about 2.5 hours to charge when the system is in off state. If possible, always charge the battery completely. If you use the battery so frequently that it exceed more than 20 times by fully discharging/charging in a single month alone, we recommend you to perform the “Battery Calibration” process every 3 months to maintain the battery life. Please refer to the topic on “Battery Calibration” describing how to calibrate your system battery discussed on the latter part of this chapter. If you discover the battery life is getting shorter, please perform the “Battery Calibration” process immediately. Removing the Battery Pack To remove the battery pack from its compartment, please refer to Chapter 3, Inserting and Removing the Battery Pack. Preparing the Battery Pack for Use (Battery Calibration) Before using the battery pack for the first time, the Smart Battery IC within the battery pack should be calibrated in order to get accurate reporting of remaining battery life status. To calibrate the battery pack follows the instructions below: 1. Insert the battery into the battery compartment and turn on the notebook. If the battery is completely without power go to the next step. Otherwise, let the battery run down until the battery low-low warning beeps are heard. The system will automatically enter Suspend mode. 2. Turn the notebook off. Connect the AC adapter and let the battery fully recharge. When the battery charge indicator turns off, the battery is fully charged.

35 3. Turn On the notebook, let the battery run down until the battery is in low-low state and you hear a warning beeps. The system will automatically enter the Suspend mode. You can now connect the AC adapter. 4. The battery pack is now calibrated properly. In general, using the battery until the low-low battery-warning indicator appears and fully recharges the battery each time (full discharge/charge cycle) will ensure the accurate reporting of the battery gauge status. Automatic Battery Pack Charging Function To charge the battery, while the battery pack is in the notebook, plug the AC adapter into the notebook and an electrical outlet. The charging time is approximately 2.5 hours when the notebook is turned off and approximately 3.5 hours when the notebook is turned on. When the battery is fully charged, the battery charge indicator becomes off. If system runs at heavy loading or in a high temperature environment, the battery may not be fully charged. You need to continue to charge it with the AC adapter plugged in until the charging LED turns off. Battery Status Windows XP has an applet in the Control Panel that will display an icon in the Windows taskbar indicating when the notebook is running on battery power or is attached to the AC adapter. This applet also displays a meter that indicates how much charge is remaining in the battery. Battery Low Warning When the pack initially reaches the “Battery Low” state approximately 7 ~ 10 minutes of the usable battery life is left. You will hear an audible beep signal every 15 seconds alerting you to the “Battery Low” status. When the battery power reaches the “Battery Low Low” status the beeping sound will accelerate. Your battery now has 1 ~ 2 minutes of battery charge remaining. You must save your data or connect AC power immediately; otherwise, you may lose your data.

36 Sound Meaning Continuous beeping every 5 seconds Battery Low: Indicates that there is 7 to 10 minutes charge remaining. Beeping accelerates Battery Low Low: Indicates that there is 1 to 2 minutes of battery charge remaining. Save your work and turn off the notebook, or connect the AC adapter. When there is only one minute of battery charge remaining, the notebook will suspend to the HDD and power off. You should connect AC power and resume to save your work. Small Battery for the Real Time Clock There is a small built-in battery pack that supplies power to the system in order to maintain certain system information while the power is off. If the notebook is left without a power source for long period of time, this battery will be exhausted and system information will be lost. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Never remove the battery pack while the power is on as this may result in data loss when the system loses power. Resetting the System After installing a software application package, you may be prompted to reset the system to load the changed operating environment. To reset the system, or “reboot,” press the [Ctrl]+[Alt]+[Delete] keys simultaneously. This is known as “warm boot.” This key combination acts as “software” reset switch when you encounter hardware or software problems, which lock up the notebook. If this key combination does not shut down the notebook, you can reset the notebook by using the notebook’s power button. Should the notebook lock up for some reason, pressing this button powers the notebook off.

37 Adjusting the Brightness To adjust the brightness on the LCD screen, press and hold down the [Fn] key in the lower left hand corner of the keyboard and press the [F8] key to reduce the brightness or [F7] to increase the brightness. Using the Windows Help Windows For Windows XP help, click Start ÎHelp and Support icon will open the dialog box. Desktop Desktop may vary differently on the software installed in your notebook with different or additional shortcuts.

38 Recycle Bin Used for storing deleted files in case you want to recover and save it in your system. The files will only be deleted from the Recycle Bin permanently only if you empty it by right clicking your mouse and select the “Empty Recycle Bin”. Start Button Allows easy access to all Windows programs.

39 The Start menu allows you to adapt and show the programs used most frequently. If you wish to keep an item, right click the item and click Pin to Start menu. Log Off will enable the current user to log off and allows a new user to log on. Turn Off Computer allows you to shut down, restart, and Stand by modes for power saving purposes. Taskbar When you open a program, its icon is displayed at the taskbar for you to conveniently move between programs by clicking the relevant button. To add or remove toolbars from the taskbar: right click an empty spot on the taskbar, select Toolbars Î choose the toolbar you want to add.

40 Notification The icons that appear here are for quick access to some programs and computer functions that you frequently used. To prevent Windows XP from hiding icons: From an empty spot on the Taskbar, right click your mouse and select the Properties, remove the checked mark on the Auto-hide the taskbar. Control Panel It is in this area that you can change how Windows looks and works. Click Start Î Control Panel dialog box. There are two interfaces – Classic View.

43 IInntteerrnneett CCoonnnneeccttiioonn There are numerous ways to connect to the Internet. This may vary from the user’s working environment as well as system specifications. ¾ Using a modem and a telephone line (optional) ¾ Using a wired LAN ¾ Using a wireless LAN ¾ Bluetooth Connection Using a modem for Connection to Internet (optional) ¾ Use a telephone line to connect to the modem port of your computer. Do not use a digital telephone line. ¾ Please apply to an Internet Service Provider (ISP) for Internet service in order for you to connect the modem to the Internet and use e-mail. For more detail on the Network key, please refer to your local ISP provider and follow the procedures describe in the “ISP Installation Guide” to proceed with the installation. Using a wired LAN for Connection to Internet For you connect to the Internet, a wired LAN environment normally uses the company’s LAN or a broadband modem.

45 Using Wireless LAN Network for Connection to Internet Bluetooth Connection Bluetooth is a developing, world wide, open, short-range radio specification focused on communication between the Internet and Net devices, plus it defines communication protocols between devices and computers. It connect wirelessly to your world: In home, at work, in motion and at play. Access the internet or your e-mail account from anywhere, anytime.

46 Press on the Bluetooth icon to connect other devices that have this application. This will be the display that will appear on your screen. If the system detects any other devices, it will be shown as illustrated in the Bluetooth setting window:

48 RRuunnnniinngg BBIIOOSS SSeettuupp The Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output System). It runs and maintains a variety of hardware functions. It is menu-driven software, which allows you to easily configure and change the settings. The BIOS contains manufacture’s default settings for the computer’s standard operations. However, there are occasions when you may be required to modify the default settings in the BIOS. The BIOS allows you to set up passwords to limit access to users. This is an important feature because a great deal of vital information is carried within the computer nowadays. Unauthorized access can be prevented. Later in this chapter, you will learn how to use this security feature. Entering the BIOS Setup Screen First turn on the power. When the BIOS performs the POST (Power-On Self Test), press DEL key quickly to activate the BIOS Setup Utility. You may need to press DEL key fairly quickly. Once the system begins to load Windows, you may have to retry by cycle-power on again Leaving the BIOS Setup Screen When you have finished modifying the BIOS settings, exit the BIOS. It takes a few seconds to record changes in the CMOS.

49 BIOS Action Keys Function Key Command Description ESC Exit Leaves a sub-menu to return to the previous menu OR exits the BIOS setup while saving changes. F1 General Help Shows the Help Screen F10 Save and Exit Saves changes and reboots the computer. <Tab> Select a field Selects the next field. ↑ Select an item Selects the next upper item. ↓ Select an item Selects the next lower item. - Lower value Selects the next value within a field. + Higher value Selects the next value within a field. Modifying the BIOS Settings The BIOS setup main menu is subdivided into sub-menus. Each menu item is described in this section. Main Setup Under this menu, you may change time/date and view basic processor and system memory information.

50 Info Setup

51 Advanced Setup Security

52 Power Setup Boot Setup

53 Exit Setup System Recovery When you start to use this notebook, kindly make a rescue disk by “System Recovery AP” to back up your disk.” This application can be activated by: From “Start”, click on the “System Recovery This process enables you to restore your system whether your system is damaged or for some other reason that you can not operate your computer. First turn on the power. When the BIOS performs the POST (Power-On Self Test) ¾ Press F9 key quickly to activate the System Recovery Program.

54 ¾ Or click the “Quit” if you want to discontinue with the application. ¾ Click the “Recover your computer” if you want to proceed.

55 ¾ You will be asked whether you would like to proceed with the recovery procedures. ¾ Click “OK” if you want to proceed or “Cancel” if you want to discontinue with the recovery procedures. This illustration will be shown twice after you made the first decision in case you change your mind to discontinue with the recovery procedures. ¾ The system will start with the recovery procedures.

56 ¾ This illustration indicates the system has finished with the recovery procedures.

58 VVGGAA UUttiilliittiieess You can click the touchpad or mouse right button and select the “Properties” item. Select the “Display Settings” option to enter its window display. Click on the “Advanced Settings” tab to enter “Plug and Play Monitor on Mobile Intel ® 945 Express Chipset Family” window display.

61 Display Devices Display Settings

62 Color Correction Hot Keys

64 33GG CCoonnnneeccttiioonn 3G is the third generation of mobile phone standards and technology. 3G enable users a wide range of more advanced service while achieving greater network capacity through improved spectral efficiency.

65 Press the hot key combination of Fn + F2 to start executing the application. Procedures in installing the application ¾ Insert the SIM card into the SIM slot. ¾ Execute the application by pressing the Mobile Partner icon ¾ From the Mobile Partner display window, click on the “Tools” item ¾ Select the “Options”.

67 ¾ On the next window, click on the “Connect” tab. ¾ The HSPA is successfully connected

69 TTrroouubblleesshhoooottiinngg Your computer has been fully tested and complies with the system specifications before shipping. However, incorrect operations and/or mishandling may cause problems. This chapter provides a reference for identifying and correcting common hardware and software problems that you may encounter. When you encounter a problem, you should first try to go through the recommendations in this chapter. Instead of returning the computer and waiting for repair, you may easily solve the problems by considering the following scenarios and possible solutions. If the error continues, contact your reseller for service information. Before taking further actions, consider the following suggestions: ¾ Check to see if the problem persists when all the external devices are removed. ¾ Check to see that the green light indicator on the AC adapter is lit. ¾ Check to see the power cord is properly plugged to the wall outlet and to the computer. ¾ Check to see the power indicator of the computer is on. ¾ Check to see if your keyboard is operational by pressing and holding any key. ¾ Check for any incorrect or loose cable connections. Make sure the latches on the connectors latch securely on to the receptor end. ¾ Be sure you have not performed an incorrect setting on the hardware devices in the BIOS Setup utility. A faulty setting may cause the system to misbehave. If you are not sure of the changes you made, try to restore all the settings to factory defaults.

70 ¾ Be sure all the device drivers are installed properly. For example, without the audio driver properly installed, the speakers and microphone will not work. ¾ If external devices such as USB camera, scanner, printer do not function correctly when connected to the system, it is usually the device’s own problem. Consult the device’s manufacturer first. ¾ Some software programs, which have not gone through rigorous coding and testing, may cause problems during your routine use. Consult the software vendor for problem solving. ¾ Legacy peripheral are not plug-and-play capable. You need to restart the system with these devices powered up and connected first. ¾ Be sure to go to BIOS SETUP and load DEFAULT SETTING after BIOS re-flash. ¾ Be sure the Quick Key Lockout Switch on the bottom of the computer is not engaged; otherwise the quick keys will not work. Audio Problems No speaker output ¾ Software volume control is turned down in Microsoft Sound System or is muted. Double-click the speaker icon on the lower right corner of the taskbar to see if the speaker has been muted or turned down all the way. ¾ Most audio problems are software-related. If your computer worked before, chances are software may have been set incorrectly. ¾ Go to [Start > Settings > Control Panel] and double-click the Sounds and Audio Devices icon. In the Audio page, make sure that the audio codec mentioned in the spec is the default playback device. Sound cannot be recorded ¾ You will need to plug-in an external microphone to the microphone connector to record sound. ¾ Double-click the speaker icon on the lower right corner of the taskbar to see if the microphone has been muted. ¾ Click Options and select Properties. ¾ Select Recording and click the OK button.

71 ¾ After Click OK button, the recording volume control panel will appear. ¾ Go to [Start > Settings > Control Panel] and double-click the Multimedia icon (or Sounds and Audio Devices icon). In the Volume or Audio page, make sure that the audio codec mentioned in the spec is the default recording device. Hard Disk Problems The hard disk drive does not work or is not recognizable ¾ If you had just performed a hard disk upgrade, make sure the hard drive connector is not loose and the hard disk drive is also correctly seated. Remove it and reinsert it firmly, and restart your PC. ¾ The new HDD may need to be partitioned and reformatted. O/S and drivers will need to be re-installed as well. ¾ Check the hard disk indicator LED. When you access a file, the LED lamp should light up momentarily. ¾ The new HDD may be defective or is not compatible. ¾ If your computer has been subjected to static electricity or physical shock, you may have damaged the disk drive. The hard drive is making abnormal whining noises ¾ You should back up your files as soon as possible. ¾ Make sure the source of noise is indeed from the hard drive and not the fan or other devices. The hard disk drive has reached its capacity ¾ Run Disk Cleanup utility in Windows. [Start > All Programs > Accessories > System Tools > Disk Cleanup] The system will prompt you for what to do. ¾ Archive files or programs that you had no longer used by moving them to an alternative storage medium (floppy disk, optical record-able disk, etc.) or uninstall programs that no longer use. ¾ Many browsers store files in the hard drive as a cache to speed up the performance. Check the program’s Online Help for instructions on decreasing the cache size or on removing temporary Internet files. ¾ Empty the Recycle Bin to create more disk space. When you delete files, Windows saves them to the Recycle Bin.

72 The hard disk takes longer to read a file ¾ If you have been using the drive for a period, the files may be fragmented. Go to [Start > Programs > Accessories > System Tools > Disk Defragmenter] to perform a disk defragmentation. This operation may take a while. ¾ Interrupt requests or problems with other hardware devices may have occupied the CPU and therefore slows down the system performance. The files are corrupted ¾ Run the Error-checking utility in Windows to check the HDD. Double-click My Computer. Right-click C: and select Properties. Click Check Now in Error-checking in Tools. Display Problems The display panel is blank when the system is turned on ¾ Make sure the computer is not in the Standby or Hibernate suspend modes. The display is turned off to conserve energy in these modes. The screen is difficult to read ¾ The display resolution should at least be set to at least 1024x600 for optimal viewing. ¾ Go to [Start > Settings > Control Panel] and double-click the Display icon. ¾ Under the Settings page, set screen resolution to at least 1024x600. The screen flickers ¾ It is normal if the display flickers a few times during shutting down or powering up. Keyboard and Mouse Problems The built-in touch pad performs erratically ¾ Make sure there is no excess perspiration or humidity on your hand when using the touch pad. Keep the surface of the touch pad clean and dry.

73 ¾ Do not rest your palm or wrist on the surface of the touchpad while typing or using the touch pad. The built-in keyboard accepts no input ¾ Please try to make sure the system doesn’t hang up and is still working. The characters on the screen repeat while I type ¾ You may be holding the keys down too long while you’re typing. ¾ Keep the keyboard clean. Dust and dirt under the keys could cause them to stick. ¾ Configure the keyboard to wait longer before the auto repeat feature starts. To adjust this feature, Go to [Start > Settings > Control Panel], and double-click the Keyboard icon. A dialogue box shows up with the adjustable settings for the keyboard. CMOS Battery Problem A message “CMOS Checksum Failure” displays during the booting process or the time (clock) resets when booting ¾ Try to reboot the system. ¾ If the message “CMOS Checksum Failure” appears during the booting procedure even after rebooting, it may indicate failure of the CMOS battery. If so, you need to replace the battery. This battery normally lasts two to five years. The battery is of type CR2032 (3V). Send the battery to the dealer for replacement. Memory Problems The POST does not show an increased memory capacity when you have already installed additional memory ¾ Certain brands of memory module may not be compatible with your system. You should ask your vendor for a list of compatible DIMM. ¾ The memory module may be defective.

74 The O/S issues an insufficient memory error message during operation ¾ This is often a software or Windows-related problem. A program is draining the memory resources. ¾ Close the application programs you’re not using and restart the system. PC Card Problems Some system may not have the PC Card Slot option. PC Cards do not function ¾ Make sure you have properly installed the driver for the card. ¾ Consult the card’s manual or contact the vendor for trouble-shooting. The PC card cannot be recognized ¾ Make sure the card is fully inserted; the outer end of the card should be even with the edge of the computer. ¾ Remove and insert the PC card again. ¾ Make sure there is no IRQ conflict with the card. See Windows on-line help for solving IRQ conflicts. ¾ Reboot the computer and see if the problem persists. ¾ The card may be defective. Try the card on another system, if possible. Windows crashes or freezes when you remove the PC card ¾ Make sure you have <Stop> the PC card before removing it. Double-click the Safely Remove Hardware icon at the lower right corner of the task bar and select the card you wish to stop. When you click <Close>, in few seconds Windows will prompt you to remove the card.

75 Performance Problems The computer becomes hot ¾ In a 35oC environment, the certain areas of the computer’s back case are expected to reach 50 degrees. ¾ Make sure the air vents are not blocked. ¾ If the fan does not seem to be working at high temperature (50 degrees Celsius and up), contact the service center. ¾ Certain programs that are processor-intensive may increase the computer temperature to a degree where the computer automatically slows down its CPU clock to protect itself from thermal damage. The program appears stopped or runs very slowly ¾ Press CTRL+ALT+DEL to see if an application is still responding. ¾ Restart the computer. ¾ This may be normal for Windows when it is processing other CPU-intensive programs in the background or when the system is accessing slow-speed devices such the floppy disk drive. ¾ You may be running too many applications. Try to close some applications or increase system memory for higher performance. ¾ The processor may have been overheated due to the system’s inability to regulate its internal heat. Make sure the computer’s ventilation grills are not blocked. USB2.0 Problems The USB device does not work ¾ Check the settings in the Windows Control Panel. ¾ Make sure you have installed the necessary device drivers. ¾ Contact the device vendor for additional support.

77 SSppeecciiffiiccaattiioonn O.S. ¾ Supports Windows XP OS with SATA HDD ¾ Supports Windows Vista Home Basic OS (option) CPU ¾ Atom N270 CPU single core,45 nm, up to 1.6GHz, 512KB L2 Cache, 533MHz FSB, TDP 2.5W ¾ Atom N280 CPU single core,45 nm, up to 1.66GHz, 512KB L2 Cache, 667MHz FSB, TDP 2.5W Memory ¾ DDRII 533/667 support or 667MHz downgrade to 533MHz ¾ RAM socket * 1 ¾ System DDRII up to 1 GB total (2GB option) Core Logic ¾ Intel Calistoga 945GSE+ICH7M VGA ¾ Intel 945GSE Audio Codec ¾ Realtek ALC269 Card reader (4 in 1) ¾ Support SD/SDHC/MMC/MS/MS Pro Memory Card (supports SHDC) ¾ USB2.0 interface

79 ¾ With AMI BIOS and 1MB flash ROM Power Management (default: Silent mode) ¾ “Smart Power II” Power Management Physical Outline ¾ Dimension: ¾ 267 x 192 x 31.1 ~ 35.8mm (w/ rubber foot, 3 cell battery) ¾ 267 x 192 x 29.2 ~ 32.3mm (w/o rubber foot, 3 cell battery) ¾ 267 x 192 x 31.1 ~ 40.1mm (w/ rubber foot, 6 cell battery) ¾ 267 x 192 x 29.2 ~ 39.1mm (w/o rubber foot, 6 cell battery) ¾ Weight – ¾ 1.1Kg w/ 3 cell battery ¾ 1.2Kg w/ 6 cell battery EMI ¾ CE/FCC RF ¾ CE, R&TTE report/document, FCC Safety ¾ CB report/CCC

Navigation menu