Robert Bosch Tool IDX01 GCY Idefix User Manual Briefbogen
Robert Bosch Tool Corporation GCY Idefix Briefbogen
Contents
- 1. InstallationInstruction
- 2. InstallationInstruction RegulatoryNotices
InstallationInstruction RegulatoryNotices
Power Tools To whom it may concern Robert Bosch GmbH Postfach 10 01 56 70745 LeinfeldenEchterdingen Visitors: Max-Lang-Straße 40-46 70771 Leinfelden Tel 0711 758-0 www.bosch.com Applicant / Manufacturer Hardware Robert Bosch GmbH 70745 Leinfelden-Echterdingen Germany Content Regulatory information for FCC for US and IC for Canada for Device name: Manufacturer part number: FCC ID: IC: GCY Idefix 1600A00H6H TXTIDX01 909H-IDX01 Preamble By purchase of any products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Robert Bosch GmbH and Robert Bosch Power Tools GmbH reserve the right to make changes as required without notification. Notice This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux Registered Office: Stuttgart, Registration Court: Amtsgericht Stuttgart, HRB 14000; Chairman of the Supervisory Board: Franz Fehrenbach; Managing Directors: Dr. Volkmar Denner, Dr. Stefan Asenkerschbaumer, Dr. Rolf Bulander, Dr. Stefan Hartung, Dr. Markus Heyn, Dr. Dirk Hoheisel, Christoph Kübel, Uwe Raschke, Dr. Werner Struth, Peter Tyroller 22 June 2016 Power Tools deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Caution & Requirements The FCC requires the user to be notified that changes or modifications made to the equipment not expressly approved by Robert Bosch GmbH and Robert Bosch Power Tools GmbH may void the FCC / IC authorization to operate this equipment. The use of the transceiver module is authorized in mobile or fixed host devices taking into account the conditions listed below: OEM Integrator must ensure that the end user manual may not contain any information about the way to install or remove the module from the final product. Depending on the final host device additional authorization requirements for the non-transmitter functions of the transmitter module may be required (i.e., Verification, or Declaration of Conformity) The OEM integrator is responsible for ensuring that after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements. The information on the label and in the user manual is required to be incorporated in the user manual of the final host. see 47 CFR15 requirements for more details (e.g. 15.19 / 15.21 / 15.101 / 15.105 / RSS-GEN / ICES) Additional label with the words ‘Contains FCC ID:TXTIDX01’ and ‘Contains IC:909H-IDX01’ shall be applied and visible from the outside of the host product. The module must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the module. The end user manual for the final host product operating with this transmitter must include operating instructions to satisfy RF exposure compliance requirements, e.g Radiofrequency radiation exposure Information: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator 22 June 2016 Page 2 of 5 Power Tools and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. The antenna of the module may not be removed, replaced nor modified. The antenna must not be co-located or operating in conjunction with any other antenna or transmitter. No additional antenna must be used. When the final host product operating with this transmitter deviate from above, installation of this module into specific final hosts may require the submission of a Class II permissive change application containing data pertinent to RF Exposure, spurious emissions, ERP/EIRP, and host/module authentication, or new application if appropriate. Device Power Supply The transmitter described in this document is intended to be supplied by an external voltage supply: Either directly with nominal 3V by a CR2032 coin cell via the corresponding “coin cell +/-“ pins and/or with nominal 3.3.V indirectly by a host device via the “ext_pwr” pins. 22 June 2016 Page 3 of 5 Power Tools 22 June 2016 Page 4 of 5 Exemplary block diagram of interface at host device (“BT_3V3” corresponds to “ext_pwr”): Feel free to contact us if additional guidance is required. Yours sincerely Robert Bosch GmbH Power Tools 22 June 2016 Page 5 of 5
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 5 Language : de-DE Tagged PDF : Yes Title : Briefbogen Author : Anja König Creator : Microsoft® Word 2013 Create Date : 2016:10:05 15:50:04+02:00 Modify Date : 2016:10:05 15:50:04+02:00 Producer : Microsoft® Word 2013EXIF Metadata provided by EXIF.tools