Rohde and Schwarz NV830X UHF 1.8kW maximum Digital TV transmitter User Manual 32 SLX8000 12 12 07 01 00

Rohde & Schwarz Inc UHF 1.8kW maximum Digital TV transmitter 32 SLX8000 12 12 07 01 00

Contents

User Manual Part 3

Broadcasting Division2095.7346.32 - 6.0 - E-1CHAPTER 6MAINTENANCEPrinted in Germany
Chapter 6 Maintenance2098.1190.72 - 6.01 - E-3CONTENTS1 Maintenance Intervals ..................................................................... 11.1 Maintenance of Subcontractor Products .....................................................12 Maintenance Tasks .......................................................................... 22.1 Replacing BIOS Battery in R&S NetCCU800 ................................................22.2 Replacing Fans on SX800 Exciter .................................................................22.3 Software Update .............................................................................................2
Chapter 6 Maintenance2098.1190.72 - 6.02 - E-3
Chapter 6 Maintenance2098.1190.72 - 6.1 - E-31 Maintenance IntervalsThe following maintenance work must be performed at regular intervals:1.1 Maintenance of Subcontractor ProductsSubcontractor products such as external air filters must be maintained in accordance withthe maintenance instructions from the respective manufacturer and for the respective prod-uct. Maintenance interval Task Procedure described in:2x per year Check the operating values (e.g. output power, control values, etc) 1x per year Check and, if necessary, change the backup battery of the transmit-ter control unit (R&S NetCCU800)Chapter "Maintenance" in the R&S NetCCU800 manualAfter 5 years and then 1x per yearCheck whether the two rack fans make noises when in operation; replace them if necessaryChapter "Service“ in this man-ualAfter 5 years and then 1x per yearCheck whether the fans make noises when in operation; replace them if necessaryChapter "Maintenance" in the exciter manual
Chapter 6 Maintenance2098.1190.72 - 6.2 - E-32 Maintenance Tasks2.1 Replacing BIOS Battery in R&S NetCCU800Note The chapter "Maintenance" in the R&S NetCCU800 manual describes how to replace theBIOS battery.2.2 Replacing Fans on SX800 ExciterNote The chapter "Maintenance" in the exciter manual describes how to replace the fans.2.3 Software UpdateYou can use the R&S NetCCU800 to install software updates for the R&S NetCCU800 itselfas well as for all exciters connected to the R&S NetCCU800. The update data is first trans-ferred to the R&S NetCCU800. The update for the connected exciters is then performed ina second step.The software update is only possible if the R&S NetCCU800 is remotely connected to a net-work client on which the new software and the program for performing the update are in-stalled. You perform a software update for the NSU/NCU in the same way. It is also possible to up-date exciters via the NCU/NSU Update menu.Note The update program was developed for performing updates of various Rohde&Schwarzsoftware solutions. For this reason, some functions of the program which are not relevantto updating software via the R&S NetCCU800 are omitted in the description below. The procedure for performing a software update is as follows. 1. Log on as Maintenance in the menu operation.2. Call up NetCCU > NetCCU Setup > SW Maintenance. 3. Set the R&S NetCCU800 to Update mode using the Start function under SW UpdateOperation.
Chapter 6 Maintenance2098.1190.72 - 6.3 - E-34. Start the installation software on the client computer. The start window of the R&S Software Distributor opens.5. Confirm the default setting Remote Installation by clicking on Next. The software updates that can be installed will be displayed. You can obtain additionalinformation about the update you select by highlighting it with the cursor and then click-ing Info.
Chapter 6 Maintenance2098.1190.72 - 6.4 - E-36. Select the required updates and confirm installation of the updates by clicking Next.All instruments found in the network are displayed under the device name that you as-signed in the Maintenance menu window.7. Select the instrument and start the update by clicking Install. After the update has been completed, a corresponding message will appear in the fieldat the bottom left of the window. The R&S NetCCU800 is rebooted automatically.If connected transmitter components cannot be found because the R&S NetCCU800 wasnot in Update mode, the message "No R&S Device found" is displayed at the bottom left ofthe window. You have the following option: 1. On the R&S NetCCU800, open the menu NetCCU > NetCCU Setup > SW Mainte-nance and start the Update mode using the Start function under SW Update Opera-tion.
Chapter 6 Maintenance2098.1190.72 - 6.5 - E-32. Click Rescan in the R&S Software Distributor window. The special components are displayed and you can perform the update in the way de-scribed above.Note None of the remaining functions in the R&S Software Distribution window are relevant forupdates via the R&S NetCCU800; settings that can be accessed using these functionsmust not be changed. Performing software updates for excitersWhen the update procedure described above is performed, the software updates for the ex-citer(s) are also transferred to the R&S NetCCU800. The update for the exciter(s) is starteddirectly via the R&S NetCCU800. 1. Set the R&S NetCCU800 to the Update mode in the way described above. 2. Start the installation software. 3. Select the software package for the exciter.4. Search for instruments in the network and select the exciter for which you want to per-form a software update. 5. Install the update.After the update procedure has been completed, the respective exciter is rebooted auto-matically.
Chapter 6 Maintenance2098.1190.72 - 6.6 - E-3
Broadcasting Division2095.7346.32 - 7.0 - E-1CHAPTER 7TROUBLESHOOTINGPrinted in Germany
Chapter 7 Troubleshooting2098.1190.72 - 7.01 - E-1CONTENTS1 Information ....................................................................................... 1
Chapter 7 Troubleshooting2098.1190.72 - 7.1 - E-11 InformationTroubleshooting information will be provided at a later date.
Broadcasting Division2095.7346.32 - 8.0 - E-1CHAPTER 8SERVICEPrinted in Germany
Chapter 8 Service2098.0188.72 - 8.01 - E-1CONTENTS1 Necessary Tools and Test Equipment ........................................... 12 Overview ........................................................................................... 23 Preparations ..................................................................................... 33.1 Safety ...............................................................................................................33.2 Rack Cabling ...................................................................................................33.3 Removing Front Panel/Rear Panel ................................................................44 Power Distribution ........................................................................... 54.1 Replacing Main Switch ...................................................................................54.1.1 Removing Main Switch .................................................................................54.1.2 Installing Main Switch ...................................................................................64.2 Replacing Motor Protection Switches ..........................................................74.2.1 Removing Motor Protection Switch ..............................................................74.2.2 Installing Motor Protection Switch ................................................................94.3 Replacing Power Distribution Board ..........................................................104.3.1 Removing Power Distribution Board ..........................................................104.3.2 Installing Power Distribution Board ............................................................114.4 Replacing Automatic Line Fuses ................................................................124.4.1 Removing Automatic Line Fuse .................................................................124.4.2 Installing Automatic Line Fuse ...................................................................134.5 Replacing Auxiliary Power Supply Unit .....................................................134.5.1 Removing Auxiliary Power Supply Unit ......................................................134.5.2 Installing the Auxiliary Power Supply Unit ..................................................145 Transmitter Control Unit ............................................................... 155.1 Replacing R&S NetCCU800 .........................................................................155.1.1 Removing R&S NetCCU800 ......................................................................155.1.2 Preparing R&S NetCCU800 for Installation ................................................165.1.3 Installing R&S NetCCU800 ........................................................................175.2 Replacing Rack Controller ...........................................................................175.2.1 Removing Rack Controller .........................................................................175.2.2 Installing Rack Controller ...........................................................................18
Chapter 8 Service2098.0188.72 - 8.02 - E-16 Exciter Components ...................................................................... 196.1 Replacing Exciter .........................................................................................196.1.1 Removing Exciter .......................................................................................196.1.2 Configuring Exciter .....................................................................................206.1.3 Installing Exciter .........................................................................................216.2 Replacing Exciter Switch .............................................................................216.2.1 Removing Exciter Switch ............................................................................216.2.2 Installing Exciter Switch ..............................................................................227 Output Stage Components ........................................................... 237.1 Replacing Amplifiers ....................................................................................237.1.1 Removing Amplifier ....................................................................................237.1.2 Installing Amplifier ......................................................................................247.2 Replacing Absorber .....................................................................................247.2.1 Removing Absorber ....................................................................................247.2.2 Installing Absorber ......................................................................................258 Harmonics Filter ............................................................................ 268.1 Replacing Harmonics Filter .........................................................................268.1.1 Removing Harmonics Filter ........................................................................268.1.2 Installing Harmonics Filter ..........................................................................279 Cooling System .............................................................................. 289.1 Replacing Fans .............................................................................................289.1.1 Removing Fan ............................................................................................289.1.2 Installing Fan ..............................................................................................309.2 Replacing Starting Capacitors ....................................................................309.2.1 Removing Starting Capacitor .....................................................................309.2.2 Installing Starting Capacitor .......................................................................319.3 Replacing Differential Pressure Gages ......................................................319.3.1 Removing Differential Pressure Gage ........................................................329.3.2 Installing Differential Pressure Gage ..........................................................329.4 Replacing Temperature Sensors ................................................................339.4.1 Removing Temperature Sensor .................................................................339.4.2 Installing Temperature Sensor ...................................................................34
Chapter 8 Service2098.0188.72 - 8.1 - E-11 Necessary Tools and Test EquipmentThe specified tools and test equipment include only those items needed for removing sys-tem components and carrying out simple checks on them. Depending on the service work to be performed, you will require the following tools: Screwdriver No. 0Screwdriver No. 1Screwdriver No. 2Phillips screwdriver No. 0Phillips screwdriver No. 1Phillips screwdriver No. 2Torx screwdriver No. 8Torx screwdriver No. 9Torx screwdriver No. 20Hexagonal socket No. 3Hexagonal socket No. 6Open-end wrench No. 7Open-end wrench No. 8Open-end wrench No. 13Multimeter
Chapter 8 Service2098.0188.72 - 8.2 - E-12 OverviewYou can remove and exchange the following units and transmitter components if errors oc-cur: Power distribution– Main switch– Motor protection switches– Automatic line fuses– Power distribution board– Auxiliary power supplyTransmitter control unit– R&S NetCCU800– Rack controllerExciter components–Exciter – Exciter switch (for exciter standby)Output stage components– Amplifiers – AbsorberHarmonics filterCooling system–Fans–Starting capacitors– Differential pressure gages– Temperature sensors
Chapter 8 Service2098.0188.72 - 8.3 - E-13 Preparations3.1 SafetyNote Full information on the subject of safety can be found in the section "Safety".3.2 Rack CablingThe standard components of the transmitter are fully cabled together on delivery. You needto reconnect the separate replacement instruments during service work. Each cable has a yellow collar at each end, inscribed with the cable number (W...) and theintended purpose (module number A..., connector number X...). This makes it easier toconnect the cable concerned to the intended slot or connection point, since the modulesare provided with an engraved or self-adhesive circuit diagram.For easy connection of replacement instruments or devices proceed as follows:1. Find the plug (connector) number from the yellow collar on the cable.2. Find the same number on the instrument you wish to connect (by looking for the femaleconnector or circuit diagram).3. Insert the plug connector into the corresponding female connector.WARNING!All service work should only be carried out by qualified personnel and only on components that have been disconnected from the power supply. Heavy components such as amplifi-ers must always be exchanged using a team of two people.
Chapter 8 Service2098.0188.72 - 8.4 - E-13.3 Removing Front Panel/Rear PanelTo remove the front panel/rear panel proceed as follows:Using a Torx screwdriver No. 20, remove the front or rear panel.Fig. 1 Ground terminal of a front panel/rear panel
Chapter 8 Service2098.0188.72 - 8.5 - E-14 Power Distribution You can replace the following power distribution components:Main switch (power supply terminal)Motor protection switchAutomatic line fusePower distribution boardAuxiliary power supply4.1 Replacing Main Switch4.1.1 Removing Main SwitchTo remove the main switch proceed as follows:1. Using a Torx screwdriver No. 20, remove the front panel of the power distribution.2. Unscrew the rotary knob and the main switch cover.Fig. 2 Unscrewing the rotary knob and cover3. Undo the screws on the switch housing (Phillips screwdriver No. 1) and remove the con-nected cables.WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.6 - E-14. Undo the screws on the terminal rack on the left of the main switch and slide the terminalrack to the left.5. Pull forward the black stop lever on the underside of the main switch.6. Carefully take out the main switch.Fig. 3 Taking out the main switch4.1.2 Installing Main Switch1. Replace the main switch by proceeding in the reverse order.2. Insert the cables into the corresponding openings and fasten them with screws.Note Notice how the cables are labeled and make sure they are in the right sequence, sincetwo of the three phase cables are the same color (black).3. Measure the rotary field with the aid of a rotary field meter.If the rotary field is correct, continue with the next step; if it is wrong, swap two wires fromthe cable and measure the rotary field again.4. Screw the main switch cover and the rotary knob back on.Note When working on the transmitter rack the main switch can be locked in the "OFF" posi-tion (see next figure).
Chapter 8 Service2098.0188.72 - 8.7 - E-1Fig. 4 Main switch locked4.2 Replacing Motor Protection Switches4.2.1 Removing Motor Protection SwitchTo remove the motor protection switch proceed as follows:1. Using a Torx screwdriver No. 20, remove the front panel of the power distribution.2. Pull the blue-green shorting plug forward. If necessary you may use a screwdriver (No. 0) suited to the relatively high amounts offorce that are needed.WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.8 - E-13. Press the motor protection switch sharply downward and pull it forward by the bottomedge. Because there is a spring clip behind the upper edge, you can only release the switchdownward.1) Spring clip4. Use a screwdriver to open the cable clamps and pull out the connected cable (see fig-ure).
Chapter 8 Service2098.0188.72 - 8.9 - E-1Fig. 5 Opening the cable clamp on the motor protection switch4.2.2 Installing Motor Protection SwitchReplace the motor protection switch by proceeding in the reverse order.Note When replacing, feed the shorting plug right in and push the switch into place with someforce.Fig. 6 Installing the motor protection switch
Chapter 8 Service2098.0188.72 - 8.10 - E-11) Room for the shorting plug pins4.3 Replacing Power Distribution Board4.3.1 Removing Power Distribution BoardTo remove the power distribution board proceed as follows:1. Using a Torx screwdriver No. 20, remove the front panel of the power distribution.2. Remove all plugs before removing the power distribution board.3. Unscrew the SUB-D connector on the right of the longitudinal edge (two screws).4. Use a Phillips screwdriver No. 1 to undo eight screws on the automatic line fuses.Fig. 7 Removing the power distribution board1) Screws on the automatic line fuses2) Screws on the SUB-D connector5. Using a Torx screwdriver No. 8 remove seven fixing screws from the power distributionboard.WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.11 - E-1Fig. 8 Removing the power distribution board1) Fixing screws on the power distribution board6. To take out the PCB, first slide it downward.4.3.2 Installing Power Distribution BoardReplace the power distribution board by proceeding in the reverse order.Note When replacing the power distribution board, make sure that it feeds into the right slots.Fig. 9 Installing the power distribution board1) Wrong2) Right3) Pressing with a screwdriver visibly opens the right chamber
Chapter 8 Service2098.0188.72 - 8.12 - E-14.4 Replacing Automatic Line Fuses4.4.1 Removing Automatic Line FuseNote Before removing an automatic line fuse, the power distribution board must be removed (see"Removing the Power Distribution Board").To remove the automatic line fuse proceed as follows:1. Remove the power distribution board.2. From above, grip the back of the automatic line fuse you wish to remove and undo thewhite plastic springs.3. Remove the automatic line fuse.WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.13 - E-1Fig. 10 Automatic line fuse1) Upper plastic spring2) Lower plastic spring4.4.2 Installing Automatic Line FuseReplace the automatic line fuse by proceeding in the reverse order.Note Before putting it back into operation, make sure that all terminals are correctly connected.4.5 Replacing Auxiliary Power Supply Unit4.5.1 Removing Auxiliary Power Supply UnitTo remove the auxiliary power supply proceed as follows:1. Using a Torx screwdriver No. 20, remove the front panel of the power distribution.2. Undo the auxiliary power supply cables (X35, X45) from the power distribution board.Trace the two cables and if necessary cut off the cable ties.3. Undo two Torx screws on the front of the power supply unit.4. Remove the power supply unit.WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.14 - E-1Fig. 11 Removing the power supply unit4.5.2 Installing the Auxiliary Power Supply UnitReplace the power supply unit by proceeding in the reverse order.
Chapter 8 Service2098.0188.72 - 8.15 - E-15 Transmitter Control Unit You can replace the following transmitter control unit components:R&S NetCCU800Rack controller5.1 Replacing R&S NetCCU8005.1.1 Removing R&S NetCCU800Note Removing the R&S NetCCU800 does not affect transmitter operation. 1. Switch off automatic line fuse F1.2. Undo the two captive screws (Torx screwdriver No. 20) at the front brackets of the R&SNetCCU800 and exciter (the screws are next to the handles). 3. Grip the handles and slowly pull the rackmount out of the rack as far as it will go (theguide rails engage and are locked in place). 4. Disconnect the power cable from the rear panel of the R&S NetCCU800.5. Disconnect all cables from the rear panel of the R&S NetCCU800. WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.16 - E-1Fig. 12 Removing R&S NetCCU800 from transmitter rack1) Captive screws at front panel of installed units (here: exciter and R&S NetCCU800)2) Screws securing R&S NetCCU800 to rackmount3) Guide rails4) Support bracket for R&S NetCCU8005) Safety lever for releasing guide rail catch6. Undo the two fastening screws (Torx screwdriver No. 9) from the rackmount on bothsides of the R&S NetCCU800. Note Removal should be performed by two persons. When pulled out by the handles, the R&SNetCCU800 must be supported from below as soon as the support brackets no longersupport it. 7. Pull the R&S NetCCU800 out of the rackmount.5.1.2 Preparing R&S NetCCU800 for InstallationThe replacement R&S NetCCU800 is delivered as a desktop unit and must be prepared forinstallation as follows.Remove the protective rubber caps on the rear feet of the instrument.The replacement unit is as a rule preconfigured with the default configuration. So that thenew R&S NetCCU800 does not adversely affect the operation of the transmitter when it isput into operation in the transmitter rack, it must first be configured specifically for the trans-mitter.
Chapter 8 Service2098.0188.72 - 8.17 - E-1Put the R&S NetCCU800 into local mode and configure the unit specifically for the trans-mitter concerned, as described in the chapter "Commissioning".5.1.3 Installing R&S NetCCU800To install the unit in the transmitter, reverse the procedure used to remove it. 1. Slide the R&S NetCCU800 horizontally into the rackmount on the lowest support brack-ets until the screw holes in the plug-in housing and on the side panels of the R&SNetCCU800 line up. 2. Fasten the R&S NetCCU800 with two screws on each side.3. Connect the cables to the R&S NetCCU800 according to the labeling (see yellow cablecollars).4. Undo the latch on the guide rails. Push down the safety lever on the right while simulta-neously pushing up the safety lever on the left and slide the rackmount into the rack. 5. Retighten the two captive screws on the front panel of the R&S NetCCU800 and exciter. 6. Switch the automatic line fuse F1 on again.5.2 Replacing Rack Controller5.2.1 Removing Rack ControllerNote The rack controller is underneath the R&S NetCCU800.1. Remove the cover by undoing the two screws (Torx screwdriver No. 20).Fig. 13 Removal of rack controller from transmitter rack: removing coverWARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.18 - E-12. Turn the two screws (Torx screwdriver No. 20) on the sides alternately by a few turns. This pushes the rack controller out of the rack and prevents it from tilting.Fig. 14 Removal of rack controller from transmitter rack: undoing fastening screws3. Remove the rack controller from the rack.Fig. 15 Removal of rack controller from transmitter rack: removing rack controller5.2.2 Installing Rack ControllerTo install the rack controller in the transmitter, reverse the procedure used to remove it.
Chapter 8 Service2098.0188.72 - 8.19 - E-16 Exciter Components You can replace the following exciter components:ExciterExciter Switch6.1 Replacing Exciter6.1.1 Removing Exciter1. Switch off automatic line fuse F2 (exciter A) or F3 (exciter B).2. Undo the two captive screws (Torx screwdriver No. 20) from the R&S NetCCU800 andexciter on the front brackets (next to the handles). 3. Using the handles, slowly pull out the rackmount from the rack as far as it will go (theguide rails will engage and lock in place). 4. Disconnect all cables from the rear panel of the exciter. WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.20 - E-1Fig. 16 Removing the exciter from the transmitter rack1) Captive screws at front panel of installed units (here: exciter and R&S NetCCU800)2) Screw-connections of the exciter on the rackmount3) Guide rails4) Safety lever for unlocking guide rail latch5. On both sides of the exciter undo the two fixing screws (Torx screwdriver No. 9) from therackmount. 6. Pull the exciter from the rackmount.6.1.2 Configuring ExciterBefore installing the replacement unit and restarting the transmitter, you should checkwhether the correct transmitter operating mode is set on the exciter. Proceed as follows:1. Connect the exciter via the front-panel Ethernet port to a PC and put the unit into localmode.Note For more information on operating the separate unit, please refer to the Appendix to theexciter manual, section "Remote Operation of the Exciter".2. Start the web browser GUI and log in with "Configuration" rights.3. Call the Exciter *** > Setup > Tx Setup menu, go to Tx Mode and set the transmitteroperating mode to "Med./High Power with NetCCU".4. Call the Exciter *** > Setup > Exciter Setup > Common menu and under Digital Stan-dard set the appropriate digital TV standard to which the R&S NetCCU800 is alreadyconfigured.
Chapter 8 Service2098.0188.72 - 8.21 - E-1Note All the other exciter settings can be checked after installation in the transmitter and ifnecessary adjusted via the R&S NetCCU800.6.1.3 Installing ExciterTo install the unit in the transmitter, reverse the procedure used to remove it. 1. Slide the exciter into the cabinet horizontally on the support brackets until the screwholes on the cabinet and on the side panels of the exciter match. 2. Fasten the exciter with two screws on each side.3. Connect the cables to the exciter according to the labeling (see yellow cable collars).4. Undo the latch on the guide rails. Push down the safety lever on the right while simulta-neously pushing up the safety lever on the left and slide the rackmount into the rack. 5. Retighten the two captive screws on the front panel of the R&S NetCCU800 and exciter. 6. Switch the automatic line fuse F2 (exciter A) or F3 (exciter B) on again.6.2 Replacing Exciter Switch6.2.1 Removing Exciter SwitchIn transmitters with the exciter standby option (2 exciters), the exciter switch is located be-hind the two exciters.Note To allow the exciter switch to be removed easily, you first need to remove the R&S NetCCUand exciter from the rack.1. Undo the two captive screws at the front brackets of the R&S NetCCU800 and exciter(next to the handles). 2. Grip the handles and slowly pull the rackmount out of the rack as far as it will go (theguide rails engage and are locked in place). 3. Disconnect the power cable from the side of the exciter switch. WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.22 - E-1Fig. 17 Removing exciter switch from transmitter rack4. Disconnect all cables from the rear of the exciter switch. 5. Undo the fastening screws on the exciter switch. 6. Pull the exciter switch from the transmitter rack.6.2.2 Installing Exciter SwitchTo install the unit in the transmitter, reverse the procedure used to remove it. 1. Connect the cables to the exciter switch according to the labeling (see yellow cable col-lars).2. Undo the latch on the guide rails. Simultaneously press the safety lever on the right sidedown and on the left side up, and slide the rackmount into the rack. 3. Retighten the captive screws on the front panel of the R&S NetCCU800 and exciter.
Chapter 8 Service2098.0188.72 - 8.23 - E-17 Output Stage Components You can replace the following output stage components:AmplifierAbsorberNote Because of the extremely small probability of failure, replacement of the splitter-combinerunit will not be described.7.1 Replacing AmplifiersWhen replacing an amplifier from the Rohde & Schwarz transmitters, you do not have toremove any of the lines since the connections on the rear panel of the device are connectedto the rack using automatic connectors.7.1.1 Removing Amplifier1. Switch off the amplifier via the AC distributor in the transmitter rack (turn the the appro-priate protective switch to the "OFF" position).Note The other devices in the transmitter rack can remain connected. A transmitter with mul-tiple amplifiers can remain in operation with reduced power during the exchange of theamplifier.2. Undo the four captive screws (Torx screwdriver No. 20) on each side of the front panel.ATTENTION!Prior to being removed, the amplifier must be switched free of all voltages in order to pre-vent any possible damage to the device due to contact consumption.
Chapter 8 Service2098.0188.72 - 8.24 - E-13. Slowly pull the amplifier from the rack using the handles.The automatic connectors should release on the rear panel of the device.4. Put the amplifier down with the bottom of the instrument facing downward.5. If the transmitter is to remain in operation with the remaining amplifiers, close the left andright vents at the vacant amplifier slot.7.1.2 Installing AmplifierTo install the unit in the transmitter, reverse the procedure used to remove it.7.2 Replacing Absorber7.2.1 Removing AbsorberTo remove the absorber proceed as follows:CAUTION!Risk of burns on the heat sink. Let the amplifier cool down for about five minutes with the transmitter cooling switched on before you remove it from the transmitter rack.CAUTION!When you pull it out of the transmitter rack, do not allow the amplifier to fall. Support it from below. The amplifier weighs about 28 kg so we suggest that you use two people to handle it.ATTENTION!To avoid damaging the connectors, do not place the amplifier on its back.WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.25 - E-11. Using a Torx screwdriver No. 20, remove the rear panel of the rack.2. Disconnect the RF connecting cables W1, W2 and W3 to the splitter-combiner unit.3. Using a Torx screwdriver No. 20 remove all six fixing screws.4. Pull the absorber unit from the rackmount air outlet duct.Fig. 18 Removing the absorber7.2.2 Installing AbsorberTo install the unit in the transmitter, reverse the procedure used to remove it.
Chapter 8 Service2098.0188.72 - 8.26 - E-18 Harmonics Filter In this transmitter family the harmonics filter is built into the RF line.8.1 Replacing Harmonics FilterNote The harmonics filter is lacquered in order to reduce the surface temperature, but high tem-peratures are nevertheless to be expected.8.1.1 Removing Harmonics FilterNote The harmonics filter is connected to the RF chain by means of two rigid line brackets. Sothat the inner line of the lower rigid line (into the bandpass) stays fixed in place, the tension-ing clamp of the lower rigid line bracket should be opened first.To remove the harmonics filter proceed as follows:1. Open the tensioning clamp of the lower rigid line bracket on the rigid connection of thecombiner.2. Open the tensioning clamp of the upper rigid line bracket using an open-end wrenchNo. 7 or a Phillips screwdriver No. 2.3. Pull the harmonics filter of the combiner rigid line down and to the right.4. Pull the harmonics filter downward from the upper rigid line bracket.WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.27 - E-1Fig. 19 Removing the harmonics filter8.1.2 Installing Harmonics FilterThe replacement harmonics filter has no rigid line brackets.Remove the rigid line bracket from the old harmonics filter, attach the bracket to the newharmonics filter (top) and screw it firmly in place.To install the unit in the transmitter, reverse the procedure used to remove it.
Chapter 8 Service2098.0188.72 - 8.28 - E-19 Cooling System You can replace the following cooling system components:FanStarting capacitorDifferential pressure gageTemperature sensors9.1 Replacing FansThe transmitter rack contains two fans as standard; one of these can be reached only fromthe front and the other only from the back. However the removal sequence is the same inboth cases.9.1.1 Removing FanNote Prior to removal make sure which of the two fans needs to be replaced.1. Using a Torx screwdriver No. 20, remove the front panel of the power distribution to re-place the front fan, or the rear panel of the transmitter to replace the rear fan.2. Switch off automatic line fuse F6 (rear fan) or F7 (front fan).Note Wait two minutes before starting to remove the fan (to allow for the fan overrun time).3. Undo the four screws on the fan housing and remove the cover.WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.29 - E-1Fig. 20 Undoing the screws from the fan housing4. On the upper side of the fan housing is a retaining device that must be unscrewed usinga Torx screwdriver No. 20.Fig. 21 Unscrewing the retaining device5. Pull the power cable out of the connector and take away the air tube.
Chapter 8 Service2098.0188.72 - 8.30 - E-16. Slide the fan slightly to the side, then pull it toward yourself and out of the fan housing. The fan is easy to remove due to the guide railsFig. 22 Removing a fan9.1.2 Installing FanTo install the unit in the transmitter, reverse the procedure used to remove it.9.2 Replacing Starting Capacitors9.2.1 Removing Starting CapacitorNote Prior to removal make sure which of the two starting capacitors needs to be replaced.WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.31 - E-11. Using a Torx screwdriver No. 20, remove the front panel of the power distribution to re-place the front starting capacitor, or the rear panel of the transmitter to replace the rearstarting capacitor.2. Switch off automatic line fuse F6 (fan 1, rear starting capacitor) or F7 (fan 2, front startingcapacitor).3. Remove the fan connector.4. Undo the nut (M8, wrench width 13 mm) on the face plate of the capacitor.5. Cut off the cable ties to free the cable.Fig. 23 Removing the starting capacitor1) Connector (and socket)2) Cable ties3) Lock washer4) Nut (M8)9.2.2 Installing Starting CapacitorTo install the unit in the transmitter, reverse the procedure used to remove it.Note The lock washer and M8 nut must be fastened together again.9.3 Replacing Differential Pressure GagesWARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.32 - E-19.3.1 Removing Differential Pressure GageNote Prior to removal make sure which of the two differential pressure gages needs to be re-placed.1. Using a Torx screwdriver No. 20, remove the rear panel of the rack.2. Remove the air connector (plastic tube).3. Disconnect the associated cable from the connector on X45 of the power distributionboard. (Pins 1 and 2 for differential pressure gage 1, or pins 3 and 4 for differential pressuregage 2.)4. Cut off the cable ties to free the cable.5. Undo the two screws on the bracket.6. Remove the differential pressure gage.7. Unscrew the round cover and remove the cable (6.3 mm connector).Fig. 24 Removing the differential pressure gage9.3.2 Installing Differential Pressure GageTo install the unit in the transmitter, reverse the procedure used to remove it.Check whether the protective cap for the air nozzle on the left-hand differential pressuregage has already been removed and if not, remove it (see figure).
Chapter 8 Service2098.0188.72 - 8.33 - E-1Fig. 25 Differential pressure gage without protective capNote After installation the differential pressure gage must be set to the switching point of 200 Paagain. 1. Remove the transparent top cover.In the middle is an adjuster with a scale.2. Use a screwdriver to turn the adjuster until the arrow points to the value 200.9.4 Replacing Temperature SensorsThe transmitter rack contains two temperatur sensors which measure the intake and outletair temperatures. They are located on the intake and outlet lines on the rack.9.4.1 Removing Temperature SensorNote Prior to removal make sure which of the two temperature sensors needs to be replaced.1. Using a Torx screwdriver No. 20, remove the rear panel of the rack.2. Unplug the connector of the temperature sensor concerned.WARNING!Always make sure that the power supply is disconnected before commencing any service work on the transmitter rack. This will prevent injury due to electric shock and avoid dam-age to the instruments.
Chapter 8 Service2098.0188.72 - 8.34 - E-1Fig. 26 Removing the temperature sensor3. Using a Phillips screwdriver No. 0, undo the two screws (M3) on the temperature sensorflange.1) Openings for fixing screws (M3)4. Carefully remove the temperature sensor from the aperture in the air duct.9.4.2 Installing Temperature SensorTo install the unit in the transmitter, reverse the procedure used to remove it.
Broadcasting Division2095.7346.72 - 9.0 - D/E-1Interface DescriptionTRANSMITTERPrinted in Germany
Chapter 9 Annex2098.0188.72 - 9.01 - E-1CONTENTS1 Interface Description ....................................................................... 11.1 Front-Panel Interfaces ....................................................................................11.1.1 Q1 – AC Supply Input / Protective Earth ......................................................11.1.2 X57 – Optional Connector Kit ZR800Z1 .......................................................11.1.3 X33 – External Fan (Optional): (Wago Plug-In Terminal) .............................11.1.4 X34 – AC Power Supply for Control Units and Exciters (Single-Phase): (Wago Plug-In Terminal) ..............................................................................21.1.5 X36 – External Absorber Cooling System (Optional): (Wago Plug-In Terminal) ..............................................................................21.1.6 X41 – RF Carrier Loop: (Wago Plug-In Terminal) ........................................31.1.7 X42 – Absorber Monitoring: (Wago Plug-In Terminal) .................................31.1.8 X43 – Cooling Monitoring: (Wago Plug-In Terminal) ....................................31.1.9 X44 – Overcurrent Monitoring for External Fan: (Wago Plug-In Terminal) ..41.2 Interfaces on the Transmitter Top ................................................................41.2.1 X100A – Ethernet A Remote (Standard): (8-Contact Female) .....................41.2.2 X100B – Ethernet B Remote (N+1 Option): (8-Contact Female) .................51.2.3 X232 – RS-232-C: (9-Contact D-Sub Female) .............................................51.2.4 X101A – CAN-Bus Rack Bus A: (9-Contact D-Sub Female) ........................61.2.5 X101B – CAN-Bus Rack Bus A: (9-Contact D-Sub Female) ........................61.2.6 X102A – ANTENNA 1: (N Female, 50 Ohm) ................................................71.2.7 X102B – ANTENNA 2: (N Female, 50 Ohm) ................................................71.2.8 X121A – TS1 Exciter A: (BNC Female, 75 Ohm) .........................................71.2.9 X121B – TS1 Exciter B: (BNC Female, 75 Ohm) .........................................71.2.10 X122A – TS2 Exciter A: (BNC Female, 75 Ohm) .........................................81.2.11 X122B – TS2 Exciter B: (BNC Female, 75 Ohm) .........................................81.2.12 X123A – TS3 Exciter A: (BNC Female, 75 Ohm) .........................................81.2.13 X123B – TS3 Exciter B: (BNC Female, 75 Ohm) .........................................81.2.14 X124A – TS4 Exciter A: (BNC Female, 75 Ohm) .........................................91.2.15 X124B – TS4 Exciter B: (BNC Female, 75 Ohm) .........................................91.2.16 X131A – TS1/2 IN Monitoring Exciter A: (BNC Female) ..............................91.2.17 X131B – TS1/2 IN Monitoring Exciter B: (BNC Female) ..............................91.2.18 X132A – TS3/4 IN Monitoring Exciter A: (BNC Female) ............................101.2.19 X132B – TS3/4 IN Monitoring Exciter B: (BNC Female) ............................101.2.20 X141A – 1PPS Exciter A: (BNC Female, 50 Ohm) ....................................10
Chapter 9 Annex2098.0188.72 - 9.02 - E-11.2.21 X141B – 1PPS Exciter B: (BNC Female, 50 Ohm) ....................................101.2.22 X142A – 1PPS Monitoring Exciter A: (BNC Female, 50 Ohm) ..................111.2.23 X142B – 1PPS Monitoring Exciter B: (BNC Female, 50 Ohm) ..................111.2.24 X143A – 10 MHz REF.INPUT Exciter A: (BNC Female, 50 Ohm) .............111.2.25 X143B – 10 MHz REF.INPUT Exciter B: (BNC Female, 50 Ohm) .............111.2.26 RF Transmitter Output (EIA 1 5/8" Flange 50 Ohm ....................................121.3 Monitoring Outputs on Front Panel of R&S SV800 Exciter ......................121.3.1 X65A – 10 MHz Test Output for Exciter A: (SMA Female, 50 Ohm) ..........121.3.2 X65B – 10 MHz Test Output for Exciter B: (SMA Female, 50 Ohm) ..........121.3.3 X61A – RF Test Output for Exciter A: (SMA Female, 50 Ohm) .................121.3.4 X61B – RF Test Output for Exciter B: (SMA Female, 50 Ohm) .................13
Chapter 9 Annex2098.0188.72 - 9.1 - E-11 Interface Description1.1 Front-Panel Interfaces1.1.1 Q1 – AC Supply Input / Protective Earth1.1.2 X57 – Optional Connector Kit ZR800Z11.1.3 X33 – External Fan (Optional): (Wago Plug-In Terminal)Signal name Direction Value range Contact RemarkPHASE L1 Input 400 V ±15% Q1.T1 Three-phase current input L1PHASE L2 Input 400 V ±15% Q1.T2 Three-phase current input L2PHASE L3 Input 400 V ±15% Q1.T3 Three-phase current input L1NEUTRAL N Input 0 V Q1.N Neutral-conductor input NPROTECTION EARTH PEInput 0 V X.PE PE terminalPROTECTION EARTH PEInput 0 V PE pin PE stationSignal name Direction Value range Contact RemarkPHASE L1 Input 230 V X57.L1 Separate circuitNEUTRAL N Input 0 V X57.NPROTECTION EARTH PEInput 0 V X57.PESignal name Direction Value range Contact RemarkPHASE L1 Input 230 V X33.1 Line protection F8 [3A]NEUTRAL N Input 0 V X33.2
Chapter 9 Annex2098.0188.72 - 9.2 - E-1External fan for dummy antenna (optional): (Wago plug-in terminal)1.1.4 X34 – AC Power Supply for Control Units and Exciters (Single-Phase): (Wago Plug-In Terminal)1.1.5 X36 – External Absorber Cooling System (Optional): (Wago Plug-In Terminal)PROTECTION EARTH PEInput 0 V X33.3Signal name Direction Value range Contact RemarkPHASE L1 Input 230 V X33.4 Line protection F8 [3A]NEUTRAL N Input 0 V X33.5PROTECTION EARTH PEInput 0 V X33.6Signal name Direction Value range Contact RemarksPHASE L1 Output 230 V X34.1 Line fuse F1 [3A] R&S NetCCU800 connectionPHASE L1 Output 230 V X34.2 Line fuse F2 [3A] Sx800 A connectionPHASE L1 Output 230 V X34.3 Line fuse F3 [3A] Sx800 B connectionPHASE L1 Output 230 V X34.4 Line fuse F4 [3A] Add-on equipment connec-tionNEUTRAL N Input 0 V X34.5PROTECTION EARTH PEInput 0 V X34.6Signal name Direction Value range Contact RemarksPHASE L3 Output 230 V X36.1 Line fuse F8 [3A]Signal name Direction Value range Contact Remark
Chapter 9 Annex2098.0188.72 - 9.3 - E-11.1.6 X41 – RF Carrier Loop: (Wago Plug-In Terminal)1.1.7 X42 – Absorber Monitoring: (Wago Plug-In Terminal)1.1.8 X43 – Cooling Monitoring: (Wago Plug-In Terminal)NEUTRAL N Input 0 V X36.2PROTECTION EARTH PEInput 0 V X36.3Signal name Direction Value range Contact RemarkMAIN TX LOOP Input -12 V ±2 V X41.1 -12 V floatingLOOP COM (+) Output +12 V ±2 V X41.2 +12 V floatingRESERVE TX LOOPInput -12 V ±2 V X41.3 -12 V floatingLOOP COM (+) Output +12 V ±2 V X41.4 +12 V floatingSignal name Direction Value range Contact RemarkFAULT SYSTEM ABSORBERInput TTL X42.1 Jumper to 0 VREF RACK SIGNALSOutput 0 V X42.2 Reference 0 VFAULT RACK ABSORBERInput TTL X42.3 Jumper to 0 VREF RACK SIGNALSOutput 0 V X42.4 Reference 0 VSignal name Direction Value range Contact RemarksFAULT COOLING 2Input TTL X43.1 Jumper against 0 VREF RACK SIGNALSInput 0 V X43.2 Reference 0 VSignal name Direction Value range Contact Remarks
Chapter 9 Annex2098.0188.72 - 9.4 - E-11.1.9 X44 – Overcurrent Monitoring for External Fan: (Wago Plug-In Terminal)1.2 Interfaces on the Transmitter Top1.2.1 X100A – Ethernet A Remote (Standard): (8-Contact Female)FAULT COOLING 1Input TTL X43.3 Jumper against 0 VREF RACK SIGNALSInput 0 V X43.4 Reference 0 VWARNING COOLINGInput TTL X43.5 Jumper against 0 VREF RACK SIGNALSInput 0 V X43.6 Reference 0 VSignal name Direction Value range Contact RemarkFAULT EXT: COOLINGInput TTL X44.1 Jumper to 0 VREF RACK SIGNALSOutput 0 V X44.4 Reference 0 VSignal name Direction Value range Contact RemarkTX+ Output Ethernet X100A.1 Transmitting lineTX- Output Ethernet X100A.2 Transmitting lineRX+ Input Ethernet X100A.3 Receiving lineBidirect. 75  termina-tionX100A.4Bidirect. 75  termina-tionX100A.5RX- Input Ethernet X100A.6 Receiving lineBidirect. 75  termina-tionX100A.7Signal name Direction Value range Contact Remarks
Chapter 9 Annex2098.0188.72 - 9.5 - E-11.2.2 X100B – Ethernet B Remote (N+1 Option): (8-Contact Female)1.2.3 X232 – RS-232-C: (9-Contact D-Sub Female)Bidirect. 75  termina-tionX100A.8Signal name Direction Value range Contact RemarkTX+ Output Ethernet X100B.1 Transmitting lineTX- Output Ethernet X100B.2 Transmitting lineRX+ Input Ethernet X100B.3 Receiving lineBidirect. 75  termina-tionX100B.4Bidirect. 75  termina-tionX100B.5RX- Input Ethernet X100B.6 Receiving lineBidirect. 75  termina-tionX100B.7Bidirect. 75  termina-tionX100B.8Signal name Direction Value range Contact Remarkn.c. X232.1 Transmitting lineRS232_TX Output RS-232 X232.2 Transmitting lineRS232_RX Input RS-232 X232.3 Receiving linen.c. X232.4GND Bidirect. X232.5n.c. X232.6n.c. X232.7n.c. X232.8Signal name Direction Value range Contact Remark
Chapter 9 Annex2098.0188.72 - 9.6 - E-11.2.4 X101A – CAN-Bus Rack Bus A: (9-Contact D-Sub Female)1.2.5 X101B – CAN-Bus Rack Bus A: (9-Contact D-Sub Female)Signal name Direction Value range Contact Remark12V_RED Bidirect. 12 V ±1 V X101A.1 Redundant 12 V supplyRC_A_CAN_L Bidirect. CAN-Level X101A.2 CAN bus signalCAN_GND Bidirect. 0 V X101A.3 CAN GND12V_RED Bidirect. 12 V ±1 V X101A.4 Redundant 12 V supplyCAN_SHLD Bidirect. GND X101A.5 ShieldGND Bidirect. GND X101A.6 GNDRC_A_CAN_H Bidirect. CAN+Level X101A.7 CAN bus signal12V_ASI Bidirect. 12 V ±1.5 V X101A.8CAN_V+ Bidirect. 12 V ±1 V X101A.9Signal name Direction Value range Contact Remark12V_RED Bidirect. 12 V ±1 V X101B.1 Redundant 12 V supplyRC_A_CAN_L Bidirect. CAN-Level X101B.2 CAN bus signalCAN_GND Bidirect. 0 V X101B.3 CAN GND12V_RED Bidirect. 12 V ±1 V X101B.4 Redundant 12 V supplyCAN_SHLD Bidirect. GND X101B.5 ShieldGND Bidirect. GND X101B.6 GNDRC_A_CAN_H Bidirect. CAN+Level X101B.7 CAN bus signal12V_ASI Bidirect. 12 V ±1.5 V X101B.8CAN_V+ Bidirect. 12 V ±1 V X101B.9
Chapter 9 Annex2098.0188.72 - 9.7 - E-11.2.6 X102A – ANTENNA 1: (N Female, 50 Ohm)1.2.7 X102B – ANTENNA 2: (N Female, 50 Ohm)1.2.8 X121A – TS1 Exciter A: (BNC Female, 75 Ohm)1.2.9 X121B – TS1 Exciter B: (BNC Female, 75 Ohm)Signal name Direction Value range Contact RemarksANTENNA 1 Input > 80 dBV X102A.1 For DVB-T only Tx level depending on appli-cationGND Bidirect. 0 V X102A.2Signal name Direction Value range Contact RemarksANTENNA 2 Input > 80 dBV X102B.1 For DVB-T only Tx level depending on appli-cationGND Bidirect. 0 V X102B.2Signal name Direction Value range Contact RemarkTS1 Input ASI/SMPTE310M X121A.1 TS1 Exciter AGND Bidirect. X121A.2 GND/shieldSignal name Direction Value range Contact RemarkTS1 Input ASI/SMPTE310M X121B.1 TS1 Exciter BGND Bidirect. X121B.2 GND/shield
Chapter 9 Annex2098.0188.72 - 9.8 - E-11.2.10 X122A – TS2 Exciter A: (BNC Female, 75 Ohm)1.2.11 X122B – TS2 Exciter B: (BNC Female, 75 Ohm)1.2.12 X123A – TS3 Exciter A: (BNC Female, 75 Ohm)1.2.13 X123B – TS3 Exciter B: (BNC Female, 75 Ohm)Signal name Direction Value range Contact RemarkTS2 Input ASI/SMPTE310M X122A.1 TS2 Exciter AGND Bidirect. X122A.2 GND/shieldSignal name Direction Value range Contact RemarkTS2 Input ASI/SMPTE310M X122B.1 TS2 Exciter BGND Bidirect. X122B.2 GND/shieldSignal name Direction Value range Contact RemarksTS3 Input ASI X123A.1 Only for DVB-T with hierar-chical coding TS3 Exciter AGND Bidirect. X123A.2 GND/shieldSignal name Direction Value range Contact RemarksTS3 Input ASI X123B.1 Only for DVB-T with hierar-chical coding TS3 Exciter BGND Bidirect. X123B.2 GND/shield
Chapter 9 Annex2098.0188.72 - 9.9 - E-11.2.14 X124A – TS4 Exciter A: (BNC Female, 75 Ohm)1.2.15 X124B – TS4 Exciter B: (BNC Female, 75 Ohm)1.2.16 X131A – TS1/2 IN Monitoring Exciter A: (BNC Female)1.2.17 X131B – TS1/2 IN Monitoring Exciter B: (BNC Female)Signal name Direction Value range Contact RemarksTS4 Input ASI X124A.1 Only for DVB-T with hierar-chical coding TS4 Exciter AGND Bidirect. X124A.2 GND/shieldSignal name Direction Value range Contact RemarksTS4 Input ASI X124B.1 Only for DVB-T with hierar-chical coding TS4 Exciter BGND Bidirect. X124B.2 GND/shieldSignal name Direction Value range Contact RemarkTS1/2 IN MonitoringOutput ASI/SMPTE310M X131A.1 TS1/2 Monitoring Exciter AGND Bidirect. X131A.2 GND/shieldSignal name Direction Value range Contact RemarkTS1/2 IN MonitoringOutput ASI/SMPTE310M X131B.1 TS1/2 Monitoring Exciter BGND Bidirect. X131B.2 GND/shield
Chapter 9 Annex2098.0188.72 - 9.10 - E-11.2.18 X132A – TS3/4 IN Monitoring Exciter A: (BNC Female)1.2.19 X132B – TS3/4 IN Monitoring Exciter B: (BNC Female)1.2.20 X141A – 1PPS Exciter A: (BNC Female, 50 Ohm)1.2.21 X141B – 1PPS Exciter B: (BNC Female, 50 Ohm)Signal name Direction Value range Contact RemarksTS3/4 IN MonitoringOutput ASI X132A.1 Only for DVB-T with hierar-chical coding TS3/4 Monitoring Exciter AGND Bidirect. X132A.2 GND/shieldSignal name Direction Value range Contact RemarksTS3/4 IN MonitoringOutput ASI X132B.1 Only for DVB-T with hierar-chical coding TS3/4 monitoring Exciter BGND Bidirect. X132B.2 GND/shieldSignal name Direction Value range Contact Remarks1PPS_EXTERN Input TTL level (pos.edge)X141A.1 Second pulse from external GPS receiver (exciter A)GND Bidirect. X141A.2 GND/shieldSignal name Direction Value range Contact Remarks1PPS_EXTERN Input TTL level (pos.edge)X141B.1 Second pulse from external GPS receiver (exciter B)GND Bidirect. X141B.2 GND/shield
Chapter 9 Annex2098.0188.72 - 9.11 - E-11.2.22 X142A – 1PPS Monitoring Exciter A: (BNC Female, 50 Ohm)1.2.23 X142B – 1PPS Monitoring Exciter B: (BNC Female, 50 Ohm)1.2.24 X143A – 10 MHz REF.INPUT Exciter A: (BNC Female, 50 Ohm)1.2.25 X143B – 10 MHz REF.INPUT Exciter B: (BNC Female, 50 Ohm)Signal name Direction Value range Contact Remarks1PPS Monitor-ingOutput TTL level (pos.edge)X142A.1 Monitor output of internally used 1PPS (exciter A)GND Bidirect. X142A.2 GND/shieldSignal name Direction Value range Contact Remarks1PPS Monitor-ingOutput TTL level (pos.edge)X142B.1 Monitor output of internally used 1PPS (exciter B)GND Bidirect. X142B.2 GND/shieldSignal name Direction Value range Contact Remark10 MHz REF INPUTInput -5.0 dB to 20 dBm or TTLX143A.1 10 MHz reference for exciter AGND Bidirect. X142A.2 GND/shieldSignal name Direction Value range Contact Remark10 MHz REF INPUTInput -5.0 dB to 20 dBm or TTLX143B.1 10 MHz reference for exciter BGND Bidirect. X142B.2 GND/shield
Chapter 9 Annex2098.0188.72 - 9.12 - E-11.2.26 RF Transmitter Output (EIA 1 5/8" Flange 50 Ohm1.3 Monitoring Outputs on Front Panel of R&S SV800 Exciter1.3.1 X65A – 10 MHz Test Output for Exciter A: (SMA Female, 50 Ohm)1.3.2 X65B – 10 MHz Test Output for Exciter B: (SMA Female, 50 Ohm)1.3.3 X61A – RF Test Output for Exciter A: (SMA Female, 50 Ohm)Signal name Direction Value range Contact RemarkRF transmitter outputOutput PmaxAVG = 1.8 kW RF RF transmitter output, fully equipped with 4 amplifiersGND Bidirect. RF GND/shieldSignal name Direction Value range Contact Remarks10MHz_REF_OUTOutput 0 dBm (+2 dB to -1 dB)X65A.1 10MHz reference monitor-ing for exciter AGND Bidirect. X65A.2 GND/shieldSignal name Direction Value range Contact Remarks10MHz_REF_OUTOutput 0 dBm (+2 dB to -1 dB)X65B.1 10MHz reference monitor-ing for exciter BGND Bidirect. X65B.2 GND/shieldSignal name Direction Value range Contact RemarksRF_MONOUT Output -7dBm ±2dB X61A.1 RF OUT monitoring for exciter A
Chapter 9 Annex2098.0188.72 - 9.13 - E-11.3.4 X61B – RF Test Output for Exciter B: (SMA Female, 50 Ohm)GND Bidirect. X61A.2 GND/shieldSignal name Direction Value range Contact RemarksRF_MONOUT Output -7dBm ±2dB X61B.1 RF OUT monitoring for exciter BGND Bidirect. X61B.2 GND/shieldSignal name Direction Value range Contact Remarks
Chapter 9 Annex2098.0188.72 - 9.14 - E-1
Broadcasting Division2098.7346.72 - 10.0 - E-1DATA SHEETSPrinted in Germany
Broadcasting Division2098.0188.72 -01 - 2.1 -System ManualVolume 2R&S®NV830xDTV Transmitter ATSCTransmitter Series Nx8000Only skilled personnel may perform the operations of the described instrument thatare necessary for installing and putting it into operation as well as maintaining, trou-bleshooting and servicing it.Printed in Germany
System ManualTransmitter Series Nx8000Edition: August 2009Version: E 01.002098.0188.72 -01- 2.2 -© 2009 Rohde&Schwarz GmbH & Co. KG 81671 Munich, GermanyThis document may be duplicated or otherwise used or its contents made known to third parties only withpermission of the originator or other authorized persons.Infringements constitute an offence and are subject to claim for damages (UrhG, UWG, BGB).All rights reserved for patenting or utility model registration.The R&S logo, Rohde & Schwarz and R&S are registered trademarks of Rohde & Schwarz GmbH & Co.KG and their subsidiaries.ROHDE & SCHWARZ GmbH & Co.KGD-81671 München - Mühldorfstraße 15Telefon: (089) 4129-0 ^ Int. +49894129-0Telefax: (089) 4129-12164Internet: www.rohde-schwarz.comPrinted in Federal Republic of Germany ^ Subject to change ^ Data without tolerances: typical values
2098.0188.72 - 2.3 - E-1NV830XE/V CONTENTSDRAWINGS AND DIAGRAMS NV8301 1DRAWINGS AND DIAGRAMS NV8302 2DRAWINGS AND DIAGRAMS NV8303 3DRAWINGS AND DIAGRAMS NV8304 4SPARE PARTS LISTS 56789
Broadcasting Division2098.0188.72 - 1 - E-1Drawings and DiagramsNV8301E/V2098.0307.01Printed in Germany
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_el.KennzPart Benennung / HinweiseDesignation SachnummerStock No. HerstellerManufacturer BestellbezeichnungDesignation enthalten incontained ina Benennung/DesignationNV8301X DTV-SENDERNV8301X DTV XMTRSprach./Langde en Ä.I. / C.I01.00 Blatt/Sheet1 of 1Dokument Nr. / Document No.2098.0307.01 SANV8301X Datum/Date 2008-01-17 Abt. /Dept. 7TSK Name /Name RoACHTUNG EGB /ATTENTION ESD*VARIANTENERKLAERUNG*EXPLANATION OF MODELSVAR04=NV8301E DTV-SENDER MIT EINZEL-VORSTUFE PROGNOSESENDERMOD04=NV8301E DTV-TRANSMITTER WITH SINGLE EXCITERVAR24=NV8301V DTV-SENDER MIT VORSTUFE-RESERVE OHNE ADE PROGNOSESENDERMOD24=NV8301V DTV TRANSMITTER WITH DUAL DRIVE WITHOUT ADEVAR50=NV8301X DTV-SENDER +++GRUNDSENDER+++MOD50=NV8301X DTV-TRANSMITTER ++BASIC TRANSMITTER++A1 GG VH8300A1 UHF-VERSTAER. 3-Phasig2095.6004.02 2098.0307.01VH8300A1 UHF-AMPLIFIERVAR 04 24A20 GS ZR800T1 EINBAUS. SX800 2099.1007.03 2098.0307.01ZR800T1 INSTAL. KITVAR 04 24DTV - AusfuehrungA21 GS ZR800C1 LEISTUNGSSATZ 2098.5009.41 2098.0307.01ZR800C1 POWER KITVAR 04 24Leistungssatz fuer 1 VerstaerkerA23 GS ZR800V1 VORST.SA SX800 2099.1507.04 2098.0307.01ZR800V1 EXC.INST. KITVAR 24Vorstufensatz - DTV ohne ADEA200 GG NETCCU 800 CONTROL UNIT 2095.8007.02 2098.0307.01NETCCU 800 CONTROL UNITVAR 04 24A100A GG SX800 TV EXCITER DTV UND ADE INT RF2095.1502.71 2098.0307.01SX800 TV EXCITERVAR 04 24A100B GG SX800 TV EXCITER DTV UND ADE INT RF2095.1502.71 2098.0307.01SX800 TV EXCITERVAR 24
DTV-TA NSMITTER BD.IV/VRS7TSK2098.0307 V12098.0307.01BenennungZeichn.-Nr.Änderungs- MitteilungTagNameBearb.Gepr.NormÄnd.Zust.TagNamezu Gerätreg. i. V.erste Z.Blatt-Nr.v. Bl.ROHDE & SCHWARZRO0000.0000.00D1NV8301x DTV-Sender Bd.IV/V01.08NV8301xS\DESI-DAT\NV8300\NV8301x01.00 01.08 RO#) OPTION Variantenerklärung siehe SchaltteillisteValid for model see parts listTiefe: 800Depth: 800A200A1A100AA100B#)ROHDE & SCHWARZ2000600
Broadcasting Division2098.0188.72 - 2 - E-1Drawings and DiagramsNV8302E/V2098.0059.01Printed in Germany
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_el.KennzPart Benennung / HinweiseDesignation SachnummerStock No. HerstellerManufacturer BestellbezeichnungDesignation enthalten incontained ina Benennung/DesignationNV8302X DTV-SENDERNV8302X DTV XMTRSprach./Langde en Ä.I. / C.I01.00 Blatt/Sheet1 of 1Dokument Nr. / Document No.2098.0059.01 SANV8302X Datum/Date 2008-01-17 Abt. /Dept. 7TSK Name /Name RoACHTUNG EGB /ATTENTION ESD*VARIANTENERKLAERUNG*EXPLANATION OF MODELSVAR04=NV8302E DTV-SENDER MIT EINZEL-VORSTUFE PROGNOSESENDERMOD04=NV8302E DTV-TRANSMITTER WITH SINGLE EXCITERVAR24=NV8302V DTV-SENDER MIT VORSTUFE-RESERVE OHNE ADE PROGNOSESENDERMOD24=NV8302V DTV TRANSMITTER WITH DUAL DRIVE WITHOUT ADEVAR50=NV8302X DTV-SENDER +++GRUNDSENDER+++MOD50=NV8302X DTV-TRANSMITTER ++BASIC TRANSMITTER++A1 - A2 GG VH8300A1 UHF-VERSTAER. 3-Phasig2095.6004.02 2098.0059.01VH8300A1 UHF-AMPLIFIERVAR 04 24A20 GS ZR800T1 EINBAUS. SX800 2099.1007.03 2098.0059.01ZR800T1 INSTAL. KITVAR 04 24DTV - AusfuehrungA21 GS ZR800C1 LEISTUNGSSATZ 2098.5009.42 2098.0059.01ZR800C1 POWER KITVAR 04 24Leistungssatz fuer 2 VerstaerkerA23 GS ZR800V1 VORST.SA SX800 2099.1507.04 2098.0059.01ZR800V1 EXC.INST. KITVAR 24Vorstufensatz - DTV ohne ADEA200 GG NETCCU 800 CONTROL UNIT 2095.8007.02 2098.0059.01NETCCU 800 CONTROL UNITVAR 04 24A100A GG SX800 TV EXCITER DTV UND ADE INT RF2095.1502.71 2098.0059.01SX800 TV EXCITERVAR 04 24A100B GG SX800 TV EXCITER DTV UND ADE INT RF2095.1502.71 2098.0059.01SX800 TV EXCITERVAR 24
DTV-TA NSMITTER BD.IV/VRS7TSK2098.0059 V12098.0059.01BenennungZeichn.-Nr.Änderungs- MitteilungTagNameBearb.Gepr.NormÄnd.Zust.TagNamezu Gerätreg. i. V.erste Z.Blatt-Nr.v. Bl.ROHDE & SCHWARZRO0000.0000.00D1NV8302x DTV-Sender Bd.IV/V01.08NV8302xS\DESI-DAT\NV8300\NV8302x01.00 01.08 RO#) OPTION Variantenerklärung siehe SchaltteillisteValid for model see parts listTiefe: 800Depth: 800A200A1A100AA100B#)A2ROHDE & SCHWARZ2000600
Broadcasting Division2098.0188.72 - 3 - E-1Drawings and DiagramsNV8303E/V2098.0107.01Printed in Germany
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_el.KennzPart Benennung / HinweiseDesignation SachnummerStock No. HerstellerManufacturer BestellbezeichnungDesignation enthalten incontained ina Benennung/DesignationNV8303X DTV-SENDERNV8303X DTV XMTRSprach./Langde en Ä.I. / C.I01.00 Blatt/Sheet1 of 1Dokument Nr. / Document No.2098.0107.01 SANV8303X Datum/Date 2008-01-17 Abt. /Dept. 7TSK Name /Name RoACHTUNG EGB /ATTENTION ESD*VARIANTENERKLAERUNG*EXPLANATION OF MODELSVAR04=NV8303E DTV-SENDER MIT EINZEL-VORSTUFE PROGNOSESENDERMOD04=NV8303E DTV-TRANSMITTER WITH SINGLE EXCITERVAR24=NV8303V DTV-SENDER MIT VORSTUFE-RESERVE OHNE ADE PROGNOSESENDERMOD24=NV8303V DTV TRANSMITTER WITH DUAL DRIVE WITHOUT ADEVAR50=NV8303X DTV-SENDER +++GRUNDSENDER+++MOD50=NV8303X DTV-TRANSMITTER ++BASIC TRANSMITTER++A1 - A3 GG VH8300A1 UHF-VERSTAER. 3-Phasig2095.6004.02 2098.0107.01VH8300A1 UHF-AMPLIFIERVAR 04 24A20 GS ZR800T1 EINBAUS. SX800 2099.1007.03 2098.0107.01ZR800T1 INSTAL. KITVAR 04 24DTV - AusfuehrungA21 GS ZR800C1 LEISTUNGSSATZ 2098.5009.43 2098.0107.01ZR800C1 POWER KITVAR 04 24Leistungssatz fuer 3 VerstaerkernA23 GS ZR800V1 VORST.SA SX800 2099.1507.04 2098.0107.01ZR800V1 EXC.INST. KITVAR 24Vorstufensatz - DTV ohne ADEA200 GG NETCCU 800 CONTROL UNIT 2095.8007.02 2098.0107.01NETCCU 800 CONTROL UNITVAR 04 24A100A GG SX800 TV EXCITER DTV UND ADE INT RF2095.1502.71 2098.0107.01SX800 TV EXCITERVAR 04 24A100B GG SX800 TV EXCITER DTV UND ADE INT RF2095.1502.71 2098.0107.01SX800 TV EXCITERVAR 24
DTV-TA NSMITTER BD.IV/VRS7TSK2098.0107 V12098.0107.01BenennungZeichn.-Nr.Änderungs- MitteilungTagNameBearb.Gepr.NormÄnd.Zust.TagNamezu Gerätreg. i. V.erste Z.Blatt-Nr.v. Bl.ROHDE & SCHWARZRO0000.0000.00D1NV8303x DTV-Sender Bd.IV/V01.08NV8303xS\DESI-DAT\NV8300\NV8303x01.00 01.08 RO#) OPTION Variantenerklärung siehe SchaltteillisteValid for model see parts listTiefe: 800Depth: 800A200A1A100AA100B#)A2A3ROHDE & SCHWARZ2000600
Broadcasting Division2098.0188.72 - 4 - E-1Drawings and DiagramsNV8304E/V2098.0159.01Printed in Germany
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_el.KennzPart Benennung / HinweiseDesignation SachnummerStock No. HerstellerManufacturer BestellbezeichnungDesignation enthalten incontained ina Benennung/DesignationNV8304X DTV-SENDERNV8304X DTV XMTRSprach./Langde en Ä.I. / C.I01.00 Blatt/Sheet1 of 1Dokument Nr. / Document No.2098.0159.01 SANV8304X Datum/Date 2008-01-17 Abt. /Dept. 7TSK Name /Name RoACHTUNG EGB /ATTENTION ESD*VARIANTENERKLAERUNG*EXPLANATION OF MODELSVAR04=NV8304E DTV-SENDER MIT EINZEL-VORSTUFE PROGNOSESENDERMOD04=NV8304E DTV-TRANSMITTER WITH SINGLE EXCITERVAR24=NV8304V DTV-SENDER MIT VORSTUFE-RESERVE OHNE ADE PROGNOSESENDERMOD24=NV8304V DTV TRANSMITTER WITH DUAL DRIVE WITHOUT ADEVAR50=NV8304X DTV-SENDER +++GRUNDSENDER+++MOD50=NV8304X DTV-TRANSMITTER ++BASIC TRANSMITTER++A1 - A4 GG VH8300A1 UHF-VERSTAER. 3-Phasig2095.6004.02 2098.0159.01VH8300A1 UHF-AMPLIFIERVAR 04 24A20 GS ZR800T1 EINBAUS. SX800 2099.1007.03 2098.0159.01ZR800T1 INSTAL. KITVAR 04 24DTV - AusfuehrungA21 GS ZR800C1 LEISTUNGSSATZ 2098.5009.44 2098.0159.01ZR800C1 POWER KITVAR 04 24Leistungssatz fuer 4 VerstaerkernA23 GS ZR800V1 VORST.SA SX800 2099.1507.04 2098.0159.01ZR800V1 EXC.INST. KITVAR 24Vorstufensatz - DTV ohne ADEA200 GG NETCCU 800 CONTROL UNIT 2095.8007.02 2098.0159.01NETCCU 800 CONTROL UNITVAR 04 24A100A GG SX800 TV EXCITER DTV UND ADE INT RF2095.1502.71 2098.0159.01SX800 TV EXCITERVAR 04 24A100B GG SX800 TV EXCITER DTV UND ADE INT RF2095.1502.71 2098.0159.01SX800 TV EXCITERVAR 24
DTV-TA NSMITTER BD.IV/VRS7TSK2098.0159 V12098.0159.01BenennungZeichn.-Nr.Änderungs- MitteilungTagNameBearb.Gepr.NormÄnd.Zust.TagNamezu Gerätreg. i. V.erste Z.Blatt-Nr.v. Bl.ROHDE & SCHWARZRO0000.0000.00D1NV8304x DTV-Sender Bd.IV/V01.08NV8304xS\DESI-DAT\NV8300\NV8304x01.00 01.08 RO#) OPTION Variantenerklärung siehe SchaltteillisteValid for model see parts listTiefe: 800Depth: 800A200A1A100AA100B#)A2A3A4ROHDE & SCHWARZ2000600
Broadcasting Division2098.0188.72 - 5 - E-1Spare Parts ListsTRANSMITTERSPrinted in Germany
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLISTE ZR800C1 LEISTUNGSS.SPARE PART LIST FOR 2098.5009.01Sprach./Langde en Ä.I. / C.I04.00 Blatt/Sheet1 of 10Dokument Nr. / Document No.2098.5067.01 STZR800C1 Datum/Date 2009-07-09 Abt. /Dept. 7TSK Name /Name RO ACHTUNG EGB/ATTENTION ESD *VARIANTENERKLAERUNG *EXPLANATION OF MODELS VAR11=MIT 1 VERSTAERKER BAND III MOD11=WITH 1 AMPLIFIER BAND III VAR12=MIT 2 VERSTAERKER BAND III MOD12=WITH 2 AMPLIFIER BAND III VAR13=MIT 3 VERSTAERKER BAND III MOD13=WITH 3 AMPLIFIER BAND III VAR14=MIT 4 VERSTAERKER BAND III MOD14=WITH 4 AMPLIFIER BAND III VAR15=MIT 5 VERSTAERKER BAND III MOD15=WITH 5 AMPLIFIER BAND III VAR16=MIT 6 VERSTAERKER BAND III MOD16=WITH 6 AMPLIFIER BAND III VAR21=MIT 1 VERSTAERKER BAND IV/V MOD21=WITH 1 AMPLIFIER BAND IV/V VAR22=MIT 2 VERSTAERKER BAND IV/V MOD22=WITH 2 AMPLIFIER BAND IV/V VAR23=MIT 3 VERSTAERKER BAND IV/V MOD23=WITH 3 AMPLIFIER BAND IV/V VAR24=MIT 4 VERSTAERKER BAND IV/V MOD24=WITH 4 AMPLIFIER BAND IV/V VAR25=MIT 5 VERSTAERKER BAND IV/V MOD25=WITH 5 AMPLIFIER BAND IV/V VAR26=MIT 6 VERSTAERKER BAND IV/V MOD26=WITH 6 AMPLIFIER BAND IV/V VAR31=FUER NX8300 MIT 1 VERSTAERKER BAND III MOD31=FOR NX8300 WITH 1 AMPLIFIER BAND III VAR32=FUER NX8300 MIT 2 VERSTAERKER BAND III MOD32=FOR NX8300 WITH 2 AMPLIFIER BAND III VAR33=FUER NX8300 MIT 3 VERSTAERKER BAND III MOD33=FOR NX8300 WITH 3 AMPLIFIER BAND III VAR34=FUER NX8300 MIT 4 VERSTAERKER BAND III MOD34=FOR NX8300 WITH 4 AMPLIFIER BAND III VAR35=FUER NX8300 MIT 5 VERSTAERKER BAND III MOD35=FOR NX8300 WITH 5 AMPLIFIER BAND III VAR36=FUER NX8300 MIT 6 VERSTAERKER BAND III MOD36=FOR NX8300 WITH 6 AMPLIFIER BAND III VAR41=FUER NX8300 MIT 1 VERSTAERKER BAND IV/V MOD41=FOR NX8300 WITH 1 AMPLIFIER BAND IV/V VAR42=FUER NX8300 MIT 2 VERSTAERKER BAND IV/V MOD42=FOR NX8300 WITH 2 AMPLIFIER BAND IV/V VAR43=FUER NX8300 MIT 3 VERSTAERKER BAND IV/V MOD43=FOR NX8300 WITH 3 AMPLIFIER BAND IV/V VAR44=FUER NX8300 MIT 4 VERSTAERKER BAND IV/V MOD44=FOR NX8300 WITH 4 AMPLIFIER BAND IV/V VAR45=FUER NX8300 MIT 5 VERSTAERKER BAND IV/V MOD45=FOR NX8300 WITH 5 AMPLIFIER BAND IV/V VAR46=FUER NX8300 MIT 6 VERSTAERKER BAND IV/V
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLISTE ZR800C1 LEISTUNGSS.SPARE PART LIST FOR 2098.5009.01Sprach./Langde en Ä.I. / C.I04.00 Blatt/Sheet2 of 10Dokument Nr. / Document No.2098.5067.01 STZR800C1 Datum/Date 2009-07-09 Abt. /Dept. 7TSK Name /Name RO MOD46=FOR NX8300 WITH 6 AMPLIFIER BAND IV/V VAR51=FUER NX8300X1 MIT 1 VERSTAERKER BAND III MOD51=FOR NX8300X1 WITH 1 AMPLIFIER BAND III VAR52=FUER NX8300X1 MIT 2 VERSTAERKER BAND III MOD52=FOR NX8300X1 WITH 2 AMPLIFIER BAND III VAR53=FUER NX8300X1 MIT 3 VERSTAERKER BAND III MOD53=FOR NX8300X1 WITH 3 AMPLIFIER BAND III VAR54=FUER NX8300X1 MIT 4 VERSTAERKER BAND III MOD54=FOR NX8300X1 WITH 4 AMPLIFIER BAND III VAR55=FUER NX8300X1 MIT 5 VERSTAERKER BAND III MOD55=FOR NX8300X1 WITH 5 AMPLIFIER BAND III VAR56=FUER NX8300X1 MIT 6 VERSTAERKER BAND III MOD56=FOR NX8300X1 WITH 6 AMPLIFIER BAND III VAR61=FUER NX8300X1 MIT 1 VERSTAERKER BAND IV/V MOD61=FOR NX8300X1 WITH 1 AMPLIFIER BAND IV/V VAR62=FUER NX8300X1 MIT 2 VERSTAERKER BAND IV/V MOD62=FOR NX8300X1 WITH 2 AMPLIFIER BAND IV/V VAR63=FUER NX8300X1 MIT 3 VERSTAERKER BAND IV/V MOD63=FOR NX8300X1 WITH 3 AMPLIFIER BAND IV/V VAR64=FUER NX8300X1 MIT 4 VERSTAERKER BAND IV/V MOD64=FOR NX8300X1 WITH 4 AMPLIFIER BAND IV/V VAR65=FUER NX8300X1 MIT 5 VERSTAERKER BAND IV/V MOD65=FOR NX8300X1 WITH 5 AMPLIFIER BAND IV/V VAR66=FUER NX8300X1 MIT 6 VERSTAERKER BAND IV/V MOD66=FOR NX8300X1 WITH 6 AMPLIFIER BAND IV/V 1000 0 S PB BEMERKUNG 0999.9610.00 B O NOTE Pos.: 1010 bis 1990 HF - Komponenten 1020 1 S A41 ZE BV822M1 2FACH-KOPPLER Z 2099.5502.02 M BV822M1 TWOF. COUPLER VAR 12 32 52 ## Verwendet in: ## 2098.5009.01 1030 1 S A41 ZE BV823M1 3FACH-KOPPLER Z 2099.5702.02 M BV823M1 3F. COUPLER VAR 13 33 53 ## Verwendet in: ## 2098.5009.01 1040 1 S A41 ZE BV824M1 4FACH-KOPPLER Z 2099.5602.02 M BV824M1 QUADRUPLE COUPLER VAR 14 34 54 ## Verwendet in: ## 2098.5009.01 1050 1 S A41 ZE BV825M1 5FACH-KOPPLER Z 2099.5802.02 M
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLISTE ZR800C1 LEISTUNGSS.SPARE PART LIST FOR 2098.5009.01Sprach./Langde en Ä.I. / C.I04.00 Blatt/Sheet3 of 10Dokument Nr. / Document No.2098.5067.01 STZR800C1 Datum/Date 2009-07-09 Abt. /Dept. 7TSK Name /Name RO BV825M1 5F. COUPLER VAR 15 35 55 ## Verwendet in: ## 2098.5009.01 1060 1 S A41 ZE BV826M1 6FACH-KOPPLER Z 2099.5902.02 M BV826M1 6F. COUPLER VAR 16 36 56 ## Verwendet in: ## 2098.5009.01 1120 1 S A41 ZE BV832H1 2FACH-KOPPLER Z 2096.4305.02 M BV832H1 2 WAY COUPLER VAR 22 42 62 ## Verwendet in: ## 2098.5009.01 1130 1 S A41 ZE BV833H1 3FACH-KOPPLER Z 2096.4157.02 M BV833H1 TRIPLE COUPLER VAR 23 43 63 ## Verwendet in: ## 2098.5009.01 1140 1 S A41 ZE BV834H1 4FACH-KOPPLER Z 2096.4005.02 M BV834H1 FOURFOLD COUPL VAR 24 44 64 ## Verwendet in: ## 2098.5009.01 1150 1 S A41 ZE BV835H1 5FACH-KOPPLER Z 2096.4705.02 M BV835H1 FIVEFOLD COUPL VAR 25 45 65 ## Verwendet in: ## 2098.5009.01 1160 1 S A41 ZE BV836H1 6FACH-KOPPLER Z 2096.3750.02 M BV836H1 SIXFOLD COUPL. VAR 26 46 66 ## Verwendet in: ## 2098.5009.01 1220 1 S A42 ZE ABS-BLOCK ML NX8000 Z 2096.3909.32 M ABS BLOCK MP NX8000 VAR 12 13 32 33 52 53 ## Verwendet in: ## 2098.5009.01 1240 1 S A42 ZE ABS-BLOCK ML NX8000 Z 2096.3909.35 M ABS BLOCK MP NX8000 VAR 14 15 16 34 35 36 54 55 56 ## Verwendet in: ## 2098.5009.01 1320 1 S A42 ZE ABS-BLOCK ML NX8000 Z 2096.3909.03 M ABS BLOCK MP NX8000 VAR 22 23 42 43 62 63 ## Verwendet in: ## 2098.5009.01 1340 1 S A42 ZE ABS-BLOCK ML NX8000 Z 2096.3909.02 M ABS BLOCK MP NX8000 VAR 24 25 26 44 45 46 64 65 66 ## Verwendet in: ## 2098.5009.01 1410 1 S A45 ZM FM825 OWF - BD. 3 Z 2096.7304.00 M O FM825 H.FILT. BD. 3 VAR 11 12 13 14 15 16 31 32 33 34 35 36 51 52 53 54 55 56 ## Verwendet in: ## 2098.5009.01 1450 1 S A45 ZM FH825 OWF - BD. 4/5 Z 2096.6508.02 M O FH825 H.FILT. BD. 4/5
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLISTE ZR800C1 LEISTUNGSS.SPARE PART LIST FOR 2098.5009.01Sprach./Langde en Ä.I. / C.I04.00 Blatt/Sheet4 of 10Dokument Nr. / Document No.2098.5067.01 STZR800C1 Datum/Date 2009-07-09 Abt. /Dept. 7TSK Name /Name RO VAR 21 22 23 24 25 26 41 42 43 44 45 46 61 62 63 64 65 66 ## Verwendet in: ## 2098.5009.01 1510 1 S P14 ZE GD800 MESSRICHTKOPPLER Z 2096.7204.34 M DIRECTION COUPLER VAR 11 12 13 14 15 16 31 32 33 34 35 36 51 52 53 54 55 56 ## Verwendet in: ## 2098.5009.01 1520 1 S P14 ZE GD800 MESSRICHTKOPPLER Z 2096.7204.44 M DIRECTION COUPLER VAR 21 22 23 24 25 26 41 42 43 44 45 46 61 62 63 64 65 66 ## Verwendet in: ## 2098.5009.01 1530 1 S P14A ZM GD800Z2 MESSSYSTEM Z 2096.6308.30 M O GD800Z2 MEASURING SYST VAR 11 12 13 14 15 16 31 32 33 34 35 36 51 52 53 54 55 56 ## Verwendet in: ## 2096.7204.01 1540 1 S P14A ZM GD800Z2 MESSSYSTEM Z 2096.6308.40 M O GD800Z2 MEASURING SYST VAR 21 22 23 24 25 26 41 42 43 44 45 46 61 62 63 64 65 66 ## Verwendet in: ## 2096.7204.01 1550 1 S P14B ZM GD800Z2 MESSSYSTEM Z 2096.6308.30 M O GD800Z2 MEASURING SYST VAR 11 12 13 14 15 16 31 32 33 34 35 36 51 52 53 54 55 56 ## Verwendet in: ## 2096.7204.01 1560 1 S P14B ZM GD800Z2 MESSSYSTEM Z 2096.6308.40 M O GD800Z2 MEASURING SYST VAR 21 22 23 24 25 26 41 42 43 44 45 46 61 62 63 64 65 66 ## Verwendet in: ## 2096.7204.01 1570 1 S P14C ZM GD800Z1 MESSSYSTEM Z 2096.6208.02 M O GD800Z1 MEASURING SYST ## Verwendet in: ## 2096.7204.01 1580 1 S P14D ZM GD800Z1 MESSSYSTEM Z 2096.6208.03 M O GD800Z1 MEASURING SYST ## Verwendet in: ## 2096.7204.01 1590 1 S P14ZP ED RF-AUSGANG Z2 Z 2096.6408.02 M O RF_OUTPUT Z2 ## Verwendet in: ## 2096.7204.01 Zum Einstellen der Auskoppeldaempfung fuer P14A, P14B, P14C und P14D. 1610 1 S W.A1 DH KABEL L=1M S/S 7/16 2087.7111.00 B O CABLE VAR 11 21 31 41 51 61 ## Verwendet in: ## 2098.5009.01 1620 1 S X.A ZM UEBERGANG 7/16BU-RL13/30M Z 2096.7004.00 M O Adaptor 7/16BU-RL13/30M VAR 11 21 31 41 51 61 ## Verwendet in: ## 2098.5009.01
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLISTE ZR800C1 LEISTUNGSS.SPARE PART LIST FOR 2098.5009.01Sprach./Langde en Ä.I. / C.I04.00 Blatt/Sheet5 of 10Dokument Nr. / Document No.2098.5067.01 STZR800C1 Datum/Date 2009-07-09 Abt. /Dept. 7TSK Name /Name RO 1630 1 S DV RG400 2XN/W U 1,4M Z 2097.5792.00 M O RF-CABLE VAR 12 13 14 15 16 22 23 24 25 26 32 33 34 35 36 42 43 44 45 46 52 53 54 55 56 62 63 64 65 66 ## Verwendet in: ## 2098.5009.01 1640 1 S DV RG400 2XN/W U 0,6M Z 2097.5805.00 M O RF-CABLE VAR 15 16 25 26 35 36 45 46 55 56 65 66 ## Verwendet in: ## 2098.5009.01 1650 1 S DH KABEL SCF 2XN-W 1.1M U 2097.5863.00 B O RF CABLE VAR 14 15 16 24 25 26 34 35 36 44 45 46 54 55 56 64 65 66 ## Verwendet in: ## 2098.5009.01 1710 1 S ZM UEBERGANG 1 5/8EIA-RL13/30R Z 2096.6966.00 M O Adaptor 1 5/8EIA-RL13/30R ## Verwendet in: ## 2098.5009.01 1720 1 S FK KUPPLUNG EIA 1 5/8 0656.2279.00 B V ADAPTOR FOR TRANSMISSION LINE 1 5/8 ## Verwendet in: ## 2098.5009.01 2000 0 S PB BEMERKUNG 0999.9610.00 B O NOTE Pos.: 2010 bis 2990 Netzverteilung - Komponenten 2010 1 S X1 SL 3PH SAM.SCH. EINSP. LI 2096.5053.00 B O 3PH CURR. DISTRIB. LEF VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3009.01 2020 1 S X1.1 SL 3PH SAM.SCH. ERWEIT.2X 2096.5060.00 B O 3PH CURR. DISTRIB. 2X VAR 13 14 16 23 24 26 33 34 36 43 44 46 ## Verwendet in: ## 2096.3344.01 X1.2 2030 1 S X1.1 SL 3PH SAM.SCH. ERWEIT.3X 2096.5076.00 B O 3PH CURR. DISTRIB. 3X VAR 15 25 36 46 ## Verwendet in: ## 2096.3344.01 2040 1 S X2 VK KLEMMBLOCK 0.5-6QMM 2096.5124.00 B B TERMINAL BLOCK VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3009.01 2050 1 S F1 SS SCHUTZSCHALTER T-M 1P 3A - C 2096.5030.00 B O PROTECT SWITCH 1P 3A - C VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3009.01 F2 F3 F4 F5 F6
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLISTE ZR800C1 LEISTUNGSS.SPARE PART LIST FOR 2098.5009.01Sprach./Langde en Ä.I. / C.I04.00 Blatt/Sheet6 of 10Dokument Nr. / Document No.2098.5067.01 STZR800C1 Datum/Date 2009-07-09 Abt. /Dept. 7TSK Name /Name RO F7 F8 2090 1 S W1PH DX W1PH VERTEILER N-NETZ Z 2096.3538.02 M W1PH MAIN DISTRIBUTOR VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3009.01 2110 1 S Q1 SL LEISTUNGSTRENNER 32A/400V 2093.8522.00 B O MAINSWITCH 32A/400V VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3344.01 2120 1 S Q1.N SL 4.SCHALTGLIED (N-LEIT) 2096.5024.00 B O 4. SWITCH N-CONTACT VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3344.01 2130 1 S Q2 SS SCHUTZSCHALTER T-M 3P 3.5-5A 2096.5153.00 B O PROTECT SWITCH 3P 3.5-5A VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3344.01 Q3 Q4 Q5 Q6 Q7 2140 1 S Q2X SL 3PH VERBINDUNGSSTECKER 2096.5082.00 B O 3PH PLUG LINK VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3344.01 Q3X Q4X Q5X Q6X Q7X 2150 1 S X20.1 VK SCHUTZLEITERKL.2.5QMM 2091.9773.00 B V VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3009.01 X20.2 X20.3 2400 1 S X33 DX WAGO BRUECKEN-STECKER Z 2097.5634.33 M O DUMMY PLUG VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3344.01 2410 1 S X36 DX WAGO BRUECKEN-STECKER Z 2097.5634.36 M O DUMMY PLUG VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3344.01 2420 1 S X41 DX WAGO BRUECKEN-STECKER Z 2097.5634.41 M O DUMMY PLUG VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in:
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLISTE ZR800C1 LEISTUNGSS.SPARE PART LIST FOR 2098.5009.01Sprach./Langde en Ä.I. / C.I04.00 Blatt/Sheet7 of 10Dokument Nr. / Document No.2098.5067.01 STZR800C1 Datum/Date 2009-07-09 Abt. /Dept. 7TSK Name /Name RO ## 2096.3344.01 2430 1 S X42 DX WAGO BRUECKEN-STECKER Z 2097.5634.42 M O DUMMY PLUG VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3344.01 2440 1 S X44 DX WAGO BRUECKEN-STECKER Z 2097.5634.44 M O DUMMY PLUG VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3344.01 2500 1 S A35 ED VERTEILER-N-NETZ Z 2096.3550.02 M INTERFACE POWER DISTR. VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3009.01 2510 1 S A36 NJ SCHALTNETZT. AC90-264V 1081.0254.00 B B POWER SUPPLY 12V/40W VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3009.01 2610 1 S W35 DX W35 NETZKAB.-HILFSSPG. Z 2096.3450.00 M O W35 MAIN POWER KABLE VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3009.01 2620 1 S W45 DX W45 DC-KABEL-HILFSSPG. Z 2096.3444.00 M O W45 DC CABLE VAR 11 12 13 14 15 16 21 22 23 24 25 26 31 32 33 34 35 36 41 42 43 44 45 46 ## Verwendet in: ## 2096.3009.01 3000 0 S PB BEMERKUNG 0999.9610.00 B O NOTE Pos.: 3010 bis 3990 Gestell - Komponenten 3010 1 S A50 EE RACK CONTROLLER Z 2096.4505.02 M O RACK CONTROLLER ## Verwendet in: ## 2098.5009.01 3110 1 S X53A DX CAN ABSCHL. 9POL.X53A Z 2097.5628.00 M O CAN TERMINATING X53A ## Verwendet in: ## 2098.5009.01 3120 1 S X53B DX CAN ABSCHL. 15POL.X53B Z 2097.5611.00 M O CAN TERMINATING X53B ## Verwendet in: ## 2098.5009.01 3130 1 S X53D DX CAN ABSCHL. 15POL.X53D Z 2097.5605.00 M O CAN TERMINATING X53D ## Verwendet in: ## 2098.5009.01 3150 1 S X54B DX BRUECKEN-ST REF.SPG.-REDUZ. A50/X7 Z 2097.5592.00 M DUMMY PLUG REDUCED_REF_B A50/X7 ## Verwendet in: ## 2098.5009.01
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLISTE ZR800C1 LEISTUNGSS.SPARE PART LIST FOR 2098.5009.01Sprach./Langde en Ä.I. / C.I04.00 Blatt/Sheet8 of 10Dokument Nr. / Document No.2098.5067.01 STZR800C1 Datum/Date 2009-07-09 Abt. /Dept. 7TSK Name /Name RO3500 1 S W48 DG PATCHKABEL 2M 1-1 BL 4055.6458.00 B T PATCHCABEL 2M 1-1 BL ## Verwendet in: ## 2098.5009.01 3600 1 M WW DICHTUNGSSCHAUMBAND PVC 8X6 14SH 2096.2119.00 B B SEALING TAPE ## Verwendet in: ## 2096.2002.01 3710 1 S KZ FUEHLSTIFT RD2.7X17.5 0043.5727.00 M V GUIDE PIN VAR 11 12 13 14 21 22 23 24 31 32 33 34 41 42 43 44 51 52 53 54 61 62 63 64 ## Verwendet in: ## 2096.2231.01 3720 1 S MF ANSCHLUSSHALTER 2096.2290.00 M O CONNECTION HOLDER VAR 11 12 13 14 21 22 23 24 31 32 33 34 41 42 43 44 51 52 53 54 61 62 63 64 ## Verwendet in: ## 2096.2231.01 3800 1 S MZ ABDECKUNG 2 2096.2925.00 M O COVER 2 VAR 11 12 13 14 15 21 22 23 24 25 31 32 33 34 35 41 42 43 44 45 51 52 53 54 55 61 62 63 64 65 ## Verwendet in: ## 2099.5019.00 3900 1 S E1 ZE LUEFTERSATZ ML Z 2096.2131.02 M FAN KIT MP VAR 11 12 13 14 15 16 21 22 23 24 25 26 ## Verwendet in: ## 2096.2377.01 E2 3910 1 S SL LEISTUNGSTRENNSCHALTER 63A 2096.5001.00 B O 63A MAIN POWER SWITCH VAR 51 52 53 54 55 61 62 63 64 65 ##Verwendet in: ##2096.2154.01 3920 1 S SL 4.SCHALTGLIED (N-LEIT) 2096.5018.00 B O 4. SWITCH N-CONTACT VAR 51 52 53 54 55 61 62 63 64 65 ##Verwendet in: ##2096.2154.01 3930 1 S SL LEISTUNGSSCHALT.4P125A 2093.8839.00 B O POWER SWITCH 4P 124A VAR 56 66 ##Verwendet in: ##2096.2154.01 3940 1 S SS SCHUTZSCHALTER TM 2P 15A / C 2096.5224.00 B O PROTECT SWITCH 2P 15A - C VAR 51 52 53 54 55 56 61 62 63 64 65 66 ##Verwendet in: ##2096.2154.01 3950 1 S SS SCHUTZSCHALTER T-M 1P 3A - C 2096.5030.00 B O PROTECT SWITCH 1P 3A - C VAR 51 52 53 54 55 56 61 62 63 64 65 66 ##Verwendet in: ##2096.2154.01 3960 1 S SS SCHUTZSCHALTER T-M 1P 6A - C 2096.5047.00 B O PROTECT SWITCH 1P 6A - C VAR 51 52 53 54 55 56 61 62 63 64 65 66 ##Verwendet in: ##2096.2154.01
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLISTE ZR800C1 LEISTUNGSS.SPARE PART LIST FOR 2098.5009.01Sprach./Langde en Ä.I. / C.I04.00 Blatt/Sheet9 of 10Dokument Nr. / Document No.2098.5067.01 STZR800C1 Datum/Date 2009-07-09 Abt. /Dept. 7TSK Name /Name RO 3970 1 S ED VERTEILER-N-NETZ Z 2096.3550.02 M INTERFACE POWER DISTR. VAR 51 52 53 54 55 56 61 62 63 64 65 66 ##Verwendet in: ##2096.2154.01 3980 1 S DX WAGO BRUECKEN-STECKER Z 2097.5634.33 M O DUMMY PLUG VAR 51 52 53 54 55 56 61 62 63 64 65 66 ##Verwendet in: ##2096.2154.01 3990 1 S DX WAGO BRUECKEN-STECKER Z 2097.5634.36 M O DUMMY PLUG VAR 51 52 53 54 55 56 61 62 63 64 65 66 ##Verwendet in: ##2096.2154.01 4000 1 S DX WAGO BRUECKEN-STECKER Z 2097.5634.41 M O DUMMY PLUG VAR 51 52 53 54 55 56 61 62 63 64 65 66 ##Verwendet in: ##2096.2154.01 4010 1 S DX WAGO BRUECKEN-STECKER Z 2097.5634.42 M O DUMMY PLUG VAR 51 52 53 54 55 56 61 62 63 64 65 66 ##Verwendet in: ##2096.2154.01 4020 1 S DX WAGO BRUECKEN-STECKER Z 2097.5634.44 M O DUMMY PLUG VAR 51 52 53 54 55 56 61 62 63 64 65 66 ##Verwendet in: ##2096.2154.01 4030 1 S NJ SCHALTNETZT. AC90-264V 1081.0254.00 B B POWER SUPPLY 12V/40W VAR 51 52 53 54 55 56 61 62 63 64 65 66 ##Verwendet in: ##2096.2154.01 4040 1 S DX AC 1PH A1.VERST. KAB. W61 Z 2097.4850.00 M AC 1PH A1.AMPLIF.CAB. W61 VAR 51 52 53 54 55 56 61 62 63 64 65 66 ##Verwendet in: ##2096.2154.01 4050 1 S DX AC 1PH A2.VERST. KAB. W62 Z 2097.4867.00 M AC 1PH A2.AMPLIF.CAB. W62 VAR 52 53 54 55 56 62 63 64 65 66 ##Verwendet in: ##2096.2154.01 4060 1 S DX AC 1PH A3.VERST. KAB. W63 Z 2097.4873.00 M AC 1PH A3.AMPLIF.CAB. W63 VAR 53 54 55 56 63 64 65 66 ##Verwendet in: ##2096.2154.01 4070 1 S DX AC 1PH A4.VERST. KAB. W64 Z 2097.4880.00 M AC 1PH A4.AMPLIF.CAB. W64 VAR 54 55 56 64 65 66 ##Verwendet in: ##2096.2154.01 4080 1 S DX AC 1PH A5.VERST. KAB. W65 Z 2097.4896.00 M AC 1PH A5.AMPLIF.CAB. W65 VAR 55 56 65 66 ##Verwendet in: ##2096.2154.01 4090 1 S DX AC 1PH A6.VERST. KAB. W66 Z 2097.4909.00 M AC 1PH A6.AMPLIF.CAB. W66
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLISTE ZR800C1 LEISTUNGSS.SPARE PART LIST FOR 2098.5009.01Sprach./Langde en Ä.I. / C.I04.00 Blatt/Sheet10 of 10Dokument Nr. / Document No.2098.5067.01 STZR800C1 Datum/Date 2009-07-09 Abt. /Dept. 7TSK Name /Name RO VAR 56 66 ##Verwendet in: ##2096.2154.01
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLISTE ZR800V1 VORSTUFENS.SPARE PART LIST FOR 2099.1507.01Sprach./Langde en Ä.I. / C.I03.00 Blatt/Sheet1 of 1Dokument Nr. / Document No.2099.1513.01 STZR800V1 Datum/Date 2008-11-05 Abt. /Dept. 7TS4 Name /Name BM ACHTUNG EGB/ATTENTION ESD *VARIANTENERKLAERUNG *EXPLANATION OF MODELS VAR02=ATV-SPLIT AUSFUEHRUNG MOD02=ATV SPLIT VERSION VAR03=ATV-COMB. AUSFUEHRUNG MOD03=ATV COMBINED VERSION VAR04=DTV - AUSFUEHRUNG MOD04=DTV VERSION VAR05=DTV - AUSFUEHRUNG MIT ADE MOD05=DTV VERSION WITH ADE VAR06=DAB - AUSFUEHRUNG ML MIT SX801 MOD06=DAB VERSION MP WITH SX801 VAR24=DTV - KLEINLEISTUNG MOD24=DTV LOW POWER VAR25=DTV+ADE KLEINLEISTUNG MOD25=DTV+ADE LOW POWER 100 1 S A15 ED HF-STEUERS.UMSCH. Z 2095.3305.02 M O RF-EXCITER SWITCHING VAR 02 03 05 25 ## Verwendet in: ## 2099.1507.01 200 1 S A15 ED RF-SWITCH Z 2095.3257.02 M O RF-SWITCH VAR 04 06 24 ## Verwendet in: ## 2099.1507.01 300 1 S W11B DX AF-Kabel W11-12-13B Z 2097.5440.00 M O AF-Cable W11-12-13B VAR 02 03 ## Verwendet in: ## 2099.1507.01 W12B W13B 400 1 S W21B DV RG179D BNC BU-E/BNC ST Z 2097.5857.00 M RF-CAB. 75 OHM 2000MM VAR 02 03 04 05 06 ## Verwendet in: ## 2099.1507.01 W22B W23B W24B W31B W32B W34B W35B W42B 500 1 S W41B DV RG316 BNC-St/EBU 2000MM Z 2088.3503.00 M RF CABLE 50 OHM 2XBNC VAR 02 03 04 05 06 ## Verwendet in: ## 2099.1507.01 W43B 510 1 S A100R ED RACK CONTROLLER SV8000 Z 2098.9740.02 M RACK CONTROLLER SV8000 VAR 24 25 ## Verwendet in: ## 2099.1507.01
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLI. ZR800T1 EINBAUS.SX800SPARE PART LIST FOR 2099.1007.01Sprach./Langde en Ä.I. / C.I04.00 Blatt/Sheet1 of 2Dokument Nr. / Document No.2099.1013.01 STZR800T1 Datum/Date 2009-07-03 Abt. /Dept. 3TSS Name /Name KA ACHTUNG EGB/ATTENTION ESD *VARIANTENERKLAERUNG *EXPLANATION OF MODELS VAR02=ATV-AUSFUEHRUNG FUER ML MOD02=ATV VERSION FOR MP VAR03=DTV-AUSFUEHRUNG FUER ML MOD03=DTV VERSION FOR MP VAR04=DAB-AUSFUEHRUNG FUER ML MIT SX801 MOD04=DAB VERSION FOR MP WITH SX801 VAR22=ATV-AUSFUEHRUNG FUER HL MOD22=ATV VERSION FOR HP VAR23=DTV-AUSFUEHRUNG FUER HL MOD23=DTV VERSION FOR HP VAR24=DAB-AUSFUEHRUNG FUER HL MIT SX801 MOD24=DAB VERSION FOR HP WITH SX801 100 1 S W11A DX AF-KABEL W11-12-13A Z 2097.5434.00 M O AF-CABLE W11-12-13A VAR 02 22 ## Verwendet in: ## 2099.1007.01 W12A W13A 200 5 S W21A DV RG179D BNC BU-E/BNC ST Z 2097.5857.00 M RF-CAB. 75 OHM 2000MM ## Verwendet in: ## 2099.1007.01 W22A W23A W24A W31A W32A W34A W35A W42A 300 2 S W41A DV RG316 BNC-St/EBU 2000MM Z 2088.3503.00 M RF CABLE 50 OHM 2XBNC ## Verwendet in: ## 2099.1007.01 W43A 400 1 S X100A FT EINBAUADAPTER 8P.GER 1093.9122.00 B V 2XRJ45 COUPLER JACK STRAIGHT ## Verwendet in: ## 2099.1007.01 410 1 S W48 DG PATCHKABEL 2M 1-1 BL 4055.6458.00 B T PATCHCABEL 2M 1-1 BL VAR 22 23 24 ## Verwendet in: ## 2099.1007.01 420 1 S W54A DY RACK CONT.-EXC. A W54A Z 2097.5392.00 M O RACK CONT.-EXC. A W54A VAR 22 23 24 ## Verwendet in: ## 2099.1007.01 430 1 S W55 DY RACK CONT.-NETCCU W55 Z 2097.5411.00 M O RACK CONT.-NETCCU W55 VAR 22 23 24 ## Verwendet in: ## 2099.1007.01 440 1 S W56A DG PATCHKABEL CAT6. 0.5M 0041.9283.00 B T PATCHCABLE CAT.6. 0.5M VAR 22 23 24
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLI. ZR800T1 EINBAUS.SX800SPARE PART LIST FOR 2099.1007.01Sprach./Langde en Ä.I. / C.I04.00 Blatt/Sheet2 of 2Dokument Nr. / Document No.2099.1013.01 STZR800T1 Datum/Date 2009-07-03 Abt. /Dept. 3TSS Name /Name KA ## Verwendet in: ## 2099.1007.01 450 1 S X54B DX BRUECKEN-ST REF.SPG.-REDUZ. A50/X7 Z 2097.5592.00 M DUMMY PLUG REDUCED_REF_B A50/X7 VAR 22 23 24 ## Verwendet in: ## 2099.1007.01
Für diese Unterlage behalten wir uns alle Rechte vor.Ausgedruckte Dokumente unterliegen nicht dem Änderungsdienst.For this document all rights are reserved.Printed documents are not subject to revision_ Pos.-Nr. ItemNo MengeQuantity MEUnit El.KennzRef.Des. Benennung / BezeichnungDesignation Z SachnummerStock No. ErsatzteilSubst.part BA VH Benennung/DesignationERSATZTEILLISTE KL830M1 LUFTSATZ MLSprach./Langde en Ä.I. / C.I02.00 Blatt/Sheet1 of 1Dokument Nr. / Document No.2096.2383.01 STKL830M1 Datum/Date 2008-08-01 Abt. /Dept. 7TSK Name /Name RO ACHTUNG EGB/ATTENTION ESD *VARIANTENERKLAERUNG *EXPLANATION OF MODELS VAR02=ZULUFT OBEN MOD02=AIR INLET TOP VAR03=ZULUFT UNTEN MOD03=AIR INLET BOTTOM VAR04=ABLUFT OBEN MOD04=AIR OUTLET TOP VAR05=ABLUFT UNTEN MOD05=AIR OUTLET BOTTOM VAR10=LUEFTERSATZ ML 210L/S 50/60HZ MOD10=FAN KIT ML 210L/S 50/60HZ VAR12=LUEFTERSATZ ML 190L/S - 115V AC 50/60HZ MOD12=FAN KIT ML 190L/S - 115V AC 50/60HZ 10 1 S ZM TEMPERATURFUEHLER Z 2010.0006.00 M THERMOMETER PROBE VAR 04 05 ## Verwendet in: ## 2096.2377.01 20 1 S ZE LUEFTERSATZ ML Z 2096.2131.02 M FAN KIT MP VAR 10 ## Verwendet in: ## 2096.2377.01 30 1 S ZE LUEFTERSATZ ML Z 2096.2131.12 M FAN KIT MP VAR 12 ## Verwendet in: ## 2096.2377.01 120 1 S CM 8UF 400V D40 L70 M8 2092.8287.00 B V MOTOR CAPACITOR VAR 02 ## Verwendet in: ## 2096.2131.01 130 1 S CM 32UF 5% 400V RD45XH95 KABEL 250MM 2096.2548.00 B O MOTOR CAPACITOR 32UF 5% 400V VAR 12 ## Verwendet in: ## 2096.2131.01

Navigation menu