Sharp HRO00024 Cordless Telephone System User Manual for Handset

Download:
Mirror Download [FCC.gov]
Document ID	239274
Application ID	I+mgNNajFcHc0WHybyr7dw==
Document Description	Users Manual for Handset
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	40.6kB (507502 bits)
Date Submitted	2002-04-26 00:00:00
Date Available	2002-06-19 00:00:00
Creation Date	2002-04-05 16:35:05
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2002-04-09 16:50:36
Document Title	Users Manual for Handset

MODEL
UX-K01
se
sH
lesANUAL
z C TION M
2.4GH
OPER
Charge the battery for about 10 hours before initial use.
Introduction
Connecting the Cordless Handset Charger
Installing and Charging the Battery
Registering the Cordless Handset
Enterring a Name for the Cordless Handset
Maintenance
setup.fm
Page 1
Friday, April 5, 2002
4:28 PM
Introduction
To use the UX-K01
cordless handset, you
must have a UX-CC500
fax machine.
Thank you for
purchasing a UX-K01
cordless handset.
Accessories
Battery
cover
Battery
pack
AC adapter
Cordless
handset charger
Specifications
Frequency
2.4 GHz (2.405 to 2.475 GHz)
Dimensions
Width: 1.8" (46 mm)
Depth: 1.7" (42 mm)
Height: 7.1" (180 mm) (not including antenna)
Weight
Approx. 0.3 lbs. (115 g) (without battery)
Battery
3.6 V Ni-MH battery; capacity: 850 mAh
Power consumption
Initial charging
Battery life
Battery life in standby
mode
Approx. 1.0 W (in standby mode)
Approx. 10 hours for initial charge
Approx. 4 hours (240 minutes) (at room temp.)
Approx. 3 days with one full charge (at room
temperature)
Battery life (both normal and in standby mode)
may vary depending on usage, range from base
machine, and environmental conditions such as
temperature.
As a part of our policy of continuous improvement, SHARP reserves the right to make design
and specification changes for product improvement without prior notice. The performance
specification figures indicated are nominal values of production units. There may be some
deviations from these values in individual units.
setup.fm
Page 2
Friday, April 5, 2002
4:28 PM
Important safety information
Do not disassemble this product or attempt any procedures not described in this manual. Refer
all servicing to qualified service personnel.
Do not this product near water, or when you are wet. For example, do not use this product near
a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming
pool. Take care not to spill any liquids on the product.
Unplug the product from the power outlet and consult a qualified service representative if any
of the following situations occur:
- Liquid has been spilled into the product or the product has been
exposed to rain or water.
- The product produces odors, smoke, or unusual noises.
- The power cord is frayed or damaged.
- The product has been dropped or the housing damaged.
Do not allow anything to rest on the power cord, and do not install the product where people
may walk on the power cord.
The AC adapter must only be connected to a 120 V, 60 Hz outlet. Connecting it to any other
kind of outlet will damage the machine and void the warranty.
Never insert objects of any kind into slots or openings on the product. This could create a risk
of fire or electric shock. If an object falls into the product that you cannot remove, unplug the
product and consult a qualified service representative.
Do not place this product on an unstable cart, stand or table. The product could be seriously
damaged if it falls.
Battery
Use only the battery specified in this manual. Use only the provided charger to charge the
battery.
Do not open or mutilate the battery pack. Corrosive fluid may leak out and cause injury or
burns to the eyes and skin. The fluid may be toxic if swallowed. In case of contact with eyes,
flush with clean water (do not rub), and seek medical attention immediately.
Do not store or carry the battery with other metal objects such as keys or pins. These may
short the battery and cause it to overheat.
Do not allow the battery to become wet.
Do not dispose of the battery in a fire or heat the battery. The battery may explode.
Health care facilities and equipment
Radio frequency energy emitted from the cordless handset equipment may cause medical
equipment to malfunction. Verify that any personal medical equipment you are using is
adequately shielded from external radio frequency energy before using the cordless handset
equipment. Do not use the cordless handset equipment in health care facilities where such
use is prohibited.
setup.fm
Page 3
Friday, April 5, 2002
4:28 PM
Connecting the Cordless Handset Charger
Connect the AC adapter to the
cordless handset charger.
Plug the AC adapter into a standard
120 V AC outlet.
Place the cord
in the holders.
Important: Never cover the charger and
AC adapter with a blanket, cloth, or
other material. Excessive heating may
result, causing a fire.
Installing and Charging the Battery
Connect the battery connector ➊, and then place the battery pack in the
cordless handset.
Red
Black
Red
Black
Place the battery cover on the cordless
handset, making sure it snaps firmly
into place.
• Make sure the wires are not caught or
pinched by the cover.
setup.fm
Page 4
Friday, April 5, 2002
4:28 PM
Place the cordless handset in the
charger with the dial pad facing
forward.
• Important! The dial pad must face
forward, or the battery will not charge.
• The battery charges automatically while
the cordless handset is in the charger.
While charging, the display shows
CHARGING.
• When charging is completed the first
time, the display shows PLEASE
REGISTER. After the handset is
registered, the display shows IN
CHARGER while in the charger.
Charge the battery
at least 10 hours
the first time!
♦ The cordless handset and charger may feel warm while charging. This is
normal.
♦ The battery cannot be overcharged. When not using the cordless handset,
keep it in the charger to ensure that it is always charged.
When the battery needs charging, LOW BATTERY will appear in the display
and you will hear beeps during a phone conversation. Place the cordless
handset in the charger and let it charge.
Note: If the battery is extremely low, nothing may appear in the display during
the first several minutes that the cordless handset is in the charger. The
battery will begin to charge normally after several minutes.
Talking range
The talking range of the cordless handset is approximately 1200 ft. (400 m)
(line of sight). If you hear noise or interference while talking on the cordless
handset, move closer to the fax machine.
♦ When outside the talking range, OUT OF RANGE appears in the display. If
you move out of the talking range while talking on the cordless handset,
the handset will beep and you may hear interference.
Aluminum sash Metal Reinforced concrete
Large metal objects,
metal structures, and
thick walls reduce the
talking range.
setup.fm
Page 5
Friday, April 5, 2002
4:28 PM
Registering the Cordless Handset
After the initial charging,
the cordless handset
display shows:
PLEASE REGISTER
On the cordless handset, hold down
INTER
COM
To use the cordless
handset, you must
first register it using
the fax machine.
until the display at right appears.
Press 1
on the cordless handset.
Cordless handset display:
MODE SELECT
1: HS ENTRY
2: HS DELETE
HS ENTRY MODE
• If FAX BUSY appears in the display,
wait until the fax machine is no longer in
use and then start from Step 1 again.
INTERCOM
On the fax machine, hold down
until the display at right appears.
Fax machine display:
MODE SELECT
1: HS ENTRY
2: HS DELETE
Press
on the fax machine.
PRESS HS NUMBER
• If HS FULL ENTRY appears in the display, the maximum number (4) of
cordless handsets have already been registered.
On the fax machine, enter a number
from 2 to 4. This number identifies the
cordless handset. This completes the
registration procedure.
Example: “2” is selected
HS2 ENTERED
HS2 ENTERED
• If ALREADY STORED appears in the
display, the number you selected has
already been assigned to a cordless
handset. Try a different number.
Both displays return to the
normal standby display
setup.fm
Page 6
Friday, April 5, 2002
4:28 PM
The fax machine is identified
by the number “0”, and the
cordless handset that was
included with the fax is
identified by the number “1”.
Entering a Name for the Cordless Handset
Enter a name for the cordless handset in the fax machine.
♦ The fax machine will transmit the name that you enter to your cordless
handset.
Press FUNCTION once and
the fax machine.
3 times on
Fax machine display:
ENTRY MODE
Press
once and
Press
once.
1=SET, 2=CLEAR
Press
to select SET.
SELECT ID NO.
Enter the number of the cordless
handset for which you wish to enter a
name.
Example:
once.
HS NAME SET
Example: Cordless handset 2
SELECT ID NO. 2
setup.fm
Page 7
Friday, April 5, 2002
4:47 PM
Enter the name by pressing number keys for each letter as shown in the
chart below. Up to 10 characters can be entered.
Example: BILL = 22 444 555
555
G=
N=
A=
H=
O=
V=
B=
I =
P=
W=
SPACE =
U=
C=
J=
Q=
X=
D=
K=
R=
Y=
E=
L=
S=
Z=
F=
M=
T=
♦ To enter two letters in succession that require the same key, press
after entering the first letter.
♦ To clear a mistake, press
SPEAKER
♦ To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears.
♦ To enter one of the following symbols, press
or
./!"#$%&’()++,-:;<=>?@[¥]^_'{|}
♦ 7Press
START/MEMORY
to store the name.
repeatedly:
)(
Display:
OWN NUMBER
Press
STOP
The handset number and name
appear in the standby display:
to exit.
HANDSET2
BILL
For information on
operating the
cordless handset,
see your UX-CC500
manual.
The cordless
handset is now
ready to be used!
setup.fm
Page 8
Friday, April 5, 2002
4:28 PM
Maintenance
Replacing the Cordless Handset Battery
If LOW BATTERY continues to appear in the cordless handset display after
the battery has been charged for 10 hours, replace it with the following
battery:
Replacement battery: Use only a Sharp UX-BA01 battery
(3.6 V Ni-MH battery, capacity: 850 mAh)
Caution:
There is a danger of explosion if the battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions.
Battery disposal
The battery pack contains a Nickel Metal Hydride battery. The battery must be
disposed of properly. Contact local agencies for information on recycling and
disposal plans in your area.
Deleting (changing) the cordless handset name
Follow the steps below if you need to delete the cordless handset name. If
you wish to change the name, delete it and then enter a new name.
Press FUNCTION once and
the fax machine.
3 times on
Fax machine display:
ENTRY MODE
Press
once and
Press
once.
1=SET, 2=CLEAR
Press
to select CLEAR.
SELECT ID NO.
Enter the number of the cordless handset for which you wish to clear
the name.
Press
START/MEMORY
once.
HS NAME SET
to clear the name and then press
STOP
to exit.
setup.fm
Page 9
Friday, April 5, 2002
4:28 PM
Deleting a cordless handset
If you wish to stop using a cordless handset, follow these steps to delete it
(cancel the registration in the fax machine).
On the cordless handset, hold down
INTER
COM
until the display at right appears.
Press
on the cordless handset.
Cordless handset display:
MODE SELECT
1: HS ENTRY
2: HS DELETE
Example: Cordless handset 2
HS2 DELETE: OK
PRESS START KEY
Press
On the fax machine, hold down
until the display at right appears.
START
on the cordless handset.
PLEASE REGISTER
Fax machine display:
INTERCOM
MODE SELECT
1: HS ENTRY
2: HS DELETE
Press
On the fax machine, enter the number
of the cordless handset that you wish
to delete.
Press
PRESS HS NUMBER
on the fax machine.
START/MEMORY
Example: Cordless handset 2
HS2 DELETED?
on the fax machine.
Note: To ensure correct operation, be sure to perform the deletion procedure
both on the cordless handset and on the fax machine, as explained above.
setup.fm
Page 10
Friday, April 5, 2002
4:28 PM
FCC regulatory information
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment
not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT NOTICE
For body worn operation, this phone has been tested and meets FCC RF exposure guidelines
when used with an accessory that no metal and that positions the handset a minimum of
1.5cm from the body.
Use of other accessories may not ensure compliance with FCC RF exposure guidelines.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On
the rear of this equipment is a label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice isn't practical,
the telephone company will notify the customer as soon as possible. Also, you will be advised of your
right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that
could affect the operation of the equipment. If this happens the telephone company will provide advance
notice in order for you to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, or for repair or warranty information, please contact
Sharp's Customer Assistance Center. The number is 1-877-794-8675. If the equipment is causing harm
to the telephone network, the telephone company may request that you disconnect the equipment until
the problem is resolved.
This equipment contains no user-repairable parts. Refer all servicing to qualified service personnel.
This equipment is hearing aid compatible.
This accessory cordless handset, along with the base unit, has received TCB approval.
10
warranty-cordless2.fm
Page 1
Friday, April 5, 2002
4:31 PM
END USER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first end user purchaser that this Sharp
brand product (the "Product"), when shipped in its original container, will be free from defective
workmanship and materials, and agrees that it will, at its option, either repair the defect or replace
the defective Product or part thereof with a new or remanufactured equivalent at no charge to the
purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded
item(s) set forth below nor to any product the exterior of which has been damaged or defaced,
which has been subjected to misuse, abnormal service or handling, or which has been altered or
modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set
forth below and provided proof of purchase to the servicer.
To the extent permitted by applicable state law, the warranties set forth herein are in lieu of, and
exclusive of, all other warranties, express or implied. Specifically, ALL OTHER WARRANTIES
OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED. ALL EXPRESS AND IMPLIED
WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE,
AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. If, under
applicable state law, implied warranties may not validly be disclaimed or excluded, the duration of
such implied warranties is limited to the period(s) from the date of purchase set forth below.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties
other than those described above, or to extend the duration of any warranties beyond the time
period described above on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and
shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the
manner and for the period of time described herein, shall constitute complete fulfillment of all
liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall
constitute full satisfaction of all claims, whether based on contact, negligence, strict liability or
otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects
in the Product which were caused by repairs or attempted repairs performed by anyone other than
an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or
consequential economic or property damage. Some states do not allow limits on warranties or on
remedies for breach in certain transactions; in such state the limits herein may not apply.
Your Product:
Warranty Period for this Product:
Additional items excluded
from warranty coverage:
Personal Facsimile UX-K01
Ninety (90) days parts and labor from date of purchase.
Any consumable items such as paper or Imaging Film supplied with
the Product.
What to do to obtain service:
Call Sharp at 1-877-794-8675 to obtain a Return Authorization Number and
shipping instructions. A technician will troubleshoot your problem with you
on the phone and if it is determined that your Product needs service, you
will have your choice of having your unit repaired or replaced to any U.S.
location. Be sure to have Proof of Purchase available.
For product information or customer assistance, please visit http://www.sharpusa.com on the
World Wide Web or call 1-877-794-8675.
SHARP ELECTRONICS CORPORATION
Sharp Plaza,
Mahwah, New Jersey 07430-2135
11
warranty-cordless2.fm
Page 2
Friday, April 5, 2002
4:31 PM
IMPORTANT SERVICE INFORMATION
If a Problem Occurs
Most operational questions can be answered by referring to this "Setup Guide and Operation Manual"
Also, for your convenience, you will find answers to most frequently asked
questions on our website at www.sharpusa.com/, or by sending e-mail to faxsupport@sharpsec.com.
Should you require further assistance, call 1-877-794-8675; a Customer Relations Specialist will
assist you. Before your call, please be ready to provide the model number of your product, serial
number, date of purchase, description of the problem, and a valid credit card number (should it be
required).
How Exchange is Obtained
A replacement unit in exchange for your fax is provided by Sharp to any U.S. location. You will be
required to provide consent for acceptance of an exchange unit and provide credit card authorization.
At that time, Sharp will ship to you, at no cost, an exchange for your defective product. The exchange
unit we ship to you will be new or remanufactured. Upon your receipt of the exchange unit, packaging
and shipping instructions will be enclosed for you to return the defective unit. Upon Sharp's receipt of
the defective unit, your credit card hold will be released.
How Warranty Repair Service is Obtained
If you prefer that we repair your unit instead of replacing it, our Customer Relations Specialists at 1877-794-8675 will explain how to obtain warranty repair service. Please be sure to retain the
original packaging materials in order to facilitate shipment. Upon repair of your unit, Sharp will
promptly return it at no cost to you at any U.S. location.
Service After Expiration of Warranty Coverage
Should you require service repair after warranty coverage has expired, contact Sharp at 1-877-7948675 for information.
To Purchase Consumables From Sharp
Visit www.sharpplace.com/ or call Sharp at 1-877-794-8675 to order replacement Sharp Thermal
Ribbons & Accesories. Before your call, please be ready to provide the model number of your
product, and a valid credit card number. Consumables may also be obtained through your reseller.
back.fm
Page 139
Friday, April 5, 2002
4:31 PM
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
http://www.sharpusa.com
SHARP CORPORATION
FOR YOUR RECORDS
Please record the model number and serial number below, for easy
reference, in case of loss or theft. These numbers are located on the
rear side of the unit. Space is also provided for other relevant
information.
Model Number
UX-K01
Serial Number
Date of Purchase
Place of Purchase
PRINTED IN THAILAND
(TCADH3390XHZZ)

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2002:04:05 16:35:05
Producer                        : Acrobat Distiller 4.05 for Windows
Modify Date                     : 2002:04:09 16:50:36+09:00
Page Count                      : 14

EXIF Metadata provided by EXIF.tools