Siemens Canada Siemens Milltronics Process Instruments LR250 SITRANS LR 250 TANK LEVEL PROBING RADAR User Manual SITRANS LR250 mA HART
Siemens Canada Ltd. - Siemens Milltronics Process Instruments SITRANS LR 250 TANK LEVEL PROBING RADAR SITRANS LR250 mA HART
Contents
User Manual 1
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2277916 |
| Application ID | b6dzDHyWYrt2RbmEr0PsvQ== |
| Document Description | User Manual 1 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 354.99kB (4437346 bits) |
| Date Submitted | 2014-05-27 00:00:00 |
| Date Available | 2014-05-27 00:00:00 |
| Creation Date | 2014-05-21 10:54:45 |
| Producing Software | Adobe PDF Library 10.0 |
| Document Lastmod | 2014-05-21 10:55:37 |
| Document Title | SITRANS LR250 (mA/HART) |
| Document Creator | Acrobat PDFMaker 10.1 for Word |
| Document Author: | IIA SC PI 2 TP |
Radar Transmitters SITRANS LR250 (mA/HART) Operating Instructions 08/2014 SITRANS Safety Guidelines Warning notices must be observed to ensure personal safety as well as that of others, and to protect the product and the connected equipment. These warning notices are accompanied by a clarification of the level of caution to be observed. Qualified Personnel This device/system may only be set up and operated in conjunction with this manual. Qualified personnel are only authorized to install and operate this equipment in accordance with established safety practices and standards. Unit Repair and Excluded Liability: The user is responsible for all changes and repairs made to the device by the user or the user’s agent. All new components are to be provided by Siemens Milltronics Process Instruments. Restrict repair to faulty components only. Do not reuse faulty components. Warning: Cardboard shipping package provides limited humidity and moisture protection. This product can only function properly and safely if it is correctly transported, stored, installed, set up, operated, and maintained. This product is intended for use in industrial areas. Operation of this equipment in a residential area may cause interference to several frequency based communications. Note: Always use product in accordance with specifications. Copyright Siemens AG 2013. All Rights Reserved Disclaimer of Liability This document is available in bound version and in electronic version. We encourage users to purchase authorized bound manuals, or to view electronic versions as designed and authored by Siemens Milltronics Process Instruments. Siemens Milltronics Process Instruments will not be responsible for the contents of partial or whole reproductions of either bound or electronic versions. While we have verified the contents of this manual for agreement with the instrumentation described, variations remain possible. Thus we cannot guarantee full agreement. The contents of this manual are regularly reviewed and corrections are included in subsequent editions. We welcome all suggestions for improvement. Technical data subject to change. MILLTRONICS®is a registered trademark of Siemens Milltronics Process Instruments. Contact SMPI Technical Publications at the following address: European Authorized Representative Technical Publications Siemens AG Siemens Milltronics Process Instruments 1954 Technology Drive, P.O. Box 4225 Peterborough, Ontario, Canada, K9J 7B1 Email: techpubs.smpi@siemens.com Siemens AG Industry Sector 76181 Karlsruhe Deutschland For a selection of Siemens Milltronics level measurement manuals, go to: www. siemens.com/processautomation. Under Process Instrumentation, select Level Measurement and then go to the manual archive listed under the product family. For a selection of Siemens Milltronics weighing manuals, go to: www. siemens.com/processautomation. Under Weighing Technology, select Continuous Weighing Systems and then go to the manual archive listed under the product family. © Siemens AG 2013 1 ___________________ Introduction SITRANS LR250 (mA/HART) ___________________ Safety information ___________________ Description SITRANS Radar Transmitters SITRANS LR250 (mA/HART) Operating Instructions ___________________ Installing/mounting ___________________ Connecting ___________________ Commissioning ___________________ Remote operation ___________________ Parameter reference ___________________ Service and maintenance Diagnosing and 10 ___________________ troubleshooting 11 ___________________ Technical data 12 ___________________ Dimension drawings Appendix A: Technical ___________________ reference Appendix B: HART ___________________ communications Appendix C: Certificates and ___________________ support 13 ___________________ List of abbreviations 14 ___________________ LCD menu structure 08/2014 A5E32220602-AC Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION indicates that minor personal injury can result if proper precautions are not taken. NOTICE indicates that property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems. Proper use of Siemens products Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed. Trademarks All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Industry Sector Postfach 48 48 90026 NÜRNBERG GERMANY Order number: A5E32220602 Ⓟ 03/2014 Subject to change Copyright © Siemens AG 2014. All rights reserved Table of contents Introduction ............................................................................................................................................. 9 1.1 LR250 mA/HART manual usage.................................................................................................... 9 1.2 Purpose of this documentation ...................................................................................................... 9 1.3 Document history ........................................................................................................................... 9 1.4 Firmware revision history .............................................................................................................10 1.5 Designated use ............................................................................................................................11 1.6 Checking the consignment ...........................................................................................................11 1.7 Transportation and storage ..........................................................................................................12 1.8 Notes on warranty ........................................................................................................................12 Safety information ................................................................................................................................. 13 2.1 2.1.1 2.1.2 2.1.3 2.1.4 2.1.5 Preconditions for safe use ...........................................................................................................13 Safety marking symbols ...............................................................................................................13 Laws and directives .....................................................................................................................13 FCC Conformity ...........................................................................................................................14 Conformity with European directives ...........................................................................................15 CE Electromagnetic Compatibility (EMC) Conformity..................................................................16 2.2 Improper device modifications .....................................................................................................16 2.3 Requirements for special applications .........................................................................................17 2.4 Use in hazardous areas ...............................................................................................................17 Description ............................................................................................................................................ 19 3.1 SITRANS LR250 overview ...........................................................................................................19 3.2 Programming................................................................................................................................20 3.3 Applications ..................................................................................................................................20 3.4 Approvals and certificates ............................................................................................................20 Installing/mounting ................................................................................................................................ 21 4.1 4.1.1 4.1.1.1 Basic safety information ...............................................................................................................21 Pressure applications ...................................................................................................................22 Pressure Equipment Directive, PED, 97/23/EC ...........................................................................23 4.2 Installation location requirements ................................................................................................24 4.3 4.3.1 Proper mounting...........................................................................................................................26 Nozzle design...............................................................................................................................27 SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC Table of contents 4.3.2 4.3.3 4.3.4 4.3.5 Nozzle location ............................................................................................................................ 28 Orientation in a vessel with obstructions ..................................................................................... 31 Mounting on a Stillpipe or Bypass Pipe ...................................................................................... 32 Device orientation ....................................................................................................................... 33 4.4 4.4.1 4.4.2 4.4.3 Installation instructions ................................................................................................................ 34 Threaded versions ...................................................................................................................... 35 Flanged versions ......................................................................................................................... 35 Hygienic versions ........................................................................................................................ 38 4.5 Disassembly ................................................................................................................................ 39 Connecting ........................................................................................................................................... 41 5.1 Basic safety information .............................................................................................................. 41 5.2 Connecting SITRANS LR250 ...................................................................................................... 41 5.3 5.3.1 5.3.2 5.3.3 5.3.4 5.3.5 5.3.6 Wiring setups for hazardous area installations ........................................................................... 45 Intrinsically safe wiring ................................................................................................................ 45 Non-sparking wiring .................................................................................................................... 47 Non-incendive wiring (US/Canada only) ..................................................................................... 47 Flameproof wiring ........................................................................................................................ 48 Increased safety wiring ............................................................................................................... 49 Explosion-proof wiring (US/Canada only) ................................................................................... 49 5.4 5.4.1 Instructions specific to hazardous area installations ................................................................... 50 (Reference European ATEX Directive 94/9/EC, Annex II, 1/0/6)................................................ 50 Commissioning ..................................................................................................................................... 53 6.1 Basic safety information .............................................................................................................. 53 6.2 6.2.1 6.2.2 6.2.2.1 6.2.2.2 6.2.3 6.2.3.1 6.2.3.2 6.2.3.3 Operating via the handheld programmer .................................................................................... 53 Power up ..................................................................................................................................... 54 Handheld programmer functions ................................................................................................. 54 The LCD display .......................................................................................................................... 55 Handheld programmer (Part No. 7ML1930-1BK) ....................................................................... 57 Programming ............................................................................................................................... 59 Quick Start Wizard via the handheld programmer ...................................................................... 64 Auto False Echo Suppression ..................................................................................................... 68 Requesting an Echo Profile......................................................................................................... 69 6.3 6.3.1 6.3.2 6.3.3 Application examples .................................................................................................................. 70 Liquid resin in storage vessel, level measurement ..................................................................... 71 Horizontal vessel with volume measurement.............................................................................. 72 Application with stillpipe .............................................................................................................. 74 Remote operation ................................................................................................................................. 77 7.1 7.1.1 7.1.1.1 7.1.1.2 Operating via SIMATIC PDM ...................................................................................................... 77 Functions in SIMATIC PDM ........................................................................................................ 77 PDM function overview ............................................................................................................... 77 Features of SIMATIC PDM Rev. 6.0, SP4 or higher ................................................................... 78 SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC Table of contents 7.1.1.3 7.1.1.4 7.1.2 7.1.2.1 7.1.3 7.1.3.1 7.1.4 7.1.5 7.1.6 7.1.6.1 7.1.6.2 7.1.6.3 7.1.6.4 7.1.6.5 7.1.6.6 7.1.6.7 7.1.6.8 7.1.6.9 7.1.6.10 7.1.6.11 7.1.6.12 7.1.6.13 7.1.6.14 7.1.6.15 7.1.6.16 7.1.6.17 7.1.6.18 7.1.6.19 Features of SIMATIC PDM Rev. 5.2, SP1 ...................................................................................78 SIMATIC PDM Version ................................................................................................................78 Initial setup ...................................................................................................................................78 Deactivating buffers .....................................................................................................................79 Updating the Electronic Device Description (EDD) ......................................................................80 Configuring a new device .............................................................................................................80 Quick Start Wizard via SIMATIC PDM .........................................................................................81 Changing parameter settings using SIMATIC PDM ....................................................................86 Parameters accessed via pull-down menus ................................................................................87 Echo profile utilities ......................................................................................................................88 Echo profile ..................................................................................................................................89 View saved echo profiles .............................................................................................................90 TVT Shaper ..................................................................................................................................91 Auto false echo suppression ........................................................................................................92 Echo setup ...................................................................................................................................95 Maintenance.................................................................................................................................95 Select analog output ....................................................................................................................97 Self test ........................................................................................................................................97 Loop test ......................................................................................................................................97 Configuration flag reset ................................................................................................................97 Master reset .................................................................................................................................98 Wear .............................................................................................................................................98 HART Communication .................................................................................................................98 Process variables .........................................................................................................................99 Trend ..........................................................................................................................................100 Device status..............................................................................................................................101 Update ........................................................................................................................................101 Security ......................................................................................................................................102 7.2 7.2.1 7.2.1.1 7.2.1.2 7.2.1.3 7.2.1.4 7.2.1.5 7.2.1.6 7.2.1.7 7.2.1.8 7.2.2 7.2.3 7.2.4 7.2.5 7.2.5.1 7.2.5.2 7.2.5.3 7.2.6 Operating via AMS Device Manager..........................................................................................103 Functions in AMS Device Manager............................................................................................103 AMS function overview ..............................................................................................................103 Features of AMS Device Manager .............................................................................................104 Electronic Device Description (EDD) .........................................................................................104 Configuring a new device ...........................................................................................................104 Startup ........................................................................................................................................105 Pull-down menu access .............................................................................................................106 Device configuration ..................................................................................................................107 Quick Start Wizard via AMS Device Manager ...........................................................................107 Maintenance and diagnostics ....................................................................................................116 Communication ..........................................................................................................................117 Security ......................................................................................................................................118 Device Diagnostics ....................................................................................................................119 Process variables .......................................................................................................................120 Password protection ..................................................................................................................121 User Manager utility ...................................................................................................................121 AMS menu structure ..................................................................................................................122 7.3 Operating via FDT (Field Device Tool) ......................................................................................126 SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC Table of contents 7.3.1 7.3.2 7.3.3 7.3.4 Parameter reference ............................................................................................................................127 8.1 10 11 12 Device Type Manager (DTM) .................................................................................................... 126 SITRANS DTM .......................................................................................................................... 126 The device EDD ........................................................................................................................ 126 Configuring a new device via FDT ............................................................................................ 126 Alphabetical parameter list ........................................................................................................ 179 Service and maintenance .....................................................................................................................183 9.1 Basic safety information ............................................................................................................ 183 9.2 Cleaning .................................................................................................................................... 183 9.3 9.3.1 9.3.2 Maintenance and repair work .................................................................................................... 184 Unit repair and excluded liability ............................................................................................... 185 Part replacement ....................................................................................................................... 185 9.4 Disposal..................................................................................................................................... 187 Diagnosing and troubleshooting ...........................................................................................................189 10.1 Communication troubleshooting ............................................................................................... 189 10.2 Device status icons ................................................................................................................... 190 10.3 General fault codes ................................................................................................................... 192 10.4 Operation troubleshooting ......................................................................................................... 196 Technical data .....................................................................................................................................199 11.1 Power ........................................................................................................................................ 199 11.2 Performance .............................................................................................................................. 199 11.3 Interface .................................................................................................................................... 201 11.4 Mechanical ................................................................................................................................ 202 11.5 Environmental ........................................................................................................................... 205 11.6 Process ..................................................................................................................................... 205 11.7 Approvals .................................................................................................................................. 206 11.8 Programmer (infrared keypad) .................................................................................................. 208 Dimension drawings .............................................................................................................................209 12.1 Threaded horn antenna............................................................................................................. 209 12.2 Threaded horn antenna with extension ..................................................................................... 212 12.3 Flanged horn antenna ............................................................................................................... 214 12.4 Flanged horn antenna with extension ....................................................................................... 216 12.5 Flanged encapsulated antenna (2"/DN50/50A sizes only) ....................................................... 218 12.6 Flanged encapsulated antenna (3"/DN80/80A sizes and larger) .............................................. 220 SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC Table of contents 12.7 Hygienic encapsulated antenna (2" ISO 2852 sanitary clamp) .................................................222 12.8 Hygienic encapsulated antenna (3" ISO 2852 sanitary clamp) .................................................223 12.9 Hygienic encapsulated antenna (4" ISO 2852 sanitary clamp) .................................................224 12.10 Hygienic encapsulated antenna (DN 50 nozzle/slotted nut to DIN 11851) ...............................225 12.11 Hygienic encapsulated antenna (DN 80 nozzle/slotted nut to DIN 11851) ...............................226 12.12 Hygienic encapsulated antenna (DN 100 nozzle/slotted nut to DIN 11851) .............................227 12.13 Hygienic encapsulated antenna (DN 50 aseptic clamp to DIN 11864-1) ..................................228 12.14 Hygienic encapsulated antenna (DN 80 aseptic clamp to DIN 11864-1) ..................................229 12.15 Hygienic encapsulated antenna (DN 100 aseptic clamp to DIN 11864-1) ................................230 12.16 Hygienic encapsulated antenna (DN 50 aseptic flange to DIN 11864-2) ..................................231 12.17 Hygienic encapsulated antenna (DN 80 aseptic flange to DIN 11864-2) ..................................232 12.18 Hygienic encapsulated antenna (DN 100 aseptic flange to DIN 11864-2) ................................233 12.19 Hygienic encapsulated antenna (DN 50 aseptic clamp to DIN 11864-3) ..................................234 12.20 Hygienic encapsulated antenna (DN 80 aseptic clamp to DIN 11864-3) ..................................235 12.21 Hygienic encapsulated antenna (DN 100 aseptic clamp to DIN 11864-3) ................................236 12.22 Hygienic encapsulated antenna (Tuchenhagen Type N) ..........................................................237 12.23 Hygienic encapsulated antenna (Tuchenhagen Type F) ...........................................................238 12.24 Threaded PVDF antenna ...........................................................................................................239 12.25 Threaded connection markings..................................................................................................240 12.26 Raised-Face flange per EN 1092-1 for flanged horn antenna ...................................................241 12.27 Raised-Face flange per EN 1092-1 for flanged encapsulated antenna.....................................243 12.28 Flat-Face flange .........................................................................................................................246 12.29 Aseptic/hygienic flange DN50, DN80, DN100 for DIN 11864-2 .................................................249 12.30 Process connection tag (pressure rated versions) ....................................................................252 Appendix A: Technical reference ......................................................................................................... 253 A.1 Principles of operation ...............................................................................................................253 A.2 A.2.1 A.2.2 A.2.3 A.2.4 A.2.5 A.2.6 A.2.7 A.2.8 Echo Processing ........................................................................................................................254 Process Intelligence ...................................................................................................................254 Echo Selection ...........................................................................................................................255 CLEF Range ..............................................................................................................................258 Echo Threshold ..........................................................................................................................258 Echo Lock ..................................................................................................................................258 Auto False Echo Suppression....................................................................................................259 Measurement Range .................................................................................................................261 Measurement Response ............................................................................................................261 SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC Table of contents A.2.9 Damping .................................................................................................................................... 262 A.3 A.3.1 A.3.2 A.3.3 A.3.4 Analog Output ........................................................................................................................... 262 Sensor Mode ............................................................................................................................. 263 Current Output Function............................................................................................................ 264 Loss of Echo (LOE) ................................................................................................................... 264 Fail-safe Mode .......................................................................................................................... 265 A.4 Maximum Process Temperature Chart ..................................................................................... 265 A.5 A.5.1 A.5.2 A.5.3 A.5.4 A.5.5 A.5.6 Process Pressure/Temperature derating curves ...................................................................... 267 Pressure Equipment Directive, PED, 97/23/EC ........................................................................ 268 Horn antenna ............................................................................................................................ 269 Flanged horn antenna ............................................................................................................... 270 Flanged encapsulated antenna ................................................................................................. 275 PVDF antenna ........................................................................................................................... 277 Hygienic encapsulated antenna ................................................................................................ 278 A.6 A.6.1 A.6.2 A.6.3 Loop power ............................................................................................................................... 281 Allowable operating area of SITRANS LR250 .......................................................................... 281 Curve 1 (General Purpose, Intrinsically Safe, Non-Sparking, Non-incendive) ......................... 282 Curve 2 (Flameproof, Increased Safety, Explosion-proof) ........................................................ 283 A.7 Startup behavior ........................................................................................................................ 283 Appendix B: HART communications .....................................................................................................285 B.1 SIMATIC PDM ........................................................................................................................... 285 B.2 HART Electronic Device Description (EDD) ............................................................................. 285 B.3 HART Handheld 375/475 .......................................................................................................... 285 B.4 HART Communicator 375 menu structure ................................................................................ 286 B.5 B.5.1 B.5.2 HART version ............................................................................................................................ 288 Burst Mode ................................................................................................................................ 288 HART Multidrop Mode ............................................................................................................... 288 Appendix C: Certificates and support ...................................................................................................289 C.1 Certificates ................................................................................................................................ 289 C.2 Technical support ...................................................................................................................... 289 13 List of abbreviations .............................................................................................................................291 14 LCD menu structure .............................................................................................................................293 14.1 LCD menu structure .................................................................................................................. 293 Glossary ..............................................................................................................................................297 Index ...................................................................................................................................................303 SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 1 Introduction 1.1 LR250 mA/HART manual usage Note This manual applies to the SITRANS LR250 mA/HART version only. HART® is a registered trademark of the HART Communication Foundation. Follow these operating instructions for quick, trouble-free installation, and maximum accuracy and reliability of your device. We always welcome suggestions and comments about manual content, design, and accessibility. Please direct your comments to: Technical publications (mailto:techpubs.smpi@siemens.com) 1.2 Purpose of this documentation These instructions contain all information required to commission and use the device. It is your responsibility to read the instructions carefully prior to installation and commissioning. In order to use the device correctly, first review its principle of operation. The instructions are aimed at persons mechanically installing the device, connecting it electronically, configuring the parameters and commissioning it, as well as service and maintenance engineers. 1.3 Document history The following table notes major changes in the documentation compared to the previous edition. Edition Remark January 2014 • Flanged encapsulated antenna version added. August 2014 • Hygienic encapsulated antenna version added. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC Introduction 1.4 Firmware revision history 1.4 Firmware revision history This history establishes the correlation between the current documentation and the valid firmware of the device. The documentation of this edition is applicable for the following firmware: Firmware rev. PDM EDD rev. Date Changes 1.00.03 1.00.03 25 Feb 2007 • Initial release 1.01.00 1.01.00 27 Jul 2007 • EDD a)/SIMATIC PDM: View > Display > Distance b) correctly reported • EDD/SIMATIC PDM: Improved rendering of the echo profile and TVT 1.01.01 1.01.01 10 Jun 2008 • Maintenance release of firmware and EDD a) 1.01.01 1.01.03 17 Jun 2008 • The internal EDD revision has been incremented 1.02.01 1.02.01 2 Apr 2009 • AMS EDD Rev. 1.02.01 • Support NAMUR NE 43 • Harmonization of menu structures and parameter names across products • Display indicates progress towards first measurement • Display contrast improvement • Antenna type parameter cannot be modified 1.02.03 1.02.01 16 June 2010 1.03.02 (requires HW 2.0.0) 1.02.01 16 June 2010 • Low current HW 2.0.0 supported 1.03.03 (requires HW 2.0.0) 1.02.01 19 May 2011 • Threaded PVDF antenna supported 1.03.04 1.02.03 31 Oct 2012 • LUI updated version (new startup, progress bars, quick start updated to latest version, echo profile pan/zoom on display) • antenna parameter removed, default near range set at factory a) Electronic Device Description b) See Sensor Mode (2.2.2.) for an illustration of Distance. SITRANS LR250 (mA/HART) 10 Operating Instructions, 08/2014, A5E32220602-AC Introduction 1.5 Designated use 1.5 Designated use Use the device to measure process media in accordance with the information in the operating instructions. Note Use in a domestic environment This is a Class A Group 1 equipment intended for use in industrial areas. In a domestic environment this device may cause radio interference. 1.6 Checking the consignment 1. Check the packaging and the device for visible damage caused by inappropriate handling during shipping. 2. Report any claims for damages immediately to the shipping company. 3. Retain damaged parts for clarification. 4. Check the scope of delivery by comparing your order to the shipping documents for correctness and completeness. WARNING Using a damaged or incomplete device Danger of explosion in hazardous areas. • Do not use damaged or incomplete devices. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 11 Introduction 1.7 Transportation and storage 1.7 Transportation and storage To guarantee sufficient protection during transport and storage, observe the following: ● Keep the original packaging for subsequent transportation. ● Devices/replacement parts should be returned in their original packaging. ● If the original packaging is no longer available, ensure that all shipments are properly packaged to provide sufficient protection during transport. Siemens cannot assume liability for any costs associated with transportation damages. CAUTION Insufficient protection during storage The packaging only provides limited protection against moisture and infiltration. • Provide additional packaging as necessary. 1.8 Notes on warranty The contents of this manual shall not become part of or modify any prior or existing agreement, commitment or legal relationship. The sales contract contains all obligations on the part of Siemens as well as the complete and solely applicable warranty conditions. Any statements regarding device versions described in the manual do not create new warranties or modify the existing warranty. The content reflects the technical status at the time of publishing. Siemens reserves the right to make technical changes in the course of further development. SITRANS LR250 (mA/HART) 12 Operating Instructions, 08/2014, A5E32220602-AC 2 Safety information 2.1 Preconditions for safe use This device left the factory in good working condition. In order to maintain this status and to ensure safe operation of the device, observe these instructions and all the specifications relevant to safety. Observe the information and symbols on the device. Do not remove any information or symbols from the device. Always keep the information and symbols in a completely legible state. 2.1.1 Safety marking symbols In manual On product Description WARNING: refer to accompanying documents (manual) for details. (Label on product: yellow background.) 2.1.2 Laws and directives Observe the test certification, provisions and laws applicable in your country during connection, assembly and operation. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 13 Safety information 2.1 Preconditions for safe use 2.1.3 FCC Conformity US Installations only: Federal Communications Commission (FCC) rules WARNING Improper device modifications Danger to personnel, system and environment can result from improper modifications to the device. • Changes or modifications not expressly approved by Siemens could void the user’s authority to operate the equipment. Note • This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. • This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operating instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference to radio communications, in which case the user will be required to correct the interference at his own expense. SITRANS LR250 (mA/HART) 14 Operating Instructions, 08/2014, A5E32220602-AC Safety information 2.1 Preconditions for safe use 2.1.4 Conformity with European directives The CE marking on the device symbolizes the conformity with the following European directives: Electromagnetic compatibility EMC 2004/108/EC Directive of the European Parliament and of the Council on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC. Low voltage directive LVD 2006/95/EC Directive of the European Parliament and of the Council on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits. Atmosphère explosible ATEX 94/9/EC Directive of the European Parliament and the Council on the approximation of the laws of the Member States concerning equipment and protective systems intended for use in potentially explosive atmospheres. Radio and Directive of the European Parliament and of the Council on telecommunications terminal radio equipment and telecommunications terminal equipment equipment R&TTE and the mutual recognition of their conformity. 1999/5/EC The applicable directives can be found in the EC conformity declaration of the specific device. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 15 Safety information 2.2 Improper device modifications 2.1.5 CE Electromagnetic Compatibility (EMC) Conformity This equipment has been tested and found to comply with the following EMC Standards: 2.2 EMC Standard Title CISPR 11:2009 + A1:2010/EN 55011:2009 + A1:2010, CLASS A Limits and methods of measurements of radio disturbance characteristics of industrial, scientific, and medical (ISM) radio-frequency equipment. EN 61326:2013 (IEC 61326:2012) Electrical Equipment for Measurement, Control and Laboratory Use – Electromagnetic Compatibility. EN61000-4-2:2009 Electromagnetic Compatibility (EMC) Part 4-2: Testing and measurement techniques – Electrostatic discharge immunity test. EN61000-4-3:2006 + A1:2008 + A2:2010 Electromagnetic Compatibility (EMC) Part 4-3: Testing and measurement techniques – Radiated, radio-frequency, electromagnetic field immunity test 2006 + A1:2008 + A2:2010. EN61000-4-4:2004 + A1:2010 Electromagnetic Compatibility (EMC) Part 4-4: Testing and measurement techniques – Electrical fast transient/burst immunity test. EN61000-4-5:2006 Electromagnetic Compatibility (EMC) Part 4-5: Testing and measurement techniques – Surge immunity test. EN61000-4-6:2010 Electromagnetic Compatibility (EMC) Part 4-6: Testing and measurement techniques – Immunity to conducted disturbances, induced by radio-frequency fields. EN61000-4-8:2010 Electromagnetic Compatibility (EMC) Part 4-8: Testing and measurement techniques – Power frequency magnetic field immunity test. Improper device modifications WARNING Improper device modifications Danger to personnel, system and environment can result from modifications to the device, particularly in hazardous areas. • Only carry out modifications that are described in the instructions for the device. Failure to observe this requirement cancels the manufacturer's warranty and the product approvals. SITRANS LR250 (mA/HART) 16 Operating Instructions, 08/2014, A5E32220602-AC Safety information 2.3 Requirements for special applications 2.3 Requirements for special applications Due to the large number of possible applications, each detail of the described device versions for each possible scenario during commissioning, operation, maintenance or operation in systems cannot be considered in the instructions. If you need additional information not covered by these instructions, contact your local Siemens office or company representative. Note Operation under special ambient conditions We highly recommend that you contact your Siemens representative or our application department before you operate the device under special ambient conditions as can be encountered in nuclear power plants or when the device is used for research and development purposes. 2.4 Use in hazardous areas Qualified personnel for hazardous area applications Persons who install, connect, commission, operate, and service the device in a hazardous area must have the following specific qualifications: ● They are authorized, trained or instructed in operating and maintaining devices and systems according to the safety regulations for electrical circuits, high pressures, aggressive, and hazardous media. ● They are authorized, trained, or instructed in carrying out work on electrical circuits for hazardous systems. ● They are trained or instructed in maintenance and use of appropriate safety equipment according to the pertinent safety regulations. WARNING Loss of safety of device with type of protection "Intrinsic safety Ex i" If the device has already been operated in non-intrinsically safe circuits or the electrical specifications have not been observed, the safety of the device is no longer ensured for use in hazardous areas. There is a danger of explosion. • Connect the device with type of protection "Intrinsic safety" solely to an intrinsically safe circuit. • Observe the specifications for the electrical data on the certificate. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 17 Safety information 2.4 Use in hazardous areas SITRANS LR250 (mA/HART) 18 Operating Instructions, 08/2014, A5E32220602-AC 3 Description 3.1 SITRANS LR250 overview WARNING Loss of protection Danger to personnel, system and environment can result from improper use of the device. • SITRANS LR250 is to be used only in the manner outlined in this manual, otherwise protection provided by the device may be impaired. SITRANS LR250 is a 2-wire 25 GHz pulse radar level transmitter for continuous monitoring of liquids and slurries in storage vessels including high pressure and high temperature, to a range of 20 meters (66 feet). It is ideal for small vessels, material such as chemicals, food, beverages, solvents (including those of corrosive or aggressive nature), and low dielectric media. The device consists of an electronic circuit coupled to an antenna and either a threaded or flange type process connection. This device supports HART communication protocol. Signals are processed using Process Intelligence which has been field-proven in over 1,000,000 applications worldwide (ultrasonic and radar). SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 19 Description 3.2 Programming 3.2 Programming This device is very easy to install and configure via a graphical local user interface (LUI). You can modify the built in parameters either locally via the Siemens infrared handheld programmer, or from a remote location using one of the following options: ● SIMATIC PDM ● AMS Device Manager ● FDT/DTM platform (such as PACTware™ or FieldCare) ● HART Handheld 375/475 3.3 Applications ● liquids and slurries ● bulk storage vessels ● simple process vessels ● corrosive and aggressive ● hygienic/sanitary 3.4 Approvals and certificates Note For further details see Approvals (Page 206). SITRANS LR250 is available with approvals for General purpose, sanitary or hygienic and for hazardous areas. In all cases, check the nameplate on your device, and confirm the approval rating. Process Connections A wide range of process connections and antenna options are available to suit virtually any vessel configuration. SITRANS LR250 (mA/HART) 20 Operating Instructions, 08/2014, A5E32220602-AC Installing/mounting 4.1 Basic safety information Note Material compatibility Siemens can provide you with support concerning selection of sensor components wetted by process media. However, you are responsible for the selection of components. Siemens accepts no liability for faults or failures resulting from incompatible materials. WARNING Unsuitable connecting parts Danger of injury or poisoning. In case of improper mounting hot, toxic and corrosive process media could be released at the connections. • Ensure that connecting parts (such as flange gaskets and bolts) are suitable for connection and process media. WARNING Exceeded maximum ambient or process media temperature Danger of explosion in hazardous areas. Device damage. • Make sure that the maximum permissible ambient and process media temperatures of the device are not exceeded. WARNING Open cable inlet or incorrect cable gland Danger of explosion in hazardous areas. • Close the cable inlets for the electrical connections. Only use cable glands or plugs which are approved for the relevant type of protection. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 21 Installing/mounting 4.1 Basic safety information WARNING Incorrect conduit system Danger of explosion in hazardous areas as result of open cable inlet or incorrect conduit system. • In the case of a conduit system, mount a spark barrier at a defined distance from the device input. Observe national regulations and the requirements stated in the relevant approvals. 4.1.1 Pressure applications DANGER Pressure applications Danger to personnel, system and environment will result from improper disassembly. • Never attempt to loosen, remove, or disassemble process connection while vessel contents are under pressure. WARNING Pressure applications Danger to personnel, system and environment can result from improper installation. • Improper installation may result in loss of process pressure. WARNING Exceeded maximum permissible operating pressure Danger of injury or poisoning. The maximum permissible operating pressure depends on the device version. The device can be damaged if the operating pressure is exceeded. Hot, toxic and corrosive process media could be released. • Make sure that the device is suitable for the maximum permissible operating pressure of your system. SITRANS LR250 (mA/HART) 22 Operating Instructions, 08/2014, A5E32220602-AC Installing/mounting 4.1 Basic safety information Note • The process connection tag shall remain with the process pressure boundary assembly. (The process pressure boundary assembly comprises the components that act as a barrier against pressure loss from the process vessel: that is, the combination of process connection body and emitter, but normally excluding the electrical enclosure). In the event the device package is replaced, the process connection tag shall be transferred to the replacement unit. • SITRANS LR250 units are hydrostatically tested, meeting or exceeding the requirement of the ASME Boiler and Pressure Vessel Code and the European Pressure Equipment Directive. Note • The serial numbers stamped in each process connection body, (flange, threaded, or sanitary), provide a unique identification number indicating date of manufacture. Example: MMDDYY – XXX (where MM = month, DD = day, YY = year, and XXX= sequential unit produced) • Further markings (space permitting) indicate flange configuration, size, pressure class, material, and material heat code. 4.1.1.1 Pressure Equipment Directive, PED, 97/23/EC Siemens Level Transmitters with flanged, threaded, or sanitary clamp type process mounts have no pressure-bearing housing of their own and, therefore, do not come under the Pressure Equipment Directive as pressure or safety accessories (see EU Commission Guideline 1/8 and 1/20). SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 23 Installing/mounting 4.2 Installation location requirements 4.2 Installation location requirements WARNING Aggressive atmospheres Danger to personnel, system and environment can result from unsuitable environment. • Provide an environment suitable to the housing rating and materials of construction. CAUTION Direct sunlight Device damage. The device can overheat or materials become brittle due to UV exposure. • Protect the device from direct sunlight. • Make sure that the maximum permissible ambient temperature is not exceeded. Refer to the information in Chapter "Technical data (Page 199)". SITRANS LR250 (mA/HART) 24 Operating Instructions, 08/2014, A5E32220602-AC Installing/mounting 4.2 Installation location requirements ① ② ③ ④ ⑤ Ambient temperature Device nameplate Device tag Process temperature (at process connection) Process connection tag (contains process connection related information) Antenna Horn ① -40 to +80 °C (-40 to +176 °F) ③ with FKM O-ring:-40 to +200 °C (-40 to 392 °F) with FFKM O-ring:-20 to +200 °C (-4 to +392 °F) PVDF -40 to +80 °C (-40 to +176 °F) -40 to +80 °C (-40 to +176 °F) Flanged encapsulated -40 to +80 °C (-40 to +176 °F) -40 to +170 °C (-40 to +338 °F) Hygienic encapsulated -40 to +80 °C (-40 to +176 °F) -40 to +170 °C (-40 to +338 °F) with FKM seals used on process connection: -20 to +170 °C (-4 to +338 °F) with EPDM seals used on process connection: -40 to +120 °C (-40 to +248 °F) Note Details about the process connection, process temperature and materials are laser etched into the body of the flanged and hygienic versions. All other SITRANS LR250 versions have details listed on a tag. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 25 Installing/mounting 4.3 Proper mounting 4.3 Proper mounting Note • Correct location is key to a successful application. • Avoid reflective interference from vessel walls and obstructions by following guidelines in this chapter. NOTICE Incorrect mounting The device can be damaged, destroyed, or its functionality impaired through improper mounting. • Before installing ensure there is no visible damage to the device. • Make sure that process connectors are clean, and suitable gaskets and glands are used. • Mount the device using suitable tools. Refer to the information in Installation instructions (Page 34) for installation torque requirements. Note • On devices with a removable head, there is no limit to the number of times a device can be rotated without damage. • When mounting, orient the front or back of the device towards the closest vessel wall or obstruction. • Do not rotate the enclosure after programming and vessel calibration, otherwise an error may occur, caused by a polarity shift of the transmit pulse. SITRANS LR250 (mA/HART) 26 Operating Instructions, 08/2014, A5E32220602-AC Installing/mounting 4.3 Proper mounting 4.3.1 Nozzle design Threaded PVDF antenna Stainless steel horn antenna Flanged encapsulated antenna (FEA) Hygienic encapsulated antenna (HEA) ① ② ③ ④ Minimum clearance: 10 mm (0.4") Minimum diameter: 50 mm (2") Maximum nozzle length Maximum length/diameter ratio 1:1 ● The end of the antenna must protrude a minimum of 10 mm (0.4") to avoid false echoes being reflected from the nozzle1). ● Minimum recommended nozzle diameter for the threaded PVDF antenna is 50 mm (2"). ● An antenna extension (100 mm/3.93") is available for the horn antenna only. ● The maximum nozzle length for the FEA is 500 mm (19.68") when the nozzle diameter is DN150 (6"). Only shorter lengths are recommended for smaller diameters. ● When installing the SITRANS LR250 with hygienic process connection, it is good hygienic practice to install the antenna in a nozzle that has a maximum length/diameter ratio of 1:1. For example, 2" (DN50) diameter nozzle should be no longer than 2" (50 mm). ● When removing any sanitary/hygienic clamp version of the HEA to clean the lens, ensure it is re-installed in the exact position it was removed from, to avoid re-commissioning the device. 1) Not applicable for FEA or HEA SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 27 Installing/mounting 4.3 Proper mounting 4.3.2 Nozzle location ● Avoid central locations on tall, narrow vessels ● Nozzle must be vertical and clear of imperfections Preferred Undesirable Beam angle Note • Beam width depends on antenna size and is approximate: see below. • For details on avoiding false echoes, see Auto False Echo Suppression (Page 259). ● Beam angle is the width of the cone where the energy density is half of the peak energy density. ● The peak energy density is directly in front of and in line with the antenna. ● There is a signal transmitted outside the beam angle, therefore false targets may be detected. SITRANS LR250 (mA/HART) 28 Operating Instructions, 08/2014, A5E32220602-AC Installing/mounting 4.3 Proper mounting Horn antenna Flanged encapsulated antenna Threaded PVDF antenna Hygienic encapsulated antenna ① ② Emission cone Beam angle SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 29 Installing/mounting 4.3 Proper mounting Emission cone type and beam angle Antenna type Antenna size Beam angle Horn 1.5" 19° 2" 15° 3" 10° 4" 8° Threaded PVDF Flanged encapsulated Hygienic encapsulated 19° Process connection size Process connection type 2" Class 150 ASME B16.5 12.8° 3, 4, 6" Class 150 ASME B16.5 9.6° 50A 10K JIS B 2220 12.8° 80A/100A/150A 10K JIS B 2220 9.6° DN50 PN10/16 EN1092-1 12.8° DN80/DN100/DN15 PN10/16 EN1092-1 9.6° 2" 12.8° 3, 4" DN50 DN80/DN100 DN50 DN80/DN100 DN50 DN80/DN100 DN50 DN80/DN100 Type F (50 mm) and Type N (68 mm) Sanitary Clamp according to ISO 2852 9.6° Aseptic/Hygienic nozzle/slotted 12.8° nut according to DIN 11864-1 9.6° [Form A] Aseptic/Hygienic flanged according to DIN 11864-2 [Form A] 12.8° Aseptic/Hygienic Clamp according to DIN 118643 [Form A] 12.8° Hygienic nozzle/slotted nut according to DIN 11851 12.8° Tuchenhagen Varivent 12.8° 9.6° 9.6° 9.6° Emission cone ● Keep emission cone free of interference from obstructions such as ladders, pipes, I-beams, or filling streams. Access for programming ● Provide easy access for viewing the display and programming via the handheld programmer. SITRANS LR250 (mA/HART) 30 Operating Instructions, 08/2014, A5E32220602-AC Installing/mounting 4.3 Proper mounting 4.3.3 Orientation in a vessel with obstructions Polarization reference point For best results on a vessel with obstructions, or a stillpipe with openings, orient the front or back of the device toward the obstructions. For an illustration, see Device orientation (Page 33). ① ② ③ Polarization axis Polarization reference point Display SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 31 Installing/mounting 4.3 Proper mounting 4.3.4 Mounting on a Stillpipe or Bypass Pipe A stillpipe or bypass pipe is used for products with a low dK, or when vortex or extremely turbulent conditions exist. It can also be used to provide optimum signal conditions on foaming materials. See Dielectric constant of material measured in Performance (Page 199) for more information. ● The pipe diameter must be matched with the antenna size. Use the largest antenna size that will fit the stillpipe/bypass pipe1). See Threaded Horn dimensions, Raised-Face Flange per EN 1092-1 (Page 243), Flanged encapsulated dimensions (Page 218)or Hygienic encapsulated dimensions (Page 222). ● One continuous length of metallic pipe is preferred, without joints. ● Any false reflections created by joints/welds/imperfections will lead to inaccuracies of the measurement. ● Joints (if unavoidable) must be machined to ± 0.25 mm (± 0.010") and must have welded connecting sleeve on the outside. ● If using any hygienic process connections in conjunction with a stillpipe/bypass, please ensure that the antenna/lens are cleanable in accordance with the applicable approval. 1) Mounting in a pipe greater than 100 mm (4") can cause large errors, and therefore is not recommended. Suitable pipe diameters: Horn antenna 40 to 100 mm (1.5 to 4") PVDF antenna 50 mm (2") only Flanged encapsulated antenna 50 to 100 mm (2 to 4") Hygienic encapsulated antenna 50 to 100 mm (2 to 4") Not recommended: > 100 mm (4") Bypass vent: Required at the upper end of the bypass 1) 1) To equalize pressure and keep the liquid level in the bypass constant with the liquid level in the vessel. SITRANS LR250 (mA/HART) 32 Operating Instructions, 08/2014, A5E32220602-AC Installing/mounting 4.3 Proper mounting 4.3.5 Device orientation Bypass pipe installation Stillpipe installation ① Vent ① Align front or back of device with stillpipe slots1) ② Align front or back of device with ② Slots vents1) 1) Horn antenna version shown as example SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 33 Installing/mounting 4.4 Installation instructions 4.4 Installation instructions WARNING Pressure applications Danger to personnel, system and environment can result from improper installation. • Improper installation may result in loss of process pressure. WARNING Improper installation Danger to personnel, system and environment can result from improper installation. • Installation shall only be performed by qualified personnel and in accordance with local governing regulations. NOTICE Device handling Damage to device may result from improper handling. • Handle the device using the enclosure, not the process connection or tag, to avoid damage. • Take special care when handling the threaded PVDF and Hygienic or Flanged encapsulated antennas. Any damage to the antenna surface, particularly to the tip/lens, could affect performance. (For example, do not sit device on its lens antenna.) Note • For European Union and member countries, installation must be according to ETSI EN 302372. • Refer to the device nameplate for approval information. Note The outer part of the lens on the flanged encapsulated antenna version may not appear to lie flush before installation and this is normal. This will flatten after installation and will not impact the performance of the device. SITRANS LR250 (mA/HART) 34 Operating Instructions, 08/2014, A5E32220602-AC Installing/mounting 4.4 Installation instructions 4.4.1 Threaded versions WARNING Pressure applications Danger of injury or poisoning. It may be necessary to use PTFE tape or other appropriate thread sealing compound, and to tighten the process connection beyond hand-tight. (The maximum recommended torque for Threaded versions is 40 N-m (30 ft.lbs.) 1. Before inserting the device into its mounting connection, check to ensure the threads are matching, to avoid damaging them. 2. Simply screw the device into the process connection, and hand tighten, or use a wrench. 4.4.2 Flanged versions NOTICE Improper materials The user is responsible for the selection of bolting and gasket materials (except for Flanged encapsulated antenna) which will fall within the limits of the process connection and its intended use, and which are suitable for the service conditions. Special Instructions for Flanged encapsulated antenna only Note • Use spring washers • Lens assembly acts as integral gasket, no other required • Use recommended torque values for tightening bolts SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 35 Installing/mounting 4.4 Installation instructions Flange bolting: recommended torque Pressure class ASME B16.5, Class 150 Nominal pipe size (NPS) 2" Number of bolts 3" 4" Recommended torque (Nm) 30 – 50 50 – 70 6" 40 – 60 70 – 90 EN1092-1, PN16 / DN50/50A JIS B 2220, 10K DN80/80A 30 – 50 DN100/100A DN150/150A 60 – 80 SITRANS LR250 (mA/HART) 36 Operating Instructions, 08/2014, A5E32220602-AC Installing/mounting 4.4 Installation instructions Flange bolting instructions: 1. Use cross-pattern sequence as shown. 2. Check uniformity of the flange gap. 3. Apply adjustments by selective tightening if required. 4. Torque incrementally until desired value is reached. 5. Check/re-torque after 4 to 6 hours. Recommendations for flange bolting: ● Check bolts periodically, re-torque as required. ● Use new lens, O-ring and spring washers after removal from installation. For instructions on replacing the lens, see Part replacement (Page 185). See Flanged Horn with extension (Page 214), Raised-Face Flange per EN 1092-1 (Page 243), Flat-Face Flange (Page 246), and Flanged encapsulated antenna (3"/DN80/80A sizes and larger) (Page 220) for dimensions. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 37 Installing/mounting 4.4 Installation instructions 4.4.3 Hygienic versions WARNING Loss of sanitary approvals Loss of sanitary approvals can result from improper installation/mounting. • Take special care when installing in hygienic or sanitary applications. Comply with installation/mounting guidelines to ensure cleanliness and the ability to keep the wetted parts in a position to be readily cleanable. (See relevant EHEDG/3A documentation - not supplied). NOTICE Loss of sanitary approvals • For 3-A Sanitary Approved device installation where the customer tank process connection exists, a leak detection port of minimum 2.4 mm diameter must be provided at the lowest point in the process connection where leakage can occur. • If leakage is detected at any time while the device is installed, then the device process connection parts must be disassembled and thoroughly cleaned prior to gasket replacement and reassembly. Note • For Hygienic encapsulated antenna, the lens acts as a gasket/seal and should be used in conjunction with a cleanable seal as required by the specific process connections (for example, DIN 11864-3). Hygienic encapsulated antenna leak detection port ① ② Orientation mark for leak detection port Leak detection port SITRANS LR250 (mA/HART) 38 Operating Instructions, 08/2014, A5E32220602-AC Installing/mounting 4.5 Disassembly 4.5 Disassembly DANGER Pressure applications Danger to personnel, system and environment will result from improper disassembly. • Never attempt to loosen, remove, or disassemble process connection while vessel contents are under pressure. WARNING Incorrect disassembly The following dangers may result through incorrect disassembly: - Injury through electric shock - Danger through emerging media when connected to the process - Danger of explosion in hazardous area In order to disassemble correctly, observe the following: • Before starting work, make sure that you have switched off all physical variables such as pressure, temperature, electricity etc. or that they have a harmless value. • If the device contains dangerous media, it must be emptied prior to disassembly. Make sure that no environmentally hazardous media are released. • Secure the remaining connections so that no damage can result if the process is started unintentionally. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 39 Installing/mounting 4.5 Disassembly SITRANS LR250 (mA/HART) 40 Operating Instructions, 08/2014, A5E32220602-AC 5 Connecting 5.1 Basic safety information NOTICE Condensation in the device Damage to device through formation of condensation if the temperature difference between transportation or storage and the mounting location exceeds 20 °C (68°F). • Before taking the device into operation let the device adapt for several hours in the new environment. WARNING Missing PE/ground connection Danger of electric shock. Depending on the device version, connect the power supply as follows: • Power plug: Ensure that the used socket has a PE/ground conductor connection. Check that the PE/ground conductor connection of the socket and power plug match each other. • Connecting terminals: Connect the terminals according to the terminal connection diagram. First connect the PE/ground conductor. 5.2 Connecting SITRANS LR250 WARNING Incorrect connection to power source Danger to personnel, system and environment can result from improper power connection. • The DC input terminals shall be supplied from a source providing electrical isolation between the input and output, in order to meet the applicable safety requirements of IEC 61010-1. • All field wiring must have insulation suitable for rated voltages. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 41 Connecting 5.2 Connecting SITRANS LR250 WARNING Loss of protection Loss of approvals can result from improper installation. • Check the nameplate on your device, to verify the approval rating. • Use appropriate conduit seals to maintain IP or NEMA rating. • See Wiring setups for hazardous area installations (Page 45). NOTICE Improper cables and conduit • Separate cables and conduits may be required to conform to standard instrumentation wiring practices or electrical codes. SITRANS LR250 (mA/HART) 42 Operating Instructions, 08/2014, A5E32220602-AC Connecting 5.2 Connecting SITRANS LR250 ① ② ③ a) Use a 2 mm Allen key to loosen the lid-lock set screw c) Plug (IP68) ④ ⑤ Cable shield Ground terminal Optional cable gland a) b) (or NPT cable entry)b) May be shipped with the device. If cable is routed through conduit, use only approved suitable-size hubs for waterproof applications. b) c) Not applicable to 3-A Sanitary approved device. Wiring instructions 1. Strip the cable jacket for approximately 70 mm (2.75") from the end of the cable, and thread the wires through the gland. (If cable is routed through conduit, use only approved suitablesize hubs for waterproof applications.) 2. Connect the wires to the terminals as shown: the polarity is identified on the terminal block. 3. Ground the device according to local regulations. 4. Tighten the gland to form a good seal. 5. Close the lid and secure the locking screw before programming and device configuration. Note Lid-lock set screw not applicable to 3-A Sanitary approved device. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 43 Connecting 5.2 Connecting SITRANS LR250 Connecting HART Typical PLC/mA configuration with HART ① ② ③ Power supply SITRANS LR250 R = 250 Ω ④ ⑤ ⑥ Active PLC HART modem HART communicator Note • Depending on the system design, the power supply may be separate from the PLC, or integral to it. • HART resistance (total loop resistance, that is, cable resistance plus 250 Ohm [resistor]) must be limited according to the allowable operating area as shown in either Curve 1 (Page 282) (General Purpose, Intrinsically Safe, Non-Sparking, Non-incendive) or Curve 2 (Page 283) (Flameproof, Increased Safety, Explosion-proof). SITRANS LR250 (mA/HART) 44 Operating Instructions, 08/2014, A5E32220602-AC Connecting 5.3 Wiring setups for hazardous area installations 5.3 Wiring setups for hazardous area installations There are six wiring options for hazardous area installations: ● Intrinsically Safe wiring (Page 45) ● Non-Sparking wiring (Page 47) ● Non-incendive wiring (US/Canada only) (Page 47) ● Flameproof wiring (Page 48) ● Increased safety wiring (Page 49) ● Explosion-proof wiring (US/Canada only) (Page 49) In all cases, check the nameplate on your instrument, confirm the approval rating, and perform installation and wiring according to your local safety codes. 5.3.1 Intrinsically safe wiring Device nameplate (ATEX/IECEX/INMETRO/RCM) ① ATEX certificate The ATEX certificate listed on the nameplate can be downloaded from our website: Product page (http://www.siemens.com/LR250) Go to Support > Approvals / Certificates. The IECEx certificate listed on the nameplate can be viewed on the IECEx website. Go to: IECEx (http://iecex.iec.ch/) Click on Certified Equipment then enter the certificate number IECEx SIR 05.0031X. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 45 Connecting 5.3 Wiring setups for hazardous area installations Device nameplate (FM/CSA) The connection drawing number listed on the nameplate can be downloaded from our website: Product page (http://www.siemens.com/LR250) Go to Support > Installation Drawings > Level Measurement > SITRANS LR250. ● For power demands see Curve 1 (General Purpose, Intrinsically Safe, Non-Sparking, Nonincendive) (Page 282). ● For wiring requirements: follow local regulations. ● Approved dust-tight and water-tight conduit seals are required for outdoor NEMA 4X / type 4X / NEMA 6, IP67, IP68 locations. ● Refer to Instructions specific to hazardous area installations (Page 50). Note Selecting a suitable PLC input module or power supply requires knowledge about Intrinsic Safety and the application. It is the responsibility of the installer to ensure that the intrinsically safe installation complies with both the apparatus approval requirements and the relevant national code of practice. SITRANS LR250 (mA/HART) 46 Operating Instructions, 08/2014, A5E32220602-AC Connecting 5.3 Wiring setups for hazardous area installations 5.3.2 Non-sparking wiring ① ATEX certificate The ATEX certificate listed on the nameplate can be downloaded from our website: Product page (http://www.siemens.com/LR250) Go to: Support > Approvals / Certificates. ● For power demands see Curve 1 (General Purpose, Intrinsically Safe, Non-Sparking/Energy Limited, Non-incendive) (Page 282). ● For wiring requirements follow local regulations. 5.3.3 Non-incendive wiring (US/Canada only) The FM/CSA Class 1, Div 2 connection drawing number 23650673 can be downloaded from our website: Product page (http://www.siemens.com/LR250) Go to Support > Installation Drawings > Level Measurement > SITRANS LR250. ● For power demands see Curve 1 (General Purpose, Intrinsically Safe, Non-Sparking, Nonincendive) (Page 282). SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 47 Connecting 5.3 Wiring setups for hazardous area installations 5.3.4 Flameproof wiring ① ATEX certificate The ATEX certificate listed on the nameplate can be downloaded from our website: Product page (http://www.siemens.com/LR250) Go to Support > Approvals / Certificates. The IECEx certificate listed on the nameplate can be viewed on the IECEx website. Go to: IECEx (http://iecex.iec.ch/) Click on Certified Equipment then enter the certificate number IECEx SIR 08.0107X. ● For power demands see Curve 2 (Flameproof, Increased Safety, Explosion-proof) (Page 283). ● For wiring requirements follow local regulations. ● See also Instructions specific to hazardous area installations (Page 50) and the ATEX certificate listed above. SITRANS LR250 (mA/HART) 48 Operating Instructions, 08/2014, A5E32220602-AC Connecting 5.3 Wiring setups for hazardous area installations 5.3.5 Increased safety wiring ① ATEX certificate The ATEX certificate listed on the nameplate can be downloaded from our website: Product page (http://www.siemens.com/LR250) Go to Support > Approvals / Certificates. The IECEx certificate listed on the nameplate can be viewed on the IECEx website: IECEx (http://iecex.iec.ch/) Click on Certified Equipment then enter the certificate number IECEx SIR 08.0107X. ● For power demands see Curve 2 (Flameproof, Increased Safety, Explosion-proof) (Page 283). ● For wiring requirements follow local regulations. ● See also Instructions specific to hazardous area installations (Page 50) and the ATEX certificate listed above. 5.3.6 Explosion-proof wiring (US/Canada only) ① FM/CSA Explosion Proof connection drawing The connection drawing number listed on the nameplate can be downloaded from our website: Product page (http://www.siemens.com/LR250) Go to Support > Installation Drawings > Level Measurement > SITRANS LR250 ● For power demands see Curve 2 (Flameproof, Increased Safety, Explosion-proof) (Page 283). SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 49 Connecting 5.4 Instructions specific to hazardous area installations 5.4 Instructions specific to hazardous area installations 5.4.1 (Reference European ATEX Directive 94/9/EC, Annex II, 1/0/6) The following instructions apply to equipment covered by certificate number SIRA 06ATEX2358X, SIRA 08ATEX1301X, and SIRA 09ATEX4153X. 1. For use and assembly, refer to the main instructions. 2. The equipment is certified for use as Category 1GD equipment per SIRA 06ATEX2358X; Category 1/2 GD, 1D, 2D equipment per SIRA 08ATEX1301X; and Category 3G equipment per SIRA 09ATEX4153X. 3. The equipment may be used with flammable gases and vapors with apparatus group IIC, IIB and IIA and temperature classes T1, T2, T3 and T4. 4. The equipment has a degree of ingress protection of IP67 and a temperature class of T100 °C and may be used with flammable dusts. 5. The equipment is certified for use in an ambient temperature range of –40 °C to +80 °C. 6. The equipment has not been assessed as a safety related device (as referred to by Directive 94/9/EC Annex II, clause 1.5). 7. Installation and inspection of this equipment shall be carried out by suitably trained personnel in accordance with the applicable code of practice (EN 60079-14 and EN 60079-17 in Europe). 8. The equipment is non-repairable. 9. The certificate numbers have an ‘X’ suffix, which indicates that special conditions for safe use apply. Those installing or inspecting this equipment must have access to the certificates. 10.If the equipment is likely to come into contact with aggressive substances, then it is the responsibility of the user to take suitable precautions that prevent it from being adversely affected, thus ensuring that the type of protection is not compromised. – Aggressive substances: for example, acidic liquids or gases that may attack metals, or solvents that may affect polymeric materials. – Suitable precautions: for example, establishing from the material’s data sheet that it is resistant to specific chemicals. SITRANS LR250 (mA/HART) 50 Operating Instructions, 08/2014, A5E32220602-AC Connecting 5.4 Instructions specific to hazardous area installations Special conditions for safe use (denoted by X after the certificate number) ● Parts of the enclosure may be non-conducting and may generate an ignition-capable level of electrostatic charge under certain extreme conditions. The user should ensure that the equipment is not installed in a location where it may be subjected to external conditions (such as high-pressure steam), which might cause a build-up of electrostatic charge on nonconducting surfaces. ● Aluminium, magnesium, titanium or zirconium may be used at the accessible surface of the equipment. In the event of rare incidents, ignition sources due to impact and friction sparks could occur. This shall be considered when the SITRANS LR250 mA/HART is being installed in locations that specifically require group II, level of protection Ga or Da. ● The equipment shall be bonded to the system earth in accordance with the relevant code of practice. ● When the SITRANS LR250 mA/HART is used in the presence of combustible dust, the gland that is fitted to the equipment shall also be suitable for use in the presence of combustible dust, as certified by an ATEX notified body, in addition, the installation of the gland shall not compromise the IP6X rating of the equipment enclosure. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 51 Connecting 5.4 Instructions specific to hazardous area installations SITRANS LR250 (mA/HART) 52 Operating Instructions, 08/2014, A5E32220602-AC Commissioning 6.1 Basic safety information WARNING Loss of explosion protection Danger of explosion when device is not properly commissioned If opening device • Isolate from power. - or • Ensure that the atmosphere is explosion-free (hot work permit). Ensure device is properly closed before returning to operation. 6.2 Operating via the handheld programmer The handheld programmer used with this device contains lithium batteries that are nonreplaceable. Lithium batteries are primary power sources with high energy content designed to represent the highest possible degree of safety. WARNING Potential hazard Lithium batteries may present a potential hazard if they are abused electrically or mechanically. • Observe the following precautions when handling and using lithium batteries: – Do not short-circuit, recharge or connect with false polarity. – Do not expose to temperature beyond the specified temperature range or incinerate the battery. – Do not crush, puncture or open cells or disassemble battery packs. – Do not weld or solder to the battery’s body. – Do not expose contents to water. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 53 Commissioning 6.2 Operating via the handheld programmer 6.2.1 Power up Power up the device. A transition screen showing first the Siemens logo and then the current firmware revision is displayed while the first measurement is being processed. The first time the device is configured, you will be prompted to select a language (English, German, French, or Spanish). To change the language again, see Language (7.). Press Mode 6.2.2 to toggle between Measurement and Program mode. Handheld programmer functions The radar device carries out its level measurement tasks according to settings made via parameters. The settings can be modified locally via the Local User Interface (LUI) which consists of an LCD display and a handheld programmer. A Quick Start Wizard provides an easy step-by-step procedure to configure the device for a simple application. Access the wizards: ● locally [see Quick Start Wizard via the handheld programmer (Page 64)] ● or from a remote location [see Quick Start Wizard via SIMATIC PDM (Page 81), or Quick Start Wizard via AMS Device Manager (Page 107)] For more complex setups see Application Examples (Page 70), and for the complete range of parameters see Parameter Reference (Page 127). SITRANS LR250 (mA/HART) 54 Operating Instructions, 08/2014, A5E32220602-AC Commissioning 6.2 Operating via the handheld programmer 6.2.2.1 The LCD display Measurement mode display Normal operation ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ a) Toggle indicator a) for linear units or % Selected operation: level, space, distance, or volume Measured value (level, space, distance, or volume) Units Bar graph indicates level Secondary region indicates on request b) electronics temperature, echo confidence, loop current, or distance Text area displays status messages Device status indicator, see Device status icons (Page 190) Press UP or DOWN arrow to switch. In response to a key press request. For details, see Handheld Programmer (Page 57) for key functions in Measurement mode. b) Fault present ① ② Device status indicator, see Device status icons (Page 190) Text area displays status messages SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 55 Commissioning 6.2 Operating via the handheld programmer PROGRAM mode display Navigation view ① ② ③ Item band Menu bar ④ ⑤ Current item number Current item Current menu ● A visible menu bar indicates the menu list is too long to display all items. ● A band halfway down the menu bar indicates the current item is halfway down the list. ● The depth and relative position of the item band on the menu bar indicates the length of the menu list, and approximate position of the current item in the list. ● A deeper band indicates fewer items. Parameter view ① ② ③ Edit view Parameter name Parameter number Parameter value/selection SITRANS LR250 (mA/HART) 56 Operating Instructions, 08/2014, A5E32220602-AC Commissioning 6.2 Operating via the handheld programmer 6.2.2.2 Handheld programmer (Part No. 7ML1930-1BK) The programmer is ordered separately. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 57 Commissioning 6.2 Operating via the handheld programmer Key functions in measurement mode Key Function Result Updates the loop current New value is displayed in LCD secondary region. Updates internal enclosure temperature reading Updates echo confidence value New value is displayed in LCD secondary region. Updates distance measurement Mode opens PROGRAM mode Opens the menu level last displayed in this power cycle, unless power has been cycled since exiting PROGRAM mode or more than 10 minutes have elapsed since PROGRAM mode was used. Then top level menu will be displayed. RIGHT arrow opens PROGRAM mode Opens the top level menu. UP or DOWN arrow toggles between linear units and percent LCD displays measured value in either linear units or percent. SITRANS LR250 (mA/HART) 58 Operating Instructions, 08/2014, A5E32220602-AC Commissioning 6.2 Operating via the handheld programmer 6.2.3 Programming Note • While the device is in PROGRAM mode the output remains fixed and does not respond to changes in the device. • The device automatically returns to Measurement mode after a period of inactivity in PROGRAM mode (between 15 seconds and 10 minutes, depending on the menu level). Change parameter settings and set operating conditions to suit your specific application. For remote operation see Operating via SIMATIC PDM (Page 77) or Operating via AMS Device Manager (Page 103). Parameter menus Note For the complete list of parameters with instructions, see Parameter Reference (Page 127). Parameters are identified by name and organized into function groups. See LCD menu structure (Page 293). 1. QUICK START 2. SETUP 2.1. DEVICE ............ 2.7. LINEARIZATION 2.7.1. VOLUME 2.7.1.1. VESSEL SHAPE SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 59 Commissioning 6.2 Operating via the handheld programmer 1. Enter PROGRAM mode ● Point the programmer at the display from a maximum distance of 300 mm (1 ft). ● RIGHT arrow ● Mode activates PROGRAM mode and opens menu level 1. opens the menu level last displayed in PROGRAM mode within the last 10 minutes, or menu level 1 if power has been cycled since then. ① Handheld programmer ② Display ③ Maximum distance: 300 mm (1 ft) 2. Navigating: key functions in Navigation mode Note • In Navigation mode ARROW keys move to the next menu item in the direction of the arrow. • For Quick Access to parameters via the handheld programmer, press Home , then enter the menu number, for example: 2.7.1. (Volume). SITRANS LR250 (mA/HART) 60 Operating Instructions, 08/2014, A5E32220602-AC Commissioning 6.2 Operating via the handheld programmer Key Name Menu level Function UP or DOWN arrow menu or parameter Scroll to previous or next menu or parameter RIGHT arrow menu Go to first parameter in the selected menu, or open next menu. parameter Open Edit mode. LEFT arrow menu or parameter Open parent menu. Mode menu or parameter Change to MEASUREMENT mode. Home menu or parameter Open top level menu: menu 1. 3. Editing in PROGRAM mode ● Navigate to the desired parameter. ● Press RIGHT arrow to open parameter view. ● Press RIGHT arrow again to open Edit mode. The current selection is highlighted. Scroll to a new selection. ● Press RIGHT arrow to accept it. The LCD returns to parameter view and displays the new selection. ① Parameter name ② Parameter number ③ Current selection SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 61 Commissioning 6.2 Operating via the handheld programmer 4. Changing a numeric value ● Navigate to the desired parameter. ● Press RIGHT arrow to open parameter view. The current value is displayed. ● Press RIGHT arrow again to open Edit mode. The current value is highlighted. ● Key in a new value. ● Press RIGHT arrow to accept it. The LCD returns to parameter view and displays the new selection. ① Parameter name ② Parameter number ③ Current selection SITRANS LR250 (mA/HART) 62 Operating Instructions, 08/2014, A5E32220602-AC Commissioning 6.2 Operating via the handheld programmer Key functions in edit mode Key Name Function UP or DOWN arrow Selecting options Scrolls to item. Numeric editing • Increments or decrements digits • Toggles plus and minus sign Selecting options • Accepts the data (writes the parameter) • Changes from Edit to Navigation mode • Moves cursor one space to the right • or, with cursor on Enter sign, accepts the data and changes from Edit to Navigation mode RIGHT arrow Numeric editing LEFT arrow: Selecting options Cancels Edit mode without changing the parameter. Numeric editing • Moves cursor to plus/minus sign if this is the first key pressed • or moves cursor one space to the left Clear Numeric editing Erases the display. Decimal point Numeric editing Enters a decimal point. Plus or minus sign Numeric editing Changes the sign of the entered value. Numeral Numeric editing Enters the corresponding character. to SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 63 Commissioning 6.2 Operating via the handheld programmer 6.2.3.1 Quick Start Wizard via the handheld programmer Note • A reset to factory defaults should be performed before running the Quick Start Wizard if the device has been used in a previous application. See Master Reset (4.1.). • The Quick Start wizard settings are inter-related and changes apply only after you select Finish in the Wizard Complete step. • Do not use the Quick Start wizard to modify parameters: see instead Parameter Reference (Page 127). (Perform customization for your application only after the Quick Start has been completed). • Default settings in the parameter tables are indicated with an asterisk (*). 1. Quick Start 1.1. Quick Start Wiz ● Point the programmer at the display from a maximum distance of 300 mm (1 ft), then press RIGHT arrow to activate PROGRAM mode and open menu level 1. ● Press RIGHT arrow twice to navigate to menu item 1.1 and open parameter view. ● Press RIGHT arrow to open Edit mode or DOWN arrow to accept default values and move directly to the next item. ● To change a setting, scroll to the desired item or key in a new value. ● After modifying a value, press RIGHT arrow to accept it and press DOWN arrow to move to the next item. ● Quick Start settings take effect only after you select Finish. SITRANS LR250 (mA/HART) 64 Operating Instructions, 08/2014, A5E32220602-AC Commissioning 6.2 Operating via the handheld programmer Material Selects the appropriate echo processing algorithms for the material [see Position Detect (2.8.4.2.) for more detail]. Options LIQUID LIQUID LOW DK a) (low dielectric liquid – CLEF algorithm enabled) a) dK < 3.0 Response Rate Sets the reaction speed of the device to measurement changes in the target range. Use a setting just faster than the maximum filling or emptying rate (whichever is greater). Options Response Rate (1.3.) Fill rate per Minute (2.4.2.)/Empty rate per Minute (2.4.3.) SLOW 0.1 m/min (0.32 ft/min) MED 1.0 m/min (3.28 ft/min) FAST 10.0 m/min (32.8 ft/min) SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 65 Commissioning 6.2 Operating via the handheld programmer Units Sensor measurement units. Options m, cm, mm, ft, in. Default: m Operation Operation Description NO SERVICE Measurement and associated loop current are not updated, and the device defaults to Fail-safe mode a). LEVEL Distance to material surface referenced from Low Calibration Point SPACE Distance to material surface referenced from High Calibration Point DISTANCE Distance to material surface referenced from Sensor reference point a) See Material Level (2.5.1.) for more detail. SITRANS LR250 (mA/HART) 66 Operating Instructions, 08/2014, A5E32220602-AC Commissioning 6.2 Operating via the handheld programmer ① ② ③ ④ ⑤ ⑥ Space Level Distance High Calibration Point (process full level) Sensor reference point a) Low Calibration Point (process empty level) The point from which High and Low Calibration points are referenced: see Dimension drawings. a) Low Calibration Point Distance from Sensor Reference to Low Calibration Point: usually process empty level. (See Operation for an illustration.) Values Range: 0.00 to 20.00 m High Calibration Point Distance from Sensor reference point to High Calibration Point: usually process full level. (See Operation for an illustration.) Values Range: 0.00 to 20.00 m SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 67 Commissioning 6.2 Operating via the handheld programmer Wizard complete Options BACK, CANCEL, FINISH (Display returns to 1.1 Quick Start Wiz menu when Quick Start is successfully completed.) Press DOWN arrow (Finish). Then press LEFT arrow to return to Measurement mode. SITRANS LR250 is now ready to operate. 6.2.3.2 Auto False Echo Suppression If you have a vessel with known obstructions, we recommend using Auto False Echo Suppression to prevent false echo detection. See TVT setup (2.8.7.) for instructions. This feature can also be used if the display shows a false high level, or the reading is fluctuating between the correct level and a false high level. SITRANS LR250 (mA/HART) 68 Operating Instructions, 08/2014, A5E32220602-AC Commissioning 6.2 Operating via the handheld programmer 6.2.3.3 Requesting an Echo Profile • In PROGRAM mode, navigate to: Level Meter > 3. > 3.1. • Press RIGHT arrow ① ② ③ ④ ⑤ ⑥ to request a profile. ⑦ Distance from Low Calibration Point to vertical cross-hair ⑧ Algorithm: tF (trueFirst) ⑨ Distance from flange face to target ⑩ Pan left/right - selected ⑪ Confidence Zoom Measure Exit Exit icon selected Exit icon deselected Pan up/down ● Use UP or DOWN arrow to scroll to an icon. When an icon is highlighted, that feature becomes active. ● To move a cross-hair, press RIGHT arrow to increase the value, LEFT arrow to decrease. ● To Zoom into an area, position the intersection of the cross-hairs at the center of that area, select Zoom, and press RIGHT arrow. Press LEFT ● To update the profile, select Measure and press RIGHT arrow to Zoom out. arrow. ● To return to the previous menu, select Exit then press RIGHT arrow. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 69 Commissioning 6.3 Application examples 6.3 Application examples Note In the applications illustrated below, values are for example purposes only. You can use these examples as setup references. Enter the values in the parameter tables to select the corresponding functions. Configure the basic settings using the Quick Start wizard parameters. (These parameters are inter-related, and changes take effect only after you select FINISH to apply changes in the final step.) In each example, after performing a Quick Start, navigate to the other required parameters either via the handheld programmer, or using a Device Management tool (SIMATIC PDM or AMS Device Manager) and enter the appropriate values. SITRANS LR250 (mA/HART) 70 Operating Instructions, 08/2014, A5E32220602-AC Commissioning 6.3 Application examples 6.3.1 Liquid resin in storage vessel, level measurement Note Minimum distance from flange face to target is limited by Near Range (2.8.1.). To obtain level measurement/4 to 20 mA output proportional to resin levels: ● Low Calibration Pt. = 5 m (16.5 ft) from sensor reference point ● High Calibration Pt.= 0.5 m (1.64 ft) from sensor reference point ● Max.fill/empty rate = 0.2 m/min (0.65 ft/min) In the event of a loss of echo: ● SITRANS LR250 is to go into Fail-safe High after 2 minutes. ① ② ③ ④ Sensor reference point High calibration point 0.5 m ⑤ ⑥ ⑦ 5m Low calibration point 0% level 100% level SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 71 Commissioning 6.3 Application examples Parameter type Parameter No. /Name Options/ Values Function Quick Start Wizard parameters Introduction NEXT Continue with Wizard. Language NEXT Continue with current language. Material LIQUID Response Rate MED Medium =1 m/minute Units meters Operation LEVEL Level Low Calibration Point 5 m (16.5 ft) High Calibration Point 0.5 0.5 m (1.64 ft) Wizard Complete FINISH Transfers Quick Start settings to device. LOE Timer (2.5.2.) 2 minutes Material Level (2.5.1.) HI Fail-safe level set to High Independent parameters Return to Measurement: press Mode 6.3.2 to start normal operation. Horizontal vessel with volume measurement Note The minimum distance from the flange face to the target is limited by Near Range (2.8.1.). To obtain level measurement/4 to 20 mA output proportional to vessel volume in a chemical vessel: ● Low Calibration Point = 3.5 m (11.48 ft) from sensor reference point ● High Calibration Point = 0.5 m (1.64 ft) from sensor reference point ● Max. fill/empty rate = 0.2 m/min (0.65 ft/min) Select vessel shape, Parabolic Ends, and enter values for A and L, to obtain a volume reading instead of level. In the event of a loss of echo: SITRANS LR250 is to go into Fail-safe High after 2 minutes. SITRANS LR250 (mA/HART) 72 Operating Instructions, 08/2014, A5E32220602-AC Commissioning 6.3 Application examples ① ② ③ ④ ⑤ Sensor reference point 0.5 m High Calibration Point 3.5. m ⑥ ⑦ ⑧ ⑨ A = 0.8 m L=6m 100% = 8000 L Volume reading Low Calibration Point Parameter type Parameter No./Name Options/ Values Quick Start Wizard parameters Introduction NEXT Continue with Wizard. Language NEXT Continue with current language. Material LIQUID Response Rate MED Units meters Operation LEVEL Level is reported as Volume when a vessel shape is selected. Low Calibration Point 3.5 3.5 m (11.48 ft) High Calibration Point 0.5 0.5 m (1.64 ft) Wizard Complete FINISH Transfers Quick Start settings to device. Vessel Shape (2.7.1.1.) PARABOLIC ENDS Defines vessel shape. Maximum Volume (2.7.1.2.) 8000 8000 liters Vessel Dimension A (2.7.1.3.) 0.8 0.8 m (2.62 ft) Vessel Dimension L (2.7.1.4.) 6 m (19.68 ft) LOE Timer (2.5.2.) 2 minutes Material Level (2.5.1.) HI Fail-safe level set to High Independent parameters Return to Measurement: press Mode Function Medium =1 m/minute to start normal operation. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 73 Commissioning 6.3 Application examples 6.3.3 Application with stillpipe Note • Near Range (2.8.1.) (Blanking) will be set at the factory. Check the process connection tag for specific values. • Suitable pipe diameters are 40 mm (1.5") to 100 mm (4"). • The pipe diameter must be matched with the antenna size. Use the largest antenna size that will fit the stillpipe/bypass pipe. See Dimensions (Page 209). • See Mounting on a Stillpipe or Bypass Pipe (Page 32) for installation guidelines. This application is to obtain a level measurement and corresponding 4 to 20 mA output proportional to the oil level in a fuel storage vessel. ● Low Calibration Pt. is 5 m (16.5 ft) from the sensor reference point. ● High Calibration Pt. is 0.5 m (1.65 ft) from the sensor reference point. ● The stillpipe inside diameter is 50 mm (1.96"). ● The maximum rate of filling or emptying is about 0.1 m (4")/min. ① ② ③ ④ sensor reference point high calibration point 0.5 m ⑤ ⑥ ⑦ 5m 50 mm I.D. low calibration point vent hole SITRANS LR250 (mA/HART) 74 Operating Instructions, 08/2014, A5E32220602-AC Commissioning 6.3 Application examples Parameter type Parameter No./Name Options/Values Function Quick Start Wizard Introduction NEXT Continue with Wizard. Language NEXT Continue with current language. Material LIQUID LOW DK Response Rate MED Units meters Operation LEVEL Level is reported as Volume when a vessel shape is selected. Low Calibration Point 5 m (16.5 ft) High Calibration Point 0.5 0.5 m (1.64 ft) Wizard Complete FINISH Transfers Quick Start settings to device. Propagation Factor (2.8.3.)a) 0.988 P.F. for a 50 mm (1.96") I.D. stillpipe Position Detect (2.8.4.2.) HYBRID CLEF Range (2.8.4.4.)a) 4.3 Independent parameters a) Medium =1 m/minute Low calibration point 0.7 m = 4.3 m (14.1 ft) The recommended values for the propagation factor and for CLEF range are dependent on the stillpipe diameter. Refer to the next table for values. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 75 Commissioning 6.3 Application examples Propagation Factor/Stillpipe Diameter ① ② sensor reference point ③ ④ 700 or 1000 mm (see CLEF Range settings in table below) air gap Values low calibration point CLEF range 2.8.4.4. Range 0.3 to 1.0 depending on pipe size Default 1.0000 Nominal Pipe Size a) 40 mm (1.5") 50 mm (2") 80 mm (3") 100 mm (4") Propagation Factor 0.9844 0.988 0.9935 0.9965 CLEF Range (2.8.4.4.) settings Low calibration point 700 mm (2.29 ft)b) Low calibration point 700 mm (2.29 ft)b) Low calibration point -1000 mm (3.28 ft)b) Low calibration point -1000 mm (3.28 ft)b) a) Since pipe dimensions may vary slightly, the propagation factor may also vary. b) CLEF range covers the whole measurement range except first 700 or 1000 mm from sensor reference point Note Flanged and Hygienic encapsulated antenna For Flanged encapsulated antenna (7ML5432) and Hygienic encapsulated antenna (7ML5433 ) match the process connection size to the pipe diameter. For example, DN80/3" flange to DN80/3" pipe. SITRANS LR250 (mA/HART) 76 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM SIMATIC PDM is a software package used to commission and maintain process devices. Please consult the operating instructions or online help for details on using SIMATIC PDM. You can find more information on versions and compatibility at our website: SIMATIC PDM (www.siemens.com/simatic-pdm). 7.1.1 Functions in SIMATIC PDM Note • For a complete list of parameters, see Parameter Reference (Page 127). • While the device is in PROGRAM mode the output remains fixed and does not respond to changes in the device. 7.1.1.1 PDM function overview SIMATIC PDM monitors the process values, alarms and status signals of the device. It allows you to display, compare, adjust, verify, and simulate process device data; also to set schedules for calibration and maintenance. Parameters are identified by name and organized into function groups. See LCD menu structure (Page 293) for a chart and Changing parameter settings using SIMATIC PDM (Page 86) for more details. The menu structure for SIMATIC PDM is almost identical to that for the LCD. See Parameters accessed via pull-down menus (Page 87) for parameters that do not appear in the menu structure in SIMATIC PDM. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 77 Remote operation 7.1 Operating via SIMATIC PDM 7.1.1.2 Features of SIMATIC PDM Rev. 6.0, SP4 or higher The graphic interface in the device makes monitoring and adjustments easy. 7.1.1.3 Feature Function Quick Start (Page 81) Device configuration for simple applications Echo Profile Utilities (Page 88) Easy access to echo profile viewing/comparison, TVT shaping, auto false echo suppression and echo setup Auto False Echo Suppression (Page 92) Screen out false echoes TVT Shaper (Page 91) Manual TVT adjustment Process Variables (Page 99) Monitor process variables and level trend Security (Page 102) Protect security and communication parameters from modification by the maintenance user Features of SIMATIC PDM Rev. 5.2, SP1 SIMATIC PDM Rev. 5.2 SP1 is supported only for basic configuration and troubleshooting. For advanced features such as the Quick Start wizard, Rev. 6.0 SP3 HF2 or higher is required. 7.1.1.4 SIMATIC PDM Version Check the support page of our website to make sure you have the latest version of SIMATIC PDM, the most recent Service Pack (SP) and the most recent hot fix (HF): SIMATIC PDM Version (https://support.automation.siemens.com). Browse to Product Information > Automation Technology > Process control systems > SIMATIC PCS 7 > System components > SIMATIC PDM. 7.1.2 Initial setup To ensure that SIMATIC PDM connects properly, complete the following two processes: 1. De-activate buffers 2. Update the Electronic Device Description (EDD) SITRANS LR250 (mA/HART) 78 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM 7.1.2.1 Deactivating buffers This deactivation is required to align SIMATIC PDM with the HART modem for Windows 2000® and Windows® XP operating Systems. Windows® is a registered trademark of the Microsoft Corporation. Note • This deactivation is only necessary when you're connecting via RS232 (COM1) as opposed to USB. • You will need administrative rights on your operating system to deactivate buffers. • SIMATIC PDM operates only in the Windows XP Professional version, not in the Home version. 1. Click Start/Settings/Control Panel to begin configuration. 2. Double click System, select the Hardware tab, and click the Device Manager button. 3. Open Ports folder and double click the COM Port used by the system to open the Communications Port Properties window. 4. Select the Port Settings tab and double click the Advanced button. 5. If the Use FIFO buffers radio box is selected, click to deselect. ① Deselect Use FIFO buffers radio box 6. Click OK to close out. Close all screens and then reboot. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 79 Remote operation 7.1 Operating via SIMATIC PDM 7.1.3 Updating the Electronic Device Description (EDD) You can locate the EDD in Device Catalog, under Sensors/Level/Echo/SiemensMilltronics/SITRANS LR250. The EDD revision must match the Firmware revision in the device. To install a new EDD: 1. Download the most current EDD from our website: Product page (http://www.siemens.com/LR250) 2. Save files to your computer, and extract the zipped file to an easily accessed location. 3. Launch SIMATIC PDM – Manage Device Catalog, browse to the unzipped EDD file and select it. 7.1.3.1 Configuring a new device Note • Clicking on Cancel during an upload from device to SIMATIC PDM will result in some parameters being updated. • Application Guides for setting up HART devices with SIMATIC PDM can be downloaded from our website: Product page (http://www.siemens.com/LR250). 1. Check that you have the most recent EDD, and if necessary update it. [See Updating the Electronic Device Description (EDD) (Page 80) above]. 2. Launch SIMATIC Manager and create a new project for the device. 3. Open the menu Device – Master Reset and click on OK to perform a reset to Factory Defaults. 4. After the reset is complete upload parameters to the PC/PG. 5. Configure the device via the Quick Start wizard. SITRANS LR250 (mA/HART) 80 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM 7.1.4 Quick Start Wizard via SIMATIC PDM The graphic Quick Start Wizard provides an easy step-by-step procedure that configures the device for a simple application. Please consult the operating instructions or online help for details on using SIMATIC PDM. 1. If you have not already done so, check that you have the most up-to-date Electronic Device Description (EDD) for your device. [See Configuring a new device (Page 80).] 2. Launch SIMATIC Manager and create a new project. Application Guides for setting up HART and PROFIBUS PA devices with SIMATIC PDM can be downloaded from the product page of our website: Product page (http://www.siemens.com/LR250) Quick start Note • A reset to Factory Defaults should be performed before running the Quick Start Wizard if device has been used in a previous application. See Master Reset via SIMATIC PDM (Page 98). • The Quick Start wizard settings are inter-related and changes apply only after you click on FINISH AND DOWNLOAD at the end of the last step to save settings offline and transfer them to the device. • Do not use the Quick Start Wizard to modify individual parameters: for quick access to echo profile parameters, see Echo Profile via SIMATIC PDM (Page 89) or see Parameter Reference (Page 127) for a complete list. (Perform customization only after the Quick Start has been completed.) • Click on BACK to return and revise settings or CANCEL to exit the Quick Start. • For a vessel with obstructions see Auto False Echo Suppression via SIMATIC PDM (Page 92). Launch SIMATIC PDM, open the menu Device – Wizard - Quick Start, and follow steps 1 to 5. ① Quick Start SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 81 Remote operation 7.1 Operating via SIMATIC PDM Step 1 – Identification Note • The layout of the dialog boxes shown may vary according to the resolution setting for your computer monitor. • SITRANS PDM limits the TAG field to a maximum of 24 characters. 1. Click on Read Data from Device to upload Quick Start parameter settings from the device to the PC/PG and ensure PDM is synchronized with the device. 2. If required, change the language for the local user interface. 3. Click on NEXT to accept the default values. (Description, Message, and Installation Date fields can be left blank.) SITRANS LR250 (mA/HART) 82 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM Step 2 – Application Select the application type (level or volume) and the material, then click on NEXT. See Application with Stillpipe (Page 74) for a Low Dielectric Liquid application. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 83 Remote operation 7.1 Operating via SIMATIC PDM Step 3 – Vessel Shape The vessel shapes shown are predefined. For a vessel with obstructions, see Auto False Echo Suppression via SIMATIC PDM (Page 92). Select the vessel shape, and click on NEXT. SITRANS LR250 (mA/HART) 84 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM Step 4 – Ranges Set the parameters, and click on NEXT. Step 5 – Summary Check parameter settings, and click on BACK to return and revise values, FINISH to save settings offline, or FINISH AND DOWNLOAD to save settings offline and transfer them to the device. The message Quick Start was successful will appear. Click on OK. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 85 Remote operation 7.1 Operating via SIMATIC PDM 7.1.5 Changing parameter settings using SIMATIC PDM Note • For a complete list of parameters, see Parameter Reference (Page 127). • Clicking on Cancel during an upload from device to SIMATIC PDM will result in some parameters being updated. Many parameters are accessed via pull-down menus in PDM. See Parameters accessed via pull-down menus (Page 87) for others. 1. Launch SIMATIC PDM, connect to device, and upload data from device. 2. Adjust parameter values in the parameter value field then Enter. The status fields read Changed. 3. Open the Device menu, click on Download to device, then use File - Save to save settings offline. The status fields are cleared. ① Value fields SITRANS LR250 (mA/HART) 86 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM 7.1.6 Parameters accessed via pull-down menus Click on Device or View to open the associated pull-down menus. ① pull-down menus Pull-down menus Device menus View menus Communication path Process Variables (Page 99) Download to device Device Status (Page 101) Upload to PC/PG Toolbar Update Diagnostic Status Status bar Wizard - Quick Start (Page 81) Update Echo Profile Utilities (Page 88) Maintenance (Page 95) Wear (Page 98) Select Analog Output (Page 97) Self Test (Page 97) Loop Test (Page 97) Configuration Flag Reset (Page 97) Master Reset (Page 98) HART Communication (Page 98) SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 87 Remote operation 7.1 Operating via SIMATIC PDM 7.1.6.1 Echo profile utilities Open the menu Device – Echo Profile Utilities and click on the appropriate tab for easy access to: ● Echo profile (Page 89) ● View Saved Echo Profiles (Page 90) ● TVT Shaper (Page 91) ● Auto False Echo Suppression (Page 92) ● Echo Setup (Page 95) SITRANS LR250 (mA/HART) 88 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM 7.1.6.2 Echo profile Note • Double click on each axis to see the Xscale and Data Scale values. • To zoom in to a section of the profile, left-click and drag a marquee around it. Right click inside the window to zoom out. • Expand or compress the x and/or y axes: – Left-click on the axis and drag in either direction to reposition the low end of the scale. – Right-click on the axis and drag in either direction to reposition the high end of the scale. • After saving a profile click on OK, not the x button, to close the Echo Profile Utilities window, otherwise the profile will not be saved. ● In the Echo Profile Utilities window click the Echo Profile tab. ● Initial profile graph is blank upon entry to dialog. Click Measure to update the profile. ● It is recommended to use the Detailed resolution view of the echo profile for troubleshooting. For faster and more coarse views, the Standard resolution may be used. ● Click Save and in the new window enter a name and click OK. ● Click OK to exit. ① ② Resolution Echo Profile Time Based Storage SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 89 Remote operation 7.1 Operating via SIMATIC PDM 7.1.6.3 View saved echo profiles To view a saved profile, click on the tab View Saved Echo Profiles. Echo profile data logging You can store up to 60 profiles at a selected interval (maximum 60 minutes). Inside Echo Profile Utilities, in the Echo Profile Time Based Storage window: ● Enter the desired interval between stored profiles. ● Enter the maximum number of profiles to be stored (maximum 60). ● Click on Start. A message appears warning of the time delay and warning that all previous saved profiles will be overwritten. Click on OK to proceed. The new profiles will be saved with their date and time. ● Click on the tab View Saved Echo Profiles to view the stored profiles. SITRANS LR250 (mA/HART) 90 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM 7.1.6.4 TVT Shaper Note Double click on each axis to see the X scale and data scale values. Right-click or Left-click on the axis and drag to reposition the scale. This feature allows you to manually adjust the TVT to avoid false echoes caused by obstructions. For an explanation see Auto False Echo Suppression (Page 259). Open the menu Device – Echo Profile Utilities and click the tab TVT Shaper. ① ② ③ TVT Cursor Echo profile ● Initial profile graph is blank upon entry to dialog. Click on Measure to view and upload the current TVT from device. ● Change the position of the cursor on the TVT using the Point+ and Point– buttons: raise and lower the TVT using Offset+ and Offset-. ● Alternatively, enter values for Point and Offset directly into the dialog boxes. ● Click on Transfer to Device. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 91 Remote operation 7.1 Operating via SIMATIC PDM 7.1.6.5 Auto false echo suppression Note • Ensure material level is below all known obstructions when using Auto False Echo Suppression to learn the echo profile. An empty or almost empty vessel is recommended. • Note the distance to material level when learning the echo profile, and set Auto False Echo Suppression Range to a shorter distance to avoid the material echo being screened out. • Set Auto False Echo Suppression and Auto False Echo Suppression Range during startup, if possible. • If the vessel contains an agitator it should be running. • Before adjusting these parameters, rotate the device for best signal (lower false-echo amplitude). If you have a vessel with known obstructions, use Auto False Echo Suppression to prevent false echo detection. This feature can also be used if the device displays a false high level, or the reading is fluctuating between the correct level and a false high level. The device learns the echo profile over the whole measurement range and the TVT is shaped around all echoes present at that moment. See Auto False Echo Suppression (Page 259) for a more detailed explanation. SITRANS LR250 (mA/HART) 92 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM The learned TVT will be applied over a specified range. The default TVT is applied over the remainder of the measurement range. 1. Make sure the material level is below all known obstructions. 2. Determine Auto False Echo Suppression Range. Measure the actual distance from the sensor reference point to the material surface using a rope or tape measure. Subtract 0.5 m (20") from this distance, and use the resulting value. 3. Open the menu Device – Echo Profile Utilities and click on the tab Auto False Echo Suppression. 4. Make sure Auto False Echo Suppression Range is On. 5. Enter the value for Auto False Echo Suppression Range. 6. Click Learn. The message appears: 'This will learn a new echo profile. Once done it cannot be undone'. Click OK. 7. Once Auto TVT is complete click Transfer to Device. To exit click Close. Auto TVT is enabled and the learned TVT will be used. 8. To turn Auto False Echo Suppression off or on, reopen the Auto False Echo Suppression window, change the Auto False Echo Suppression to Off or On, click on Transfer to Device. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 93 Remote operation 7.1 Operating via SIMATIC PDM Before Auto False Echo Suppression ① ② ③ TVT Hover Level Default TVT ④ ⑤ Echo marker ④ ⑤ ⑥ Material level Material level False echo After Auto False Echo Suppression ① ② ③ False echo Learned TVT Auto False Echo Suppression Range Default TVT Echo marker SITRANS LR250 (mA/HART) 94 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM 7.1.6.6 Echo setup Provides quick access to echo selection, filtering, and response rate parameters. Open the menu Device – Echo Profile Utilities and click on Echo Setup. 7.1.6.7 Maintenance You can set schedules and reminders for: ● device maintenance based on its projected lifetime ● sensor maintenance based on its projected lifetime ● service ● calibration SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 95 Remote operation 7.1 Operating via SIMATIC PDM To set Device/Sensor Maintenance schedules: 1. Open the menu Device – Maintenance, and click on the Remaining Device/Sensor Lifetime tab. 2. Modify desired values, and if desired, set reminders for either or both of Reminder 1 before Lifetime (Required)/Reminder 2 before Lifetime (Demanded). 3. Click Write. 4. Click Read, to see the effects of your modification. 5. Click Snooze to add a year to the Total Expected Device Life. To set Service/Calibration schedules: 1. Open the menu Device – Maintenance, and click on the Service/Calibration Schedule tab. 2. Modify desired values and if desired, set reminders for either or both of Reminder 1 before Lifetime (Required)/Reminder 2 before Lifetime (Demanded). 3. Click Write. 4. Click Read, to see the effects of your modification. 5. Click Service/Calibration Performed to reset the schedule. SITRANS LR250 (mA/HART) 96 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM 7.1.6.8 Select analog output Allows you to set the mA Output to report Level, Distance, Space, or Volume. See Current Output Function (2.6.1.) for an illustration. If a volume application is selected, mA Output is automatically set to Volume. See Analog Output (Page 262) for more details. 1. Open the menu Device – Select Analog Output. 2. Select Analog Output window displays the current setting: click OK. 3. Select a different setting and click OK. 4. Select Analog Output window displays the new setting: click OK. 7.1.6.9 Self test Checks memory (RAM and Flash). If there are no errors, returns the message 'Self Test OK.' If errors are found, returns the message 'Self Test Fails'. Open the menu Device – Self Test, select Yes and click OK. 7.1.6.10 Loop test Note The simulated AO (Analog Output) value influences output to the control system. Allows you to input a simulated value (4 mA, 20 mA, or a user-defined value) in order to test the functioning of the mA connections during commissioning or maintenance of the device. The range is 3.56 mA to 22.6 mA, see mA Output Value (2.6.6.). To simulate a user-defined mA value: 1. Open the menu Device – Loop Test. 2. Select Other, enter the new value, and click on OK. The message ’Field Device fixed at [new value]’ appears. Click on OK. The Loop Test window remains open. 3. When you are ready to end simulation, select End and click on OK to return the device to the actual output value. 7.1.6.11 Configuration flag reset To reset the configuration flag to zero, open the menu Device – Configuration Flag Reset and perform a reset. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 97 Remote operation 7.1 Operating via SIMATIC PDM 7.1.6.12 Master reset Factory Defaults Factory Defaults resets all parameters to the default settings with the following exceptions: ● Device Address (5.1.) remains unchanged if the reset command is sent remotely (via AMS, PDM, DTM, FC375) but is reset to 0 if the reset command is sent via LUI. ● Write Protect (6.2.1.) and PIN to Unlock (6.2.2.) ● Learned TVT curve, see Auto False Echo Suppression (2.8.7.1) 1. Open the menu Device – Master Reset, select Yes, and click on OK to perform a reset to Factory Defaults. 2. After the reset is complete upload parameters to the PC/PG. (If you are performing a reset after replacing the device with a different instrument, do not upload parameters to the PC/PG). 7.1.6.13 Wear Reports the number of hours the device has been operating, and the number of times it has been powered up. Open the menu Device – Wear to view: ● Powered Days ● Power-on Resets Note Powered days are whole days only. Fractional days are truncated. 7.1.6.14 HART Communication Sets the number of request/response preambles (default 5). The preamble consists of three or more hexadecimal FF characters (all 1s). This allows the receiving modem to get its frequency-detection circuits synchronized to the signal after any pause in transmission. We recommend you do not change the default value (5). SITRANS LR250 (mA/HART) 98 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM 7.1.6.15 Process variables To compare outputs in real time open the menu View – Process Variables and click on Overview to see reading (level, space, distance, volume); analog output; device status; and current electronics temperature. To see highest and lowest electronics temperatures, navigate to Level Meter > Maintenance and Diagnostics > Electronics Temperature. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 99 Remote operation 7.1 Operating via SIMATIC PDM 7.1.6.16 Trend Open the menu View – Process Variables and click on Trend. Four trend lines can be monitored (distinguished by color in SIMATIC PDM): ① ② ③ ④ Space Distance Level Volume SITRANS LR250 (mA/HART) 100 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.1 Operating via SIMATIC PDM 7.1.6.17 Device status Open the menu View – Device Status to view Diagnostics, Device Status, Hardware/ Firmware (HW/FW) Status, and Maintenance status. ① update diagnostics In the Diagnostics window, click on Update diagnostics to update diagnostic information and refresh linked icons. 7.1.6.18 Update Open the menu View – Update to refresh the screen. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 101 Remote operation 7.1 Operating via SIMATIC PDM 7.1.6.19 Security A password option protects security and communication control parameters from modification by a maintenance user. When you open a project the User dialog window provides two options: maintenance or specialist. If a password has been set it will not be possible to open the project as a specialist without it. A maintenance user will be able to open the project without a password but will not have access to security and communication control parameters. 1. Open a project, double-click on the device icon, and in the User window select Specialist. 2. Open the menu Options – Settings and click on the Password tab. 3. Enter a new password and re-enter it in the Confirmation window. Click on OK. SITRANS LR250 (mA/HART) 102 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.2 Operating via AMS Device Manager 7.2 Operating via AMS Device Manager AMS Device Manager is a software package that monitors the process values, alarms and status signals of the device. Please consult the operating instructions or online help for details on using AMS Device Manager. You can find more information at: Emerson (http://www.emersonprocess.com/AMS/) Application Guides for setting up Siemens HART devices with AMS Device Manager are available on our website: Process automation (www.siemens.com/processautomation) 7.2.1 Functions in AMS Device Manager Note While the device is in PROGRAM mode the output remains fixed and does not respond to changes in the device. 7.2.1.1 AMS function overview AMS Device Manager monitors the process values, alarms and status signals of the device. It allows you to display, compare, adjust, verify, and simulate process device data. Parameters organized into three main function groups allow you to configure and monitor the device: ● Configure/Setup ● Device Diagnostics (read only) ● Process Variables (read only) See AMS Menu Structure (Page 122) for a chart and Changing parameter settings using AMS Device Manager (Page 111) for more details. The menu structure for AMS Device Manager is almost identical to that for the LCD. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 103 Remote operation 7.2 Operating via AMS Device Manager 7.2.1.2 Features of AMS Device Manager The graphic interface in the radar device makes monitoring and adjustments easy. 7.2.1.3 Feature Function Quick Start (Page 107) Device configuration for simple applications Echo Profile (Page 116) Echo profile viewing TVT (Page 115) Screen out false echoes Linearization (Page 109) Volume measurement in an irregular vessel Process Variables (Page 120) Monitor process variables and level trend Security (Page 118) Protect security and communication parameters from modification by the maintenance user Electronic Device Description (EDD) The EDDs are linked to the type, version of configuration software, and protocol being used. Select the LR250 AMS EDD for the version of AMS installed. EDDs can be downloaded from our website, see Product page (http://www.siemens.com/LR250). The HART EDD for LR250 is labeled as supporting AMS Device Manager version 9.5. This EDD is also operational with AMS version 9.0 and 10.1. There is also an application guide that details how to use the Hart Communication Foundation EDDs in AMS version 11.5 and above. There is no EDD for the LR250 for AMS version 10.5 to 11.1. Please check the product page for updated EDDs and application guide. 7.2.1.4 Configuring a new device 1. Check our website to make sure you have the most recent EDD. Product page (http://www.siemens.com/LR250) Go to Support > Software Downloads and if necessary download it. Save the files to your computer, and extract the zipped file to an easily accessed location. 2. Launch AMS Device Manager– Add Device Type, browse to the unzipped EDD file and select it. SITRANS LR250 (mA/HART) 104 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.2 Operating via AMS Device Manager 7.2.1.5 Startup 1. Launch AMS Device Manager. (Application Guides for setting up HART devices with AMS Device Manager can be downloaded from our website: Product page (http://www.siemens.com/LR250) 2. In Device Connection View right-click on the device icon and select Scan Device to upload parameters from the device. 3. Double click the device icon to open the startup screen. The startup screen shows device identification details, and a navigation window on the left-hand side of the screen. Master reset Note Device Address (5.1.) remains unchanged if the reset command is sent remotely (via AMS, PDM, DTM, FC375) but is reset to 0 if the reset command is sent via LUI. ● Navigate to Configure/Setup > Operation ● In the General field click on Master Reset and accept the option Factory Defaults. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 105 Remote operation 7.2 Operating via AMS Device Manager 7.2.1.6 Pull-down menu access ① Action menu items A pull-down menu under Actions gives alternative access to several features. Scan Device • Open the menu Actions – Scan Device. • Scan Device uploads parameters from the device (synchronizes parameters). SITRANS LR250 (mA/HART) 106 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.2 Operating via AMS Device Manager 7.2.1.7 Device configuration 1. Navigate to Configure/Setup > Operation and click to open the dialog window. 2. In the General field, click on Master Reset and perform a reset to Factory Defaults. 3. Open the pull-down menu Actions – Scan Device to synchronize parameters (upload parameters from the device to AMS). 4. Configure the device via the Quick Start wizard. ① 7.2.1.8 Master reset Quick Start Wizard via AMS Device Manager Note • A reset to Factory Defaults should be performed before running the Quick Start Wizard if device has been used in a previous application. See Master Reset (Page 105). • The layout of the dialog boxes shown may vary according to the resolution setting for your computer monitor. • At each step, you can accept the default values without modification and click on the next step to proceed. • After modifying parameters click on Apply inside the Quick Start window to write the new values to the device. • Click on OK only if you wish to update all parameters to the device and close AMS. A Wizard provides an easy 5-step Quick Start procedure that configures the device for a simple application. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 107 Remote operation 7.2 Operating via AMS Device Manager Quick Start Step 1 – Identification 1. Navigate to Configure/Setup > Wizard > Quick Start. 2. Click on Step 1. 3. You can accept the default values without modification. (Description, Message, and Installation Date fields can be left blank.) If desired, make changes then click on Apply. Step 2 – Application 1. Click on Step 2. 2. Select the application type (Level/vessel, Level/stillpipe, Level/bypass pipe, Volume/vessel, Volume/stillpipe, or Volume/bypass pipe) and the material (Liquid or Low dielectric liquid). 3. Click on Apply. Step 3 – Vessel Shape 1. Click on Step 3. 2. Select a predefined vessel shape. To describe a more complex shape see Linearization (Page 109). 3. Click on Apply. SITRANS LR250 (mA/HART) 108 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.2 Operating via AMS Device Manager Step 4 – Ranges 1. Click on Step 4. 2. Change units if desired (in meters by default). 3. Set High and Low Calibration points. 4. To convert the reading from level to volume enter a value for Maximum Volume. 5. If a vessel shape with parabolic ends has been selected, set dimensions A and L. 6. Click on Apply. Step 5 – Summary Check parameter settings, and click on Cancel to abort, or Apply to transfer values to the device. Linearization You can use the linearization feature to define a more complex vessel shape and enter up to 32 level breakpoints where the corresponding volume is known. The values corresponding to 100% and 0% levels must be entered. The breakpoints can be ordered from top to bottom, or the reverse. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 109 Remote operation 7.2 Operating via AMS Device Manager Using linearization via the Quick Start wizard Navigate to Configure/Setup > Wizard > Quick Start. In Step 1 – Identification, make any desired modifications and click on Apply. In Step 2 – Application, select a level application and liquid as a material. In Step 3 – Vessel Shape, choose the vessel shape option Linearization Table. In Step 4 – Ranges, enter a value for maximum volume. ① ② Breakpoints Maximum volume 1. Click on the Breakpoints tab and enter values for level and volume for up to 32 breakpoints. 2. Navigate to Configure/Setup > Setup > Linearization and click on Characteristic to preview the characteristic curve of the vessel breakpoints. (The conversion will function correctly even if not all breakpoints are entered, but the curve will display correctly only if all breakpoints are entered.) 3. In Step 5 – Summary, check parameter values. Click on the appropriate step menu to return and revise values, or click on a different menu to exit Quick Start. SITRANS LR250 (mA/HART) 110 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.2 Operating via AMS Device Manager Changing parameter settings using AMS Device Manager Note For a complete list of parameters, see Parameter Reference (Page 127). For more detailed explanations of the parameters listed below see the pages referenced. 1. Adjust parameter values in the parameter value field in Configure/Setup view, then click on Apply to write the new values to the device. The parameter field will display in yellow until the value has been written to the device. 2. Click on OK only if you wish to update all parameters and exit AMS. Operation Navigate to Configure/Setup > Operation and click on Operation to open the dialog window for access to: General ● Select Analog Output [see Select Analog Output (Page 97)] ● Master Reset [see Master Reset (Page 98)] Simulation/Test ● Self Test [see Self Test (Page 97)] ● Loop Test [see Loop Test (Page 97)] SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 111 Remote operation 7.2 Operating via AMS Device Manager Setup Note For more detailed explanations of the parameters listed below see the pages referenced. Sensor Navigate to Configure/Setup > Setup and click on Sensor for access to: General [see Sensor (2.2.)] ● Units ● Operating Mode ● Material ● Damping Filter Calibration [see Calibration (2.3.)] ● Low Calibration Point ● High Calibration Point ● Sensor Offset SITRANS LR250 (mA/HART) 112 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.2 Operating via AMS Device Manager Rate [see Rate (2.4.)] ● Response Rate ● Fill Rate per Minute ● Empty Rate per Minute Fail-safe [see Fail-safe (2.5.)] ● Material level ● Timer ● Level Analog Output Scale Navigate to Configure/Setup > Setup and click on Analog Output Scaling for access to: Analog Output Scaling [see Analog Output Scaling (2.6.)] ● Current Output Function ● 4 mA Setpoint ● 20 mA Setpoint ● Minimum mA Limit ● Maximum mA Limit SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 113 Remote operation 7.2 Operating via AMS Device Manager Signal Processing General Navigate to Configure/Setup > Setup > Signal Processing and click on General for access to: Range [see Signal Processing (2.8.)] ● Near Range ● Far Range ● Propagation Factor Echo Select [see Echo Select (2.8.4.)] ● Algorithm ● Position Detect ● Echo Threshold ● CLEF Range Sampling [see Sampling (2.8.5.)] ● Echo Lock ● Sampling Up ● Sampling Down Signal Quality ● Confidence ● Echo Strength ● Noise Average SITRANS LR250 (mA/HART) 114 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.2 Operating via AMS Device Manager TVT Modify the TVT to screen out false echoes. See Auto False Echo Suppression (2.8.7.1.) (Page 259). Navigate to Configure/Setup > Setup > Signal Processing and click on TVT. Click on one of the two tabs to access the parameters listed: TVT Setup [see TVT setup (2.8.7.)] ● Auto False Echo Suppression ● Auto False Echo Suppression Range ● Hover Level ● Shaper Mode TVT Shaper ● Shaper breakpoints 1 to 40. (Turn TVT Setup/Shaper Mode on to activate.) Manual TVT Curve Displays the effects of the TVT shaper modifications. Navigate to Configure/Setup > Setup > Signal Processing and click on Manual TVT Curve. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 115 Remote operation 7.2 Operating via AMS Device Manager Echo Profile ● Navigate to Configure/Setup > Setup > Signal Processing and click on Echo Profile. ● Select Standard operation for faster display. Local Display Navigate to Configure/Setup > Setup > Local Display for access to: ● Language ● LCD Fast Mode [see LCD Fast Mode (4.9.)] ● LCD Contrast [see LCD Contrast (4.10.)] 7.2.2 Maintenance and diagnostics Navigate to Maintenance and Diagnostics for access to: Remaining Device Lifetime [see Remaining Device Lifetime (4.2.)] ● Lifetime (expected) ● Time in Operation ● Remaining Lifetime ● Activation of Reminders ● Reminder 1 before Lifetime (Required) ● Reminder 2 before Lifetime (Demanded) Remaining Sensor Lifetime [see Remaining Sensor Lifetime (4.3.)] ● Lifetime (expected) ● Time in Operation ● Remaining Lifetime ● Activation of Reminders ● Reminder 1 before Lifetime (Required) ● Reminder 2 before Lifetime (Demanded) SITRANS LR250 (mA/HART) 116 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.2 Operating via AMS Device Manager Service Schedule [see Service Schedule (4.4.)] ● Service Interval ● Time Since Last Service ● Time Until Next Service ● Activation of Reminders ● Reminder 1 before Service (Required) ● Reminder 2 before Service (Demanded) Calibration Schedule [see Calibration Schedule (4.5.)] ● Calibration Interval ● Time Since Last Calibration ● Time Until Next Calibration ● Activation of Reminders ● Reminder 1 before Calibration (Required) ● Reminder 2 before Calibration (Demanded) Electronic Temperature ● Electronic Temperature ● Lowest Value ● Highest Value Wear ● Powered Days ● Poweron Resets See Wear via SIMATIC PDM (Page 98) for more detail. 7.2.3 Communication Navigate to Communication to read the following: Tag; Manufacturer’s ID; Device ID; Product ID; Device Revision; EDD Revision; Universal Command Revision SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 117 Remote operation 7.2 Operating via AMS Device Manager 7.2.4 Security Navigate to Configure/Setup > Security to access: Remote Access [see Remote Access (6.1.)] Note If access control is changed to limit remote access, it can only be reset via the handheld programmer. See Access Control (6.1.1.). ● Write Protect (read only) ● Access Control Local Access [see Local Access (6.2.)] ● Local Write Protected ● PIN to Unlock See also Password Protection (Page 121). SITRANS LR250 (mA/HART) 118 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.2 Operating via AMS Device Manager 7.2.5 Device Diagnostics Click on the Device Diagnostics bar at the bottom of the navigation window, for access to: Device Status Hardware/Firmware Status SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 119 Remote operation 7.2 Operating via AMS Device Manager 7.2.5.1 Process variables To compare outputs in real time click on Process Variables at the bottom of the navigation window for access to: Process Variables ● Values (level, volume, space, distance) ● Analog Output ● Trend View Echo Profile SITRANS LR250 (mA/HART) 120 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.2 Operating via AMS Device Manager 7.2.5.2 Password protection An AMS Device Manager administrator can configure the user to require a password. The use of passwords is recommended. A password should be assigned to the ’admin’ username immediately after installing AMS Device Manager. Each user is given an AMS Device Manager username and password and required to enter them when they start AMS Device Manager. Access to functions depends on the level of permissions granted. Login types ● standard, local, or domain A standard user can change their password in AMS Device Manager. A Local or Domain Windows user cannot change their password using AMS Device Manager and must request their network administrator to do so. 7.2.5.3 User Manager utility Usernames, passwords, and permissions, are assigned to users by an AMS Device Manager administrator, using the User Manager utility on the Server Plus Station. Only a user with AMS Device Manager System Administration rights can log in to User Manager. To configure a new user/edit existing user: 1. From the Windows taskbar select: Start > AMS Device Manager > User Manager. 2. In the User Manager window click on Add User. The Add User Wizard dialog allows you to: ● select a user type, standard (AMS Device Manager) or Window user. ● enter the username and password, and set permissions ● edit existing users SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 121 Remote operation 7.2 Operating via AMS Device Manager 7.2.6 AMS menu structure SITRANS LR250 (mA/HART) 122 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.2 Operating via AMS Device Manager SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 123 Remote operation 7.2 Operating via AMS Device Manager SITRANS LR250 (mA/HART) 124 Operating Instructions, 08/2014, A5E32220602-AC Remote operation 7.2 Operating via AMS Device Manager SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 125 Remote operation 7.3 Operating via FDT (Field Device Tool) 7.3 Operating via FDT (Field Device Tool) FDT is a standard used in several software packages designed to commission and maintain field devices. Two commercially available FDTs are PACTware and Fieldcare. Functionally FDT is very similar to PDM. See Operating via SIMATIC PDM (Page 77) for more detail. ● To configure a field device via FDT you need the DTM (Device Type Manager) for the device. ● To configure a field device via SIMATIC PDM, you need the EDD (Electronic Data Description) for the device. 7.3.1 Device Type Manager (DTM) A DTM is a type of software that ’plugs into’ FDT. It contains the same information as an EDD but an EDD is independent of the operating system. 7.3.2 SITRANS DTM ● SITRANS DTM is an EDDL interpreter developed by Siemens to interpret the EDD for that device. ● To use SITRANS DTM to connect to a device, you must first install SITRANS DTM on your system and then install the device EDD written for SITRANS DTM. ● You can download SITRANS DTM from the Siemens service and support website. Go to Service & Support (http://www.siemens.com/automation/service&support), click on Product Support, and drill down to Product Information/Automation Technology/Sensor systems/Process Instrumentation/Software & Communications. 7.3.3 The device EDD The SITRANS LR250 HART EDD for SITRANS DTM can be downloaded from our website: Product page (http://www.siemens.com/LR250). Go to Support > Software Downloads. 7.3.4 Configuring a new device via FDT The full process to configure a field device via FDT is outlined in an Application Guide which can be downloaded from our website under Support > Application Guides. Product page (http://www.siemens.com/LR250) SITRANS LR250 (mA/HART) 126 Operating Instructions, 08/2014, A5E32220602-AC 8 Parameter reference Note • Parameter names and menu structure are almost identical for SIMATIC PDM and the local user interface (LUI). • Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated. • Mode toggles between PROGRAM and Measurement Modes. • For Quick Access to parameters via the handheld programmer, press Home , then enter the menu number, for example: 2.2.1. • In Navigation mode, ARROW keys ( ) navigate the menu in the direction of the arrow. • Press RIGHT arrow to open Edit Mode, or to save a modification. Parameters are identified by name and organized into function groups. See LCD menu structure (Page 293) for a chart. For AMS Device Manager the structure varies slightly. Parameters accessible via the handheld programmer are followed by the device menu number in parenthesis. Parameters not followed by a number are accessible only via remote operation. For more details see: ● Operating via SIMATIC PDM (Page 77) ● Operating via AMS Device Manager (Page 103) Quick Start (1.) Wizards provide step-by-step procedures to configure the device, filter out false echoes, and upload and download parameters and firmware to the optional display for easy configuration of multiple devices. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 127 Parameter reference Quick Start Wizard (1.1.) From measurement screen, press RIGHT arrow twice to open the Quick Start Wizard menu. Select a wizard, press RIGHT arrow to open the first step, and follow the instructions. Note Do not use the Quick Start Wizard to modify individual parameters. (Perform customization only after the Quick Start has been completed.) ● See Quick Start Wizard via the handheld programmer (Page 64). ● See Quick Start Wizard via SIMATIC PDM (Page 77). ● See Quick Start Wizard via AMS Device Manager (Page 107). Setup (2.) Note Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated. Device (2.1.) Hardware Revision (2.1.1.) Corresponds to the electronics hardware of the SITRANS LR250. Firmware Revision (2.1.2.) Corresponds to the firmware that is embedded in the SITRANS LR250. Loader Revision (2.1.3.) Corresponds to the software used to update the SITRANS LR250. Order Option (2.1.4.) Read only. Displays the device type: standard or NAMUR NE 43-compliant. Menu Timeout (2.1.5.) Time menu stays visible before switching back to Measurement view if no key is pressed. SITRANS LR250 (mA/HART) 128 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Sensor (2.2.) Units (2.2.1.) PV (Primary Value) and SV (Secondary Sensor measurement units). Used in setting High/Low Calibration Point, and displayed on LCD and in PDM. Values m, cm, mm, ft, in Default: m SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 129 Parameter reference Sensor Mode (2.2.2.) ① Sensor value ⑤ ② ③ ④ Space ⑥ ⑦ ⑧ Distance High Calibration Point Sensor reference point [see Dimension drawings] (Page 209) Low Calibration Point Far range Level Mode Description NO SERVICE Measurement and associated loop current are n/a not updated, and the device defaults to Failsafe mode a). LEVEL Distance to material surface Low Calibration Point (process empty level) SPACE Distance to material surface High Calibration Point (process full level) DISTANCE Distance to material surface Sensor reference point a) Reference point See Material Level (2.5.1.) for more detail. SITRANS LR250 (mA/HART) 130 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Material (2.2.3.) Automatically configures the device to operate in the chosen application type, by changing one or more of the following parameters: Propagation Factor (2.8.3.), Position Detect (2.8.4.2.), and/or CLEF Range (2.8.4.4.). Options LIQUID LIQUID LOW DK a) (low dielectric liquid - CLEF algorithm enabled) Related parameters Propagation Factor (2.8.3.) Position Detect (2.8.4.2.) CLEF Range (2.8.4.4.) a) dK < 3.0 You can configure each of the related parameters to suit your particular application. Damping Filter (2.2.4.) The time constant for the damping filter. The damping filter smooths out the response to a sudden change in level. This is an exponential filter and the engineering unit is always in seconds [see Damping (Page 262) for more detail]. Values Range: 0 to 100.000 s Default: 10.000 s Calibration (2.3.) Note We recommend using the Quick Start wizard to configure the device. Low Calibration Pt. (2.3.1.) Distance from sensor reference point1) to Low Calibration Point. Units are defined in Units (2.2.1.) Values Range: 0 to 20 m. Default: 20.00 m Related parameters Units (2.2.1.) Far Range (2.8.2.) 1) The point from which level measurement is referenced, see Threaded Horn Antenna with extension (Page 209), Flanged Horn with extension (Page 214), and Flanged encapsulated antenna (3"/DN80/80A sizes and larger) (Page 220). SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 131 Parameter reference High Calibration Pt. (2.3.2.) Distance from sensor reference point 1) to High Calibration Point. Units are defined in Units (2.2.1.). Values Range: 0 to 20 m. Default 0.00 m Related parameters Units (2.2.1.) Near Range (2.8.1.) When setting the High Calibration Point value, note that echoes are ignored within Near Range (2.8.1.). The value produced by the echo processing which represents the distance from sensor reference point to the target. [see Threaded Horn Antenna with extension (Page 209), Flanged Horn with extension (Page 214), and Flanged encapsulated antenna (3"/DN80/80A sizes and larger) (Page 220)]. 1) Sensor Offset (2.3.3.) A constant offset that can be added to or subtracted from the sensor value1) to compensate for a shifted sensor reference point. (For example, when adding a thicker gasket or reducing the standoff/nozzle height.) The units are defined in Units (2.2.1.). Values Range: -100 to 100 m. Default: 0.00 m Related parameters Units (2.2.1.) The value produced by the echo processing which represents the distance from sensor reference point to the target, see Sensor Mode (2.2.2.). 1) SITRANS LR250 (mA/HART) 132 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Rate (2.4.) Response Rate (2.4.1.) Note Changing Response Rate resets Fill Rate per Minute (2.4.2.), Empty Rate per Minute (2.4.3.), and Damping Filter (2.2.4.). Sets the reaction speed of the device to measurement changes. Response Rate (2.4.1.) Fill Rate per Minute (2.4.2.) Empty Rate per Minute (2.4.3.) Damping Filter (2.2.4.) Slow 0.1 m/min (0.32 ft/min) 10 s Medium 1.0 m/min (3.28 ft/min) 10 s Fast 10.0 m/min (32.8 ft/min) 0s Use a setting just faster than the maximum filling or emptying rate (whichever is faster). Fill Rate per Minute (2.4.2.) Defines the maximum rate at which the reported sensor value is allowed to decrease. Allows you to adjust the SITRANS LR250 response to decreases in the actual material level. Fill Rate is automatically updated whenever Response Rate is altered. Options Range: 0 to 99999 m / min. Response Rate (2.4.1.) Fill Rate per Minute (2.4.2.) Slow 0.1 m/min (0.32 ft/min) Medium 1.0 m/min (3.28 ft/min) Fast 10.0 m/min (32.8 ft/min) Altered by: Response Rate (2.4.1.) Related parameters Units (2.2.1.) Enter a value slightly greater than the maximum vessel-filling rate, in units per minute. Sensor value is the value produced by the echo processing which represents the distance from sensor reference point to the target. See Sensor Mode (2.2.2.) for an illustration. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 133 Parameter reference Empty Rate per Minute (2.4.3.) Defines the maximum rate at which the reported sensor value is allowed to increase. Adjusts the SITRANS LR250 response to increases in the actual material level. Empty Rate is automatically updated whenever Response Rate is altered. Options Range: 0 to 99999 m / min. Response Rate (2.4.1.) Empty Rate per Minute (2.4.3.) Slow 0.1 m/min (0.32 ft/min) Medium 1.0 m/min (3.28 ft/min) Fast 10.0 m/min (32.8 ft/min) Altered by: Response Rate (2.4.1.) Related parameters Units (2.2.1.) Enter a value slightly greater than the vessel’s maximum emptying rate, in units per minute. Sensor value is the value produced by the echo processing which represents the distance from sensor reference point to the target. See Sensor Mode (2.2.2.) for an illustration. Fail-safe (2.5.) Note Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated. SITRANS LR250 (mA/HART) 134 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Material Level (2.5.1.) Note The default setting depends whether your device is a standard or NAMUR NE 43-compliant device. Defines the mA output to use when the Fail-safe timer expires. STANDARD DEVICE Options HI 20.5 mA (max. mA Limit) LO 3.8 mA (min. mA Limit) HOLD Last valid reading (default 22.6 mA) VALUE User-selected value [defined in Fail-Safe mA Value (2.5.3.)] NAMUR NE 43-COMPLIANT DEVICE1) Options 1) HI 20.5 mA (max. mA Limit) LO 3.8 mA (min. mA Limit) HOLD Last valid reading VALUE User-selected value [defined in Fail-Safe mA Value (2.5.3.): default 3.58 mA] Orderable option LOE Timer (2.5.2.) Note When a Loss of Echo occurs Material Level (2.5.1.) determines the material level to be reported when the Fail-safe timer expires. See Loss of Echo (LOE) (Page 264) for more detail. Sets the time to elapse since the last valid reading, before the Fail-safe Level is reported. Values Range: 0.00 to 7200 seconds Default: 100 s SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 135 Parameter reference Fail-Safe mA Value (2.5.3.) Note • The default settings are dependent on standard or NAMUR NE 43-compliant device. • Material Level (2.5.1.) must be set to VALUE to enable the Fail-Safe mA Value to be reported. Allows the user to define the mA value to be reported when the Fail-safe timer expires. Device Type Values STANDARD NAMUR NE43- COMPLIANT Range 3.56 mA to 22.6 mA Default 22.60 mA 3.58 mA Analog Output Scaling (2.6.) Current Output Function (2.6.1.) Note • Level, space, and distance, have different reference points. • Use caution when changing Current Output Function while the device is connected to a HART network. Current Output Function controls the primary value and the loop current for the device. • Current Output Function also affects the secondary, tertiary and quaternary variables in a HART network. Can be set to either Level, Space, Distance, or Volume. (The device can carry out a volume calculation only after a vessel shape has been specified.) ① ② ③ ④ Sensor reference point High calibration point 20 mA 100% Space ⑤ ⑥ ⑦ ⑧ 4 mA 0% Distance Level Low calibration point SITRANS LR250 (mA/HART) 136 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Options Reference point Description Level Low Calibration Point Space High Calibration Point measured as a percentage of the difference between High Calibration Point and Low Calibration Point Distance Sensor reference point Volume converts a level measurement to a volume output Manual a) allows mA Output Value (2.6.6.) to be set to a user-defined value measured as a percentage of Low Calibration Point (LUI only) a) Current Output Function must be set to Manual before modifying mA Output Value (2.6.6.). Remember to restore the previous Current Output Function setting after modifying mA Output Value. To view the mA reading in the secondary region of the LCD, press on the handheld programmer. To modify Current Output Function via SIMATIC PDM: ● Open the menu Device – Select Analog Output. See Select Analog Output via SIMATIC PDM (Page 97) for more detail. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 137 Parameter reference 4 mA Setpoint (2.6.2.) Sets the process level corresponding to the 4 mA value. 4 mA always defaults to 0, and Current Output Function (2.6.1.) determines whether this is a Level, Space, Distance, or Volume measurement. (See Current Output Function (2.6.1.) for an illustration.) Values Range: –999999 to +999999 (limits vary with current function and units) Default: 0.00 m (set to value corresponding to 0% as defined by Current Output Function) Related Parameters Units (2.2.1.) Current Output Function (2.6.1.) ● Enter the reading that is to correspond to a 4 mA output. ● Units are defined in Units (2.2.1.) for Level, Space, or Distance. Units are unspecified for Volume. 20 mA Setpoint (2.6.3.) Sets the process level corresponding to the 20 mA value. 20 mA always defaults to 100%, and Current Output Function (2.6.1.) determines whether this is a Level, Space, or Distance measurement. (See Current Output Function (2.6.1.) for an illustration.) Values Range: –999999 to +999999 (limits vary with current function and units) Default: 20.00 m (set to value corresponding to 100% as defined by Current Output Function) Related Parameters Units (2.2.1.) Current Output Function (2.6.1.) ● Enter the reading that is to correspond to a 20 mA output. ● Units are defined in Units (2.2.1.) for Level, Space, or Distance. Units are unspecified for Volume. Minimum mA limit (2.6.4.) Prevents the mA output from dropping below this minimum level for a measurement value. This does not restrict the Fail-safe or Manual settings. Values Range: 3.8 to 20.5 (mA) Default: 3.8 (mA) SITRANS LR250 (mA/HART) 138 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Maximum mA limit (2.6.5.) Prevents the mA output from rising above this maximum level for a measurement value. This does not restrict the Fail-safe or Manual settings. Values Range: 3.8 to 20.50 (mA) Default: 20.50 (mA) mA Output Value (2.6.6.) Allows you to use a simulated value to test the functioning of the loop. You can enter 4 mA, 20 mA, or any other user-defined value within the range. Values Range: 3.56 mA to 22.6 mA Read Only unless Current Output Function (2.6.1.) is set to Manual. Related parameter Current Output Function (2.6.1.) 1. First set Current Output Function (2.6.1.) to Manual. 2. Enter the desired mA value in mA Output Value. 3. After completing the test, remember to reset Current Output Function (2.6.1.) to the previous setting. Via SIMATIC PDM: Open the menu Device – Loop Test. For more detail, see Loop Test (Page 97). Linearization (2.7.) Volume (2.7.1.) Carries out a volume conversion from a level value. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 139 Parameter reference Vessel Shape (2.7.1.1.) Defines the vessel shape and allows the LR250 to calculate volume instead of level. If None is selected, no volume conversion is performed. Select the vessel shape matching the monitored vessel or reservoir. Vessel Shape LCD DISPLAY/ Description Also required None NONE/ No volume calculation required N/A CYLINDER/ Maximum volume Flat end horizontal cylinder SPHERE/ Sphere Maximum volume LINEAR/ Upright, linear (flat bottom) Maximum volume CONICAL BOT/ Conical or pyramidal bottom Maximum volume, dimension A PARABOLIC BOT/Parabolic bottom Maximum volume, dimension A HALF SPHERE BOT/ Half-sphere bottom Maximum volume, dimension A SITRANS LR250 (mA/HART) 140 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Vessel Shape a) LCD DISPLAY/ Description Also required FLAT SLOPED BOT/ Flat sloped bottom Maximum volume, dimension A PARABOLIC ENDS/ Parabolic end horizontal cylinder Maximum volume, dimension A, dimension LINEAR TABLE a) / Linearization table (level/volume breakpoints) Maximum volume, tables 1-32 level and volume breakpoints Linearization Table must be selected in order for level/volume values [see Table 1-8 (2.7.2.)] to be transferred. Maximum Volume (2.7.1.2.) The maximum volume of the vessel. Enter the vessel volume corresponding to High Calibration Point. For example, if your maximum vessel volume is 8000 L, enter a value of 8000. Volume units are defined by the user but are not explicitly stated or shown in the SITRANS LR250. Values Range: 0.0 to 99999 m Default: 100.0 Related Parameters Low Calibration Pt. (2.3.1.) High Calibration Pt. (2.3.2.) Vessel Shape (2.7.1.1.) SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 141 Parameter reference Vessel Dimension A (2.7.1.3.) The height of the vessel bottom when the bottom is conical, pyramidal, parabolic, spherical, or flat -sloped. If the vessel is horizontal with parabolic ends, the depth of the end. See Vessel Shape (2.7.1.1.) for an illustration. Values Range: 0.0 to 99.999 m Default: 0.0 Related Parameters Units (2.2.1.) Vessel Shape (2.7.1.1.) Vessel Dimension L (2.7.1.4.) Length of the cylindrical section of a horizontal parabolic end vessel. See Vessel Shape (2.7.1.1.) for an illustration. Values Range: 0.0 to 99.99 m Default: 0.0 Related Parameters Units (2.2.1.) Vessel Shape (2.7.1.1.) SITRANS LR250 (mA/HART) 142 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Table 1-8 (2.7.2.) Note Linearization Table must be selected in Vessel Shape (2.7.1.1.) in order for level/volume values to be transferred. If your vessel shape is more complex than any of the preconfigured shapes, you can define the shape as a series of segments. A value is assigned to each level breakpoint and a corresponding value is assigned to each volume breakpoint. Level values are defined in Units (2.2.1.). Volume units are defined by the user but are not explicitly stated in the SITRANS LR250. Level Values Range: 0.0 to span Span = High Calibration Pt. (2.3.2.) - Low Calibration Pt. (2.3.1.) Default: 0.0 Volume Values Range: 0.0 to Maximum Volume (2.7.1.2.) Default: 0.0 Enter up to 32 level breakpoints, where the corresponding volume is known. The values corresponding to 100% and 0% levels must be entered. The breakpoints can be ordered from top to bottom, or the reverse. Breakpoints are grouped into four tables: Table 1-8, Table 9-16, Table 17-24, and Table 25-32. Entering breakpoints via the handheld programmer: 1. The default unit for level values is m: to change it navigate to Setup (2.) > Sensor (2.2.) > Units(2.2.1.), and select the desired unit. 2. Navigate to Setup (2.) > Linearization (2.7.) > Maximum Volume (2.7.1.2.), and enter the value. 3. Go to the appropriate table for the particular breakpoint you wish to adjust: for example, go to Table 1-8 for breakpoint 1. 4. Under Table 1-8, go to Level 1 (2.7.2.1.) to enter the level value for the breakpoint 1. 5. Under Table 1-8, go to Volume 1 (2.7.2.2.) to enter the volume value for the breakpoint 1. 6. Repeat steps 3 to 5, until values have been entered for all required breakpoints. Level 1 (2.7.2.1.) 1. Press RIGHT arrow to open Edit mode. 2. Enter level value and press RIGHT arrow to except it. 3. Press DOWN arrow to move to corresponding volume breakpoint. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 143 Parameter reference Volume 1 (2.7.2.2.) 1. Press RIGHT arrow to open Edit mode. 2. Enter volume value and press RIGHT arrow to accept it. 3. Press DOWN arrow to move to next level breakpoint. Example (values are for example purposes only) Breakpoint Number Level value (m) Volume value (l) 500 3000 19.5 8000 Table 9-16 (2.7.3.) Table 17-24 (2.7.4.) Table 25-32 (2.7.5.) Signal Processing (2.8.) Note Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated. SITRANS LR250 (mA/HART) 144 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Near Range (2.8.1.) The range in front of the device (measured from the sensor reference point) within which any echoes will be ignored. This is sometimes referred to as blanking or a dead zone. The factory setting is 50 mm (2") past the end of the antenna, and the default is dependent on the antenna type and process connection. [See Dimension drawings (Page 209) for antenna heights.] Values Range: 0 to 20 m (0 to 65.6 ft) Default depends on antenna type and process connection: Related parameters Units (2.2.1.) Far Range (2.8.2.) Note Far Range can extend beyond the bottom of the vessel. Allows the material level to drop below Low Calibration Point without generating a Loss of Echo (LOE) state. See Sensor Mode (2.2.2.) for an illustration. Values Range: Min. = Low Calibration Pt. Max. = 23 m (75.45 ft) Default: Value for Low Calibration Pt. + 1 m (3.28 ft) Related parameters Units (2.2.1.) Use this feature if the measured surface can drop below the Low Cal. Point in normal operation. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 145 Parameter reference Propogation Factor (2.8.3.) Note • When operating in a stillpipe, values for CLEF Range (2.8.4.4.), and for the propagation factor, should be set according to the pipe size. See the table below. • For reliable results the antenna size must be close to the pipe size. Compensates for the change in microwave velocity due to propagation within a metal stillpipe instead of in free space. Values Nominal Pipe Size Range 0.3 to 1.0 depending on pipe size Default 1.0000 40 mm (1.5") 50 mm (2") 80 mm (3") 100 mm (4") Propagation Factor 0.9844 0.988 0.9935 0.9965 CLEF Range (2.8.4.4.) settings Low calibration point 700 mm (2.29 ft)b) Low calibration point 700 mm (2.29 ft)b) Low calibration point -1000 mm (3.28 ft)b) Low calibration point -1000 mm (3.28 ft)b) a) a) Since pipe dimensions may vary slightly, the propagation factor may also vary. b) CLEF range covers the whole measurement range except first 700 or 1000 mm from unit reference point (see A in graphic below) ① ② sensor reference point 700 or 1000 mm air gap ③ ④ low calibration point CLEF range 2.8.4.4. Note Flanged encapsulated antenna For Flanged encapsulated antenna (7ML5432) match the process connection size to the pipe diameter whenever possible (for example, mount a DN80/3" flange on DN80/3" pipe). SITRANS LR250 (mA/HART) 146 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Echo Select (2.8.4.) Algorithm (2.8.4.1.) Selects the algorithm to be applied to the echo profile to extract the true echo. Options tF True First echo Largest echo BLF Best of Largest and First echo Position Detect (2.8.4.2.) Defines where on the echo the distance measurement is determined. Options Center Hybrid (Center and CLEF) CLEF (Constrained Leading Edge Fit) Related parameters CLEF Range (2.8.4.4.) If the vessel bottom is being reported as the level instead of the actual material level (at low level conditions), or if the dielectric constant of the liquid to be monitored is less than 3, we recommend setting Position Detect to Hybrid and CLEF Range (2.8.4.4.) to 0.5 m (1.64 ft). Echo Threshold (2.8.4.3.) Sets the minimum echo confidence that the echo must meet in order to prevent a Loss of Echo condition and the expiration of the Fail-safe (LOE) timer. When Confidence (2.8.6.1.) exceeds Echo Threshold (2.8.4.3.), the echo is accepted as a valid echo and is evaluated. Values Range: 0 to 99 Default: 5 Related Parameters LOE Timer (2.5.2.) SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 147 Parameter reference CLEF Range (2.8.4.4.) Note CLEF Range is referenced from Far range. The CLEF algorithm is used mainly to allow correct level reporting for low dK materials which may otherwise cause an incorrect reading in an empty or almost empty vessel. It is used from Low Calibration Point (process empty level ) up to the level defined by CLEF Range (see illustration below). Above that point the Center algorithm is used. For more detail see CLEF Range (Page 258). Values Range: 0 to 20 m (0 to 65.6 ft) Default: 0.0 m Related parameters ① ② ③ Position Detect (2.8.4.2.) CLEF Range Sensor reference point Low Calibration Point (process empty level ) In applications with low dK materials we recommend setting CLEF Range to 0.5 m (1.64 ft) and Position Detect (2.8.4.2.) to Hybrid. Sampling (2.8.5.) Provides a method of checking the reliability of a new echo before accepting it as the valid reading, based on numbers of samples above or below the currently selected echo. SITRANS LR250 (mA/HART) 148 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Echo Lock (2.8.5.1.) Note Ensure the agitator is always running while SITRANS LR250 is monitoring the vessel, to avoid stationary blade detection. Selects the measurement verification process. Options Lock Off Maximum Verification (not recommended for radar) Material Agitator Total Lock (not recommended for radar) Related parameters Fill Rate per Minute (2.4.2.) Empty rate per Minute (2.4.3.) Sampling Up (2.8.5.2.) Sampling Down (2.8.5.3.) For radar applications, Material Agitator is the most often-used setting, to avoid agitator blade detection. Sampling Up (2.8.5.2.) Specifies the number of consecutive echoes that must appear above the echo currently selected, before the measurement is accepted as valid. Values Range: 1 to 50 Default: 5 Sampling Down (2.8.5.3.) Specifies the number of consecutive echoes that must appear below the echo currently selected, before the measurement is accepted as valid. Values Range: 1 to 50 Default: 2 SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 149 Parameter reference Echo Quality (2.8.6.) Confidence (2.8.6.1.) Indicates echo reliability: higher values represent better echo quality. The display shows the echo confidence of the last measurement. Echo Threshold (2.8.4.3.) defines the minimum criterion for echo confidence. Values (view only) 0 to 99 Related Parameters Echo Threshold (2.8.4.3.) ---- Shot not used Open the menu Device – Echo Profile Utilities and click on the tab Echo Profile. Echo Strength (2.8.6.2.) Displays the absolute strength (in dB above 1 μV rms) of the echo selected as the measurement echo. Values (view only) -20 to 99 ---- Shot not used Open the menu Device – Echo Profile Utilities and click on the tab Echo Profile. Noise Average (2.8.6.3.) Displays the average ambient noise (in dB above 1 μV rms) of a noise profile. Noise level is a combination of transient noise and receiving circuitry. After a measurement, the values from the previous noise shot will be displayed. TVT Setup (2.8.7.) Note Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated. SITRANS LR250 (mA/HART) 150 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Auto False Echo Suppression (2.8.7.1.) Used together with Auto False Echo Suppression Range (2.8.7.2.) to screen out false echoes in a vessel with known obstructions. A ’learned TVT’ (time varying threshold) replaces the default TVT over a specified range. See Auto False Echo Suppression (Page 259) for a more detailed explanation. Note • Make sure material level is below all known obstructions when Auto False Echo Suppression is used to learn the echo profile. (An empty or almost empty vessel is recommended.) • Note the distance to material level when Auto False Echo learns the environment. Set Auto False Echo Suppression Range to a shorter distance to avoid the material echo being screened out. • Set Auto False Echo Suppression and Auto False Echo Suppression Range during startup, if possible. • If the vessel contains an agitator it should be running. • Before adjusting these parameters, rotate the instrument for best signal (lower false-echo amplitude). SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 151 Parameter reference Before Auto False Echo Suppression ① ② ③ TVT Hover Level default TVT ④ ⑤ echo marker material level false echo 1. Determine Auto False Echo Suppression Range. Measure the actual distance from the sensor reference point to the material surface using a rope or tape measure. 2. Subtract 0.5 m (20") from this distance, and use the resulting value. 3. Go to Auto False Echo Suppression Range (2.8.7.2.) and enter the value calculated in step 2. 4. Go to Auto False Echo Suppression (2.8.7.1.) and press RIGHT arrow to open Edit Mode. 5. Select Learn. The device will automatically revert to On (Use Learned TVT) after a few seconds. SITRANS LR250 (mA/HART) 152 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference After Auto False Echo Suppression ① false echo ④ ② learned TVT ⑤ ③ Auto False Echo Suppression ⑥ Range material level default TVT echo marker To set Auto False Echo Suppression via SIMATIC PDM: Open the menu Device – Echo Profile Utilities and click on the tab Auto False Echo Suppression. For more detailed instructions see Auto False Echo Suppression via SIMATIC PDM (Page 92). To set Auto False Echo Suppression via the handheld programmer: Options OFF a) Default TVT will be used. ON ’Learned’ TVT will be used. LEARN ’Learn’ the TVTa). The learned TVT takes effect only at the next measurement. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 153 Parameter reference Auto False Echo Suppression Range (2.8.7.2.) Note Changes take effect only at the next measurement. "Master reset" does not clear the learned/stored TVT, select "Off" to turn it off or "learn" for a new TVT. See Master Reset (4.1.) Specifies the range within which Learned TVT is used [see Auto False Echo Suppression (2.8.7.1.) for more detail]. Values Range: 0.00 to 20.00 m Default: 1.00 m Related parameters Units (2.2.1.) 1. Calculate range according to Auto False Echo Suppression (2.8.7.1.) steps 1 and 2. 2. Press RIGHT arrow to open Edit mode. 3. Enter the new value and press RIGHT arrow to accept it. 4. Set Auto False Echo Suppression (2.8.7.1.). Hover Level (2.8.7.3.) Note Changes take effect only at the next measurement. Defines how high the TVT (Time Varying Threshold) is placed above the noise floor of the echo profile, as a percentage of the difference between the peak of the largest echo in the profile and the noise floor. See Auto False Echo Suppression (2.8.7.1.) for an illustration. Values Range: 0 to 100% Default: 40% When the device is located in the center of the vessel, the TVT hover level may be lowered to increase the confidence level of the largest echo. Shaper Mode (2.8.7.4.) Enables/disables the TVT shaper. Options ON OFF SITRANS LR250 (mA/HART) 154 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference TVT shaper (2.8.8.) Note • The range is –100 to 100 bits. With 2 bits per dB this gives a range of –50 to 50 dB. • Shaper Mode (2.8.7.4.) must be turned ON in order for TVT shaper points to be transferred. Adjusts the TVT (Time Varying Threshold) at a specified range (breakpoint on the TVT). This allows you to reshape the TVT to avoid unwanted echoes. There are 40 breakpoints arranged in 5 groups. (We recommend using SIMATIC PDM to access this feature.) To use TVT shaper via SIMATIC PDM: 1. Go to Level Meter > Setup > Signal Processing > TVT setup > Shaper Mode and select On. 2. Open the menu Device – Echo Profile Utilities and click on TVT Shaper. For more detail see TVT shaper via SIMATIC PDM (Page 91). To use TVT shaper via LUI (local user interface): 1. Go to Shaper Mode (2.8.7.4.) and select On. 2. Go to Breakpoint 1-9 (2.8.8.1.). 3. Open Shaper 1 and enter the TVT Offset value (between –50 and 50). 4. Go to the next Shaper point and repeat steps 3 and 4 until all desired breakpoint values have been entered. Breakpoint 1-9 (2.8.8.1.) Values Range: –50 to 50 dB Default: 0 dB Breakpoint 10-18 (2.8.8.2.) Values Range: –50 to 50 dB Default: 0 dB Breakpoint 19-27 (2.8.8.3.) Values Range: –50 to 50 dB Default: 0 dB SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 155 Parameter reference Breakpoint 28-36 (2.8.8.4.) Values Range: –50 to 50 dB Default: 0 dB Breakpoint 37-40 (2.8.8.5.) Values Range: –50 to 50 dB Default: 0 dB Measured Values (2.8.9.) Read only. Allows you to view measured values for diagnostic purposes. To access measured values via SIMATIC PDM: Open the menu View – Process Variables. Level Measurement (2.8.9.1.) The value for level. Space Measurement (2.8.9.2.) The value for space. Distance Measurement (2.8.9.3.) The value for distance. Volume Measurement (2.8.9.4.) The value for volume. Diagnostics (3.) Echo Profile (3.1.) Allows you to request the current echo profile either locally via the handheld programmer, or remotely via SIMATIC PDM, or AMS Device Manager. [For more detail see Echo Processing (Page 254)]. SITRANS LR250 (mA/HART) 156 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference To request a profile via SIMATIC PDM: Open the menu Device – Echo Profile Utilities. [For more detail see Echo Profile Utilities via SIMATIC PDM (Page 88)]. To request a profile via the handheld programmer: 1. In PROGRAM mode, navigate to Level Meter > Diagnostics (3.) > Echo Profile (3.1.) 2. Press RIGHT arrow to request a profile. [For more detail see Requesting an Echo Profile (Page 69)]. Electronics Temperature (3.2.) Current Internal Temperature (3.2.1.) Read only. Displays (in degrees C) the current temperature on the circuit board recorded by the internal electronics. For access via SIMATIC PDM open the menu View – Process Variables and check the field Electronics Temperature. Highest Value (3.2.2.) Read only. Displays (in degrees C) the maximum temperature recorded by the internal electronics. The high and low values are maintained over a power cycle. Via SIMATIC PDM navigate to Maintenance and Diagnostics > Electronics Temperature. Lowest Value (3.2.3.) Read only. Displays (in degrees C) the minimum temperature recorded by the internal electronics. The high and low values are maintained over a power cycle. Via SIMATIC PDM navigate to Maintenance and Diagnostics > Electronics Temperature. Service (4.) Note Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 157 Parameter reference Master Reset (4.1.) Note Following a reset to Factory Defaults, complete reprogramming is required. Resets all parameter to factory defaults, with the following exceptions: ● Device Address (5.1.) remains unchanged if the reset command is sent remotely (via AMS, PDM, DTM, FC375) but is reset to 0 if the reset command is sent via LUI. ● Write Protect (6.2.1.) and PIN to Unlock (6.2.2.) values are not reset. ● Auto False Echo Suppression (2.8.7.1.) learned TVT and Auto False Echo Suppression Range (2.8.7.2.) are not lost. Options Idle or Done (Return to previous menu) Factory Defaults To perform a reset to factory defaults via SIMATIC PDM, open the menu Device – Master Reset and click on Factory Defaults. SITRANS LR250 (mA/HART) 158 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Remaining Device Lifetime (4.2.) Note • Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated. • Four sets of parameters allow you to monitor the Device/Sensor Lifetimes and set up Maintenance/Service schedules, based on operating hours instead of a calendar-based schedule. See also Remaining Sensor Lifetime (4.3.), Service Schedule (4.4.), and Calibration Schedule (4.5.). • Performing a reset to Factory Defaults will reset all the Maintenance Schedule parameters to their factory defaults. • The device operates in years. To view Remaining Device Lifetime parameters in hours or days (via SIMATIC PDM only) see Lifetime (Expected) (4.2.1.). The device tracks itself based on operating hours and monitors its predicted lifetime. You can modify the expected device lifetime, set up schedules for maintenance reminders, and acknowledge them. The maintenance warnings and reminders are available through HART communications. This information can be integrated into an Asset Management system. For optimal use, we recommend that you use SIMATIC PCS7 Asset Management Software in conjunction with SIMATIC PDM. To access these parameters via SIMATIC PDM: ● Open the menu Device – Maintenance and select the Remaining Device Lifetime tab. ● After modifying values/units as required, click on Write to accept the change, and Read to view the effect of the change. ● Click on Snooze to add a year to the Total Expected Device Life. Time Units Options a) Hours; days; years Default: years a) Selectable only via SIMATIC PDM. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 159 Parameter reference Lifetime (Expected) (4.2.1.) Note The device always operates in years. Changing the units affects only the parameter view of the Service Interval parameters in SIMATIC PDM. User-configurable recommended time between product inspections. Values Units a): hours, days, years Range: 0 to 20 years Default: 10 years a) Units are selectable only via SIMATIC PDM. Time in Operation (4.2.2.) Read only. The amount of time the device has been operating. Remaining Lifetime (4.2.3.) Read only. Lifetime (Expected) (4.2.1.) less Time in Operation (4.2.2.). SITRANS LR250 (mA/HART) 160 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Activation of Reminders (4.2.4.) Note To modify this parameter via SIMATIC PDM it must be accessed via the pull-down menu Device – Maintenance. Allows you to enable a maintenance reminder. Values Timer OFF ON - no reminders checked ON - Reminder 1 (Maintenance Required) checked ON - Reminders 1 and 2 checked ON - Reminder 2 (Maintenance Demanded) checked 1. First set the values in Reminder 1 before Lifetime (Required) (4.2.5.)/ Reminder 2 before Lifetime (Demanded) (4.2.6.). 2. Select the desired Activation of Reminders option. Reminder 1 before Lifetime (Required) (4.2.5.) If Remaining Lifetime (4.2.3.) is equal to or less than this value, the device generates a Maintenance Required reminder. Values Range: 0 to Lifetime (Expected) (4.2.1.) Default: 0.164 years 1. Modify values as required. 2. Set Activation of Reminders (4.2.4.) to the desired option. Reminder 2 before Lifetime (Demanded) (4.2.6.) If Remaining Lifetime (4.2.3.) is equal to or less than this value, the device generates a Maintenance Demanded reminder. Values Range: 0 to Lifetime (Expected) (4.2.1.) Default: 0.019 years 1. Modify values as required. 2. Set Activation of Reminders (4.2.4.) to the desired option. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 161 Parameter reference Maintenance Status (4.2.7.) Indicates which level of maintenance reminder is active. In SIMATIC PDM, open the menu View – Device Status, click on the Maintenance tab, and check the Device Lifetime Status window. Acknowledge Status (4.2.8.) Indicates which level of maintenance reminder has been acknowledged. In SIMATIC PDM, open the menu View – Device Status, click on the Maintenance tab, and check the Device Lifetime Status window. Acknowledge (4.2.9.) Acknowledges the current maintenance reminder. To acknowledge a reminder via SIMATIC PDM: 1. Open the menu View – Device Status and click on the Maintenance tab. 2. In the Device Lifetime section, click on Acknowledge Warnings. To acknowledge a reminder via the handheld programmer: 1. Press RIGHT arrow twice to open parameter view and activate Edit Mode. 2. Press RIGHT arrow to acknowledge the reminder. SITRANS LR250 (mA/HART) 162 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Remaining Sensor Lifetime (4.3.) Note • Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated. • Four sets of parameters allow you to monitor the Device/Sensor Lifetimes and set up Maintenance/Service schedules, based on operating hours instead of a calendar-based schedule. See also Remaining Device Lifetime (4.2.), Service Schedule (4.4.), and Calibration Schedule (4.5.). • Performing a reset to Factory Defaults will reset all the Maintenance Schedule parameters to their factory defaults. • The device operates in years. To view Remaining Sensor Lifetime parameters in hours or days (via SIMATIC PDM only) see Lifetime Expected (4.3.1.). The device monitors the predicted lifetime of the sensor (the components exposed to the vessel environment). You can modify the expected sensor lifetime, set up schedules for maintenance reminders, and acknowledge them. To access these parameters via SIMATIC PDM: ● Open the menu Device – Maintenance and select the Remaining Sensor Lifetime tab. ● After modifying values/units as required, click on Write to accept the change, and Read to view the effect of the change. ● Click on Snooze to add a year to the Total Expected Sensor Life. ● Click on Sensor Replaced to restart the timer and clear any fault messages. Time Units Options a) Hours; days; years Default: years a) Selectable only via SIMATIC PDM. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 163 Parameter reference Lifetime (Expected) (4.3.1.) Note The device always operates in years. Changing the units affects only the parameter view of Remaining Sensor Life parameters in SIMATIC PDM. Allows you to override the factory default. Values Units a): hours, days, years Range: 0 to 20 years Default: 10.00 years a) Units are selectable only via SIMATIC PDM. SITRANS LR250 (mA/HART) 164 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Time in Operation (4.3.2.) The amount of time the sensor has been operating. Can be reset to zero after performing a service or replacing the sensor. To reset to zero: ● In SIMATIC PDM, open the menu Device – Maintenance, click on the Remaining Sensor Lifetime tab, and click on Sensor Replaced to restart the timer and clear any fault messages. ● Via the handheld programmer, manually reset Time in Operation (4.3.2.) to zero. Remaining Lifetime (4.3.3.) Read only. Lifetime (Expected) (4.3.1.) less Time in Operation (4.3.2.). Activation of Reminders (4.3.4.) Note To modify this parameter via SIMATIC PDM it must be accessed via the pull-down menu Device – Maintenance. Allows you to enable a maintenance reminder. Options Reminder 1 (Maintenance Required) Reminder 2 (Maintenance Demanded) Reminders 1 and 2 OFF 1. First set the values in Reminder 1 before Lifetime (Required) (4.3.5.)/Reminder 2 before Lifetime (Demanded) (4.3.6.). 2. Select the desired Activation of Reminders option. Reminder 1 before Lifetime (Required) (4.3.5.) If Remaining Lifetime (4.3.3.) is equal to or less than this value, the device generates a Maintenance Required reminder. Values Range: 0 to Lifetime (Expected) (4.3.1.) Default: 0.164 years 1. Modify values as required. 2. Set Activation of Reminders (4.3.4.) to the desired option. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 165 Parameter reference Reminder 2 before Lifetime (Demanded) (4.3.6.) If Remaining Lifetime (4.3.3.) is equal to or less than this value, the device generates a Maintenance Demanded reminder. Values Range: 0 to Lifetime (Expected) (4.3.1.) Default: 0.019 years 1. Modify values as required. 2. Set Activation of Reminders (4.3.4.) to the desired option. Maintenance Status (4.3.7.) Indicates which level of maintenance reminder is active. In SIMATIC PDM, open the menu View – Device Status, click on the Maintenance tab, and check the Sensor Lifetime Status window. Acknowledge Status (4.3.8.) Indicates which level of maintenance reminder has been acknowledged. In SIMATIC PDM, open the menu View – Device Status, click on the Maintenance tab, and check the Sensor Lifetime Status window. Acknowledge (4.3.9.) Acknowledges the current maintenance reminder. To acknowledge a reminder via SIMATIC PDM: 1. Open the menu View – Device Status and click on the Maintenance tab. 2. In the Sensor Lifetime section, click on Acknowledge Warnings. To acknowledge a reminder via the handheld programmer: 1. Press RIGHT arrow twice to open parameter view and activate Edit Mode. 2. Press RIGHT arrow to acknowledge the reminder. SITRANS LR250 (mA/HART) 166 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Service Schedule (4.4.) Note • Four sets of parameters allow you to monitor the Device/Sensor Lifetimes and set up Maintenance/Service schedules, based on operating hours instead of a calendar-based schedule. See also Remaining Device Lifetime (4.2.), Remaining Sensor Lifetime (4.3.), and Calibration Schedule (4.5.). • Performing a reset to Factory Defaults will reset all the Maintenance Schedule parameters to their factory defaults. • The device operates in years. To view Service Interval parameters in hours or days (via SIMATIC PDM only) see Service interval (4.4.1.). The device tracks service intervals based on operating hours and monitors the predicted lifetime to the next service. You can modify the Total Service Interval, set schedules for maintenance reminders, and acknowledge them. The maintenance warnings and reminders are communicated to the end user through status information. This information can be integrated into any Asset Management system. For optimal use, we recommend that you use SIMATIC PCS7 Asset Management Software in conjunction with SIMATIC PDM. To access these parameters via SIMATIC PDM: ● Open the menu Device – Maintenance and select the Service Schedule tab. ● After modifying values/units as required, click on Write to accept the change, and Read to view the effect of the change. ● Click on Service Performed to restart the timer and clear any fault messages. Time Units Options a) Hours; days; years Default: years a) Selectable only via SIMATIC PDM. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 167 Parameter reference Service Interval (4.4.1.) Note The device always operates in years. Changing the units affects only the parameter view of the Service Interval parameters in SIMATIC PDM. User-configurable recommended time between product inspections. Values Units a): hours, days, years Range: 0 to 20 years Default: 1.0 year a) Units are selectable only via SIMATIC PDM. Time Since Last Service (4.4.2.) Time elapsed since last service. Can be reset to zero after performing a service. To reset to zero: ● In SIMATIC PDM, open the menu Device – Maintenance, click on the Service Schedule tab, and click on Service Performed to restart the timer and clear any fault messages. ● Via the handheld programmer, manually reset Time since Last Service (4.4.2.) to zero. SITRANS LR250 (mA/HART) 168 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Time Until Next Service (4.4.3.) Read only. Service Interval (4.4.1.) less Time Since Last Service (4.4.2.). Activation of Reminders (4.4.4.) Note To modify this parameter via SIMATIC PDM it must be accessed via the pull-down menu Device – Maintenance. Allows you to enable a maintenance reminder. Options Timer OFF ON - no reminders checked ON - Reminder 1 (Maintenance Required) checked ON - Reminders 1 and 2 checked ON - Reminder 2 (Maintenance Demanded) checked 1. First set the values in Reminder 1 before Service (Required) (4.4.5.)/Reminder 2 before Service (Demanded) (4.4.6.). 2. Select the desired Reminder Activation option. Reminder 1 before Service (Required) (4.4.5.) If Time Until Next Service (4.4.3.) is equal to or less than this value, the device generates a Maintenance Required reminder. Values Range: 0 to Service Interval (4.4.1.) Default: 0.164 years 1. Modify values as required. 2. Set Activation of Reminders (4.4.4.) to the desired option. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 169 Parameter reference Reminder 2 before Service (Demanded) (4.4.6.) If Time Until Next Service (4.4.3.) is equal to or less than this value, the device generates a Maintenance Required reminder. Values Range: 0 to Service Interval (4.4.1.) Default: 0.019 years 1. Modify values as required 2. Set Activation of Reminders (4.4.4.) to the desired option. Maintenance Status (4.4.7.) Indicates which level of maintenance reminder is active. Open the menu View – Device Status, click on the Maintenance tab and check the Service Schedule Status window. Acknowledge Status (4.4.8.) Indicates which level of maintenance reminder has been acknowledged. Open the menu View – Device Status, click on the Maintenance tab and check the Service Schedule Status window. Acknowledge (4.4.9.) Acknowledges the current maintenance reminder. To acknowledge a reminder via SIMATIC PDM: 1. Open the menu View – Device Status and click on the Maintenance tab. 2. In the Service Schedule Status section, click on Acknowledge Warnings. To acknowledge a reminder via the handheld programmer: 1. Press RIGHT arrow twice to open parameter view and activate Edit Mode. 2. Press RIGHT arrow to acknowledge the reminder. SITRANS LR250 (mA/HART) 170 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Calibration Schedule (4.5.) Note • Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated. • Four sets of parameters allow you to monitor the Device/Sensor Lifetimes and set up Maintenance/Service schedules, based on operating hours instead of a calendar-based schedule. See also Remaining Device Lifetime (4.2.), Remaining Sensor Lifetime (4.3.), and Service Schedule (4.4.). • Performing a reset to Factory Defaults will reset all the Maintenance Schedule parameters to their factory defaults. • The device operates in years. To view Calibration Interval parameters in hours or days (via SIMATIC PDM only) see Calibration Interval (4.5.1.). The device tracks calibration intervals based on operating hours and monitors the predicted lifetime to the next calibration. You can modify the Total Calibration Interval, set schedules for maintenance reminders, and acknowledge them. To access these parameters via SIMATIC PDM: ● Open the menu Device – Maintenance and select the Calibration Schedule tab. ● After modifying values/units as required, click on Write to accept the change, and Read to view the effect of the change. ● Click on Calibration Performed to restart the timer and clear any fault messages. Time Units Options a) Hours; days; years Default: years a) Selectable only via SIMATIC PDM. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 171 Parameter reference Calibration Interval (4.5.1.) Note The device always operates in years. Changing the units affects only the parameter view of Remaining Sensor Life parameters in SIMATIC PDM. User-configurable recommended time between product calibrations. Values Units a): hours, days, years Range: 0 to 20 years Default: 1.0 year a) Units are selectable only via SIMATIC PDM. Time Since Last Calibration (4.5.2.) Time elapsed since last calibration. Can be reset to zero after performing a calibration. To reset to zero: ● In SIMATIC PDM, open the menu Device – Maintenance, click on the Calibration Schedule tab, and click on Calibration Performed to restart the timer and clear any fault messages. ● Via the handheld programmer, manually reset Time Since Last Calibration (4.5.2.) to zero. SITRANS LR250 (mA/HART) 172 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Time Until Next Calibration (4.5.3.) Read only. Calibration Interval (4.5.1.) less Time Since Last Calibration (4.5.2.). Activation of Reminders (4.5.4.) Note To modify this parameter via SIMATIC PDM it must be accessed via the pull-down menu Device – Maintenance. Allows you to enable a maintenance reminder. Options Timer OFF ON - no reminders checked ON - Reminder 1 (Maintenance Required) checked ON - Reminders 1 and 2 checked ON—Reminder 2 (Maintenance Demanded) checked 1. First set the values in Reminder 1 before Calibration (Required) (4.5.5.)/Reminder 2 before Calibration (Demanded) (4.5.6.). 2. Select the desired Activation of Reminders option. Reminder 1 before Calibration (Required) (4.5.5.) If Time Until Next Calibration (4.5.3.) is equal to or less than this value, the device generates a Maintenance Required reminder. Values Range: 0 to Calibration Interval (4.5.1.) Default: 0.164 years 1. Modify values as required. 2. Set Activation of Reminders (4.5.4.) to the desired option. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 173 Parameter reference Reminder 2 before Calibration (Demanded) (4.5.6.) If Time Until Next Calibration (4.5.3.) is equal to or less than this value, the device generates a Maintenance Demanded reminder. Values Range: 0 to Calibration Interval (4.5.1.) Default: 0.164 years 1. Modify values as required. 2. Set Activation of Reminders (4.5.4.) to the desired option. Maintenance Status (4.5.7.) Indicates which level of maintenance reminder is active. In SIMATIC PDM, open the menu View – Device Status, click on the Maintenance tab and check the Calibration Schedule Status window. Acknowledge Status (4.5.8.) Indicates which level of maintenance reminder has been acknowledged. In SIMATIC PDM, open the menu View – Device Status, click on the Maintenance tab and check the Calibration Schedule Status window. Acknowledge (4.5.9.) Acknowledges the current maintenance reminder. To acknowledge a reminder via SIMATIC PDM: 1. Open the menu View – Device Status and click on the Maintenance tab. 2. In the Service Schedule Status section, click on Acknowledge Warnings. To acknowledge a reminder via the handheld programmer: 1. Press RIGHT arrow twice to open parameter view and activate Edit Mode. 2. Press RIGHT arrow to acknowledge the reminder. Manufacture Date (4.6.) Read only. The date of manufacture of the SITRANS LR250 (yy mm dd). Powered Hours (4.7.) Read only. Displays the number of hours the unit has been powered up since manufacture. In SIMATIC PDM, open the menu Device – Wear. SITRANS LR250 (mA/HART) 174 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Power-on Resets (4.8.) Read only. The number of power cycles that have occurred since manufacture. In SIMATIC PDM, open the menu Device – Wear. LCD Fast Mode (4.9.) Note • LCD Fast Mode takes effect only after 30 minutes of inactivity. (Each time the device is powered up, a further 30 minutes of inactivity is required.) • LCD Fast Mode affects Measurement mode only; it has no effect on Navigation mode. Enables a faster rate of measurement from the device by disabling most of the display area. Only the bar graph will be refreshed when LCD Fast Mode is set to ON. Values ON or OFF Default: OFF LCD Contrast (4.10.) The factory setting is for optimum visibility at room temperature and in average light conditions. Extremes of temperature will lessen the contrast. Values Range: 0 (High contrast) to 20 (Low contrast). Default: 10 Adjust the value to improve visibility at room temperature and in average light conditions. Change the value in small steps to ensure you can continue to read the display. Secondary Value (4.11.) Use the secondary value to capture the menu navigation path to any viewable parameter. Once the navigation path is stored, the value of that parameter will be displayed in Measurement mode as the secondary value. While in Parameter view of the current parameter, press the decimal point key. This stores the path to the current parameter in the Secondary Value, and displays the value for that parameter on the LCD display when in Measurement mode. See The LCD Display (Page 55) for an illustration. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 175 Parameter reference Memory Test (4.12.) Allows verification of the RAM, EEPROM, and Flash memory of the SITRANS LR250. LCD Display IDLE No test in progress. BUSY Test in progress. PASS Memory test successful. FAIL Test failed. Err1 Test returned unexpected results. P Oxcafe Test passed with result data. F Oxcafe Test failed with result data. Any numeric key from 1 to 9 activates test. Handheld programmer entry to ● Press RIGHT arrow to edit then press any numeric key from 1 to 9 to activate the test. ● The reading will display BUS and then the test result text. Communication (5.) Note Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated. Device Address (5.1.) Sets the device address or poll ID on a HART network. Any address other than 0 will cause the output current to be a fixed value, and the current will not indicate the reading. Values Range: 0 to 15 Default: 0 To set Device Address via SIMATIC PDM: ● Open the project in Process Device Network View then right-click on the device. ● Go to Object Properties > Connection to access the field Short Address. SITRANS LR250 (mA/HART) 176 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Security (6.) Note Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated. Remote Access (6.1.) Access Control (6.1.1.) Note If access control is changed to limit remote access, it can only be reset via the handheld programmer. Enables/disables the read/write access to parameters via remote communications. Options Read only No changes are permitted via remote communications. Read Write Changes are permitted. Restricted Sets the status to Read only, with the potential for another HART device to change this parameter only, via remote communications. SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 177 Parameter reference Local Access (6.2.) Write Protect (6.2.1.) Note This lock affects only the handheld programmer. A remote master can change configuration if Access Control (6.1.1.) is set to allow this. Prevents any changes to parameters via the handheld programmer. Options Range: 0 to 9999 Unlock value [stored in PIN to Unlock (6.2.2.)] Lock Off Any other value Lock On ● To turn Lock On, key in any value other than the Unlock Value stored in PIN to Unlock (6.2.2.). ● To turn Lock Off, key in the Unlock Value stored in PIN to Unlock (6.2.2.). PIN to Unlock (6.2.2.) Note • Do not lose your Unlock Value: it cannot be displayed once Write Protect (6.2.1.) has been set to a different value. • Valid only for operation via the handheld programmer. • A reset to Factory Defaults will not restore the unlock value at time of shipping. Stores the value to be entered in Write Protect (6.2.1.) to unlock programming. If Write Protect (6.2.1.) is set to a different value, PIN to Unlock (6.2.2.) does not display the Unlock value. Handheld Programmer Values Range: 0 to 9999 Value when shipped: 1954. Not restored by a reset to Factory Defaults. –––– Display when Lock is on Language (7.) Selects the language to be used on the LCD. Options English Deutsch Français Español SITRANS LR250 (mA/HART) 178 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference 8.1 Alphabetical parameter list Note For a detailed list of parameters see Parameter Reference (Page 127). Maintenance Parameters are not listed below. See Remaining Device Lifetime (4.2.), Remaining Sensor Lifetime (4.3.), Service Schedule (4.4.) and Calibration Schedule (4.5.) for those parameters. 20 mA Setpoint (2.6.3.) 4 mA Setpoint (2.6.2.) Access Control (6.1.1.) Algorithm (2.8.4.1.) Analog Output Scaling (2.6.) Auto False Echo Suppression (2.8.7.1.) Auto False Echo Suppression Range (2.8.7.2.) Breakpoint 1-9 (2.8.8.1.) Breakpoint 10-18 (2.8.8.2.) Breakpoint 19-27 (2.8.8.3.) Breakpoint 28-36 (2.8.8.4.) Breakpoint 37-40 (2.8.8.5.) Calibration (2.3.) CLEF Range (2.8.4.4.) Communication (5.) Confidence (2.8.6.1.) Current Internal Temperature (3.2.1.) Current Output Function (2.6.1.) Damping Filter (2.2.4.) Device (2.1.) Device Address (5.1.) Diagnostics (3.) Distance Measurement (2.8.9.3.) Echo Lock (2.8.5.1.) Echo Profile (3.1.) Echo Quality (2.8.6.) SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 179 Parameter reference Echo Select (2.8.4.) Echo Strength (2.8.6.2.) Echo Threshold (2.8.4.3.) Electronics Temperature (3.2.) Empty Rate per Minute (2.4.3.) Fail-safe (2.5.) Fail-Safe mA Value (2.5.3.) Far Range (2.8.2.) Fill Rate per Minute (2.4.2.) Firmware Revision (2.1.2.) Hardware Revision (2.1.1.) High Calibration Pt. (2.3.2.) Highest value (3.2.2.) Hover Level (2.8.7.3.) Language (7.) LCD Contrast (4.10.) LCD Fast Mode (4.9.) Level 1 (2.7.2.1.) Level Measurement (2.8.9.1.) Linearization (2.7.) Loader Revision (2.1.3.) Local Access (6.2.) LOE Timer (2.5.2.) Low Calibration Pt. (2.3.1.) Lowest value (3.2.3.) mA Output Value (2.6.6.) Manufacture Date (4.6.) Master Reset (4.1.) Material (2.2.3.) Material Level (2.5.1.) Maximum mA limit (2.6.5.) Maximum Volume (2.7.1.2.) Measured Values (2.8.9.) SITRANS LR250 (mA/HART) 180 Operating Instructions, 08/2014, A5E32220602-AC Parameter reference Memory Test (4.12.) Menu Timeout (2.1.5.) Minimum mA limit (2.6.4.) Near Range (2.8.1.) Noise Average (2.8.6.3.) Order Option (2.1.4.) PIN to Unlock (6.2.2.) Position Detect (2.8.4.2.) Power-on Resets (4.8.) Powered Hours (4.7.) Propagation Factor (2.8.3.) Quick Start (1.) Quick Start Wizard (1.1.) Rate (2.4.) Remote Access (6.1.) Response Rate (2.4.1.) Sampling (2.8.5.) Sampling Down (2.8.5.3.) Sampling Up (2.8.5.2.) Shaper Mode (2.8.7.4.) Signal Processing (2.8.) Secondary Value (4.11.) Security (6.) Sensor (2.2.) Sensor Mode (2.2.2.) Sensor Offset (2.3.3.) Service (4.) Setup (2.) Space Measurement (2.8.9.2.) Table 1-8 (2.7.2.) Table 9-16 (2.7.3.) Table 17-24 (2.7.4.) SITRANS LR250 (mA/HART) Operating Instructions, 08/2014, A5E32220602-AC 181 Parameter reference Table 25-32 (2.7.5.) TVT Setup (2.8.7.) TVT Shaper (2.8.8.) Units (2.2.1.) Vessel Dimension A (2.7.1.3.) Vessel Dimension L (2.7.1.4.) Vessel Shape (2.7.1.1.) Volume (2.7.1.) Volume 1 (2.7.2.2.) Volume Measurement (2.8.9.4.) Write Protect (6.2.1.) SITRANS LR250 (mA/HART) 182 Operating Instructions, 08/2014, A5E32220602-AC
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : IIA SC PI 2 TP Create Date : 2014:05:21 10:54:45-04:00 Modify Date : 2014:05:21 10:55:37-04:00 Subject : Operating Instructions Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2014:05:21 10:55:37-04:00 Creator Tool : Acrobat PDFMaker 10.1 for Word Format : application/pdf Title : SITRANS LR250 (mA/HART) Description : Operating Instructions Creator : IIA SC PI 2 TP Document ID : uuid:238b4392-e50d-40d6-a91a-183137a46169 Instance ID : uuid:0f03ef4d-7c58-4af9-86e7-73b097208edc Producer : Adobe PDF Library 10.0 Page Count : 184EXIF Metadata provided by EXIF.tools