Sony Group PEGNZ90 Personal Entertainment Organizer with Bluetooth User Manual PEGA WL100

Sony Corporation Personal Entertainment Organizer with Bluetooth PEGA WL100

WLAN Users Manual

4-668-080-11 (1)Wireless LAN CardOperating Instructions 2002 Sony CorporationPEGA-WL100
2Owner’s RecordThe model number and serial number are located at the rear of theproduct. Record the model number and the serial number in the spaceprovided below. Refer to them whenever you call upon your Sonydealer regarding this product.Model Number : PEGA-WL100Serial Number : __________________For the customers in USA and Canada :NOTICEThis equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference in a residential installation.This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radiocommunications.However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determinedby turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different fromthat to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.FCC WARNINGChanges or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority to operatethe equipment.
3Declaration of ConformityTrade Name : SONYModel No. : PEGA-WL100Responsible Party : Sony Electronics Inc.Address : 1 Sony Drive, Park Ridge, NJ 07656 USATelephone No. : 201-930-6972This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.FCC Radiation Exposure Statement:This transmitter complies with FCC radiation exposure limits set forthfor an uncontrolled environment. To comply with the FCC RFexposure compliance requirements, no change to the antenna or thedevice is permitted. Any change to the antenna or the device couldresult in the device exceeding the RF exposure requirements and voiduser. In addition, this transmitter must not be co-located or operatingin conjunction with any other antenna or transmitter.The term “IC:” before the radio certification number only signifiesthat Industry Canada technical specifications were met.Operation is subject to the following two conditions: (1) this devicemay not cause interference, and (2) this device must accept anyinterference, including interference that may cause undesiredoperation of the device.L’utilisation de ce dispositif est autorisée seulement aux conditionssuivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateurdu dispositif doit être prêt à accepter tout brouillage radioélectriquereçu, même si ce brouillage est susceptible de compromettre lefonctionnement du dispositif.Continued on next page
4To prevent radio interference to the licensed service, this device isintended to be operated indoors and away from windows to providemaximum shielding. Equipment (or its transmit antenna) that isinstalled outdoors is subject to licensing.Pour empêcher que cet appareil cause du brouillage au service faisantl’objet d’une licence, il doit être utilisé à l’intérieur et devrait être placéloin des fenêtres afin de fournir un écran de blindage maximal. Si lematériel (ou son antenne d’émission) est installé à l’extérieur, il doitfaire l’objet d’une licence.This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.For the customers in European countries :Sony hereby declares that this product is in compliance with theessential requirements and other relevant provisions of EuropeanDirective 1999/5/EC.In some countries the use of the Wireless LAN Card is restricted.Before using it, make sure you read the regulation leaflet of thisproduct.Warnings•In some situations or environments, the use of the IEEE 802.11btechnology might be restricted by the proprietor of the building orresponsible representatives of the organization, for example on board ofairplanes, in hospitals or in any other environment where the risk ofinterference with other devices or services is perceived or identified asharmful.•If you are uncertain about the policy applying to the use of IEEE 802.11btechnology in a specific organization or environment, you areencouraged to first ask for authorization prior to switching it on.•Consult your physician or the manufacturer of personal medical devices(pacemakers, hearing aids, etc.) regarding any restrictions on the use ofIEEE 802.11b technology.
5•Sony, , CLIÉ, , CLIÉ GEAR, , , JogDial and Memory Stick are trademarks of Sony Corporation.•Palm OS and HotSync are registered trademarks of Palm, Inc. or itssubsidiaries. Palm Desktop and HotSync logo are trademarks of Palm, Inc. orits subsidiaries.•Microsoft, Windows and Windows NT are registered trademarks of MicrosoftCorporation in the United States and/or other countries.•Adobe and Adobe Acrobat Reader are trademarks of Adobe SystemsIncorporated.•All other names of systems, products and services are trademarks of theirrespective owners. In the manual, the TM or ® marks are not specified.Before using the PEGA-WL100, be sure to read the End User Software LicenseAgreement that accompanies it.• Copyright laws prohibit reproducing the software or the manualaccompanying it in whole or in part, or renting the software without thepermission of the copyright holder.• In no event will SONY be liable for any financial damages, or loss ofprofits, including claims made by third parties, arising out of the use of thesoftware supplied with this unit.• If a problem occurs with this product as a result of defectivemanufacturing, SONY will replace it. However, SONY bears no otherresponsibility.• The software provided with this unit cannot be used with other units.• Please note that, due to continued efforts to improve quality, the softwarespecifications may be changed without notice.• Operation of this unit with software other than that provided is notcovered by the warranty.
6Table of ContentsIntroduction ................................................................................................... 7Names of Parts .............................................................................................. 9Inserting/Removing the Wireless LAN Card ........................................ 10Installing the Software ............................................................................... 12Performing Communications via a Wireless LAN Access Point(Infrastructure Mode) .............................................................................. 14Basic Settings ..................................................................................... 14Advanced Settings ............................................................................ 20Connecting your CLIÉ Handheld to a Wireless LAN ........................... 21Performing Communications Directly between your CLIÉ Handheldand Another Device on a Wireless LAN (Ad-Hoc Mode) ................. 23Basic Settings ..................................................................................... 23Connecting your CLIÉ Handheld to Another Device on aWireless LAN ................................................................................. 30Performing a HotSync Operation via a Network with a WirelessLAN Card ................................................................................................. 32Troubleshooting .......................................................................................... 34Precautions on Use ..................................................................................... 37Specifications ............................................................................................... 38
7IntroductionThis product is a Wireless LAN Card for the Sony PersonalEntertainment Organizer (mentioned as CLIÉ handheld after this) ofthe Palm OS 5 (ver5.0).This product complies with IEEE 802.11b* and allows you to accessthe Internet wirelessly in locations where there is a Wi-Fi certifiedwireless LAN access point.* Wi-Fi certified.Performing a HotSync operationYou can perform a HotSync operation via a network (synchronizedata wirelessly) between your CLIÉ handheld and a personalcomputer. For details on HotSync operation, see the OperatingInstructions of your CLIÉ handheld.PEGA-WL100 and CLIÉ handheld Personal computerLAN access pointContinued on next page
8Accessing the InternetYou can access the Internet from your CLIÉ handheld in which thisWireless LAN card is inserted through a LAN access point, and enjoybrowsing various websites or sending/receiving email.Notes•To access the Internet through a LAN access point, you need to be a subscriberto a telecommunications company and an Internet Service Provider (ISP) inadvance.•You may need a personal computer to set a wireless LAN. For details, see theOperating Instructions of your wireless LAN access point.PEGA-WL100and CLIÉhandheldInternetLAN access point
9Names of PartsWireless LAN CardFrontRearOther items includedCD-ROM (1)Hard case (1)Operating Instructions (1)Warranty card (1)End-User’s License Agreement (1)LED indicatorBlinks slowly while your CLIÉhandheld is connected to an accesspoint, etc.Blinks rapidly during data transfer.(Flashing speed varies depending onthe amount of data being transferred).Does not blink when your CLIÉhandheld is not connected to an accesspoint, etc.MAC AddressThis address may be used by yourSystem Administrator.
10Inserting/Removing the Wireless LANCardInserting the Wireless LAN card in your CLIÉhandheldInsert the Wireless LAN card in Wireless Communication Slot of theCLIÉ handheld.Notes•Insert the Wireless LAN card straight in Wireless Communication Slot of theCLIÉ handheld.•Do not insert the Wireless LAN card in the wrong way. Forcing it in thewrong way will damage it and cause a malfunction.•You may be unable to use the Wireless LAN card when the remaining powerof the battery in the CLIÉ handheld is low. Before using, charge the batteryfully.Insert the Wireless LAN cardall the way into the slot untilit fully mates with theconnector.
11Removing the Wireless LAN card from your CLIÉhandheldAfter use, terminate communications. Then, pull the wireless LANcard up straight.When using this Wireless LAN card with aFlip&Rotate style CLIÉ handheldDo not rotate the display when the wireless LAN card is inserted inthe Wireless Commnunication Slot of the CLIÉ handheld. This maypress the display panel against the Wireless LAN card and cause amalfunction.NoteDuring communication, do not remove the Wireless LAN card or subject theCLIÉ handheld to excessive shock.
12Installing the SoftwareWhen you try to perform wireless LAN communications for the firsttime after inserting the Wireless LAN card in your CLIÉ handheld,you need to install the Wireless LAN utility in your CLIÉ handheld.You can install the Wireless LAN utility by using the supplied CD-ROM.NoteBefore installation, it is necessary to have Palm Desktop for CLIÉ installed andto perform a HotSync operation. Connect the CLIÉ handheld to a Windowscomputer, using a cradle, etc. For details on how to connect the CLIÉ handheldto the computer, see the Operating Instructions of your CLIÉ handheld.1Perform a soft reset on your CLIÉ handheld.For details on how to perform a soft reset, see the OperatingInstructions of your CLIÉ handheld.2Insert the supplied CD-ROM in the CD-ROM drive ofyour Windows computer.The installer starts and the initial screen appears.TipIf the installer does not start automatically, double-click [setup] (setup.exe)which can be found in the CD-ROM.3Proceed with the installation, following the installer’sinstructions.On the user name selection screen, select a user’s name.NoteIf you want to use more than one CLIÉ handheld, you need to install thisutility in each CLIÉ handheld.
134Click [Done] when the installer-closing screen appears.Your computer is ready to install the Wireless LAN utility to yourCLIÉ handheld. In the next step, you will perform a HotSyncoperation to carry out the installation.5Click the icon on the task tray that is located in thelower right corner of the Windows display on yourcomputer.Check that [Local USB] is ticked in the shortcut menu on thedisplay.TipIf you cannot find the icon on the task tray, click [Programs] ([AllPrograms] in Windows® XP), [Sony Handheld], and then [HotSyncManager] to start up the HotSync manager, from the [Start] menu.6Execute a local HotSync operation on your CLIÉhandheld.The Wireless LAN utility is installed into your CLIÉ handheld.NotePart of this software application extends into the system of CLIÉ handheld.Therefore, it cannot be uninstalled.After you perform a hard resetBe sure to reinstall this utility.After a hard reset, normally, the backup data in a personal computeris automatically restored to your CLIÉ handheld through a HotSyncoperation. However, this utility restores only the setting file when aHotSync operation is performed, and it does not restore the utilityitself. Therefore, it is necessary to reinstall this utility after a hardreset.
14Performing Communications via aWireless LAN Access Point(Infrastructure Mode)You can wirelessly access the Internet or perform communicationswith other communication device through a wireless LAN accesspoint.Basic SettingsBefore settingYou first need to input a couple of values to set the wireless LAN access pointyou use. Check the following values in advance.[NetworkID (SSID)]: It is also called ESS-ID or Network Name.[WEP (Wired Equivalent Privacy)]: It is also called Encryption.For details, ask your System Administrator. When you have a wireless LANaccess point for your personal use, refer to the operating instructions of thewireless LAN access point.NoteThe Wireless LAN card uses the 1-11 channels (2.4 GHz band of frequencies). Ifyour access point uses the 12-14 channels, it is impossible to performcommunications using the Wireless LAN card.1Insert the Wireless LAN card in WirelessCommunication Slot of your CLIÉ handheld.2Tap the [Prefs] icon on the home screen of your CLIÉhandheld.The [Preferences] screen appears.3Tap V in the upper right corner of the screen, andselect [Network].The [Network] screen appears.
154Tap V of [Service], and select [Wireless LAN].5Tap [Details...] in the lower left corner of the screen.The [Wireless LAN Setup] screen appears.6Tap [Create].A new input screen of [Wireless LAN Setup] appears.Check that [Infrastructure] is selected (highlighted) in[ConnectMode]. If it is not selected, tap [Infrastructure] to select it.Continued on next page
16TipTapping the mark in the upper right corner of the screen shows a briefexplanation for the setting.7Enter a profile name in [ProfileName].Specify a name freely according to the name of the othercommunication device, access point, etc.8Enter a network ID in [NetworkID (SSID)].Network ID (SSID) is fixed on the part of the access point you use.Be sure to enter the network ID (SSID) that is specified by youraccess point.NoteNetwork ID is case-sensitive between capital letters and small letters. Be carefulwhen entering a Network ID.
179Select the encryption level in [WEP].WEP (encryption level) is fixed depending on the access point youuse. Be sure to select the encryption that is used by your accesspoint.TipWhen you select [None] in [WEP], you do not need to enter a WEP key. Inthis case, skip the next step, and go to Step 11.10Enter a WEP key.The WEP key is fixed, depending on the access point you use. Besure to enter the WEP key that is specified by your access point.Continued on next pageb
18When you select 40/64bit: alphanumeric string (5 characters)Enter a 5-digit password using alphabet (a-z), numbers (0-9) andsymbols.When you select 40/64bit: hexadecimal notation (10 figures(Hex))Enter a 10-digit password using alphabet (a-f) and numbers(0-9).When you select 104/128bit: alphanumeric string (13 characters)Enter a 13-digit password using alphabet (a-z), numbers(0-9) and symbols.When you select 104/128bit: hexadecimal notation (26 figures(Hex))Enter a 26-digit password using alphabet (a-f) and numbers(0-9).NoteWEP key distinguishes between capital letters and small letters. Be carefulwhen entering a WEP key.Tips•WEP key is the function that encrypts data that are to be sent by radiowaves.•Depending on the manufacturer, the above WEP keys may be assigned adifferent name.11Tap [OK].The basic settings are completed by the profile name you set inStep 7.12Tap the Home icon on your CLIÉ handheld.The home screen appears.
19Modifying the settings1Tap the [Prefs] icon on the home screen of your CLIÉ handheld.The [Preferences] screen appears.2 Tap V in the upper right corner of the screen, and select[Network].The [Network] screen appears.3 Tap V of [Service], and select [Wireless LAN].4Tap [Details...] in the lower left corner of the screen.The [Wireless LAN Setup] screen appears.5 Tap V below [ProfileName], and select the profile name youwant to modify.6Tap [Edit] at the bottom of the screen.The [Wireless LAN Setup] input screen appears.7Modify the settings.8Tap [OK].9Tap the Home icon.The home screen appears.Deleting the profile you have set1In Step 6 of “Modifying the settings” above, tap [Delete] at thebottom of the screen.The selected profile is deleted.2Tap [OK].3Tap the Home icon.The home screen appears.NoteDo not modify the settings while the Wireless LAN card is being connected tothe wireless LAN access point.
20Advanced SettingsSetting a network manuallyWhen it is necessary to set a network IP address or DNS address,follow the procedure below.1Tap [Advanced Setup] in the lower right corner of the[Wireless LAN Setup] input screen.2Tap the checkbox of [Auto] in [IP Address] or [DNSAddress], and remove the tick.The IP Address input screen or the DNS Address input screen appears.3Enter necessary addresses.4Tap [OK] when you complete the setting.Disabling the power saving mode1 Tap [Advanced Setup] in the lower right corner of the [WirelessLAN Setup] input screen.2Tap the checkbox of [Enable] in [PowerSaveMode], and removethe tick.The power saving mode is disabled.TipWhen the communication conditions are not good, you can disable thepower saving mode to maximize the battery power and achieve bettercommunications. However, it will make the battery life shorter.Normally, the power saving mode is recommended.
21Connecting your CLIÉ Handheld to a Wireless LAN1Insert the Wireless LAN card in WirelessCommunication Slot of your CLIÉ handheld.2Tap the [Prefs] icon on the home screen of your CLIÉhandheld.The [Preferences] screen appears.3Tap V in the upper right corner of the screen, andselect [Network].The [Network] screen appears.4Tap V of [Service], and select [Wireless LAN].TipIf you have set only one profile, go to Step 8.Continued on next page
225Tap [Details...] in the lower left corner of the screen.The [Wireless LAN Setup] screen appears.6Tap V below [Profile Name], and select the profilename you want to use.7Tap [OK].The [Preferences] screen appears again.8Tap [Connect] at the bottom of the screen.Your CLIÉ handheld begins to connect to a wireless LAN.When a connection is established, start up the application youlike.
23Performing Communications Directlybetween your CLIÉ Handheld andAnother Device on a Wireless LAN(Ad-Hoc Mode)Your CLIÉ handheld can communicate directly with another deviceon a wireless LAN without using a wireless LAN access point.The Ad-hoc mode settings and communications require network knowledge.Basic Settings1Insert the Wireless LAN card in WirelessCommunication Slot of your CLIÉ handheld.2Tap the [Prefs] icon on the home screen of your CLIÉhandheld.The [Preferences] screen appears.3Tap V in the upper right corner of the screen, andselect [Network].The [Network] screen appears.4Tap V of [Service], and select [Wireless LAN].Continued on next page
245Tap [Details...] in the lower left corner of the screen.The [Wireless LAN Setup] screen appears.6Tap [Create].A new input screen of [Wireless LAN Setup] appears.TipTapping the mark in the upper right corner of the screen shows a briefexplanation for the setting.7Enter a profile name in [ProfileName].Specify a name freely according to the name of the othercommunication device, access point, etc.
258Enter a network ID in [NetworkID (SSID)].Specify an alphanumeric string freely. The same network ID(SSID) needs to be entered in both your CLIÉ handheld and theother communication device.9Select the encryption level in [WEP].Be sure to select the same encryption level for both your CLIÉhandheld and the other communication device.TipWhen you select [None] in [WEP], you do not need to enter a WEP key. Inthis case, skip the next step, and go to Step 11.Continued on next page
2610Enter a WEP key.Be sure to enter the same WEP key in both your CLIÉ handheldand the other communication device.For details on WEP key, see pages 17-18.11Tap [Adhoc] in [ConnectMode].The Ad-hoc mode is selected as the connection type.b
2712Tap V of [ch] below [Adhoc], and select a channel.Be sure to select the same channel for both your CLIÉ handheldand the other communication device. Select a channel from 1 to11.13Tap [Advanced Setup] in the lower right corner of thescreen.14Tap the checkbox of [Auto] in [IP Address], and removethe tick.The IP address input screen appears.NoteAd-hoc mode may not be established if “Auto” is checked.The connection works only when both of the PC without DHCP and CLIÉhandheld select “Auto”. Most of the time, user has to enter static IP on CLIÉhandheld for the Ad-hoc mode.Continued on next page
2815Enter an IP address and a sub-netmask.Enter different IP addresses in your CLIÉ handheld and the othercommunication device.Enter the same Subnet mask in your CLIÉ handheld and the othercommunication device.(Eg.)IP address CLIÉ handheld: 192.168.0.1Other device: 192.168.0.2Subnet mask CLIÉ handheld/other device:255.255.255.0TipEnter a gateway address if necessary. When it is necessary to enter a DNSaddress, tap and tick the checkbox of [Auto] in [DNS Address] beforeentering the DNS address.16Tap [OK].The [Wireless LAN Setup] screen appears.17Tap [OK].The settings are completed in the profile name you set in Step 7.18Tap the Home icon on your CLIÉ handheld.The home screen appears.NoteUser has to find the Subnet mask from thePC that he/she wants to connect to. Thefollowing is referred to find Subnet mask ona PC.Windows 98 and Windows ME:From [Start] c [Run...] c type in ‘winipcfg’ cthe [IP configuration] dialog box appears ccheck the IP address and Subnet mask.Windows 2000 and Windows XP:From [Start] c [Run...] c type in ‘cmd’ c type‘ipconfig/all’ c check the IP address andSubnet mask.
29Modifying the settings1Tap the [Prefs] icon on the home screen of your CLIÉ handheld.The [Preferences] screen appears.2 Tap V in the upper right corner of the screen, and select[Network].The [Network] screen appears.3 Tap V of [Service], and select [Wireless LAN].4Tap [Details...] in the lower left corner of the screen.The [Wireless LAN Setup] screen appears.5 Tap V below [ProfileName], and select the profile name youwant to modify.6Tap [Edit] at the bottom of the screen.The [Wireless LAN Setup] input screen appears.7Modify the settings.8Tap [OK].9Tap the Home icon.The home screen appears.Deleting the profile you have set1In Step 6 of “Modifying the settings” above, tap [Delete] at thebottom of the screen.The [Delete Profile] confirmation dialog window appears.2Tap [OK] to confirm deletion or [Cancel] to cancel the deletion.3Tap the Home icon.The home screen appears.NoteDo not modify the settings while the Wireless LAN card is being connected tothe wireless LAN access point.Continued on next page
30Connecting your CLIÉ Handheld to Another Deviceon a Wireless LAN1Insert the Wireless LAN card in WirelessCommunication Slot of your compatible CLIÉ handheld.2Tap the [Prefs] icon on the home screen of your CLIÉhandheld.The [Preferences] screen appears.3Tap V in the upper right corner of the screen, andselect [Network].4Tap V of [Service], and select [Wireless LAN].TipIf you have set only one profile, go to Step 8.
315Tap [Details...] in the lower left corner of the screen.The [Wireless LAN Setup] screen appears.6Tap V below [Profile Name], and select the profilename you want to use.7Tap [OK].The [Preferences] screen appears again.8Tap [Connect] at the bottom of the screen.Your CLIÉ handheld begins to connect to a wireless LAN.When a connection is established, start up the application you like.
32Performing a HotSync Operation via aNetwork with a Wireless LAN CardThis Wireless LAN card can be used in various ways. For example,you can perform a HotSync operation with a Windows computer via awireless LAN. Follow the procedures below.Preparing your computer1Click the icon in the Windows task tray (bottom-right cornerof the taskbar) and select [Network] from the shortcut menu.2Click the icon in the Windows task tray again and select[Setup] from the shortcut menu.The [Setup] screen is displayed.3Click the [Network] tab, then click the check box next to theuser name for HotSync.4Click [TCP/IP Settings], and enter a Subnet Mask.5Click [OK].6Connect your CLIÉ handheld to your computer, and perform aHotSync operation.The computer information is transferred to your CLIÉ handheld.When you perform a HotSync operation via a wireless LAN, yourCLIÉ handheld identifies the computer based on the informationtransferred.Preparing your CLIÉ handheldFollow the steps below to set up your CLIÉ handheld for a HotSyncoperation via a wireless LAN.1Select [Wireless LAN] in [Service] on the [Network] screen of[Preferences], and select a profile name for a HotSync operationon the [Wireless LAN details] screen.For details, see the Steps 1 to 6 of “Connecting your CLIÉ Handheldto a Wireless LAN” on pages 21 and 22.
332Rotate the Jog Dial navigator to select HotSync and press theJog Dial navigator on the Application Launcher screen.The [HotSync] screen is displayed.You can also tap the [HotSync] icon to display the HotSync screen.3Tap the Menu icon, and tap [Primary PC Setup] from the[Option] menu.4Check that correct data is entered in [Primary PC Address] and[Subnet Mask(optional)], and tap [OK].5Tap the Menu icon, and tap [Modem Sync Prefes] from the[Option] menu.6Tap [Network], and tap [OK].7When the HotSync screen appears, tap [Modem], and then tap[Select Service].8 Tap V of [Service], select [Wireless LAN], and tap [Done].TipIt is unnecessary to enter a telephone number in [Enter phone #].NoteIt is also necessary to select [Wireless LAN] in [Service] on the [Network] screenof the [Preferences] that can be started from the home screen.Performing a HotSync operationWhen you finish the preparation of your CLIÉ handheld and yourcomputer, tap the [HotSync] icon on the [HotSync] screen.Your CLIÉ handheld automatically connects to the network andbegins a HotSync operation.When communication is not possibleFollowing the above Step 3, erase the [Primary PC Name].
34TroubleshootingIf any problem occurs, for example, if communication is not possible,or if the unit does not operate normally, please check the points listedin this troubleshooting guide.Visit Sony CLIÉ support website:Customers in USA, Canada and Mexico:http://www.ita.sel.sony.com/support/clie/access/Customers in European Countries:http://www.clie-link.com/Customers in Asia-Pacific Countries:http://vaio-online.sony.com/clie/If the problem persists, contact the Sony dealer where you purchasedthis product or a Sony service representative serving your area.SymptomYour CLIÉ handhelddoes not recognize thisWireless LAN card.(Although connectionhas started, the LEDindicator on theWireless LAN carddoes not flash.)You cannot connectyour CLIÉ handheld toan access point.Cause/Remedy•The Wireless LAN card is not installedcorrectly in your CLIÉ handheld.pInsert the Wireless LAN card intoWireless Communication Slot of yourcompatible CLIÉ handheld in thecorrect way until it fully mates with theconnector.•A service other than [Wireless LAN] isselected in the [Network] of [Preferences].pSelect [Wireless LAN] in [Service].•A wrong profile is selected.pCheck the [Profile Name] you haveselected on the [Wireless LAN Setup]screen.•The settings for communications are notcorrect.pCheck the settings of Network ID, WEPkey, etc.
35SymptomYou cannot connectyour CLIÉ handheld toan access point.You cannot access theInternet.The data transfer rate isslow.Cause/Remedy•Your CLIÉ handheld and the access pointare placed too far apart.pDecrease the distance between them.•There is an obstacle that could block offradio waves (e.g., metal plate, concreteblock) between your CLIÉ handheld andthe access point.pMove your CLIÉ handheld and/or theaccess point to different places.pDisable the power saving mode.(This will increase the powerconsumption. Be careful of theremaining battery power).•The channels of the access point are not setat 1-11.pChange the channel setting of the accesspoint.•The access point you are using is notconfigured for internet access.pConnect the access point to the Internet,following the operating instructions ofthe access point.•There is a mistake in the Network settings.pAsk your System Administrator aboutthe settings.•Some other access points are interferingwith communication.pChange the channel number of theaccess point you are using. For detailson how to change the setting, see theOperating Instructions of your accesspoint.•The access point is being heavily used.pWait a while and try access again.Continued on next page
36SymptomThe data transfer rate isslow.You forget a WEP(encryption) key.You cannot send orreceive email.You cannot perform aHotSync operation.You cannot browsehomepages.Cause/Remedy•There is an obstacle that could block offradio waves (e.g., metal plate, concreteblock) between your CLIÉ handheld andthe access point.pMove your CLIÉ handheld and/or theaccess point to a different place.pDisable the power saving mode.(This will increase the powerconsumption. Be careful of theremaining battery power).•There is a device operating at the 2.4 GHzband of frequencies (microwave oven,Bluetooth-enabled device, etc.) aroundthe CLIÉ handheld.pIncrease the distance between thedevice and the CLIÉ handheld or turnoff the power of the device.pAfter changing all the settings of theaccess point to its factory default setting,set the access point again.To restore the default settings, see theoperating instructions of the access point.pCheck the settings of the emailingsoftware you are using.For details on how to set the emailingsoftware, see its operating instructions.pCheck the settings of HotSync.For details on how to set HotSync, see theoperating instructions supplied with yourCLIÉ handheld.pCheck the settings of the web browseryou are using.For details on how to set the webbrowser, see its operating instructions.TipYou can view the data of the communication preferences.While performing communications using your CLIÉ handheld in which thisWireless LAN card is inserted, show the [Network] screen of [Preferences].Select [Option] on the menu, then select [View Log].
37Precautions on UseHandling this Wireless LAN Card•Do not subject the card to excessive shock, and take care not to dropit to prevent malfunction.•Do not use or store this unit in locations subject to:- extremely high temperature, such as in direct sunlight or near aheater.- excessive dust- high humidity- vibrations- poor ventilationIt may cause a malfunction.•Do not use the card in a shaky, unstable place.•Do not put a metal object such as a metal clip etc. inside the card.•When inserting the card in the CLIÉ handheld, take care not to forceit in the wrong way. It may cause a malfunction.•When there is a device operating at the 2.4 GHz band of frequenciesaround the CLIÉ handheld, the card and the CLIÉ handheld may notwork correctly.CondensationCondensation is a phenomenon that occurs when moisture in the airbecomes water drops when it contacts a metal plate etc. Condensationmay occur on the surface or inside of the Wireless LAN Card onoccasions when you quickly move it from a cold place to a warmplace, when you turn on the heater in the room on a cold, wintermorning. Using the Wireless LAN Card with condensation on it maycause a malfunction. If condensation occurs on the Wireless LANCard, leave it without turning on the power of the CLIÉ handhelduntil the condensation disappears.
38SpecificationsPower sourcePowered by CLIÉ handheldPower consumptionWhen transmitting: Approx. 560 – 920 mW (typ)*Idle: Approx. 90 mW (typ)**At the default setting(Note: The Wireless LAN card consumes no electricity when the LEDindicator is off.)DimensionsApprox. 1 11/16 × 2 1/4 × 1/4 in. (width/length/thickness)(42.8 × 55.4 × 5.9 mm)MassApprox. 0.5 oz (14 g)Maximum communication range1)Indoor: 300 ft. (90 m)Outdoor: 1000 ft. (300 m)Supported protocolTCP/IPApplied standardIEEE 802.11bFrequency band2.4 GHz band (1 – 11 channels, ISM band)WEP (data encryption)128-bit/40-bitModulation methodDS-SS (in conformity to IEEE 802.11b)Operating temperature41 ˚F – 95 ˚F (5 ˚C – 35 ˚C)1) Actual range will vary depending on factors such as obstacles betweendevices, magnetic fields around a microwave oven, static electricity,interference, radio wave conditions, reception sensitivity or antennaperformance, or the operating system or software application, etc.Design and specifications are subject to change without notice.
Printed in JapanPrinted on 100% recycled paper usingVOC (Volatile Organic Compound)-freevegetable oil based ink.Customer SupportFor the latest support information,check our official Sony CLIÉ Web siteCustomers in USA, Canada and Mexico:http://www.ita.sel.sony.com/support/clie/access/Customers in European Countries:http://www.clie-link.com/Customers in Asia-Pacific Countrieshttp://vaio-online.sony.com/clie/

Navigation menu