TOSHIBA TEC Singapore S-0601 Dot Printer User Manual 5

Download:
Mirror Download [FCC.gov]
Document ID	650719
Application ID	RW2UU6hYTW7Ypz4db7u4mQ==
Document Description	Users Manual 5
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.43kB (192896 bits)
Date Submitted	2006-04-25 00:00:00
Date Available	2006-04-20 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	GNU Ghostscript 7.06
Document Lastmod	0000-00-00 00:00:00
Document Title	Microsoft Word - Ch-2-3 Paper Handling Rev C2_b.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	2328

Selecting Paper
The printer can handle either single sheets or continuous forms. Single sheets, also called
cut sheets, include envelopes and non-continuous, multipart forms. Continuous forms
include labels and multipart forms fed into the printer using the forms tractors.
For best results, use paper that meets the specifications listed in the following table. (See
Appendix B, “Printer and Paper Specifications,” for detailed specifications.) If you are unsure
of the suitability of a particular type of paper, try testing the paper or consult your dealer.
Paper Specifications
Paper Size
Parameter
Width -- Cut Sheet
Width -- Fan-Fold
Length
Thickness
Fixed Unit
102 to 267 mm
102 to 216 mm
102 mm or greater
Up to 0.35 mm
Portable Unit
102 to 248 mm
102 to 216 mm
102 to 279 mm
Up to 0.35 mm
Paper Thickness and Number of Copies
Thickness
Copies
Description
0.35 mm (0.014 in) maximum total thickness.
1 to 3 copies, including the original.
For carbon-interleaved paper, the carbon counts as
a copy.
Overview of Paper Operations
The following levers and buttons are used in paper handling:
Lift the cover to locate these levers inside the printer.
• Print Gap lever on the left side under the cover
• Paper Select lever on the right side under the cover
The following figure shows the location of each lever, indicators, and buttons:
Print Gap Lever
Paper Select Lever
• All buttons on the control panel for primary and alternative functions are labeled
below and above respectively.
Control
Buttons
Control
Panel
Indicator
Lights
Printer Controls and Buttons
The following table summarizes the use of levers and buttons in paper handling. More
detailed information is provided later in this chapter.
Caution:
To load or feed paper, the printer must be:
• In the Ready state but not receiving or printing data
• In the Pause state
Levers and Buttons Used for Paper Handling
Lever/Button
Purpose
FF/LOAD
Form Feed
Action
Press FF/LOAD to execute a form feed.
Continuous forms are fed forward by one page.
Single sheets are ejected.
Load paper
Press FF/LOAD to feed paper to the top of form
position.
PARK
Unload forms
Press PARK to retract continuous forms to the
“park position.”
SETUP/EXIT + ALT
Press SETUP/EXIT and ALT at the same time to
Enter Top-of-Form enter TOF Adjustment mode where the paper
(TOF) Adjustment loading position can be adjusted.
mode
See Top-of-Form Adjustment later in this chapter.
Paper select lever * Select paper path Move the paper select lever forward for
continuous sheets.
Move the paper select lever backward for single
forms.
Print Gap Lever
Adjust for paper
thickness or
number of copies
Select the number corresponding to the number
of copies (including the original). Vary the setting
upward or downward to optimize printing.
* The following graphics are engraved on the casing.
Continuous Forms
Single Sheet
The printer can handle paper with different thicknesses, including multipart forms with up to
four parts (original plus three copies). For details on paper thickness specifications, see
Appendix B “Printer and Paper Specifications.”
The Print Gap lever, located on the left under the cover, allows you to adjust for different
paper thicknesses. Be sure to adjust the Print Gap lever whenever you change the number
of copies being printed.
The print gap lever has twelve settings.
Moving the Print Gap lever to front of printer reduces the Print Gap.
Adjusting the Print Gap Lever
Small Print Gap
Large Print Gap
Rear of Printer
Left Side View
Front of Printer
Important:
Open Print Gap
lever to maximum
to replace ribbon.
Caution: If printing smears, the ribbon misfeeds, or the paper jams, move the lever one position wider.
Using Continuous Forms
Continuous forms paper, fanfolded at the horizontal perforations, is ideal for printing rough
drafts, long files, forms and invoices. The paper is fed into the printer using the forms tractor
unit. The Push tractor is at the front/bottom of the printer. The paper is loaded and adjusted
via pushbuttons. The forms may be advanced to tear off position by operator or automatically
through a timeout.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 4
Producer                        : GNU Ghostscript 7.06
Title                           : Microsoft Word - Ch-2-3 Paper Handling Rev C2_b.doc
Creator                         : PScript5.dll Version 5.2
Create Date                     : 4/4/2006 13:27:33
Author                          : 2328

EXIF Metadata provided by EXIF.tools