TOSHIBA TEC Singapore S-0601 Dot Printer User Manual 4

Download:
Mirror Download [FCC.gov]
Document ID	650718
Application ID	RW2UU6hYTW7Ypz4db7u4mQ==
Document Description	Users Manual 4
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	12.85kB (160617 bits)
Date Submitted	2006-04-25 00:00:00
Date Available	2006-04-20 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	GNU Ghostscript 7.06
Document Lastmod	0000-00-00 00:00:00
Document Title	Microsoft Word - Ch-2-2 Paper Handling Rev C2_b.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	2328

Rear
Front
Left Side View
1. Power Switch
2. Cover Latch (to secure top cover)
3. Forms Tractors (to hold and feed continuous forms)
4. Paper Guides (to guide single sheets)
5. Paper Exit Slot and Tear Edge
6. Top Cover – Rear
7. Single Sheet Tray (Shown in down Position)
Bottom View
8. Interface Connectors (or Wireless Adapters if installed)
Vertical Position
Bottom View
Operations of the Control Panel
This section summarizes status indications and operations of the control panel in Normal
mode. For details on Set-Up mode, see Chapter 4, “Using Set-Up Mode.”
Normal mode operation includes everyday operations, such as paper handling, font
selection, macro selection, and protocol selection. The first table lists basic states
represented by the Ready and Fault indicators. The second table lists Normal mode
operations and required user response. Operations are listed by functions.
Basic States of the Printer
Indicator
Status
Printer Status
Ready
On
The printer is ready for printing
or
The printer is receiving or printing data.
Blinking
The printer is not ready and holds printing
data.
Off
The printer is not ready and it does not hold
printing data.
On
The printer is out of paper.
Blinking slowly
The printer has detected an operational error:
paper jam, interface error, carriage error,
paper unloading error, etc.
Blinking fast
The printer detected diagnostic errors at
power-up.
Fault
Operation
Required Conditions *1
Ready
Printing *2
Required Action
Fault
Load continuous forms paper —
Not printing
On
Press FF/LOAD.
Load single sheet paper
—
Not printing
On
Paper is automatically detected
and advanced (auto-loading)
when it is first inserted. In this
mode, if the FF button is
pushed, the inserted sheet will
be ejected from the printer and
the Fault LED will light,
indicating paper out condition.
Feed paper a page
—
Not printing
Off
Press FF/LOAD.
Advance perforation to tear —
bar
Eject single-sheet paper
—
Not printing
Off
Press READY.
Not printing
Off
Unload continuous-forms
paper *3
—
Not printing
Off
Press FF/LOAD. The Fault LED
will light, indicating a paper out
condition.
Press Park.
Pause printing
On
Printing
Off
Press READY
Resume printing
Blinking Not printing
Off
Press READY
Resume printing after a fault Off
Not printing
On
Clear error and press READY.
Resume printing after paper Off
out
Place printer in Ready state Off
Not printing
On
Load paper.
Not printing
Off
Press READY
Place printer in pause state
On
—
Off
Press READY
Enter Normal mode
N/A
N/A
N/A
Printing test
N/A
N/A
N/A
Turn power on without pressing
any buttons
Turn power on while pressing
FF/LOAD button.
Operation
Required Conditions *1
Required Action
Ready Printing *2
Fault
Enter Top-of-Form Adjustment mode—Not printing
Off
Press SETUP/EXIT and ALT.
Use the adjustment temporarily
Off
—
Off
Press ALT-NEXT.
Use the adjustment permanently
Off
—
Off
Press SETUP/EXIT.
Clear the adjustment
Off
—
Off
Press ALT-PREVIOUS.
Enter Set-Up mode
N/A
N/A
N/A
Turn power on while pressing
SETUP/EXIT.
Move cursor to select
Off
Not printing
Off
Press NEXT or PREVIOUS
button.
Off
Not printing
Off
Press NEXT or PREVIOUS
button.
Select a Set-Up Function or Value Off
Not printing
Off
Press ALT-NEXT or ALTPREVIOUS button.
Press SETUP/EXIT.
a Set-Up Function or Value
Move cursor to select
a Set-Up Option
Select a Set-Up Value and
move cursor to SAVE&EXIT
Off
Not printing
Off
Clear software-detected errors
—
—
Blinking Press SETUP/EXIT
Initialize the printer
—
—
—
Turn power off and on again.
*1 In Normal mode operation, all buttons except READY are inactive in the Busy state in which the
printer is receiving or printing data.
*2 Not printing includes the following situations: the printer is ready and awaiting data, or the
READY button is pressed and the printer is awaiting data, or the READY button is pressed
during printing.
*3 This operation is available in the rear-feeding push-tractor mode.


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 5
Producer                        : GNU Ghostscript 7.06
Title                           : Microsoft Word - Ch-2-2 Paper Handling Rev C2_b.doc
Creator                         : PScript5.dll Version 5.2
Create Date                     : 4/4/2006 13:27:9
Author                          : 2328

EXIF Metadata provided by EXIF.tools