Moxa WAPN008 MOXA IEEE 802.11 a/b/g/n User Manual WAPN008 UM v2

Moxa Inc. MOXA IEEE 802.11 a/b/g/n WAPN008 UM v2

Users Manual

Moxa 802.11a/b/g/n PCI Module WAPN008 User’s Manual www.moxa.com First Edition, July 2015  2015 Moxa Inc. All rights reserved. Reproduction without permission is prohibited.
WAPN008 User’s Manual The hardware and software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright  2015 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. Trademarks MOXA is a registered trademark of Moxa Inc. All other trademarks or registered marks in this manual belong to their respective manufacturers. Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa. Moxa provides this document “as is,” without warranty of any kind, either expressed or implied, including, but not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the products and/or the programs described in this manual, at any time. Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for its use, or for any infringements on the rights of third parties that may result from its use. This product might include unintentional technical or typographical errors. Changes are periodically made to the information herein to correct such errors, and these changes are incorporated into new editions of the publication. Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: +1-714-528-6777 Fax: +1-714-528-6778 Moxa China (Shanghai office): Toll-free: 800-820-5036 Tel: +86-21-5258-9955 Fax: +86-10-6872-3958 Moxa Europe: Tel: +49-89-3 70 03 99-0 Fax: +49-89-3 70 03 99-99 Moxa Asia-Pacific: Tel: +886-2-8919-1230 Fax: +886-2-8919-1231
Table of Contents Chapter 1 Introduction Overview Specification Chapter 2 Getting Started Module Layout Block Diagram Hardware Installation Software Installation
WAPN008 User’s Manual Introduction 11 Chapter 1 Introduction The following topics are covered in this chapter:  Overview  Specifications
WAPN008 User’s Manual Introduction Overview WAPN008 PCI module is designed to provide wireless communication for Moxa industrial wireless products. It communicates via the standard 802.11a/b/g/n protocols on standard 2.4GHz/5GHz and 5GHz DFS channels. The WAPN008 uses the AR9344 SoC Wireless chipset from Atheros. Specification Features WAPN008 Chipset Atheros AR9344 Baseband Processor (BBP) - DSSS with DBPSK, DQPSK, CCK - OFDM with BPSK, QPSK, 16QAM, 64QAM - 802.11b: CCK @ 11/5.5 Mbps, DQPSK @ 2 Mbps, DBPSK @ 11 Mbps - 802.11a/g: 64QAM @ 54/48 Mbps, 16QAM @ 36/24 Mbps, QPSK @ 18/12 Mbps, BPSK @ 9/6 Mbps - 802.11n: 64QAM @ 300 Mbps to BPSK @ 6.5 Mbps (multiple rates supported) security engine - 64-bit and 128-bit WEP encryption, WPA /WPA2-Personal and Enterprise (IEEE 802.1X/RADIUS, TKIP and AES) Connectors Defined BTB connector is using 2x40 pins header, and Support PCI Express standard. Power requirement 3.3V +/-10% Dimension 60mm x 60mm x 1.2mm Operating Temperature -40 to +80 ℃ Storage Temperature: -40 to +150℃ Operates in 2.4 and 5 GHz frequency bands. US: 2.412 to 2.462 GHz (11 channels) 5.180 to 5.240 (4 channels) 5.260 to 5.320 (4 channels) 5.500 to 5.700 GHz (11 channels) 5.745 to 5.825 GHz (5 channels) EU: 2.412 to 2.472 GHz (13 channels) 5.180 to 5.240 (4 channels) 5.260 to 5.320 (4 channels) 5.500 to 5.700 GHz (11 channels) JP: 2.412 to 2.484 GHz (14 channels) 5.180 to 5.240 (4 channels) 5.260 to 5.320 (4 channels) 5.500 to 5.700 GHz (11 channels) TX Transmit Power: 802.11b: Typ. 26±1.5 dBm @ 1 Mbps, Typ. 26±1.5 dBm @ 2 Mbps, Typ. 26±1.5 dBm @ 5.5 Mbps, Typ. 25±1.5 dBm @ 11 Mbps 802.11g: Typ. 24±1.5 dBm @ 6 to 24 Mbps, Typ. 22±1.5 dBm @ 36 Mbps,
WAPN008 User’s Manual Introduction Typ. 20±1.5 dBm @ 48 Mbps, Typ. 18±1.5 dBm @ 54 Mbps 802.11n (2.4 GHz): Typ. 23±1.5 dBm @ MCS0/8 20 MHz, Typ. 17±1.5 dBm @ MCS7/15 20 MHz Typ. 23±1.5 dBm @ MCS0/8 40 MHz, Typ. 17±1.5 dBm @ MCS7/15 40 MHz 802.11a: Typ. 23±1.5 dBm @ 6 to 24 Mbps, Typ. 21±1.5 dBm @ 36 Mbps, Typ. 20±1.5 dBm @ 48 Mbps,Typ. 18±1.5 dBm @ 54 Mbps 802.11n (5 GHz): Typ. 23±1.5 dBm @ MCS0/8 20 MHz, Typ. 18±1.5 dBm @ MCS7/15 20 MHz Typ. 23±1.5 dBm @ MCS0/8 40 MHz, Typ. 18±1.5 dBm @ MCS7/15 40 MHz RX Receive Sensitivity: 802.11b: -93 dBm @ 1 Mbps, -93 dBm @ 2 Mbps, -93 dBm @ 5.5 Mbps, -88 dBm @ 11 Mbps 802.11g: -88 dBm @ 6 Mbps, -88 dBm @ 9 Mbps, -85 dBm @ 12 Mbps, -85 dBm @ 18 Mbps, -85 dBm @ 24 Mbps, -82 dBm @ 36 Mbps, -78 dBm @ 48 Mbps, -74 dBm @ 54 Mbps 802.11n (2.4 GHz): -70 dBm @ MCS7 20 MHz, -69 dBm @ MCS15 20 MHz -67 dBm @ MCS7 40MHz, -67 dBm @ MCS15 40 MHz 802.11a: -90 dBm @ 6 Mbps, -88 dBm @ 9 Mbps, -85 dBm @ 12 Mbps, -85 dBm @ 18 Mbps, -81 dBm @ 24 Mbps, -78 dBm @ 36 Mbps, -78 dBm @ 48 Mbps, -72 dBm @ 54 Mbps 802.11n (5 GHz): -69 dBm @ MCS7 20MHz, -71 dBm @ MCS15 20 MHz -66 dBm @ MCS7 40MHz, -68 dBm @ MCS15 40 MHz
22 Chapter 2 Getting Started This chapter covers the module layout, and block diagram, hardware installation of the WAPN008. Software installation is covered in the next chapter. The following topics are covered:  Module Layout  Block Diagram  Hardware Installation  Software Installation
WAPN008 User’s Manual Getting Started Module Layout Top and Bottom Block Diagram Below is a block diagram of the WAPN008.
WAPN008 User’s Manual Getting Started Connector Locations
WAPN008 User’s Manual Getting Started PCI Bus Connector PIN Assignments Function Connect to Pin Pin Function Connect to 3.3v 3.3v 1 2 GND GND 3.3v 3.3v 3 4 GND GND 3.3v 3.3v 5 6 ERXD3 PHY RGMII 3.3v 3.3v 7 8 ERXD2 PHY RGMII 3.3v 3.3v 9 10 ERXD1 PHY RGMII 3.3v 3.3v 11 12 ERXD0 PHY RGMII 3.3v 3.3v 13 14 GND GND GPIO 16 I2C_SCLK 15 16 GND GND GPIO 17 I2C_DATA 17 18 ETX_CLK ETX_CLK GND GND 19 20 GND GND GPIO 21 POWER 2 21 22 GND GND GPIO 1 JP1 Debug 23 24 ETX_EN ETX_EN GND GND 25 26 GND GND GPIO 4 S17_INT 27 28 GND GND GND GND 29 30 ETXD3 PHY RGMII GPIO 0 I2C_INT0 31 32 ETXD2 PHY RGMII GND GND 33 34 ETXD1 PHY RGMII GPIO 3 UR_DSR 35 36 ETXD0 PHY RGMII GPIO 9 UR_SIN 37 38 GND GND GPIO 10 UR_SOUT 39 40 GND GND GPIO 13 MDC 41 42 ERX_CLK ERX_CLK GPIO 14 MDIO 43 44 GND GND GPIO 20 POWER 1 45 46 GND GND GND GND 47 48 ERX_EN ERX_EN GPIO 22 POWER 3 49 50 GND GND GND GND 51 52 GND GND GPIO 2 UR_DTR 53 54 EMDC GIGA PHY GND GND 55 56 EMDIO GIGA PHY GPIO 11 Reset 57 58 GND GND GND GND 59 60 GND GND GPIO 12 LAN 10/100 61 62 TXP0 10/100 LAN GND GND 63 64 TXN0 10/100 LAN GPIO 15 Reserved 65 66 GND GND GND GND 67 68 RXP0 10/100 LAN SYS_RST_L GIGA PHY Reset 69 70 RXN0 10/100 LAN AVDD18 Fast Ethernet bios 71 72 GND GND AVDD18 Fast Ethernet bios 73 74 GND GND AVDD18 Fast Ethernet bios 75 76 USB_DM USB port GND GND 77 78 USB_DP USB port GND GND 79 80 GND GND
WAPN008 User’s Manual Getting Started Hardware Installation The WAPN008 can be installed into all Moxa wireless system board series. Step for Installation 1. Install the WAPN008 PCI card on the system board. Apply pressure to both bus connectors and gently press the board onto the stack. The board should slide into the matching bus connectors. Do not attempt to force the board, as this can lead to bent/broken pins. 2. Screw on the WAPN008 PCI card. 3. Screw on the all the necessary chassis. Software Installation After physically installing the WAPN008, your operating system must be configured to recognize the new system board. Step for Installation 1. Apply power to the system board. 2. Connect system board and PC with Ethernet cable. 3. Open a browser and type: 192.168.127.253 to open the system login webpage. 4. Login the webpage with default password: root in order to verify that all of the hardware is install properly.
WAPN008 User’s Manual Getting Started Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: This module is restricted to mobile configuration. To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID: SLE-WAPN008 ”
WAPN008 User’s Manual Getting Started Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. This radio transmitter FCCID: SLE-WAPN008 has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna List No. Manufacturer Part No. Antenna Type Peak Gain 1 KINSUN ANT-WDB-O-2 BK Dipole 2.9dBi for 2.4 GHz 2.34dBi for 5GHz 2 KINSUN ANT-WDB-ANM-0502 Dipole 4.62dBi for 2.4 GHz 1.41dBi for 5GHz Note: The antenna connector is Reverse SMA type

Navigation menu