Moxa WAPN008 MOXA IEEE 802.11 a/b/g/n User Manual Moxa Tough AP TAP 213 User s Manual

Moxa Inc. MOXA IEEE 802.11 a/b/g/n Moxa Tough AP TAP 213 User s Manual

WAPN008- UserMan_AWK-3131A-SSC-RTG_20180820

Moxa AWK-3131A-RTG User’s Manual Edition 1.0, July 2018 www.moxa.com/product © 2018 Moxa Inc. All rights reserved.
Moxa AWK-3131A-RTG User’s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice © 2018 Moxa Inc. All rights reserved. Trademarks The MOXA logo is a registered trademark of Moxa Inc. All other trademarks or registered marks in this manual belong to their respective manufacturers. Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa. Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the products and/or the programs described in this manual, at any time. Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for its use, or for any infringements on the rights of third parties that may result from its use. This product might include unintentional technical or typographical errors. Changes are periodically made to the information herein to correct such errors, and these changes are incorporated into new editions of the publication. Technical Support Contact Information www.moxa.com/support Moxa Americas Toll-free: 1-888-669-2872 Tel: +1-714-528-6777 Fax: +1-714-528-6778 Moxa China (Shanghai office) Toll-free: 800-820-5036 Tel: +86-21-5258-9955 Fax: +86-21-5258-5505 Moxa Europe Tel: +49-89-3 70 03 99-0 Fax: +49-89-3 70 03 99-99 Moxa Asia-Pacific Tel: +886-2-8919-1230 Fax: +886-2-8919-1231 Moxa India Tel: +91-80-4172-9088 Fax: +91-80-4132-1045
Table of Contents 1. Introduction ...................................................................................................................................... 1-1 Overview ........................................................................................................................................... 1-2 Package Checklist ............................................................................................................................... 1-2 Product Features ................................................................................................................................ 1-2 Product Specifications ......................................................................................................................... 1-3 Functional Design ............................................................................................................................... 1-3 LAN Port .................................................................................................................................... 1-3 LED Indicators ............................................................................................................................ 1-4 Beeper ....................................................................................................................................... 1-5 Reset Button ............................................................................................................................... 1-5 2. Getting Started .................................................................................................................................. 2-1 First-Time Installation and Configuration ............................................................................................... 2-2 Communication Testing ....................................................................................................................... 2-3 Function Map ..................................................................................................................................... 2-5 3. Web Console Configuration ............................................................................................................... 3-1 Web Browser Configuration .................................................................................................................. 3-3 Overview ........................................................................................................................................... 3-4 Basic Settings .................................................................................................................................... 3-5 System Info Settings ................................................................................................................... 3-6 Network Settings ......................................................................................................................... 3-6 Time Settings ............................................................................................................................. 3-8 Wireless Settings .............................................................................................................................. 3-10 Operation Mode ................................................................................................................................ 3-10 Basic Wireless Settings (Multiple SSID) ............................................................................................... 3-11 WLAN Security Settings .............................................................................................................. 3-14 Advanced Wireless Settings ........................................................................................................ 3-21 WLAN Certification Settings (Only For EAP-TLS in Client Mode) ....................................................... 3-26 WAC Settings (AP Mode Only) ..................................................................................................... 3-27 Advanced Settings ............................................................................................................................ 3-27 Using Virtual LAN ...................................................................................................................... 3-28 Configuring Virtual LAN .............................................................................................................. 3-29 DHCP Server ............................................................................................................................. 3-30 Packet Filters ............................................................................................................................ 3-31 Static Route (For Client-Router Mode Only) .................................................................................. 3-33 NAT Settings/Port Forwarding (For Client-Router Mode Only) .......................................................... 3-35 SNMP Agent .............................................................................................................................. 3-36 Mobile IP Settings ...................................................................................................................... 3-38 Link Fault Pass-Through (For Client Mode Only) ............................................................................ 3-39 Auto Warning Settings....................................................................................................................... 3-40 System Log .............................................................................................................................. 3-40 Syslog ..................................................................................................................................... 3-41 E-mail ...................................................................................................................................... 3-42 Traps ....................................................................................................................................... 3-43 Status ............................................................................................................................................. 3-45 Wireless Status ......................................................................................................................... 3-45 Associated Client List (For AP Mode Only) ..................................................................................... 3-45 DHCP Client List ........................................................................................................................ 3-46 System Log .............................................................................................................................. 3-46 Relay Status ............................................................................................................................. 3-47 DI and Power Status .................................................................................................................. 3-47 AeroLink Protection Status (For Client Mode Only) ......................................................................... 3-47 Routing Table ........................................................................................................................... 3-48 LAN Status ............................................................................................................................... 3-48 Maintenance .................................................................................................................................... 3-48 Console Settings ....................................................................................................................... 3-48 Ping ......................................................................................................................................... 3-49 Firmware Upgrade ..................................................................................................................... 3-49 Config Import/Export ................................................................................................................. 3-50 Load Factory Default .................................................................................................................. 3-51 Username/Password .................................................................................................................. 3-51 Locate Device ........................................................................................................................... 3-51 Misc. Settings ........................................................................................................................... 3-52 Save Configuration ........................................................................................................................... 3-52 Restart ............................................................................................................................................ 3-53 Logout............................................................................................................................................. 3-53 4. Software Installation and Configuration ........................................................................................... 4-1 Overview ........................................................................................................................................... 4-2
Wireless Search Utility ......................................................................................................................... 4-2 Installing Wireless Search Utility ................................................................................................... 4-2 Configuring Wireless Search Utility ................................................................................................ 4-5 5. Using Other Consoles ........................................................................................................................ 5-1 USB Console Configuration (115200, None, 8, 1, VT100) ......................................................................... 5-2 Configuration via Telnet and SSH Consoles ............................................................................................ 5-4 Configuration by Web Browser with HTTPS/SSL ...................................................................................... 5-5 Disabling Telnet and Browser Access ..................................................................................................... 5-6 A. References ........................................................................................................................................ A-1 Beacon ..............................................................................................................................................A-2 DTIM.................................................................................................................................................A-2 Fragment...........................................................................................................................................A-2 RTS Threshold ....................................................................................................................................A-2 STP and RSTP ....................................................................................................................................A-2 The STP/RSTP Concept ................................................................................................................A-2 Differences between RSTP and STP................................................................................................A-3 B. Supporting Information .................................................................................................................... B-1 Firmware Recovery .............................................................................................................................B-2 DoC (Declaration of Conformity) ...........................................................................................................B-3 Federal Communication Commission Interference Statement ............................................................B-3 RED Compliance Statement ..........................................................................................................B-3 Canada, Industry Canada (IC) Notices ...........................................................................................B-4 Antenna Gain and RF Radiated Power ............................................................................................B-5 R&TTE Compliance Statement .......................................................................................................B-7
1 Introduction The AWK-3131A-RTG series wireless AP/client is the wireless solution for railway train-to-ground applications such as CCTV and CBTC communications. It can provide speeds of up to 300 Mbps with IEEE 802.11n technology. The AWK-3131A-RTG series can operate at temperatures ranging from -25 to 60°C for standard models and -40 to 75°C for extended temperature models, and is rugged enough for rolling stock environments. Installation is easy, with either DIN-rail mounting or distribution boxes, and the DIN-rail mounting capability, wide operating temperature range, and IP30 housing with LED indicators make the AWK-3131A-RTG a convenient yet reliable solution for any rolling stock application. The following topics are covered in this chapter:  Overview  Package Checklist  Product Features  Product Specifications  Functional Design  LAN Port  LED Indicators  Beeper  Reset Button
AWK-3131A-RTG UM Introduction 1-2 Overview The AWK-3131A-RTG is 802.11n compliant to deliver speed, range, and reliability to support even the most bandwidth-intensive applications. The 802.11n standard incorporates multiple technologies, including MIMO (Multi-In, Multi-Out) Spatial Multiplexing, multiple channels (5, 10, 20 and 40 MHz), and dual bands (2.4 GHz and 5 GHz) to achieve high speeds, while still being able to communicate with legacy 802.11a/b/g devices. The AWK-3131A-RTG is compliant with the EN 50155 standard that covers operating temperature range, power input voltage, surge, ESD, and vibration. The AWK-3131A-RTG can be easily mounted on to a wall, DIN rail or in distribution boxes. Its wide operating temperature range, IP68-rated housing with LED indicators, and the DIN-rail mounting capability make the AWK-3131A-RTG a convenient yet reliable solution for all types of industrial wireless applications. Package Checklist Moxa’s AWK-3131A-RTG is shipped with the following items. If any of these items is missing or damaged, please contact your customer service representative for assistance. • 1 AWK-3131A-RTG • 1 DIN-rail kit • 2 plastic RJ45 protective cap: One for the console port and the other for use as a backup • 1 plastic protective cap for fiber port (AWK-3131A-SSC-RTG only) • Cable holder with one screw • Quick installation guide (printed) • Warranty card NOTE Antennas are not included and should be purchased separately. Product Features • Designed specifically for the wireless communication requirements in train-to-ground communication (e.g.: CBTC and CCTV). • 2x2 MIMO technology • M12 anti-vibration connectors (AWK-3131A-M12-RTG) • SC optical fiber connection (AWK-3131A-SSC-RTG) • -40 to 75°C operating temperature range (T models) • Certified against the EN 50121-4 railway standard • Complies with all EN 50155 mandatory test items* • Controller-based Turbo Roaming (handover time < 50 ms @ 3 channels, WPA2) - available only when used with the WAC-1001 or WAC-2004 • Supports 5.8 GHz band in the standard model • Supports QoS function, which can help assign high priority to your critical traffic • Provides advanced wireless security settings • Provides 64-bit and 128-bit WEP/WPA/WPA2 encryption • SSID Hiding, IEEE 802.1X security, and RADIUS • Packet access control and filtering • Supports SNMP, SNTP, SSH, HTTPS, TFTP for remote management • Wall mountable • Long-distance transmission support
AWK-3131A-RTG UM Introduction 1-3 ATTENTION • The AWK-3131A-RTG is NOT a portable mobile device and should be located at least 20 cm away from the human body. • The AWK-3131A-RTG is NOT designed for the general public. To establish a wireless network safely using the AWK-3131A-RTG, a well-trained technician should be consulted for installation. There are many factors that affect the performance of a device when it is used in long-distance applications. These factors include: • Test architecture • Installation distance • Car speed • Antenna gain • Band • Transmission Power • Signal Strength • Channel interference For details, please contact your Moxa sales representative. Product Specifications NOTE The latest specifications for Moxa’s products can be found at https://www.moxa.com. Functional Design LAN Port The standard model of the AWK-3131A-RTG is provided with one M12 D code Megabit port. The LAN LED will light up when you insert the cable in the LAN port and a connection is established. The standard model of AWK-3131A-SSC-RTG is provided with one SC fiber port. The 100M LED will light up when you insert the cable in the SC fiber port and a connection is established.
AWK-3131A-RTG UM Introduction 1-4 LED Indicators The LEDs on the front panel provide a quick and easy means of determining the current operational status and wireless settings of the AWK-3131A-RTG. The FAULT LED indicates system failures. If the AWK-3131A-RTG cannot retrieve the IP address from a DHCP server, the FAULT LED will blink at one-second intervals. The following table summarizes how to read the device’s wireless settings based on the LED displays. More information is available in Chapter 3 in the “Basic Wireless Settings” section. LED Color State Description PWR1 Green On Power is being supplied from power input 1. Off Power is not being supplied from power input 1. PWR2 Green On Power is being supplied from power input 2. Off Power is not being supplied from power input 2. PoE (AWK-3131A- M12-RTG only) Amber On Power is being supplied via PoE. Off Power is not being supplied via PoE. FAULT Red Blinking (slow at 1-second intervals) Cannot get an IP address from the DHCP server Blinking (fast at 0.5-second intervals) IP address conflict Off No errors STATE Green/ Red Green System startup is complete and the system is in operation Green (blinking at 1-second intervals) The AWK has been located by the Wireless Search Utility. Red Boot up error SIGNAL (5 LEDs) Green On Signal level (for Client and Client-Router mode only) Off CLIENT MODE Green On The AWK is functioning in Client or Client-Router Mode. Off The AWK is not functioning in Client or Client-Router Mode. ATTENTION Do not use a PoE (Power over Ethernet) Injector for the PoE device(s). Instead, use an IEEE 802.3af or IEEE 802.3at compliant PSE (Power Sourcing Equipment).
AWK-3131A-RTG UM Introduction 1-5 ATTENTION When the system fails to boot, the LEDs for STATE (Green), FAULT, and WLAN will all light up simultaneously and blink at one-second intervals. This may be due to improper operation or issues such as an unexpected shutdown while updating the firmware. To recover the firmware, refer to the “Firmware Recovery” section in Appendix B Supporting Information. LED Color State Description WLAN Amber On WLAN is in use. Off WLAN is not in use. LAN/ 100M* Green On 100 Mbps link is active. Blinking Data is being transmitted at 100 Mbps. Off 100 Mbps link is inactive. Beeper The beeper emits two short beeps when the system is ready. Reset Button The Reset button is located on the bottom panel of the AWK-3131A-RTG. You can reboot the AWK-3131A-RTG or reset it to factory default settings by pressing the Reset button with a pointed object such as an unfolded paper clip. • System reboot: Hold the Reset button down for under 5 seconds and then release. • Reset to factory default: Hold the Reset button down for over 5 seconds until the STATE LED starts blinking green light. Release the button to reset the AWK-3131A-RTG.
2 Getting Started This chapter explains how to install Moxa’s AirWorks AWK-3131A-RTG for the first time to quickly set up your wireless network and how to test whether the connection is working well. The function map provided in Chapter 3 is a convenient reference to the various functions available on the AWK-3131A-RTG and to determine the functions that you need to use. The following topics are covered in this chapter:  First-Time Installation and Configuration  Communication Testing  Function Map
AWK-3131A-RTG UM Getting Started 2-2 First-Time Installation and Configuration Before installing the AWK-3131A-RTG, make sure that all items mentioned in the package checklist are in the box. You will also need access to a notebook computer or PC equipped with an Ethernet port. The AWK-3131A-RTG has a default IP address that you must use when connecting to the device for the first time. • Step 1: Select the power source. The AWK-3131A-RTG can be powered by a DC power input or PoE (Power over Ethernet). • Step 2: Connect the AWK-3131A-RTG to a notebook or PC. Since the AWK-3131A-RTG is provided with the MDI/MDI-X auto-sensing capability, you can use either a straight-through cable or crossover cable to connect it to a computer. When the connection between the AWK-3131A-RTG and the computer is established, the LED indicator on the AWK-3131A-RTG’s LAN port lights up. • Step 3: Set up the computer’s IP address. Set an IP address for the computer so that it is on the same subnet as that of the AWK-3131A-RTG. Since the AWK-3131A-RTG’s default IP address is 192.168.127.253, and the subnet mask is 255.255.255.0, set the IP address of the computer in the 192.168.127.xxx IP range and subnet mask to 255.255.255.0. • Step 4: Use the web-based manager to configure the AWK-3131A-RTG Open your computer’s web browser and type http://192.168.127.253 in the address field to access the homepage of the web-based Network Manager. Before the homepage opens, you will need to enter the user name and password as shown in the following figure. For first-time configuration, enter the following default user name and password and click on the Login button: User Name: admin Password: moxa NOTE For security reasons, we strongly recommend changing the default password. To change the password, select Maintenance  Password and follow the instructions on the screen. NOTE After you click Submit to apply changes, the web page is refreshed and an (Updated) indicator is displayed next to the page heading along with a blinking reminder to restart the device. To activate the changes, click Restart and then click Save and Restart after you change the settings. The AWK-3131A-RTG will take about 30 seconds to complete the reboot process.
AWK-3131A-RTG UM Getting Started 3-2 • Step 5: Select the operation mode for the AWK-3131A-RTG. By default, the operation mode of the AWK-3131A-RTG is set to AP. You can change this setting to Client mode at Wireless Settings  WLAN  Basic Wireless Settings. Detailed information about configuring the AWK-3131A-RTG is available in Chapter 3. • Step 6: Test the network connection. In the following sections we describe two methods that you can use to test that a network connection has been established. Communication Testing After installing the AWK-3131A-RTG you can run a sample test to make sure the wireless connection on the AWK-3131A-RTG is functioning normally. Two testing methods are described below. Use the first method if you are using only one AWK-3131A-RTG device and the second method if you are using two or more AWK-3131A-RTG units. How to Test One AWK-3131A-RTG If you are only using one AWK-3131A-RTG, you will need one additional notebook computer equipped with a WLAN card. Configure the WLAN card to connect to the AWK-3131A-RTG (NOTE: the default SSID is MOXA), and change the IP address of the second notebook (Notebook B) so that it is on the same subnet as the first notebook (Notebook A), which is connected to the AWK-3131A-RTG. After configuring the WLAN card, establish a wireless connection with the AWK-3131A-RTG and open a DOS window on Notebook B. At the prompt, type the following: ping <IP address of notebook A> and then press Enter (see the figure below). A “Reply from IP address …” response means the communication was successful. A “Request timed out.” response means the communication failed. In this case, recheck the configuration to make sure the connections are correct.
AWK-3131A-RTG UM Getting Started 4-2 How to Test Two or More AWK-3131A-RTG Units If you have two or more AWK-3131A-RTG units, you will need a second notebook computer (Notebook B) equipped with an Ethernet port. Use the default settings for the first AWK-3131A-RTG connected to notebook A and change the second or third AWK-3131A-RTG connected to notebook B to Client mode, and then configure the notebooks and AWK-3131A-RTG units properly. After setting up the testing environment, open a DOS window on notebook B. At the prompt type: ping <IP address of notebook A> and then press Enter. A “Reply from IP address …” response means the communication was successful. A “Request timed out” response means the communication failed. In the latter case, recheck the configuration to make sure the settings are correct.
AWK-3131A-RTG UM Getting Started 5-2 Function Map Quick overview of the AWK-3131A-M12-RTG’s status Essential settings related to establishing a wireless network Advanced features to support additional network management and secure wired and wireless communication Note: These advanced functions are all optional Application-oriented device management functions to set up events, traps, and reactions via e-mail and SNMP notifications Note: These functions are all optional On-demand functions to support the web-based console management operation Functions for maintaining the AWK-3131A-M12-RTG, and for diagnosing the network Basic settings for administering the AWK-3131A-M12-RTG Current status information for monitoring wired/wireless network performance, advanced services, and device management functions
3 Web Console Configuration In this chapter, we explain all aspects of web-based console configuration. Moxa’s easy-to-use management functions help you set up your AWK-3131A-RTG and make it easy to establish and maintain your wireless network. The following topics are covered in this chapter:  Web Browser Configuration  Overview  Basic Settings  System Info Settings  Network Settings  Time Settings  Wireless Settings  Operation Mode  Basic Wireless Settings (Multiple SSID)  WLAN Security Settings  Advanced Wireless Settings  WLAN Certification Settings (Only For EAP-TLS in Client Mode)  WAC Settings (AP Mode Only)  Advanced Settings  Using Virtual LAN  Configuring Virtual LAN  DHCP Server  Packet Filters  NAT Settings/Port Forwarding (For Client-Router Mode Only)  SNMP Agent  Mobile IP Settings  Link Fault Pass-Through (For Client Mode Only)  Auto Warning Settings  System Log  Syslog  E-mail  Traps  Status  Wireless Status  Associated Client List (For AP Mode Only)  DHCP Client List  System Log  Relay Status  DI and Power Status
AWK-3131A-RTG UM Web Console Configuration 3-2  AeroLink Protection Status (For Client Mode Only)  Routing Table  LAN Status  Maintenance  Console Settings  Ping  Firmware Upgrade  Config Import/Export  Load Factory Default  Username/Password  Locate Device  Misc. Settings  Save Configuration
AWK-3131A-RTG UM Web Console Configuration 3-3 NOTE To use the management and monitoring functions of the AWK-3131A-RTG from a PC host connected to the same LAN as the AWK-3131A-RTG, you must make sure that the PC host and the AWK-3131A-RTG are on the same logical subnet. Similarly, if the AWK-3131A-RTG is configured on a different VLAN than the PC, you must make sure your PC host is on the management VLAN so that it can access the AWK-3131A-RTG. The default IP address of the AWK is 192.168.127.253.  Restart  Logout Web Browser Configuration The web interface provides a convenient way to modify the configuration of the AWK-3131A-RTG and access its built-in monitoring and network administration functions. The recommended web browser is Microsoft® Internet Explorer 11.0 with JVM (Java Virtual Machine) installed. To access the web interface of the AWK-3131A-RTG, do the following: 1. Open a web browser (e.g., Internet Explorer), type in the default IP address of the AWK-3131A-RTG in the address field, and press Enter. 2. In the login page that is displayed, enter the Username and Password (default Username = admin; default Password = moxa) and click Login to continue.
AWK-3131A-RTG UM Web Console Configuration 3-4 NOTE The model name of the AWK-3131A-RTG is shown as AWK-3131A-RTG-XX, where XX indicates the country code. The model name indicates the AWK-3131A-RTG version and the bandwidth it uses. We use AWK-3131A-RTG-US as an example in the following figures. (The country code and model name that appears on your computer screen may be different.) You may need to wait a few moments for the main page to download to your computer. Note that the model name and IP address of the AWK-3131A-RTG are both shown in the title bar of the web page. You can identify the web interfaces of multiple AWK-3131A-RTG units using this information. 3. Use the menu tree on the left side of the window to open the configuration pages for the AWK-3131A-RTG’s functions. In the following paragraphs, we describe each AWK-3131A-RTG management function in detail. An overview of all the functions is available in the “Function Map” section of this manual. Overview The Overview page summarizes the AWK-3131A-RTG’s current status. The information is categorized into the following groups: System Info, Device Info, and 802.11 Info.
AWK-3131A-RTG UM Web Console Configuration 3-5 Click on the SSID (MOXA, in this case) to display detailed information on 802.11as shown below: NOTE The 802.11 Info that is displayed may differ based on the operation mode selected. For example, Current BSSID is not available in Client mode, and Signal strength/Noise Floor is not available in AP mode. Basic Settings The Basic Settings group includes the most commonly used settings required by administrators to maintain and control the AWK-3131A-RTG.
AWK-3131A-RTG UM Web Console Configuration 3-6 System Info Settings The System Info related settings that you configure here, especially the Device name and Device description, are displayed on the Overview page. They are also included in the SNMP information and email alerts. Configuring the System Info settings for each AWK-3131A-RTG makes it easier to identify the different AWK-3131A-RTG units connected to your network. Device name Format Description Factory Default Maximum of 31 characters Specifies the role or application of this AWK-3131A-RTG unit. AWK-3131A-RTG_<Serial No. of this AWK-3131A-RTG> Device location Format Description Factory Default Maximum. of 31 characters Specifies the location of this AWK-3131A-RTG unit. None Device description Format Description Factory Default Maximum of 31 characters You can use this space to record a more detailed description of this AWK-3131A-RTG None Device contact information Format Description Factory Default Maximum of 31 characters You can use this space to record the contact information of the person responsible for maintaining this AWK-3131A-RTG. None Network Settings The Network Settings configuration panel allows you to modify the usual TCP/IP network parameters. However, due to the addition of the client-router operation mode, this panel provides two different sets of network parameters. Explanations for both types of configuration are given below. Network Settings for AP/Client Operation Mode
AWK-3131A-RTG UM Web Console Configuration 3-7 IP address assignment Setting Description Factory Default DHCP The AWK-3131A-RTG’s IP address will be assigned automatically by the network’s DHCP server Static Static Set up the AWK-3131A-RTG’s IP address manually. IP address Setting Description Factory Default AWK-3131A-RTG’s IP address Identifies the AWK-3131A-RTG on a TCP/IP network. 192.168.127.253 Subnet mask Setting Description Factory Default AWK-3131A-RTG’s subnet mask Identifies the type of network to which the AWK-3131A-RTG is connected (e.g., 255.255.0.0 for a Class B network, or 255.255.255.0 for a Class C network). 255.255.255.0 Gateway Setting Description Factory Default AWK-3131A-RTG’s default gateway The IP address of the router that connects the LAN to an outside network. None Primary/ Secondary DNS server Setting Description Factory Default IP address of the Primary/Secondary DNS server The IP address of the DNS Server used by your network. After entering the DNS Server’s IP address, you can input the AWK-3131A-RTG’s URL (e.g., http://ap11.abc.com) in your browser’s address field instead of entering the IP address. The Secondary DNS server will be used if the Primary DNS server fails to connect. None Network Settings for Client-Router Operation Mode WLAN IP address assignment Setting Description Factory Default DHCP The AWK-3131A-RTG WLAN interface’s IP address will be assigned automatically by the network’s DHCP server Static
AWK-3131A-RTG UM Web Console Configuration 3-8 Static Set up the AWK-3131A-RTG WLAN interface’s IP address manually. WLAN IP address Setting Description Factory Default AWK-3131A-RTG WLAN interface’s IP address Identifies the AWK-3131A-RTG WLAN interface’s IP address on a TCP/IP network. 192.168.128.253 WLAN subnet mask Setting Description Factory Default AWK-3131A-RTG WLAN interface’s subnet mask Identifies the type of network to which the AWK-3131A-RTG’s WLAN interface is connected (e.g., 255.255.0.0 for a Class B network, or 255.255.255.0 for a Class C network). 255.255.255.0 WLAN gateway Setting Description Factory Default AWK-3131A-RTG WLAN interface’s default gateway The IP address of the router that connects the WLAN to an outside network. None Primary/Secondary DNS server Setting Description Factory Default IP address of the Primary/Secondary DNS server The IP address of the DNS Server used by your network. After entering the DNS Server’s IP address, you can input the AWK-3131A-RTG’s URL (e.g., http://ap11.abc.com) in your browser’s address field instead of entering the IP address. The Secondary DNS server will be used if the Primary DNS server fails to connect. None LAN IP address Setting Description Factory Default AWK-3131A-RTG LAN interface’s IP address Identifies the AWK-3131A-RTG LAN interface’s IP address on a TCP/IP network. 192.168.127.253 LAN subnet mask Setting Description Factory Default AWK-3131A-RTG LAN interface’s subnet mask Identifies the type of network to which the AWK-3131A-RTG’s LAN interface is connected (e.g., 255.255.0.0 for a Class B network, or 255.255.255.0 for a Class C network). 255.255.255.0 Time Settings The AWK-3131A-RTG has a time calibration function that can update the date and time information based on an NTP server or the date and time information specified by the user.
AWK-3131A-RTG UM Web Console Configuration 3-9 ATTENTION Changing the time zone will automatically adjust the Current local time. You should configure the Time zone before setting the Current local time. The Current local time shows the AWK-3131A-RTG’s system time when you open this web page. After you update the date and time setting, click on the Set Time button to activate the new date and time. An “(Updated)” string is displayed next to the date and time fields to indicate that the change is complete. Any change in the date and time setting is effective immediately and does not need a system restart. NOTE The AWK-3131A-RTG has a built-in real time clock (RTC). The RTC is a computer clock (most often in the form of an integrated circuit) that keeps track of the current time. We strongly recommend that users update the Time Settings of the AWK-3131A-RTG after the initial setup is complete or when the AWK-3131A-RTG is switched on after a long-term shutdown, especially if the network does not have an Internet connection for accessing a NTP server or there is no NTP server on the LAN. Current local time Setting Description Factory Default User-specified date and time The date and time parameters allow configuration of the local time with immediate activation. Use 24-hour format: yyyy/mm/dd hh:mm:ss None Time zone Setting Description Factory Default User-specified time zone The time zone setting allows the conversion from GMT (Greenwich Mean Time) to the local time. GMT Daylight saving time Setting Description Factory Default Enable/ Disable Daylight saving time (also known as DST or summer time) involves advancing clocks (usually 1 hour) during the summer time to provide an extra hour of daylight in the afternoon. Disable When Daylight saving time is enabled, the following parameters will be shown: • Starts at: The date that daylight saving time begins. • Stops at: The date that daylight saving time ends. • Time offset: Indicates the number of hours the clock should be advanced. Time server 1/2 Setting Description Factory Default IP address of the name of the Time Server 1/2 IP address or domain name of the NTP time server. The second NTP server will be used if the first NTP server fails to time.nist.gov
AWK-3131A-RTG UM Web Console Configuration 3-10 connect. Query period Setting Description Factory Default The query period to sync with the time server (1 to 9999 seconds) This parameter determines how often the time is updated from the NTP server. 600 (seconds) Wireless Settings The essential settings for wireless networks are presented in the wireless settings function group. You must configure these settings correctly before you establish your wireless network. Familiarize yourself with the following terms before starting the configuration process: AP: In a wireless local area network (WLAN), an access point is a station that transmits and receives data. Client: When the AWK-3131A-RTG is configured for Client mode, it can be used as an Ethernet-to-wireless (or LAN-to-WLAN) network adapter. For example, a notebook computer equipped with an Ethernet adaptor but no wireless card can be connected to this device with an Ethernet cable to provide wireless connectivity to another AP. Operation Mode The AWK-3131A-RTG supports five main operation modes—AP, Client, and Client-Router, each of which plays a distinct role on the wireless network. Wireless Enable Setting Description Factory Default Enable/Disable Use this function to turn the RF (Radio Frequency) module on or off manually. NOTE: This function is available in AP operation mode only. Enable Operation Mode Setting Description Factory Default AP The most common mode used by the AWK-3131A-RTG wherein AP
AWK-3131A-RTG UM Web Console Configuration 3-11 it plays the role of a wireless AP Client In this mode, the AWK-3131A-RTG can connect to wireless AP devices Client-Router The AWK-3131A-RTG plays the role of a wireless client and a router. Sniffer Turns the device into a remote Wireshark interface to capture 802.11 packets for analysis. Sniffer Mode Instructions: 1. Set operation mode to Sniffer mode on the AWK-3131A-RTG and then save/reboot the device. 2. Connect the AWK-3131A-RTG to a laptop with Wireshark installed (v1.12.0 or later release) via Ethernet. 3. Add a remote interface by entering the IP address of the AWK-3131A-RTG. Detailed Wireshark instructions can be found at: https://www.wireshark.org/docs/wsug_html_chunked/ChCapInterfaceRemoteSection.html 4. Start capturing 802.11 wireless packets with Wireshark. Basic Wireless Settings (Multiple SSID) You can add new SSIDs or edit existing ones in the WLAN Basic Setting Selection panel. You can configure up to 9 SSIDs for an AWK and configure each SSID differently. An SSID is a unique identifier that wireless networking devices use to establish and maintain wireless connectivity. Multiple access points on a network or sub-network can use the same SSIDs. All of the SSIDs that you configure for an AP are active at the same time. That is, client devices can use any of the SSIDs to associate with the AP. To create an SSID for your AWK, click on Add SSID. To edit an existing SSID and assign different configuration settings to it, click on the Edit button corresponding to the SSID. A configuration panel is displayed as follows:
AWK-3131A-RTG UM Web Console Configuration 3-12 NOTE When you switch to Client mode, a Site Survey button will be available on the Basic Wireless Settings panel. Use the Site Survey function to view information about available APs, as shown in the following figures. You can also click on an SSID listed on the Site Survey page to bring the details of the SSID onto the Basic Wireless Settings page. To update the site survey table, click the Refresh button. If this client is connecting to an AP, a brief disconnection will occur when you click on Site Survey. RF type Setting Description Factory Default 2.4 GHz B Only supports the IEEE 802.11b standard B/G/N Mixed G Only supports the IEEE 802.11g standard
AWK-3131A-RTG UM Web Console Configuration 3-13 B/G Mixed Supports IEEE 802.11b/g standards, but 802.11g might operate at a slower speed when 802.11b clients are on the network G/N Mixed Supports IEEE 802.11g/n standards, but 802.11n might operate at a slower speed if 802.11g clients are on the network B/G/N Mixed Supports IEEE 802.11b/g/n standards, but 802.11g/n might operate at a slower speed if 802.11b clients are on the network N Only (2.4GHz) Only supports the 2.4 GHz IEEE 802.11n standard 5 GHz A Only supports the IEEE 802.11a standard A/N Mixed Supports IEEE 802.11a/n standards, but 802.11n may operate at a slower speed if 802.11a clients are on the network N Only (5GHz) Only supports the 5 GHz IEEE 802.11n standard Channel (for AP mode only) Setting Description Factory Default The available channels vary with the RF type setting The channel on which the AWK should operate. The AWK-3131A-RTG plays the role of a wireless AP here. 6 (in B/G/N Mixed mode) Channel Width (for any 11N RF type only) Setting Description Factory Default 20 MHz Select the channel width. If you are not sure, use the 20/40 MHz (Auto) option 20 MHz 20/40 MHz Channel bonding If you have selected 20/40 MHz only in the Channel Width setting, this setting will automatically set the channel based on the Channel setting. SSID Setting Description Factory Default Maximum of 31 characters The SSID of a client and the SSID of the AP must be identical for the client and AP to be able to communicate with each other. MOXA SSID broadcast (for AP mode only) Setting Description Factory Default Enable/Disable Use this setting to specify if the SSID can be broadcast or not Enable Management frame encryption Setting Description Factory Default Enable/Disable Enables management frame encryption to protect your wireless network from DoS attacks. This function only works with Moxa's TAP and AWK-RTG series. Disable 50ms Turbo Roaming (controller-based) Setting Description Factory Default Enable/Disable Determines whether or not the AWK-3131A-RTG supports 50 ms roaming. This function only works with the WAC-1001, WAC-2004, TAP, and AWK-RTG series. Disable
AWK-3131A-RTG UM Web Console Configuration 3-14 WLAN Security Settings The AWK-3131A-RTG provides four standardized wireless security modes: Open, WEP (Wired Equivalent Privacy), WPA (Wi-Fi Protected Access), and WPA2. Several security modes are available in the AWK-3131A-RTG by selecting Security mode and WPA type: • Open: No authentication, no data encryption. • WEP: Static WEP (Wired Equivalent Privacy) keys must be configured manually. • WPA/WPA2-Personal: Also known as WPA/WPA2-PSK. You will need to specify the Pre-Shared Key in the Passphrase field, which will be used by the TKIP or AES engine as a master key to generate keys that actually encrypt outgoing packets and decrypt incoming packets. • WPA/WPA2-Enterprise: Also called WPA/WPA2-EAP (Extensible Authentication Protocol). In addition to device-based authentication, WPA/WPA2-Enterprise enables user-based authentication via IEEE 802.1X. The AWK-3131A-RTG can support three EAP methods: EAP-TLS, EAP-TTLS, and EAP-PEAP. Security mode Setting Description Factory Default Open No authentication Open WEP Static WEP is used WPA WPA is used WPA2 Fully supports IEEE 802.11i with “TKIP/AES + 802.1X” Open For security reasons, you should NOT set security mode to Open System, since authentication and data encryption are NOT performed in Open System mode. WEP (only for legacy mode) NOTE Moxa includes WEP security mode only for legacy purposes. WEP is highly insecure and is considered fully deprecated by the Wi-Fi alliance. We do not recommend the use of WEP security under any circumstances. According to the IEEE 802.11 standard, WEP can be used for authentication and data encryption to maintain confidentiality. Shared (or Shared Key) authentication type is used if WEP authentication and data encryption are both needed. Normally, Open (or Open System) authentication type is used when WEP data encryption is run with authentication. When WEP is enabled as a security mode, the length of a key (so-called WEP seed) can be specified as 64/128 bits, which is actually a 40/104-bit secret key with a 24-bit initialization vector. The AWK-3131A-RTG provides 4 entities of WEP key settings that can be selected to use with Key index.
AWK-3131A-RTG UM Web Console Configuration 3-15 The selected key setting specifies the key to be used as a send-key for encrypting traffic from the AP side to the wireless client side. All 4 WEP keys are used as receive-keys to decrypt traffic from the wireless client side to the AP side. The WEP key can be presented in two Key types, HEX and ASCII. Each ASCII character has 8 bits, so a 40-bit (or 64-bit) WEP key contains 5 characters, and a 104-bit (or 128-bit) key has 13 characters. In hex, each character uses 4 bits, so a 40-bit key has 10 hex characters, and a 128-bit key has 26 characters. Authentication type Setting Description Factory Default Open Data encryption is enabled, but without authentication Open Shared Data encryption and authentication are both enabled. Key type Setting Description Factory Default HEX Specifies WEP keys in hex-decimal number form HEX ASCII Specifies WEP keys in ASCII form Key length Setting Description Factory Default 64 bits Uses 40-bit secret keys with 24-bit initialization vector 64 bits 128 bits Uses 104-bit secret key with 24-bit initialization vector Key index Setting Description Factory Default 1-4 Specifies which WEP key is used Open WEP key 1-4 Setting Description Factory Default ASCII type: 64 bits: 5 chars 128 bits: 13chars HEX type: 64 bits: 10 hex chars 128 bits: 26 hex chars A string that can be used as a WEP seed for the RC4 encryption engine. None WPA/WPA2-Personal WPA (Wi-Fi Protected Access) and WPA2 represent significant improvements over the WEP encryption method. WPA is a security standard based on 802.11i draft 3, while WPA2 is based on the fully ratified version of 802.11i. The initial vector is transmitted, encrypted, and enhanced with its 48 bits, twice as long as WEP. The key is regularly changed so that true session is secured. Even though AES encryption is only included in the WPA2 standard, it is widely available in the WPA security mode of some wireless APs and clients as well. The AWK-3131A-RTG also supports AES algorithms in WPA and WPA2 for better compatibility. Personal versions of WPA/WPA2, also known as WPA/WPA-PSK (Pre-Shared Key), provide a simple way of encrypting a wireless connection for high confidentiality. A Passphrase is used as a basis for encryption methods (or cipher types) in a WLAN connection. The passphrases should be complicated and as long as possible. There must be at least 8 ASCII characters in the Passphrase, and it could go up to 63. For security reasons, this passphrase should only be disclosed to users who need it, and it should be changed regularly.
AWK-3131A-RTG UM Web Console Configuration 3-16 WPA type Setting Description Factory Default Personal Provides Pre-Shared Key-enabled WPA and WPA2 Personal Enterprise Provides enterprise-level security for WPA and WPA2 Encryption method Setting Description Factory Default TKIP** Temporal Key Integrity Protocol is enabled AES AES Advance Encryption System is enabled Mixed* Provides TKIP broadcast key and TKIP+AES unicast key for some legacy AP clients. This option is rarely used. ** This option is only available with 802.11a/b/g standard * This option is only available for legacy mode in APs and does not support AES-enabled clients. Passphrase Setting Description Factory Default 8 to 63 characters Master key to generate keys for encryption and decryption None Key renewal (for AP mode only) Setting Description Factory Default 60 to 86400 seconds (1 minute to 1 day) Specifies the time period of group key renewal 3600 (seconds) NOTE The key renewal value dictates how often the wireless AP encryption keys should be changed. The security level is generally higher if you set the key renewal value to a shorter number, which forces the encryption keys to be changed more frequently. The default value is 3600 seconds (6 minutes). Longer time periods can be considered if the line is not very busy. WPA/WPA2-Enterprise (for AP mode) By setting WPA type to Enterprise, you can use EAP (Extensible Authentication Protocol), a framework authentication protocol used by 802.1X to provide network authentication. In these Enterprise-level security modes, a back-end RADIUS (Remote Authentication Dial-In User Service) server is needed if IEEE 802.1X functionality is enabled in WPA /WPA2. The IEEE 802.1X protocol also offers the possibility of carrying out an efficient connection authentication on a large-scale network. It is not necessary to exchange keys or passphrases.
AWK-3131A-RTG UM Web Console Configuration 3-17 WPA type Setting Description Factory Default Personal Provides Pre-Shared Key-enabled WPA and WPA2 Personal Enterprise Provides enterprise-level security for WPA and WPA2 Encryption method Setting Description Factory Default TKIP** Temporal Key Integrity Protocol is enabled AES AES Advance Encryption System is enabled Mixed* Provides TKIP broadcast key and TKIP+AES unicast key for some legacy AP clients. This option is rarely used. ** This option is only available with 802.11a/b/g standard * This option is available only for legacy mode in APs and does not support AES-enabled clients. Primary/Secondary RADIUS server IP Setting Description Factory Default The IP address of RADIUS server Specifies the delegated RADIUS server for EAP None Primary/Secondary RADIUS port Setting Description Factory Default Port number Specifies the port number of the delegated RADIUS server 1812 Primary/ Secondary RADIUS shared key Setting Description Factory Default Max. of 31 characters The secret key shared between AP and RADIUS server None Key renewal Setting Description Factory Default 60 to 86400 seconds (1 minute to 1 day) Specifies the time period of group key renewal 3600 (seconds)
AWK-3131A-RTG UM Web Console Configuration 3-18 WPA/WPA2-Enterprise (for Client/Client-Router mode) When used as a client, the AWK-3131A-RTG can support three EAP methods (or EAP protocols): EAP-TLS, EAP-TTLS, and EAP-PEAP, corresponding to WPA/WPA-Enterprise settings on the AP side. Encryption method Setting Description Factory Default TKIP** Temporal Key Integrity Protocol is enabled TKIP AES Advance Encryption System is enabled **This option is only available with 802.11a/b/g standard. EAP protocol Setting Description Factory Default TLS Specifies Transport Layer Security protocol TLS TTLS Specifies Tunneled Transport Layer Security PEAP Specifies Protected Extensible Authentication Protocol, or Protected EAP Before choosing the EAP protocol for your WPA/WPA2-Enterpise settings on the client end, please contact the network administrator to make sure the system supports the protocol on the AP end. Detailed information on these three popular EAP protocols is presented in the following sections. EAP-TLS TLS is the standards-based successor to Secure Socket Layer (SSL). It can establish a trusted communication channel over a distrusted network. TLS provides mutual authentication through certificate exchange. EAP-TLS is also secure to use. You are required to submit a digital certificate to the authentication server for validation, but the authentication server must also supply a certificate. You can use Basic WLAN Setup  WLAN Certificate Settings to import your WLAN certificate and enable EAP-TLS on the client end.
AWK-3131A-RTG UM Web Console Configuration 3-19 You can check the current certificate status in Current Status if it is available. • Certificate issued to: Shows the certificate user • Certificate issued by: Shows the certificate issuer • Certificate expiration date: Indicates when the certificate has expired EAP-TTLS It is usually much easier to re-use existing authentication systems, such as a Windows domain or Active Directory, LDAP directory, or Kerberos realm, rather than creating a parallel authentication system. As a result, TTLS (Tunneled TLS) and PEAP (Protected EAP) are used to support the use of so-called “legacy authentication methods.” TTLS and PEAP work in a similar way. First, they establish a TLS tunnel (EAP-TLS for example), and validate whether the network is trustworthy with digital certificates on the authentication server. This step establishes a tunnel that protects the next step (or “inner” authentication), and consequently is sometimes referred to as “outer” authentication. The TLS tunnel is then used to encrypt an older authentication protocol that authenticates the user for the network. As you can see, digital certificates are still needed for outer authentication in a simplified form. Only a small number of certificates are required, which can be generated by a small certificate authority. Certificate reduction makes TTLS and PEAP much more popular than EAP-TLS. The AWK-3131A-RTG provides some non-cryptographic EAP methods, including PAP, CHAP, MS-CHAP, and MS-CHAP-V2. These EAP methods are not recommended for direct use on wireless networks. However, they may be useful as inner authentication methods with TTLS and PEAP.
AWK-3131A-RTG UM Web Console Configuration 3-20 Because the inner and outer authentications can use distinct user names in TTLS and PEAP, you can use an anonymous user name for the outer authentication, with the true user name only shown through the encrypted channel. Keep in mind that not all client software supports anonymous alteration. Confirm this with the network administrator before you enable identity hiding in TTLS and PEAP. TTL inner authentication Setting Description Factory Default PAP Password Authentication Protocol is used MS-CHAP-V2 CHAP Challenge Handshake Authentication Protocol is used MS-CHAP Microsoft CHAP is used MS-CHAP-V2 Microsoft CHAP version 2 is used Anonymous Setting Description Factory Default Max. of 31 characters A distinct name used for outer authentication None User name & Password Setting Description Factory Default User name and password used in inner authentication None PEAP There are a few differences in the TTLS and PEAP inner authentication procedures. TTLS uses the encrypted channel to exchange attribute-value pairs (AVPs), while PEAP uses the encrypted channel to start a second EAP exchange inside of the tunnel. The AWK-3131A-RTG provides MS-CHAP-V2 merely as an EAP method for inner authentication. Inner EAP protocol Setting Description Factory Default MS-CHAP-V2 Microsoft CHAP version 2 is used MS-CHAP-V2
AWK-3131A-RTG UM Web Console Configuration 3-21 Anonymous Setting Description Factory Default Max. of 31 characters A distinct name used for outer authentication None User name & Password Setting Description Factory Default User name and password used in inner authentication None Advanced Wireless Settings Additional wireless-related parameters are presented in this section to help you set up your wireless network in detail. Transmission Rate (for A, B, G, B/G mixed, and N modes only) Setting Description Factory Default Auto The AWK-3131A-RTG senses and adjusts the data rate automatically Auto Available rates Users can manually select a target transmission data rate Multicast Rate (for AP mode only) Setting Description Factory Default Multicast rate (6M ~ 54M) You can set a fixed multicast rate for the transmission of broadcast and multicast packets on a per-radio basis. This parameter can be useful in an environment where multicast video streaming is occurring in the wireless medium, provided that the wireless clients are capable of handling the configured rate. 6M Guard Interval Setting Description Factory Default Guard Interval Guard interval is used to ensure that distinct transmissions do 800 ns.
AWK-3131A-RTG UM Web Console Configuration 3-22 not interfere with one another. You can select the guard interval manually for Wireless-N connections. The two options are Short (400 ns) and Long (800 ns). NOTE: This function can be modified in N mode only. Maximum transmission power Setting Description Factory Default Available Power Users can manually select a target power to mask max output power. Because different transmission rates might have their own max output power, please reference product datasheet. The available setting is from 3 to 26. dBm/MHz: The density of transmission power in channel width. 12 dBm (-1 dBm/MHz) NOTE Most countries define a limit for the Equivalent Isotropically Radiated Power (EIRP) for an RF transmitting system. The EIRP should not exceed the allowed value. EIRP = transmission power + antenna gain (dBi). NOTE Transmission power indicates the maximum value of transmission power which the user plans. However, the real transmitted power depends on the radio module and some facts, such as country, regulatory limitations and data rate. Please check the Transmission power in Status > Wireless Status for a real and updated value of transmission power, which the AWK is currently using. You can refer to the related glossaries in the reference section for detailed information about the above-mentioned settings. By setting these parameters properly, you can better tune the performance of your wireless network. Beacon Interval (for AP mode only) Setting Description Factory Default Beacon Interval (40 to 1000 ms) Indicates the frequency interval of the beacon 100 (ms) DTIM Interval (for AP mode only) Setting Description Factory Default Data Beacon Rate (1 to 15) Indicates how often the AWK-3131A-RTG sends out a Delivery Traffic Indication Message 1 Fragmentation threshold Setting Description Factory Default Fragment Length (256 to 2346) Specifies the maximum size a data packet before splitting and creating another new packet 2346 RTS threshold Setting Description Factory Default RTS/CTS Threshold (256 to 2346) Determines how large a packet can be before the Access Point coordinates transmission and reception to ensure efficient communication 2346 Antenna Setting Description Factory Default A/B/Both Specifies the output antenna port. Setting “Antenna” to Auto allows 2x2 MIMO communication under 802.11n and 2T2R* Both
AWK-3131A-RTG UM Web Console Configuration 3-23 communication in legacy 802.11a/b/g modes. *Note: Different from 802.11n’s multiple spatial data stream (2x2 MIMO), which doubles the throughput, 2T2R is transmits/receives the same piece of data on both antenna ports. WMM Setting Description Factory Default Enable/Disable WMM is a QoS standard for WLAN traffic. Voice and video data will be given priority bandwidth when enabled with WMM supported wireless clients. NOTE: This setting can be enabled/disabled only in A, B, and B/G Mixed modes. For N, G/N Mixed, B/G/N Mixed, and A/N Mixed modes, this setting is enabled by default. Disable Roaming Priority (Only for AP mode) Setting Description Factory Default Priority 1/2 The roaming priority should be set based on how the radios are deployed along the trackside. Priority 1: radios along the trackside are deployed with open air radiating antennas. Priority 2: radios along the trackside are deployed with leaky feeder like coverage patterns. Due to the differences in coverage patterns between different deployment scenarios, the roaming priority you select will impact roaming performance. Priority 2 AeroLink Protection (Only for Client mode) Setting Description Factory Default Disable/L2/L3 • Enable AeroLink Protection to allow wireless clients on the same LAN network to automatically negotiate with each other and form a redundant wireless communication. For more details, see Status  AeroLink Protection Status. • Select L2 for roaming on an L2 trackside network. • Select L3 for roaming on an L3 trackside network. Disabled When L3 is selected, Virtual LAN IP and Virtual WLAN IP are shown as additional setting parameters. READ THIS BEFORE CHANGING THE DFS SETTING DFS (Dynamic Frequency Selection) is a mechanism to allow unlicensed wireless devices to share spectrum with existing radar systems by detecting radar systems and avoid causing interference with them.
AWK-3131A-RTG UM Web Console Configuration 3-24 Virtual LAN IP: This IP should be defined as the gateway IP for onboard devices so that all incoming and outgoing traffic can be routed properly via this common IP in case of any role changes of the onboard clients. All AeroLink protected clients within the same subnet need to be configured with the same virtual LAN IP. Virtual WLAN IP: This IP should be defined as the virtual gateway IP for the wayside router, which can route traffic to any onboard client regardless of the client’s home WAC. This IP only needs to be configured when different clients have to backup each other while the clients are registered to different WAC units. For the router to work properly, all clients and the wayside router will need to be configured to have this routing rule (i.e., to use this virtual WLAN IP). How AeroLink Protection Works In vehicle-to-ground applications, it is essential to minimize system downtime and maximize system availability of the train-to-ground link to ensure proper communication. Moxa’s AeroLink Protection provides a reliable wireless network-level redundancy protocol to ensure that there will always be a live onboard-to-ground link, even when failures occur: 1. Communication Failover: AeroLink Protection members can negotiate with each other to automatically elect an Active node for data communication. If the Active node is no longer capable of sending data across to its access point, it will inform other Backup nodes to resume the communication via another path. 2. Frequency-Interference Failover: This concept is similar to “Communication Failover.” If the communication frequency is interfered with and data can no longer be transmitted over the current active frequency, the connection is resumed via a backup frequency. 3. Device Failover: After handling communication and frequency failures, in order to provide a wireless network free of single points of failure, AeroLink Protection also checks the device status. If the Active node has a power failure, the Backup nodes will automatically resume the wireless communication. 4. Scalable: AeroLink Protection is designed to allow multiple backup paths, making it possible for users to realize a complete redundant wireless network free from all the above failure types. 5. Fast Recovery: In addition to maintaining a redundant wireless network, providing uninterrupted communication when a failure occurs is equally important. AeroLink Protection is designed to recover from a failure in under 300 ms. NOTE When you enable the AeroLink Protection function, management packets will be broadcast every 10 ms so that the devices can negotiate with each other. If these broadcast packets are overwhelming your network, you can disable this function Turbo Roaming Setting Description Factory Default Enable/ Disable Moxa’s Turbo Roaming can enable rapid handover when the AWK-3131A-RTG, as a client or client-router, roams among a group of APs. Disable
AWK-3131A-RTG UM Web Console Configuration 3-25 When Turbo Roaming is enabled, Turbo Roaming type, RF type, Dual link option, and Scan channels will be shown as follows. There are two options available for Turbo Roaming type; 50ms (controller-based) that only works with the RTG version of the access point and the WAC-1001 and WAC-2004, and 150ms (client-based) that supports all brands of AP. Dual link reduces the packet-loss rate when roaming between difference APs; this function only works with a single channel roaming structure. The RF type shows the current RF type that this client is using. There are three Scan channels available. Note that the Scan channels may need to be modified when the RF type is changed. (For example, channel 36 is not available in B, G, or B/G Mix mode.) If you set Turbo Roaming type to 150ms (client-based), three additional roaming parameters, Roaming threshold, Roaming difference and AP alive check for 802.11b/g (or b/a) are shown as follows: Roaming Parameters Setting Description Factory Default Roaming threshold When the current RSSI value is lower than the “roaming threshold,” the client will start the roaming process. -75 Roaming difference When the RSSI of a candidate AP is greater than “the current RSSI value plus the roaming difference,” the client will roam to this new candidate AP. 7 AP alive check When “AP alive check” is enabled, the client will actively send alive-check packets over the wireless network; APs who receive the packets will respond to indicate that they are currently available. By doing this, the client can maintain a ready list of available APs, and then quickly hand over to a new AP once it loses contact with the AP it is currently connected to. -82
AWK-3131A-RTG UM Web Console Configuration 3-26 Roaming Threshold Concept T1 = Probing for new AP candidate to connect (background scan) T2 = At this point is when the roaming difference conditions are met and the client will initiate the roaming T3 = At this point the client has successfully roamed over to the new AP2 NOTE When 50 ms Turbo Roaming is enabled without using the WAC-1001 or WAC-2004, the connection between the AP and client will not work. WLAN Certification Settings (Only For EAP-TLS in Client Mode) When EAP-TLS is used, a WLAN Certificate will be required at the client end to support WPA/WPA2-Enterprise. The AWK-3131A-RTG can support the PKCS #12, also known as Personal Information Exchange Syntax Standard, certificate formats that define file formats commonly used to store private keys with accompanying public key certificates, protected with a password-based symmetric key. Current Status displays information for the current WLAN certificate, which has been imported into the AWK-3131A-RTG. Nothing will be shown if a certificate is not available. Certificate issued to: Shows the certificate user Certificate issued by: Shows the certificate issuer Certificate expiration date: Indicates when the certificate has expired You can import a new WLAN certificate in Import WLAN Certificate by following these steps, in order: 1. Input the corresponding password (or key) in the Certificate private password field and then click Submit to set the password. 2. The password will be displayed in the Certificate private password field. Click on the Browse button in Select certificate/key file and select the certificate file.
AWK-3131A-RTG UM Web Console Configuration 3-27 3. Click Upload Certificate File to import the certificate file. If the import succeeds, you can see the information uploaded in Current Certificate. If it fails, you may need to return to step 1 to set the password correctly and then import the certificate file again. NOTE The WLAN certificate will remain after the AWK-3131A-RTG reboots. Even though it has expired, it can still be seen on the Current Certificate. WAC Settings (AP Mode Only) Controller-based Turbo Roaming function is automatically enabled when you enable the 50ms Turbo Roaming (controller-based) option on the Wireless Settings > WLAN > Basic Wireless Settings > Edit page. The Primary WAC IP address, Backup WAC IP address, and Roaming domain fields are displayed. Primary WAC IP address Setting Description Factory Default IP address Enter the IP address of the primary WAC-1001 or WAC-2004 None Backup WAC IP address Setting Description Factory Default IP address Enter the IP address of the backup WAC-1001 or WAC-2004 None Primary WAC IP address Setting Description Factory Default 6 Hex characters Specifies the area served by the WAC-1001 or WAC-2004. All related controllers, APs, and clients use this IP address as identification to work and communicate with each other. None Advanced Settings Several advanced functions are available to increase the functionality of your AWK-3131A-RTG and wireless network system. A VLAN is a collection of clients and hosts grouped together as if they were connected to the broadcast domains in a layer-2 network. The DHCP server helps you deploy wireless clients efficiently. Packet filters provide security mechanisms, such as firewalls, in different network layers. Moreover, the
AWK-3131A-RTG UM Web Console Configuration 3-28 AWK-3131A-RTG can support STP/RSTP protocol to increase reliability across the entire network, and SNMP support can make network management easier. Using Virtual LAN Setting up Virtual LANs (VLANs) on your AWK series increases the efficiency of your network by dividing the LAN into logical segments, as opposed to physical segments. In general, VLANs are easier to manage. The Virtual LAN (VLAN) Concept What is a VLAN? A virtual LAN, commonly known as a VLAN, is a group of hosts with a common set of requirements that communicate as if they were attached to the same broadcast domain, regardless of their physical location. A VLAN has the same attributes as a physical LAN, but it allows for end stations to be grouped together even if they are not located on the same network switch. Network reconfiguration can be done through software instead of physically relocating devices. VLANs now extend as far as the reach of the access point signal. Clients can be segmented into wireless sub-networks via SSID and VLAN assignment. A Client can access the network by connecting to an AP configured to support its assigned SSID/VLAN. Benefits of VLANs VLANs are used to conveniently, efficiently, and easily manage your network in the following ways: • Manage adds, moves, and changes from a single point of contact • Define and monitor groups • Reduce broadcast and multicast traffic to unnecessary destinations • Improve network performance and reduce latency • Increase security • Secure network restricts members to resources on their own VLAN • Clients roam without compromising security VLAN Workgroups and Traffic Management The AP assigns clients to a VLAN based on a Network Name (SSID). The AP can support up to 9 SSIDs per radio interface, with a unique VLAN configurable per SSID. The AP matches packets transmitted or received to a network name with the associated VLAN. Traffic received by a VLAN is only sent on the wireless interface associated with that same VLAN. This eliminates unnecessary traffic on the wireless LAN, conserving bandwidth and maximizing throughput. In addition to enhancing wireless traffic management, the VLAN-capable AP supports easy assignment of wireless users to workgroups. In a typical scenario, each user VLAN represents a department workgroup; for example, one VLAN could be used for a marketing department and the other for a human resource department. In this scenario, the AP would assign every packet it accepted to a VLAN. Each packet would then be identified as marketing or human resource, depending on which wireless client received it. The AP would insert VLAN headers or “tags” with identifiers into the packets transmitted on the wired backbone to a network switch.
AWK-3131A-RTG UM Web Console Configuration 3-29 Finally, the switch would be configured to route packets from the marketing department to the appropriate corporate resources such as printers and servers. Packets from the human resource department could be restricted to a gateway that allowed access to only the Internet. A member of the human resource department could send and receive e-mail and access the Internet, but would be prevented from accessing servers or hosts on the local corporate network. Configuring Virtual LAN VLAN Settings To configure the AWK’s VLAN, use the VLAN Setting page to configure the ports. Management VLAN ID Setting Description Factory Default VLAN ID ranges from 1 to 4094 Set the management VLAN of this AWK. 1 Port Type Description Trunk Port LAN This port is the LAN port on the AWK. Yes WLAN This is a wireless port for the specific SSID. This field will refer to the SSID that you have created. If more SSIDs have been created, new rows will be added. Port PVID Setting Description Factory Default VLAN ID ranging from 1 to 4094 Set the port’s VLAN ID for devices that connect to the port. The port can be a LAN port or WLAN ports. 1 VLAN Tagged Setting Description Factory Default A comma-separated list of VLAN IDs. Each of the VLAN IDs range from 1 to 4094. For example: 1,2,3,4. Specify which VLANs can communicate with this specific VLAN. (Empty)
AWK-3131A-RTG UM Web Console Configuration 3-30 DHCP Server DHCP (Dynamic Host Configuration Protocol) is a networking protocol that allows administrators to assign temporary IP addresses to network computers by “leasing” an IP address to a user for a limited amount of time, instead of assigning permanent IP addresses. The AWK-3131A-RTG can act as a simplified DHCP server and easily assign IP addresses to your DHCP clients by responding to the DHCP requests from the client ends. The IP-related parameters you set on this page will also be sent to the client. You can also assign a static IP address to a specific client by entering its MAC address. The AWK-3131A-RTG provides a Static DHCP mapping list with up to 16 entities. Be reminded to check the Active check box for each entity to activate the setting. You can check the IP assignment status under Status  DHCP Client List. DHCP server Setting Description Factory Default Enable Enables AWK-3131A-RTG as a DHCP server Disable Disable Disable DHCP server function Default gateway Setting Description Factory Default IP address of a default gateway The IP address of the router that connects to an outside network None NOTE The VLAN feature can allow wireless clients to manage the AP. If the VLAN Management ID matches a VLAN ID, then those wireless clients who are members of that VLAN will have AP management access. CAUTION: Once a VLAN Management ID is configured and is equivalent to one of the VLAN IDs on the AP, all members of that User VLAN will have management access to the AP. Be careful to restrict VLAN membership to those with legitimate access to the AP.
AWK-3131A-RTG UM Web Console Configuration 3-31 Subnet mask Setting Description Factory Default subnet mask Identifies the type of sub-network (e.g., 255.255.0.0 for a Class B network, or 255.255.255.0 for a Class C network) None Primary/ Secondary DNS server Setting Description Factory Default IP address of Primary/ Secondary DNS server The IP address of the DNS Server used by your network. After entering the DNS Server’s IP address, you can use URL as well. The Secondary DNS server will be used if the Primary DNS server fails to connect. None Start IP address Setting Description Factory Default IP address Indicates the IP address which AWK-3131A-RTG can start assigning None Maximum number of users Setting Description Factory Default 1–128 users Specifies how many IP address can be assigned continuously None Client lease time Setting Description Factory Default 5-1440 minutes The lease time for which an IP address is assigned. The IP address may go expired after the lease time is reached. 5 (minutes) Packet Filters The AWK-3131A-RTG includes various filters for IP-based packets going through LAN and WLAN interfaces. You can set these filters as a firewall to help enhance network security. MAC Filter The AWK-3131A-RTG’s MAC filter is a policy-based filter that can allow or filter out IP-based packets with specified MAC addresses. The AWK-3131A-RTG provides 8 entities for setting MAC addresses in your filtering policy. Remember to check the Active check box for each entity to activate the setting. Enable Setting Description Factory Default Enable Enables MAC filter Disable Disable Disables MAC filter Policy Setting Description Factory Default Accept Only the packets fitting the entities on list can be allowed. Drop Drop Any packet fitting the entities on list will be denied.
AWK-3131A-RTG UM Web Console Configuration 3-32 IP Protocol Filter The AWK-3131A-RTG’s IP protocol filter is a policy-based filter that can allow or filter out IP-based packets with specified IP protocol and source/destination IP addresses. The AWK-3131A-RTG provides 8 entities for setting IP protocol and source/destination IP addresses in your filtering policy. Four IP protocols are available: All, ICMP, TCP, and UDP. You must specify either the Source IP or the Destination IP. By combining IP addresses and netmasks, you can specify a single IP address or a range of IP addresses to accept or drop. For example, “IP address 192.168.1.1 and netmask 255.255.255.255” refers to the sole IP address 192.168.1.1. “IP address 192.168.1.1 and netmask 255.255.255.0” refers to the range of IP addresses from 192.168.1.1 to 192.168.1.255. Remember to check the Active check box for each entity to activate the setting. Enable Setting Description Factory Default Enable Enables IP protocol filter Disable Disable Disables IP protocol filter Policy Setting Description Factory Default Accept Only the packets fitting the entities on the list can be allowed Drop Drop Any packet fitting the entities on the list will be denied TCP/UDP Port Filter The AWK-3131A-RTG’s TCP/UDP port filter is a policy-based filter that can allow or filter out TCP/UDP-based packets with a specified source or destination port. The AWK-3131A-RTG provides 8 entities for setting the range of source/destination ports of a specific protocol. In addition to selecting TCP or UDP protocol, you can set either the source port, destination port, or both. The end port can be left empty if only a single port is specified. Of course, the end port cannot be larger than the start port. The Application name is a text string that describes the corresponding entity with up to 31 characters. Remember to check the Active check box for each entity to activate the setting. ATTENTION Be careful when you enable the filter function: Drop + “no entity on list is activated” = all packets are allowed Accept + “no entity on list is activated” = all packets are denied ATTENTION Be careful when you enable the filter function: Drop + “no entity on list is activated” = all packets are allowed. Accept + “no entity on list is activated” = all packets are denied.
AWK-3131A-RTG UM Web Console Configuration 3-33 Enable Setting Description Factory Default Enable Enables the TCP/UDP port filter Disable Disable Disables the TCP/UDP port filter Policy Setting Description Factory Default Accept Only the packets fitting the entities on list can be allowed. Drop Drop Any packet fitting the entities on list will be denied. Static Route (For Client-Router Mode Only) The Static Routing page is used to configure AWK-3131A-RTG’s static routing table. Active Click the checkbox to enable Static Routing. Destination You can specify the destination IP address. Netmask This option is used to specify the subnet mask for this IP address. Gateway The IP address of the router that connects the LAN to an external network. Metric Use this option to specify a “cost” for accessing the neighboring network. Interface You can select which interface does your routing rules would be set. ATTENTION Be careful when you enable the filter function: Drop + “no entity on list is activated” = all packets are allowed Accept + “no entity on list is activated” = all packets are denied
AWK-3131A-RTG UM Web Console Configuration 3-34
AWK-3131A-RTG UM Web Console Configuration 3-35 NAT Settings/Port Forwarding (For Client-Router Mode Only) Network Address Translation (NAT)—or more specifically, one-to-many NAT, NAPT, or PAT—is supported to facilitate the Client-Router operation mode. This feature translates the out-going communication from multiple private IPs to a single external IP (WLAN IP) with randomly assigned port for return traffic. Port Forwarding is needed to allow external devices to initiate communication. Port Forwarding specifies a static map between external ports (WAN Port) and internal IP/port combos (LAN IP/LAN Port) Enabling NAT and Port Forwarding provides the following benefits: • Uses the NAT function to hide the Internal IP address of a critical network or device to increase the level of security of industrial network applications. • Uses the same private IP address for different, but identical, groups of Ethernet devices. For example, 1-to-1 NAT makes it easy to duplicate or extend identical production lines
AWK-3131A-RTG UM Web Console Configuration 3-36 NAT Setting Description Factory Default Enable/Disable Enables or disables the NAT translation Disable Port Forwarding Active: Click the checkbox to enable Port Forwarding rule(s). Protocol: Specifies the communication protocol. WAN Port: Specifies the external port to be forwarded to. LAN IP: Specifies the “forward to” LAN IP. LAN Port: Specifies the “forward to” LAN Port. SNMP Agent The AWK-3131A-RTG supports SNMP V1/V2c/V3. SNMP V1 and SNMP V2c use a community string match for authentication, which means that SNMP servers access all objects with read-only or read/write permissions using the community string public/private (default value). SNMP V3, which requires you to select an authentication level of MD5 or SHA, is the most secure protocol. You can also enable data encryption to enhance data security. The AWK-3131A-RTG’s MIB can be found in the software CD and supports reading the attributes via SNMP. (Only get method is supported.) SNMP security modes and security levels supported by the AWK-3131A-RTG are shown in the following table. Select the security mode and level that will be used to communicate between the SNMP agent and manager. Protocol Version Setting on UI web page Authentication Type Data Encryption Method SNMP V1, V2c V1, V2c Read Community Community string No Use a community string match for authentication V1, V2c Write/Read Community Community string No Use a community string match for authentication SNMP V3 No-Auth No No Use account with admin or user to access objects MD5 or SHA Authentication based on MD5 or SHA No Provides authentication based on HMAC-MD5, or HMAC-SHA algorithms. 8-character passwords are the minimum requirement for authentication. MD5 or SHA Authentication based on MD5 or SHA Data encryption key Provides authentication based on HMAC-MD5 or HMAC-SHA algorithms, and data encryption key. 8-character passwords and a data encryption key are the minimum requirements for authentication and encryption. The following parameters can be configured on the SNMP Agent page. A more detailed explanation of each parameter is given below:
AWK-3131A-RTG UM Web Console Configuration 3-37 Enable Setting Description Factory Default Enable Enables SNMP Agent Disable Disable Disables SNMP Agent Remote Management Setting Description Factory Default Enable Allow remote management via SNMP agent Disable Disable Disallow remote management via SNMP agent Read community (for V1, V2c) Setting Description Factory Default V1, V2c Read Community Use a community string match with a maximum of 31 characters for authentication. This means that the SNMP agent can access all objects with read-only permissions using this community string. public Write community (for V1, V2c) Setting Description Factory Default V1, V2c Read /Write Community Use a community string match with a maximum of 31 characters for authentication. This means that the SNMP agent can accesses all objects with read/write permissions using this community string. private SNMP agent version Setting Description Factory Default V1, V2c, V3, or V1, V2c, or V3 only Select the SNMP protocol version used to manage the switch. V1, V2c Admin auth type (for V1, V2c, V3, and V3 only) Setting Description Factory Default No Auth Use admin account to access objects. No authentication No Auth MD5 Provide authentication based on the HMAC-MD5 algorithms. 8-character passwords are the minimum requirement for authentication. SHA Provides authentication based on HMAC-SHA algorithms. 8-character passwords are the minimum requirement for authentication.
AWK-3131A-RTG UM Web Console Configuration 3-38 Admin private key (for V1, V2c, V3, and V3 only) Setting Description Factory Default Disable No data encryption Disable DES DES-based data encryption AES AES-based data encryption Private key A data encryption key is the minimum requirement for data encryption (maximum of 63 characters) Private MIB Information Device Object ID Also known as the OID, this is the AWK-3131A-RTG’s enterprise value and is a fixed value. Mobile IP Settings The mobile IP technology enables the AWK-3131A-RTG to roam between Layer 3 networks with a roaming break time less than 50 ms. When the AWK-3131A-RTG is in client/client router mode, it is a mobile node (MN) that is able to roam across different subnets without changing its IP address. Mobile IP Topology Example: Terminology Description Mobile Node (MN) A host or router that changes its location from one network to another. Home network The network within which the MN receives its identifying IP address (home address) Home address The IP address assigned to the MN within its home network Foreign network The network in which an MN is operating when away from its home network Home agent (HA) A router on the home network that provides services to the MN. The home agent intercepts packets sent to the MN within the home network, encapsulates them, and then tunnels them to the MN. Correspondent Node (CN) A peer with which a mobile node is communicating Co-located Care-of Address (CCoA) The new IP address of the MN when operating on a foreign network. Binding The association of the home address with a CCoA
AWK-3131A-RTG UM Web Console Configuration 3-39 Setting Description Factory Default Mobile IP Enable/disable mobile IP capability of the client (mobile node) for L3 controller based roaming Disable Subnet Binding Define a subnet of devices connected behind the client (MN) so that data will be forwarded to the corresponding device subnets. Proper IP planning is required to avoid configuring the subnet binding IP to limit access to the AWK. Disable Note that when the Mobile IP is enabled, the corresponding AP and WAC (HA) controller will also need to be configured properly (with 50 ms roaming enabled) to ensure correct operation of the L3 roaming network. Link Fault Pass-Through (For Client Mode Only) This function means if Ethernet port is link down, wireless connection will be forced to disconnect. Once Ethernet link is recovered, AWK will try to connect to AP. If wireless is disconnected, AWK restarts auto-negotiation on Ethernet port but always stays in the link failure state. Once the wireless connection is recovered, AWK will try to recover the Ethernet link. System log will indicate the link fault pass-through events in addition to the original link up/down events. Link Fault Pass-Through Setting Description Factory Default Enable Enables the Link Fault Pass-Through function Disable Disable Disables the Link Fault Pass-Through function
AWK-3131A-RTG UM Web Console Configuration 3-40 Auto Warning Settings Since industrial-grade devices are often located at the endpoints of a system, these devices will not always know what is happening elsewhere on the network. This means that these devices, including wireless APs or clients, must provide system maintainers with real-time alarm messages. Even when system administrators are out of the control room for an extended period, they can still be informed of the status of devices almost instantaneously when exceptions occur. In addition to logging these events, the AWK-3131A-RTG supports different approaches to warn engineers automatically, such as SNMP trap and e-mail. It also supports two digital inputs to integrate sensors into your system to automate alarms by email. System Log System Log Event Types Detail information for grouped events is shown in the following table. You can check the box for Enable log to enable the grouped events. All default values are enabled (checked). The log for system events can be seen in Status  System Log. System-related events Event is triggered when… System restart (warm start) The AWK-3131A-RTG is rebooted, such as when its settings are changed (IP address, subnet mask, etc.). Network-related events Event is triggered when… LAN link on The LAN port is connected to a device or network. LAN link off The port is disconnected (e.g., the cable is pulled out, or the opposing device shuts down). Client joined/ left (for AP mode) A wireless client is associated or disassociated. WLAN connected to AP (for Client mode) The AWK-3131A-RTG is associated with an AP. WLAN disconnected (for Client mode) The AWK-3131A-RTG is disassociated from an AP. Config-related events Event is triggered when… Configuration Changed A configuration item has been changed. Configuration file import via Web Console The configuration file is imported to the AWK-3131A-RTG. Console authentication failure An incorrect password is entered. Firmware upgraded The AWK-3131A-RTG’s firmware is updated. Power events Event is triggered when… Power 1/2 transition (On -> Off) The AWK-3131A-RTG is powered down in PWR1/2. PoE transition (On -> Off) The AWK-3131A-RTG is powered down in PoE. Power 1/2 transition (Off -> On) The AWK-3131A-RTG is powered via PWR1/2. PoE transition (Off -> On) The AWK-3131A-RTG is powered via PoE. DI events Event is triggered when… DI0/DI1 (On -> Off) Digital Input 0/1 is triggered by on-to-off transition. DI0/DI1 (Off -> On) Digital Input 0/1 is triggered by off-to-on transition.
AWK-3131A-RTG UM Web Console Configuration 3-41 Syslog This function provides the event logs for the Syslog server. The function supports up to three configurable Syslog servers and Syslog server UDP port numbers. When an event occurs, the event will be sent as a Syslog UDP packet to the specified Syslog servers. Syslog Event Types Detail information for the grouped events is shown in the following table. You can check the box for Enable log to enable the grouped events. All default values are enabled (checked). Details for each event group can be found on the “System log Event Types” table on page 3-31. NOTE The RSSI report events option is only supported in client mode. Syslog Server Settings You can configure the parameters for your Syslog servers in this page. Syslog server 1/ 2/ 3 Setting Description Factory Default IP address Enter the IP address of the 1st/ 2nd/ 3rd Syslog Server None Syslog port Setting Description Factory Default Port destination (1 to 65535) Enter the UDP port of the corresponding Syslog server 514
AWK-3131A-RTG UM Web Console Configuration 3-42 E-mail E-mail Event Types Check the box for Active to enable the event items. All default values are deactivated (unchecked). Details for each event item can be found on the “System log Event Types” table on page 3-31. E-mail Server Settings You can set up to 4 e-mail addresses to receive alarm emails from the AWK-3131A-RTG. The following parameters can be configured on the E-mail Server Settings page. In addition, a Send Test Mail button can be used to test whether the Mail server and e-mail addresses work well. More detailed explanations about these parameters are given after the following figure. Mail server (SMTP) Setting Description Factory Default IP address The IP Address of your email server. None
AWK-3131A-RTG UM Web Console Configuration 3-43 User name & Password Setting Description Factory Default User name and password used in the SMTP server None From e-mail address Setting Description Factory Default Max. 63 characters Enter the administrator’s e-mail address which will be shown in the “From” field of a warning e-mail. None To E-mail address 1/ 2/ 3/ 4 Setting Description Factory Default Max. 63 characters Enter the receivers’ e-mail addresses. None Traps Traps can be used to signal abnormal conditions (notifications) to a management station. This trap-driven notification can make your network more efficient. Because a management station usually takes care of a large number of devices that have a large number of objects, it will be overloading for the management station to poll or send requests to query every object on every device. It would be better if the managed device agent could notify the management station by sending a message known as a trap for the event. Trap Event Types
AWK-3131A-RTG UM Web Console Configuration 3-44 SNMP Trap Receiver Settings SNMP traps are defined in SMIv1 MIBs (SNMPv1) and SMIv2 MIBs (SNMPv2c). The two styles are basically equivalent, and it is possible to convert between the two. You can set the parameters for SNMP trap receivers through the web page. 1st / 2nd Trap version Setting Description Factory Default V1 SNMP trap defined in SNMPv1 V1 V2 SNMP trap defined in SNMPv2 1st / 2nd Trap server IP/name Setting Description Factory Default IP address or host name Enter the IP address or name of the trap server used by your network. None 1st / 2nd Trap community Setting Description Factory Default Max. of 31 characters Use a community string match with a maximum of 31 characters for authentication. alert
AWK-3131A-RTG UM Web Console Configuration 3-45 Status Wireless Status The status for 802.11 info parameters, such as Operation mode and Channel, are shown on the Wireless Status page. The status will refresh every 5 seconds if the Auto refresh box is checked. Depending on the operation mode, certain 802.11 info values may not be displayed. For example, the Current BSSID and Signal strength parameters are not available in the AP mode. It is helpful to use the continuously updated information on this page, such as Signal strength, to monitor the signal strength of the AWK-3131A-RTG in Client mode. The transmission power indicated is the current transmission power being updated periodically. Associated Client List (For AP Mode Only) Associated Client List shows all the clients that are currently associated to a particular AWK-3131A-RTG. You can click Select all to select all the content in the list for further editing. You can click Refresh to refresh the list.
AWK-3131A-RTG UM Web Console Configuration 3-46 DHCP Client List The DHCP Client List shows all the clients that require and have successfully received IP assignments. You can click the Refresh button to refresh the list. You can press Select all button to select all content in the list for further editing. System Log Triggered events are recorded in System Log. You can export the log contents to an available viewer by clicking Export Log. You can use the Clear Log button to clear the log contents and the Refresh button to refresh the log.
AWK-3131A-RTG UM Web Console Configuration 3-47 Relay Status The status of user-configurable events can be found under Relay Status. The status will refresh every 5 seconds if the Auto refresh box is checked. If an event is triggered, it will be noted on this list. System administrators can click Acknowledge Event when they have acknowledged the event and addressed it. DI and Power Status The status of power inputs and digital inputs is shown here. The status will refresh every 5 seconds if the Auto refresh box is checked. AeroLink Protection Status (For Client Mode Only) After enabling AeroLink Protection from the Advanced WLAN Setup panel, the following table shows the current state of the AeroLink Protection for easier diagnosis. An AeroLink Protection member could be in 1 or 7 different states: Initiation State (Init): Initiates the AeroLink Protection Protocol. Discovering State (Discover): Discovers other AeroLink Protection members for further negotiation. Idle State (Idle): Internal protocol checkpoint. Negotiation State (Nego): Negotiates with other AeroLink Protection members and selects Active node. Backup State (Backup): After negotiation, this node is assigned as the Backup node. All traffic will pass through the Active node. NOTE: When a node is acting as a Backup node, the STATE LED for the node will blink to advertise this fact to nearby support engineers. Active State (Active): After negotiation, this node is assigned Active node status, which means that all traffic will pass through that node.
AWK-3131A-RTG UM Web Console Configuration 3-48 Role Change State (Change): If the Active node is no longer capable of data transmission via the WLAN, the device will enter “change state,” which will result in the device going back to Nego state (likely becoming the Backup device since the active link is down). Routing Table The Routing Table page shows all routing entries. LAN Status The LAN Status page shows the LAN information, which includes speed, duplex, link status, and packet status. Maintenance Maintenance functions provide the administrator with tools to manage the AWK-3131A-RTG and wired/wireless networks. Console Settings You can enable or disable access permission for the following consoles: HTTP, HTTPS, Telnet, and SSH connections. For more security, we recommend you only allow access to the two secured consoles, HTTPS and SSH.
AWK-3131A-RTG UM Web Console Configuration 3-49 Ping Ping helps to diagnose the integrity of wired or wireless networks. By inputting a node’s IP address in the Destination field, you can use the ping command to make sure it exists and whether or not the access path is available. If the node and access path are available, you will see that all packets were successfully transmitted with no loss. Otherwise, some, or even all, packets may get lost, as shown in the following figure. Firmware Upgrade The AWK-3131A-RTG can be enhanced with more value-added functions by installing firmware upgrades. The latest firmware is available at Moxa’s download center. Before running a firmware upgrade, make sure the AWK-3131A-RTG is off-line. Click the Browse button to specify the firmware image file and click Firmware Upgrade and Restart to start the firmware upgrade. After the progress bar reaches 100%, the AWK-3131A-RTG will reboot itself. When upgrading your firmware, the AWK-3131A-RTG’s other functions are forbidden. ATTENTION Please make sure the power source is stable when you upgrade your firmware. An unexpected power breakup may damage your AWK-3131A-RTG.
AWK-3131A-RTG UM Web Console Configuration 3-50 Config Import/Export You can back up and restore the AWK-3131A-RTG’s configuration with Config Import and Config Export functions. In the Config Import section, click Browse to specify the configuration file and click on the Config Import button to begin importing the configuration. Downloading the Configuration from a TFTP Server You can download a configuration file from a TFTP server on to your AWK-3131A-RTG as follows: 1. Start your TFTP server. 2. Copy the AWK-3131A-RTG configuration file to a folder on the TFTP server. 3. On the AWK-3131A-RTG Config Import page, input your TFTP server IP and Configuration path. NOTE The configuration path is the path of the configuration file, which is a relative path. If your configuration file is already available in a folder on the TFTP server, you can leave this field blank. 4. Input your configuration File name with the filename extension or click on the Config Import button to browse to the file. Once the configuration downloads successful, you will see "TFTP import success" information on the web page. 5. Click Save and then Restart on the top-right side. You can also back up or restore the ABC-01 configuration with Config Import Export.
AWK-3131A-RTG UM Web Console Configuration 3-51 You can also get the SNMP MIB file by clicking on MIB Export in the SNMP MIB file Export section. SNMP MIB file for AWK-3131A-RTG is embedded in the device. To export the MIB file, simply click on the “MIB Export” button and save it to your local drive. Load Factory Default Use this function to reset the AWK-3131A-RTG and roll all settings back to the factory or customized (using imported configuration file in the Default Config Import screen) default values. You can also reset the hardware by pressing the reset button on the bottom panel of the AWK-3131A-RTG. Username/Password You can change the administration username and password for each of the AWK-3131A-RTG’s console managers by using the Username/Password function. Before you set up a new password, you must input the current password and reenter the new password for confirmation. For your security, do not use the default password moxa, and remember to change the administration password regularly. Locate Device The AP can be identified by a beeping sound and flashing LED when clicking on the “start to locate” button. To stop the beeping, click on the “stop locating” button.
AWK-3131A-RTG UM Web Console Configuration 3-52 Misc. Settings Additional settings to help you manage your AWK-3131A-RTG are available on this page. Reset button Setting Description Factory Default Always enable The AWK-3131A-RTG’s reset button works normally. Always enable Always disable The AWK-3131A-RTG’s reset button will not work. Disable ‘restore to default function’ after 60 sec The AWK-3131A-RTG’s reset to default function will be inactive 60 seconds after the AWK-3131A-RTG finishes booting up. Save Configuration The following figure shows how the AWK-3131A-RTG stores the setting changes into volatile and non-volatile memory. All data stored in volatile memory will disappear when the AWK-3131A-RTG is shutdown or rebooted unless they are y. Because the AWK-3131A-RTG starts up and initializes with the settings stored in flash memory, all new changes must be saved to flash memory before restarting the AWK-3131A-RTG. This also means the new changes will not work unless you run either the Save Configuration function or the Restart function. After you click on Save Configuration in the left menu box, the following screen will appear. Click Save if you wish to update the configuration settings in the flash memory at this time. Alternatively, you may choose to run other functions and put off saving the configuration until later. However, the new setting changes will remain in the non-volatile memory until you save the configurations.
AWK-3131A-RTG UM Web Console Configuration 3-53 Restart If you submitted configuration changes, you will find a blinking string in the upper right corner of the screen. After making all your changes, click the Restart function in the left menu box. One of two different screens will appear. If you made changes recently but did not save, you will be given two options. Clicking the Restart button here will reboot the AWK-3131A-RTG directly, and all setting changes will be ignored. Clicking the Save and Restart button will apply all setting changes and then reboot the AWK-3131A-RTG. If you run the Restart function without changing any configurations or saving all your changes, you will see just one Restart button on your screen. You will not be able to run any of the AWK-3131A-RTG’s functions while the system is rebooting. Logout Logout helps users disconnect the current HTTP or HTTPS session and go to the Login page. For security reasons, we recommend you logout before quitting the console manager.
4 Software Installation and Configuration The following topics are covered in this chapter:  Overview  Wireless Search Utility  Installing Wireless Search Utility  Configuring Wireless Search Utility
AWK-3131A-RTG UM Software Installation and Configuration 4-2 Overview The Wireless Search Utility can be downloaded from the Moxa website at www.moxa.com. Wireless Search Utility Installing Wireless Search Utility Once the Wireless Search Utility is downloaded, run the setup executable to start the installation. 1. Click Next in the Welcome screen to proceed with the installation.
AWK-3131A-RTG UM Software Installation and Configuration 4-3 2. Click Next to install program files to the default directory, or click Browse to select an alternate location. 3. Click Next to install the program’s shortcut files in the default directory, or click Browse to select an alternate location.
AWK-3131A-RTG UM Software Installation and Configuration 4-4 4. Click Next to select additional tasks. 5. Click Install to proceed with the installation. The installer then displays a summary of the installation options. 6. Click Install to begin the installation. The setup window will report the progress of the installation. To change the installation settings, click Back and navigate to the previous screen.
AWK-3131A-RTG UM Software Installation and Configuration 4-5 7. Click Finish to complete the installation of Wireless Search Utility. Configuring Wireless Search Utility The Broadcast Search function is used to locate all AWK-3131A-RTG APs that are connected to the same LAN as your computer. After locating the AWK-3131A-RTG, you will be able to change its IP address. Since the Broadcast Search function searches by UDP packets and not IP address, it doesn’t matter if the AWK-3131A-RTG is configured as an AP or Client. In either case, APs and Clients connected to the LAN will be located, regardless of whether or not they are part of the same subnet as the host. 1. Start the Wireless Search Utility program. When the Login page appears, select the “Device Search only” option to search for AWKs and to view each AWK’s configuration. Select the “Device management” option to assign IPs, upgrade firmware, and locate devices.
AWK-3131A-RTG UM Software Installation and Configuration 4-6 2. Open the Wireless Search Utility and then click the Search icon. 3. The “Searching” window indicates the progress of the search. When the search is complete, all AWKs that were located will be displayed in the Wireless Search Utility window.
AWK-3131A-RTG UM Software Installation and Configuration 4-7 4. Click Locate to cause the selected device to beep. 5. Make sure your AWK is unlocked before using the search utility’s icons setting. The AWK will unlock automatically if the password is set to the default. Otherwise you must enter the new password manually. 6. Go to Tools  Login Options to manage and unlock additional AWKs.
AWK-3131A-RTG UM Software Installation and Configuration 4-8 7. Use the scroll down list to select the MAC addresses of those AWKs you would like to manage, and then click Add. Key in the password for the AWK device and then click OK to save. If you return to the search page and search for the AWK again, you will find that the AWK will unlock automatically. To modify the configuration of the highlighted AWK, click on the Web icon to open the web console. This will take you to the web console, where you can make all configuration changes. Refer to Chapter 3, “Using the Web Console,” for information on how to use the web console. ATTENTION For security purposes, we suggest you can change the wireless search utility login password instead of using the default.
AWK-3131A-RTG UM Software Installation and Configuration 4-9 Click on Telnet if you would like to use telnet to configure your AWKs. Click Assign IP to change the IP setting.
AWK-3131A-RTG UM Software Installation and Configuration 4-10 The three advanced options—Search, Connection, and Miscellaneous—are explained below: Search • Retry count (default=5): Indicates how many times the search will be retried automatically. • Retry interval (ms): The time elapsed between retries. Connection • Connection timeout (secs): Use this option to set the waiting time for the Default Login, Locate, Assign IP, Upload Firmware, and Unlock to complete. • Upgrade timeout (secs): Use this option to set the waiting time for the connection to disconnect while the firmware is upgrading. Use this option to set the waiting time for the Firmware to write to flash.
AWK-3131A-RTG UM Software Installation and Configuration 4-11 Misc. Search on start: Checkmark this box if you would like the search function to start searching for devices after you log in to the Wireless Search Utility.
5 Using Other Consoles This chapter explains how to access the AWK-3131A-RTG for the first time. In addition to HTTP access, there are four ways to access the AWK-3131A-RTG: USB console, Telnet console, SSH console, and HTTPS console. The USB console connection method, which requires using a short USB cable to connect the AWK-3131A-RTG to a PC’s COM port, can be used if you do not know the AWK-3131A-RTG’s IP address. The other consoles can be used to access the AWK-3131A-RTG over an Ethernet LAN, or over the Internet. The following topics are covered in this chapter:  USB Console Configuration (115200, None, 8, 1, VT100)  Configuration via Telnet and SSH Consoles  Configuration by Web Browser with HTTPS/SSL  Disabling Telnet and Browser Access
AWK-3131A-RTG UM Using Other Consoles 5-2 USB Console Configuration (115200, None, 8, 1, VT100) The serial console connection method, which requires using a short serial cable to connect the AWK-3131A-RTG to a PC’s COM port, can be used if you do not know the AWK-3131A-RTG’s IP address. It is also convenient to use USB console configurations when you cannot access the AWK-3131A-RTG over Ethernet LAN, such as in the case of LAN cable disconnections or broadcast storming over the LAN. NOTE We recommend using the Moxa PComm (Lite) Terminal Emulator, which is available for download at: http://www.moxa.com/product/download_pcommlite_info.htm. Before running PComm Terminal Emulator, use a RJ45 to DB9-F (or RJ45 to DB25-F) cable to connect the AWK-3131A-RTG’s RS-232 console port to your PC’s COM port (generally COM1 or COM2, depending on how your system is set up). After installing PComm Terminal Emulator, take the following steps to access the RS-232 console utility. 1. From the Windows desktop, open the Start menu and run the PComm Terminal Emulator from the PComm (Lite) group. 2. In the Port Manager menu, select Open to open a new connection. 3. The Communication Parameter page of the Property window opens. Select the appropriate COM port for Console Connection, 115200 for Baud Rate, 8 for Data Bits, None for Parity, and 1 for Stop Bits. Click on the Terminal tab, and select VT100 (or ANSI) for Terminal Type. Click on OK to continue. ATTENTION Do not use the RS-232 console manager when the AWK-3131A-RTG is powered at reversed voltage (ex. -48VDC), even though reverse voltage protection is supported. If you need to connect the RS-232 console at reversed voltage, Moxa’s TCC-82 isolator is your best solution.
AWK-3131A-RTG UM Using Other Consoles 5-3 4. The Console login screen will appear. Log into the USB console with the login name (default: admin) and password (default: moxa, if no new password is set). 5. The AWK-3131A-RTG’s device information and Main Menu will be displayed. Please follow the description on screen and select the administration option you wish to perform. NOTE To modify the appearance of the PComm Terminal Emulator window, select Edit  Font and then choose the desired formatting options. ATTENTION If you unplug the USB cable or trigger DTR, a disconnection event will be evoked to enforce logout for network security. You will need to log in again to resume operation.
AWK-3131A-RTG UM Using Other Consoles 5-4 Configuration via Telnet and SSH Consoles You may use Telnet or SSH client to access the AWK-3131A-RTG and manage the console over a network. To access the AWK-3131A-RTG’s functions over the network from a PC host that is connected to the same LAN as the AWK-3131A-RTG, you need to make sure that the PC host and the AWK-3131A-RTG are on the same logical subnet. To do this, check your PC host’s IP address and subnet mask. Follow the steps below to access the console utility via Telnet or SSH client. 1. From Windows Desktop, go to Start  Run, and then use Telnet to access the AWK-3131A-RTG’s IP address from the Windows Run window (you may also issue the telnet command from the MS-DOS prompt). 2. When using SSH client (ex. PuTTY), please run the client program (ex. putty.exe) and then input the AWK-3131A-RTG’s IP address, specifying 22 for the SSH connection port. The console login screen is displayed. Refer to the USB Console Configuration section for login and administration information. 3. Log in into the command page (default username/password is cliadmin/moxa, if no new password is set). AWK-3131A-RTG supports the CLI mode. You can use the TAB key to check a related CLI command. NOTE The AWK-3131A-RTG’s default IP address is 192.168.127.253 and the default subnet mask is 255.255.255.0 (for a Class C network). If you do not set these values properly, please check the network settings of your PC host and then change the IP address to 192.168.127.xxx and subnet mask to 255.255.255.0.
AWK-3131A-RTG UM Using Other Consoles 5-5 Configuration by Web Browser with HTTPS/SSL To secure your HTTP access, the AWK-3131A-RTG supports HTTPS/SSL encryption for all HTTP traffic. Perform the following steps to access the AWK-3131A-RTG’s web browser interface via HTTPS/SSL. 1. Open your web browser and type https://<AWK-3131A-RTG’s IP address> in the address field. Press Enter to establish the connection. 2. Click on continue to this website. The protocol in the URL changes to HTTPS. You can now enter your username and password to login into the function page.
AWK-3131A-RTG UM Using Other Consoles 5-6 Disabling Telnet and Browser Access If you are connecting the AWK-3131A-RTG to a public network but do not intend to use its management functions over the network, then we suggest disabling both Telnet Console and Web Configuration. Please run Maintenance  Console Settings to disable them, as shown in the following figure.
A References This chapter provides more detailed information about wireless-related technologies. The information in this chapter can help you manage your AWK-3131A-RTGs and plan your industrial wireless network better. The following topics are covered in this appendix:  Beacon  DTIM  Fragment  RTS Threshold  STP and RSTP  The STP/RSTP Concept  Differences between RSTP and STP
AWK-3131A-RTG UM References A-2 Beacon A beacon is a packet broadcast by the AP to keep the network synchronized. A beacon includes the wireless LAN service area, the AP address, the Broadcast destination address, a time stamp, Delivery Traffic Indicator Maps (DTIM), and the Traffic Indicator Message (TIM). Beacon Interval indicates the frequency interval of AP. DTIM Delivery Traffic Indication Map (DTIM) is contained in beacon frames. It is used to indicate that broadcast and multicast frames buffered by the AP will be delivered shortly. Lower settings result in more efficient networking, while preventing your wireless client from dropping into power-saving sleep mode. Higher settings allow your PC to enter sleep mode, thus saving power. Fragment A lower setting means smaller packets, which will create more packets for each transmission. If you have decreased this value and experience high packet error rates, you can increase it again, but it will likely decrease overall network performance. Only minor modifications of this value are recommended. RTS Threshold RTS Threshold (256-2346) – This setting determines how large a packet can be before the Access Point coordinates transmission and reception to ensure efficient communication. This value should remain at its default setting of 2,346. When you encounter inconsistent data flow, only minor modifications are recommended. STP and RSTP The STP/RSTP Concept Spanning Tree Protocol (STP) was designed to help reduce link failures in a network, and provide protection from loops. Networks that have a complicated architecture are prone to broadcast storms caused by unintended loops in the network. The STP protocol is part of the IEEE802.1D standard, 1998 Edition bridge specification. Rapid Spanning Tree Protocol (RSTP) implements the Spanning Tree Algorithm and Protocol defined by IEEE802.1w-2001 standard. RSTP provides the following benefits: • The topology of a bridged network will be determined much more quickly compared to STP. • RSTP is backward compatible with STP, making it relatively easy to deploy. For example:  Defaults to sending 802.1D-style BPDUs if packets with this format are received.  STP (802.1D) and RSTP (802.1w) can operate on the LAN ports and WLAN ports of the same AWK-3131A-RTG. This feature is particularly helpful when the AWK-3131A-RTG connects to older equipment, such as legacy switches.
AWK-3131A-RTG UM References A-3 Differences between RSTP and STP RSTP is similar to STP, but includes additional information in the BPDUs that allow each bridge to confirm that it has taken action to prevent loops from forming when it decides to enable a link to a neighboring bridge. Adjacent bridges connected via point-to-point links will be able to enable a link without waiting to ensure that all other bridges in the network have had time to react to the change. The main benefit of RSTP is that the configuration decision is made locally rather than network-wide, allowing RSTP to carry out automatic configuration and restore a link faster than STP.
B Supporting Information This chapter presents additional information about this product. You can also learn how to contact Moxa for technical support. The following topics are covered in this appendix:  Firmware Recovery  DoC (Declaration of Conformity)  Federal Communication Commission Interference Statement  RED Compliance Statement  Canada, Industry Canada (IC) Notices  Antenna Gain and RF Radiated Power  R&TTE Compliance Statement
AWK-3131A-RTG UM Supporting Information B-2 Firmware Recovery When the LEDs of FAULT, Signal Strength, CLIENT, and WLAN all light up simultaneously and blink at one-second interval, it means the system booting has failed. It may result from some wrong operation or uncontrollable issues, such as an unexpected shutdown during firmware update. The Firmware Recovery mode is designed to help administrators recover such damage and resume system operation rapidly. You can refer to the following instructions to recover the firmware: Connect to the AWK-3131A-RTG’s RS-232 console with 115200bps and N-8-1. You will see the following message shown on the terminal emulator every one second. please set-up TFTP server 192.168.127.1 contains awk3131a-rtg.rom for firmware recovery. please set-up TFTP server 192.168.127.1 contains awk3131a-rtg.rom for firmware recovery. please set-up TFTP server 192.168.127.1 contains awk3131a-rtg.rom for firmware recovery. please set-up TFTP server 192.168.127.1 contains awk3131a-rtg.rom for firmware recovery. please set-up TFTP server 192.168.127.1 contains awk3131a-rtg.rom for firmware recovery. please set-up TFTP server 192.168.127.1 contains awk3131a-rtg.rom for firmware recovery. To initiate a firmware recovery process, do the following: 1. Change the IP address of the laptop to 192.168.127.1. 2. Set up a TFTP sever on your laptop. 3. Download the AWK-3131A-RTG’s firmware from Moxa’s Website. 4. Change the firmware file name to awk3131a-rtg.rom 5. Connect to the AWK-3131A-RTG’s M12 Ethernet port or SC fiber port. If the setting is correct, you will see the following message shown on the terminal emulator, and the AWK-3131A-RTG will reboot when the firmware recovery process has finished. Trying eth0 Using eth0 device TFTP from server 192.168.127.1; our IP address is 192.168.127.253 Filename 'awk3131a-rtg.rom'. Load address: 0x80060000 Loading: *################################################################# ################################################################# #################################################################
AWK-3131A-RTG UM Supporting Information B-3 DoC (Declaration of Conformity) Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, End-users and installers must be provide with antenna installation instructions and transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Antenna List Antenna Part No. Antenna Type Maximum Antenna Gain ANT-WDB-WDB-O-2-BK Dipole Antenna 2.34 dBi for 5.25~5.35GHz 2.34 dBi for 5.47~5.725GHz ANT-WDB-ARM-0202 Dipole Antenna 1.6 dBi for 5.25~5.35 GHz 1.8 dBi for 5.47~5.725 GHz
AWK-3131A-RTG UM Supporting Information B-4 RED Compliance Statement Hereby, Moxa declares that this AWK-3131A-RTG is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The 5150 – 5350 MHz frequency range is restricted to indoor use only. Outdoor operation in this range is prohibited. Moxa declares that the apparatus AWK-3131A-RTG complies with the essential requirements and other relevant provisions of Directive 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE directive repeals and replaces the Directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) as of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the manufacturer must therefore be followed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France (with Frequency channel restrictions), Germany, Greece, Ireland, Italy, Luxembourg, Portugal, Spain, Sweden, The Netherlands, and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states Norway and Switzerland. EU Countries Not Intended for Use None. Potential Restrictive Use France: only channels 10, 11, 12, and 13. Canada, Industry Canada (IC) Notices This device complies with Industry Canada’s license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Warning: Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Canada, avis d'Industry Canada (IC) Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Devraient également être informés les utilisateurs que les radars à haute puissance sont désignés comme utilisateurs principaux (c.-à-utilisateurs prioritaires) des bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient provoquer des interférences et / ou endommager les appareils LE-LAN.
AWK-3131A-RTG UM Supporting Information B-5 Radio Frequency (RF) Exposure Information The radiated output power of this wireless device is below the Industry Canada (IC) radio frequency exposure limits. This wireless device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions (i.e., the device antennas are greater than 20 cm from a person's body). Informations concernant l'exposition aux frequences radio (RF) La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition à des appareils mobiles (antennes sont supérieures à 20 cm à partir du corps d'une personne). Antenna Gain and RF Radiated Power The following sections contain the FCC rules regarding adapting the product transmission power based on the antenna used. Antenna Part No. Antenna Type Maximum Antenna Gain ANT-WDB-WDB-O-2-BK Dipole Antenna 2.34 dBi for 5.25~5.35GHz 2.34 dBi for 5.47~5.725GHz ANT-WDB-ARM-0202 Dipole Antenna 1.6 dBi for 5.25~5.35 GHz 1.8 dBi for 5.47~5.725 GHz
AWK-3131A-RTG UM Supporting Information B-6 NCC (National Communication Commission) 本產品符合低功率電波輻射性電機管理辦法第十二條、第十四條等條文規定: 經型式認證合格之低功率射頻電機, 非經許可,公司, 商號或使用者均不得擅自變更頻率,加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航影響安全及干擾合法通信, 經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。 前項合法通信,指一電信法規定作業之無線電通信低功率射頻電機需忍受合法通信或工業,科學及醫療用電波輻射性電機設備之干擾。
AWK-3131A-RTG UM Supporting Information B-7 R&TTE Compliance Statement Moxa declares that the apparatus AWK-3131A-RTG complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) as of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacturer must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France (with Frequency channel restrictions), Germany, Greece, Ireland, Italy, Luxembourg, Portugal, Spain, Sweden, The Netherlands, and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states Norway and Switzerland. EU Countries Not Intended for Use None. Potential Restrictive Use France: only channels 10, 11, 12, and 13.

Navigation menu