Acrodyne NW8201E DIGITAL TELEVISION BROADCAST TRANSMITTER User Manual 32 NV8202 26 04 06 01 00

Download:
Mirror Download [FCC.gov]
Document ID	864582
Application ID	vnwefxrVtvE1edbLlVsrmQ==
Document Description	Users Manual Part 17
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	82.22kB (1027752 bits)
Date Submitted	2007-11-06 00:00:00
Date Available	2008-01-18 00:00:00
Creation Date	2007-11-02 12:34:26
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2007-11-02 12:37:42
Document Title	32 NV8202-26.04.06-01.00.book
Document Creator	FrameMaker 7.0
Document Author:	HUPFAUER

Chapter 8
Service
Transmitter Control Unit
You can replace the following transmitter control unit components:
 NETCCU®
 Rack controller
5.1
Replacing the NETCCU
ATTENTION!
Always make sure that the power supply is disconnected before commencing any service
work on the transmitter rack; this will prevent injury caused by electric shock and damage
to the instruments.
5.1.1
Removing the NETCCU
Note
Removing the NETCCU® does not affect transmission.
1. Switch off automatic line fuse F1.
2. Undo the two captive screws (Torx screwdriver No. 20) of both the NETCCU® and the
exciter on the front brackets (next to the handles).
3. Using the handles, slowly pull out the rackmount from the rack as far as it will go (the
guide rails will engage and lock in place).
4. Disconnect power cables at the rear of the NETCCU®.
5. Disconnect all cables at the rear of the NETCCU®.
2099.9595.72
- 8.15 -
E-2
Chapter 8
Service
Fig. 12 Removing the NETCCU from the transmitter rack
1)
2)
3)
4)
5)
Captive screws on the front panel of the built-in equipment (in this case exciter and NETCCU)
Screw-connections of the NETCCU on the rackmount
Guide rails
Support bracket for the NETCCU
Safety lever for undoing the latch of the guide rails
6. On both sides of the NETCCU® undo the two fixing screws (Phillips screwdriver No. 1)
from the rackmount.
Note
It is advisable that two persons remove the NETCCU®. As soon as the support brackets
cease to support the NETCCU® while it is being pulled out using the handles, it needs
to be supported from below.
7. Pull the NETCCU® from the rackmount.
5.1.2
Preparing the NETCCU for Installation
The replacement NETCCU® is delivered as a desktop unit and must be prepared for installation as follows.
) Remove the protective rubber caps on the rear feet of the instrument.
2099.9595.72
- 8.16 -
E-2
Chapter 8
5.1.3
Service
Installing the NETCCU
To install the amplifier in the transmitter, reverse the procedure used to remove it.
1. Slide the NETCCU® into the cabinet horizontally on the support brackets until the screw
holes on the cabinet and on the side panels of the NETCCU® match.
2. Fasten the NETCCU® with two screws on each side.
3. Connect the cables to the NETCCU® according to the labeling (see yellow cable collars).
4. Undo the latch on the guide rails. Simultaneously press down the safety lever on the
right side and up on the left side and insert the rackmount into the rack.
5. Refasten the captive screws to the front panels of the NETCCU® and the exciter.
6. Switch the NETCCU® on again.
Note
When installing the cables of the NETCCU® and putting the unit back into operation, refer
to the information in the transmitter manual.
5.2
Replacing the Rack Controller
ATTENTION!
Always make sure that the power supply is disconnected before commencing any service
work on the transmitter rack; this will prevent injury caused by electric shock and damage
to the instruments.
5.2.1
Removing the Rack Controller
Note
The rack controller is underneath the NETCCU®.
1. Remove the cover by undoing the two screws (Torx screwdriver No. 20).
2099.9595.72
- 8.17 -
E-2
Chapter 8
Service
2. Turn the two screws on the sides alternately (Torx screwdriver No. 20), a couple of turns
at a time.
This removes the rack controller from the rack without tilting.
Fig. 13 Removing the rack controller from the transmitter rack
3. Remove the rack controller from the rack.
4. Disconnect the AC supply cable and all cabling from the rear of the rack controller.
5.2.2
Installing the Rack Controller
To install the unit in the transmitter, reverse the procedure used to remove it.
Note
2099.9595.72
In the case of the cabling, note the labeling on the yellow cable collars.
- 8.18 -
E-2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2007:11:02 12:37:42-04:00
Create Date                     : 2007:11:02 12:34:26-04:00
Title                           : 32 NV8202-26.04.06-01.00.book
Author                          : HUPFAUER
Creator                         : FrameMaker 7.0
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Page Count                      : 4
Mod Date                        : 2007:11:02 12:37:42-04:00
Creation Date                   : 2007:11:02 12:34:26-04:00
Metadata Date                   : 2007:11:02 12:37:42-04:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools