Alcatel Lucent USA ONEBTS-11 UMTS-CDMA Transceiver System (850) User Manual 401703454i1

1-22 Lucent Technologies – Proprietary

See notice on first page 401-703-454

FOA Draft Issue 1

January, 2006

...........................................................................................................................................................................................................................................................

Overview of the Flexent‚ Modular Cell 4.0B cabinet

installation

Refer to Chapter 2, Heat exchanger and solar shield configurations for

Modular Cell 4.0B cabinets on Page 2 - 69 for heat exchanger and solar

shield applications for the following configurations

4.0B dual band cabinet

without integrated power in

legacy line-ups with

customer-supplied power

The following diagram shows configuration options for 4.0B dual band

cabinet without integrated power in legacy line-ups with customer-

supplied power.

Important! Within the following section, figures depicting

installation sites are provided for general information only. These

figures are not to be used as a reference for an installation. Always

use current and approved documentation, which is referenced in

the installation procedure.

FRONT OR REAR HEAT

EXCHANGER, AS APPLICABLE

1-11C

4.0B

PCS

1-11 PCS CARRIERS

5-8 850 CARRIERS

and G-1)(4.0 Primary

1-3C

1/2/3.0

850

1-3C

1/2/3.0

850

1-11C

4.0B

PCS

1-2C

4.0

850

(4.0B Dual Band)

LUCENT OR

CUSTOMER

SUPPLIED

POWER AND

BATTERY

LUCENT OR

CUSTOMER

SUPPLIED

POWER AND

BATTERY

1-11 PCS CARRIERS

7-8 850 CARRIERS

(1/2/3.0 Primary and

(4.0B Dual Band)

G-1, 4.0 G-2)

1-4Cor

1-6C

850

4.0

1-2C

850

4.0

Overview of the Flexent‚ Modular Cell 4.0B cabinet

installation

1- 23

Lucent Technologies – Proprietary

See notice on first page

401-703-454

FOA Draft Issue 1

January, 2006

............................................................................................................................................................................................................................................................

Modular Cell 4.0B primary

and dual band cabinets

with WNG24-BC battery

cabinets installed on a

concrete pad

Illustrated below is an outdoor site maximum 4.0B configuration, with

primary and dual band Modular Cell 4.0B cabinets with WNG24-BC

battery cabinets installed on a concrete pad.

NOTE: THE MODULAR CELL 4.0B CABINETS SHOWN HAVE

INTEGRATED POWER. THEY ARE ILLUSTRATED WITH A

FRONT HEAT EXCHANGER (RATHER THAN A REAR HEAT

EXCHANGER WHICH ARE USED ON CERTAIN NON-

INTEGRATED POWER CABINETS ONLY). THE SOLAR

SHIELDS ARE NOT ILLUSTRATED. Refer to Heat exchanger and

solar shield configurations for Modular Cell 4.0B cabinets ON PAGE 2 - 69

for 4.0B applications. A 4.0B DUAL BAND CABINET #2 ALSO

HAS ANTENNA JUMPER CABLES

Note that battery support for Cabinet #1 (primary) and Cabinet #2 (dual

band) must be from independent separate sources. Currently, WNG

battery cabinets may be used to support cabinet #1 (primary) only.

EZBFo frames must be used to support cabinet #2 (4.0B dual band),

but they must be installed to the right of the dual band cabinet (as

viewed from the rear). EZBFo may also be used in place of the WNG

Battery to support cabinet #1 (primary). The following (rear view) line-

ups are possible: WNG #2 - WNG #1 - Primary 4.0B - Dual Band 4.0B

- EZBFo #1 - EZBFo - #2 or EZBFo #2 - EZBFo - #1 - Primary 4.0B -

Dual Band 4.0B - EZBFo #1 - EZBFo - #2

1-24 Lucent Technologies – Proprietary

See notice on first page 401-703-454

FOA Draft Issue 1

January, 2006

...........................................................................................................................................................................................................................................................

Overview of the Flexent‚ Modular Cell 4.0B cabinet

installation

Modular Cell 4.0B primary

and dual band cabinets

with WNG24-BC battery

cabinets installed on a

rooftop

Illustrated below is an outdoor site maximum 4.0B configuration, with

primary and dual band Modular Cell 4.0B cabinets with WNG24-BC

battery cabinets installed on a rooftop.

NOTE: THE MODULAR CELL 4.0B CABINETS SHOWN HAVE

INTEGRATED POWER. THEY ARE ILLUSTRATED WITH A FRONT

HEAT EXCHANGER (RATHER THAN A REAR HEAT EXCHANGER

WHICH ARE USED ON CERTAIN NON-INTEGRATED POWER

CABINETS ONLY). THE SOLAR SHIELDS ARE NOT ILLUSTRATED.

Refer to Heat exchanger and solar shield configurations for Modular Cell

JUMPER CABLE

SUPPORT STRUCTURE

ASSEMBLY

(BY CUSTOMER)

2" CONDUIT

ASSEMBLYFOR

T1/E1 AND USER

ALARMS ( TYP )

ANTENNA

JUMPER CABLES

( TYP )

RF ANTENNA CABLES TO

ANTENNA TOWER ( TYP )

CONNECTORS ( TYP )

7/16 DIN FEMALE

2" CONDUIT ASSEMBLY

FOR AC POWER ( TYP )

REAR

MOUNTING BASE ( TYP )

( OPTIONAL )

CONCRETE PAD

(BY CUSTOMER)

WNG. BATTERY CABINET 1 *

(OPTIONAL)

WNG. BATTERY CABINET 2 *

(OPTIONAL)

1 " OPTIONAL PORTS

FOR ALARMS

CABINET 1

CABINET 2

GPS ANTENNA CABLE

SURGE

PROTECTION (TYP)

Overview of the Flexent‚ Modular Cell 4.0B cabinet

installation

1- 25

Lucent Technologies – Proprietary

See notice on first page

401-703-454

FOA Draft Issue 1

January, 2006

............................................................................................................................................................................................................................................................

4.0B cabinets ON PAGE 2 - 69 for 4.0B applications. A 4.0B DUAL

BAND CABINET #2 ALSO HAS ANTENNA JUMPER CABLES