Flir BelgiumBA DP4KW Light Marine Navigational Radar User Manual E Series Networked Display Ref Manual Part 1

Raymarine UK Ltd. Light Marine Navigational Radar E Series Networked Display Ref Manual Part 1

E Series Guide Part 1

Download: Flir BelgiumBA DP4KW Light Marine Navigational Radar User Manual E Series Networked Display Ref Manual Part 1
Mirror Download [FCC.gov]Flir BelgiumBA DP4KW Light Marine Navigational Radar User Manual E Series Networked Display Ref Manual Part 1
Document ID847004
Application ID7XZns8nBSgbm5T8EmYTxGA==
Document DescriptionE Series Guide Part 1
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize248.13kB (3101569 bits)
Date Submitted2007-09-25 00:00:00
Date Available2007-09-25 00:00:00
Creation Date2007-09-24 15:38:14
Producing SoftwareAFPL Ghostscript 8.14
Document Lastmod2007-09-24 15:38:14
Document TitleE-Series Networked Display Ref Manual Part 1.pdf
Document CreatorPDFCreator Version 0.8.0
Document Author: vina.kerai

ESeries
Networked
Display
Reference Manual
Document number: 81244_4
Date: August 2007
ESeries Reference Manual
Trademarks and registered trademarks
Autohelm, HSB, Raymarine, RayTech Navigator, Sail Pilot, SeaTalk and Sportpilot are registered
trademarks of Raymarine Limited. Apelco is a registered trademark of Raymarine Holdings Limited
(registered in all major marketing territories).
AST, Autoadapt, Auto GST, Autoseastate, Autotrim, Bidata, Marine Intelligence, Maxiview, On Board,
Raychart, Raynav, Raypilot, Raystar, ST40, ST60, Seaclutter, Smart Route, Tridata and Waypoint
Navigation are trademarks of Raymarine Limited.
Navionics is a registered trademark of Navionics Company, Italy.
All other product names are trademarks or registered trademarks of their respective owners.
Software in this product is based in part on the work of the Independent JPEG Group.
Contents of this handbook ©Raymarine plc 2006.
Copyright Notice
libwww Copyright Notice
libwww: W3C's implementation of HTTP can be found at: http://www.w3.org/Library/
Copyright © 19942000 World Wide Web Consortium, (Massachusetts Institute of Technology, Institut
National de Recherche en Informatique et en Automatique, Keio University). All Rights Reserved. This
program is distributed under the W3C's Software Intellectual Property License. This program is distributed
in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See W3C License http://www.w3.org/
Consortium/Legal/ for more details.
Copyright © 1995 CERN. "This product includes computer software created and made available by CERN.
This acknowledgment shall be mentioned in full in any product which includes the CERN computer
software included herein or parts thereof."
W3C® SOFTWARE NOTICE AND LICENSE
http://www.w3.org/Consortium/Legal/2002/copyrightsoftware20021231
1. The full text of this NOTICE in a location viewable to users of the redistributed or derivative work.
2. Any preexisting intellectual property disclaimers, notices, or terms and conditions. If none exist, the
W3C Software Short Notice should be included (hypertext is preferred, text is permitted) within the
body of any redistributed or derivative code.
3. Notice of any changes or modifications to the files, including the date changes were made. (We rec
ommend you provide URIs to the location from which the code is derived.)
THIS SOFTWARE AND DOCUMENTATION IS PROVIDED "AS IS," AND COPYRIGHT HOLDERS MAKE NO
REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO,
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE OR THAT THE USE OF
THE SOFTWARE OR DOCUMENTATION WILL NOT INFRINGE ANY THIRD PARTY PATENTS, COPYRIGHTS,
TRADEMARKS OR OTHER RIGHTS.
COPYRIGHT HOLDERS WILL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF ANY USE OF THE SOFTWARE OR DOCUMENTATION.
This formulation of W3C's notice and license became active on December 31 2002. This version removes
the copyright ownership notice such that this license can be used with materials other than those owned
by the W3C, reflects that ERCIM is now a host of the W3C, includes references to this specific dated
version of the license, and removes the ambiguous grant of "use".
Copyright status
Libwww software that was developed inside W3C will continue to be protected under the W3C Software
License. Future work on libwww will remain accessible to public and as such is protected under the W3C
Software License or a similar Open Source License, such as GPL.
Important information
Important Information
Intended use
The display units detailed in this handbook may form part of marine navigational
radar system or GPS system intended for use on (nonIMO/SOLAS class) leisure
vessels or small workboats.
This handbook contains important information on the operation and maintenance of
your ESeries Display. To get the best results in operation and performance, please
take the time to read this handbook thoroughly.
For full details of installation and system integration, please refer to the ESeries
Installation Guide supplied with the display.
Safety notices
WARNING:Navigation Aid
This device is intended to be used as an aid to navigation. Its
accuracy can be affected by many factors, including equipment
failure or defects, environmental conditions and incorrect
handling or use. It is the user’s responsibility to exercise common
prudence and navigational judgement. This device should not be
relied upon as a substitute for such prudence and judgement.
WARNING:Product installation
This equipment must be installed in accordance with the
instructions in the ESeries System Installation Guide. Failure to do
so could result in poor product performance, personal injury and/
or damage to the vessel.
WARNING:High voltage
The display unit and scanner unit contain high voltages.
Adjustments require specialized service procedures and tools only
available to qualified service technicians  there are no user
serviceable parts or adjustments. The operator should never
remove the display unit cover or attempt to service the
equipment.
WARNING:Electromagnetic energy
The radar scanner transmits electromagnetic energy. Ensure that
the scanner has been installed according to the recommendations
given in the relevant scanner handbook. Avoid looking directly at
the antenna.
ii
ESeries Networked Display Reference Manual
WARNING:Fishfinder sounder module
Removing the transducer cable from the rear of the fishfinder
sounder module whilst it is switched on can cause sparks. Only
remove the transducer cable after power has been switched off.
Ensure that the sounder module is mounted where it is well
ventilated and in an area free from flammable vapors.
CAUTION: Water Ingress
To prevent the ingress of water and consequent damage to the display,
ensure that the chart card door is firmly closed. This can be confirmed by an
audible click.
CAUTION: CompactFlash Cards
• Removing the CompactFlash card whilst information is being written to
or read from it may cause damage to the card and loss of all data. Use the
proper procedure detailed on page 20 to remove the card.
• Only one CompactFlash card per display can be used at any one time.
• Do not save data (waypoints, routes etc.) to a Navionics card as the charts
may be overwritten. When archiving use a different CompactFlash card.
• DO NOT use a metallic instrument such as a screwdriver or pliers to help you
remove a card, as doing this can cause irreparable damage.
CAUTION: Global Positioning System Antenna
Do not connect or disconnect the GPS antenna from the display unit whilst
power is switched on. Doing this may result in irreparable damage.
CAUTION: UV Light
To provide protection against the damaging effects of UV light, it is advisable
to replace the sun cover provided when the display is not in use.
CAUTION: Cleaning the display
Take care when cleaning the display, to avoid damaging it:
(1) Do NOT wipe the display screen with a dry cloth, as this could scratch
the screen coating.
(2) Do NOT use acid, ammonia based or abrasive products.
Disclaimers
Electronic charts are an aid to navigation designed to facilitate the use of authorized
government charts, not to replace them. Only official government charts and notices
to mariners contain the current information needed for safe navigation. The Captain
is responsible for their prudent use. The ESeries and its charts do not therefore
exclude the user from carrying the required official charts and documents.
Raymarine does not warrant that this product is errorfree or that it is compatible
with products manufactured by any person or entity other than Raymarine.
This product uses digital chart data, and electronic information from the Global
Positioning System (GPS) which may contain errors. Raymarine does not warrant the
accuracy of such information and you are advised that errors in such information
may cause the product to malfunction. Raymarine is not responsible for damages or
Important information
iii
injuries caused by your use or inability to use the product, by the interaction of the
product with products manufactured by others, or by errors in chart data or
information utilized by the product and supplied by third parties.
Weather services
All information presented by this service is advisory only. You acknowledge the risk
of incomplete and erroneous information and assume complete responsibility and
risks associated with this device, and accordingly release Raymarine, Sirius Satellite
Radio Inc. and WSI Corporation from any and all claims arising from the use of this
service. By using this service, you acknowledge and agree that you have read the
terms of the subscription agreement for this service and agree to all of the terms
contained therein. If you do not have the subscription agreement, you may view a
copy on the internet at www. Sirius.com/marineweatheragreement or call 1800
869_5480 for a copy to be sent to you.
About this manual
This manual describes how to operate your ESeries display in conjunction with
Navionics cartography. It assumes that all peripheral equipment to be operated with
it is compatible and has been correctly installed.
This manual is intended for users of varying marine abilities, but assumes a general
level of knowledge of display use, nautical terminology and practices.
Raymarine does not necessarily support all the features in particular Navionics
cartography.
Technical accuracy
To the best of our knowledge, the technical information contained within this
handbook, was correct at the time of printing. However, Raymarine cannot accept
liability for any inaccuracies or omissions it may contain.
In addition, Raymarine’s policy of continuous product improvement may change
specifications without notice. As a result Raymarine cannot accept liability for any
differences between the product and this handbook.
Raymarine does not support aftersales or technical support for Navionics chart
cards. If you wish to file a report of an error or omission on a Navionics chart, please
provide the information to the Navionics web site at the link below:
http://www.navionics.com/DiscrepancyReports.asp
iv
ESeries Networked Display Reference Manual
EMC conformance
All Raymarine equipment and accessories are designed to the best industry
standards for use in the recreational marine environment. Their design and
manufacture conforms to the appropriate Electromagnetic Compatibility (EMC)
standards, but correct installation is required to ensure that performance is not
compromised.
Multimedia chart cards
Navionics support
In addition to Gold and Platinum, the ESeries now supports the following Navionics
cartography:
• Silver
• Gold Plus
• HotMaps USA
• HotMaps Premium
• Fish ‘N Chip
For more information on Navionics charts, see www.navionics.com.
To use your ESeries Display as a navigation aid, charts with the appropriate level of
detail for the geographic area you wish to navigate are required. The charts are
available in electronic format on Navionics Chart cards.
To check the current availability of Navionics® chart card types and the latest
feature sets, visit www.navionics.com or www.navionics.it.
To obtain Navionics cards, contact your local dealer or visit the Navionics web site.
Alternatively, anywhere in North America call Navionics tollfree on 1800848
5896 Outside of North America, contact your local dealer or Navionics SpA on:
Phone: (+39) 0584 961696 or Fax: (+39) 0584 961309)
When archiving data, Raymarine recommends that you only use SanDisk CF memory
cards. Other brands of CF memory card may not work in your ESeries Display.
Disposal
Waste Electrical and Electronic Equipment (WEEE) Directive
The WEEE Directive requires the recycling of waste electrical and electronic
equipment. Whilst the WEEE Directive does not apply to some of
Raymarine’s products, we support its requirements as part of our
Important information
environmental policy and we ask you to be aware of how you should dispose of this
product.
The crossedout wheeled bin symbol found on our products signifies that it should
not be disposed of in general waste or landfill.
Please contact your local dealer, national distributor or Raymarine Technical Services
for information on product disposal.
vi
ESeries Networked Display Reference Manual
vii
Contents
Chapter 1:
Overview.................................................................................................. 1
1.1 What will my E-Series integrate with? ...........................................................1
1.2 What can the E-Series Display do? .................................................................2
1.3 The Simulator .................................................................................................5
Chapter 2:
General Operation .................................................................................. 7
2.1 Introduction ....................................................................................................7
2.2 Powering the display ON/OFF .......................................................................7
2.3 Using the controls ...........................................................................................8
The control panel ...................................................................................... 8
Buttons and soft keys ................................................................................ 9
The cursor ............................................................................................... 10
2.4 Displaying applications ............................................................................... 10
2.5 Additional screen information ......................................................................11
2.6 Initial setup procedures ................................................................................ 15
Selecting the data master (Networked E-Series only) ............................ 15
Setting the language, date/time format and units of measurement ......... 15
Selecting a page set ................................................................................. 16
Selecting an application page ................................................................. 16
Selecting an application window ............................................................ 17
Adjusting the display lighting ................................................................ 18
2.7 Using CompactFlash cards .......................................................................... 19
Cautions .................................................................................................. 19
What are CompactFlash cards used for? ................................................ 19
Inserting a card ....................................................................................... 20
Removing a card ..................................................................................... 20
2.8 Managing data ............................................................................................. 21
Writing/retrieving data to a CompactFlash card ..................................... 21
Sending and receiving information using a PC ...................................... 25
Password protecting your waypoints ..................................................... 25
2.9 Operating a networked E-Series Display ..................................................... 28
What does a networked system do? ........................................................ 28
Controlling a network ............................................................................. 28
Functions only affecting the display in use ............................................. 29
ESeries Reference Manual
2.10 Emergencies and warnings .......................................................................... 30
Man Overboard (MOB) .......................................................................... 30
Alarms .................................................................................................... 31
Chapter 3:
Working with Waypoints ..................................................................... 33
3.1 What is a waypoint? ..................................................................................... 33
3.2 How are waypoints represented? ................................................................. 34
3.3 Placing a waypoint ....................................................................................... 35
3.4 Navigating to a waypoint ............................................................................. 36
Start navigating to a waypoint ................................................................ 36
Stop navigating to a waypoint ................................................................ 37
3.5 Viewing waypoint information .................................................................... 37
3.6 Editing a waypoint ....................................................................................... 38
Changing waypoint details ..................................................................... 39
Moving a waypoint ................................................................................. 39
Erasing a waypoint(s) ............................................................................. 40
Changing the default symbol or group ................................................... 41
3.7 Sorting the waypoint list .............................................................................. 42
3.8 Organising waypoints into groups ............................................................... 42
Displaying the waypoint group list ......................................................... 42
Making a new waypoint group ............................................................... 43
Moving waypoints between groups ....................................................... 43
Renaming an existing group ................................................................... 44
Erasing a group ....................................................................................... 45
3.9 Controlling waypoint display ...................................................................... 45
Show/hide waypoint names ................................................................... 45
Showing/hiding waypoint symbols ........................................................ 46
Showing/hiding waypoint groups .......................................................... 46
Chapter 4:
Using the Chart...................................................................................... 47
4.1 Important ..................................................................................................... 47
Navionics support ................................................................................... 47
Safety ...................................................................................................... 47
Chart functionality ................................................................................. 47
Chart cards .............................................................................................. 48
ix
4.2 Uses of the chart application ........................................................................ 48
4.3 Viewing the chart ......................................................................................... 50
4.4 The chart display .......................................................................................... 50
4.5 Where am I on the chart? ............................................................................. 51
4.6 Moving around the chart .............................................................................. 51
4.7 Additional information on the chart ............................................................. 52
Displaying details of objects and features .............................................. 53
Finding nearby features and services ..................................................... 53
Animated tides and currents ................................................................... 54
Displaying details of tides ...................................................................... 57
Displaying details of currents ................................................................. 57
Displaying details of port services .......................................................... 58
Pilot book information ........................................................................... 60
Displaying panoramic photos ................................................................. 62
Displaying details of business services & points of interest ................... 63
Displaying an aerial photo overlay ......................................................... 64
Displaying vessel identity (AIS) ............................................................ 66
4.8 Measuring distances and bearings ............................................................... 67
... from your boat .................................................................................... 67
... between two points on your chart ....................................................... 67
4.9 Navigating to a specific point ...................................................................... 68
Go to an existing waypoint ..................................................................... 69
Resetting cross track error (XTE) ........................................................... 69
Arriving at your target waypoint ............................................................ 69
Stop navigating to your target waypoint ................................................. 70
Maintaining a view of your navigation ................................................... 70
4.10 Building and following a route .................................................................... 71
What is a route? ...................................................................................... 71
What can I do with a route? .................................................................... 71
Building a route ...................................................................................... 72
Following a route .................................................................................... 76
Resetting cross track error (XTE) ........................................................... 78
Viewing details of routes ........................................................................ 79
4.11 Editing routes ............................................................................................... 80
Selecting a route for editing .................................................................... 80
Editing the selected route ....................................................................... 81
ESeries Reference Manual
4.12 Monitoring where you are going .................................................................. 86
... using chart vectors .............................................................................. 86
... using the Course Deviation Indicator (CDI) ....................................... 87
4.13 Warnings of potential dangers ..................................................................... 87
4.14 Using the radar with the chart ...................................................................... 88
Synchronizing the chart with radar range ............................................... 88
Viewing MARPA targets on the chart .................................................... 88
Distinguishing between fixed and moving objects ................................ 89
4.15 Recording where you have been .................................................................. 90
What is a track? ...................................................................................... 90
How can I use tracks? ............................................................................. 91
Creating a track ....................................................................................... 91
Creating a route from a track .................................................................. 92
4.16 Editing tracks ............................................................................................... 93
Selecting a track for editing .................................................................... 93
Editing the selected track ........................................................................ 94
4.17 Defining how the chart windows are presented ........................................... 95
Working with multiple chart views ........................................................ 95
Setting the orientation of the chart ......................................................... 96
Setting the motion mode ......................................................................... 97
4.18 Altering the level of chart detail displayed .................................................. 98
Range rings ............................................................................................. 99
Navionics combined data cards .............................................................. 99
To display bathymetric information ....................................................... 99
Showing or hiding waypoints/waypoint information ............................ 99
Showing or hiding a route or a track ..................................................... 101
Showing or hiding cartographic features .............................................. 102
4.19 Setting up your chart and its cartography ................................................... 103
Chart Setup ........................................................................................... 103
Cartography Setup ................................................................................ 106
4.20 Chart layers ................................................................................................ 107
Radar overlay ....................................................................................... 108
Synchronizing chart scale with radar range .......................................... 108
Viewing MARPA targets on the chart .................................................. 109
AIS ....................................................................................................... 109
Range rings ............................................................................................110
xi
Chapter 5:
3D Chart................................................................................................ 111
5.1 Important ....................................................................................................111
3D Chart functionality ...........................................................................111
Safety .....................................................................................................111
5.2 An introduction ...........................................................................................111
5.3 What can I use the 3D Chart Application for? ............................................112
5.4 The 3D chart display ...................................................................................112
5.5 Where am I on the 3D chart? .......................................................................113
5.6 Moving around the 3D chart .......................................................................113
5.7 Other 3D controls ........................................................................................114
Soft keys ................................................................................................114
5.8 Changing the mode .....................................................................................115
Active motion mode ..............................................................................115
Planning mode .......................................................................................115
5.9 Changing the view ......................................................................................116
View options ..........................................................................................116
Multiple views .......................................................................................117
Vessel offset ...........................................................................................117
5.10 Aerial photo overlay ...................................................................................118
5.11 Making the view clearer ..............................................................................118
Exaggeration .........................................................................................118
Declutter ................................................................................................119
5.12 Using 2D and 3D charts together ............................................................... 120
3D view locator .................................................................................... 120
Chart synchronization .......................................................................... 121
ESeries Reference Manual
5.13 Using the 3D chart with a fishfinder .......................................................... 122
5.14 Navigating with 3D charts ......................................................................... 122
5.15 Setting up the 3D Chart .............................................................................. 123
Chapter 6:
The Fishfinder...................................................................................... 125
6.1 The fishfinder display ................................................................................ 125
6.2 Background information ........................................................................... 125
6.3 Operating the fishfinder ............................................................................. 126
6.4 Explaining the readout ............................................................................... 126
6.5 Factors influencing the readout ................................................................. 127
6.6 Display mode settings ................................................................................ 128
Adjusting the position of the zoomed area ........................................... 129
Bottom lock and bottom shift ............................................................... 130
Using A-Scope to view a live image ..................................................... 130
The A-SCOPE softkey ......................................................................... 130
Changing the range ............................................................................... 131
Range shift ............................................................................................ 132
6.7 Presentation toolbar ................................................................................... 132
6.8 Adjusting gain and power .......................................................................... 132
Auto gain settings ................................................................................. 132
Manually-set gain levels ....................................................................... 133
Power setting ........................................................................................ 134
6.9 Measuring depth and distance ................................................................... 134
Measuring depth and distance with VRM ............................................ 135
Adjusting the scroll mode and speed .................................................... 136
Pausing scroll ....................................................................................... 136
Viewing frequencies within a preset ..................................................... 137
Placing waypoints ................................................................................ 137
6.10 Fishfinder alarms ....................................................................................... 137
6.11 Editing presets ........................................................................................... 137
Manual frequency selection ................................................................. 138
Automatic frequency selection ............................................................. 138
6.12 Fishfinder configuration ............................................................................ 139
DSM and transducer setup ................................................................... 140
xiii
Chapter 7:
Using the Radar ................................................................................... 143
7.1 Introduction ............................................................................................... 143
7.2 What is radar? ............................................................................................ 143
Detecting targets ................................................................................... 143
Maximum radar range .......................................................................... 144
Factors impairing a radar picture .......................................................... 144
7.3 Powering on/off the various scanner operating modes .............................. 148
7.4 The radar picture ........................................................................................ 149
7.5 Marking a position on the radar screen ...................................................... 150
7.6 Changing what you see in the radar window ............................................. 150
Setting the orientation of the radar ........................................................ 150
Setting the motion mode ....................................................................... 152
Showing or hiding the range rings ........................................................ 154
Changing the bearing mode for EBLs .................................................. 154
7.7 Getting the best picture .............................................................................. 154
Using the GAIN functions .................................................................... 154
Using the enhance echoes functions ..................................................... 156
7.8 Changing the displayed range .................................................................... 159
Radar range and chart scale synchronization ....................................... 159
7.9 Measuring distances, ranges and bearings ................................................. 160
... Using the range rings ........................................................................ 160
... Using the cursor ................................................................................ 160
... Using VRMs and EBLs .................................................................... 161
... Using floating VRMs/EBLs ............................................................. 163
7.10 Using radar to avoid a collision .................................................................. 164
Guard Zones ......................................................................................... 164
MARPA ................................................................................................ 167
Setting up MARPA ............................................................................... 170
Acquiring a target to track .................................................................... 171
Cancelling targets ................................................................................. 171
Displaying vessel identity (AIS) .......................................................... 172
ESeries Reference Manual
7.11 Setting up your radar .................................................................................. 172
7.12 Warnings of potential dangers ................................................................... 174
Chapter 8:
Radar .................................................................................................... 175
8.1 Radar setup ................................................................................................ 175
Select scanner ....................................................................................... 175
Scanner setup ........................................................................................ 175
8.2 Radar alarms .............................................................................................. 177
8.3 Powering on/off the various scanner operating modes .............................. 177
8.4 Radar status ................................................................................................ 177
8.5 Radar range and image quality .................................................................. 177
Range .................................................................................................... 178
Image quality ........................................................................................ 179
Side lobes ............................................................................................. 179
Indirect echoes ...................................................................................... 180
Multiple echoes .................................................................................... 180
Blind sectors ......................................................................................... 180
Sea clutter ............................................................................................. 181
Rain or snow clutter .............................................................................. 181
Mutual radar interference ..................................................................... 181
8.6 Radar window overview ............................................................................ 182
Your position ........................................................................................ 182
Operation modes .................................................................................. 182
Other vessels or objects ........................................................................ 182
Factors affecting echo strength ............................................................. 183
8.7 Using waypoints with the radar ................................................................. 183
8.8 Radar display options ................................................................................ 183
Orientation ............................................................................................ 184
Heading-Up (H-UP) ............................................................................. 184
North-Up (N-UP) ................................................................................. 184
Course-Up (C-UP) ............................................................................... 185
Setting the motion mode ....................................................................... 185
Relative motion (RM) with optional vessel offset ................................ 186
True Motion (TM) ................................................................................ 186
Changing the bearing mode for EBLs .................................................. 187
xv
8.9 Dual range .................................................................................................. 187
8.10 Tuning the radar display: GAIN ................................................................ 187
Gain presets .......................................................................................... 187
Manually adjusting gain ....................................................................... 188
Rain clutter ........................................................................................... 188
Sea clutter ............................................................................................. 188
Super HD adjustments .......................................................................... 189
8.11 Tuning the radar display: ENHANCE ECHOES ...................................... 189
Interference rejection ........................................................................... 189
Expansion ............................................................................................. 190
Wakes ................................................................................................... 190
Scan to scan .......................................................................................... 190
8.12 Radar range ................................................................................................ 191
Synchronizing radar range and chart scale ........................................... 191
8.13 Measuring distance, range and bearing ...................................................... 192
Range rings ........................................................................................... 192
Bearing and range ................................................................................. 192
The Variable Range Marker (VRM) and Electronic Bearing Line (EBL) ..
193
Variable Range Marker ......................................................................... 193
Electronic Bearing Marker ................................................................... 194
Combined range and bearing ................................................................ 194
Tracking a target with a VRM or EBL .................................................. 194
Floating VRM and EBL ....................................................................... 195
8.14 Using radar to track objects ........................................................................ 196
Guard zones .......................................................................................... 196
MARPA ................................................................................................ 197
Displaying vessel identity (AIS) .......................................................... 201
Chapter 9:
Using the data application................................................................ 203
9.1 Introduction ............................................................................................... 203
9.2 Selecting a data application ....................................................................... 203
9.3 Selecting the data for display ..................................................................... 204
Pre-configured data panels ................................................................... 204
Customize the panels ............................................................................ 205
Chapter 10:
Autopilot Control................................................................................ 209
Emergency disengage .......................................................................... 209
ESeries Reference Manual
10.1 Enabling and engaging the autopilot ......................................................... 209
To enable autopilot control ................................................................... 209
To engage the autopilot in normal operation ........................................ 209
To engage the autopilot from the Setup Menu ...................................... 210
To disengage the autopilot in normal operation .................................... 210
Emergency disengage .......................................................................... 210
Autopilot Status Indicator .....................................................................211
10.2 The autopilot control screen .......................................................................211
10.3 Waypoint arrival ........................................................................................ 212
…when there are more waypoints in your route ................................... 212
…when you reach the last waypoint in your route ............................... 212
Chapter 11:
Video..................................................................................................... 215
11.1 Introduction ............................................................................................... 215
11.2 Setting up the video application ................................................................. 215
Displaying a video application ............................................................. 215
Customizing the video application ....................................................... 216
Adjusting the image .............................................................................. 219
Chapter 12:
Using the Course Deviation Indicator ............................................. 221
12.1 Introduction ............................................................................................... 221
12.2 The CDI screen .......................................................................................... 221
Steering instructions ............................................................................. 222
12.3 Selecting the CDI application .................................................................... 222
12.4 Modifying the CDI application .................................................................. 222
Chapter 13:
Using the Engine Monitor .................................................................. 223
13.1 Introduction ............................................................................................... 223
13.2 Displaying and setting up the engine monitor ............................................ 223
13.3 The engine monitor display ....................................................................... 225
13.4 Configuring the engine panels. .................................................................. 225
13.5 What should I do when an alarm is triggered? ........................................... 225
Chapter 14:
Weather (US only) ............................................................................... 227
14.1 Overview ................................................................................................... 227
14.2 Important information ............................................................................... 227
Disclaimer ............................................................................................ 227
xvii
14.3 Setting up the weather application ............................................................. 227
Pre-requisites for using the weather application .................................. 228
Adding a weather application ............................................................... 228
Specifying the weather elements .......................................................... 228
14.4 The weather display ................................................................................... 229
14.5 Moving around the weather map ............................................................... 229
14.6 Placing waypoints ...................................................................................... 229
14.7 Weather graphics ....................................................................................... 230
Precipitation (NOWRad) ..................................................................... 231
Storm Cast ............................................................................................ 231
Sea surface temperature (SST) ............................................................. 232
Canadian radar ...................................................................................... 232
Tracking storms .................................................................................... 232
Lightning .............................................................................................. 233
Surface observation stations ................................................................. 233
City forecasts ........................................................................................ 234
Wind ..................................................................................................... 235
Waves ................................................................................................... 235
Surface pressure ................................................................................... 236
Viewing data at a particular location .................................................... 236
14.8 Animated weather graphics ....................................................................... 236
Setting up animation ............................................................................. 236
Running animation ............................................................................... 237
14.9 Viewing weather reports ............................................................................ 237
Tropical statements .............................................................................. 237
Marine warnings ................................................................................... 238
Marine zone forecasts ........................................................................... 238
14.10Watchbox warnings ................................................................................... 239
Watchbox warning alerts ...................................................................... 239
Displaying marine watchboxes ............................................................ 240
Displaying watchbox data .................................................................... 240
14.11Weather application setup ......................................................................... 241
Selecting the Weather Setup Menu ....................................................... 241
Weather Setup options .......................................................................... 241
Showing/hiding marine watchboxes and zone boundaries .................. 241
ESeries Reference Manual
14.12Troubleshooting ........................................................................................ 242
Chapter 15:
Sirius Audio (US only)......................................................................... 243
15.1 To start using Sirius Radio ......................................................................... 243
15.2 Tuning to a channel .................................................................................... 244
15.3 Browsing channels ..................................................................................... 244
Filtering categories from the browse .................................................... 245
To filter categories ................................................................................ 245
15.4 Scanning channels ..................................................................................... 245
To scan channels ................................................................................... 245
15.5 Hiding or showing channels and categories ............................................... 245
To hide or show a channel or category .................................................. 245
15.6 Presets ........................................................................................................ 246
To assign a channel to a preset .............................................................. 246
To delete a channel from a preset .......................................................... 246
To move a channel to a new preset ....................................................... 246
15.7 Parental locking ......................................................................................... 246
To enable blocking ............................................................................... 247
To set up a password ............................................................................. 247
To change an existing password ........................................................... 247
To block a channel ................................................................................ 247
To enter a password .............................................................................. 248
15.8 Favourite song alerts .................................................................................. 248
To enable favourite alerts ..................................................................... 248
To set up a song or artist alert ................................................................ 248
Chapter 16:
Navtex .................................................................................................. 249
16.1 Overview ................................................................................................... 249
16.2 Setting up Navtex weather ......................................................................... 249
16.3 Incoming message alerts ............................................................................ 249
16.4 Viewing messages ..................................................................................... 250
Displaying the Navtex Message List .................................................... 250
Displaying and scrolling through a message ........................................ 250
16.5 Managing Navtex messages ...................................................................... 250
Selecting message alert categories ....................................................... 250
Sorting the message list ........................................................................ 251
xix
Chapter 17: Automatic Identification System (AIS) ........................................... 253
17.1 Introduction ............................................................................................... 253
17.2 What is AIS? .............................................................................................. 253
Classes of AIS data ............................................................................... 253
17.3 What do I need to run AIS? ........................................................................ 255
17.4 Selecting the AIS function ......................................................................... 255
AIS status ............................................................................................. 255
17.5 How is AIS data displayed? ....................................................................... 256
AIS Target symbols .............................................................................. 256
Viewing target information .................................................................. 257
17.6 Using AIS for collision avoidance ............................................................. 259
Safe zones ............................................................................................. 259
MARPA and AIS options ..................................................................... 260
Safety messages ................................................................................... 260
17.7 AIS Alarms ................................................................................................ 260
Local AIS alarms .................................................................................. 261
Active alarm list ................................................................................... 261
17.8 Simulator ................................................................................................... 262
17.9 AIS Layer Setup Menu .............................................................................. 262
Chapter 18: Maintenance & Troubleshooting...................................................... 263
18.1 Introduction ............................................................................................... 263
18.2 Maintenance procedures ............................................................................ 263
Servicing and Safety ............................................................................. 263
Routine checks ..................................................................................... 264
Cleaning the display ............................................................................. 264
18.3 Resetting the Display ................................................................................. 264
Settings reset ......................................................................................... 264
Settings and data reset .......................................................................... 265
18.4 Troubleshooting your Display ................................................................... 266
Common problems and how to solve them .......................................... 266
18.5 Getting Technical Support ......................................................................... 269
Help us to help you ............................................................................... 270
World wide web .................................................................................... 271
Contacting Raymarine in the US .......................................................... 271
Contacting Raymarine in Europe ......................................................... 272
ESeries Reference Manual
For Navionics cartography ................................................................... 272
For Sirius weather ................................................................................. 272
Chapter 19: System setup and customizing......................................................... 273
19.1 Changing the data master ........................................................................... 273
19.2 Customizing the page sets .......................................................................... 273
Graphical engine data ........................................................................... 273
Reconfiguring the application and page layout .................................... 275
Rename a page set ................................................................................ 275
Return to default setting ....................................................................... 276
19.3 Changing the databar ................................................................................. 277
Databar position ................................................................................... 277
Data bar size ......................................................................................... 277
19.4 Compass bar .............................................................................................. 278
Turning the compass bar on and off ...................................................... 279
Compass bar setup ................................................................................ 279
Customizing the contents of the data bar .............................................. 280
19.5 Changing the set up menu options ............................................................. 283
Application specific ............................................................................. 283
External equipment menus ................................................................... 283
System-wide menus ............................................................................. 283
Chapter 1: Overview
Chapter 1: Overview
This chapter gives an overview of the ESeries display system and its features.
1.1 What will my ESeries integrate with?
Autopilot
DVD
Instruments
Cameras
AIS receiver
23.47
DVD
Video
VIDEO
23.47
GPS
Radar scanner
E-Series display
M1500 or monitor
DSC VHF
PAGE
ACTIVE
WPTS
MOB
11.18.02
DATA
RAY240
MENU
OK
MENU
CH
16/9
HI/LO
WX
SCAN
WATCH
SQ
OUT
RANGE
IN
OK
CANCEL
Digital radar scanner
Remote keyboard
Personal Computer
Fishfinder
DSM 400 & 300
SeaTalkHS
switch
E-Series additional displays
Weather receiver
PAGE
ACTIVE
WPTS
MOB
DATA
MENU
OUT
RANGE
IN
CANCEL
D7514_3
OK
When used as part of a SeaTalk system it will display information from other SeaTalk
and NMEA instruments. It can also be networked with other ESeries displays by way
of Raymarine’s SeaTalk High Speed switch. Information from the ESeries display can
be transferred between applications and to other SeaTalk instruments within the
system. For more detail on system integration, please refer to the Installation Guide.
2
ESeries Networked Display Reference Manual
1.2 What can the ESeries Display do?
With the appropriate equipment connected to your system and the necessary data
available, your ESeries display combines the following applications which are used to:
Chart (Chapter 4)
Locate where you are.
0.5nm
North-Up
(Relative Motion)
Local
Interpret your surroundings.
Monitor where you are going.
Record where you have been.
Navigate to a specified position (waypoint).
Distinguish between fixed and moving objects.
Measure distances and bearings.
D7363_2
Build and navigate routes.
View details of nearby features & services.
View details of boats equipped with AIS.
You will need a chart card, and position/heading data, for the chart application to be
fully functional.
3D Chart (Chapter 5)
Display a 3D view of land, sea & features.
Locate where you are.
Draft
Navigate a route.
Synchronize with the 2D chart.
Identify fishing spots
D8702_1
Interpret your surroundings.
Monitor where you are going.
Go to an existing waypoint.
You will need a chart card and accurate heading and position data for your 3D chart
application to be fully functional.
Fishfinder (Chapter 6)
200kHz:
Auto
Range:
Build a picture of what is below your vessel.
Auto
Locate & distinguish underwater objects & targets.
Distinguish the seabed and its texture.
Obtain information about water depth, temperature.
Mark a point of interest, fishing spot etc.
ZOOM…
BOTTOM LOCK…
A-SCOPE…
PRESENTATION…
You will need position data, in addition to a DSM300, for your fishfinder to be fully
functional.
D7377-1
Determine depths and distances of targets.
TRANSDUCER
SETTINGS…
Chapter 1: Overview
Radar (Chapter 7) Digital Radar (Chapter 8)
6nm
North-Up
(Relative Motion)
Detect landmasses & navigation markers.
Rings 1nm
Detect and measure the range and distance of other
vessels.
Acquire targets and track them for collision avoidance.
Navigate to a specified position (waypoint).
TARGET
TRACKING...
GAIN...
TARGETS
DISPLAY...
D7375-2
View details of boats equipped with AIS.
VRM/EBL...
PRESENTATION...
You will need position and heading data, in addition to a compatible scanner, for your
radar application to be fully functional.
Data (Chapter 9)
D7376-1
View data generated by the system or by instruments
available on NMEA 0183, NMEA 2000 and SeaTalk or
SeaTalk2.
Video (Chapter 11)
View video images from on-board CCTV cameras, DVD or
video player.
D7378-1
Draft
Course Deviation Indicator (Chapter 12)
3nm
North-Up
Relative Motion
Local
View real-time display of your vessel on a 'rolling
road' in 3D perspective.
Give details of any correction required to steer your
vessel along a given course.
D7379-1
View data about the distance and time to go until
you reach a specified point.
You will need accurate heading and position data for your CDI application to be fully
functional.
4
ESeries Networked Display Reference Manual
Engine Monitor (Chapter 13)
D7497-1
View engine data e.g. engine temperature, oil pressure,
fuel level etc from up to three engines on a compatible
engine system.
Weather (Chapter 14)
Only available for the US.
Superimpose historical and forecasted weather graphics
on a world map.
View weather reports.
D8701-1
Determine conditions in your vicinity or at a particular
location.
You will need accurate position data and be connected to a Sirius weather receiver
(which is supplying the appropriate data) for your Weather application to be fully
functional.
Navtex (Chapter 16)
Major areas of NAVTEX coverage include the Mediterranean Sea, the North Sea,
coastal areas around Japan and areas around the North American continent.
Automatic broadcast of localised Maritime Safety
Information (MSI)
Receive navigational and meteorological warnings, and
search and rescue information.
D8728-1
Draft
You will need a Navtex receiver connected to your system via NMEA, in order to receive
this data.
Waypoints (Chapter 3) & AIS (Chapter 17)
Whilst not applications in their own right, waypoints and AIS are handled at system
level and are covered in separate chapters.
Chapter 1: Overview
1.3 The Simulator
The ESeries Display includes a simulator mode, which allows you to practice operating
your display without data from a GPS antenna, radar scanner. fishfinder or an AIS
receiver. The simulator mode is switched on/off in the System Setup Menu (see
page 228). Once enabled, you can use the simulator:
• Before installation  Simply connect the display to a 12V DC power supply,
fused at 1 amp by attaching the red core from the power lead to positive (+) and
the black core to negative ().
• After installation  Whilst in a marina or at anchor.
Please note that system settings made whilst in simulator mode, are not transmitted
via SeaTalk to other equipment.
Important: Incoming AIS safety messages cannot be displayed while the simulator is
switched on.
6
ESeries Networked Display Reference Manual
Chapter 2: General Operation
Chapter 2: General Operation
2.1
Introduction
This chapter gives details of the general operation of the ESeries display, and covers
the following subjects:
• Powering the display on/off.
• Using the controls.
• Application display.
• Displaying and editing additional information.
• Adjusting the display lighting.
• Initial setup procedures.
• Using CompactFlash cards.
• Managing data.
• Operating a networked ESeries Display.
• Emergencies and warnings.
2.2
Powering the display ON/OFF
Power ON
Press the POWER button until the introductory logo is displayed. The keys
light up and after a few seconds an application page and a navigation
warning and weather data disclaimer is displayed. Read this information
and then press OK to remove it.
At this time the radar scanner (if fitted and powered) is checked for compatibility with
the display. An error message is displayed if the scanner is incompatible.
D6577-1
Power OFF
Press and hold the POWER button until the power down count reaches
zero. If the POWER button is released within the countdown period, power
off is cancelled.
Remember to replace the suncover to protect the display.
8
ESeries Networked Display Reference Manual
2.3
Using the controls
The control panel
ACTIVE
When multiple windows are open:
- Press to select required window.
- Press and hold to maximise current
window.
- Press again to return to multiple
windows.
PAGE
Press to scroll through available
pages.
Press and hold to select different
page set or customise your own
layout.
PAGE
ACTIVE
WPTS
MOB
DATA
MENU
OUT
RANGE
IN
OK
Softkeys
Press to select the corresponding function identified
by the on-screen label
Power
Press once to turn ON.
Press again to access
backlight functions and
scanner controls.
Press and hold to turn the
display OFF.
CANCEL
WPTS/MOB
Press to display the waypoint
soft keys.
Press again to place waypoint at
your boat's position.
Press and hold to place a
Man Overboard (MOB)
marker at your current position.
Press and hold again to exit
MENU
Press to access the set up
menus.
Press and hold to access help
information.
Rotary control
Use to edit alpha-numeric
values, and scroll through lists.
Turn clockwise to increase
value and counter-clockwise to
decrease value.
Press to move the cursor to the
next character when editing
text.
Use to edit symbology (VRM/
EBL etc).
Trackpad
Used to control the on-screen
cursor and to scroll through
menu items.
Press the corresponding edge
of the trackpad to move the
cursor horizontally, vertically or
diagonally.
Press and hold to move rapidly
over larger distances.
RANGE
Press to change the display
scale so that a smaller or
larger area can be seen on
the screen.
CANCEL
Press to cancel the selected
on-screen option when editing
data; also used to return to
the previous soft key set or
menu.
Chart Card slot
Open the cover to install
CompactFlash cards.
OK
Press to select an on-screen
option, or return to the
previous soft key set or menu.
D7517_1
DATA
Press to access
ruler, chart vectors,
archive & transfer
and data bar
on/off functions.
Chapter 2: General Operation
Buttons and soft keys
To navigate to the required function you will need to press a series of buttons and/or
soft keys:
PAGE
Buttons
Access system functions or change what you see on-screen.
Within the text of this document they are written in bold capitals
e.g. WPTS/MOB.
Press and hold to access short cuts.
ACTIVE
WPTS
MOB
DATA
MENU
Soft keys
WAYPOINT AT
CURSOR
ERASE WAYPOINT
WAYPOINT AT
VESSEL
SORT LIST
WAYPOINT AT
LAT/LONG...
SET DEFAULT SYM
& GROUP...
SET UP DEFAULT
SYMB GROUP
GO TO WAYPOINT
OPTIONS…
WAYPOINT
GROUPS...
REVIEW AND EDIT
WAYPOINTS
VIEW AND EDIT
DETAILS…
EDIT DEFAULT
Example:
The example above shows the series of button and soft key presses
required to change the waypoint default symbol or group.
D7364-2
They change depending on
application or function
being performed.
Press the corresponding key
(below the screen) to select.
Further soft keys may be
displayed.
If a key has several options,
each press will highlight the
next option.
If a key displays a single
value or a slider above, use
the rotary control to adjust.
Within the text of this
document they are written
in capitals e.g. SORT LIST.
WPTS
MOB
REVIEW AND EDIT
WAYPOINTS ...
SET DEFAULT SYM
& GROUP...
SET UP DEFAULT
SYMB GROUP
Note: The key beep that you hear whenever a button or soft key is pressed, can be
switched off and the soft keys automatically hidden if required. For more details,
please refer to the Display Setup Menu on page 236.
D7365-2
This process of pressing buttons and soft keys to navigate to the required function is
simplified in this manual and represented by a strip e.g.
10
ESeries Networked Display Reference Manual
The cursor
When you are using the chart and radar applications, the cursor is used to move
around the screen:
WPT
D7369-2
D7368_2
D7366_3
The cursor appears on the screen as a white cross.
If the cursor has not been moved for a short period of time, it changes to
a circle with a cross in it, to make it easier to locate on the screen.
The cursor is contextsensitive  when it is placed over an object e.g. a
waypoint or chart feature, it changes color and a label or information
associated with the object is displayed. When you place the cursor over
certain items, the soft keys change to enable you to access related
operations.
Notes: (1) For a full list of cursor labels and their meanings, please see
Appendix C
(2) For details of how to temporarily hide the cursor, please see
page 236.
Displaying applications
The various applications that make up your ESeries system are displayed in a series of
screens known as page sets. There are 4 preconfigured and one empty page set to
choose from. Each page set contains 5 pages. These pages are made up of 1, 2, 3 or 4
windows combined in various formats. Each window can display an application e.g.
Page set
Video Weather
3D Chart
CDI
Fishfinder Data
Page
(consists of 1, 2, 3 or 4 windows
in various configurations)
Engine
Radar monitor
2D Chart
Window
If necessary, you can change the combination and layout of these page sets to meet
your particular needs (see page 221).
Note: For details of how to select page sets, pages and windows, please refer to
page 16.
D9025_1
2.4
Chapter 2: General Operation
11
2.5 Additional screen information
Information is displayed on the screen using a variety of methods:
Status
Statusbar
bar
Gives
Givesinformation
informationspecific
specifictoto
each
eachapplication.
application.
Cannot
Cannotbe
beedited
editedorormoved.
moved.
3nm
3nm
Head-Up
Head-Up
Data
Data bar
bar
Gives
Gives information
information associated
associated with
with
your
boat
or
the
environment.
your boat or the environment.
Customisable
Customisable content*
content*
Vertical
Vertical or
or horizontal
horizontal format*
format*
Display
Display or
or hide*.
hide*.
Normal
Normal or
or large
large size*.
size*.
Relative
Relative Motion
Motion
Statusicons
icons
Status
Confirm
status
of DSM,
DSM,
Confirm status of
GPS
and
scanner.
GPS, AIS and scanner.
Rings ½nm
½nm
Rings
Status bar
Gives information specific to
each application.
Cannot be edited or moved.
MARPA
ALARM
MARPA ALARM
D7456_1
Target
(onscreen)
screen)
Targetlost
lost (on
ACKNOWLEDGE
ACKNOWLEDGE
Pop-up messages
messages
Pop-up
Alert
you
Alert you to
to aa situation
situatione.g.
e.g.
alarm,
function
alarm, function not
notavailable.
available.
Not editable.
editable.
Not
May
require aa response
May require
responsee.g.
e.g.
press ACKNOWLEDGE to
press ACKNOWLEDGE to
silence alarms.
silence alarms.
Dialog
Dialogboxes
boxes
Enable
Enabledata
datatotobebeedited
editedoror
entered
into
store/list
entered into a store/liste.g.
editing
a waypoint.
e.g. editing
a waypoint.
Menus (see next page)
Menus (see next page)
Used to configure system to
Used to configure system
your particular needs.
to your particular needs.
* For details of how to adjust and edit the data bar, please see page 223
Note: To change the size of the text on screen, please see page 236.
D7456_2
Database
baselists
lists
Data
Containinformation
information you
Contain
you have
added
to
the
display's
memory
have added to the display's
e.g.
waypoints.
memory e.g. waypoints.
Highlight an
an entry
entry using
Highlight
with
trackpad or rotary control to
trackpad or rotary control to
display related information.
display related information.
Editable using soft keys.
Editable using soft keys.
12
ESeries Networked Display Reference Manual
Menus
MENU
MENU
D6582-1
Menus enable you to configure your system to your particular needs.
Whenever the MENU button is pressed, the Setup menu is displayed
containing a list of all the menus available for the active application
together with system wide menus e.g.
Setup
Menus for the active
application
External equipment/
instruments
GPS Status...
Compass Setup...
AIS Layer Status...
System-wide menus
System Setup...
Alarm Setup...
Display Setup...
Databar Set...
Select Page Setup...
System Diagnostics...
Remove CF Card
D7370_2
Radar Setup ...
For details of application menus, please refer to the appropriate chapter. For all other
settings, please refer to Chapter 15:System setup and customizing.
To access a menu:
1. Select the appropriate menu and setting:
Cartography Setup Menu
Setup
Chart Setup...
Cartography Setup...
GPS Status...
Compass Setup...
Detailed
On
On
ON
ON
1. Highlight item, using:
1. Highlight item, using:
Trackpad (up/down)
or
Rotary control
Trackpad (up/down)
or
Rotary control
2. Select item, using:
2. Select item, using:
Trackpad (right)
Trackpad (right)
D8500_1
MENU
Chart Display
Chart Grid
Chart Text
Chart Boundaries
Spot Soundings
2. To change the setting:
Cartography Setup Menu
Detailed
On
On
ON
ON
66ft
ALL
ON
Highlight or change value to
new setting, using:
Trackpad (up/down)
or
Rotary control
OK
OFF
7ft
10ft
16ft
20ft
33ft
66ft
D8501_1
Chart Display
Chart Grid
Chart Text
Chart Boundary
Spot Soundings
Safety Contour
Depth Contour
Nav. Marks
Chapter 2: General Operation
13
Editing the dialog box information
Dialog boxes enable data to be edited or entered into a list e.g. Edit Waypoint screen.
To edit/enter data into a dialog box:
1.
Select the field for editing:
e.g.
Symbol
Name
Waypoint 1
EDIT NAME
Group My Waypoints
Comment
2.
D8502-1
Highlight field to be edited
e.g. waypoint name
Edit/enter data and save:
e.g.
Symbol
Name
Wa
aypoint 1
OK
Group My Waypoints
Comment
3.
To move to next
character for
editing, use:
or
or
Turn
Press
D8503-1
To change
character or
selection, use:
Repeat Steps 1 and 2 if necessary.
Notes: (1) Character text can be entered in upper or lower case. (although the
system is not case sensitive e.g. WAYPOINT 1, Waypoint 1are considered to be the same name).
(2) If you need to use special or accented characters (e.g. ~ ` ´), the
Extended Character Set should be switched to ON in the System
Setup Menu (see page 228).
14
ESeries Networked Display Reference Manual
Status icons
The status icons on the data bar confirm whether the appropriate connections to your
ESeries system have been made:
Status icon
Description
D6892-3
The boat and fish icon indicates the current status of your fishfinder:
Icon animated  connection to a DSM has been successful.
Icon static  the DSM is connected but not transmitting.
Icon greyedout  no DSM is connected.
(animated icon)
D6893-2
The satellite icon indicates the current status of your GPS:
FIX  your unit is successfully connected to a GPS receiver.
NO FIX  your unit has been unable to connect to a suitable GPS receiver.
(static icon)
D6894-2
The scanner icon indicates the current status of your radar scanner:
Icon rotates  the scanner is transmitting (TRANSMIT/TX mode).
Icon static  the scanner is powered on but is not currently transmitting
(STANDBY mode).
Icon greyed out  this indicates that the scanner is currently powered
off (OFF mode).
Icon rotates and is then static  a power save mode in which the
scanner powers on/off intermittently (TIMED TRANSMIT mode).
(static icon)
The AIS icon indicates the current status of the AIS function:
AIS unit not available i.e. not connected or off.
AIS unit is switched on and operating.
D8929_1
AIS unit on with active alarms.
AIS unit switched on and operating but dangerous and lost alarm dis
abled.
Note: These icons will also appear when you are in simulator mode.
Chapter 2: General Operation
Initial setup procedures
When you first use your ESeries Display after it has been commissioned (see
Installation Guide), we recommend that you carry out the following:
• Selecting the data master (Networked ESeries Displays only).
• Set the language, the date and time format and preferred units of measurement.
• Select a page set.
• Select an application page/window.
• Adjust the display lighting.
Note: For full details of all System Setup options, please refer to Chapter 15:System set
up and customizing. For application specific set up options, please refer to the appro
priate chapter.
Selecting the data master (Networked ESeries only)
When a Networked ESeries system is powered on for the first time, an alarm will
sound and you will be asked to nominate which display is to be the data master. For
details of how to change the data master, please see page 28.
Setting the language, date/time format and units of mea
surement
To adjust the language, date/time format and units of measurement to your preferred
settings:
1. Select the setting:
Setup
System Setup Menu
Position Made Lat/Lon...
MENU
System Setup...
Alarm Setup...
Date/Time Setup...
Units Setup...
Highlight
System Setup
System Integration Setup...
Waypoint Password Setup...
Highlight required
setting
Enter System
Setup
D8504-1
Enter setting
2. Adjust the setting:
e.g.
Date/Time Setup Menu
Date Format
Time Format
Local Time Offset
or
mm/dd/yy
12hr
UTC
mm/dd/yy
dd/mm/yy
OK
Change value as
required
3. Repeat this process until you have changed all of these settings.
D8505-1
2.6
15
16
ESeries Networked Display Reference Manual
Selecting a page set
Your Display has four preconfigured page sets and one empty set for you to choose
from. The applications configured in a page set is a local setting and will therefore only
affect the individual display on which you are working.
PAGE
OK
Highlight appropriate pre-configured page set
D8511-1
Press &
hold
Note: Alternatively, you can access the Select Page Set screen via MENU.
If none of the preconfigured page sets meet your particular requirements and/or you
intend to use the engine monitor, weather or video application, refer to the Setup and
Customizing chapter for details of how to customize both the layout and the
application appearing in each window.
Selecting an application page
Once you have selected the appropriate page set (see previous section), choose the
application page that you wish to use:
PAGE
Press until required
page displayed
Or:
Press soft key of
required page
D8512-1
PAGE
Chapter 2: General Operation
17
Selecting an application window
When the selected page has more than one window, the window that is currently
active will be bordered in red e.g.
Soft keys
associated with
active window
D8516_1
Active window
highlighted
Changing the active window
To change the active highlight to other windows on the page and display the
associated soft keys:
e.g.
Active
window
Active
window
ACTIVE
D8513-1
Press to move
active window
Multiple to single window
To make the active window fullscreen when multiple windows are being displayed:
Multiple windows
Press and
hold
Single window
D8514-1
ACTIVE
Single to multiple windows
To return to multiple windows:
Single window
Multiple windows
D8515_1
ACTIVE
18
ESeries Networked Display Reference Manual
Adjusting the display lighting
The display has two distinct color palettes, for day and night operation. You can also
manually adjust the backlight level.
Note: The display lighting is a local setting and will therefore only affect the individual
display on which you are working.
Day/night operation
To select the day/night mode of operation:
PALETTE
DAY
NIGHT
D6802-3
OK
Toggle as required
The display saves the current palette when the unit is powered off. If the palette was set
to NIGHT when it was last used, and you then power on in bright sunlight, it may be
difficult to see the screen. Reset the palette to DAY to return to normal daytime
lighting.
Backlight level
To adjust the backlight level when in day or night operation mode:
Backlight Level
Change the level as required
D8517_1
OK
Note: The backlight level application will autohide once button activity ceases for peri
ods greater than 3 seconds
Chapter 2: General Operation
19
2.7 Using CompactFlash cards
Cautions
CAUTION: CompactFlash Card Installation
When installing CompactFlash cards ensure that the card is fitted the correct
way around. DO NOT try to force the card into position as this may result in
irreparable damage to the card.
CAUTION: Water Ingress
To prevent the ingress of water and consequent damage to the display,
ensure that the chart card door is firmly closed at all times. This can be
confirmed by an audible click.
CAUTION: Card Removal
DO NOT use a metallic instrument such as a screwdriver or pliers to help you
remove a card, as doing this can cause irreparable damage.
CAUTION: Card writing
CompactFlash cards can be damaged if they are removed from the unit
during either a read or write operation. A warning is displayed during write
operations. The unit is continually reading the card. It is therefore essential
that before removing the card you follow the correct procedure to stop
access to the card.
What are CompactFlash cards used for?
CompactFlash cards enable you to get the most from your display. Their uses include:
• Detailed cartographic information
Obtain detailed cartographic information of the area that you navigate using Nav
ionics® chart cards. To check the current availability of Navionics chart card types,
please visit www.navionics.com or www.navionics.it.
The amount of cartographic detail shown varies for different areas and for differ
ent scales. The chart scale in use is indicated in the status bar  the number repre
sents the distance in nautical miles from the top of the chart window to the
bottom of the chart window.
• Archiving
To archive waypoints, routes and tracks.
• Saving
To save waypoint, route and track data for use by other equipment e.g. a PC.
You can remove and insert cards while a chart is displayed provided that you follow the
correct procedure (see page 20). The chart information is retained onscreen until the
chartplotter redraws the screen; for example, when you pan outside the current area,
or use the RANGE button to change the chart scale.
Note: In a networked system, cartographic data is available to any ESeries display
connected on the SeaTalk High Speed network. However, the ARCHIVE and TRANSFER
functions only operate with the card inserted in the display at which you are working.
20
ESeries Networked Display Reference Manual
Inserting a card
To insert a card, refer to the illustration and:
1. Check that you are using the correct type of card (see Important Information, at the
beginning of this manual).
2. Open the chart card door, located on the front left of the display.
3. Insert the card as shown, with the lip of the card facing inwards. It should position
easily. If it does not, DO NOT force it, check the direction in which the lip is facing.
4. Gently press the card home.
5. To prevent the ingress of water and consequent damage, close the chart card door
and press firmly until a click is heard.
Narrow
Groove
D7215_2
Lip
Removing a card
...with the unit powered on
1. Select the CF Card Removal function:
System Diagnostics...
Remove CF Card
CF Card Removal
You may now safely remove your
compact flash card.
Press OK or CANCEL when finished.
Highlight
Remove CF Card
Select Remove
CF Card
IMPORTANT:
If you try to remove a card without accessing the setup menu, a blue screen and
warning message is displayed and the unit must be restarted. In an Eseries net
worked system, where any display may be accessing the card, this message
D8518-1
Setup
MENU
Chapter 2: General Operation
2.
3.
4.
5.
21
appears on all displays in the network. All displays will therefore need to be
restarted individually.
You must only remove the card while the CF Card Removal message is displayed.
Once the message is closed, the card should no longer be removed.
Open the chart card door.
Grip the card and pull to remove it from its slot.
To prevent the ingress of water and consequent damage, close the chart card door
and press firmly until a click is heard.
Press OK.
...with the unit powered down
1. Open the chart card door.
2. Grip the card and pull to remove it from its slot.
3. To prevent the ingress of water and consequent damage, close the chart card door
and press firmly until a click is heard.
2.8
Managing data
This section explains how you can manage the data contained in your ESeries and
includes the following:
• Writing/retrieving to a CF card.
• Erasing information from a card.
• Erasing information from your system.
• Transferring information to/from a PC.
• Password protection.
Writing/retrieving data to a CompactFlash card
Your display can save up to 1,200 waypoints, 150 routes and 10 tracks in data base
lists. Once this number is reached you will need to archive data to a CompactFlash card
for safekeeping or retrieval at a later date. Alternatively, you can transfer data to
another instrument or PC using SeaTalkhs or NMEA. When navigation is active, you can
also receive waypoints, routes and tracks from a PC, other SeaTalkhs, SeaTalk and
NMEA instruments (see page 25).
Note: In a networked ESeries system, you archive to and retrieve data from the Com
pactFlash card in the display on which you are working.
22
ESeries Networked Display Reference Manual
Saving information to a card
Important:
Raymarine strongly recommend that you save data to a separate CompactFlash card
and not to a Navionics card containing cartography.
1. Insert card and select the SAVE TO CARD function:
ARCHIVE AND
TRANSFER
SAVE TO CARD
D8070_1
DATA
Insert card
2. Select list containing data for saving:
e.g.
ROUTE LIST
Toggle to required
list
Contents for selected list displayed
D8655_1
Route 1
Route 2
Route 3
SELECT LIST
WPT RTE TRK
3. Define data for saving
To save all items in list to card:
SAVE ALL
Save Route
Or
To save individual items:
e.g.
e.g.
ROUTE LIST
SAVE ROUTE
Follow on-screen instructions
to remove card
Highlight item
for saving
D8520_1
Route 1
Route 2
Route 3
Chapter 2: General Operation
23
Retrieving information from a card
1. Insert card and select the RETRIEVE FROM CARD function:
RETRIEVE FROM
CARD
ARCHIVE AND
TRANSFER
D9094_1
DATA
Insert card
2. Select required list:
e.g.
ROUTE LIST
Toggle to required
list
Contents for selected list displayed
D8655_1
Route 1
Route 2
Route 3
SELECT LIST
WPT RTE TRK
3. Define data to be retrieved:
To retrieve all selected database items:
RETRIEVE ALL
Retrieve Route
Or
To retrieve individual items:
e.g.
ROUTE LIST
Follow on-screen instructions
RETRIEVE ROUTE
Highlight item for
retrieving
If whilst retrieving information a selection is already found to exist on the system, a
warning message will appear.
The soft keys will change to give you the options of retrieving as new, replacing or
cancelling the retrieving process
D8656_1
Route 1
Route 2
Route 3
24
ESeries Networked Display Reference Manual
Erasing information from a card
If you wish to remove information from a card, for example you no longer need it, or
the card is full, it can be erased by using the ERASE FROM CARD soft keys. A message
will be displayed on screen asking you to confirm that you want to delete the item(s),
before it takes place.
1. Insert the card and select the ERASE FROM CARD function:
ERASE FROM
CARD
ARCHIVE AND
TRANSFER
D8168_1
DATA
Insert card
2. Select the required list:
e.g.
ROUTE LIST
Toggle to required
list
Contents for selected list displayed
D8655_1
Route 1
Route 2
Route 3
SELECT LIST
WPT RTE TRK
3. Define data to be deleted:
To delete all items:
ERASE ALL
YES
Or
To delete individual items:
e.g.
ROUTE LIST
ERASE ROUTE
Highlight item for
deleting
D8657_1
Route 1
Route 2
Route 3
Chapter 2: General Operation
25
Sending and receiving information using a PC
ARCHIVE AND
TRANSFER
DATA
TRANSFER ON
NMEA...
D8638_1
You can transfer and retrieve waypoints or routes to and from another instrument or
PC using NMEA or SeaTalkhs.
With a RayTech 6.0’s planner you can transfer waypoints and routes via a CF memory
card. Such transfers require that the PC be connected to the display’s NMEA port via a
serial data cable. RayTech 6.0 will transfer waypoints and routes via SeaTalkhs.
To transfer or receive information:
1. Select the transfer on NMEA option:
SEND WPTS ON
NMEA
SEND RTES ON
NMEA
RECEIVE ON NMEA
STOP TRANSFER
D6808-2
2. Press the appropriate soft key to send or receive NMEA:
STOP TRANSFER.
3. When transfer is complete, STOP TRANSFER greys out and the soft keys reappear.
Note: If you wish to stop the transfer at any point, press
Password protecting your waypoints
If required, you can prevent access to, modification and sight of your waypoint and
route databases and functions by means of a password.
Password confirmation
When Password Protection is enabled and you are attempting to access a password
protected function for the first time during a powercycle, the system will request
confirmation of your password before you can:
• Access WPTS key functions. This does not affect the operation of the MOB function.
• Access ROUTES soft key functions.
• Create a route from a track. All other track functions are unaffected.
• Archive or transfer any waypoints.
• Enter the Waypoint Password Setup menu.
Note: Once you have provided a password to the system, it must be entered to access
the Password Setup submenu, regardless of the whether Password Protection is set to
ON or OFF.
Disabled data/functions
When Password Protection is ON and you have not entered a password you will be
unable to:
26
ESeries Networked Display Reference Manual
• View details of waypoint and route databases.
• Edit waypoints or routes.
• Goto an existing waypoint.
• Follow a route.
• View waypoints on screen (even when the SHOW/HIDE status is set to SHOW).
• View waypoint names on screen (even when WAYPOINT NAME is set to ON).
All other options including GOTO CURSOR are unaffected.
Setting up a password
To setup a password:
1. Select Waypoint Password Setup:
Setup
System Setup Menu
Radar Setup...
GPS Status...
Compass Setup...
System Integration
Waypoint Password Setup
System Setup...
Highlight Waypoint
Password Setup
Select Waypoint
Password Setup
Highlight required
System Setup Menu
Select System Setup
Menu
D8954_1
MENU
2. Change the Enable Password status to ON, read and accept the warning:
Setting Password Protection
required a password to access
your waypoint and route
databases.
If you forget your password you
will lose your waypoints and
routes
Raymarine recommends that you
archive your waypoints and
routes
Waypoint Password Setup
OK
ON
Select Enable
Password
YES
Read and accept
the warning
Select ON.
D8962_1
Enable Password
Change Password...
3. Enter a password and confirm it:
e.g.
e.g.
Edit Password
Password: Carrot
Confirm Password:
Hint:
OK
Choose a word that will help you
to remember your password
Enter a password
(1-16 characters)
Password: Carrot
Confirm Password: Carrot
Hint:
OK
Choose a word that will help you
to remember your password
and/or:
Repeat to confirm
the password
D8957_1
and/or:
Edit Password
Note: The password is case sensitive.
Chapter 2: General Operation
27
4. Add a hint, to help you to remember your password (optional):
Your password has been accepted.
If you continue your waypoints
and routes will be protected.
Edit Password
Password: Carrot
If you forget your password you
will lose your waypoints and
routes
Raymarine recommends that you
archive your waypoints and routes
Do you want to continue?
OK
Confirm Password: Carrot
Hint: Rabbit
Choose a word that will help you
to remember your password
and/or:
YES
Add a hint word
(0-16 characters)
Read and accept the warning
D8958_1
e.g.
The password is now set and protection enabled although access to the waypoint and
route functions remains available until you restart your system.
Note: If required, this password can be changed by selecting the Change Password
option on the Waypoint Password Setup Menu.
Enabling/disabling password protection
Once you have set up a password on your system (see previous section) you will need
to key in this password whenever you want to change the status of the password
protection feature.
To enable/disable password protection:
1. Select Waypoint Password Setup:
Setup
Radar Setup...
MENU
GPS Status...
Compass Setup...
System Setup Menu
System Integration
Waypoint Password Setup
System Setup...
Select System Setup
Menu
Highlight Waypoint
Password Setup
Select Waypoint
Password Setup.
D8960_1
Highlight required
System Setup Menu
2. Enter your password ensuring that the appropriate upper or lower case characters
are used and then enable/disable the password protection, as required.
Enter Password
Password:
Carrot
Waypoint Password Setup
OK
Enable Password
Change Password...
OFF
OK
Enter password
Select OFF
D8961_1
Select Enable Password
Important: If you enter an invalid password more than twice within one power cycle
the system shall display the hint. There is no limit to the number of attempts to enter a
valid password but if you forget your password, you will need to perform a Settings
28
ESeries Networked Display Reference Manual
and Data Reset (see page 229) which will erase all waypoints in the unit’s memory.
Raymarine strongly recommend therefore that you regularly backup your waypoints,
routes and tracks to a CF memory card.
2.9 Operating a networked ESeries Display
What does a networked system do?
If you have connected two or more ESeries Displays (via either a crossover coupler or
SeaTalk High Speed Network Switch), data is transferred across the network enabling
you to input, view and maintain applications and data across all your Displays
irrespective of the Display from which the data originated (excepting Video Input).
To ensure that the latest data i.e. SeaTalk data and waypoints, routes and tracks
databases is available at all displays, the system needs one display to be designated as
the data master.
Controlling a network
System data including usercreated databases are managed by the data master. The
display that has been installed and nominated as the master, should always be
switched on (preferably first). The master display will copy its database to all other
Displays that are switched on, each time it detects a change.
If the system does not detect a master, either because it is not switched on or because
a master has not been selected, an alarm will sound and you will be prompted to select
a master display.
Note: The data master copies its database to all other displays in the system. To pre
vent loss of data when adding displays, or changing the master, ensure that you select
the appropriate display as the master. You can archive the database onto a Compact
Flash card and retrieve it later.
Changing the master display
On the display that you wish to nominate as the master:
1. Display the System Setup menu:
Setup
MENU
Radar Setup...
GPS Status...
Compass Setup...
System Setup...
Enter System Setup
2. Select the System Integration then Data Master option:
D8652_1
Highlight System Setup
Chapter 2: General Operation
29
System Setup Menu
Lat/Long
ON
ON
Position
Auto (01 E)
00 E
English (US)
OFF
ON
Enabled
ON
OFF
Date/Time Setup......
Units Setup.....
System
integration.....
Highlight System
Integration
System Integration Setup Menu
DSC Message
Seatalk Alarms
Data Master
Brigdge NMEA Headings
ON
Highlight Data Master
Enter Data Master
Enter System Integration
D8653_1
Postion Mode
TD Setup
Simulator
Bearing Mode
MOB Data Type
Variation Source
Manual Variation
Langauge
Extended Charactor set
Ground Trip Reset.....
Settings Reset......
Settings and Data Reset.....
Any such changes that you make to the nominated master will be saved when you
power off.
Functions only affecting the display in use
The majority of functions, settings, additions and changes that you perform on a single
Display are ‘seen’ by all other Displays connected to your network. There are however
some local settings that will only affect the individual display on which you are
working.
These local settings are summarized as follows:
• Page set  selecting a set, name and applications configuration.
• Power on/off key (including Day/night setting).
• The ACTIVE window.
• The displayed panel in the digital data or engine monitoring application.
• Radar and Fishfinder presentation settings.
• Radar VRMs, EBLs and Wakes.
• Chart presentation settings when the Chart View is set to LOCAL.
• Show/hide waypoints, routes or tracks.
• Fishfinder Setup Menu options (top half of menu only).
• Video, Databar and Display Setup Menus.
• Databar on/off and configuration.
• Ruler settings.
30
Emergencies and warnings
You can use your ESeries display to mark the position of a man overboard or to sound
an alarm when a particular situation occurs e.g when a depth limit is reached, a
specified period of time has elapsed etc.
Man Overboard (MOB)
Marking a MOB
WPTS
MOB
Press and hold
until alarm sounds
D6652-3
2.10
ESeries Networked Display Reference Manual
If you lose a person or object overboard, and need to return to the location, you should
use the Man Overboard (MOB) function immediately. The MOB function can be used
whilst any application is in use and is activated by either pressing and holding the
WPTS/MOB key for three seconds, or by a MOB message being received from other
equipment on the SeaTalk system.
When a MOB is activated the following is initiated automatically:
• Alarm  the MOB alarm is triggered (Morse  every 30 seconds)
• Waypoint  a MOB waypoint is placed at your current position.
• Positional information  the bearing, range and vessel position are displayed in
the data bar. These are calculated according to the MOB data type set in the System
SetUp (see page 228). Assuming that your boat and the MOB are subject to the
same tide and wind effects, dead reckoning normally gives a more accurate course.
• Radar range change  if radar is transmitting, the system changes the radar
range to 1/8 nm.
• Active navigation is suspended  Navigation to any active waypoint is sus
pended and any existing navigation function is cancelled. No further GOTO or route
functions are selectable whilst the MOB function is active.
• Autorange motion mode  If radar/chart synchronisation is set to OFF (see
page 84), the chart application changes the motion mode to Autorange. This dis
plays the largest possible scale of chart that will include both the target waypoint
(MOB symbol) and your onscreen vessel.
• Other equipment  other Raymarine equipment acknowledges the MOB.
• Current position to MOB position  as your vessel moves away from the MOB
position, a dotted line is displayed from your current position to the MOB position.
Note: To obtain a MOB position, you need either position data from a GPS (or equiva
lent device) or heading and speed data.
D9101_1
Chapter 2: General Operation
31
Silencing a MOB
To temporarily silence the alarm from a MOB, press any key on any instrument on the
SeaTalk system. After approximately 10 seconds the alarm will sound once more if the
state of MOB is still active.
Silencing an alarm will not deactivate or clear the MOB state.
Clearing a MOB
To clear a MOB and its data:
Press and hold
for 4 seconds
D8231_1
WPTS
MOB
Once cleared, your chart and radar
applications will return to the motion
mode that applied prior to the MOB
alarm and the GOTO and route functions
will once more be available.
Note: Alternately if you have a MOB key
pad fitted, press and hold the MOB key.
Alarms
You get warning of a hazard or a particular situation via inbuilt alarms which are
generated for the system as a whole or for individual applications. When an alarm
sounds, a message box is displayed explaining the cause of the alarm.
You can specify what alarms will operate and the parameters within which they will
sound, via the Alarm Setup Menu (see page 232).
Cancelling alarms
Display alarms
By pressing the ACKNOWLEDGE soft key, the alarm is silenced and any message box is
cleared. If the alarm has been generated by the chartplotter, the appropriate action is
taken. For example, following an arrival alarm, the next route leg is activated.
Please note:
• Although you can change the configuration of the arrival alarm, it cannot be turned
off.
• To cancel a MOB alarm, press and hold the WPTS/MOB until the MOB symbol dis
appears from the screen.
• If an anchor alarm is silenced, but the alarm condition persists, the alarm is
repeated every 30 seconds
External alarms
If an instrument that is connected to the display on SeaTalk generates alarms, these
will sound on your ESeries display accompanied by a popup message box. You can
cancel these alarms by pressing the ACKNOWLEDGE soft key. The alarm will be
silenced, but no other action will be taken by the ESeries display.
32
ESeries Networked Display Reference Manual
Chapter 3: Working with Waypoints
33
Chapter 3: Working with Waypoints
This chapter gives details of how to place, edit, manage and navigate to a waypoint.
What is a waypoint?
A waypoint is a position marked on a chart, radar or fishfinder window to indicate a
site (for fishing, diving etc.) or as a place to navigate to. By default, all waypoints are
indicated on screen by a waypoint symbol  x. This symbol can however be changed if
you wish. You can also select an alternative symbol to be used as the default for newly
created waypoints.
Waypoint symbols
D8696_1
3.1
Note: For details of how to change the symbol, please refer to page 39.
Waypoints are a core feature of the Eseries display. They can be created in any
application and are displayed on the radar, chart and fishfinder windows. A series of
waypoints can be combined together to form a route. If you have networked several E
Series Displays, any waypoints that are created on one display are ‘seen’ by all the
other displays.
The details of all waypoints, irrespective of the application they were created in, are
stored in a dedicated waypoint list which will hold up to 1200 waypoints. All waypoints
are by default, placed in the MY WAYPOINTS group. If required, you can create new
groups and change the default group. If necessary, waypoints can be archived to a
CompactFlash card or transferred to another NMEA compatible instrument. If the
system receives an active waypoint over SeaTalk or NMEA, it is displayed but cannot be
edited.
If required, you can prevent access to, modification and sight of your waypoint and
route databases and functions by means of a password. For more information see
page 25.
Note: You can only archive and transfer waypoints to a CompactFlash card/NMEA link
installed at the display on which you are working.
34
How are waypoints represented?
Waypoints on 2D Chart and Radar windows
On 2D chart and radar windows, a waypoint is represented when it is both active
(displayed in a box) and inactive (no box) i.e.
Default waypoint
Active waypoint
Alternative symbol
D8694_1
Waypoint 1
Waypoints on 3D Chart and CDI windows
D8698_1
On 3D chart and CDI windows, a waypoint is represented only when it is active
(displayed in a box).
Waypoints on Fishfinder windows
When a waypoint is created it is represented on fishfinder windows, by a vertical line
labelled WPT. This symbology cannot be changed.
WPT
WPT
WPT
D8697_1
3.2
ESeries Networked Display Reference Manual
Note: A waypoint can be placed when a Weather application window is active but it
will not be seen in the weather window.
Chapter 3: Working with Waypoints
Placing a waypoint
A waypoint can be placed at:
• The cursor position.
• Your vessel’s position.
• At a position of your choosing (using lat/lon or Loran TD coordinates between 80
N/S).
When you are placing a waypoint, you can either accept the default or customize its
details. For more information see page 38.
Once a waypoint has been placed, you can view its details and edit them (if necessary).
For more information, see page 37 and page 38.
... at the cursor
OK
WAYPOINT AT
CURSOR
Or
Wait 4 secs
Move cursor to
required position
for waypoint
Accepts default
D7457-2
WPTS
MOB
... at your vessel’s position
WAYPOINT AT
VESSEL
OK
Or
WPTS
MOB
Or
Wait 4 secs
x2
D7458_2
WPTS
MOB
Accepts default
If the system cannot determine your position, a warning is displayed and the waypoint
is not placed.
... at a known position
WPTS
MOB
WAYPOINT AT
LAT/LON...
Place Waypoint
Position:
50 50'.838N
01o06'.331W
Enter position
OK
x2
D7459_2
3.3
35
36
Navigating to a waypoint
This section explains how to start and stop navigating to a waypoint. When you
navigate to a waypoint or to the cursor position, the data is sent on NMEA 0183 and
SeaTalk and can be used by an autopilot, if connected. For more information on
navigation, see page 64.
Start navigating to a waypoint
D8285_1
You can navigate to a waypoint using the cursor, via the
WPTS MOB button or by selecting the GOTO option.
Once navigation is active, the waypoint symbol is
surrounded by a box and a dashed line appears between
your boat and the waypoint.
If required you can display navigation details for the
active waypoint in the data bar (see page 224).
...using the cursor
To navigate to a waypoint using the cursor, when a chart or radar application is active:
GO TO WAYPOINT
WPT
D7461_4
Position cursor over
waypoint to go to.
...via the WPTS MOB button
To navigate to a waypoint using the WPTS/MOB button when any application is active:
GOTO WAYPOINT
OPTIONS ...
Waypoint List
GOTO WAYPOINT
D6559-3
WPTS/
MOB
Select required waypoint
.... by selecting the GOTO option
You can navigate to a waypoint using the GOTO option when a 2D or 3D chart
application is active and the top level chart soft keys are displayed:
GOTO WAYPOINT
OPTIONS...
GO TO ...
Waypoint List
Or
GOTO CURSOR
GOTO WAYPOINT
Select required waypoint
D7503_2
3.4
ESeries Networked Display Reference Manual
Chapter 3: Working with Waypoints
37
Stop navigating to a waypoint
If at any time you wish to stop navigating towards the selected waypoint:
WPTS/
MOB
GOTO WAYPOINT GOTO WAYPOINT
WPTS/
STOP GOTO
OPTIONS...
MOB OPTIONS...
STOP GOTO
Or
Or:
WPT
WPT
Position cursor over
active waypoint.
D7505-2
Position cursor over
active waypoint.
STOP GOTO
D7505-1
STOP GOTO
Once navigation is no longer active, the waypoint symbol returns to its normal
unboxed state and the dashed line between your boat and the waypoint is removed.
Viewing waypoint information
You can view the details of any waypoint that you have placed, by either selecting it
with the cursor (in radar and chart windows) or by selecting it on the waypoint list.
Once you are viewing a waypoint’s details, a variety of editing and managing options
are available.
You can also display navigation details for the active waypoint in the data bar (see
page 224).
...using the cursor
To view the details of a waypoint that is not active.
Edit Waypoint
OK
EDIT WAYPOINT
WPT
Waypoint details displayed
Position cursor
over waypoint
To exit waypoint list
D7506_2
3.5
Note: Details of the waypoint that you are currently navigating to, can be accessed via
the waypoint list as described below.
...using the waypoint list
The waypoint list shows all the waypoints that have been placed (including the active
one), and displays details of the selected waypoint:
Note: Temperature and depth are only captured (if available) for waypoints placed at
your vessel’s position.
ESeries Networked Display Reference Manual
D6560-2
38
To access the waypoint list:
REVIEW AND EDIT
WAYPOINTS...
Waypoint List
OK
To exit waypoint list
Select required waypoint
Editing a waypoint
D6561-2
Once a waypoint has been placed it can be edited in a variety of ways. You can:
• Change the waypoint details  name, symbol, group or add a comment.
• Move a waypoint.
• Erase a waypoint.
• Change the default symbol and group of newly placed waypoints.
D6561-1
3.6
D7507-2
WPTS/
MOB

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 60
Producer                        : AFPL Ghostscript 8.14
Create Date                     : 2007:09:24 15:38:14
Modify Date                     : 2007:09:24 15:38:14
Title                           : E-Series Networked Display Ref Manual Part 1.pdf
Creator                         : PDFCreator Version 0.8.0
Author                          : vina.kerai
Subject                         : 
EXIF Metadata provided by EXIF.tools
FCC ID Filing: PJ5-DP4KW

Navigation menu