Kondo Kagaku T39EX2 Radio control transmitter User Manual EX 2 manual En 0530

Kondo Kagaku Co., Ltd. Radio control transmitter EX 2 manual En 0530

Contents

06_1_Users_Manual_rev1

INSTRUCTION MANUALKONDO KAGAKU Co., Ltd. 2015 Ver.1.0
2Title TitlePage Page■ Table of Contents ※ Click the page number to jump to that page.■ Table of Contents 2■ For Safe Operation 3■ Getting Started 5●Transmitter Assembly 5●Transmitter Dismantling 5■ Names of Parts 6●ET Keys (1-5) and BT Button (1) 7●Steering Adjustment 7●Wheel Cap Removal 7●Throttle Adjustment 7●Throttle Position Adjustment 7●Colored Grip and Pad Replacement 7●Unit Connector 8●Power Switch 8■ Preparations 9●Battery Installation 9●Battery Level Warning 9● Initializing EX-2 10●How to change the Modulation 10●Countermeasures Against Noise 11●Receiver Installation 12●Pairing (For general receiver) 13●Pairing (For MHS Mini-Z) 14●Fail-Safe Setting 15■ Procedures Prior to Operation 16●Trim and Sub Trim Operation 17■ Operating procedure 18●STEERING 18●THROTTLE 19●3CH 4CH operation 20■ Display and Control Method for attaching the Xpansion unit 21●Basic Operations to Change Settings 21●How to attach Xpansion unit 22●Startup Screen and Initial Screen 23●VR information setting 24●How to change the Modulation mode 24●Pairing (For general receiver) 25●Pairing (For MHS Mini-Z) 26■TOP MENU 27■□□ FUNCTION 29● Model Menu (Model) 29▶Model Select (MDL-Select) 29▶Model Name (MDL-Name) 29▶Model Copy (MDL-Copy) 30▶Model Reset (MDL-Reset) 30● TIMER　MENU 31▶TRGSTART (Trigger Start) 31▶LAP HISTORY (Lap History) 31▶ALARM (Alarm) 31●KEYSET (Key setting MENU) 32●3・4CH (3・4Channel) 33▶2WAY（2WAY） 33▶3WAY（3WAY） 33▶5WAY（5WAY） 34▶ANALOG (Analog mixing MENU) 34▶GYRO (GYRO mixing MENU) 34▶TWIN SERVO (Twin servo mixing MENU) 35▶4WS (4WS mixing MENU) 35▶AMP (AMP mixing MENU) 36▶T-MIX (Throttle mixing MENU) 37●TRIM SET (Trim SET MENU) 38▶STEER AUTO TRIM (Steering auto trim) 38▶STEER AUTO BALANCE (Steering auto balance Left) 38▶STEER AUTO BALANCE (Steering auto balance Right) 38●SYSTEM MENU 39▶DISPLAY MENU 39▶BATTERY TYPE 39！WARNING！　Warning Display　 40▶CALCULATOR 41▶SOUND MENU 41▶VR INFORMATION　Volume information 41▶KEYSPEED　 42▶OPERATIN ALARM　 42□■□STEERING MENU 43●TRAVEL MENU 43▶ST TRAVEL　Steering Travel 43▶ST BALANCE L R　Seering Balance L R 43●TRIM MENU 44▶ST TRIM　Steering Trim 44▶ST SUBTRIM　Steering Subtrim 44▶ST TRIMRATE　Steering Trimrate 44●ST SPEED　Steering Speed 45▶ST TURN　Steering Turn Speed 45▶ST RETURN　Steering Return Speed 45●DYNAMC　Steering Dynamics 46▶CURVE　Steering curve 46▶PUNCH　Steering punch 46●FEEL MENU 47▶ST FEEL Steering feel MENU 47●REVERSE Steering Reverse 47▶ST REVERSE　Steering Reverse 47□□■THROTTLE MENU 48●TRAVEL　Throttle travel 48▶TH TRAVEL F　Throttle Travel F 48▶TH TRAVEL B　Throttle Travel B 48●TRIM MENU 49▶TH TRIM　Throttle Trim 49▶TH SUBTRIM　Throttle Subtrim 49▶TH TRIMRATE　Throttle Trimrate 49●TH SPEED　Throttle Speed 50▶TH TURN　Throttle Turn Speed 50▶TH RETURN　Throttle Return Speed 50●DYNAMC　Throttle Dynamics 51▶CURVE　Throttle Curve 51▶PUNCH　Throttle punch 51●FEEL　Throttle feel MENU 52▶TH FEEL　Throttle feel 52●OVERRIDE　Throttle Override 53●REVERSE　Throttle Reverse 53▶TH REVERSE　Throttle Reverse 53●CYCLE　Throttle Cycle 54▶ACCEL　Throttle Acceleration 54▶ABS　Throttle ABS 54●ATSTART　Throttle Auto-Start 55●OFFSET　Throttle OFFSET 56■ Glossary 57■ Repair policy 60■ Specications 61
Due to the nature of radio controlled models, improper handling may lead to dangerous situations. Therefore please read the following information carefully in order to ensure safe operation. Please also understand that KO Propo is not responsible for any injuries or damage which result from noncompliance of these cautions and notices.●When Installing Components●Notes for Usage●Make sure metal parts on the model (car chassis/ship hull) do not come into contact with each other.※Contact between metal parts may result in noise, which could cause the receiver to malfunction and lead to an uncontrollable model.●Do not cut or bundle the antenna cable.※This may lower the receiver's sensitivity and lead to an uncontrollable model.●Ensure correct polarity when installing transmitter and receiver batteries.※Incorrect polarity may damage the product.●Within Japan, this product is limited to usage with models which operate on the ground or in the water.※Do not use for other non-designated purposes.●Ensure that all connectors (receiver, servo, switch, etc.) are connected securely.※If connections become loose due to vibrations, it may lead to an uncontrollable model.●Securely attach receiver with thick double-sided tape and ensure that it does not make contact with other parts.※Strong shocks or contact with other parts due to vibrations may lead to an uncontrollable model.●Check servo operation to ensure the pushrod is not subject to excessive loads.※Excessive loads may damage the servo or increase battery power consumption.●Make sure to use the rubber grommet when attaching the servo and that the servo does not contact the R/C equipment tray.※If vibrations affect the servo, it may lead to damage or an uncontrollable model.●Use in conjunction with genuine official KO Propo products.※KO Propo is not responsible for any damages or injuries which result from use of this product in combination with other manufacturer's products.●Do not use when there is thunder.※It is possible for lightning to strike the antenna.●Do not use in the rain or in areas where water has accumulated.※If water enters the product it may lead to an uncontrollable model.●Do not use in the following locations:1. Near R/C circuits (within 3km) 2. Near crowds, on streets, or near actual vehicles or ships.3. Near high-voltage power lines or communication facilities.※If signal interference, etc. causes an uncontrollable model, a serious accident may result.●Do not use when your concentration levels are compromised by tiredness, alcohol, medication, etc.※Mistakes in judgment may result in serious accidents.●Do not allow glow engine fuel or engine exhaust to contact the product.※These may attack the plastic and damage the product.●Check to ensure that the selected model memory matches the model to be controlled.※Using an incorrect memory may lead to an uncontrollable model.●Make sure to stop the engine (disconnect motor cables) before changing transmitter settings.Warning! Improper handling/usage may lead to a high probability of material damage as well as a possibility of serious personal injury or even death.Notice! Improper handling/usage may lead to personal injury or material damage.  Warning!Enforcement matters  Warning!Prohibited matters  Warning!Prohibited matters  Warning!Enforcement matters3■ For Safe Operation
●Notes After Usage●Transmitter Battery Handling and Charging (separately available option)  Caution!Enforcement matters  Caution!Enforcement matters  Danger!Enforcement matters  Danger!Enforcement matters●Do not touch engine, motor, ESC, etc. immediately after use as they may be hot.※Doing so may lead to burns.●When switching on, always turn on the transmitter first, followed by the receiver. Follow the reverse order when switching off.※If the wrong order is followed, it may lead to an uncontrollable model.●Dismantling or modifying the RF Module (internalized in the case of the EX-2) is prohibited and is punishable by law.※Doing so may lead to accidents such as short circuits and KO Propo Customer Service Department may not accept dismantled/modified products for repair.●Do not use this product in aircraft, hospitals, or near fire alarms or medical equipment.※This may lead to malfunctions and result in serious accidents. Also, by law you must cease operation if the product affects other wireless or electrical devices.●2.4GHz transmitters must be registered with the Japan Radio Control Safety Association.※The transmitter which you have purchases is already registered. Products which do not have proof of registration are illegal.●In the case of an R/C car, make sure to remove the battery pack after driving.※If the car is switched on accidentally, it may lead to a fire or an uncontrollable model.●Keep transmitters, batteries, and models away from small children.※Chemical agents and the items themselves may cause personal injury.●Remove batteries from transmitter if it will not be used for a considerable time.※If batteries are left in the transmitter, battery leakage may result in damage.●Do not store transmitter/receiver in the following conditions:1. Extremely hot (over 40ºC) or cold (below 10ºC) temperatures.2. Locations in direct sunlight.3. Locations with high humidity.4. Locations subject to vibrations.5. Locations with lots of dust.※These conditions may cause the case to deform and damage the product.●Never short-circuit the battery connector.※This may lead to a fire or explosion.●Do not dispose batteries in fires.※This is very dangerous and may lead to an explosion.●Use KO Propo chargers to charge the battery and use the correct current (under 1A).※Incorrect current may lead to battery damage, overheating, or leakage.※Other manufacturer's chargers may not have a automatic cutoff function.●Do not subject the battery to strong shocks.※This may damage the battery and cause leakage or a short circuit.●Do not dismantle or modify the battery.※This may cause dangerous leakage of battery fluids.●Keep away from water. Do not charge a wet battery.※This may cause overheating and damage.●Do not charge alkaline batteries.※Alkaline and other single-use batteries cannot be recharged. Doing so may lead to fire and damage.●Do not use wet hands when plugging in the charger's AC Adapter.※This may result in electrical shocks.※If there is battery fluid leakage, avoid contact with eyes as it may result in blindness. If contact with eyes occur, flush with large amounts of water and seek medical attention immediately.※When disposing batteries, Ni-Cd, Ni-MH, Li-Po, and Li-Fe batteries should be recycled in order to help protect the environment.  Warning!Enforcement matters  Caution!Prohibited matters4
①① ②②③③①① ②②③③①①②②5■ Getting StartedInsert the Grip Unit into the Master Unit, then attach the Steering Unit.Detach the Steering Unit, then detach the Master Unit.● Transmitter Assembly ● Transmitter Dismantling1.1.2.2.3.3.Remove the connector cover before use.If storing the transmitter in dismantled form, please remember to attach the connector covers.Assembly may di󰮏er with the included set contents.[Legend] P:Point :NoticeSteering Unit Release ButtonSteering Unit Release ButtonSteering Unit Lock LeverSteering Unit Lock LeverGrip Unit Lock Lever Grip Unit Release ButtonGrip UnitMaster UnitMaster UnitSteering UnitSteering Unit
6AntennaEXP Connector CoverPower Switch（P.8）Charger Jack（P.8）LEDSteering Unit Release Button（P.5）Colored Grip （p.7）Colored Pad（P.7）● ET Keys (1-5) and BT Button (1)　Functions may be assigned to the 　　　keys/button.※ Only Expert grip unit available.(No.10526) 　There is no ET4/5 keys in the following sets.　No80561EX-2 Standard edition　Guard BarSteering Unit Lock Lever（P.5）※ Open the cover　（Only Expert Grip)Throttle Trigger（P.7）Grip Unit Lock Lever（P.5）Grip UnitRelease Button（P.5）Throttle TriggerPosition Adjuster（P.7）ET1（P.7）BT1（P.7）ET2（P.7）ET4（P.7）ET5（P.7）ET3（P.7）■ Names of Parts《Front View》《Side View》《Rear View》The possible functions which each key/button may be assigned to are di󰮏erent.
The tabs on the colored grip and pad are to be inserted into holes. Note the direction.Make sure the battery box or battery pack is removed before replacing the colored grip and pad.Note direction of the of the colored grip and pad7●Steering Wheel Adjustment●Throttle Trigger Adjustment●Wheel Cap Remove●Throttle Trigger Position Adjustment●Colored Grip and Pad Replacement● ET Keys (1-5) and BT Button (1)Functions may be assigned to the keys/button.The possible functions which each key/button may be assigned to are di󰮏erent.Colored grip pad (optional) and Large/small grip pad options are available.Remove the two screws on each side of the grip to detach the grip plates, then attach the colored grip and pad.《How to change》Adjust the tension of the steering wheel spring.Insert a 1.5mm hex wrench referring to the image below. Rotate clockwise to increase tension and counterclockwise to decrease it.[How to Adjust]Hex WrenchExcessive counterclockwise rotation will result in the wheel being unable to return to neutral position. In this case, rotate clockwise until the wheel returns to neutral.Insert Wheel Cap Remover to the wheel cap spoke.Pull up Wheel cap remover with Wheel Cap.Adjust the position and angle of the brake trigger to your preferences.Loosen the hex screws on the throttle trigger with a 1.5mm hex wrench. Freely adjust the brake trigger position. Tighten the hex screws to secure.[How to Adjust]Throttle TriggerBrake Trigger Hex ScrewsBall JointThe position of the throttle trigger may be adjusted to match the user's hands. Loosen two screws on the rear side of the transmitter. Slide the Throttle Trigger Position Adjuster as desired. Tighten the loosened screws to secure.[How to Adjust]ScrewsThrottle TriggerPosition Adjuster
8●Unit Connector●Power SwitchThis product may be dismantled and therefore each unit features their respective connectors. Dirty or damaged connectors may result in malfunctions, so please handle them carefully.Do not touch the unit connectors with your ngers. If connectors become corroded due to grime, they may become inoperable. If storing the transmitter in dismantled form. After prolonged use, a black residue may build up on the connectors. Use cotton swabs dipped in cleaning alcohol to remove. KO Propo's Customer Service Department also handles transmitter maintenance.This product features a safety lock. The Master Unit and Grip Unit cannot be detached when the Power Switch is in the ON position. Turn off the transmitter before dismantling.Power Switch
①①①①②②②②9■ Preparations●Battery Installation ● Battery Level WarningBattery Box1.2.3.R03/AAA/UM4Batteries (4pcs.)Battery Box CoverPress the tab on the bottom of the transmitter to open battery box cover.Remove the lock to pull out battery box.Install four R03/AAA/UM4 alkaline batteries while noting their polarity, then replacebattery box.Use batteries which have adequate remaining capacity. Weak batteries mean lower transmitting power and may result in malfunctions.Do not install Ni-Cd or Ni-MH batteries in the battery box. (These may cause the battery connectors to corrode.)A warning will be displayed with the LED ashing and an alarm will sound when battery voltage is less 4v. When you see this warning, stop your model in a safe area, turn it o󰮏 and install new transmitter batteries.If the Xpansion unit is not assembled or used, do not use the LiFe/LiPo battery.
10● Initializing EX-2 ●How to change the Modulation mode 1.2.3.Power on while operating ET2 lever below.ET2ET2Power ONWhen using the EX-2 for the rst time, please carry out the following settings.※ EX-2 does will not work normally if the initial 　　　conrguration is not set.※ This is an operation method when the expansion 　unit is not assembled.Initialization is necessary 　　using a di󰮏erent method when expansion unit is 　put on, see p. 24 for more information.EX-2 has two Modulation modes.※ When attaching the Xpansion unit, this operation 　is the same.① Turn o󰮏 EX-2 switch.② Push the ET1 lever to the left and power on.③ Hold ET1 lever until the buzzer sounds and the 　　LED of EX-2 turns on (approximately two seconds). ④ Set the Fail-Safe Function（p.15）.《Functions》● General RC models FHSS mode　： LEDSolid　Operating the general receivers such as 　KR-211FH/KR-241FH ● Mini-Z MHS mode 　：　LED Flashing slowly　Oparating Kyosho Mini-Z MHS mode.　(MR-03 VE PRO)Hold the ET2 lever until the LED of EX-2 turns on (approximately two seconds).After the LED turns on, release ET2 lever.Buzzer sounds, and reset is completed.When changing each unit for a different unit, please perform this initialization again.The receiver is available for only FHSS method.The receiver of other methods (DSSS/27/40MHz) does not work.Only MiniZ for MHS is available. Does not work with the receiver for ASF, FHS, general RC cars.If the pilot LED is blinking fast, this is a warning that the battery voltage is low. Please change to new batteries or for a battery pack which has been charged.↓↓↓↓PowerON↓↓↓ET1Approximately two seconds, LED turns on.
Carbon Fiber ChassisNoise is generated in any area where a large amount of electric current is flowing. Position the receiver and antenna cable as far away from the motor, battery, ESC, and their associated cables as possible. (Metal or carbon fiber chassis components will also conduct electricity and generate noise.)Since R/C models are controlled via radio signals, taking appropriate measures against noise generated by on-board equipment is of utmost importance. Take adequate measures against noise so that your machine can fully realize your driving potential. Battery PackReceiverESC Silicon CablesMotorNoiseNoiseNoiseNoiseNoiseNoiseNoiseNoiseNoiseNoiseKeep antenna cable away from all sources of noise!When installing the receiver to the chassis or R/C equipment deck/tray, use two or more pieces of thick double-sided tape to raise the receiver off the chassis surface. By increasing the separation between the receiver and the noise-generating carbon-fiber chassis components, the effects of noise can be decreased.Raise the antenna cable vertically from as high a position as possible. Insert the antenna cable into the antenna pipe so that the tip of the antenna aligns with the end of the pipe. Make the length of cable which runs between the receiver and the pipe as short as possible and position the antenna holder as close to the receiver as possible. Position the antenna cable away from sources of noise such as the chassis and R/C equipment deck/tray. Use an antenna pipe and antenna mount that are made from plastic, since metal parts will conduct noise.Engine vibrations may damage the receiver. Make sure to attach a grommet (receiver holder) to reduce the effects of such vibrations. Do not attach the receiver directly to the chassis or R/C equipment deck/tray with double-sided tape. Also position the receiver so that it does not contact the heat and exhaust of the engine and muffler.Plastic Antenna Pipe Plastic Antenna PipePlastic Antenna HolderGrommetAluminum Antenna HolderAluminum Antenna HolderPiano WireDouble-Sided TapeAntenna CableSignal Receiving SectionNoiseNoiseNoiseNoiseNoiseNoiseNoiseNoiseNoiseNoise(Acceptable with FRP or plastic chassis)Soldered Lug Plate● Receiver Installation on a Carbon Fiber Chassis● Antenna Installation● Installing Onto a Glow Engine Car※Install the receiver so that its LEDs are visible.※Install the receiver so that its LEDs are visible.※Do not bend or cut the antenna cable. (This may break the antenna wire and deteriorate its performance.)11● Countermeasures Against Noise
12● Receiver Installation1.2.3.4.5.Install the receiver, servo, and ESC (in the case of an electric car) onto your machine and connect them. Install the receiver while taking noise into consideration （p.11）.Install batteries into the transmitter's battery box （p.9）.In the case of an electric car, install battery pack. In the case of a glow engine car, install battery for receiver.For 2.4GHz systems, conduct pairing of the transmitter and receiver .※ In order for the receiver to operate, it must store the transmitter's unique ID in its memory in a process called “pairing.” Even if a single transmitter is used to control multiple receivers, each receiver must go through the pairing process with the transmitter before being used for the rst time.Adjust steering（p.18）and throttle/braking（p.19）.Set the Fail-Safe Function（p.15）.※ Carefully read the instructions included with the servo and ESC before installing and using them.For items which are not included in this product, please refer to the KO Propo website for a list of compatible products. (http://www.kopropo.co.jp)This transmitter is only compatible with digital servos. Correct operation is not possible when used with analog servos. ● For an Electric Car　　● For a Glow Engine Car● Battery Pack 　(Sold Separately)● Motor 　(Sold Separately)● ESC (CH2) 　(Sold Separately)● Receiver● Steering Servo (CH1)　(Sold Separately)● Steering Servo (CH2) 　(Sold Separately)● Battery for Receiver　(Sold Separately)● Receiver● Steering Servo (CH1) 　(Sold Separately)
13BATT Preparing the Transmitter① While pushing the ET2 lever up, power on.② When the ET2 lever is released, the LED turns of　 EX-2 LED lights up again (indicating transmitter is transmitting the pairing signal.)Case without the Xpansion unit※ Refer to p.25 pairing Operation in the case of using the Xpansion unit.In order for the receiver to operate, it must store the transmitter's unique ID in its memory in a process called “pairing.” Even if a single transmitter is used to control multiple receivers, each receiver must go through the pairing process with the transmitter before being used for the rst time.　※ Please adjust the Modulation mode before 　pairing.(p.10) A receiver does not work 　　normally in di󰮏erent mode.During this process, your car may become uncontrollable if the ESC has not been adjusted. As a precaution, set your car so that its wheels do not touch the ground.Pairing procedures may not go smoothly if there are wireless LAN, microwave ovens, or other users conducting pairing procedures nearby. In this case, move some distance away or wait a while before attempting the pairing procedure again.If the mode is changed（General or France), please conduct pairing procedures with the receiver you are using again.<France mode pairing ＞FRANCE mode pairing is possible when the ET2 lever is released after LED turns o󰮏. Please use this feature if the situation is needed.1.2.3.ET2ET2Power ON↓↓↓● Pairing (For general receiver) Preparing the Receiver① Connect the receiver power source while pressing the setup button.② Check that the receiver's LED has lit up, then release the setup button.③ Check that the receiver's LED lights up again (indicating pairing completion)※ When pairing is complete, pressing the ENTER key on the transmitter will return the screen to the previous [2.4Gband] menu.※ Switch o󰮏 the receiver, then switch it back on again for normal operations.※ The preparations below are to be carried out following the pairing procedure. Preparations for Operation① Switch o󰮏 the receiver.② Switch o󰮏 the EX-2 main power, then switch on EX-2 again.③ Switch on the receiver and check that the receiver LED is lit. If the LED ashes, the receiver is not getting the EX-2 signal and the pairing procedure should be repeated.Lit LEDLit LEDFlashing LED

Navigation menu