| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2644054 |
| Application ID | JdCY3qaa5+8c3r/gsNN2wg== |
| Document Description | 06_2_Users_Manual_rev1 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 426.36kB (5329469 bits) |
| Date Submitted | 2015-06-10 00:00:00 |
| Date Available | 2015-06-11 00:00:00 |
| Creation Date | 2015-05-31 14:20:40 |
| Producing Software | Adobe PDF Library 9.0 |
| Document Lastmod | 2015-05-31 14:20:55 |
| Document Title | EX-2-manual-En-0530.pdf |
| Document Creator | Adobe InDesign CS4_J (6.0.6) |
● Pairing (For MHS Mini-Z)
Case without the Xpansion unit
2. Preparing the Mini-Z
※ Refer to p.26 pairing Operation in the case of
using the Xpansion unit.
① Bring distance of EX-2 and MiniZ close to about
10cm.
In order for the Mini-Z to operate, it must store the
transmitter's unique ID in its memory in a process
called“pairing.”Mini-Z must go through the pairing
process with the transmitter before being used for
the first time.
10cm
※ Please adjust the Modulation mode
before pairing.(p.10) A receiver does
not work normally in different mode.
1. Preparing the Transmitter
① While pushing the ET2 lever up, power on.
Pushing setup botton
↓
↓
Power ON
② Switch on MiniZ while pushing the setup button
of Mini-Z.
Switch on
ET2
③ After the Mini-Z's LED has lit up, release the
setup button. Then ｃ heck that the Mini-Z's LED
lights up again (indicating pairing completion)
↓
② When the ET2 lever is released, the LED turns of
)key,
ENTER(ENT) key, and BACK key.
ENT Key: Selecting item to be modified; Confirming a change after a setting change.
L（ < ）Key: Used to move cursor between menu choices and to change a setting value.
Lowering a value (for L/R cases: raising toward L); Return to a previous menu item.
R（ > ）Key: Used to move cursor between menu choices and to change a setting value.
Raising value (for L/R cases: raising toward R); Proceed to next menu item.
BACK Key：Returning to previous screen; Canceling change
L(<) key + R(>) key Pressing simultaneously: Resets the value to default setting.
Command Button
Used for firmware upgrading.
Please refer to an update
manual for the details.
Communication port
Used for firmware upgrading
and ICS communication.
Please refer to an update
manual for the details.
BACK Key
L（ < ）Key
R（ > ）Key
ENT Key
【 Basic Operation 1: Selecting from a Menu 】
This explanation uses [Steering] as an example.
① Use the R(>) key to move the cursor over [Steering].
② Press the ENTER key to change to the Steering Menu screen.
【 Basic Operation 2: Changing a Setting Value 】
ST SPEED スピード
This explanation uses [TURN 1] on the Steering Speed screen as an example.
ST TURN
100 %
① Use R(>) key to move the cursor over the 100% value next
to [ST TURN].
ﾀｰﾝｽﾋﾟｰﾄﾞ
② Press ENTER key to select it for modification.
ST RETURN 100%
ﾘﾀｰﾝｽﾋﾟｰﾄﾞ
③ Once selected, the cursor will blink. Now use the L(<)key+R(>)key
to change the value.
④ After changing the value, press the ENTER key again to confirm the change.
ST SPEED スピード
ST TURN
ﾀｰﾝｽﾋﾟｰﾄﾞ
ST SPEED スピード
100 %
ST TURN
ﾀｰﾝｽﾋﾟｰﾄﾞ
ST RETURN 100%
ﾘﾀｰﾝｽﾋﾟｰﾄﾞ
50 %
ST RETURN 100%
ﾘﾀｰﾝｽﾋﾟｰﾄﾞ
21
● Installation of expansion unit
※ Not included with No.10555 EX-2 BASIC set.
▼ B：when mounting sideways
Xpansion unit can be mounted facing the
front or the side. The factory setting is
mounted to the front.
① Attach the monitor base at a right angle to
Xpansion Unit. ※ Different Factory setting.
Attention to the marker.
Be careful to not misuse the M2.6-6BH and TP2.68BH screws.
M2.6-6BH
x2
Xpansioun unit can be mounted in two different
directions using the monitor base and bracket..
A ▼：setting to the front
① Attach a monitor base parallel to Xpansion
unit. ※ Factory setting.
Attention to the marker.
② Attach the monitor bracket to the master
unit. ※ Apply［B ▼］mark to the steering side
M2.6-6BH
x2
TP2.6-8BH
Self tapping screws
x４
Connect the wire of the
Xpansion unit to the
master unit.
② Attach the monitor bracket to the master
unit. ※［A ▼］mark to the steering side
TP2.6-8BH
Self tapping screws
x４
Connect the wire of the
Xpansion unit to the
master unit.
③ Attach the Xpansion unit to the master unit.
※ Attach the monitor base and bracket as
shown in figure A ③ .
How to disassemble the Xpansion unit.
1.While pushing the monitor-based apart.
2.Slide the Xpansion like shown in the figure
below and take off.
※ The disassembly method is the same as side
and front positions.
③ Attach expansion unit to a master unit.
While matching the edge of the base with
the dent of the bracket, slide it until the
Xpansion unit locks.
When assembling or disassembling the Xpansion unit to
EX-2, please switch off the EX-2.
22
● Startup Screen and Initial Screen
When the transmitter is switched on, the startup screen will display, followed by the initial screen.
※ Pressing the ENTER key during the startup screen will allow you to proceed to the initial screen.
【 Startup Screen 】
① Version Information :
Displays the version of the program that is installed in the Master Unit's CPU.
This product's performance may be upgraded via paid or free upgrades.
Check the KO Propo website for information regarding such upgrades.
（ http://www.kopropo.co.jp ）
①
【 Initial Screen 】
⑤
⑥
⑦
①
⑧
②
③
⑨
④
① Function Monitor: Functions that are active will be lit up.
OR ： Steering and Brake travel Override
AUT ： Throttle Auto Start
CYC ： Cycle（Throttle Acceleration/Throttle ABS)
OFS ： Offset（Drag Brake/Idle Up）
② Steering Trim Monitor: Displays the position of the steering trim.
③ Throttle Trim Monitor: Displays the position of the throttle trim.
④ Top menu: Display three kinds of setting items
FUNCTION Modify settings related to functions.
STEERING Modify settings related to the steering.
THROTTLE Modify settings related to the throttle.
⑤ Mini-Z MODE： Functions that are in Mini-Z will be lit up.
⑥ Power Source Type: Displays the type of battery being used.
ＬＰ：Li-po
ＬＦ：Li-Fe
ＤＲ：R03/AAA/UM4 Alkaline Batteries
ＮＩ：Ni-MH
(Notice) If you switch battery types, make sure to also change the [Battery Management] setting.
⑦ Voltage: Displays the current power source voltage.
⑧ Model Number: Displays the currently selected model number.
⑨ Model Name: Displays the name of the currently selected model number.
23
● How to change the Modulation mode
● VR information setting
Adjust the steering and throttle resistance
information. ※ Please perform the VR information
configuration to calibrate your system.
○ When using EX-2 for the first time.
○ When changing a steering unit for a different
product or when putting it back together.
○ When changing a grip unit for a different product
or when putting it back together.
○ When using and confusion has occurred in the
positional information.
EX-2 has two Modulation modes.
※ When attaching the Xpansion unit, this operation
is the same.
《Functions》
● General RC models FHSS mode： LED Solid
Operating the general receivers such as KR-211FH/KR241FH Only receivers using FHSS will work.
1.Select [FUNCTION] on the initial screen and push
the ENTER key.
2.Select [SYSTEM] on the function screen and push
the ENTER key.
3.Select [VR INFO] on the system screen and push
the ENTER key.
4.Move the wheel slowly to the full left and right lock
(numbers will change as the steering is moved) and
release the wheel back to neutral.
5.Move the trigger slowly to the full throttle and full
brake positions (numbers will change as the
throttle is moved) and release the trigger back to
neutral.
6.Then select YES (press ENTER) to adjust and save
the settings.
ET1
PowerON
Right MAX
Hold
Full Throttle
Approximately two
seconds, LED turns on.
Hold
Full Brake
6, Small window [Yes] comes active.
VR INFOMATION
ST- LEFT ﾋﾀﾞﾘ
NUT ｾﾝﾀｰ
RIGHT ﾐｷﾞ
TH- HI
ｾﾞﾝｼﾝ
NUT ｾﾝﾀｰ
LOW
ﾌﾞﾚｰｷ
② Push the ET1 lever to the left and power on.
OK?
YES
4,5, Move slowly to full stroke, then release.
Left MAX
① Turn off EX-2 switch.
↓
ﾌﾞﾚｰｷ
Only MiniZ using MHS will work. Does not work with
ASF, FHS, general RC cars.
↓
↓
LOW
※ Functions that are in Mini-Z will be lit up at initial
screen.
VRｲﾝﾌｫﾒｰｼｮﾝ
2204
2198
2194
2078
2075
2072
ST- LEFT ﾋﾀﾞﾘ
NUT ｾﾝﾀｰ
RIGHT ﾐｷﾞ
TH- HI
ｾﾞﾝｼﾝ
NUT ｾﾝﾀｰ
● Mini-Z MHS mode ：LED Flashing slowly
Oparating Kyosho Mini-Z MHS mode. (MR-03 VE
PRO)
③ Hold ET1 lever until the buzzer sounds and the
LED of EX-2 turns on (approximately two seconds).
3.Example before setting
VR INFOMATION
The receiver of other methods (DSSS/27/40MHz)
do not work.
If the pilot LED is blinking fast, this is a warning
that the battery voltage is low. Please change to
new batteries or for a battery pack which has been
charged.
VRｲﾝﾌｫﾒｰｼｮﾝ
3949
2198
487
3313
2075
1463
Model selection changes and modulation mode
changes are not linked.
OK?
YES
※ When operating the VR INFORMATION and
pressing the BACK key will cancel the operation.
24
● Pairing (For general receiver)
Case of using the Xpansion unit
3. Preparations for Operation
※ Refer to p.13 pairing Operation when not using the
Xpansion unit.
① Switch off the receiver.
② Switch off the EX-2 main power,
then switch on EX-2 again.
In order for the receiver to operate, it must store the
transmitter's unique ID in its memory in a process
called“pairing.”Even if a single transmitter is used
to control multiple receivers, each receiver must go
through the pairing process with the transmitter
before being used for the first time.
③ Switch on the receiver and check
that the receiver LED is lit. If
the LED flashes, the receiver is
not getting the EX-2 signal and
the pairing procedure should be
repeated.
※ Please adjust the modulation mode before pairing.
(p.24) A receiver does not work normally in a different
mode.
Flashing LED
During this process, your car may become uncontrollable
if the ESC has not been adjusted. As a precaution, set
your car so that its wheels do not touch the ground.
1. Preparing the Transmitter
① While pushing the ET2 lever up, power on.
Pairing procedures may not go smoothly if there
are wireless LAN, microwave ovens, or other users
conducting pairing procedures nearby. In this case, move
some distance away or wait a while before attempting the
pairing procedure again.
The pilot LED lights up, release ET2 lever.
If the mode is changed（General or France), please
conduct pairing procedures with the receiver you are
using again.
↓
↓
PowerON
Lit LED
④ Set the Fail-Safe Function（p.15）.
ET2
● For an Electric Car
● Battery Pack
(Sold Separately)
↓
② Displays the initial screen, then pairing display is
shown. (indicating transmitter is transmitting the
pairing signal.)
● Motor
(Sold Separately)
● Steering Servo (CH1)
(Sold Separately)
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.6
Linearized : Yes
Create Date : 2015:05:31 14:20:40+09:00
Creator : Adobe InDesign CS4_J (6.0.6)
Modify Date : 2015:05:31 14:20:55+09:00
Trapped : False
Tagged PDF : Yes
XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date : 2015:05:31 14:20:55+09:00
Creator Tool : Adobe InDesign CS4_J (6.0.6)
Format : application/pdf
Title : EX-2-manual-En-0530.pdf
Document ID : uuid:3f73fb5d-2767-4e7d-a58e-764e9bd04318
Instance ID : uuid:f850a23b-d1ac-4706-b4ee-48eb3c505c30
Producer : Adobe PDF Library 9.0
Page Count : 15
EXIF Metadata provided by EXIF.tools