NCR RSD Atlanta 7730GAI Electronic Pricing Transmitter User Manual Appendix B

NCR Corporation, RSD - Atlanta Electronic Pricing Transmitter Users Manual Appendix B

Users Manual Appendix B

Appendix B: DecisioNet Configuration FilesThis appendix contains listings of the following DecisioNetConfiguration files:• DecisioNet CBS Configuration file (dncbsconfig.xml)• DecisioNet Configuration file (dnconfig.xml)• DecisioNet Task Manager Configuration file (taskman.cfg)• DecisioNet Host Bridge Configuration file (dnhostbridge.xml)DecisioNet CBs Configuration file (dncbsconfig.xml)<?xml version="1.0"?><!DOCTYPE cbsconfig SYSTEM "dncbsconfig.dtd"><cbsconfig><cbs><id>1</id><hostname>ncrdnetnnnnnn.atlantaga.ncr.com</hostname></cbs></cbsconfig>DecisioNet Configuration file (dnconfig.xml)<?xml version="1.0"?><!DOCTYPE config SYSTEM "dnconfig.dtd"><config><section name="Ipc"><!-- <param name="ServerIP">127.0.0.1</param> --><param name="TraceLevel">0</param></section> <!-- ************************************************************ --> <!-- * LogTally Manager Configuration parameters * -->B
B-2 Appendix B: DecisioNet Configuration Files <!-- ************************************************************ --><section name="LogTally Manager"> <!-- Section: LogTally Manager --> <!-- --> <!-- SystemLogging --> <!-- --> <!-- Specifies whether or not to log to the OS system log. d --> <!-- --> <!-- Values: Y(yes) or N(no) --> <!-- --> <!-- Default = Y (yes) --><param name="SystemLogging">Y</param> <!-- Section: LogTally Manager --> <!-- --> <!-- CheckAction --> <!-- --> <!-- Specifies whether or not to check for any actions --> <!-- required before sending event to the dnltmanager. --> <!-- --> <!-- Values: Y - Send only if action required. --> <!-- N - Send always. --> <!-- --> <!-- Default = Y (yes) --><param name="CheckAction">Y</param> <!-- Section: LogTally Manager --> <!-- --> <!-- MaxTallies --> <!-- --> <!-- Maximun number of tallies allowed per modue. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 50 --><param name="MaxTallies">50</param> <!-- Section: LogTally Manager --> <!-- --> <!-- TallyUpdateFrequency --> <!-- --> <!-- Interval to request tally dumps in minutes. --> <!-- --> <!-- Values: 1+ --> <!-- -->
Appendix B: DecisioNet Configuration Files B-3 <!-- Default = 10 --><param name="TallyUpdateFrequency">10</param> <!-- Section: LogTally Manager --> <!-- --> <!-- TraceLevel --> <!-- --> <!-- Specifies level of verbose tracing. --> <!-- --> <!-- Values: 0-4 --> <!-- --> <!-- Default = 0 --><param name="TraceLevel">0</param> <!-- Section: LogTally Manager --> <!-- --> <!-- TraceFile --> <!-- --> <!-- Specifies file name to write trace information. --> <!-- --> <!-- Values: Valid file and or dir/file name. --> <!-- --> <!-- Default = None --> <!-- <param name="TraceFile">dnltmanager.trc</param> --> <!-- Section: LogTally Manager --> <!-- --> <!-- EventsMax --> <!-- --> <!-- Specifies maximum number of records allowed --> <!-- in EVENT table. --> <!-- --> <!-- Values: 1000+ --> <!-- --> <!-- Default = 10000 --><param name="EventsMax">10000</param> <!-- Section: LogTally Manager --> <!-- --> <!-- EventsNumberToRemove --> <!-- --> <!-- Specifies number of records to delete when EventsMax --> <!-- is reached. --> <!-- --> <!-- Values: 100+ --> <!-- -->
B-4 Appendix B: DecisioNet Configuration Files <!-- Default = 1000 --><param name="EventsNumberToRemove">1000</param> <!-- Section: LogTally Manager --> <!-- --> <!-- EventsDaysToRemove --> <!-- --> <!-- Specifies maximum retention days for EVENTS. --> <!-- All EVENTS older than this number of day will be deleted.--> <!-- Parameter superseeds EventMAx. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 30 --><param name="EventsDaysToRemove">30</param> <!-- Section: LogTally Manager --> <!-- --> <!-- HandleEmail --> <!-- --> <!-- Specifies whether to handle email type actions. --> <!-- --> <!-- Values: Y(yes) or N(no) --> <!-- --> <!-- Default = Y (yes) --><param name="HandleEmail">Y</param> <!-- Section: LogTally Manager --> <!-- --> <!-- HandleAlarm --> <!-- --> <!-- Specifies whether to handle alarm type actions. --> <!-- --> <!-- Values: Y(yes) or N(no) --> <!-- --> <!-- Default = Y (yes) --><param name="HandleAlarm">Y</param> <!-- Section: LogTally Manager --> <!-- --> <!-- HandleConsole --> <!-- --> <!-- Specifies whether to handle console type actions. --> <!-- --> <!-- Values: Y(yes) or N(no) --> <!-- -->
Appendix B: DecisioNet Configuration Files B-5 <!-- Default = Y (yes) --><param name="HandleConsole">Y</param> <!-- Section: LogTally Manager --> <!-- --> <!-- HandleSystemTray --> <!-- --> <!-- Specifies whether to handle systemtray type actions. --> <!-- --> <!-- Values: Y(yes) or N(no) --> <!-- --> <!-- Default = Y (yes) --><param name="HandleSystemTray">Y</param> <!-- Section: LogTally Manager --> <!-- --> <!-- --> <!-- --> <!-- Specifies whether or not to handle the action. --> <!-- --> <!-- Values: Y(yes) or N(no) --> <!-- --> <!-- Default = Y (yes) --><param name="HandleExecProcess">Y</param> <!-- Section: LogTally Manager --> <!-- --> <!-- --> <!-- --> <!-- Specifies whether to handle Esl Pager Tag type actions. --> <!-- --> <!-- Values: Y(yes) or N(no) --> <!-- --> <!-- Default = Y (yes) --><param name="HandlePager">Y</param> <!-- Section: LogTally Manager --> <!-- --> <!-- HandleEslTag --> <!-- --> <!-- Specifies whether to handle Esl Manual Tag type actions. --> <!-- --> <!-- Values: Y(yes) or N(no) --> <!-- --> <!-- Default = Y (yes) -->
B-6 Appendix B: DecisioNet Configuration Files<param name="HandleEslTag">Y</param> <!-- Section: LogTally Manager --> <!-- --> <!-- HandleThirdParty --> <!-- --> <!-- Specifies whether to handle ThirdParty type actions. --> <!-- --> <!-- Values: Y(yes) or N(no) --> <!-- --> <!-- Default = N (No) --><param name="HandleThirdParty">N</param> <!-- Section: LogTally Manager --> <!-- --> <!-- ManualTagLinkID --> <!-- --> <!-- Specifies Manual Tag Link ID. --> <!-- --> <!-- Values: AlphaNumeric --> <!-- --> <!-- Default = MANUAL --><param name="ManualTagLinkID">MANUAL</param> <!-- Section: LogTally Manager --> <!-- --> <!-- ManualTagLinkType --> <!-- --> <!-- Specifies Manual Tag Link Type. --> <!-- --> <!-- Values: Numbeic --> <!-- --> <!-- Default = 99 --><param name="ManualTagLinkType">99</param> <!-- Section: LogTally Manager --> <!-- --> <!-- PagerTagLinkID --> <!-- --> <!-- Specifies Pager Tag Link ID. --> <!-- --> <!-- Values: AlphaNumeric --> <!-- --> <!-- Default = PAGER --><param name="PagerTagLinkID">PAGER</param>
Appendix B: DecisioNet Configuration Files B-7 <!-- Section: LogTally Manager --> <!-- --> <!-- PagerTagLinkType --> <!-- --> <!-- Specifies Pager Tag Link Type. --> <!-- --> <!-- Values: Numeric --> <!-- --> <!-- Default = 98 --><param name="PagerTagLinkType">98</param></section> <!-- ************************************************************ --> <!-- * CBS Manager Configuration parameters * --> <!-- ************************************************************ --> <section name="CBS Manager"> <!-- Section: CBS Manager --> <!-- --> <!-- MaxWorkerThreads --> <!-- --> <!-- The maximum number of threads the CBS Manager is allowed --> <!-- to create to communicate with CBS's. This parameter --> <!-- will limit the number of connections to CBS's that the --> <!-- CBS Manager can create. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 20 --> <param name="MaxWorkerThreads">20</param> <!-- Section: CBS Manager --> <!-- --> <!-- MaxConnectionsPerCBS --> <!-- --> <!-- The maximum number of connections the CBS Manager is --> <!-- allowed to have open to each individual CBS. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 10 --> <param name="MaxConnectionsPerCBS">10</param> <!-- Section: CBS Manager --> <!-- -->
B-8 Appendix B: DecisioNet Configuration Files <!-- MaxChainedMessages --> <!-- --> <!-- The maximum number of ESL commands that should be --> <!-- chained together in a single ESL message (downlink). --> <!-- --> <!-- Values: 1-8 --> <!-- --> <!-- Default = 5 --> <param name="MaxChainedMessages">5</param> <!-- Section: CBS Manager --> <!-- --> <!-- MinChainedMessages --> <!-- --> <!-- The minimum number of ESL commands that should be --> <!-- chained together in a single ESL message (downlink). If --> <!-- fewer than this number need to be sent to process a --> <!-- request NOP commands are appended to increase the number --> <!-- of chained messages. --> <!-- --> <!-- Values: 1-8 --> <!-- --> <!-- Default = 1 --> <param name="MinChainedMessages">1</param> <!-- Section: CBS Manager --> <!-- --> <!-- TODUpdateFrequency --> <!-- --> <!-- Specifies how often (in minutes) the time of day should --> <!-- be broadcast to all ESL's. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 60 (minutes) --> <param name="TODUpdateFrequency">60</param> <!-- Section: CBS Manager --> <!-- --> <!-- NumberCBSAttempts --> <!-- --> <!-- Specifies how many times the CBS Manager should attempt --> <!-- to connect to a CBS or send a command to a CBS before --> <!-- giving up. --> <!-- --> <!-- Values: 1+ --> <!-- -->
Appendix B: DecisioNet Configuration Files B-9 <!-- Default = 3 --> <param name="NumberCBSAttempts">3</param> <!-- Section: CBS Manager --> <!-- --> <!-- NumberESLAttempts --> <!-- --> <!-- Specifies how many times the CBS Manager should attempt --> <!-- to send a message to an ESL before giving up. The CBS --> <!-- Manager will retry sending a message to an ESL up to --> <!-- this limit when no response is received from the ESL. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 5 --> <param name="NumberESLAttempts">5</param> <!-- Section: CBS Manager --> <!-- --> <!-- BroadcastSends --> <!-- --> <!-- Specifies the number of times the CBS Manager should --> <!-- send broadcast messages to ESL's. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 5 --> <param name="BroadcastSends">5</param> <!-- Section: CBS Manager --> <!-- --> <!-- ConnectTimeout --> <!-- --> <!-- The number of seconds the CBS Manager should wait while --> <!-- attempting to open a connection to a CBS before giving --> <!-- up. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 10 seconds --> <param name="ConnectTimeout">10</param> <!-- Section: CBS Manager --> <!-- --> <!-- ResponseTimeout --> <!-- -->
B-10 Appendix B: DecisioNet Configuration Files <!-- The number of seconds the CBS Manager should wait for a --> <!-- response from a CBS before disconnecting and retrying. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 15 seconds --> <param name="ResponseTimeout">15</param> <!-- Section: CBS Manager --> <!-- --> <!-- MaxFailureFrequency --> <!-- --> <!-- The maximum frequency in seconds that diagnostic --> <!-- failures from each CBS should be logged. The CBS --> <!-- Manager will accept no more than one diagnostic failure --> <!-- from each CBS during this window. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 15 seconds --> <param name="MaxFailureFrequency">15</param> <!-- Section: CBS Manager --> <!-- --> <!-- ResultTableExpirationTime --> <!-- --> <!-- Specifies how long (in minutes) the CBS Manager should --> <!-- keep results of completed requests in it's result table --> <!-- for retrieval by clients. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 60 minutes --> <param name="ResultTableExpirationTime">60</param> <!-- Section: CBS Manager --> <!-- --> <!-- BufferFullAttempts --> <!-- --> <!-- Specifies how many times the CBS Manager should try --> <!-- sending a message to an ESL when a CBS returns "buffer --> <!-- full." --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 99 -->
Appendix B: DecisioNet Configuration Files B-11 <param name="BufferFullAttempts">99</param> <!-- Section: CBS Manager --> <!-- --> <!-- BufferFullPause --> <!-- --> <!-- Specifies how many seconds the CBS Manager whould wait --> <!-- before resending a message to a CBS after receiving a --> <!-- "buffer full" error. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 10 --> <param name="BufferFullPause">10</param> <!-- Section: CBS Manager --> <!-- --> <!-- CBSBusyAttempts --> <!-- --> <!-- Specifies how many times the CBS Manager should try --> <!-- sending a message to an ESL when a CBS returns "busy," --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 99 --> <param name="CBSBusyAttempts">99</param> <!-- Section: CBS Manager --> <!-- --> <!-- CBSBusyPause --> <!-- --> <!-- Specifies how many seconds the CBS Manager whould wait --> <!-- before resending a message to a CBS after receiving a --> <!-- "busy" error. --> <!-- --> <!-- Values: 1+ --> <!-- --> <!-- Default = 10 --> <param name="CBSBusyPause">10</param> <!-- Section: CBS Manager --> <!-- --> <!-- QuickFind --> <!-- --> <!-- If enabled the CBS Manager will return the results of a --> <!-- find immediately after recieving a response from the ESL --> <!-- being located. If disabled the CBS Manager will -->
B-12 Appendix B: DecisioNet Configuration Files <!-- continue trying to find the specified ESL --> <!-- 'BroadcastSends' times to make sure the find returns --> <!-- the CBS that received the strongest response from the --> <!-- ESL. --> <!-- --> <!-- Values: 1 (enabled) or 0 (disabled) --> <!-- --> <!-- Default = 1 --> <param name="QuickFind">1</param> <!-- Section: CBS Manager --> <!-- --> <!-- SimulationMode --> <!-- --> <!-- If set to 1 the CBS Manager will simulate communications --> <!-- with CBS's and ESL's. If set to 2 the CBS Manager will --> <!-- send ESL messages to CBS's but always return a good --> <!-- uplink from the ESL, whether or not the actual received --> <!-- uplink was good. --> <!-- --> <!-- Values: 0, 1, or 2. --> <!-- --> <!-- Default = 0 --> <param name="SimulationMode">1</param> <!-- Section: CBS Manager --> <!-- --> <!-- StoreID --> <!-- --> <!-- The StoreID for the system. When the CBS Manager starts --> <!-- it will ensure that all CBS's use the specified store ID --> <!-- in beacons and all downlinks. --> <!-- --> <!-- Values: 0-255 --> <!-- --> <!-- Default = 255 --> <param name="StoreID">255</param> <!-- Section: CBS Manager --> <!-- --> <!-- TraceLevel --> <!-- --> <!-- Specifies the default trace level to use if none --> <!-- specified on the command-line. --> <!-- --> <!-- Trace level 0 = No trace output. --> <!-- Trace level 1 = Trace output for errors only. -->
Appendix B: DecisioNet Configuration Files B-13 <!-- Trace level 2 = Level 1 + CBS communications trace --> <!-- output. --> <!-- Trace level 3 = Level 2 + API-level function entry/exit. --> <!-- Trace level 4 - 6 = More function entry/exit output. --> <!-- --> <!-- Values: 0-6 --> <!-- --> <!-- Default = 0 --> <param name="TraceLevel">0</param> <!-- Section: CBS Manager --> <!-- --> <!-- TraceFile --> <!-- --> <!-- Specifies the name of a file where trace output should --> <!-- be written if none specified on the command-line. --> <!--<param name="TraceFile">cbsmanager.trc</param>--> </section> <!-- End CBS Manager Section --> <!-- ************************************************************ --> <!-- * ESL Manager Configuration parameters * --> <!-- ************************************************************ --> <section name="ESL Manager"> <!-- Section: ESL Manager --> <!-- --> <!-- PeriodicVerify --> <!-- --> <!-- Whether the ESL Manager is enabled to schedule automatic --> <!-- periodic verifies. --> <!-- --> <!-- Values: 0(=disabled)/1(=enabled) --> <!-- --> <!-- default = 1 (enabled) --> <param name="PeriodicVerify">0</param> <!-- Section: ESL Manager --> <!-- --> <!-- VerificationRecurrence --> <!-- -->
B-14 Appendix B: DecisioNet Configuration Files <!-- How often automatically scheduled Verifications take --> <!-- place (Price Verifier) --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = hourly (P0Y0M0DT1H0M0S) --> <!-- --> <!-- Note: only used if PeriodicVerify is enabled --> <param name="VerificationRecurrence">P0Y0M0DT1H0M0S</param> <!-- Section: ESL Manager --> <!-- --> <!-- VerificationStartDate --> <!-- --> <!-- The effective start date of automatic verifications. --> <!-- Note that this parameter just gives a starting --> <!-- point for the recurrence. It does not have to be --> <!-- absolute, nor does it have to be continuously updated. --> <!-- It simply gives A start date and time as a jumping off --> <!-- point for use with the associated recurrence. --> <!-- For example: If the action is desired every Monday at --> <!-- 1am, then the recurrence would be P0Y0M7DT0H0M0S, and --> <!-- the start date could be ANY date in the past that --> <!-- happened to be a Monday, along with a time of 1am, --> <!-- say 20010205010000 --> <!-- --> <!-- Values: valid time stamp (YYYYMMDDhhmmss) --> <!-- --> <!-- default (if missing or invalid) = time config file read --> <!-- --> <!-- Note: only used if PeriodicVerify is enabled --> <!-- <param name="VerificationStartDate">20000101000000</param> --> <!-- Section: ESL Manager --> <!-- --> <!-- PeriodicExistenceBedcheck --> <!-- --> <!-- Whether the ESL Manager is enabled to schedule automatic --> <!-- periodic existence bedchecks. --> <!-- --> <!-- Values: 0(=disabled)/1(=enabled) --> <!-- --> <!-- default = 1 (enabled) --> <param name="PeriodicExistenceBedcheck">0</param>
Appendix B: DecisioNet Configuration Files B-15 <!-- Section: ESL Manager --> <!-- --> <!-- ExistenceBedcheckRecurrence --> <!-- --> <!-- How often automatically scheduled Existence Bedchecks --> <!-- take place --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = weekly (P0Y0M7DT0H0M0S) --> <!-- --> <!-- Note: only used if PeriodicExistenceBedcheck is enabled --> <param name="ExistenceBedcheckRecurrence">P0Y0M7DT0H0M0S</param> <!-- Section: ESL Manager --> <!-- --> <!-- ExistenceBedcheckStartDate --> <!-- --> <!-- The effective start date of automatic ExistenceBedchecks --> <!-- Note that this parameter just gives a starting --> <!-- point for the recurrence. It does not have to be --> <!-- absolute, nor does it have to be continuously updated. --> <!-- It simply gives A start date and time as a jumping off --> <!-- point for use with the associated recurrence. --> <!-- For example: If the action is desired every Monday at --> <!-- 1am, then the recurrence would be P0Y0M7DT0H0M0S, and --> <!-- the start date could be ANY date in the past that --> <!-- happened to be a Monday, along with a time of 1am, --> <!-- say 20010205010000 --> <!-- --> <!-- Values: valid time stamp (YYYYMMDDhhmmss) --> <!-- --> <!-- default (if missing or invalid) = time config file read --> <!-- --> <!-- Note: only used if PeriodicExistenceBedcheck is enabled --> <!-- <param name="ExistenceBedcheckStartDate">20000101000000</param> --> <!-- Section: ESL Manager --> <!-- --> <!-- PeriodicHardwareBedcheck --> <!-- --> <!-- Whether the ESL Manager is enabled to schedule automatic --> <!-- periodic hardware bedchecks. --> <!-- --> <!-- Values: 0(=disabled)/1(=enabled) -->
B-16 Appendix B: DecisioNet Configuration Files <!-- --> <!-- default = 1 (enabled) --> <param name="PeriodicHardwareBedcheck">0</param> <!-- Section: ESL Manager --> <!-- --> <!-- HardwareBedcheckRecurrence --> <!-- --> <!-- How often automatically scheduled Hardware Bedchecks --> <!-- take place --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = monthly (P0Y1M0DT0H0M0S) --> <!-- --> <!-- Note: only used if PeriodicHardwareBedcheck is enabled --> <param name="HardwareBedcheckRecurrence">P0Y1M0DT0H0M0S</param> <!-- Section: ESL Manager --> <!-- --> <!-- HardwareBedcheckStartDate --> <!-- --> <!-- The effective start date of automatic HardwareBedchecks --> <!-- Note that this parameter just gives a starting --> <!-- point for the recurrence. It does not have to be --> <!-- absolute, nor does it have to be continuously updated. --> <!-- It simply gives A start date and time as a jumping off --> <!-- point for use with the associated recurrence. --> <!-- For example: If the action is desired every Monday at --> <!-- 1am, then the recurrence would be P0Y0M7DT0H0M0S, and --> <!-- the start date could be ANY date in the past that --> <!-- happened to be a Monday, along with a time of 1am, --> <!-- say 20010205010000 --> <!-- --> <!-- Values: valid time stamp (YYYYMMDDhhmmss) --> <!-- --> <!-- default (if missing or invalid) = time config file read --> <!-- --> <!-- Note: only used if PeriodicHardwareBedcheck is enabled --> <!-- <param name="HardwareBedcheckStartDate">20000101000000</param> --> <!-- Section: ESL Manager --> <!-- -->
Appendix B: DecisioNet Configuration Files B-17 <!-- PeriodicSumcheckBedcheck --> <!-- --> <!-- Whether the ESL Manager is enabled to schedule automatic --> <!-- periodic sumcheck bedchecks. --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- Values: 0(=disabled)/1(=enabled) --> <!-- --> <!-- default = 1 (enabled) --> <param name="PeriodicSumcheckBedcheck">0</param> <!-- Section: ESL Manager --> <!-- --> <!-- SumcheckBedcheckRecurrence --> <!-- --> <!-- How often automatically scheduled Sumcheck (data) --> <!-- Bedchecks take place --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = daily (P0Y0M1DT0H0M0S) --> <!-- --> <!-- Note: only used if PeriodicSumcheckBedcheck is enabled --> <param name="SumcheckBedcheckRecurrence">P0Y0M1DT0H0M0S</param> <!-- Section: ESL Manager --> <!-- --> <!-- SumcheckBedcheckStartDate --> <!-- --> <!-- The effective start date of automatic SumcheckBedchecks --> <!-- Note that this parameter just gives a starting --> <!-- point for the recurrence. It does not have to be --> <!-- absolute, nor does it have to be continuously updated. --> <!-- It simply gives A start date and time as a jumping off --> <!-- point for use with the associated recurrence. --> <!-- For example: If the action is desired every Monday at --> <!-- 1am, then the recurrence would be P0Y0M7DT0H0M0S, and --> <!-- the start date could be ANY date in the past that --> <!-- happened to be a Monday, along with a time of 1am, --> <!-- say 20010205010000 --> <!-- --> <!-- Values: valid time stamp (YYYYMMDDhhmmss) --> <!-- --> <!-- default (if missing or invalid) = time config file read --> <!-- -->
B-18 Appendix B: DecisioNet Configuration Files <!-- Note: only used if PeriodicSumcheckBedcheck is enabled --> <!-- <param name="SumcheckBedcheckStartDate">20000101000000</param> --> <!-- Section: ESL Manager --> <!-- --> <!-- TransactionRecordLifetime --> <!-- --> <!-- How long after a transaction completes does --> <!-- the transaction record remain in the transaction log --> <!-- table? --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 2 hours (P0Y0M0DT2H0M0S) --> <param name="TransactionRecordLifetime">P0Y0M0DT2H0M0S</param> <!-- Section: ESL Manager --> <!-- --> <!-- SuccessfulSpoolRecordLifetime --> <!-- --> <!-- How long after a successful spool record completes --> <!-- does the spool log record remain in the spool log table? --> <!-- Note that update image requests associated with spool --> <!-- records being deleted are deleted from the update image --> <!-- table --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 1 minute (P0Y0M0DT0H1M0S) --> <param name="SuccessfulSpoolRecordLifetime">P0Y0M0DT0H1M0S</param> <!-- Section: ESL Manager --> <!-- --> <!-- ErroredSpoolRecordLifetime --> <!-- --> <!-- How long after a spool record completes with errors --> <!-- does the spool log record remain in the spool log table? --> <!-- Note that update image requests associated with spool --> <!-- records being deleted are deleted from the update image --> <!-- table --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 3 days (P0Y0M3DT0H0M0S) -->
Appendix B: DecisioNet Configuration Files B-19 <param name="ErroredSpoolRecordLifetime">P0Y0M3DT0H0M0S</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxNumberUpdateRetries --> <!-- --> <!-- Maximum number of times an update request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: non negative integer --> <!-- --> <!-- default = 10 --> <param name="MaxNumberUpdateRetries">10</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxUpdateRetryPeriod --> <!-- --> <!-- Maximum amount of time an update request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 10 minutes (P0Y0M0DT0H10M0S) --> <param name="MaxUpdateRetryPeriod">PT10M</param> <!-- Section: ESL Manager --> <!-- --> <!-- MinNumberUpdateRetries -->
B-20 Appendix B: DecisioNet Configuration Files <!-- --> <!-- Minimum number of times an update request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: non negative integer --> <!-- --> <!-- default = 2 --> <param name="MinNumberUpdateRetries">2</param> <!-- Section: ESL Manager --> <!-- --> <!-- MinUpdateRetryPeriod --> <!-- --> <!-- Minimum amount of time an update request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 1 second (P0Y0M0DT0H0M1S) --> <param name="MinUpdateRetryPeriod">PT1S</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxNumberBedcheckRetries --> <!-- --> <!-- Maximum number of times an Bedcheck request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so -->
Appendix B: DecisioNet Configuration Files B-21 <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: non negative integer --> <!-- --> <!-- default = 10 --> <param name="MaxNumberBedcheckRetries">10</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxBedcheckRetryPeriod --> <!-- --> <!-- Maximum amount of time an Bedcheck request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 10 minutes (P0Y0M0DT0H10M0S) --> <param name="MaxBedcheckRetryPeriod">PT10M</param> <!-- Section: ESL Manager --> <!-- --> <!-- MinNumberBedcheckRetries --> <!-- --> <!-- Minimum number of times an Bedcheck request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: non negative integer --> <!-- --> <!-- default = 2 -->
B-22 Appendix B: DecisioNet Configuration Files <param name="MinNumberBedcheckRetries">2</param> <!-- Section: ESL Manager --> <!-- --> <!-- MinBedcheckRetryPeriod --> <!-- --> <!-- Minimum amount of time an Bedcheck request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 1 second (P0Y0M0DT0H0M1S) --> <param name="MinBedcheckRetryPeriod">PT1S</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxNumberFindRetries --> <!-- --> <!-- Maximum number of times an Find request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: non negative integer --> <!-- --> <!-- default = 2 --> <param name="MaxNumberFindRetries">2</param> <!-- Section: ESL Manager --> <!-- -->
Appendix B: DecisioNet Configuration Files B-23 <!-- MaxFindRetryPeriod --> <!-- --> <!-- Maximum amount of time an Find request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 5 minutes (P0Y0M0DT0H10M0S) --> <param name="MaxFindRetryPeriod">PT5M</param> <!-- Section: ESL Manager --> <!-- --> <!-- MinNumberFindRetries --> <!-- --> <!-- Minimum number of times an Find request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: non negative integer --> <!-- --> <!-- default = 0 --> <param name="MinNumberFindRetries">0</param> <!-- Section: ESL Manager --> <!-- --> <!-- MinFindRetryPeriod --> <!-- --> <!-- Minimum amount of time an Find request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying -->
B-24 Appendix B: DecisioNet Configuration Files <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 1 second (P0Y0M0DT0H0M1S) --> <param name="MinFindRetryPeriod">PT1S</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxNumberAssignRetries --> <!-- --> <!-- Maximum number of times an Assign request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: non negative integer --> <!-- --> <!-- default = 10 --> <param name="MaxNumberAssignRetries">10</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxAssignRetryPeriod --> <!-- --> <!-- Maximum amount of time an Assign request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 10 minutes (P0Y0M0DT0H10M0S) -->
Appendix B: DecisioNet Configuration Files B-25 <param name="MaxAssignRetryPeriod">PT10M</param> <!-- Section: ESL Manager --> <!-- --> <!-- MinNumberAssignRetries --> <!-- --> <!-- Minimum number of times an Assign request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: non negative integer --> <!-- --> <!-- default = 2 --> <param name="MinNumberAssignRetries">2</param> <!-- Section: ESL Manager --> <!-- --> <!-- MinAssignRetryPeriod --> <!-- --> <!-- Minimum amount of time an Assign request is retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 1 second (P0Y0M0DT0H0M1S) --> <param name="MinAssignRetryPeriod">PT1S</param>
B-26 Appendix B: DecisioNet Configuration Files <!-- Section: ESL Manager --> <!-- --> <!-- MaxNumberForceSearchModeRetries --> <!-- --> <!-- Maximum number of times an ForceSearchMode request is --> <!-- retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: non negative integer --> <!-- --> <!-- default = 10 --> <param name="MaxNumberForceSearchModeRetries">10</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxForceSearchModeRetryPeriod --> <!-- --> <!-- Maximum number of times an ForceSearchMode request is --> <!-- retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 10 minutes (P0Y0M0DT0H10M0S) --> <param name="MaxForceSearchModeRetryPeriod">PT10M</param> <!-- Section: ESL Manager --> <!-- --> <!-- MinNumberForceSearchModeRetries --> <!-- --> <!-- Maximum number of times an ForceSearchMode request is --> <!-- retried -->
Appendix B: DecisioNet Configuration Files B-27 <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: non negative integer --> <!-- --> <!-- default = 2 --> <param name="MinNumberForceSearchModeRetries">2</param> <!-- Section: ESL Manager --> <!-- --> <!-- MinForceSearchModeRetryPeriod --> <!-- --> <!-- Maximum number of times an ForceSearchMode request is --> <!-- retried --> <!-- at the ESL Manager level when errors occur. After --> <!-- retries are exhausted, spool record is marked with last --> <!-- error received. The record is always retried so that --> <!-- both the minimum number of retries have been done and so --> <!-- that the minimum retry period has elapsed, but retrying --> <!-- stops when either the maximum number of retries have --> <!-- have been done or the maximum retry period has elapsed, --> <!-- whichever comes first. --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 1 second (P0Y0M0DT0H0M1S) --> <param name="MinForceSearchModeRetryPeriod">PT1S</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxCBSUpdateResponseWait --> <!-- --> <!-- How long does the ESL Manager wait for a "fire event" --> <!-- from the CBS Manager before explicit requesting the --> <!-- results of a spool log transaction? --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 5 minutes (P0Y0M0DT0H5M0S) -->
B-28 Appendix B: DecisioNet Configuration Files <param name="MaxCBSUpdateResponseWait">PT5M</param> <!-- Section: ESL Manager --> <!-- --> <!-- SumcheckCorrectiveAction --> <!-- --> <!-- When a sumcheck (data) bedcheck fails, should corrective --> <!-- action be taken automatically? If so, a FORCED update --> <!-- is issued for the ESL that failed. --> <!-- --> <!-- Values: 0(=disabled)/1(=enabled) --> <!-- --> <!-- default = 1 (enabled) --> <param name="SumcheckCorrectiveAction">1</param> <!-- Section: ESL Manager --> <!-- --> <!-- PingUnresponsiveTags --> <!-- --> <!-- When tags fail to respond to a find command, should --> <!-- the tags be periodically "pinged" (i.e. another find --> <!-- issued) to see if the ESL comes back into communication? --> <!-- --> <!-- Values: 0(=disabled)/1(=enabled) --> <!-- --> <!-- default = 1 (enabled) --> <param name="PingUnresponsiveTags">1</param> <!-- Section: ESL Manager --> <!-- --> <!-- IgnoreUnresponsiveTags --> <!-- --> <!-- When tags fail to respond to a find command, they are --> <!-- marked as unresponsive. Should such unresponsive tags --> <!-- be ignored for future updates, bedchecks, and verifies? --> <!-- It may be desirable to continue to send commands to --> <!-- unresponsive tags in cases of high noise, etc. --> <!-- --> <!-- Values: 0(=disabled)/1(=enabled) --> <!-- --> <!-- default = 1 (enabled) --> <param name="IgnoreUnresponsiveTags">1</param>
Appendix B: DecisioNet Configuration Files B-29 <!-- Section: ESL Manager --> <!-- --> <!-- AutoFindAfterNoResponse --> <!-- --> <!-- When a tag gives no response after an update, bedcheck, --> <!-- or verify, should there be an automatic find to try to --> <!-- locate these tags? It may be desirable to turn off auto --> <!-- find in coordination with turning off the --> <!-- IgnoreUnresponsiveTags flag in situations with high --> <!-- noise. --> <!-- --> <!-- Values: 0(=disabled)/1(=enabled) --> <!-- --> <!-- default = 1 (enabled) --> <param name="AutoFindAfterNoResponse">1</param> <!-- Section: ESL Manager --> <!-- --> <!-- SearchModeAfterNotFound --> <!-- --> <!-- When a tag gives no response after a find has been --> <!-- issued, should the ESL Manager send a command to try --> <!-- to place the tag in to search mode in an effort to --> <!-- reestablish communications (under the assumption that --> <!-- the tag may be able to hear the CBS but not vice versa)? --> <!-- --> <!-- Values: 0(=disabled)/1(=enabled) --> <!-- --> <!-- default = 1 (enabled) --> <param name="SearchModeAfterNotFound">1</param> <!-- Section: ESL Manager --> <!-- --> <!-- AutoAssignAfterFind --> <!-- --> <!-- When a tag is found after a find is issued, should an --> <!-- automatic assign be issued? --> <!-- --> <!-- Values: 0(=disabled)/1(=enabled) --> <!-- --> <!-- default = 1 (enabled) --> <param name="AutoAssignAfterFind">1</param>
B-30 Appendix B: DecisioNet Configuration Files <!-- Section: ESL Manager --> <!-- --> <!-- ForceSearchModeAfterFindFail --> <!-- --> <!-- When a tag does not respond to a find, should the ESL --> <!-- Manager send a command to force the tag to go into --> <!-- search mode? --> <!-- --> <!-- Values: 0(=disabled)/1(=enabled) --> <!-- --> <!-- default = 1 (enabled) --> <param name="ForceSearchModeAfterFindFail">1</param> <!-- Section: ESL Manager --> <!-- --> <!-- UnresponsiveTagRecurrence --> <!-- --> <!-- How often does the ESL Manager ping unresponsive tags? --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = daily (P0Y0M1DT0H0M0S) --> <!-- --> <!-- Note: only used if PingUnresponseTags is enabled --> <param name="UnresponseTagRecurrence">P0Y0M1DTH0M0S</param> <!-- Section: ESL Manager --> <!-- --> <!-- UnresponsiveTagStartDate --> <!-- --> <!-- The effective start date of automatic UnresponsiveTags --> <!-- Note that this parameter just gives a starting --> <!-- point for the recurrence. It does not have to be --> <!-- absolute, nor does it have to be continuously updated. --> <!-- It simply gives A start date and time as a jumping off --> <!-- point for use with the associated recurrence. --> <!-- For example: If the action is desired every Monday at --> <!-- 1am, then the recurrence would be P0Y0M7DT0H0M0S, and --> <!-- the start date could be ANY date in the past that --> <!-- happened to be a Monday, along with a time of 1am, --> <!-- say 20010205010000 --> <!-- --> <!-- Values: valid time stamp (YYYYMMDDhhmmss) --> <!-- -->
Appendix B: DecisioNet Configuration Files B-31 <!-- default (if missing or invalid) = time config file read --> <!-- --> <!-- Note: only used if PingUnresponseTags is enabled --> <!-- <param name="UnresponsiveTagStartDate">20000101000000</param> --> <!-- Section: ESL Manager --> <!-- --> <!-- PriceChecking --> <!-- --> <!-- When tags receive successful notification of an update, --> <!-- should a follow-up sumcheck (data) bedcheck be issued --> <!-- to ensure the correct information is on the tag? --> <!-- --> <!-- Values: 0(=disabled)/1(=enabled) --> <!-- --> <!-- default = 1 (enabled) --> <param name="PriceChecking">1</param> <!-- Section: ESL Manager --> <!-- --> <!-- DefaultUpdatePriority --> <!-- --> <!-- Default Priority to use for update transactions when --> <!-- no priority is specified. --> <!-- --> <!-- Values: integer 1 through 10, 1 being highest priority --> <!-- --> <!-- default = 3 --> <param name="DefaultUpdatePriority">3</param> <!-- Section: ESL Manager --> <!-- --> <!-- DefaultBedcheckPriority --> <!-- --> <!-- Default Priority to use for Bedcheck transactions when --> <!-- no priority is specified. --> <!-- --> <!-- Values: integer 1 through 10, 1 being highest priority --> <!-- --> <!-- default = 5 --> <param name="DefaultBedcheckPriority">5</param>
B-32 Appendix B: DecisioNet Configuration Files <!-- Section: ESL Manager --> <!-- --> <!-- DefaultVerifyPriority --> <!-- --> <!-- Default Priority to use for Verify transactions when --> <!-- no priority is specified. --> <!-- --> <!-- Values: integer 1 through 10, 1 being highest priority --> <!-- --> <!-- default = 7 --> <param name="DefaultVerifyPriority">7</param> <!-- Section: ESL Manager --> <!-- --> <!-- DefaultFindPriority --> <!-- --> <!-- Default Priority to use for Find transactions when --> <!-- no priority is specified. --> <!-- --> <!-- Values: integer 1 through 10, 1 being highest priority --> <!-- --> <!-- default = 10 --> <param name="DefaultFindPriority">10</param> <!-- Section: ESL Manager --> <!-- --> <!-- DefaultAssignPriority --> <!-- --> <!-- Default Priority to use for Assign transactions when --> <!-- no priority is specified. --> <!-- --> <!-- Values: integer 1 through 10, 1 being highest priority --> <!-- --> <!-- default = 3 --> <param name="DefaultAssignTimeslotPriority">3</param> <!-- Section: ESL Manager --> <!-- --> <!-- DefaultForceSearchModePriority --> <!-- --> <!-- Default Priority to use for forcing an ESL into search --> <!-- mode. --> <!-- --> <!-- Values: integer 1 through 10, 1 being highest priority -->
Appendix B: DecisioNet Configuration Files B-33 <!-- --> <!-- default = 3 --> <param name ="DefaultForceSearchModePriority">3</param> <!-- Section: ESL Manager --> <!-- --> <!-- TransactionResolveSleepTime --> <!-- --> <!-- The amount of time (in milliseconds) that the ESL --> <!-- Manager sleeps between ESL record processing during --> <!-- a transaction resolution. --> <!-- --> <!-- Values: non-negative integer --> <!-- --> <!-- default = 50 --> <param name="TransactionResolveSleepTime">50</param> <!-- Section: ESL Manager --> <!-- --> <!-- TransactionThreadSleepTime --> <!-- --> <!-- The amount of time (in milliseconds) that the ESL --> <!-- Manager sleeps between transactions during high-level --> <!-- transaction processing. --> <!-- --> <!-- Values: non-negative integer --> <!-- --> <!-- default = 500 --> <param name="TransactionThreadSleepTime">500</param> <!-- Section: ESL Manager --> <!-- --> <!-- SpoolLogThreadSleepTime --> <!-- --> <!-- The amount of time (in milliseconds) that the ESL --> <!-- Manager sleeps between spool log transaction processing --> <!-- --> <!-- Values: non-negative integer --> <!-- --> <!-- default = 200 --> <param name="SpoolLogThreadSleepTime">200</param>
B-34 Appendix B: DecisioNet Configuration Files <!-- Section: ESL Manager --> <!-- --> <!-- ProcessingThreadSleepTime --> <!-- --> <!-- The amount of time (in milliseconds) that the ESL --> <!-- Manager sleeps between processing CBS Manager requests --> <!-- --> <!-- Values: non-negative integer --> <!-- --> <!-- default = 0 --> <param name="ProcessingThreadSleepTime">0</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxHistoryDepth --> <!-- --> <!-- The maximum history depth for any type of transaction --> <!-- sequence. --> <!-- --> <!-- Values: unsigned integer --> <!-- --> <!-- default = 10 --> <param name="MaxHistoryDepth">10</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxAutofindSequence --> <!-- --> <!-- The maximum number of "autofind" sequences to be issues --> <!-- before stopping. An autofind sequence consists of a --> <!-- find followed by an assign followed by an appropriate --> <!-- repeat of the original transaction (update,bedchk, etc.) --> <!-- Note that this is affected by MaxHistoryDepth, in that --> <!-- MaxHistoryDepth counts EVERY individual transaction and --> <!-- could cause stopping before MaxAutofindSequence is --> <!-- exhausted. --> <!-- --> <!-- Values: unsigned integer --> <!-- --> <!-- default = 1 --> <param name="MaxAutofindSequence">1</param> <!-- Section: ESL Manager --> <!-- -->
Appendix B: DecisioNet Configuration Files B-35 <!-- MaxPricecheckCorrectiveDepth --> <!-- --> <!-- The maximum number of pricecheck/corrective action tasks --> <!-- to process before stopping. Price checks and corrective --> <!-- actions on sumchecks are related, in that one can --> <!-- eventually cause the other. --> <!-- Note that this is affected by MaxHistoryDepth, in that --> <!-- MaxHistoryDepth counts EVERY individual transaction and --> <!-- could cause stopping before this parameter is exhausted. --> <!-- --> <!-- Values: unsigned integer --> <!-- --> <!-- default = 3 --> <param name="MaxPricecheckCorrectiveDepth">3</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxTransactionRecordBlock --> <!-- --> <!-- The maximum record block size for Transaction record --> <!-- sets. The larger the number, the greater the memory --> <!-- usage, but the faster the processing. --> <!-- --> <!-- Values: unsigned integer --> <!-- --> <!-- default = 128 --> <param name="MaxTransactionRecordBlock">128</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxESLTransactionRecordBlock --> <!-- --> <!-- The maximum record block size for ESLTransaction record --> <!-- sets. The larger the number, the greater the memory --> <!-- usage, but the faster the processing. --> <!-- --> <!-- Values: unsigned integer --> <!-- --> <!-- default = 128 --> <param name="MaxESLTransactionRecordBlock">128</param> <!-- Section: ESL Manager --> <!-- -->
B-36 Appendix B: DecisioNet Configuration Files <!-- MaxTransactionRecordBlock --> <!-- --> <!-- The maximum record block size for ESL record --> <!-- sets. The larger the number, the greater the memory --> <!-- usage, but the faster the processing. --> <!-- --> <!-- Values: unsigned integer --> <!-- --> <!-- default = 128 --> <param name="MaxESLRecordBlock">128</param> <!-- Section: ESL Manager --> <!-- --> <!-- MaxUpdateImageAgeBeforeRefresh --> <!-- --> <!-- When update requests are posted to the spool file, an --> <!-- update image is also posted to the update image file and --> <!-- represents the data obtained from the data reader. --> <!-- Since the update image can get out of date, this --> <!-- parameter gives the ability to specify how old an update --> <!-- image may get before the ESL Manager refreshes the --> <!-- update image with a fresh read from the data reader. A --> <!-- setting of all 0's forces the ESL Manager to request the --> <!-- data from the data reader each time the update is sent. --> <!-- --> <!-- Values: valid time period specification --> <!-- --> <!-- default = 7 days (P0Y0M7DT0H0M0S) --> <param name="MaxUpdateImageAgeBeforeRefresh">P0Y0M7DTH0M0S</param> <!-- Section: ESL Manager --> <!-- --> <!-- OperatingMode --> <!-- --> <!-- Mode the ESL Manager is operating in. --> <!-- --> <!-- Values: INSTALL or NORMAL --> <!-- --> <!-- default = NORMAL --> <!-- --> <!-- THIS PARAMETER IS MAINTAINED BY THE ESL MANAGER AND --> <!-- SHOULD NOT BE MODIFIED. --> <param name="OperatingMode">NORMAL</param> </section>
Appendix B: DecisioNet Configuration Files B-37 <!-- End ESL Manager Section --><!-- DecisioNet Console Section --><section name="DecisioNet Console"><!-- TraceFileName --><!-- TraceLevel --><!-- Specifies the trace log filename and the logging level. --><param name="TraceFileName">dnConsoleTrace.trc</param><param name="TraceLevel">0</param><!-- ForcePrintEnabled --><!-- GCA parameter --><!-- Valid Values = 0 1 --><!-- Default = 0 --> <param name="ForcePrintEnabled">0</param><!-- PrintOverlaysEnabled --><!-- Valid Values = 0 1 --><!-- Default = 0 --><!-- controls whether the system provides the capability to --><!-- print overlays or reprint overlays --> <param name="PrintOverlaysEnabled">1</param><!-- PriceLevel --><!-- Valid Values = 0 1 --><!-- Default = 0 --><!-- controls whether the system provides input fields for --><!-- price level at the Link/Modify/Unlink screens --> <param name="PriceLevel">0</param><!-- PriceUnit --><!-- Valid Values = 0 1 --><!-- Default = 1 --><!-- controls whether the system provides field for --><!-- unit at the Link/Modify/Unlink screens --> <param name="ProductUnit">1</param><!-- ESLDefaultToProduct --><!-- Valid Values = 0 1 --><!-- Default = 1 --><!-- controls whether the which field recieves input focus --><!-- Product Number or Serial Number on the -->
B-38 Appendix B: DecisioNet Configuration Files<!-- Link/Modify/Unlink screens --> <param name="ESLDefaultToProduct">1</param> <!-- Report Sub Section --> <!-- After changing the SQL statement, please ensure to chg. --> <!-- displayed column headings in the verbage xml file too. --><!-- ReportSQL1 --><!-- SQL query to generate the report --> <param name="ReportSQL1">select DATE_FORMAT(esl.LASTNORESPONSE,"%Y/%m/%d%H:%i"), item.item_desc, HEX(esl.SERIAL_NUMBER),location_description.location_name, esl.LINK_ID, esl.LINK_SUB_ID,DATE_FORMAT(esl.LASTACKTIME,"%Y/%m/%d %H:%i"),ELT(FIELD(esl.UNRESPONSIVE_FLAG,"1","0"),"UNRESPONSIVE","COMMUNICATING") from location_description, esl, item WHERE location_description.location_id = esl.esl_location_id AND esl.UNRESPONSIVE_FLAG = "1" AND item.item_id = esl.link_id AND item.item_sub_id = esl.link_sub_id</param><!-- ReportSQL1SelectColumn --><!-- Valid Values = 0 1 --><!-- Default = 0 --><!-- controls whether the checkbox is present in the first --><!-- column of the report --> <param name="ReportSQL1SelectColumn">1</param> <!-- ReportSQL1KeyColumn --> <!-- Valid Values = 0 .. nbr of columns in SQL query - 1 --> <param name="ReportSQL1KeyColumn">3</param> <!-- ReportSQL1Button --> <!-- Valid Values = 0 1 --> <!-- Default = 0 --> <!-- controls whether there is a button in addition to the --> <!-- 'Cancel' button on the screen --> <param name="ReportSQL1Button">1</param><!-- ReportSQL2 --><!-- SQL query to generate the report --> <param name="ReportSQL2">selectDATE_FORMAT(spool_log.record_complete_date,"%Y/%m/%d %H:%i"),DATE_FORMAT(spool_log.start_date,"%Y/%m/%d %H:%i"), item.item_desc,
Appendix B: DecisioNet Configuration Files B-39HEX(spool_log.SERIAL_NUMBER), location_description.location_name,spool_log.LINK_ID, spool_log.LINK_SUB_ID,ELT(spool_log.record_type,"UPDATE","BEDCHECK","VERIFY","FIND","ASSIGN","SEARCH"), HEX(spool_log.record_Status + 1) from location_description, spool_log, item, esl WHERE esl.serial_number = spool_log.serial_number AND location_description.location_id = esl.esl_location_id AND item.item_id = spool_log.link_id AND item.item_sub_id = spool_log.link_sub_id AND spool_log.record_status < 0</param><!-- ReportSQL2SelectColumn --><!-- Valid Values = 0 1 --><!-- Default = 0 --><!-- controls whether the checkbox is present in the first --><!-- column of the report --> <param name="ReportSQL2SelectColumn">1</param> <!-- ReportSQL2KeyColumn --> <!-- Valid Values = 0 .. nbr of columns in SQL query - 1 --> <param name="ReportSQL2KeyColumn">4</param> <!-- ReportSQL2Button --> <!-- Valid Values = 0 1 --> <!-- Default = 0 --> <!-- controls whether there is a button in addition to the --> <!-- 'Cancel' button on the screen --> <param name="ReportSQL2Button">1</param><!-- ReportSQL3 --><!-- SQL query to generate the report --> <param name="ReportSQL3">select DATE_FORMAT(esl.LASTNORESPONSE,"%Y/%m/%d%H:%i"), item.item_desc, HEX(esl.SERIAL_NUMBER),esl_type_description.esl_type_name, location_description.location_name,esl.PREV_LINK_ID, esl.PREV_LINK_SUB_ID, DATE_FORMAT(esl.LASTACKTIME,"%Y/%m/%d%H:%i"),ELT(FIELD(esl.UNRESPONSIVE_FLAG,"1","0"),"UNRESPONSIVE","COMMUNICATING") from location_description, esl, item, esl_type_description WHERE location_description.location_id = esl.esl_location_id AND esl.Link_type_id = 0 AND item.item_id = esl.prev_link_id AND item.item_sub_id = esl.prev_link_sub_id AND esl.serial_number > esl_type_description.esl_type_low_serial AND esl.serial_number <esl_type_description.esl_type_high_serial</param>
B-40 Appendix B: DecisioNet Configuration Files<!-- ReportSQL1SelectColumn --><!-- Valid Values = 0 1 --><!-- Default = 0 --><!-- controls whether the checkbox is present in the first --><!-- column of the report --> <param name="ReportSQL3SelectColumn">0</param> <!-- ReportSQL3KeyColumn --> <!-- Valid Values = 0 .. nbr of columns in SQL query - 1 --> <param name="ReportSQL3KeyColumn">2</param> <!-- ReportSQL3Button --> <!-- Valid Values = 0 1 --> <!-- Default = 0 --> <!-- controls whether there is a button in addition to the --> <!-- 'Cancel' button on the screen --> <param name="ReportSQL3Button">0</param><!-- ReportSQL4 --><!-- SQL query to generate the report --> <param name="ReportSQL4">selectDATE_FORMAT(spool_log.record_complete_date,"%Y/%m/%d %H:%i"),DATE_FORMAT(spool_log.start_date,"%Y/%m/%d %H:%i"), item.item_desc,HEX(spool_log.SERIAL_NUMBER), location_description.location_name,spool_log.LINK_ID, spool_log.LINK_SUB_ID,ELT(spool_log.record_type,"UPDATE","BEDCHECK","VERIFY","FIND","ASSIGN","SEARCH"), ELT((spool_log.record_Status + 1),"SUCCESS","IN PROGRESS","PENDING") from location_description, spool_log, item, esl WHERE esl.serial_number = spool_log.serial_number AND location_description.location_id = esl.esl_location_id AND item.item_id = spool_log.link_id AND item.item_sub_id = spool_log.link_sub_id AND spool_log.record_status = 0</param><!-- ReportSQL4SelectColumn --><!-- Valid Values = 0 1 --><!-- Default = 0 --><!-- controls whether the checkbox is present in the first --><!-- column of the report --> <param name="ReportSQL4SelectColumn">0</param> <!-- ReportSQL4KeyColumn --> <!-- Valid Values = 0 .. nbr of columns in SQL query - 1 -->
Appendix B: DecisioNet Configuration Files B-41 <param name="ReportSQL4KeyColumn">3</param> <!-- ReportSQL4Button --> <!-- Valid Values = 0 1 --> <!-- Default = 0 --> <!-- controls whether there is a button in addition to the --> <!-- 'Cancel' button on the screen --> <param name="ReportSQL4Button">0</param><!-- ReportSQL5 --><!-- SQL query to generate the report --> <param name="ReportSQL5">selectDATE_FORMAT(spool_log.record_complete_date,"%Y/%m/%d %H:%i"),DATE_FORMAT(spool_log.start_date,"%Y/%m/%d %H:%i"), item.item_desc,HEX(spool_log.SERIAL_NUMBER), location_description.location_name,spool_log.LINK_ID, spool_log.LINK_SUB_ID,ELT(spool_log.record_type,"UPDATE","BEDCHECK","VERIFY","FIND","ASSIGN","SEARCH"), ELT((spool_log.record_Status + 1),"SUCCESS","IN PROGRESS","PENDING") from location_description, spool_log, item, esl WHERE esl.serial_number = spool_log.serial_number AND location_description.location_id = esl.esl_location_id AND item.item_id = spool_log.link_id AND item.item_sub_id = spool_log.link_sub_id AND spool_log.record_status > 0</param><!-- ReportSQL5SelectColumn --><!-- Valid Values = 0 1 --><!-- Default = 0 --><!-- controls whether the checkbox is present in the first --><!-- column of the report --> <param name="ReportSQL5SelectColumn">0</param> <!-- ReportSQL5KeyColumn --> <!-- Valid Values = 0 .. nbr of columns in SQL query - 1 --> <param name="ReportSQL5KeyColumn">3</param> <!-- ReportSQL5Button --> <!-- Valid Values = 0 1 --> <!-- Default = 0 --> <!-- controls whether there is a button in addition to the --> <!-- 'Cancel' button on the screen --> <param name="ReportSQL5Button">0</param>
B-42 Appendix B: DecisioNet Configuration Files</section><!-- End DecisioNet Console Section --> <!-- Data Reader Configuration Parameters --> <section name="Data Reader"> <!-- Number of digits after the decimal postion for the --> <!-- unit price field. --> <!-- Valid Values: 0, 2, 3 --> <param name="PriceDecimalPosition">2</param> <!-- Number of digits after the decimal postion for the --> <!-- price field. --> <!-- Valid Values: 0, 2, 3 --> <param name="UnitPriceDecimalPosition">2</param> <!-- Name of the debug file. This will be created in --> <!-- DecisioNet data directory. --> <param name="DebugFilename">DataReaderServer.log</param> <!-- Debug level --> <!-- 0 - None --> <!-- 1 - Errors --> <!-- 2 - Function Entry Points --> <!-- 3 - Messaging Trace --> <!-- 4 - Full Trace --> <param name="DebugLevel">2</param> <!-- What should the tag display when prices are < 1.00?--> <!-- Valid Values: CentSign, LeadingZero, NoLeadingZero --> <!-- For instance, if the price is .90 in the U.S. --> <!-- CentSign would display 90c where c is the cent sign--> <!-- LeadingZero would display 0.90 --> <!-- NoLeadingZero would display .90 --> <param name="PriceLessThanDollar">CentSign</param> <!-- What should the tag display when unit prices are --> <!-- less than < 1.00? --> <!-- Valid Values: CentSign, LeadingZero, NoLeadingZero --> <!-- For instance, if the unit price is .90 in the U.S. --> <!-- CentSign would display 90.0c where c is the cent --> <!-- sign. --> <!-- LeadingZero would display 0.90 --> <!-- NoLeadingZero would display .90 --> <param name="UnitPriceLessThanDollar">LeadingZero</param> <!-- What is the character used for a decimal separator --> <!-- Valid Values: Comma, Period --> <param name="DecimalSymbol">Comma</param> <!-- What king of rounding method should be used for -->
Appendix B: DecisioNet Configuration Files B-43 <!-- price and unit price. --> <!-- Valid Values: Normal, Up, Down --> <!-- For instance, the price or unit price is 3.555 --> <!-- Normal would display 3.56 --> <!-- Up would display 3.56 --> <!-- Down would display 3.55 --> <param name="RoundingType">Normal</param> </section></config>DecisioNet Task Manager Configuration file (taskman.cfg)## This is the configuration file for the DecisioNet 3.0 Task Manager.## FREQUENCY# specifies the number of MINUTES between each check of the# context directories for new or updated Task files.## Default if not specified is 1 minute.FREQUENCY=1# KILLINTERVAL# When Task Mgr. is requested to shut down, it first sends REQUESTS# to all the apps. to close themselves. If after a while the apps# still have not closed themselves, TM kills them with an NT# "TerminateProcess()". KILLINTERVAL specifies how many seconds to wait# between asking the apps to close themselves and killing the remaining# alive apps.## Default if not specified is 15 seconds.KILLINTERVAL=15# DEADCHECK# specifies the number of seconds between each time TM checks to see# if any tasks have died. This is needed because currently TM uses# a polling method to determine if tasks have died. Normally, in NT# a "WaitForMultipleObjects()" would be executed on the process handles# of all the tasks, but that API can only handle a max of 64 handles. So# in order for TM to handle > 64 tasks, this method is used. The number# should be an even divisor of 60 (number of seconds in a minute), and if# it is not, TM will round it UP to the NEXT even divisor of 60.#
B-44 Appendix B: DecisioNet Configuration Files# Default if not specified is 5 seconds.DEADCHECK=3# EXCEPTION# Specifies a default exception handler for tasks which don't have one# defined to that task in the task file. Exception handlers are programs# which are run immediately if the main task dies and exits with a# non-zero status. The exception handler will be run with the following# args passed to it (in addition to whatever args are specified in the# config file):## <exception hldr [any args]> <task exit code> <task #> <task cmd line>## Default is to NOT have a default exception handler## EXCEPTION=excphdlr.exe -v (for example only - no such program exists)# CONTEXT# Specifies a new context to Task Manager. The context name must be# unique and not have any whitespace in it. It MUST be followed by# a TFILES= keyword to specify where to get the task files for this# context.# TFILES# Specifies a path and a file mask for finding valid task files for# the preceeding context. If the path specified is not ABSOLUTE, ie.# it doesn't start with either a drive letter or a \, then the path# is relative from the DNET Data Directory (usually c:\DNET\data)## The mask specifies which files in that directory will be scanned for# task information. Each file can have information about one or more# tasks, and there can be multiple task files in the directory. Files# in the directory that do not match the mask are ignored.CONTEXT=DNETTFILES=dnet.tm\*.infCONTEXT=TASK_MANAGERTFILES=taskman.tm\*.infDecisioNet Host Bridge Configuration file(dnhostbridge.xml)<?xml version="1.0" standalone="yes"?><!DOCTYPE HostDataBridge SYSTEM "dnhostbridge.dtd"><HostDataBridge><General
Appendix B: DecisioNet Configuration Files B-45 DatabaseName="dnet" MaxRecordLength="4096" MaxFields="999" MaxFieldLen="256" Delimiter="," SleepTime="5" Verbose="No"></General> <FileDefinition TypeID="KVAT" FileName="KVATMOD" Description="Host Modification Data" Delimiter=","> <SendESLDataEnabled="No"LinkID_Offset="1"LinkID_StripCheckDigit="No"LinkID_ZeroFill="Yes"LinkID_Default=""LinkSubID_Offset="2"LinkSubID_StripCheckDigit="No"LinkSubID_ZeroFill="Yes"LinkSubID_Default=""LinkType = "1"></SendESLData> <UpdateLabelRecordEnabled="No"LinkID_Offset="1"LinkID_StripCheckDigit="No"LinkID_Default=""LinkID_ZeroFill="Yes"LinkSubID_Offset="2"LinkSubID_StripCheckDigit="No"LinkSubID_ZeroFill="Yes"LinkSubID_Default=""LinkType = "1"></UpdateLabelRecord> <RecordDefinitionTable="ITEM"Audit="Yes"><Field Offset="1" Name="ITEM_ID" Type="CHAR(24)" Default="" PrimaryKey="Yes" ZeroFill="No" Length="24" OverlayPrint="Yes" IsLinkID="Yes" Required="Yes"></Field><Field Offset="0"
B-46 Appendix B: DecisioNet Configuration Files Name="ITEM_SUB_ID" Type="CHAR(24)" Default="0" SecondaryKey="Yes" ZeroFill="No" Length="24" IsLinkSubID="Yes" OverlayPrint="No" Required="Yes"></Field><Field Offset="15" Name="PACKAGE_SIZE" Type="DECIMAL(10,4)" Default="1.00" OverlayPrint="Yes" IsPackageSize="Yes"></Field><Field Offset="0" Name="CONVERSION_FACTOR" Type="DECIMAL(10,4)" Default="1.00" OverlayPrint="Yes" IsMeasure="Yes"></Field><Field Offset="7" Name="UOM_ID" Type="INT" Default="" OverlayPrint="Yes" IsHex="Yes" IsUnitOfMeasure="Yes"></Field><Field Offset="4" Name="ITEM_DESC" Type="VARCHAR(50)" Default="" OverlayPrint="Yes" IsDescription="Yes"></Field><Field Offset="8" Name="UOM_DESC" Type="VARCHAR(50)" Default="" OverlayPrint="Yes" IsDescription="Yes"></Field></RecordDefinition></FileDefinition><FileDefinition TypeID="ITEM" FileName="ITEMMOD"
Appendix B: DecisioNet Configuration Files B-47 Description="Host Modification Data" Delimiter=","> <SendESLDataEnabled="No"LinkID_Offset="1"LinkID_StripCheckDigit="No"LinkID_ZeroFill="No"LinkID_Default=""LinkSubID_Offset="2"LinkSubID_StripCheckDigit="No"LinkSubID_ZeroFill="No"LinkSubID_Default=""LinkType = "1"></SendESLData> <UpdateLabelRecordEnabled="No"LinkID_Offset="1"LinkID_StripCheckDigit="No"LinkID_Default=""LinkID_ZeroFill="No"LinkSubID_Offset="2"LinkSubID_StripCheckDigit="No"LinkSubID_ZeroFill="No"LinkSubID_Default=""LinkType = "1"></UpdateLabelRecord> <RecordDefinitionTable="ITEM"Audit="Yes"><Field Offset="1" Name="ITEM_ID" Type="CHAR(24)" Default="" PrimaryKey="Yes" ZeroFill="No" Length="24" OverlayPrint="Yes" IsLinkID="Yes" Required="Yes"></Field><Field Offset="0" Name="ITEM_SUB_ID" Type="CHAR(24)" Default="0" SecondaryKey="Yes" ZeroFill="No" Length="24" IsLinkSubID="Yes" OverlayPrint="No" Required="Yes"></Field><Field
B-48 Appendix B: DecisioNet Configuration Files Offset="2" Name="PACKAGE_SIZE" Type="DECIMAL(10,4)" Default="1.00" OverlayPrint="Yes" IsPackageSize="Yes"></Field><Field Offset="4" Name="CONVERSION_FACTOR" Type="DECIMAL(10,4)" Default="1.00" OverlayPrint="Yes" IsMeasure="Yes"></Field><Field Offset="3" Name="UOM_ID" Type="INT" Default="" OverlayPrint="Yes" IsUnitOfMeasure="Yes"></Field><Field Offset="5" Name="ITEM_DESC" Type="VARCHAR(50)" Default="" OverlayPrint="Yes" IsDescription="Yes"></Field></RecordDefinition></FileDefinition><FileDefinition TypeID="PRICE" FileName="PRICEMOD" Description="Price Modification Data" Delimiter=","> <SendESLDataEnabled="Yes"LinkID_Offset="1"LinkID_StripCheckDigit="No"LinkID_ZeroFill="No"LinkID_Default=""LinkSubID_Offset="2"LinkSubID_StripCheckDigit="No"LinkSubID_ZeroFill="No"LinkSubID_Default=""LinkType = "1"></SendESLData> <UpdateLabelRecordEnabled="No"LinkID_Offset="1"LinkID_StripCheckDigit="No"LinkID_Default=""
Appendix B: DecisioNet Configuration Files B-49LinkID_ZeroFill="No"LinkSubID_Offset="2"LinkSubID_StripCheckDigit="No"LinkSubID_ZeroFill="No"LinkSubID_Default=""LinkType = "1"></UpdateLabelRecord> <RecordDefinitionTable="ITEM"Audit="Yes"><Field Offset="1" Name="ITEM_ID" Type="CHAR(24)" Default="" PrimaryKey="Yes" ZeroFill="No" Length="24" OverlayPrint="Yes" IsLinkID="Yes" Required="Yes"></Field><Field Offset="0" Name="ITEM_SUB_ID" Type="CHAR(24)" Default="0" SecondaryKey="Yes" ZeroFill="No" Length="24" IsLinkSubID="Yes" OverlayPrint="No" Required="Yes"></Field></RecordDefinition></FileDefinition><FileDefinition TypeID="ESL" FileName="PREEPLMOD" Description="PRE ESL Tag Modification Data" Delimiter=","> <SendESLDataEnabled="No"LinkID_Offset="2" LinkID_StripCheckDigit="No"LinkID_ZeroFill="No"LinkID_Default=""LinkSubID_Offset="2"LinkSubID_StripCheckDigit="Yes"LinkSubID_ZeroFill="No"LinkSubID_Default=""LinkType = "1"></SendESLData> <RecordDefinition
B-50 Appendix B: DecisioNet Configuration FilesTable="ESL"Audit="No"><Field Offset="2" Name="LINK_ID" Type="VARCHAR(24)" Default="0" ZeroFill="No" StripCheckDigit="No" Length="24"></Field><Field Offset="0" Name="LINK_SUB_ID" Type="VARCHAR(24)" Default="0" ZeroFill="No" StripCheckDigit="No" Length="24"></Field> <Field Offset="8" Name="SERIAL_NUMBER" Type="INT" Default="" PrimaryKey="Yes"></Field><Field Offset="6" Name="ESL_LOCATION_ID" Type="INT" Default="" IsLocation="Yes"></Field><Field Offset="0" Name="INSTALL_DATE" Type="DATETIME" Default="$(DATETIME)"></Field><Field Offset="0" Name="ORPHAN_FLAG" Type="ENUM" Default="F"></Field> </RecordDefinition></FileDefinition><FileDefinition TypeID="ESL" FileName="ESLMOD" Description="Front Back Tag Modification Data" Delimiter=","> <SendESLDataEnabled="No"LinkID_Offset="1"
Appendix B: DecisioNet Configuration Files B-51 LinkID_StripCheckDigit="No"LinkID_ZeroFill="No"LinkID_Default=""LinkSubID_Offset="0"LinkSubID_StripCheckDigit="Yes"LinkSubID_ZeroFill="No"LinkSubID_Default=""LinkType = "1"></SendESLData> <RecordDefinitionTable="ESL"Audit="No"> <Field Offset="1" Name="SERIAL_NUMBER" Type="INT" Default="" PrimaryKey="Yes"></Field><Field Offset="2" Name="LINK_ID" Type="VARCHAR(24)" Default="0" ZeroFill="No" StripCheckDigit="No" Length="24"></Field><Field Offset="0" Name="LINK_SUB_ID" Type="VARCHAR(24)" Default="0" ZeroFill="No" StripCheckDigit="No" Length="24"></Field> <Field Offset="0" Name="LINK_TYPE_ID" Type="SMALLINT" Default="1"></Field> </RecordDefinition></FileDefinition></HostDataBridge>
B-52 Appendix B: DecisioNet Configuration Files

Navigation menu