Raytheon IIS ARTU Air-Ground Radio System User Manual installation manual part four

Download:
Mirror Download [FCC.gov]
Document ID	257062
Application ID	9tHYc/qbknJFZXsfpy1m1A==
Document Description	installation manual part four
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	216.33kB (2704090 bits)
Date Submitted	2002-07-17 00:00:00
Date Available	2002-09-17 00:00:00
Creation Date	2002-07-01 16:17:20
Producing Software	Hewlett-Packard Intelligent Scanning Technology 3
Document Lastmod	2002-07-17 14:09:14
Document Title	installation manual part four
Document Author:	tjdrew [ TJDREW ]

FCC ill: CDG-ARTU
MAGNASTAR
EXHIBIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
7.1.2.5.4 SATCOM Terminal ro's
The following screen progressions show how to enter a terminal 10 number for SATCOM ground to air calling. The
procedure to enter a station or aircraft terminal 10 number are the same. A station terminal 10 number applies, or will ring,
only the associatedhandsetbeing programmed. An aircraft terminal 10 number applies, or will ring, all the handsetsin the
system. The screen progression also shows how to cancel a terminal 10 number. An aircraft terminal 10 is a system function
and need only be programmed from one handset.
Inplane
Aircall
Satcom
select
-->
To
>1
>2
->3
s.lect
-->
Disable
Call
Waiting
>4
Go Back >t
select
station
aircraft.
-->
Enter
terminal
ID.
or
Station
Terminal
ID
001
New:
Or
select
OK
cancel
if
required.
Go Back >t
Clear
>+
-->*
7.1.2.5.4.1 Disabling a Station From Ringing with a SA TCOM Aircraft TerminailD
It is possible to disable a number of individual handsetsor active ports from ringing when an aircraft terminallD number is
programmed in the system Each handsetor active port that is not to respondto an aircraft terminallD number must be
programmed as such. The following screenprogressionsshow the steps necessaryto cancel an aircraft terminallD response.
Inplane
Aircall
Satcom
Select
-->
To
Select
-->
Disable
Call
Waiting
select
-->
>1
>2
->3
>4
Select
Yes or
No for
aircraft
terminal
ID
response
Go Back >.
7-11
RevB
EXHIBITC
FCC ill: CDG-ARTU
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
7.1.2.5.5CaD Waiting
The following screenprogressions show bow to enable or disable the call waiting feature. Call waiting will alert the user of
an additional incoming call regardlessof its origin (inplane or ground initiated) while engagedin a telephone call.
Inplane>1
Aircall
>2
Satcom ->3
Select
-->
To Enable
Call
Waiting
>4
Go Back
>#
The call
display
keypress
Waiting
feature
may be toggled
enable
or disabled
by entering
of 4.
to
Warning:
The Enable or Disable shown on the
screen describe$
the $tate the system will
be
placed when a 4 is pressed.
The example
screen indicates
that call waiting
is
disabled.
7.1.2.5.6 Speed Dial
The following screenprogressions show how to enter speeddial numbers. The following items are to be entered. The three
digit speeddial number (*510 through *549), a phone number and a 10 character label. The label is an optional entry.
ect
for
Spe- ed
Sel*
Dia 1
Set -up
-Enter
dialing
sequence
Svc+Number
Select
5 to
delete
number
You
1+8882467
827
OK
>+
Clear
-->*
Go Back >t
Enter
the type
of service
(1= voice,
3= Fax,
4= Modem)
followed
by the
number to
be dialed.
Then enter
+ for OK.
-->
maY--
enter
a 10
character
label.
CUrsor ->*
OK/Next >+
OK/Main >1
Help --->0
dial
Enter
the three
digit
speed dial
number in the
510-549 range.
Then enter
+ for
OK.
-->
speed
dial
number
510-549
510
OK
>+
Clear
-->.
Main --->I
Select
to save
the speed
Enter a 10
character
label
for the entered
speed dial
number.
You may
ent' er a 10
cha racter
lab el.
entry
Star
Line
CUrsor
Select
0 to
view the help
screen
-->
7.1.2.5.7AIU Configuration
Enter
digit
->*
OK/Next >+
OK/Main >t
Help --->0
SATCOM
The fo)]owjng screenprogressionsshow the options available for configuring the AlU when used wjth an analog SATCOM
system. The AlU SATCOM features include two different impedance configurations and two possible interface modes of
operation. The two different impedanceconfigurations are High Impedance(WH-IO type) and Low impedance(600 ohm).
The two different modes of operation are Handset and PBX. The Handsetmode provides no feedback to the user on the LCD
display and operatesstrictly as a handset would. In the PBX mode the handsetprovides the user with feedback information
on the handsetLCD display providing the dialed number and ca)] progressinformation. This mode is only valid for those
SATCOM systemswhich support handsetPBX functions.
7-12
RevS
EXHIB IT C
FCC ID: CDG-ARTU
MAGNASTAR
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
configure
Select
for
AIU.
-->
Satcom
Select 1
for SAreOM
-->
-->1
Impedance
~~~~~~~i
Mode
Handset
>3
~---~>2
SatcODl /
GroundCell
Select-->3
Make the
appropriate
selection
to
match the
aircraft
configuration
The current
configuration
will
Go Back
Go Back
>1
>1
be
highlighted.
7.1.2.5.8 AIU Configuration OF Radio
The following screenprogressionsshow the options available for configuring the AIU when used for HF Radio or other
analog audio type interfaces. The AIU HF Radio function featuresthe ability to enable/disablethe voice operated (VOX)
push to talk (PTf) switch function. Disabling the PTf will automatically connect the handsetmicrophone to the AIU analog
audio output when the HF Radio (or other label name) option is selectedby the user. There are also two audio adjustments
that can be made from these screens. The Decay adjustment will vary the amount of time that the PTT will be kept active
after the analog input falls below the VOX threshold. The Senseadjustment will vary the sensitivity of the VOX PTf. All
three of these options are system functions and as such only need to be programmed from one handset. It is possible to
assign a label other than HF Radio. The HF Radio label is the system default label.
Passcode
Charige > 1
Charge
Direct
>2
Credit
>3
Phone I >4
Speed Dial
Setup ->*
Delete
>5
AIU
>6
More --->+
Main --->1
select
for AIU.
-->
confi~
Satcom
Select
for HP Radio
-->1
-->
HF Radio >2
Satcom /
GroundCell
Select-->3
Go Back >1
You may
The PTT enable
/disable
option
displays
what
result
will
be
progranuned when
* is pressed.
Select
+ to
change the HP
Radio label.
-->
enter
an 8
character
label.
HF
Cursor
OK
Help
Radio
->.*
>.
--->0
Enter
an
character
to modify
HF Radio
label
the
label.
Select
0 to view
the help screen.
--->
Press * to move
the cursor.
Press'
to enter
label.
Press '5'
to pick a
character
list.
Press '6'
or '4' to
move up ordown the
list.
Go Back >*
7.1.2.6 Maintenance Screen #2
The secondmaintenancescreenallows the wer to changethe station setup. to enable/disablethe handsetringer. to select the
dialing plan, select the system default link, select the station MODEM default baud rate and to enable/disableMODEM call
hand-offs.. The secondmaintenancescreenis shown below:
7~.3
RevB
FCC ill: CDG-ARTU
EXHIBIT C
MAGNASTAR C-2000 DIGITAL AI RBORNE TELEPHONE SYSTEM
Select
+ to reach
second maintenance
from the first.
--->
the
screen
7-14
RevB
EXHIBIT C
FCC 10: CDG-ARTU
MAGNASTAR
C-2000 DIGITAL AIRBORNE T
LEPHONESYSTEM
7.1.2.6.1 Station Setup
A MagnaStar digital handsetwhen connectedto the LAN is considered a station. It is possible to configure a handsetfor
different types of operation or station types. A Cabin station is the system default mode and is considered the normal
condition. A Cockpit station is the same as a Cabin station except for operation when the system Billing mode is configured
for credit card. If the system Billing mode is set for credit card use, then any handsetconfigured as a Cockpit station will bill
the aircraft account and not require the use of a credit card. There is no limit on the number of handsetsthat can be
configured as Cockpit stations.
A digital handsetcan also be configured as a FAX, Modem, TDD or PC station. These station types configure the use of the
RJ-II jack on the handset. Configuring a handsetas a Fax, Modem or TDD station has the following effect; when using the
RJ-II jack, the phone number can be directly dialed from the connected device mther than using the handsetkeypad Also,
becausethe device type or call type is identified, only the ten digit number needsto be dial (for domestic calls). When
configured as a PC station, any dialing activity on the RJ-II jack must be precededby a "3" or "4" prefix to identify the type
of opemtion; Fax (3) or Modem (4). Both functions can be used as long as the prefix identifies the type of opemtion. The
handsetdoes not have to be taken out of the bezel (or taken otThook) to be use when a handsethas been programmed as a
Fax, Modem, TDD or PC station. Only one digital handset in a system can be configured as a Fax, Modem, TDD or PC
station.
Stati on
Cock ~!,~~l
Select 1
to change
the
Station
Setup.
-->
Q.x
FAX
Select
the appropriate
the type of operation
~[c+"'"'>2
number
required.
for
>3
Mode
TDD
III
PC-
Go Back
-->4
>5
>6
The current
configuration
be highlighted.
mode will
>*
7.1.2.6.2 Select Aero-H or Aero-I SATCOM Service
A user may select the Aero-H SATCOM service, instead of Aero-l SATCOM service for FAX calls. If both servicesare
available (Aero-H+), SDUs (Satellite Data Units) manufactured by Collins and Honeywell default to Aero-l which supports
2400bps FAX calls. Aero-H supports 4800bps FAX calls. The higher rate SATCOM FAX mode may be enabled but should
be done only for Aero-H+ SATCOM installations otherwise the SDU will reject the FAX call setup.
Station
Setup ->1
To Disable
Ringer
>2
Dialing
Plan -->3
Link
--->4
Cana~ ~I
Mexico
Mexico
Select
-->
To
Ael
Sat
Dir:
Prf'
More --->+
Go Back >t
us/
.~
anable
Select
To Disable
:0- I/H+
:ca m
lli ng
Ifi x->3
Go Back
>2
!elect
Ae:( :-o-I/H+
Sa
Di~
Pr"
~com
tling
}fix->3
More --->+
Go Back >1
>t
7-15
RevB
EXHIB rr c
FCC ill: CDG-ARTU
MAGNASTAR
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
~..;;;-
The higher
-Enable-
rate
feature
or -Disable.
may be~tQgg1ed
to display
by entering
a keypress
of 1.
Warning:
The Enable or Disable
shown on the
screen describes
the state
the system will
be
placed
when 1 is pressed.
This screen
indicates
that
the higher
rate
PAX Aero-H+ Satcom dialing
prefix
is enabled.
7.1.1.6.3 Ringer Enable/Disable
~::,,'
A digital handsetand the associatedexternal call alerter switch outputs configured for that handsetcan be disabled.
The ringer
feature
may be toggled
-enableor -disableby entering
of 2.
to display
a keypress
Warning:
The Enable or Disable
shown on the
screen describes
the state
the system will
be
placed
when 2 is pressed.
This screen
indicated
that
the ringer
feature
is enabled.
The current
state
of the ringer
can always be
viewed with
the use of the information
screens
from the setup menu.
7.1.2.6.4 Dialing Plan
The C-2000 system can be configured for one of two possible dialing plans; United States& Canadaor Mexico. The system
is programmed not to require the user to enter dialed numbers in the international dialing format when placing calls to either
the US & Canadaor Mexico, dependenton the setting of the dialing plan. However, the international dialing format can
always be used. The appropriate dialing format must be identified to simplify dial operation. All numbers dialed outside the
identified dialing plan requires use of the international format. The dialing plan default value is US/Canada.
Se1 .ect
to change
thE t Dialing
Pl! ~n.
.>
uSj~na~
Mexico
>1
.>2
To Enable
Aero-I/H+
Satcom
Dialing
Prefix-»
Select
nwnber
dialing
the appropriate
for the required
plan.
The current
highlighted.
value
will
be
Go Back >t
7.1.2.6.5 Default Link and Auto Link Switch
7-16
RevB
EXHIBrrc
FCC ill: CDG-ARTU
MAGNASTAR C-2000
DIGITAL AIRBORNE
TELEPHONE
SYSTEM
For MagnaStar systemsthat are interfaced to a SATCOM unit, it is possible to configure each station to use either the GTE
Airfone ground network or the SATCOM satellite system as the default link. The default link is station programmable. The
MagnaStar system default is the GTE Airfone system (Air to Ground).
The MagnaStar system also provides the capability to automatically route calls between the GTE Airfone and the SATCOM
system, if the default link is being used to capacity, or is not available for use. This feature is called Auto Link Switching.
The Auto Link Switch feature is a system function and can be programmed from anyone handset.
Select
the
The current
highlighted.
Select
for Link
-->
Select
3 to
Link SWitch
appropriate
Default
Default
Link will
enable
feature.
or
Link
be
disable
the
If the Auto Link SWitch feature
enabled,
then -To Disablewill
on the screen.
If
feature
is disabled,
will
appear on the
Auto
is
appear
the Auto Link SWitch
then - To Enablescreen.
7.1.2.6.6 Service Availability and Call In Progress Indieaton
CAS (Call Alerter Switch) output switch 0 can be programmed to close to indicate when any or all of the following services
are available: Air-Ground, GroundCell, SATCOM. CAS oUtput switch 9 can be Progranunedto close to indicate when a
selectedhandset(s)or CDBR-2 port(s) have a call in progressthrough one of the available service links. NOTE: The t'In
Use" indicator on the Inplane Calling Menu indicates which handsetsor CDBR-2 ports are off-hook. If CAS output switches
9 and 0 are used as indicators they can IK>tbe usedto signal the user of an incoming call.
--CASO
service
Indicator:
Select
-->
Select
-->
Select
-->
Air and >1
GndCell
Satcom
Select
Number
Of Service.
Selection
Will be
Highlighted
7-17
>2
->3
More --->+
Go Qack >t
Rev 8
EXHlBITC
FCC ID: COG-ARTU
MAGNASTAR
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
~--
Select
-->
select
Enter
Select the de. ired inplane number
The inplane number will
then be
Highlighted.
No
-->
Go Back
>1
7.1.2..6.7 MODEM Settings
4800 bps and 9600 bps MODEM call bandoffs between ground stations can be independently enabled or disabled as a system
function (i.e. for the entire aircraft) from a maintenancemenu. 9600 bps MODEM call handoffs are enabled as the factory
default and 4800 bps MODEM calls handoffs are disabled as the factory default. Each handsetand CDBR-2 port may be
configured independently wjth a different default rate (4800 or 9600 bps). Note: Ground-Air MODEM eatls (i.e. upealls)
are Dot supported.
Select
the appropriate
number to choose the
station
baud rate and to
enable
or disable
handoffs
Select 5
for Modem
-->
CUrrent
selection
be highlighted.
will
7.1.2.6.8Handset Attributes
The remaining maintenancescreensare referred to as handsetattributes. These include gains settings, call alerter functions,
and LED settings. These screenare reachedby successivelypressing "+" for roore from the second maintenancescreen.
7.18
RevS

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2002:07:01 16:17:20Z
Modify Date                     : 2002:07:17 14:09:14-05:00
Page Count                      : 8
Producer                        : Hewlett-Packard Intelligent Scanning Technology.3
Author                          : tjdrew [ TJDREW ]
Creation Date                   : 2002:07:01 16:17:20Z
Mod Date                        : 2002:07:17 14:09:14-05:00
Metadata Date                   : 2002:07:17 14:09:14-05:00
Creator                         : tjdrew [ TJDREW ]
Has XFA                         : No

EXIF Metadata provided by EXIF.tools