Raytheon IIS ARTU Air-Ground Radio System User Manual installation manual part six
Raytheon Company Air-Ground Radio System installation manual part six
Contents
installation manual part six
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 257064 |
| Application ID | 9tHYc/qbknJFZXsfpy1m1A== |
| Document Description | installation manual part six |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 152.9kB (1911202 bits) |
| Date Submitted | 2002-07-17 00:00:00 |
| Date Available | 2002-09-17 00:00:00 |
| Creation Date | 2002-07-01 16:17:20 |
| Producing Software | Hewlett-Packard Intelligent Scanning Technology 3 |
| Document Lastmod | 2002-07-17 14:14:54 |
| Document Title | installation manual part six |
| Document Author: | tjdrew [ TJDREW ] |
EXHIBfi' C
FCC ID: CDG-ARTU
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
MagnaStar Aircraft Configuration Settings
Aircraft Tail Number
Date:
Svstem Confil!uration Settinl!s:
Maintenance
Pa88code:
Billing
Node:
Aircraft
Aircall
NUmber:
Direct
Call
pickup:
Terminal
ID:
Call
waiting:
Y/N
Satc~
I GroundCell
Bighl
Low
Band.et
I PBX
Bnabled/Di8ahled
Bnabled/Diabled
Bnab1ed/Di8ahled
US-Canada I Mexico
BDabled/Di8ab1ed
BDabled/Diabled
Air-Ground/Satc~/QrouDdCe11
0113456789
Voice/FAX/TDD
Y I N
Inplane
Number Assigned
Inplane
Label:
Station
Aircall
0 1 2 3 4 5 6 7 8 9
Hand..t
location:
Inplane
II'W8b8r A8.igne4a
0 1 2
Inplane
Label:
Station
Aircall
II'W8b8ra
Ring Handset -/Aircraft
Aircalla
Station
Numbera
pin:
Aircall
Station
Di .&bled
Ring Handset w/Aircraft
Linka Air-Oround/Satc~
Satc~
Station
Terainal
Y/R
Aircalla
IDa
--
Ring Handset w/Aircraft
Satc~
Term. ID:
Station
Type: Cockpit/Cabin/Pax/Mod../TDD/PC
Station
Baud Rate:
4800bp.
I 9600bp.
Hand.et
Ringera
BDabl84
I Di.abl84
Hand..t
Alerter
Gain:
Hand..t
RJ-ll
Hand..t
Handset
Hand..t
Hand..t
Hand..t
Hand..t
Coar..
pine
Voice
D'l'KP
DTNP
DTNP
TIN
Gaina
Speaker Gain a
Speaker Gaina
Sidetone
Gaina
Oain:
-IIoni tor Scale a
Moni tor Sen.e a
._-
---
Speed
Dial'
Speed Dial'
Speed
Dial'
T/R
LiDJr.: Air-Ground/
satc~
Satcom Station
Ter8dnal
%Da
Ring Handset -/Aircraft
Satc~
Te~.
%Da Y/R
Station
Type: Cockpit/Cabin/rax/~eaJTDD/PC
Station
Baud Rate:
6800bp.
/9600bp.
Hand..t
Ringer:
BDabled
/ Di8able4
Hand..t
Alert.r
Gain:
Hand..t RJ-11 Gaina
Hand..t
Coar..
Speaker
Gaina
Hand..t
Fine Speaker Gain:
~~ ~
Band..t
voice
sid.tone
Gaina
Hand..t D'rIIJ' Gain:
Hand..t
DTMF Noni tor Scale a
Band..t D'rIIJ' Noni tor Seu.e a
Hand..t
Coar..
Microphone
'1'X Gaina
Hand..t Coar.. Microphone Tx Gaina
Hand..t pine Microphone Tz Gaina -Auxiliary
Call Alerter:
012
3 4 567
Call In progre..
Indicator a ~l84/Di.abl84
Inplane LBD Blink Ratea
uplink LBO Blink Rate:
Speed Diu'
Speed D i a1
J 6 5 , 7 8 9
8Dabled/
Handset Confi2uration Settin2s:
location:
PIN:
Y/R
Node (AItJ):
Satcom ~edance
(AItJ):
Satcom Node (ArO):
Aero-I
Satcom Dialing:
Aero-B+ Satcom Dialing:
Auto Link Switchz
Dialing
Plan:
'800 MOD" Call
Randoff
Mode:
9600 MODBM Call Bandoff
Mode:
CAS Service
Indicator:
Auxilary
Call Alerter
Cadence:
PC Station
uplink
Call Mode:
Programm8d Speed Dial Humber8 z
HI' Decay Settingz
HI' Sen.e Setting:
HP Label:
HP P'1'T:
Hand..t
Card
pin
Satcom
I Credit
Aircall
Aircraft
Direct
!C:;i"
~~:
i~~c
::~"
c',...",,'
Hand..t
8 9
Fine Kicrophone '1'x Gaina
Auxiliary
Call Al.rter:
Call
In Progr...
Indicator
Inplane
LBD BliDJr. Rat.a
UpliDJr. LBD BliDJr. Rate:
012
3 6 5 , 7 8 9
a BDable4/Di8able4
FCC ill: COG-ARTU
EXHIBITC
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
MagnaStar Aircraft Configuration Settings
Aircraft Tail Number
Date:
Inplan.
Labela
Inplane
Y/R
Aircalla
T.rminal
ID:
Band..t
Band..t
D'l'KF ~ni
DTIIF ~ni
Bands.t
Coar..
Call
In
Inplan.
Uplink
Gaina
GaiDa
Indicatora
Rate:
Hand.et
Inplane
Inplane
Station
B\uaber Aa.igned I
Labell
Aircall
RU8b8r:
Station
Aircall
--
Pinl
0123'5678.9
Hand.et
Alerter
RJ-ll
aain
Hand.et
voice
Hand.et
Hand.et
Hand.et
DTIII'
DTIII'
DTIII'
--
Hand.et
Coar.e
Call
In
Inplane
Uplink
2C~
Scalel
Sen.el
Alerter:
TX Gain I
Indicator:
Rate:
Rate:
0 1 2 3 , 5 , 7 B,
GaiDI
Microphone
Progre..
LED Blink
LED Blink
Gain:
TX
Call
aain:
Monitor
Moni tor
Microphone
Hand.et
Auxiliary
Sidetone
BDabled/Di.abled
Coar.e
Speaker
Gain:
Fine
Speaker
Gain:
voice
Sidetone
Gain:
DTIIP
Gain:
DTIIP
Honi tor
Scale:
DTIIP
Honi tor
Senae:
Hand.et
Hand.et
Coar.e
Microphone
Tx Gain:
pine Kicrophone
Tx Gain: --
7 8 t
location:
NUmber Aa.ignedl
Inplane
Label:
~_.,
.'
---
0 1 2 3 4 5 I 7 8 ,
BDabled/Di.abled
0 ~ 2 J '5
, 7 . 9
Aircalll
Ter8dnal
ID:
Y/R
Ring Band..t
_/Aircraft
Satcoa T.:m.
ID:
Station
Typ.1 Cockpit/Cabin/Fax/Modem/TDD/PC
Station
Baud Rat.1
4.00bp.
/ 9600bp.
BaDd..t
Ring.r:
Bnabled
/ Di.abled
Band..t
Al.rt.r
Gain I
Hand..t
RJ-ll
Hand..t
Hand..t
Coar..
Speaker Gainl
Fin.
Speak.r
Gain I
Band..t
Voice
Sid.tone
Band..t
Hand..t
Hand..t
I)'1'Np
DTKr
Gain:
~nitor
Moni tor
Band..t
BaDd..t
Auxiliary
Call
In
Inplan.
T/R
Gain:
Band..t
Inplan.
Satcom Station
TIN
Gain:
Coar.e Speaker Gain:
Fine Speaker (Jainl
Fine
Hand.et
Hand.et
Hand.et
RJ-ll
Hand.et
Hand.et
Hand.et
Handset
Hand.et
Hand.et
Station
Aircall
-.her:
Station
Aircall
pilla
Ring Hand..t
-/Aircraft
Link:
Air-Qround/Satc~
Ring Hand.et
-/Aircraft
Aircalll
T/B
Linkl
Air-around/8at~
Satc08 Station
Ter8dnal
ZDI
Ring Hand.et
-/Aircraft
Satcam T8~.
ID:
Station
Type: Cockpit/Cabin/Pax/Nodea/TDD/PC
Station
Baud Ratel
tBOObp.
/ ,'OObp.
Hand.et
Ringer:
BDabled
I Di.abled
Hand.et
Auxiliary
Call
Alerter:
Call
In progre..
Indicator:
Inplane
LBD Blink
Rate:
Uplink
LED Blink
Rate:
BDabled/Di.abled
Rat.:
location:
:;.,
Tx GaiDa --0 1 2 3 t 5 , 7 8 9
Microphone
LED Blink
::,.;~-;;-
Scal.
Sen..a
Al.rt..r:
progr.ss
LBD Blink
TIN
",-,.
tor
tor
Tx
Call
Microphone
Bands.t
Auxiliary
Sid.tone
DTIIF Gain:
FiD.
Band..t
ID:
Gain:
Speak.r
Coar..
Band..t
Ring
Bands.t
-/Aircraft
Satcom
T.rm.
Station
TYPe:
Cockpit/Cabin/Fax/Mod../TDD/PC
Station
Baud Rate:
t800bp.
I '600bp.
Band..t
Ring.r:
Bnabled
I Di.abled
Band..t
Alert.r
Gain:
Band..t RJ-ll
Gain:
Band..t
Fin.
Speak.r
Gain a
Voice
0 1 2 3 4 5 I
Inplane
Label:
Station
Aircall
Ru8b8r:_Station
Aircall
pin:
-Ring
BaDd.et
-/Aircraft
Aircall:
T/R
Link:
Air-Ground/
Satcoa
Satcoa
Station
Ter8inal
ID:
Ring
Handset
_/Aircraft
Satcom
T8%m. ID:
Station
TYPe:
Cockpi t/Cabin/Pax/MOd../TDD/PC
Station
Baud Rate:
4800bp.
/ 'IOObp.
BaDd.et
Ringer:
BDabled
/ Di.abled
Hand.et
Alerter
Gain:
Station
Aircall
Rumb8r:
Station
Aircall
pina
Ring
Band.et
-/Aircraft
Link:
Air-QrouDdISatc~
Band..t
Aa.igDed:
0123~56789
A8.igneda
Sat com Station
Humber
location:
location:
IfUmb8r
BaDd.et
Band..t
Inplan.
Y/R
Gainl
Gainl
;i
..,
Scal.1
S.n..1
Coar.. Microphon. TX Gainl
pin. Microphone TX Gainl
Call Al.rt.r:
0 ~ 2 3 4 5 6 7 . 9
progr...
Indicator
I Bnabled/Di.abled
LBD Blink
Rat.1
Uplink LED Blink Rat.:
FCC ID: CDG-ARTU
Station
Aircall
R\l8ber1
Station
Aircall
pins
Ring Band.et
-/Aircraft
Aircalll
T/R
Link I Air-GrouDd/Satc~
Satcom Station
Terminal
ID:
Ring Band.et
-/Aircraft
Satcom Te~.
ID: T/R
Station
Type: Cockpit/Cabin/Fax/Nodea/TDD/PC
Station
Baud Ratel
j800bp.
l'fOObp.
Band..t
Ring.r:
8Dabled
I Diaabled
Band..t
Al.rt.r
Gain:
Band..t
RJ-ll
Gain I
Band..t
Coar..
Speak.r
~iD 1 Band..t
Fine Speak.r ~inl
~,,:
Band..t Voice sid.tone ~iDl
I'~
Band..t
D'1'IIF ~in:
Band..t
DTKF Monitor
Scal.:
Band..t
D'1'IIF Moni tor Sen..1
BaDd..t
Coar.. Microphone TX ~inl
Band..t
Fine Microphon. Tx ~inl
Auxiliary
Call Al.rter:
0 1 2 3 j 5 f 7 8 ,
Call
In progr...
Indicator:
8Dabled/Di.abled
Inplane
LBD Blink
Ratel
--
Uplink
LED Blink
Rat.:
Band..t
location:
Inplane
Inplane
Number
Labela
~-
Station
Aircall
RU8b8ra
A..igne4a
Aircalla
y,.
-"
RJ-ll
Gain a
Coar.. Speaker
Gaina
pine Speak.r Gaina
Ban4..t
BaDd..t
Voice
Sid.ton.
D'1'IIF Gain:
Band..t
D'1'IIF Koni tor
DTKF Koni tor
BaDd..t
Band..t
Gaina
Coar.. Microphone '1'z GaiDa
Pine Microphon. '1'z Gaina ---
Rat.a
Blink
~D
:":';;;:ii
'0'
Scale:
Sen..:
BaDd..t
Auxiliary
Call Al.rtera
Call
Xn Progr...
Indicator:
Inplane LED Blink
Rate:
uplink
."~'j.-~c
Band..t
Band.et
riDe Speak.r Qain:
Voice Sid.ton.
Qainl
Band.et
D'1'IIF
Gain
Band..t
Band.et
D'1'IIF
DTKr
Monitor
Monitor
BaD4..t
Coar..
Auxiliary
Call
Scal.1
S8D8.1
Microphone
Call
In Progr...
Inplan8
LSD Blink
Uplink
LSD Blink
10.';'
~--
Al.rterl
Y I.
TX Gainl
--
0 1 2 3 6 5 6 7 8 9
Indicator:
Rate I
Rat.:
BDabled/Di.abled
location:
NwDber Aa.igD,ed1 0 1 2 J, & 5 I' 7 8 9
Inplane
Labell
Station
Aircall
.u.berl
Station
Aircall
Pinl
Ring Band.et
w/Aircra~t
Aircalll
T/R
Linkl
Air-GroW1d/Satc~
Satcom Station
TermiDal
IDI
Ring BaD4.et
w/Aircraft
Satc~~.
ID:
Station
TYPe: Cockpit/Cabin/raz/~~~/TDD/PC
Station
Baud Ratel
4800bp.
191'OObp.
Band.et
Ringer:
BDable4
I Di.able4
Band.et
Alerter
Gain:
-"
'cot'
Link a Ai r-Ground I Satc~
Satcom Station
TerBdnal
ID:
Ring BaDc!..t
-/Aircraft
Satc~
T.Em. XD: Y/S
Station
Type: Cockpi t/Cabin/Paz/Mod../TDD/PC
Station
Baud Rat.a
j800bp.
I'SOObp.
BaDc!..t
Ring.r:
BDablec!
I Di.ablec!
BaDd..t
Al.rt.r
Gain:
Ban4..t
BaDc!..t
BaD4..t
0 1 2 3 6 5 6 7 8 9
Inplane
Labell
Station
Aircall
RU8b8r1
Station
Aircall
pin:
Ring BaD4..t
w/Aircraft
Aircalll
Y/R
Link:
Air-GroUDd/Satc~
Satcom Station
T.rBdnal
ID:
Ring Band..t
w/Aircraft
Satc08 T8~.
ID:
Station
Type: Cockpit/Cabin/rax/Modea/TDD/PC
Station
Baud Ratel
4800bp.
19600bp.
BaD4..t
Ring.r I 8Dabled
1 Di.abled
Band..t
Alert.r
Gainl
BaDd.et
RJ-ll
Gainl
BaD4..t
Coar..
Speaker Qainl
Band.et
Inplane
0123456789
Station Aircall
pina
Ring BaDc!.et -/Aircraft
Number A8.ignedl
Gainl
Labell
location:
Inplane
TX
Inplane
BaD4..t
0123456789
Microphon.
location:
Rumber Aa.ignedl
Band..t
Band.et
Inplane
C-2000 DIGITAL AI RBORNE TELEPHONE SYSTEM
riDe
MAGNASTAR
EXHlBlTC
,"'C:
0 1 2 3 . 5 S 7 8 ,
8Dablec!/Di.ablec!
TIS
Band.et
RJ-ll
Band.et
Band.et
Coar.e
Speaker Gainl
Gain I -- Pine Speaker
Band.et
voice
Band.et
D'1'KF Gain I
Band.et
BaD4.et
Band.et
Band.et
Auxiliary
Call
In
Inplane
DTMF Monitor
Scale I
DTHF Moni tor Sen.el
Coar.e Kicropbone
TZ Gainl
pine Micropbone
TZ Gainl
Call Alerterl
0 1 2 3 4 5 I' 7 8 9
Progre..
Indicator:
BDable4/Di.abled
LSD Blink
Ratel
Uplink
Gainl
sidetone
Gainl
--"
---
---
LSD Blink
Rate:
EXHIBrrc
FCC ID: CDG-ARTU
MAGNASTAR
8.0
C-2000 DIGITAL AIRBORNE TELEPHONE
SYSTEM
MMT SOFTWARE LOADING
This section covers loading of MMT software onto the MMT host computer.
The host computer must be a 386 or faster IBM compatible computer with 4 Megabytes of RAM.
a 3.5" high density floppy drive. and at least 1 Megabyte of memory available for use on the hard
drive. For the MMT software to run property it is important that the C: partition is no larger than
1.5 Gigabytes and be designated FAT or FAT 16. The MMT software must be executed from
DOS and cannot be run from Windows or a Windows DOS shell. A RS-232C serial port and
serial cable (PIN 422632-801) are necessary for connection to the MagnaStar C-2000 system.
Execution of the MagnaStar Maintenance Terminal (MMT) software can only occur after it is
loaded in the host computer memory. This loading process will only be required to be performed
the first time the MMT software is to be used or if an updated version is required. The host
computer when loaded with the MagnaStar Maintenance Terminal software will be referred to as
the MMT. Loading of the MMT software will automatically start the execution of the MMT after
the completion of the software download to the computer's memory. The following steps are to
be used if the MMT software has not been loaded into the host computers memory or if an
updated version is to be loaded:
Power up the computerand wait for the computerto completethe bootprocess.After
the computer has completed the boot sequence, insert the 3.5- MagnaStar Maintenance
Terminal (MMT) software disk in the appropriate drive (A or B) of the computer.
If you placed the diskette in the A drive use the following commands: From the root
directory type "A:\MMT COPY" . then press "ENTER" to execute this command.
C:>A:\MMT COpy IENTERI
If you placed the diskette in the B drive use the following commands: From the root
directory type "B:\MMT COpy B" , then press"ENTER"to executethis command.
C:>B:\MMT COpy B I ENTERI
The "MMT COPY" command will automatically load all the software files and create the
necessary directories required to operate the MMT software. This command will also
start the execution of the MMT software.
8-
RevB
9-i
Menu
Menu
"".."
""'
Menu
Configuration
Installation/Test
Menu
Boot
Radio
Radio
'."..".'."'
Operations
Menu
MMT
MMT
MMT
"""
Menu
BIT
Menu.
C-2000
C-2(xx)
C-2(xx)
Test
Menu
Maintenance
Debug
"""""""""."""..""
STATION
""
""""""'"
PASSCODE
GENSTARGROUND
""""'.".""'.'
CONCLUSION
Informatio.
ACCESS
Verification
USING
STATE
.""'
Tests
Check
ONLINE
OFF-LINE
ARTU
SYSTEM
MOUNTING
TRANSMI1TER
RECEIVE
COMMUNICATION
POWER
SIGNAL
OPERATIONAL
MEASUREMENT
POWER
TEST
SOFTWARE
VERIFICATION
FAN
STRENGTH
UP
OUTPUT
STATE
TRAY
TEST
Test
Mode
Mode
Mode
Commanded
Check
Troubleshoot
Pull
Log
Communication
Mode
RF
MAINTENANCE
TROUBLESHOOT
Interference
LAN
Handset
MEASUREMENT
Test
-EI
MAGNASTAR
Radio
MMTI
Cable
Counter
C-2000
MMT
START
LOCKED
ARTU
ARTU
ARTU
MMT
MMT
MMT
MMT
MMT
C-2000
Meuages
Commanded
UNLOCKED
RSS
MMTI
Commanded
Commanded
RESET
Data
Fault
Flight
L-Band
CEPT
9.1.1
9.1.2
9.1.3
9.1.4
9.1.5
9.1.6
9.1.7
HANDSET
Commanded
C-2000
C-2(xx)
C-2(xx)
C-2(xx)
Text
MMTI
MMTI
9.1.9
9.1.10
9.1.11
9.1.12
9.2.1
9.2.2
9.2.3
9.2.4
MMTI
9.2.5
Additioul
9.1.8
MMTI
9.3.3.4.1
9.3.3.1
9.3.3.2
9.3.3.3
9.3.3.4
9.3.1
9.3.2
9.3.3
9.1
9.3
HaDdIet
9.4
FCC ID: CDG-ARTU
EXHIBIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
EQUIPMENT TROUBLESHOOTING PROCEDURES
9.0 EQUIPMENT TROUBLESHOOTING PROCEDURES
,..
9.1 TROUBLESHOOTING PROCEDUREFOR MMT INSTALLA TION TUTORIAL
"""""""".'.."""""""'"
...9-1
...9-1
...9-1
9-2
...9-3
...9-5
...9-6
...9-9
...9-7
.9-11
.9-13
.9-12
.9-14
.9-16
.9-15
.9-16
.9-17
.9-17
.9-18
.9-18
.9-20
.9-22
.9-23
.9-26
.9-27
9-27
9-29
.9-30
9-30
9-32
RevS
FCC ID: CDG-ARTU
MAGNAST AR
EXHIBIT C
C-2000 DIGITAL AIRBORNE
TELEPHONE
SYSTEM
9.1.2 MMT COMMUNICATION
VERIFICATION
The MMT Communications Verification test assures that the MMT software is properly communicating
with the ARTU by checking the version of software that is loaded in the ARTU.
Symptom: "ERROR=>MMT communications
failure timed out"
The ARTU and the MMT are not communicating when this information is displayed in the Radio
Responseswindow. Check the MMT cable connection between the MMT computer and the
ARTU. Check for a damagedconnector on RS-232 serial communications port of the computer.
After checking these interface connections press "R" to repeat the test. If the same error is
displayed. cycle power on the computer. If the same error messageis displayed after cycling
power on the computer then replace the ARTU.
Symptom: "Radio software executing in unlocked online state"
This messagewill be displayed on the screenif the ARTU was powered up before the computer
with the MMT software running was connectedto the ARTU. Remove power to the ARTU for
greater than 20 seconds. Apply power to the ARTU and press "R" to repeat the test.
V..OA
MNT
R6dio
Re8PQna
Power-up Status:
80376 Kicroproc...or
ARTC code pile ARTCC40B.HBXVer
DBP code Pile MDSPC.OB.HEXVer
BIT code Pile MBITC.OA.HBX Ver
Boot code Pile ~31C.HBX
Ver
R6dio software is not executing.
'DSlA103
01, BRAN OK.
0.0 net. 0./06/00
0.0 Dat. 03/27/00
0.0 net. 05/18/99
0.0 Date 0./2./96
Bank
B8Dk
Bank
B8Dk
CRC:4CB8:
cac:1298:
CRC:209C:
CRC:B818:
~--~
MMT Tutorial
: Sy8ptom: "ERROR->MNTcO8mUnications failure
1.:25
12:13
16:03
14:27
- ti-.d
out."
to the AR'I'U.
a) Check that the MNT cable i. properly
connected
b) Pr..s
"R" to repeat test step.
c) If the error -ssage
still
appears, then cycle power on the coqlUter
and start
again.
d) If error -.sage
still
appears, turn power off to the AR'I'U for more:
than ten seconds. Apply ~r
to the AR'ro. Does the pault indicator
on
the front of the AR'I'U illuminate
for appr_~tely
one .!nut.
or 8Ore?
If it does, cbeck for a bad MNT cable or bad C(»I port on the c~ter.
e) If the fault
indicator
does not illuminate,
tben replace the ARTU.
(a.8tuzn
Figure 9.1.2. MMT Communications Verification MMTI Troubleshoot Screen.
9-2
RevB
FCC ID: CDG-ARTU
EXHIBIT C
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
9.1.3 START ARTU OPERATIONAL SOFTWARE
When the ARTU is powered up with an MMT connected,the ARTU software will not execute and will be
in what is termed a "boot" mode. When commandedby the MMT, the ARTU will start the operational
software. The first step in starting the operational is for the ARTU to run Built-In-Test (BIT). The normal
BIT processbegins by turning "ON" the ARTU Fault indicator. The MMT will indicate that the ARTU has
started software execution which is displayed in the Radio Responseswindow. The ARTU then begins an
FEPROM test which takes approximately 15-20 secondsto complete. Owing this time there will be no new
messagesdisplayed in the Radio Responseswindow. BIT test result information will be reported in the
Radio Responseswindow. Depending on how long the ARTU has been powered prior to executing powerup BIT, the screenmay pausein the middle of the tests. This pauseis to allow the ARTU oscillator to
warm-up. This can take one to five minutes. After this pause,BIT will complete.
Symptom: Radio Responseswindow does not display test results.
If the Radio Responseswindow does not appearto change,the user should look to seeif the red
Fault light is illuminated. If the red Fault light is not illuminated then press "R" to repeatthe test.
Symptom: ARTU fails power-up BIT.
If the ARTU fails a BIT test, note which test has failed and replace the ARTU.
After powerup BIT hascompleted,it is possibleto reviewthe BIT testdataby sendingthe
following MMT commands:
Press"FI ",
; scrollsscreento commanded
modemenus
press"2" andthenpressENTER, ; selectsRadioTestMenu
press"2" andthenpressENTER, ; selectsCommanded
Bit Menu
press"0" andthenpressENTER. ; selectsview BIT results
Pressing"N" for next,or "P" for previous,will scrollthe userthroughthe BIT testresults.
Symptom: ARTU appearsto pauseduring BIT for longer than ten minutes.
BIT will begin testing and stop during the middle of the tests to wait for the OCXO frequency
referenceto warm up. BIT testing will stop at the "QUERY AMX" test. Ifafter stopping at the
"QUERY AM)(" test, the MMT BIT test times out after ten minutes and the RED Fault indicator
is still illuminated, then the ARTU has faulted. Replacethe ARTU and note that the ARTU has
failed for OCXO warm up.
Symptom: BIT test appearsto repeat.
If the BIT test appearsto be repeating over and over then one of two conditions is occurring. One,
the voltage at the ARTU is dropping below +20.5 volts DC during the power up BIT. Measure the
voltage at the radio interface with ARTU attached. If the voltage drops below +20.5 VDC, check
the gauge of wire used for the power cable to insure that it is of sufficient size to minimize the
voltage drop from the circuit breaker to the ARTU. The secondcondition is current limiting. If
the power system cannot support a 3-5 amperecurrent surge while maintaining a stable voltage
then the ARTU will repeat BIT.
9-3
RevB
FCC 10: CDG-ARTU
EXHIBIT C
MAGNASTAR
C-2000 DIGITAL AIRBORNE
TELEPHONE
SYSTEM
V4. OA NNT Radio Response
: Power-up Statu8,
80376 Kicroproc...or
OK. SRAH ox.
ARTC code Pile ARTCC4OB.HIX Ver 0.0 Date 04/06/00
14,25
BaDk 1 CRC,~:
DSP code Pile KDSPC40A.HIX Ver 0.0 Date 03/27/00 12,13
BaDk 2 CRC,1298:
BIT code pile MBITC40A.HIX Ver 0.0 Date 05/18/99 16,03 BaDk 1 CRC,209C:
Boot code Pile ~31C.HBX
Ver 0.0 Date 04/24/'6
14,27 BaDk 1 CRC,B8& :
: Radio sottware is not executing.
V1A NNT Tutorial
: IJfS1A104
: This test step is info~tional
only.
: Pressing .C' will
start
Built-In-Test
(BIT). The no~l
BIT process begina
: by turning
.(»t. the ARro pault indicator.
The ~
will
indicate
in that the :
: AR'1'Ubaa started
sott~e
execution
which is displayed
in the Radio
: Respon... window. The AR'1'Uthen begins an PBPftCIf test which takes
: approximately
15-20 seconds. During this time there will
be no new ..ssages
: di8Played in the Radio Responses window. BIT test result
into~tion
will:
: be reported
in the Radio Responses window. Depending on how long the ARTU
: baa been powered prior
to executing power-up BIT. the screen may paU8e in
the
middle
_ra-up.
ot
the
tests.
This
paU8e
complete.
is
to
allow
This can take one to five IBinutes. After
the
ARTU 08cillator
to
this paU8e. BIT will
(R)eturn,
Responses
Radio
MMT
OA
V4.
Figure 9.l.3.A. Start ARTU Operational Software MMTI Troubleshoot Screen.
WAITDfG FOR POWER-UPBIT RESULTS «5 IIIMnE
Press 'B8c' to Terminate Wait
Radio software starting
execution.
The KIlT baa been reconfigured
for CON Port 1 at 9.6 kbs.
,'IR
S'.'O
DELAY:
,C',
: S~t_:
Radio ~SP0D8es window does not change.
al Did you W8~t for the PZPROMtest to cO8plete.
rete.t.
bl Did the ARro fault
light
: Sy8ptoa: ARro fails
power-up
al
Determine
KagnaStar
the Brr fault
Inatallation
information.
if
80 Pr88s "R" for,:,~
illlainate?
BIT.
and record
Manual
for
f'
;'
';;';;~
"};
cf
for repair
information.
steps
required
to view
See
fault
Replace faulted ARTU.
: Symptom: ARro appears to pause during Brr for l~ger
than ten ainutes.
al If the BIT testing
stops at the "TEST AKX" test step for longer than
ten ainute.
at rot~rature
then note that the ARTU baa failed
OCXO~-up.
Replace the failed ARTU.
(Rleturn:
Figure 9.1.3.8. Start ARTU Operational Software MMTI Troubleshoot Screen.
9-4
RevB
FCC 10: CDG-ARTU
EXHIBIT C
MAGNAST AR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
9.1.4 LOCKED OFF-LINE STATE
For the MMT to command certain tests for the installation checkout, the ARTU software must be placed in
a mode which will allow the ARTU the flexibility to perform these tests. This mode of operation is called
the "Locked OFF-Line State". This test step is a mode changeonly. Failure of this mode change will only
occur iftbe MMT is not communicating with the ARTU.
It should be noted that while the ARTU is in this mode, the Handset screenmay go blank and will not
respond to keypad inputs.
Symptom: ERROR=> MMT communications failure timed out.
If this messageis displaycd in thc Radio Responseswindow then check the cabling between thc
ARTU and the MMT. If the cabling is correct then press "R" to repeat the test.
V4.0A MMT Radio Re~
Radio 8oftw8re
executing
in locked
offline
VlA ~
:DlS1A1O6
,,
: Syq>toa: ERROR->I8rr c~icati0D8
a) Check the I8rr cable connecti_.
b) Press .R. for repeat.
state.
Tutorial'
failure
- tiJ
Figure9.].4. LockedOff-Line StateMMT] TroubleshootScreen.
9-5
RevB
~
FCC 10: CDG-ARTU
EXHIBIT C
MAGNASTAR
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
9.1.5 ARTU MOUNTING TRAY FAN TEST
Under normal operational conditions, the ARTU Mounting Tray Fan is activated by a switch in the ARTU
which is under software control. The ARTU monitors a temperature sensor located in the ARTU and is
programmed to turn on the Fan when the temperatureis at approximately room temperature. The ARTU
Mounting Tray Fan test will command the ARTU to turn the fan "ON" to check operation.
Symptom: The ARTU Mounting Tray Fan is not operational.
If the ARTU Mounting Tray Fan is not operational, the problem can be causedby the ARTU,
wiring to the ARTU Mounting Tray or the Mounting Tray Fan itself. Several steps wi)] be
required to detennine the causeof failure. These steps may also vary depending on which
assembly of the ARTU mounting Tray assembly that is used in the aircraft.
For -801 Tra~: Remove power from system Remove the power connector from ARTU J2
connector interface and ground pin P I-F of the ARTU Power cable. Apply power to the system.
If the fan operates,perform a continuity check on the ARTU Tray - ARTU Power cable interface.
If the wiring is correct, replace the ARTU. If the fan does not operate,replace the ARTU
Mounting Tray.
For -802Trax: Removethe PI connectorfrom the ARTU MountingTray. With powerremoved,
grotmdpin Jl-9 on the ARTU Tray. Apply powerto the system.If the fan doesnot operate,
replacethe ARTU MountingTray. If the fan operates,performa continuitycheckon the 802
ARTU Tray - ARTU Powercable. If the wiring is correct,replacetheARTU. Ifnot replace
cable.
V4.0A
C-2000 report8
engineering
teat
VlA
:IRS1A101
: SYJI4>tca: Pen do..
por -801 Tray:
8'l'
DOt operate.
~e
power
Radio
Response.
FAN CONTROLperformed
MNT Tutorial
from
syst_.
R~
J2
connector
fr..
ARTU end
ground pin Pl-P of the ARTU Power cable. Apply ~r
to the ayst_.
If
the fen operate8.
replace the ARTU. If the fan does not operate.
replace:
the
ARTU Mounting
Tray.
For -802 Tray: a..ove the Pl connector from the ARTU Mounting Tray. with
power r~ed.
gr~
pin Jl-'
on the ARTU Tray. Apply power to the
syst_.
If the fen ~
DOt operate.
replace the ARTU Mounting Tray. If
the fan operatH.
perfora . continuity
on the 802 ARTU Tray - ARTU
Power cable. If the continuity
is correct.
replace the ARTU. If not
replacecable.
Figure 9.1.5. ARTU Mounting Tray Fan MMTI Troubleshoot Scret
9-6
RevB
FCC 10: CDG-ARTU
EXHIBIT C
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
9.1.6 ARTU TRANSMITTER OUTPUT POWER
During the ARTU Transmitter Output Power test, the ARTU will transmit a CW signal at a frequency of
894.9495 MHz. The power level transmitted by the ARTU will be 10 watts minimum. Measurementof
the transmitted signal should be made as close to the Antenna as possible to check the functionality of the
greatestnumber of the C-2000 components. The insertion loss of components in addition to the ARTU
must be accounted for when measuring the output power of the C-2000 system. The maximum total cable
loss that can be used with the C-2000 system is specified at 3 dB. The maximum specified insertion loss of
the Duplexer is 1.4 dB. If power is measuredat the Antenna connector, the minimum power measured
should be no less than 4 watts.
It should be noted that the power meter or thru-line wattmeter used for this test must be capable of
withstanding 16 Watts of RF energy and must be capable of operating at frequency of I Ohz for correct
results.
Symptom: The MMTI appearsstuck.
Wait for the MMTI to properly execute commandsto ARTU (5-10 sec). Commandsto the ARTU
via the MMTI may take from 5 to 10 secondsto execute during which time the MMTI screenswill
appearto change and then stop before completing.
Symptom: Low output power / No output power.
If power measurementsat the Antenna connector are low, it will be necessaryto determine which
component is responsible for the excessiveloss by processof elimination. First, measurethe
output power directly out of the ARTU. If the power measurementis incorrect replace the ARTU.
If the power measurementis correct, measurethe output at the end of the transmit cable. If the
power measurementsis incorrect, replace the transmit cable. If the power measurementis correct,
measurethe power at the Antenna output of the Duplexer. If the power measurementis incorrect,
replace the Duplexer.
V.. OA MMT Radio Respons
'ing
teat
FAN CONTROLperfo~d.
::::::::::~ -~- ~~;w::::7J;~~
DfSlAl08
This
t..t
step
is
inatructional
only.
During the next test step the ARTU will
transmit
a CW signal at a power
level of +40 to +42 dBm. The Duplexer is specified
for a n8Xi.u.
loss
of 1.4 dB. The 8aXimu8 syat..
C8ble loas for the RP cables is specified
at 3 dB. The ~r
_ter
should measure greater
than +36 dBm when all
the above factors
are taken into account.
[aleturn
Figure 9.1.6.A. ARTU Transmitter Output Power MMTI Troubleshoot Screen.
,,"1
RevS
~
FCC ill: CDG-ARTU
EXHmrr C
MAGNAST AR
C-2000 DIGITAL AIRBORNE
~.~
+t
i C-2000
reports
eagiDeeriDQ
teat
TELEPHONE
MMT Radio R88p0D8"
INITIAL
PA ~
perfo~.
,DS1Al09
: ~t~:
Wait
SYSTEM
v4~
81'1 aR>ear. .tuck.
for
tha *1'I
to properly
.-cute
c~
to AR'fU (5-10 Me).
: ~t08:
Low output power / No output power.
H.-ure the output p~r
directly out of the AR'ro. If the power
me&8Ur..-Dti. incorrect replace the AR'ro. If the power8ea8Ur888Dti.
correct.
-=e
the output at the end of the tran~t
cable. If the
power _.ur-ts
is incorrect.
replace the tr~t
cable. If the ~
-..ur~t
i. correct.
_sure
the power at the Antenna output of the
Duplex8r.
If the power 88a8Ur8ment is incorrect.
replace the Duplexer.
.f
(R)eturn:
,,
..
Figure 9.1.6.8. ARTU Transmitter Output Power MMTI Troubleshoot Screen.
Vt.OA MItT Radio Resp0n8
C-2000
reporta
engineeriD9
teat
STOP
TRANSMIT
"~::.~
perfor8ed. ::i
,DlS1Al10
,,
: ~t_:
ARTU does not stop tran8lRitting.
If the ARTISdoes not stop transmitting
check that the ~
~.
properly
eonneeted. If the cable is properly
connected. pr..s
: repeat.
c"
-1
1.
"R- for
..
'1
Figure 9.1.6.C. ARTU Transmitter Output Power MMTI Troubleshoot Screen.
9-8
RevB
FCC ID: CDG-ARTU
EXHIBIT C
MAGNASTAR
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
9.1.7 ARTU RECEIVE SIGNAL STRENGTH MEASUREMENT
The ARTU Receive Signal Strength measurementtest will verify the complete RF portion of the C-2000
system. This test will require the use of a MagnaStar Loop-Around test box. During this test a 16 QAM
signal is transmitted by the ARTU. With the MagnaStar Loop-Around test box connectedto the Antenna,
the signal is coupled into the Loop-Around test box where it is mixed by 45 MHz and coupled back into the
Antenna. A receive signal strength measurementusing the ARTU checks out both the TSC and Pilot
receive channels of the ARTU as well all the componentsbetween the ARTU and the Antenna. The
frequency of the transmitted signal is 894.9495 MHz.
This test is to check for gross loss problems in the RF cables and associatedhardware and is not intended to
be a calibrated test measurement. Typically the value should be measuredat - 103 dBm +/- 6 dB with
nominally valued components. Becausethe TSC and Pilot channelsare separatereceivers, variations
between measurementsare possible. If, however, there is a delta between the two receivers of greater than
10 dB, the ARTU is to be rejected.
The Loop-Around test box is powered by a 9 volt battery. The battery voltage must be greater than 6.0
volts to operate and provide the expectedperfonnance results. The Loop-Around test box provides the
capability to check the battery to ensurethat the voltage is correct. The Loop-Around test box attenuator
setting should be set to the "ON" position for the first part of this test. Switching the attenuator to the
"OFF" position should changethe receive signal strength by approximately 30 dB.
Symptom: Reading between the TXRX and RX receivers greater than 10 dB.
If the delta between the TXRX (TSC) and RX (Pilot) receivers is greatertban 10 dB, repeatthe
test. If after repeating the test the sameresults occur then replace the ARTU.
Symptom: RSS readings on both the TXRX and RX channels less than -109 dBm (-103 dBm - 6 dB)
If the RSS readings are less than -109 dBm then the lossy component needsto be located. If the
ARTU Transmitter Output Power test has been successfully completed then the problem is either
the Antenna, Duplexer, Receive cable or ARTU. If the ARTU has successfully passedBIT, then
the most likely candidatesare the Antenna, Duplexer or the receive cable. With the proper
adapters,cable loss should be measuredfor the ARTU receive cable. Elimination of the receive
cable as the problem leavesthe Duplexer and Antenna. With the proper adaptersand a 30 dB/25
Watt pad, the antennacable can be directly attachedto the Loop-Around test box bypassing the
Antenna. If the loss problem still exists after bypassing the Antenna, replace the Duplexer.
'mS1A200
This
test
V4. OA 10ft' Radio
ReSPO8'8M
VlA
step
i8 instructional
IGrr TutorW;'
only.
In preparation
for measuring the syst..
receive 8ignal strength.
the
loop around test box -.t
be configured
and properly
placed for expected
results.
Perfora a battery
check prior
to use by turning
.ON. the loop
around test box and pressing
the -.ntary
battery
check _itch.
'ft1e
indicator
light
vill
illU8inate
if the battary
is within
operational
require8eDts.
set the attenuator
svitch
to the .ON. position.
Place the
cable clip-on
cla.p on the center of the blade antenna for best results.
II
,I
(a}~.-
Figure9. 7A. ARTU Receive Signal Strength MeasurementMMTI Troubleshoot Screen.
.2000 ~rta
V4.0A
.tatu.
update
MMTRadio Responses
ENABLED.
9-9
RevB
FCC ill: CDG-ARTU
MAGNASTAR
EXHIBIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
Pr'-'
F2 to View Status
Display
: SY8f{)tom, us Value alUch lower than ~kings
a) Are the ON/OFF and Attenuator
awitches
b)
c)
Tutorial
I8rr
:mSlA20l
VlA
on Loop-Around
in the correct
Is the battery
voltage
greater
than 6 volts?
.ove ~e
Loop-Around
Test Cable
connection
plac_t
Replace
cables
or C-2000 RP components one at a time
faulted
Teat Box.
po8ition?
on the
Ant~a.
to isolate
the
unit.
~t_,
RSS value difference
bet_en
the TXRX and RX is gre.ter
than 10 dB.
If values of the US readings bet_en
the TSC (TXRX) and the Pilot
(RX)
receivers
is greater than 10 dB replace the ARTU.
._"'~~:_:
Figure 9.1.7B. ARTU Receive Signal Strength MeasurementMMTI Troubleshoot Screen.
9-10
RevB
FCC 10: CDG-ARTU
EXHIBIT C
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
9.1.8 HANDSET I LAN TEST
The HandsetI LAN test wilt inform the installer of the number ofCDBRs/AIUs and Handsetswith which
the ARTU can cornrnunicate. This test does not distinguish the difference between a CDBR or an Am.
Also, this test will not identify the presenceof a CAS.
Symptom: The MMTI does not respond with the correct number of CDBRs or Handsets.
Isolation of the faulted componellt will require a process of elimination and possible component
swapping. Start by disconnecting the Inter-CDBR cable from the 12 port of the secondto last
CDBR. Repeatthe Handset/LAN test and determine if the correct number of components
connectedto the system is displayed If an incorrect number of componentsis displayed, repeat
the processuntil only the ARTU Data cable and one CDBR are connectedto the system. If the
Handset LAN test still fails, disconnect the ARTU Data cable from the ARTU. Perform a
continuity check on the ARTU Data cable. Be sure to check for opens, pin to pin shorts and pin to
shield shorts. Also check continuity of the shield from end to end. If the cable continuity checks
correctly, swap CDBRs and reconnectthe cable and CDBR. If the system still does not display
the presenceof a CDBR, then replace the ARTU.
V4.0A MNT Radio Re~
DIG Test
ESTABLISH
HANDSET LAN Result..
Pas.
TDI IN Sync
X Handsets Assigned
X CDBRaPresent
C-2000 reports engineering test ESTABLISHHANDSBT
LAN perfOC8.d.
:mS1A202
."
: ~t_:
Ro di8Play in the IDtr Radio RaSP0D888 window.
Did you wait greater than 15 seconds for the test to c~lete?
: SyqItoa: The wrong nU8ber of CDBRs and Handsets are displayed.
: Starting with the last CDBR, disconnect the cabling from the J2 connector
: of next CDBR in line. Then press .R. to repeat the test. If correct nU8ber
: appears, check the cabling. If cabling is correct, replace CDBR. If the
: incorrect nU8ber appears, repeat the above steps until the correct number
: of COBRa appears. If left with only one CDBR, check cabling and swap out
CDBR. If
problem
still
exists
replace
ARTU.
(R)eturn:Figure 9.1.8. Handset/ LAN MMTI Troubleshoot Screen.
9-11
RevB
~
FCC ill: CDG-ARTU
EXHIBIT C
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
9.1.9 RESET MAINTENANCE ACCESS PASSCODE
This test step will reset the Maintenance Access Passcodeto the factory setting of 0000. If the
Maintenance Access Passcodewas previously set to a value other than 0000 for protection purposes,then
the installer will want to reprogram the desired passcodeinto the system after completing the system checkout. Failure to reset the Maintenance Access Passcodewill only occur if the MMT is not communicating
with the ARTU.
Symptom: ERROR=> MMT communications failure timed out.
If this messageis displayed in the Radio Responseswindow then check the cabling between the
ARTU and the MMT. If the cabling is correct then press "Rtt to repeat the test.
V4. OAMMTRadio R.~
! C-2000
~rta
eDgineering
test
RESET DINT
~t08:
.RESET KA:INT ACCESSPDi perfo~.
a) Check IDrr cable connection.
b) Press .R. for repeat.
ACCESS pm
~~~-:t~--i
perf~
does not appear
..!
in IDrr window.
It should be noted that this test step changed the Maintenance Access PIN
to 0000. The Maintenance Acce.. PDi is required
to start
a maintenance
session when using the Handset. To change this value to a value other than
0000. use the Handset. s setup option.
Figure 9.1.9. Rest Maintenance Access PasscodeMMTI Troubleshoot Screen.
9-12
RevS
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2002:07:01 16:17:20Z Modify Date : 2002:07:17 14:14:54-05:00 Page Count : 16 Producer : Hewlett-Packard Intelligent Scanning Technology.3 Author : tjdrew [ TJDREW ] Creation Date : 2002:07:01 16:17:20Z Mod Date : 2002:07:17 14:14:54-05:00 Metadata Date : 2002:07:17 14:14:54-05:00 Creator : tjdrew [ TJDREW ] Has XFA : NoEXIF Metadata provided by EXIF.tools