Raytheon IIS ARTU Air-Ground Radio System User Manual installation manual part two
Raytheon Company Air-Ground Radio System installation manual part two
Contents
installation manual part two
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 257060 |
| Application ID | 9tHYc/qbknJFZXsfpy1m1A== |
| Document Description | installation manual part two |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 182.68kB (2283522 bits) |
| Date Submitted | 2002-07-17 00:00:00 |
| Date Available | 2002-09-17 00:00:00 |
| Creation Date | 2002-07-01 16:17:20 |
| Producing Software | Hewlett-Packard Intelligent Scanning Technology 3 |
| Document Lastmod | 2002-07-17 13:56:36 |
| Document Title | installation manual part two |
| Document Author: | tjdrew [ TJDREW ] |
FCC ID: CDG-ARTU
MAGNASTAR
EXHIBITC
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
CDBR/AIU
a) The mounting location of each CDBR/AIU should be accessible at later times for
system checkout and troubleshooting.
b) Prior to unit installation, perform a visual inspection on each unit for damaged
connectors or mounting hardware.
c) When connecting device cabling to a unit, insure that the connectors are fully engaged
and that the screws joining the connectors are securely fastened. Also ensure that
proper cable strain relief is provided at the unit interface to eliminate possible latent
stress damage problems.
d) Only cables that are to be used with equipment presently installed in the aircraft shall
be connected to each unit (i.e. cables placed in the aircraft for future expansion of
system capabilities shall not be connected to a CDBR/AIU).
Note: Only one digital phone shall be connected to a CDBR digital handset port.
Do not connect more than one digital phone to a CDBR digital handset phone port.
(Do !!.2! make a "split" phone cable to connect two phones or two jacks to one
CDBR phone port.)
HANDSETS
5.1.16.1
Generallnfomation
a) Prior to Handset installation, perform a visual inspection of each Handset and
Handset cable for damaged connectors or mounting hardware.
b) When connecting a Handset to the Handset cabling, insure that the connector is fully
engaged.
c) After the Handset is installed in the aircraft, remove the Handset from its holder and
insure that the Handset cord ratchet mechanism functions properly.
d) Replace the Handset in the holder and insure that the Handset seats properly.
5.1.6.2.1
System Overview
The MagnaStar C-2000 Airborne Radio Telecommunications Unit (ARTU) operates a
Local Area Network (LAN) bus. which LAN repeaters such as the CDBRs and the CAS
use to interface with the ARTU. A Cabin Distribution Bus Repeater model 1 (CDBR-1) is
used to interface one or two digital handsets to the system. A Call Alerter Switch (CAS)
can be used to interface a ringer to each digital handset to the system.
5.1.6.2.2
CDBR-1/Handset Cable (W6)
The CDBR-1/HandsetCable is identified as cable W6 in the C-2000 Interface Control
Document (ICD). If needed, refer to paragraph 2.3.4.1 of the C-2000 ICD for specific
information about the pinouts or components of W6. W6 P1 connects to the CDBR-1 J3
or J4, and P2 provides a connection point for the digital handset
S-3
RevB
FCC ill: CDG-ARTU
EXHIBIT C
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
Figure 5-2 MagnaStar C-2000 System
5.1.7
FAX/MODEM CABLE
a) Prior to FAX/modem cable installation, perform a visual inspection on the
FAX/modem, the
Handset and the RJ-11 cable for damaged connectors or
mounting hardware.
b) Remove the Handset from the bezel and connect the RJ-11 cable to the FAX/modem
machine and the Handset.
c) When connecting the FAX/modem to the Handset, insure that the RJ-11 cable
connectors
are fully engaged.
d) Place the Handset back in the bezel. Insure that the RJ-11 cable is not pinched or
damaged
when the Handset is placed in the bezel.
5.2
AIU SOFTWARE COMPATIBILITY
The operation of the AIU requires MAGNASTAR software Version 2.28 or later.
After all the MagnaStar system components have been completely installed with the AIU
connected to the HF or intercom equipment. apply power to the system and verify the
software version of the ARTU. This is done by use of the Set-up and Maintenance
screen on the handset. From the main menu press '9' to select Setup, press '3' to select
Info from the Setup Menu, and finally press '+' from the Info menu. The ARTC software
version will be displayed, verify that the version is 2.28 or later.
If the software version is not 2.28 or later you will need to download the current version of
ARTC software. Contact your dealer or call Teledyne Controls (1-888-246-STAR) for a
copy of the current software and technical assistance.
5-4
RevB
FCC ill: CDG-ARTU
EXHIBIT C
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
AIU FIELD ALIGNMENT PROCEDURE
5.3
The following alignment procedure should be used when an AIU is installed and
interfaced to a HF radio or to other equipment, which will require input from J3 pin 3 of
the AIU. This is a manual alignment procedure that adjusts the audio level that is output
at J3 pin 3 of the AIU. The level of this output audio should be set to the specification of
the extemal device that will be using it.
A. Tools And Required Equipment: The following items will be required:
1. Screwdriver: 1/16 Flat Head Adjustment Tool
2. Volt meter
B. Alignment Procedure: The following procedure outlines the required tasks to
perform this alignment.
Procedure
Using the specification of the external device. which will receive audio from J3
pin 3 of the AIU. note the nominal level which should be applied to its input for
normal operation.
Audio Input Level for the Extmal Device
2.
VAG RMS.
Connect the positive lead of the voltmeter to the AlU test point located on the
side of the AIU case and then place the negative lead on any point of the AIU
case. Setthe meterto measureAC volts RMS.
3.
Using one of the MagnaStar handsets setup a HF link:
From the handset's Main Menu,
Press '6' to select the "Link" option.
Press '3' to select "HF Radio" (this label can be customized).
4.
With the HF link now connected continually press (or with ARTC 4.0A software
and above press and release repeatedly) anyone of the handset's numeric
keypad digits to generate a fixed tone. This tone will in turn generate and audio
signal at J3 pin 3 of the AIU.
5.
Using the voltage measurement read on the voltmeter and the adjustment
tool/screwdriver, set the AIU audio output level to the level noted in step 1, by
turning the adjustment potentiometer located through the hole in the AIU cover.
6.
Tenninate the call and remove the meter. Place the adhesive backed circular
aluminum cover PN 513917-2 packed with the unit over the AIU adjustment hole.
5-5
RevB
FCC ill: CDG-ARTU
MAGNASTAR
EXHIBIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
EQUIPMENT CHECKOUT WIffi MAGNASTAR MAINTENANCE
TERMINAL (MMT)
6.0 EQUIPMENT CHECKOUT WITH MAGNASTAR MAINTENANCE TERMINAL (MMT) ..6-1
6.1 INTRODUCTION
6-1
6.2 TEST EQUIPMENT REQUIREMENTS
6-1
6.3 C-2000INSTALLA TION CHECKOUT with MMT
6-2
6.3.1 MMT COMPUTER SET-UP
6-2
6.3.2MMT CABLECONNECTION
"'...'...' " "..'
"'.'.'
6-2
6.3.3 EXECUTING MMT SOFTWARE
6-2
6.3.4 MMT OPERATION
6-3
6.3.5 INTRODUCnON TO THE MMT INSTALLATION TUTORIAL
6-4
6.3.6 C-2000SYSTEM POWER UP
6-5
6.3.7 MMT COMMUNICATION VERIFICATION
6-6
6.3.8 START ARTU OPERATIONAL SOFTWARE
6-7
6.3.9 LOCKED OFF-LINE STATE
6-10
6.3.10 ARTU MOUNTING TRAY FAN TEST
6-11
6.3.11 ARTU TRANSMITTER POWER OUTPUT MEASUREMENT
6-12
6.3.12 RECEIVE SIGNAL STRENGTH MEASUREMENT
6-14
6.3.13 HANDSET I LAN TEST
6-17
6.3.14 RESET MAINTENANCE ACCESSPIN
6-18
6.3.15 UNLOCKED ONLINE STATE
6-19
6.3.16 RECEIVE SIGNAL STRENGTH MEASUREMENT USING GENSTAR GROUND
STA TION
6-20
6.3.17 C-2000INSTALLATION CONCLUSION
6-22
6-i
RevB
FCC ID: CDG-ARTU
EXHlBrrc
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
6.0 EQUIPMENT CHECKOUT WITH MAGNASTAR MAINTENANCE TERMINAL (MMT)
6.1 INTRODUCTION
The MagnaStar Maintenance Terminal (MMT) consists of a laptop computer executing application
software. The MMT is connected to the ARTU via the computer's serial port. The MMT is used
to control the ARTU and monitor its functions. The MMT software includes an Installation
Tutorial. This tutorial is a step-by-step procedural test that verifies the C-2000 installation. When
the tutorial runs a particular test, a description of the test, the expected results of the test, and the
actual results of the test will be displayed to the user. A troubleshoot screen is also available with
each test step that provides a short description of steps to use for troubleshooting the system.
The MMT is a very powerful tool for verifying and troubleshooting a MagnaStar C-2000
installation.
This section of the equipment checkout provides a text description for each individual test step of
the MMT and a procedure with the necessary steps to accomplish each test step. The text
describing the necessary steps to perform each test are shown in bold print.
Cable checkout, Section 4.0, and equipment installation, Section 5.0, should be completed before
starting this section. Troubleshooting procedures screens are available while using the MMTI.
These screens and troubleshooting information can be found in Section 9.0.
The following MMTI screen information corresponds with MMTI software version 4.0.A.
6.2 TEST EQUIPMENT REQUIREMENTS
The following list defines the test equipment necessary to completely check the functionality of
the C-2000 system using the MagnaStar MaintenanceTerminal.
1)
2)
3)
4)
5)
MagnaStar MMT Installation software version 4.0
(MX 902156)
386 or 486 IBM compatible computer with 4 Megabytes of extended RAM
Power Meter or Thru-line Watt meter for 895 MHz (20 watt minimum capability @ 900 MHz)
MMT cable
(MX 422632-801)
MagnaStar Loop-Around Test Set
(MX 902185-802)
6-:
RevS
FCC ill: CDG-ARTU
MAGNASTAR
EXHIBITC
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
6.3 C-2000 INSTAllATION CHECKOUT with MMT
The installer
a)
b)
c)
must know the following information before starting the MMT Installation:
The number of CDBRs and AIU's that are used in the installation.
The number of Handsets that are to be used in the installation.
If the location at which the installation is being performed will support
communications with a GTE AIRFONE GenStarTM System Ground Station.
6.3.1 MMT COMPUTER SET-UP
See Section 8 for computer set-up.
6.3.2 MMT
CABLE CONNECTION
The MMT computer is to be connected to the ARTU using the MMT cable. (The MMT interface is a RS232C serial interface.)
Connect the 9 pin D type connector of the MMT cable to the "COM .. port of the MMT
computer.
Remove the protective cap from the MMT connector of the ARTU.
Connectthe circular connector of the MMTcable to the MMTconnector on the ARTU.
6.3.3EXECUTING
MMT SOFTWARE
The following commands are to be used to start execution of the MMT application software in the
computer.
If required. power up the computer and wait for the computer to completethe boot
process. It is assumedthat the computerwill boot up to the "C" drive with and
have no other applications running.
Change the directory to the MTU directory, type: "CD MTU and press "ENTER",
C:> cd mtu
To start execution of the MMT software from the MTU directory, type: "MMTI" and
press "ENTER".
C:\MTU> mmti
Note: when the computer is executing the MMT software. the computer will be
referenced as the "MMr .
6-2
RevB
FCC ID: CDG-ARTU
EXHIBITC
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
6.3.4 MMT
OPERATION
This step selects the installation tutorial mode of operation for the MMT from the from the start-up
options menu after the MMT software has started execution.
When the MMT software has started execution, the computer screen will display information in
two windows as shown below in Figure 6-1. The upper window is the MMT Radio Responses
window which is used to display feedback (response) informationfrom the ARTU. The installer
will view the information in this window to verify proper performance of the C-2000 system during
the installation. The lower window is the MMT Menu Prompt window which provides the installer
with command options and provides a short summary of tasks for the installer to perform.
Verify that the MMT cable connects the computer to the ARTU.
With the MMT computer screen display shown in Figure 6-1, type "2" and then
press "ENTER" to select the MMT Installation option.
Note: The MMT CommandMenusoptionis reserved for troubleshooting activities.
V'.OA
MagDaStar
: ~
DOS-8xt8Dd8r
HNT Radio
Proprietary
Re8PQaae
Soft~e
HNT Version'.
OA
IKS'1'ALLD VDS%c.
(C) Copyright
1.99' Raytheon
SystC~
(C) Copyright
1.986-1.99'
Pbar Lap Soft~.,
Attach
Seria1. Cable
%Dc. ..
D81.-9S03
C-2000
1. - Start."
2 - Start."
Select
.-'!'
HNT ~u
~t
STARTUP OP'1'%c. .au
- C~
NeDus ( UTO
- %D8tallatiOD
.tart-up
option
or
CDB%)
(1. - 2, Q to QUit ~):
~~~~
Figure 6-1. MMT Installer display screen #1
6-3
RevB
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
6.3.5 INTRODUCTIONTO THE MMT INSTAllATION TUTORIAL
An introduction to the MMT Installation tutorial will be displayed on the MMT as shown in Figure
6-2. This screen provides information on the instructions necessary to move from one test step to
another within the installation procedure. After reading the introduction, continue with the
installation as follows:
Type "C" to go to the next screen.
V~.OA.-T
-.dio
Re8PQD8
V~.-T
ms~Ol
.-T
D8ASTAa
Tutorial
m8TALLATX~
fti.
tutorial
'-.or
Tutorial'
the
Objeotiv.
di8Playa
to
After
-oh
i.
cODdlacted .tep-by-.tep
wiDdow,
iD8tructiAg
of the .tep
aDd what
Ob8erve,
etc.).
~.-T
.tep,
' c ' ~tiaa.
'7'roubl..hoot
'.'epeat
'Q'uit
you ~
choo..
with
iAf~ti~
you what actioaa
r..ult.
to expect
operati0D8
will
ODe of
the
followiDg
pr.._ted
iD thi.
to take to acca8Pliah
(...8Ur888Dt.
to tak.,
be aut~te4
for you.
optioaa
at
the
PZ'a8Pt:
- Step ca8Pl.ted,
r.ady for th8 D8Xt iDatallatiOD
.tep
- Direct..
to troubl..hootiDg
iDfor8&tiOD
for thi.
.tep
- Let'.
try thi.
.tep agaiA
- X'a fiDi.be4,
quit th8 -.or iDatallatiOD
(C)~tiaa.,
(T)rouble.hoot,
(a)epeat,
(Q)uitl
Figure 6-2. MMT Installer display screen #2.
6-4
RevB
FCC ill: CDG-ARTU
EXHIBIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
6.3.6 C-2000 SYSTEM POWER UP
This step will apply aircraft power to the C-2000 system. The installer should view the indicators
on the front of the ARTU to verify proper operation.
Verify that the MMT display screen is as shown in Figure 6-3.
Apply aircraft power to the ARTU.
Note: insure that power has been removed from the unit for greater that ten seconds
prior to power up if the unit has been previously had power applied.
Observe the condition of the two indicators on the front of the ARTU.
The FAULT indicator should be "Off" (not illuminated).
The POWER indicator should be "On" (illuminated green).
If the condition of the two indicators is correct, type "C" to continue the
installation.
If the condition of the two indicators is not correct, proceed to troubleshooting
procedures (Section 9).
V..OA NNTRadio ~
D81A.102
..,
NNT Tu~ori~
~TD.
msULLA.ft~
:~I
tb8 U'IU.
Power-up
DnCftD
Power
"~81
ill4ic.~or
OD f~~
of
ARTU i.
illuaiDa~ed
(gZ'.~).
:ACT%~I
0 Apply
0 Ob8~
poweZ' to
D.ft.
poweZ' iDdicatoZ'
(C)OD~iau8,
i.
illuaiDa~ed
(~)zoab~88boo~,
(gZ"~).
(.)8P88~,
(Q)ai~1
Figure 6-3. MMT Installer display screen #3.
6-5
RevB
FCC ill: CDG-ARTU
EXHffiIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
6.3.7 MMT COMMUNICATION VERIFICATION
This step will verify that the MMT is properly communicating with the ARTU. View the data in the
MMT Radio Responses display window. The MMT display screen will be similar to that shown in
Figure 6-4.
Observethat the MMTdisplay screen is similar to that shown in Figure 6-4.
Verify that the MMT Radio Responses screen displays the ARTU software file
names.
(Note: the actual version numbers of the software loaded in the ARTU will be
displayed on the MMT in place of the # characters shown in the window below. A letter
will replace the X.)
If the MMT Radio Responses window displays the software file names, type "C" to
continue the MMT installation.
V..OA ~
Radio aesp0a8es
:Pow8r-up Statusz
AaTC code
rile
os.
code rile
80376 Kicroproeessor
OK. SRAN OK.
~IIX.s.x
Ver 1.1 Date IIIIIIII
HDSPCllx.BBX Ver 1.1 Date IIIIIIII
8%T
8oot
code
code
rile
rile
-.410 sort~
mBlAl03
KaXTClIX.s.x
M_8TC1IX.s.x
Ver
1.1
Ver 1.1
11:11
11:11
BaDk I CRCzlll1
BaDk I CRCzIIII
IIIIIIII
11:11
BaDk I CRCzIIII
Date IIIIIIII
11:1'
BaDk,
Date
CRCz""
is DOt -ecuting
VlA MMT Tutorial
that
Veriry
tha Aftr1 is c~cating
properly
with
tha ~.
: DnC'1'8D
: Aa'l'U'
RUULTS:
sor~e
ril_s
are displayed
in
the
Radio
ae8P0D8es
wiDdOlfz
c0d8
-os.
c0d8
:AC'r:tC8Sz
rile
rile
ARTCC"X.BBX Ver 1.1
HDSPC"X.BBX Ver 1.1
Date "/"1,'
Date fl/"/ll
11:11
11:11
BaDk I CRCzI",BaDk I CRCz"I'-
0 Oh8erve 8Ort~e
ril-
displayed
in ~
Radio Re8P0D8es wiJIdow.
-AaTC
mSTALLA.TXC8
'O8.J.corxv.z
~Aa
(C)ootiDue.
(T)roableshoot.
(R)epeat.
(Q)uit:
Figure 6-4. MMT Installer display screen #4.
6-6
RevS
FCC ill: CDG-ARTU
EXHIBIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
6.3.8 START
ARTU OPERATIONAL
SOFTWARE
In the following steps. the installer will start the execution of the ARTU operational software and
verify successful completion of Power-up Built-ln-Test (BIT). Operation of the Power-up BIT is
verified by observing the status of the ARTU FAULT indicator and viewing the results in the MMT
Radio Responses window.
Type "C" to start ARTU operational software. Once the command is given to start the
operational software. Power-up BIT will begin execution.
Note: The time to complete Power-up BIT may vary from one to five minutes depending on the
amount of time the ARTU frequency reference requires to warm-up.
Observethat the MMTdisplay screen is similar to that shown in Figure 6-5.
V4.0A -.T
Radio aespouaes
Btatusz
80376
Microprocessor
AaTC code rile
AaTCC'Ix.RBX
DBP code rile
BZT code rile
Boot code rile
Radio software
OK, BRAN OK.
Ver 1.1
Date .1/.'1'1
Ilzll
BaDk I CRCzI'"
HDSPC"x.RBX Ver 1.1
Date "1"/'1
IIz"
BaDk I CRcz.'"
HBZTCI.x.BBX Ver 1.1
Date "1"/"
"zI'
BaDk,
CRcz""
H_BTC"X.BBX Ver 1.1
Date '.1"1"
"Z"
~.
CRcz""
:Pow8r-up
is Dot executing
: mBU.lO.
: 08J8C'fIV8:
: V.rify
that
8'1'
-.T Tutorial
KAC8AS'1'U ZRS'l'ALLA'1'I<8
pGW8r-ap BQilt-ID
T..t
(BI'1') begiua
executioa.
: DPBCftD
auUL'l'S:
: hult
iDdicator
CD front
of AR'l'O i. ill1miDated
(red).
: Power-up 81'1' re.ult
_..ag..
are 4iaplayed
in -.T Radio
a.8PQD8..
window.
:AC'rZ~s
0 Pr...
'C'CDtiDDe
to
begiD
pGW8r-ap
BIT
..ecutiCD.
(C)~tinu.,
(T)roabl.8hoot,
(a)~t,
(Q)1Iits
Figure6-5. MMT Installer display screen #5.
6--7
RevB
FCC 10: CDG-ARTU
EXHIBITC
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
Type "c" to start ARTUoperational software.
that the MMT display screen is now similar to that shown in Figure 6-6.
Observe
Observe that the FAULT indicator should be "On" (illuminated red) indicating that
Power-up BIT has started.
Next observe that the MMT Radio Responses window display is similar to that
shown in Figure 6-6 for approximately 10-15 seconds after the start of Power-up
BIT.
After approximately a 10-15 second delay, the MMT Radio Responses window will
display the various BIT tests and a pass/fail status as each test is completed.
After approximately30 seconds, Power-upBIT may appearto stop running.
During this time period the ARTUsoftware is waiting for the frequency referenceto
warm-up. This warm-uptime may vary from 1 to 5 minutes (at room temperature).
After the frequency referencehas warmed-up,several more BIT tests will then be
completed.
Vt.OA NNT Radio a..pQD8
DZ~
1'0. ~-OP
pr...
aa4io 8Of~.
8!' baa ~
.taRing
_cuti~.
recca.figured
for
DSUJ.O5
:o
ac"i'%V8.
Verify
8!'
s-zy
power-up
~r-up
.C-2000
:AC'nC8S
U'IU
to
Texaioat.
Wait
Port
1. at 9.6 kh8.
8!' Tutorial
C-2000 mSTALL&T%<*
tbat
:BDBC'l'BD USOLTS:
: Fault iD4icator
B%T USULTS «5 HDO'rB ~T)
'B.c'
~-OP
8Qilt-%D
CD frCDt
B:IT r..ult
BrT
Teat
of ARTU i.
_..ag.
(B%T) CO8Pl.t..
extiDgUi.be4
i. 4iaplay8d
8Ucc...fu1.1.y.
(off).
in ~
".apoD8..
wait for paw8r-up 8I~ to CQ8Plete (aay take up to five
0 Ob8erve fault
iDdicator
light
i. .xtiDgui8bad
(off).
-ry
wiJJ4ow:
pa..84.
aiaat..).
0 Ob8erve
~-up
8%~ re.ult
-.-ge
(C)ODtimue,
(~)roable8boot,
iDdicate.
(Q)uit:
paa-S.
Figure 6-6. MMT Installer display screen #6.
6-8
RevS
FCC 10: CDG-ARTU
EXHIBIT C
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
The installer should observe two indications that Power-up BIT testing has
successfully been completed:
First, the MMT Radio Responses window will display "C-2000 Power-up BIT
Passed", as shown in Figure 6-7.
Second,the installer is to observe the FAULTindicator. The FAULT
indicator should be "Off" (not illuminated).
After successful completion of Power-up BIT. type .'C" to continue the MMT
installation.
If the ARTU does not successfully pass Power-up BIT, proceed to
Troubleshooting
Procedures (Section 9).
V&.OA HMT Radio Re8PQDa
.X~ 78.~ POWER-UP
ax~
C-2000 ~-UP
0 f~
C_auded
S.l8C~
pa..ed.
raul~:
arr pa..ed
.X'1' Meuu to vi-
00 00 00 00
ax'1' a..ult.
Radio .of~
_tiDg
iD UDloeked ~liDe
~.-'!'
mSlAlOS
,""-O=---=~-~ :
.-r
V.rity
~t
~-up
'1'utorial
D.-aB'1'U
a.ilt-%D
.tat..
C-2000
78.t
ms'1'ALLA.'1'X~
(B%'!') CO8pl.t..
II
8Ucc...fu1~y.
:UPBC'rBD
USUL'1'S:
Fault iDdicator
S-zy
OD froDt of AR'1'Ui.
~r-up
an r..ult
_..ag.
.C-2000
POM8R-UPBrr P...ed.
axtiDgui.hed
i. diaplay.a
(off).
iD ~
...P0D8'.
:AC'1':EC8S:
0 Mait
wiD4ow:
for
Oba.rY8
0 Oh..rY8
po.er-up a%'1'to ca8pl.t.
(aay ~.
up to fiV8 aiDQt..).
fault
iD4icator
light i. axtiDguiahed
(off).
po.er-up
err r.nlt
_..age
iDdicat..
paa~.
(C)ODtiDa.,
('1')roahl.8hoot,
(Q)uitz-
Figure 6-7. MMT Installer display screen #7.
6-9
RevB
FCC ill: CDG-ARTU
EXHIBITC
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
6.3.9LOCKED OFF-LINE STATE
After successful completion of Power-up BIT. the ARTU is to be placed into a locked Off-line state
by the MMT software. This mode of operation will allow the installer to control and test selected
ARTU functions that cannot be easily tested in a normal operational mode.
The MMTdisplay screen should be as shown in Figure 6-8.
Verify that the ARTU is in a Locked Off-line state by observing the MMT Radio
Responses window for the "Radio software executing in locked offline state"
message.
Type "C" to continue.
V..OA NNT aadio
a.SP0D8.s
Radio
software
exeeu~iDg
in
locke4
offline
s~a~..
VtA ~
D8AS'rAR.
IaUlO6
Tu~orial
x.8'rALLa.7X~
:OBJBC'nftz
Verify
tha~
AaTO ...
pQ~ in~o
locked/offline
s~a~..
:DP~-TKU
Following
RESULTS:
_..age
-Radio
aoftware
di8Played
in
executiDg
in locked
Iarr
Radio
aeap0D8e.
offliDe
wiDdowz
atate.-
:ACTZ~S:
0 Ob88rv8
above
-."9.
in
.-r
Bad1o
R..pcaa..
window.
(C)ODtinU..
(T)roubl..hoot.
(R)epeat.
(Q)uit:
Figure6-8. MMTInstallerdisplayscreen#8.
6-10
RevB
FCC ID: CDG-ARTU
EXHffiIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
6.3.10ARTU MOUNTING TRAY FAN TEST
This step will verify that the ARTU Mounting Tray fan is functional.
The MMT display screen shall be as shown in Figure 6-9.
Verify that the ARTUMounting Tray fan is operating.
Observethat the Mounting Tray fan exit airflow is not restricted or blocked.
Type "C" to continue.
Vt.OA HMT Radio a..pooa
C-2000 report.
~~~iDg
t..t
FA» CC*TaOLperf~.
x..~O7
8T
HMT TutQ&"~
lI&8&S'l'AR
mSTALLAT1:C8
:08J8C'r:EV8:
Vez-ifJ' that U'I'U'.
KoaDtiDg '!'ray PaD operat..
~1J'.
: DPBC'l'BD
USUL'l'S
ARft MoIIDtiDg'rray PaDoperat...
Airfl~
~t
o~ back of AR'l'UNoaDtiDg 'l'ray i.
QOt r..tricted.
:AC'l'%~1
0 Ob8ezve that AR'l'U~tiDg
'!'ray PaD i.
0 ob8.rve that air~l~
i. QOt r..tricted
opezoatiDg.
~t of back of MoIIDtiDg '!'ray.
(C)ODt1au..
('l')roUbl..boot.
(a)epeet.
(Q)uit:
Figure 6-9. MMT Installer display screen #9.
6-11
RevB
FCC ID: CDG-ARTU
EXHIBITC
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
6.3.11ARTU TRANSMITTER POWER OUTPUT MEASUREMENT
These test steps will measure the ARTU transmitter power level at the Antenna port of the
Duplexer. The installer will be required to disconnect the Antenna coaxial cable from the Antenna
port of the Duplexer and insert a power meter or thru-line watt meter between this port and the
antenna. Be sure to have either a 50 ohm RF load or antenna connected to the thru-line watt
meter. The ARTU will then be commanded to transmit a CW carrier for measurement. It is very
important that the installer properly protect the test equipment from damage by the ARTU
transmitter output which can have an average power level as high as +42 dBm (16 watts). After
the power measurement is completed. the ARTU will be commanded to stop transmitting and the
Antenna coaxial cable is to be reconnected.
The MMT display screen should be as shown in Figure 6-10.
The installer is to disconnect the Antenna coaxial cable from the Antenna port of
the Duplexer. A Power Meter is to then to be connectedto the Antenna port of the
Duplexer. If a thru-line watt meter is used, be sure to reconnect the antennato the
output terminal of the thru-line.
CAUTION: PRESSING "c" WILL MAKE THE ARTU TRANSMIT. THIS PRESENTSA
RADIATION HAZARD FOR PERSONNEL WITHIN 5 FOOT OF THE ANTENNA.
ENSURE THAT THE LOOP-AROUND TEST SET IS SET UP AND CONNECTED
PRIOR TO INITIATING THE TEST SEQUENCE. The Power Meter, with or without
padding, shall be capable of withstanding average power levels as high as +42 dBm (16
watts) without damage.
Once the Power Meter is connected to the Duplexer, the installer is ready to
command the ARTU to transmit. Type "C" to command the ARTU to start
transmitting.
Note: Execution of this command may take from ten to thirty seconds to complete during
which time the MMT may appear to be stopped or several command screens may appear
to flash by and momentarily stop before the test is configured in the MMT.
vt.OA HHT Radio R..p0a8
:I
C-2OOO
r.port.
~.x-iDG
: ms~O8
08JKC'1'IV8:
.r~
t..t
to -.ur.
Aa'rO'.
PAR~OL
~rf~.
MMT Tutorial
D8AS'l'U
mftALLl.tlI~
~tPlt
po-.r
OD po-.r
_t.r.
: BDBC'l'BD USULTS:
: .~
-ter
~ct~
to dupl_.r
in pr.paratiOD
to -a~
~r
~tPI&t.
:ACTI~S:
: 0 Di.coaaect
aut8DD& cable
fro.
4upl_er.
: 0 Coaaect BP ~r
_ter
to 4upl.-r.
: Bot.: pzo_.iag'C'ODtinU.- will caus.th. radio to begint~ttiDG.
(C)oatiau..
(tI)roubl..hoot.
(R)epeat.
(Q)uit:
Figure6-10. MMT Installer display screen #10.
6--12
RevB
FCC ill: CDG-ARTU
EXHIBITC
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
The MMT display screen shall be as shown in Figure 6-11.
Observe
the ARTUtransmitter output power at the Antenna port of the Duplexer
using the Power Meter. This level shall be greater than +36 dBm (4 watts).
V6.0A MHT Radio ae.POD.e
C-2000
report;.
te.t
eqiDeeriDg
TOMB SYBTBUXZD
perfoz-.cl.
MMT
XBSU3.09
MMT TUtorial
DS'l'ALLATXC8
~U
:0BJBC'1'%V81
Verify
power
OIItput
of
AR'1'IJ.
: ZD~TED
USULTS:
Pow.r ..ter
re&diDg .bould be greater
thaD +36 dB8 (6 Watt.).
AC'1'%~ :
0 Ob88%V8po-.r
_ter
r8a4iDg to be -
expectad.
(C)OD~iDu.,
(7)roable8boo~,
(.)epea~,
(Q)ul~:
Figure 6-11, MMT Installer display screen #11
Type "C" to command the ARTU to stop transmitting.
The MMT display screen should now be as shown in Figure 6-12.
Reconnect the Antenna coaxial cable to the Antenna port of the Duplexer.
V'.OA HNT Radio a..p0a8
C-2000 report.
811GiDeeriDgt..t
S'l'OPTRANSIa'1'
perfoz88c!.
D81A1.10
V~
~'1'U
Tutorial
m8'1'ALLa.n~
:~r
Verify
AaTU has
.topped
trU18aittiDg.
: DnC'1'ZD
USOLTS r
: Po-.r
-ter
r.a4iDg
.hOIald
iDdicat.
DO t~t
.igDal
pr..ent.
:ACT%C8Sr
0 Ob.8rV'8 power -ter
0 Di.~.ct
0 C_t
readiDg
power _ter
ant-
f~
to be -
expected.
d'iPlexer.
cable to d1iplexer.
(C)ODtiDa.,
(~)roubl..hoot,
(a)~t,
(Q)uitl
Figure 6-12. MMT Installer display screen #12.
6-13
RevB
FCC ill: CDG-ARTU
EXHffiIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
6.3.12RECEIVE
SIGNAL STRENGTH MEASUREMENT
This step will use the ARTU to measure the Receive Signal Strength (RSS) of the C-2000 system
in an RF loop-around configuration using the MagnaStar Loop-Around Test Set. This test will
verify the performance of the aircraft RF interface between the ARTU and the Antenna.
In this test, the ARTU will transmit a OAM signal at frequency of 894.9495 MHz. This signal will
be frequency translated (i.e. mixed) by 45 MHz to a frequency of 849.9495 MHz and transmitted
back to the ARTU via the MagnaStar Loop-Around Test Set. Both the TSC and Pilot receivers
are tuned to the receive frequency. The installer is to the view the RSS value of the loop-around
signal to verify the RF signal path of the C-2000 system.
The following steps are to be used with the MagnaStar Loop-Around Test Set.
Type "C" to begin the Receive Signal Strength test step. The MMT display screen
should be as shown in Figure 6-13.
Turn "ON" the Loop-Around Test Set.
Measure that the MagnaStarLoop-AroundTest Set battery voltage is greater than
6.0 volts DC by pressing the battery check switch. If the Battery check LED
illuminated, then the battery is within tolerance. Otherwise replace the battery.
Carefully place the clip-on antennatest fixture (at one end of the MagnaStarLoopAround Test Set cable) onto the center of the MagnaStarantenna. Centerngof the
clip-on antennaonto the aircraft antenna is necessaryfor best results.
Set the attenuator on the Test Set for 30 dB attenuation. (Attenuation switched
"On".)
v~. OA HNT Radio
:'
K8.P0D88
~~
: :laU200
8'r
:08.7E'r:EV81
,,
Prepare
:DPac-~
to _a.ur8
DaASTU
8Y8t-
MMT Tutorial
C-2000
:EU~nC8
r8C8i~
.igDal
.treDgth.
RB8ULTS
,,
Tbe HagnaStar loop aroaDd t..t
_tin preparati~
to ~
box i. to be CODDeCted to the aircraft
rec.i~
.ignal
.tr8Dgth.
0 C-.ct
the HagnaStar loop arouD4 t.at box to the aircraft
0 s.t po.er aDd atteauator
.-itch
to the "OR- PO8iti~.
:AC'l'ZORS I
ant_.
: 8ot.: pr...iDg 'C.~tiDU. :
(C)~tiDU..
II
will cau.. the radio to begint~ttiDg.
(T)roubl..boot.
(K)epeat.
(Q)uitl
:I
Figure 6-13. MMT Installer display screen #13.
6-14
RevB
FCC ill: CDG-ARTU
EXHIBIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
Type "C" to start the ARTU transmitting a QAM signal for loop-around testing.
Note: Execution of this command may take from ten to thirty seconds to complete during
which time the MMT may appear to be stopped or several command screens may appear
to flash by and momentarily stop before the test is configured in the MMT.
CAUTION: THE ARTU IS NOW TRANSMITTING ABOUT 10 WATTS. THIS
PRESENTS A RADIATION HAZARD FOR PERSONNEL WITHIN 5 FOOT OF THE
ANTENNA. ENSURE THAT THE LOOP-AROUND TEST SET IS SET UP AND
CONNECTED PRIOR TO INITIATING THE TEST SEQUENCE.
The MMT display screen should be as shown in Figure 6-14.
The installer will observe the RSS value for both the TSC receiver (TxRx) and the
Pilot receiver (Rx) in the MMT Status Updates window as explained in the next
step.
V&.OA MMTRadio ...~
C-2000
report.
.tatu.
update
BRABLZD.
Pr...
P2 to
Vi..
Statua
ni8P~
XR81A201
.-T
~.-T
HAl8ASTU
Tutorial
m8'rALLA.'1'%~
:~:
V.rify
aeceiv.4
SigDal
Strength
(US)
fr~
'1'SC/Pilot
:DP~
~.
USUL'1'S:
US reported
for
> -95 dBa (..
.~
TxRx aJI4 for ... on the
below):
TxRx
US TxRx
-A8.igD88Dt:
-US
(dba):
'1'06:25
- II
0.0
Statua
Updat..
wiaaow
are
.ach
MOR 1"
- II-
:AC'1'%C88:
0 Pr...
r2
to
viUS a.
(C)oatiDue.
above OD 8'J'
('1')roubl..hoot.
Statua
Q»dat..
w!D4OIf.
(a)epeat.
(Q)u!t:
Figure 6-14. MMT Installer display screen #14.
Press the "F2" function key once to view the MMT Status Updates window.
After pressing "F2" key, the MMT Status Updates window should be similar to the
that shown in Figure 6-15.
Note the values of the RSS readings of the TxRx and Rx receivers. These values
should be between -107 dam and -99 demo (The RSS readings will vary
dependent on the placement of Loop-Around Test Set clip-on antenna placement,
cable losses and other system variables.)
6-1S
RevB
FCC ID: CDG-ARTU
EXHIBIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
Set the attenuator switch settings on the MagnaStarLoop-AroundTest Set for
0 dB of attenuation. (Set the attenuator switch to .'Off".)
View the RSS values on the MMT Status Update windows. These values should be
approximately 30 dB higher than the values noted prior to the attenuator change.
upaa~
XD: B800( 064h
S~a~U8
: Aircraf~
Rx measurement
"dio
~o Prj,c,r
Menu)
U'rU
ftATUS
(~l..
StatU8 ScreeD)
(Pl.bturn
xD..aOOOl
'l'2:Rx
:A8.i~~:
'r~
:US
(~):
:Doppl.r
(8s):
:Oper Sta~.,
BRA
:'1'SC/ACC S~a~.:
SsPOD
: Ch 'l'o~ lOx':
:Ch Err 10x3:
:Ch ...
: .000000
: acL 'ro~ 10x3 I
:RCL Errl
:acL'"
I .000000
:B8Ddoff
-oftl
Bathed
RBS ~
Rx
0.0
BRA
.000000
:ca11 bfl
:Bearer
Capl
:Rx Ctrl,
:"- Cull
trSC 1/1
RaDQAM
CODtrl..OrI'LXD
Rando!!
Stat.:
~l.
8wi~ch:
:rJIdica~or
o.cil1a~orl""
OUT
I on
.000000
CPO %41..
',
: trSC Sta~.:
Aa'rO
StatAd8iD : LOCK
Oper . aA.
ATaJ.l.: 8OT DQ v...
ma.
trSC 1/3
a.DQAK
Figure 6-15.
0% (CIa)
0% (J:II8~)
Call
C~l:
Low AC8:
High AC8:
Pil.
Xfr:
MMT Installer display screen #15.
UTU
Press the "F1" function key once to return to the MMT installation menu. The
MMT display screen will again be similar to that shown in Figure 6-14.
Next type "C" to proceedto the next step and to turn "Oft" the ARTUtransmitter.
Tum the MagnaStar Loop-Around Test Set "OFF" to conserve battery life.
6-16
Rev 8
FCC ID: CDG-ARTU
EXHIBIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
6.3.13 HANDSET I LAN TEST
This step will verify the number of CDBR/AIUs and Handsets that are connected to the ARTU.
The installer is required to know the number of CDBR/AIUs and Handsets connected to the
system so that these numbers may be compared to the value with which the ARTU is able to
communicate. It should be noted that the Handset ILAN test will report an AIU as a CDBR.
The MMT display screen will now be similar to that shown in Figure 6-16.
Note: The MMT Radio Response window may require as long as 20 seconds to return
withthe a properresponse.
Compare the number of Handsets assigned as reported in the MMT Radio
Responses window to the actual number of Handsets installed in the aircraft.
Compare the number of CDBR/AIUs present as reported in the MMT Radio
Responses window to the actual number of CDBR/AIUs installed in the aircraft.
Note: The Handset ILAN test will report an AIU as a COeR. A CAS will not be reported
as being present.
HMT
Radio
...~
:~
'!'e.t
: C-2000
BSTABLXSB BARDSET LAB a..ult..
PASS
Tl8XDSync
2 Ball48et.
Aa8igned
1 CDBR.8 Pre.ent
report.
eDgin_ring
te.t
BSTABLXSB BARDSET LU
V~
P8rfo~.
Tutoria~
%881A202
~AK
C-2000 mftALL&S':EI*
OBJBCT%V8
: V.rify
Duaber of CoaDeCted CDBa8 aDd BaJI48.t..
DP8corBI) USULTS:
Po~~owiDg -.-ge
-DO
T..t
di8P~ayed
in 8'r
Radio R..pQD8..
U'1'ABL%8B BARDSB'l' LAB "8U~t.:
'rI8 %0 Sync
. BaJI48.t. A8.igned
. CDBa8 Pre._t
window:
PASS-
0 Wait
0 Verify
:~%ORS:
at
~...t
~5 .ec0Dd8
for
abO98 r.8p0n8.
to
be di8P~aye4.
correct
DU8ber of c-.cted
CDBa8 aDd BaJI48.t. r~e4.
(C)ODt!Da.,
(T)roub~e8hoot,
(R)epeat,
(Q)uit:
Figure 6-16
MMT Installer display screen #16
6-17
RevB
FCC ill: CDG-ARTU
EXHIBU C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
6.3.14RESET
MAINTENANCE ACCESS PIN
This test step will reset the Maintenance Access Passcode, stored in the ARTU Non-Volatile
memory, to the default value of (0000). This action is to insure that the installer knows the
number to which the Maintenance Access Passcode has been set.
The MMT display screen will be similar to that shown in Figure 6-17.
Verify that the MMT Radio Responses window displays the following message: "C2000 reports engineering test RESET MAINTENANCE ACCESS PIN performed".
Type "C" to continue with this test step.
V..O&.-T
C-2000 report.
eDQ'iDeeriDG t_t
Ba4io ".poaa
a8n'r
DIft
:.
ACC888 pm perfo~.
:%881A206
..,
:C8.I~-T~Y.1
-.r
Tutorial
~U
:E88'rALLA.n..
: Verify that tha 8aDd8.t _iDt_.
aO088.p~
i. reporte4 -~.
:8DBC'1'8D
U8ULT8
_..ag.
.C-2000 report.
rollowing
41aplayed in ..,
engiDeeriDG t..t
aadio bapcma.. wiDdow:
usn D%8T ACC888pm perf~..
0 vez1fy ahoY8 _..&g8
: 'rh8_1II.t: (0000). 'rh8
:AC'r:E~1
418Pl&yed 111.~
&co... PUSCOI8
ba8P~8CO18 -y
(C)ODt1Du.,
b410 h~..
wiDdow.
heeD..t to the default Yalu. of
be chaDge4 u.1Dg th.
(~)roubl.8boot,
(.)~t,
BaD48.t.
..tup
(Q)u1tl
Qpt1oa.
Figure6-17. MMT Installer display screen #17
6-18
RevS
FCC ill: CDG-ARTU
EXHIBITC
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
6.3.15 UNLOCKED ONLINE STATE
This step will set the ARTU software executing in an unlocked online state. This command will
change the C-2000 operation from a test mode to an operational mode to allow the installer to
perform normal operational functions.
The MMT display screen will be similar to that shown in Figure 6-18.
Verify that the MMT Radio Responses window displays the following message:
"Radio software executing in unlocked online state".
Type "C" to continue with this test step.
V..~
Ra410a..~
884io 8Of~
_tillg
in ~oc:ke4
~1De
.tat..
Vl& ~
%81&205
Tutorial
a8U'rAa
mrrALLa.UC8
I~~-T%Y.I
Verity
t:!Iat
AR'fV -.
Pl&t into
~oc:ke4/~1De
.tat..
8D8C'1'81)
U8ULTS:
PolloriAg
0 ON8rY8 abo98 -..age
-Ra4io
:ACT%C88I
_..ag.
8Of~.
4i8Played
in
_tiDg
Radio
in ~0cke4
in ~
Ra8P0D8..
~1De
Ra4io a..~..
.tat..
Willdowl
~.
(C)oatiDu.,
Figure 6-18.
(7)roubl.8boot,
(a)epeat,
(Q)ait.
MMT Installer display screen #18.
6-19
RevB
EXHIBffC
FCC ill: CDG-ARTU
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
6.3.16 RECEIVE SIGNAL STRENGTH MEASUREMENT USING GENSTAR GROUND
STATION
This test step will verify the ability of the MagnaStar system to properly monitor a GTE AIRFONE
GenStarTUsystem ground station. This step will use the ARTU to measure the Receive Signal
Strength (RSS) of the Pilot signal from the GenStarTM system ground station. This test will verify
the performance of the aircraft RF interface between the ARTU and the Antenna. (This
measurement is a relative measurement because of the possible RF link variations between the
C-2000 Antenna and the GenStarTUground station). This test is only valid if the test location
will support an RF link with a GenStarTM system ground station.
The installer is to view the MMT Status Updates window and verify that the ARTU has acquired
and is monitoring the pilot signal from a nearby GenStarN ground station. The MMT Status
Updates window will indicate that the ARTU is monitoring a pilot signal by the presence of the
"MON" indication in the "Assignment" row. This indication will be associated with only one of the
ten possible subbands on which pilot signals may be present. If the "MON" indication is not
present, then the ARTU has not acquired the signal from a ground station. In the column below
the "MON" indication the installer will find the associated RSS value in units of demo A value
between -5OdBm and -105 dBm will allow the installer to establish normal communications with
the GenStarTMground station. However, values less than -105 dBm may not constitute a failure.
Because the ARTU is in a normal operational mode when this test is performed. the pilot receiver
will periodically scan each of the ten different subbands searching for the best quality pilot signal
from a ground station. For this reason the reported RSS value may change to a different value
while the pilot receiver is scanning other subbands.
The MMT display screen will be similar to that shown in Figure 6-19.
V&.OA ~
: C-2000
~Z't8
8tatua
update
Pr...
..410 a..paD8e
8A.~-8D
P2 to vi-
sut-
Diaplay
%DUllS
D8AftU
S~reDQth
(U.)
~~ori.l
C-2000 m8'1'Al.l,A.n~
"(8.,~-T~Y.1
Verify
.igDal
~.iY84
f~.
08D8~ar
grcRaDII
.ta~iC8.
:DP~-Tau USUL7S1
U'fU
~r.~iJIQ
."S
(dBa)
0 Pr8..
r2
~o yi-
8)d.
S~.~u.
opcSa~.. wiDdOIf ..
.~
bel~1
1t.1
~t.or
11.1
.~.~U8
11.1
1t.1
aboY8
11.1
S~.~U.
1t.1
11.1
opcSa~..
1t.1
11.1.
wiadow.
: 80~. t:ba~ or ~.
..~~Dd. ~
: .. t:ba~ 8abb8M'. ...1~~
-:
11.1
:Acor%~SI
iD ~~or
.A8.i~~
(C)~~iDD..
8hCJW
u. aDd t:ba~ ,-,
.ill
be 8bo.D
. 8Uitabl. 8abb8M i. loca~e4.
(7)roubl..hoot..
(a)epeat..
(Q)ui~1
Figure 6-19. MMT Installer display screen #19.
6-20
RevB
FCC ill: CDG-ARTU
EXHIBIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
MAGNASTAR
Press the "F2" function key to view the MMT Status Updates window.
The MMT display screen will be similar to that shown in Figure 6-20.
The installer can verify that the ARTUis monitoring the ground station by the
presenceof a "MON" indication in the "Assignment" row of the MMTStatus
Updateswindow.
The installer is to verify that the RSS value of the received pilot signal is greater
than -105 dBm (between -50dBm and -105 dBm) in the column directly below the
"MON" indication. It should be noted that a value less than -105 dBm may not
constitute a failure.
Press the "F1" function key to return to the MMT Status Updates window.
Type "C" to go to the next step.
RSS value
-~
Statu.
Q»dat
(P3..bturn
to
:8IIhbaDd
3.
RaIIk
A8.i~t
ass (488)
Doppler (B8)
0.0
0.0
0.0
0.0
0.0
0.0
0.0
00'r
0U'1'
0U'1'
0U'1'
0U'1'
0U'1'
0U'1'
0U'1'
00'r
3. 8C 0 8C 0 8C 0.:
0.:
0 xa 0 noxa
0.:
0.:
0D
0D
0':
3.
Cell Stat-
Cell Type
TSCA?ail Wt.
Doppler
.t.
TX Power
~sx
30
Wt.
SB 3.:
xa 3. nOD
3.
25
A .
0.0
3.3
58
,,
8ea"..o)
10
0.0
---'
.(9}o.o)
3.3.
Stat8
000000000:
8YDe
('r-'ron1.
3.08
Pree TSC.
.. Path Lo8.
P%I.o'r ftATUS
~ior
0 non
0':
3.5
3. Pilot
20
3.0
A A A A X A A A X A A A X A A A A A A A X A .
: S8 :
:..
,.
..
aav
8tat1l8
3:~
i,
Figure6-20. MMT Installer display screen #20.
6-21
RevB
FCC ID: CDG-ARTU
EXHIB IT C
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
6.3.17 C-2000 INSTALLATION CONCLUSION
The C-2000 Installation testing with the GTE Airfone GenStarTM Ground Station is finished at this
point. Any further installation steps may not require MMT connection to the ARTU. If this is new
installation, the next step is Handset Configuration (Section 7). This step concludes the MMT
Installation by having the installer enter a command to quit the MMT Installation mode.
Quitting the MMT
To quit the MMT at this point. continue with the following steps:
The MMT display screen will be similar to that shown in Figure 6-21.
Type "Q" to quit the MMT C-2000 Installation.
Note: Turn "off'the MMT computer to conserve battery power.
Disconnect the MMT cable from the ARTU.
Reconnect the MMT dust cover to the MMT connector.
Vt.OA
-.T
Radio R..POD
: D8~]"
~.
8'r
VlA ~
Tutorial
C-2000 ~~
orB
CODclude.the 8'r C-2000XD8ta11atiOD.
To QDit the MNT, pr...
'0'
at thi.
t!8e.
To r.-_cut.
the 8'r
Tutorial,
pre..
'c'
at thi.
t~.
(C)ODtiau8,
(7)roQbl..boot,
(a)epeat,
(Q).t~1
Figure 6-21. MMT Installer display screen #21
Re-executinathe MMT
The MMT tutorial may be also be re-executed at this point. If the MMT is to be re-executed,
power to the ARTU must be removed for greater than ten seconds.
The MMT display screen will be similar to that shown in Figure 6.21
Remove power to the ARTU for greater than 20 seconds.
Type "C" to re-execute the MMT C-2000 Installation.
PROGRAMMING THE MAGNAST AR SYSTEM
6-22
RevS
7.1.2.6.4
7.1.2.6.5
7.1.2.6.6
7.1.2.6.7
7.1.2.6.8
7.1.2.7.1
7.1.2.7.2
7.1.2.7.3
7.1.2.7.4
7.1.2.7.5
7.1.2.7.6
7.1.2.7.7
7.1.2.8.1
7.1.2.8.2
7.1.2.8.3
7.1.2.9
7.1.2.10
AIRCRAFT
7.2
7.1.2.8
Aircall
Screens
Attributes
Alerter
and
7-i
Indicators
Cadence
TerminallD
...7-6
...7-6
with
Screens
Aircraft
7.1.2.6.2 Select Aero-H or Aero-l SATCOM Service
7.1.2.6.3 Ringer Enable/Disable
Number
Aircall
Aircraft
an
a SATCOM
Numbers
Mode
CHART
Ringing
Billing
SCREENS
Information
and
FLOW
Session
From
#1
Setup
.".'."""""""""""""""""""""'...'
Passcode
Handset
Pickup
SCREEN
Screen
with
Alerter
the
TerminallD's
Ringing
Call
SATCOM
Settings
(Messages)
Progress
and
In
Switch
Gain
Radio
SATCOM
HF
Handset
Maintenance
Numbers
Call
From
Auxiliary
Register
Call
SHEET
Link
Numbers
and
Aircall
RJ-l1
#2
Screen
Numbers
CONFIGURATION
Menu
a Station
and
Auto
and
Monitor
Gain
Number
Setup
Aircall
Alerter
Programming..
Screen
Setup
TX
Rates
Settings
Call
DTMF
Gains.
Aircall
Gain:
Stored
Programmed
Dial
TCOM
Disabling
Direct
Disabling
Station
Plan
Link
Configuration
Waiting
Configuration
Changing
Inplane
Aircall
SA
Services
Main
Starting
Checking
Maintenance
7.1 HANDSET CONFIGURATION SCREENS
SYSTEM
MAGNASTAR
THE
PROGRAMMING
MAGNASTAR
Availability
Call
Station
Speed
AIU
AIU
Maintenance
Station
Blink
CONFIGURATION
Dialing
Default
Service
MODEM
Handset
Handset
Auxiliary
Speaker
LED
Sidetone
Autodial
Microphone
Personal
Viewing
7.1.2.5.5
Viewing
CONFIGURATION
DETAILED
7.1.2.1
7.1.2.2
7.1.2.3
7.1.2.4
7.1.2.5
7.1.2.5.1
7.1.2.5.2
7.1.2.5.3
7.1.2.5.3.1
7.1.2.5.3.2
7.1.2.5.4
7.1.2.5.4.1
CDBR-2
7.1.2.6.1
Remote
7.1.2.5.6
7.1.2.5.7
7.1.2.5.8
7.1.2.6
7.1.1
7.1.2
7.0
FCC ill: CDG-ARTU
EXHIBIT C
C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
TerminallD
7-1
7-1
7-1
7-S
7-S
7-S
...7-7
...7-7
...7-8
...7-9
.7-10
.7-10
.7-11
.7-11
.1-12
.7-12
.7-12
.1-13
.7-13
.7-1S
.7-1S
.7-16
.1-16
.7-16
.7-17
.7-18
.7-18
.7-19
.7-19
.7-20
.7-20
,7-21
7-21
7-23
7-23
7-23
7-23
7-2S
7-25
7-26
7-22
RevB
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2002:07:01 16:17:20Z Modify Date : 2002:07:17 13:56:36-05:00 Page Count : 27 Producer : Hewlett-Packard Intelligent Scanning Technology.3 Author : tjdrew [ TJDREW ] Creation Date : 2002:07:01 16:17:20Z Mod Date : 2002:07:17 13:56:36-05:00 Metadata Date : 2002:07:17 13:56:36-05:00 Creator : tjdrew [ TJDREW ] Has XFA : NoEXIF Metadata provided by EXIF.tools