Silex Technology SX10WAG SX-10WAG User Manual Manual

Silex Technology, Inc. SX-10WAG Manual

Manual

July 10,2006
1. Hardware specifications/Compliance・・・・・・・・・・・・・・・・・・・・2
2．System Requirements・・・・・・・・・・・・・・・・・・・・・・・・・・・4
3．Setup ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・4
SX-10WAG Users Manual
SX-10WAG Users Manual
silex technology,lnc.
１
FCC ID：N6C-SX10WAG
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and
meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment
should be installed and operated with at least 20cm and more between the radiator and person’s body
(excluding extremities: hands, wrists, feet and legs).
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation
FCC WARNING：
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Canada
『This device complies with Part 15 of the FCC Rules and RSS-Gen of the IC
Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.』
1 Hardware specifications/Compliance
SX-10WAG Users Manual
silex technology,lnc.
2
Operating environment ： Temperature：+0°C to +60°C, +32F to +140F
Humidity：20% to 90%
Storage environment ： Temperature：-10°C to +70°C, +14F to +158F
Humidity：5% to 90%
supply voltage ： 3.3V ± 0.3V
Host I/F ： MiniPCI
IEEE802.11b ： Frequency : 2412MHz~2462MHz
Transmission system ： DS-SS
Transmission speed： 1M/2M/5.5M/11M
Automatic detection
Channel：1−11ch
IEEE802.11g ： Frequency : 2412MHz~2462MHz
Transmission system：OFDM
Transmission speed ：6M/12M/18M/36M/48M/54M
Automatic detection
Channel：1−11ch
IEEE802.11a ： Frequency : 5180MHz~5320MHz 5745MHz~5825MHz
Transmission system：OFDM
Transmission speed ：6M/12M/18M/36M/48M/54M
Automatic detection
Channel：36−64ch 149−165ch
Antenna interface ： Diversity connector
SX-10WAG Users Manual
silex technology,lnc.
3
PC containing:
. 32-bit CardBus slot (or Desktop PC with PC Card-PCI adapter)
. Mini PCI
. 32 MB memory or greater
. 300 MHz processor or higher
When this module is installed in the host product, you must include a "Contain FCC ID : N6C-SX10WAG"
in the label of the host product.
It uses Driver and a utility of Atheros Communications. （Atheros client utility）
It completes installation according to setup Wizard
silex technology,lnc.
SX-10WG Users Manual
６
SX-10WAG Users Manual
silex technology,lnc.
4
System Requirements
(
for the install
)
3 Setup

Navigation menu