Boston Scientific Neuromodulation SC5232 SC-5232 User Manual 90668562 01 falconmanual en v8 indd
Boston Scientific Neuromodulation Corporation SC-5232 90668562 01 falconmanual en v8 indd
Contents
Additional User Manual 8
Adjust Screen Brightness ...........................................43
Adjust Volume ..........................................................44
View Information about Your Remote Control or
Stimulator .................................................................45
About System Settings
Page 42
Precision Spectra™ Remote Control Handbook, 90668562-03, Rev C
Using the System Settings , you can set or change a
few RC interface settings, such as the Alert Volume ,
Screen Brightness , and the Language setting .
In addition, you can view information about the RC
and the Stimulator . Your healthcare provider can
access special functions through the Clinician Menu
(password protected) to aid you in your therapy.
Remote Settings
Alert Volume
Screen Brightness
Languages
SelectBack
About System Settings
SYSTEM SETTINGS
Page 43
Precision Spectra™ Remote Control Handbook, 90668562-01, Rev C
System Settings
Remote Settings
System Info
Clinician Menu
SelectBack
Remote Settings
Alert Volume
Screen Brightness
Languages
SelectBack
1 3
Programs
Stimulation Areas
Main Menu
System Settings
SelectBack
P
From the Main
Menu , select
System Settings .
Select Remote
Settings by
pressing .
Select Screen
Brightness by
pressing .
2
Screen Brightness
Back
4/5
To decrease or
increase Screen
Brightness, press the
or the button.
Adjust Screen Brightness
Precision Spectra™ Remote Control Handbook, 90668562-03, Rev C
System Settings
Remote Settings
System Info
Clinician Menu
SelectBack
Remote Settings
Alert Volume
Screen Brightness
Languages
SelectBack
1 3
Programs
Stimulation Areas
Main Menu
System Settings
SelectBack
P
From the Main
Menu , select
System Settings .
Select Remote
Settings by
pressing .
Select Alert
Volume by
pressing .
2
Alert Volume
Back
4/5
To increase or decrease
screen volume, press the
or the button.
The RC emits a single, short Alert that sounds like a “beep” whenever you press
a button. The volume of the Alert can be adjusted or turned off.
Adjust Volume
Page 44
Precision Spectra™ Remote Control Handbook, 90668562-01, Rev C
e
System Settings
Remote Settings
System Info
Clinician Menu
SelectBack
SelectBack
System Info
Remote Info
Stimulator Info
1 3a
Programs
Stimulation Areas
Main Menu
System Settings
SelectBack
P
From the Main
Menu , select
System Settings .
Select System
Info by
pressing .
Select Remote Info
by pressing .
2
SelectBack
System Info
Remote Info
Stimulator Info
3b
Select Stimulator Info
by pressing .
You can view basic information about your RC and Stimulator that may be
helpful for your healthcare provider when troubleshooting an issue.
OR
View Information about Your Remote Control or Stimulator
SYSTEM SETTINGS
Page 45
Page 46
Precision Spectra™ Remote Control Handbook, 90668562-03, Rev C
This page intentionally left blank.
Save Changes Screen ................................................48
Battery Low and Recharge Messages .........................49
Charging Remote Screen ..........................................51
Charger Disconnected Screen ...................................51
Remote Battery Full Screen ........................................52
Button Stuck .............................................................52
End of Programmed Service ......................................53
Reminders and Messages
Page 48
Precision Spectra™ Remote Control Handbook, 90668562-01, Rev C
The Save Changes confirmation screen will appear under the following conditions:
• One or more changes have been made to the Program currently running, including:
changes in stimulation strength (on the Home Screen), changes to any of the
Stimulation Area parameters AND…
• The Program that is running is about to be changed to a different Program. This can
occur when selecting either Change Programs or Restore to Clinic Settings
from the Programs Menu.
If you want to save the change(s), select Yes – Save . These settings will be the
default settings the next time this Program is selected to be run.
If you do not want to save the change(s), select No – Discard. The original Program
settings will be maintained and any change(s) will be discarded. The RC will then
proceed to the function that you selected – either Change Programs or Restore to
Clinic Settings .
Save Changes Screen
REMIND/MESSAGE
Page 49
Precision Spectra™ Remote Control Handbook, 90668562-01, Rev C
The RC will provide on-screen
messages to remind you when your
Stimulator and RC batteries are low.
For the Implant, the following on-
screen messages display:
For instructions on recharging the
Implant, refer to your
Charger
Handbook.
For the Trial Stimulator, the following
on-screen messages display:
For instructions on replacing your
Trial Stimulator batteries, refer to your
Patient Trial Handbook.
Low
Stimulator
Battery
Press to continue
Charge
Stimulator
Now
Press to continue
Battery Low and Recharge Messages
Replace
Battery
Now
Press to continue
Press to continue
Low
ETS
Battery
ETS = Trial
Stimulator
Page 50
Precision Spectra™ Remote Control Handbook, 90668562-01, Rev C
For the RC, the following on-screen
messages display:
Refer to Recharging the Remote
Control page 16 of this handbook
for more information on charging your
RC.
Charge
Remote
Now
Press to continue
Low
Remote
Battery
REMIND/MESSAGE
Page 51
Precision Spectra™ Remote Control Handbook, 90668562-01, Rev C
This screen is displayed when the RC is
being used and the USB power supply is
plugged in.
This screen is displayed when the RC is
being used and the USB power supply
is disconnected.
Charging
Remote
Charger
Disconnected
Charging Remote Screen Charger Disconnected Screen
Page 52
Precision Spectra™ Remote Control Handbook, 90668562-01, Rev C
This screen is displayed when the
RC is being used and the RC battery
becomes fully charged.
If a button is stuck on the RC, other
button presses may not function as
intended. The RC will provide the
following on-screen message if it
detects a stuck button:
Please attempt to resolve the stuck
button in order to restore proper
functionality of the RC.
Remote
Battery
Full
Remote Battery Full Screen Button Stuck
REMIND/MESSAGE
Page 53
Precision Spectra™ Remote Control Handbook, 90668562-01, Rev C
Your Stimulator software has been
programmed to end service after a
defined period. When your Stimulator
is within approximately 180 days of
the end of its programmed period, the
RC will display the following on-screen
message:
Press to clear the message. The
message will reappear approximately
weekly until the end of the Stimulator’s
programmed period is reached. When
the end of its programmed period
is reached, the RC will display the
following on-screen message:
~180
Remaining days
of service
Press to continue
Stimulator
Service
Exceeded
End of Programmed Service
Page 54
Precision Spectra™ Remote Control Handbook, 90668562-01, Rev C
This page intentionally left blank.