Contents
Manual 3
7
Fujitsu F905i i-mode 3.5G
UMTS 2100 GSM 900/1800/1900
Thank you for purchasing Fujitsu F905i mobile terminal.
Both before and during use of your F905i mobile terminal, be sure to thoroughly read this manual
to ensure you are able to correctly use your F905i mobile terminal. For more information, you may
contact FarEastTone Customer Service, as mentioned at the end of this manual.
Treated with care, your F905i mobile terminal will be your able partner.
Before using your terminal
• Some of the services described in this manual may not be supported by all networks. Please
contact your network operator to confirm whether you can use or not a particular service.
• F905i terminal is intended to be used with FarEasTone SIM/USIM card, and we do not make any
warranty for the F905i terminal when used with a SIM/USIM card provided by someone other
than FarEasTone.
• F905i terminal is compatible with i-mode service. This service supports connection to i-mode
sites (programs) or i-mode compatible sites that provide a variety of useful information and
allows you to exchange i-mode mail. i-mode is an optional service requiring subscription to your
network operator FarEastTone.
• F905i terminal supports HSDPA (High-Speed Downlink Packet Access) technology, allowing to
perform high-speed communication with a receiving speed of up to 3.6 Mbps and a sending
speed of up to 384 Kbps. Note that HSDPA is supported by F905i terminal only when operating
on FarEasTone network, in the area providing HSDPA service.
• Your phone supports emergency numbers, such as 112, which allow to make emergency calls
with or without a SIM/USIM card inserted, if a 3G (UMTS) or GSM network is within range.
However emergency calls may not be possible on all mobile phone networks, or when certain
network services or phone features are in use. You should therefore never rely solely upon any
mobile phone for essential communications, such as medical emergencies.
• Because your terminal uses radio waves, it may not function in locations where it is difficult for
radio waves to penetrate, such as tunnels, underground passages and some buildings, in areas
where radio wave signals are weak, or out of service area. Even when you are high up in a tall
building or condominium and nothing blocks your view outside, your terminal may not be able to
receive or transmit signals. Also, communication may be interrupted even when the signal meter
on your terminal indicates there is a strong signal.
3+4DQQM2CIG9GFPGUFC[#RTKN2/
8
• The terminal has a built-in antenna located near the fingerprint sensor. Do not cover the antenna
with your hand when the phone is in use, since this may reduce call quality and may cause the
handset to operate at a higher power level than needed, thus shortening call and standby times.
• Your terminal encodes voice communication as digital data. When you are operating your
terminal while moving to a location subject to weaker radio wave signals, the transmitted digital
data may not be correctly decoded and as a result the decoded voice may differ somewhat from
the actual voice.
• Use your terminal in a way that does not disturb others in public spaces, crowded locations or
quiet places.
• Maintain a separate record of the data (Phonebook, Schedule, Notepad, Recorded messages,
Voice memos, Movie memo, etc.) you registered in your terminal. You are recommended to save
important data to microSD card (A microSD card is required. If you have none, purchase it in an
electric appliance store). Using the PC software contained in the CD-ROM for F905i terminal, you
can also transfer and save phonebook, mail and some other data to a PC.
Note that we assume no responsibility for any loss of saved contents or data resulting from
malfunction, repair, changing of the model or other handling of the F905i terminal. In addition,
Fujitsu assumes no responsibility for third-party applications and for contents or data
downloaded from the network. We do not endorse liability for preinstalled bookmarks and links to
third-party internet sites.
• The user hereby agrees that the user shall be solely responsible for the result of the use of SSL.
Neither Fujitsu nor the certifier as listed herein makes any representation and warranty as for the
security in the use of SSL. If the data should be erased, we assume no responsibility for the loss
of any data.
Certifiers : VeriSign Japan K.K., GlobalSign K.K., Verizon Business Security Solutions Powered
by Cybertrust, TC TrustCenter GmbH, Entrust, Inc.
A detailed User Manual is provided in the CD-ROM for F905i terminal. Please refer to it for more
complete information about how to use your terminal.
Information contained in this manual is the property of FUJITSU LIMITED. Unauthorized copying of
parts of or this entire manual is prohibited.
This manual is published by Fujitsu without any warranty. The images or illustrations provided in
this manual are for information purposes only and may differ from the actual displays. The contents
of this manual and product specifications are subject to change without prior notice.
3+4DQQM2CIG9GFPGUFC[#RTKN2/
9
Precautions
(ALWAYS FOLLOW THESE
DIRECTIONS)
• Before using your F905i terminal, or when
necessary, read the precautions below to
ensure safe use and handling. After reading
this manual, keep it carefully.
• These precautions are intended to protect
you and others around you. Read and follow
them carefully to avoid injury, damage to the
product or damage to property.
❖Handling F905i terminal,
battery pack, AC adapter and
SIM/USIM card (Common)
DANGER
Do not use, store, or leave the equipment in
hot areas such as near flames or in areas
under strong direct sunlight such as inside
a vehicle.
May cause the equipment to be deformed or
malfunction, and battery pack to leak, heat,
burst or ignite, and the capability or life to be
reduced or shortened. Overheating on parts of
the case may cause burns or injuries.
Do not disassemble or remodel the
equipment. Do not solder items onto the
equipment.
May cause fire, injuries, electric shock, or
malfunction. It may also cause the battery
pack to leak, heat, burst or ignite.
Any changes or modifications not expressly
approved by Fujitsu could void the user's
authority to operate this equipment and
invalidate the terminal's certification of
technical standard compliance.
Do not tamper or remove any inscription
stickers attached to the terminal, since these
inscription stickers certify that the terminal
satisfies specific technical standards.
Never open, modify or repair your phone
yourself. Repair shall be performed by
authorized personnel only.
Keep water and other liquids away from
F905i terminal, battery pack, AC adapter
and SIM/USIM card.
F905i terminal, battery pack, AC adapter and
SIM/USIM card are not waterproof. Contact
with water or other liquid can cause heating,
electric shock, fire, malfunctions or injuries.
Do not use F905i terminal in bathrooms or
other high-humidity areas, or in the rain. When
carrying the terminal in a pocket near your
body, sweat may corrode the inner
components, causing malfunction.
Malfunctions deemed to be caused by water
or by other liquid are not covered by the
warranty, and may be impossible to repair.
Use only battery pack, AC adapter and
accessories specified and approved by
Fujitsu for this particular model.
The use of any other types would invalidate
any approval or warranty, may damage the
equipment, and may be dangerous.
* The list of compatible accessories for F905i
can be found Page 22.
3+4DQQM2CIG9GFPGUFC[#RTKN2/
10
WARNING
Do not put the battery pack, F905i terminal,
AC adapter or SIM/USIM card in microwave
ovens or other heating appliances or high-
pressure containers.
May cause the battery pack to leak, heat, burst
or ignite, the F905i terminal, AC adapter or
SIM/USIM card to heat, smoke, ignite, or
damage circuits.
Do not throw the equipment, or give hard
shock or excessive force to the terminal or
the battery.
May cause the battery pack to leak, heat, burst
or ignite, and the equipment to be damaged,
malfunction or catch fire.
Keep conductive materials (metal pieces,
pencil lead, etc.) away from coming in
contact with the charging connectors or the
earphone/microphone jack. Do not put
those materials inside the terminal.
May be subject to electrical short and could
cause fire or malfunction.
Turn the terminal OFF before entering a
place such as a gas station where
flammable gases are generated. Do not
charge the battery. The gas may catch fire.
If the equipment starts giving off a strange
smell, overheats, becomes discolored or
deformed during use, charging or in
storage, immediately perform the following
operations:
1 Remove the power plug from the wall
outlet.
2 Turn the F905i terminal OFF.
3 Remove the battery pack from the
terminal.
CAUTION
Do not leave the equipment on unstable or
sloping surfaces.
Do not store the equipment in extremely
humid, dusty or hot areas.
May cause malfunction.
Do not place the equipment near an air-
conditioner outlet.
The rapid change in temperature may cause
condensation, causing internal corrosion and
malfunction.
Children using the equipment should be
instructed in proper operation by an adult.
Do not allow them to use the equipment
without adult supervision.
Store the equipment out of reach of small
children.
The equipment can be accidentally swallowed
or cause injuries.
Be careful especially when using the F905i
terminal connected to the AC adapter
continuously for a long time.
If you execute i-αppli, use videophone call,
etc. while charging the battery pack, the F905i
terminal, battery pack and AC adapter may
become hot. Directly touching a hot part for a
3+4DQQM2CIG9GFPGUFC[#RTKN2/
11
long time, you may have redness, itching or
rash on your skin, or it may result in low-
temperature burns.
For your information, it is normal for F905i
terminal, AC adapter and SIM/USIM card to
become warm during use or charging:
continue to use them.
❖Handling F905i terminal
WARNING
Avoid temperature extremes.
Use the terminal in an ambient temperature
range of between 5 and 35Åé, and in a
humidity range of between 45 and 85%.
Do not direct the infrared data port toward
your eye and transmit signals.
May affect your eyes. Faulty operation could
result from directing the infrared data port
toward other infrared equipment and
transmitting signals.
Do not put the F905i terminal in the place
such as the dashboard near the airbag,
where the influence of air-bag explosion is
expected.
When the air-bag explodes, the terminal may
hit yourself or others and could cause injury,
equipment malfunction or damage.
When you use medical electrical equipment,
do not keep the terminal in your chest
pocket or inside pocket.
Using your terminal near medical electronic
equipment could cause equipment failure.
Do not put foreign objects such as liquid
like water, metal pieces or burnable things
into the SIM/USIM card or memory card slot.
May cause fire, electric shock or equipment
failure.
Do not turn on the light aiming directly at
the driver of the car, etc.
It hinders driving, and may result in an
accident.
Turn the terminal OFF in areas where use is
prohibited, such as in airplanes and
hospitals.
Use in these areas can cause electronic
medical equipment and electronic equipment
to malfunction or fail.
If the function which automatically turns on the
power is set, cancel the setting before turning
the power off.
When using the phone in a medical facility, be
sure to observe the regulations of the facility.
Switch off your phone when boarding an
aircraft or whenever you are instructed to do
so by airline staff. Current legislation forbids
the use of mobile phones on board and legal
action can be taken against the user.
Do not use the phone while driving.
Before making or answering a call, pull off the
road and park at a safe place.
When the speaker is in use (for example
when the ring alert is sounding or when you
are talking or playing a melody by setting
hands-free), always keep the terminal away
from your ear. And, when listening to music
or playing a game, or when connecting the
remote controller with stereo earphone
3+4DQQM2CIG9GFPGUFC[#RTKN2/
12
interface and microphone to the terminal,
adjust the volume to a moderate level.
Too loud volume may cause a hearing loss.
And, if you cannot hear the sound around you
clearly, it may cause an accident.
If you have weak heart, be careful when
setting the Vibrate alert (vibration) or alert
volume setting.
Could affect heart function.
If it starts thunder while using the phone
outside, turn the power OFF immediately,
and move to a safe location.
May be subject to lightning strike and could
cause electric shock.
Turn the terminal OFF near high-precision
electronic control equipment or electronic
equipment using low-power signals.
Using the phone near this type of equipment
can cause the equipment to fail or malfunction.
* Examples of electronic equipment to avoid:
Hearing aids, implanted pacemakers or
defibrillators, other electrical medical
equipment, fire alarms, automatic doors, other
automatic control equipment. Users wearing
implanted pacemakers or defibrillators or other
electrical medical equipment should check
with the manufacturer or sales outlet about the
effect of radio frequencies on the equipment.
When the display or camera lens is
accidentally broken, be careful of broken
glass or exposed internal parts of the
terminal.
Surfaces of display and camera lens are made
of plastic panels and they are structured for
the glass not to scatter, however, if you
mistakenly touch broken or exposed parts, you
may be injured.
CAUTION
Clean the terminal with a dry soft cloth
(such as a cloth for eyeglasses).
Drops of water or dirt left on the display can
cause stains or remove the coating. If the
terminal is wiped with alcohol, paint thinner,
benzene or detergent, the printing may
disappear or color may fade.
Clean the jack occasionally with a dry
cotton swab.
If the jack is dirty, the contact may become
poor and the power may shut off. A dirty jack
can result in poor charging, so clean it with a
dry cloth or cotton swab.
Do not swing the terminal by its strap, if
any.
May cause the terminal damage or failure, or
injury to yourself or others.
Do not place magnetic disks or cards with
magnetic stripes near the terminal or place
inside and fold the terminal.
Data stored on media such as cash cards,
credit cards, telephone cards and floppy disks
may be erased if the storage medium is
placed near the phone.
Do not bring magnetized objects close to
the terminal.
Bringing strong magnetism close may cause a
malfunction.
3+4DQQM2CIG9GFPGUFC[#RTKN2/
13
Do not plug external device into the
charging connector or the earphone/
microphone jack at a slant, or do not pull it
forcibly while it is plugged.
Malfunction or breakage may result.
Use the terminal with the earphone/
microphone jack cover, the charging
connector cap and the memory card slot
cover placed.
Dust or water brought into the terminal cause
troubles.
Do not use the terminal with the back cover
removed.
It may cause the battery to come off, or may
cause a malfunction or damage.
If the display part is accidentally broken and
liquid crystal leaks out, do not put the liquid
in your mouth, inhale, or make contact with
your skin. If the liquid gets into your eyes or
mouth, rinse it with clean water and see a
doctor immediately. And, if the liquid
adheres to skin or clothing, use alcohol,
etc. to wipe it off, then wash with soap.
Do not rub or scrape the display with a
metal piece, etc.
It may scratch the display, causing
malfunction or damage.
Do not put a extremely thick seal, etc. on
the display or keypad.
May cause malfunction.
Do not rotate the display with the terminal
folded.
It may cause the display and around the keys
to be scratched, causing a malfunction or
damage.
Do not give a hard shock to the fingerprint
sensor and take care not to scratch its
surface.
May cause the fingerprint sensor to
malfunction or disable authentication.
Clean the fingerprint sensor by wiping with
a dry soft cloth (e.g. eyeglass cleaner).
Any soil or water attached to the surface of the
fingerprint sensor may cause fingerprint scan
failure, which may lead to reduction of the
authentication performance or an error where
the sensor operates as authenticating when
the finger is not in contact.
While using memory card, do not remove
memory card or turn OFF the terminal.
It may cause data loss or malfunction
* A memory card is required separately. You
can purchase it in an electric appliance store.
The terminal may affect general subscriber
phones, TVs or radios in use nearby, so use
it as far as possible from these appliances.
In rare cases, using the phone in some
vehicle models can cause the vehicle's
electronic equipment to malfunction or fail.
In this case, do not use the phone because it
may hamper safe driving.
Mobile phones can give some users skin
problems such as itching, allergic reactions
or rashes. If you develop skin problems,
stop using the phone immediately, and see
a doctor.
3+4DQQM2CIG9GFPGUFC[#RTKN2/
14
When opening or closing the terminal, take
care not to have your fingers or strap
caught by the terminal.
Do not fold the terminal with the strap held
inside
During extended operation (such as video
watching), take a certain distance from the
display in a fully bright place.
May cause your eyesight to be impaired.
The display may have afterimages.
If the battery pack is removed from the
terminal before the terminal power is turned
off, afterimages may remain. Remove the
battery pack with the power turned OFF. If the
terminal is left open for a while with the same
screen displayed, afterimages of that screen
may remain even after changing the screen for
a certain operation.
DISPOSAL OF MOBILE PHONE
AND ELECTRICAL
ACCESSORIES
To preserve the environment, electrical and
electronic equipments shall not be treated as
household waste. You shall always obey the
rules and regulations defined locally for
recycling electrical and electronic equipments.
For more information, please contact your local
waste disposal service, or the shop where you
purchased your F905i terminal, or contact
FarEastTone Customer Service.
❖Handling battery pack
Use solely the battery pack approved by
Fujitsu for this particular model.
DANGER
Do not connect a wire or other metal
objects to the jack. And, do not carry or
store the F905i terminal with objects like a
metal necklace.
May cause the battery pack to leak, heat, burst
or ignite.
Do not try to force the battery pack onto the
F905i terminal if you are having trouble
attaching it. Always attach it after checking
that it is correctly oriented.
May cause the battery pack to leak, heat, burst
or ignite.
Do not throw the battery pack into the fire.
May cause the battery pack to leak, heat, burst
or ignite.
Do not nail the battery pack, hit with a
hammer or step on it.
May cause the battery pack to leak, heat, burst
or ignite.
If the battery pack's fluid contacts eyes,
immediately flush the eyes with clean water
and see a doctor right away. Do not rub the
eyes.
Battery fluid in the eyes may cause blindness.
3+4DQQM2CIG9GFPGUFC[#RTKN2/
15
WARNING
Charge the battery in an area within the
proper ambient temperature range (5-35ºC).
Do not charge a wet battery pack.
It may cause heat generation, ignition or
rupture of the battery pack.
Do not charge the battery in the areas below :
- In areas of excessive humidity, dust or
vibrations
- Near general subscriber phones, TVs or
radios
If the battery pack's fluid contacts skin or
clothes, immediately flush the contacted
area thoroughly with clean water.
The fluid may damage the skin.
If the battery pack does not have a full
charge after being charged for the specified
time, stop charging it.
May cause the battery pack to leak, heat, burst
or ignite.
If the battery pack leaks or gives off a
strange smell, immediately remove it from
the vicinity of open flames.
The vapors from leaking battery pack fluid may
ignite or explode.
If the battery pack seems to have
abnormalities such as deformation or
scratches due to an external impact or
falling, stop using it immediately.
Be careful not to let your pet bite the battery
pack.
May cause the battery pack to leak, heat, burst
or ignite, and the equipment to malfunction or
catch fire.
CAUTION
Always charge before using the battery
pack for the first time or after extended
disuse
The battery pack is a consumable part and
the operation time provided by the battery
pack varies by the operating environment
and battery pack's deterioration.
Each time the battery pack is charged, time
available with each charging reduces. When a
time available with each charging is reduced
to about a half from that of a new battery,
replacement of the battery is recommended
because it is near the end of life.
Note that the battery pack's life may be
reduced by using i-αppli or videophone while
charging.
The battery pack may swell out as it comes to
near the end of its lifetime depending on the
usage conditions, but it is not a problem.
Do not preserve or leave the battery pack as
it is empty.
It may cause the battery pack performance to
be degraded or its lifetime to be shortened.
For better battery pack performance.
Do not charge the battery for an extended
period (several days) with F905i terminal
turned ON. After charging has completed with
F905i terminal turned ON, the power is
3+4DQQM2CIG9GFPGUFC[#RTKN2/
16
supplied to the terminal from the battery pack.
If the terminal is left in that state for a long time,
the battery pack may run out causing the low
battery alert to sound after using only a short
period of time. In such a case, remove the
terminal from the AC adapter and then
reconnect it and charge the battery again.
DISPOSAL OF BATTERY
To preserve the
environment, battery packs
shall never be disposed with
the household waste. You
shall always obey the rules
and regulations defined
locally for recycling batteries.
Dispose an old battery pack in a dedicated
battery disposal facility, if any, or bring it to the
shop where you purchased your F905i
terminal.
For more information, please contact your local
waste disposal service, or the shop where you
purchased your F905i terminal, or contact
FarEastTone Customer Service.
❖Handling AC adapter
Use solely the AC adapter approved by
Fujitsu for this particular model.
WARNING
Do not use the power adapter cord if it gets
damaged.
May cause electric shock, heat or fire.
Do not use the AC adapter in a bathroom or
other highly humid area.
May cause electric shock.
When it starts to thunder, do not touch the
F905i terminal and AC adapter.
May be subject to lightning strike and could
cause electric shock.
Do not short-circuit the charging
connectors or the AC adapter while it is
connected to the outlet. Do not touch the
charging connectors or the AC adapter with
a part of your body such as your hand or
finger.
May cause fire, malfunction, electric shock or
injuries.
Do not place heavy objects on the power
adapter cord.
May cause electric shock or fire.
Do not touch the power adapter cord or
outlet with wet hands.
May cause electric shock.
Only use with the specified power source
and voltage.
If incorrect voltage is used, this may cause fire
or failure.
Wipe off any dust that accumulates on the
power plug.
May cause fire.
When you connect the AC adapter to an
outlet, make sure not to touch with metal
such as metal straps and firmly connect to
the outlet.
May cause electric shock, electrical short or
Please recycle
used batteries
3+4DQQM2CIG9GFPGUFC[#RTKN2/
17
fire.
When you disconnect the AC adapter from
the outlet, do not pull the cord with
excessive force; instead hold the plug to
disconnect.
Pulling the cord could damage it, possibly
leading to electric shock or fire.
Always remove the power plug from the
outlet when not using the AC adapter for an
extended period.
May cause electric shock, fire or malfunction.
Immediately remove the power plug from
the outlet if water or other fluids get into the
AC adapter.
May cause electric shock, smoke or fire.
When using an outlet with a mechanism
preventing unplugging, follow the handling
instructions for that outlet.
CAUTION
Do not deform or give hard shock to the AC
adapter and the charging connectors.
May cause malfunction.
❖Handling SIM/USIM card
F905i terminal is intended to be used with
FarEasTone SIM/USIM card, and we do not
make any warranty for the F905i terminal
when used with a SIM/USIM card provided
by someone other than FarEasTone.
CAUTION
Maintain a separate record of the data you
register on the SIM/USIM card.
If the data should be deleted, we assume no
responsibility for the loss of any data.
Note that we assume no responsibility for
malfunctions occurring as the result of
inserting and using a SIM/USIM card with
another IC card reader/writer.
Avoid temperature extremes.
Clean the SIM/USIM card with a soft, dry
cloth (such as a cloth for eyeglasses).
Always keep the IC clean.
Do not use excessive force to insert/remove
the SIM/USIM card.
Take care not to scratch, touch accidentally
or short-circuit IC.
May cause data loss or malfunction.
Do not drop the SIM/USIM card or subject it
to shocks.
May cause malfunction.
Do not bend the SIM/USIM card or place
heavy objects on it.
May cause malfunction
Do not insert the SIM/USIM card into the
terminal with a label or sticker put on the
SIM/USIM card.
May cause malfunction.
To preserve the environment, bring the old
3+4DQQM2CIG9GFPGUFC[#RTKN2/
18
SIM/USIM card to a sales outlet such as the
shop where you purchased your F905i
terminal.
❖Handling mobile phones
near electronic medical
equipment
WARNING
Obey the following rules inside medical
facilities:
• Do not bring the F905i terminal into operating
rooms (ORs), intensive care units (ICUs) or
coronary care units (CCUs).
• Turn the terminal OFF in hospital wards.
• Turn the terminal OFF in hospital lobbies and
corridors if electrical medical devices could
be nearby.
• If the medical facility has specified zones
where use or possession of mobile devices
is prohibited, obey those instructions.
• If the function to automatically turn on the
power is set, cancel the setting before
turning the power off.
Turn the F905i terminal OFF in crowded
trains or other public places where
pacemaker or defibrillator wearers could be
nearby.
The terminal's signals may affect the operation
of implanted pacemakers or defibrillators, and
other devices.
Wearers of implanted pacemakers or
defibrillators must carry and use the F905i
terminal at least 22 cm away from the
implanted device.
The terminal's signals may affect the operation
of implanted pacemakers or defibrillators, and
other devices.
When electrical medical devices other than
implanted pacemakers or defibrillators are
in use outside of medical facilities (such as
in home care settings), check with the
device manufacturer to determine how the
device is affected by electrical signals.
The terminal's signals may affect the
performance of electrical medical devices.
Intellectual property rights
❖Copyrights and portrait
rights
Except for the cases protected by copyright
laws such as personal use, use of your
terminal to reproduce, alter, sell or redistribute
recorded pictures or sounds, or copyrighted
text, images, music or software downloaded
from Internet or i-mode sites without the
copyright holder's authorization is prohibited.
Fujitsu assumes no responsibility for the
quality and use of any downloaded contents,
and of any other third party content and
application. We do not endorse liability for
preinstalled bookmarks and links to third-party
internet sites.
Note that taking photos or recordings at some
demonstrations, performances or exhibitions
3+4DQQM2CIG9GFPGUFC[#RTKN2/
19
may be prohibited even when only for personal
use. Avoid taking pictures of others with your
terminal without their consent or disclosing
recorded pictures of others without their
consent to general public (through Internet
websites, etc.), because they may infringe on
portrait rights.
❖Trademarks
Company and product names mentioned in
this manual are trademarks or registered
trademarks of their respective holders.
• "i-motion", "i-mode", "i-αppli", "i-motion mail",
"i-shot", "Short Mail", "Chaku-motion (Movie
ringtone)", "Deco-mail", "Chara-den", "i-
αppliDX" and "Chokkan Game" and logos of
"i-mode", "i-Éøppli" and "DCMX" are
trademarks or registered trademarks of NTT
DoCoMo.
• Microsoft®, Windows®, Windows Vista™
Windows Media® and PowerPoint® are
trademarks or registered trademarks of
"Microsoft Corporation" in the U.S. and other
countries.
• Microsoft Excel and Microsoft Word are
product names of Microsoft Corporation in
the U.S.A. In this manual, they may be
described as Excel and Word.
• Java and all Java-related trademarks are
trademarks or registered trademarks of Sun
Microsystems, Inc. in the U.S. and other
countries.
• "Multitask" is a trademark of NEC
Corporation.
• ACCESS and NetFront are
trademarks or registered
trademarks of ACCESS
CO., LTD. in Japan and other countries.
Copyright© 1996-2008 ACCESS CO., LTD.
• Contains Flash® Lite™ and Adobe®
Reader® technology by Adobe Systems
Incorporated.
Flash Lite copyright© 1995-
2008 Adobe Macromedia
Software LLC. All rights
reserved.
Adobe Reader copyright©1984-2008 Adobe
Systems Incorporated. All rights reserved.
Adobe, Flash, Flash Lite and Reader are
either registered trademarks or trademarks
of Adobe Systems Incorporated in the United
States and/or other countries.
• FlashFX® Pro™ is a registered trademark of
DATALIGHT, Inc. FlashFX® Copyright 1998-
2008 DATALIGHT, Inc. U.S. Patent Office
5,860,082/6,260,156
• QR code is a registered trademark of Denso
Wave Inc.
• miniSD™ and are trademarks of the
SD Association. (miniSD™ memory card is
described as miniSD memory card.)
• microSD logo is a trademark.
• Powered by JBlend™
Copyright 2002- 2008 Aplix
Corporation. All rights
reserved.
JBlend and JBlend-related trademarks are
trademarks or registered trademarks of Aplix
Corporation in Japan and other countries.
3+4DQQM2CIG9GFPGUFC[#RTKN2/
20
• Word, Excel and PowerPoint
file display technologies are
powered by Picsel Technologies.
Picsel, Picsel File Viewer and the Picsel cube
logo are trademarks or registered
trademarks of Picsel Technologies, Picsel
File Viewer.
• QuickTime is a registered trademark of
Apple Inc. in the U.S. and other countries.
• This product contains software licensed by
Symbian Software Ltd. © 1998-2008.
and Symbian OS are trademarks
of Symbian Ltd.
• "Privacy mode" is a registered trademark of
FUJITSU LIMITED.
• Google is a registered trademark of Google
Inc.
• T9 is a trademark or
registered trademark of
Nuance Communications,
Inc. or its affiliates in the
United States and/or other countries.
T9® Chinese Text Input is licensed under
one or more of the following:
U.S. Pat. Nos. 5,187,480, 5,818,437,
5,945,928, 5,953,541, 6,011,554, 6,286,064,
6,307,548, 6,307,549, and 6,636,162,
6,646,573, 6,970,599; Australia Pat. Nos.
727539, 746674, 747901; Austria Pat. Nos.
AT225534, AT221222; Brazil P.I. No.
9609807-4; Canada Pat. Nos. 1,331,057,
2,227,904, 2,278,549, 2,302,595; Japan Pat.
Nos. 3532780, 3492981; United Kingdom
Pat. No. 2238414B; Hong Kong Standard
Pat. No. HK1010924; Republic of Singapore
Pat. Nos. 51383, 66959, 71976; European
Pat. Nos. 0 842 463 (96927260.8), 1 010 057
(98903671.0), 1018 069 (98950708.2);
Republic of Korea Pat. Nos. KR201211B1,
KR226206B1, 402252; People's Republic of
China Pat. No. ZL96196739.0; Mexico Pat.
Nos. 208141, 216023, 218409; Russian
Federation Pat. Nos. 2206118, 2214620,
2221268; and additional patents are pending
worldwide.
T9® Chinese Phrasal Text Input is covered
by patents pending worldwide.
• Other company and product names
mentioned in this manual are trademarks or
registered trademarks of their respective
holders.
• The abbreviations of operating systems
below are used in this manual:
- Windows Vista stands for Windows Vista™
(Home Basic, Home Premium, Business,
Enterprise and Ultimate).
- Windows XP indicates the Microsoft®
Windows® XP Professional operating
system or Microsoft® Windows® XP Home
Edition operating system.
- Windows 2000 indicates the Microsoft®
Windows® 2000 Professional operating
system.
❖Others
• This product contains a module developed
by the Independent JPEG Group.
• This product is equipped with the
technologies of GestureTek, Inc.
3+4DQQM2CIG9GFPGUFC[#RTKN2/
21
Copyright© 2008, GestureTek, Inc. All Rights
Reserved.
• This product is licensed based on MPEG-4
Visual Patent Portfolio License. The use of
MPEG-4 Video Codec function is allowed for
personal and nonprofit use only in the cases
below:
- Recording movies and i-motion that
conform to MPEG-4 Visual Standard
(hereinafter referred to as MPEG-4 Video)
- Playing MPEG-4 Videos recorded
personally by consumers not engaged in
profit activities
- Playing MPEG-4 Video supplied from the
provider licensed from MPEG-LA. For
further utilizing such as promotion, in-
house use or profit-making business,
please contact MPEG LA, LLC in the U.S.
• Licensed by QUALCOMM Incorporated
under one or more of the following United
States Patents and/or their counterparts in
other nations:
4,901,307 5,504,773 5,109,390
5,535,239 5,267,262 5,600,754
5,416,797 5,490,165 5,101,501
5,511,073 5,267,261 5,568,483
5,414,796 5,659,569 5,056,109
5,506,865 5,228,054 5,544,196
5,337,338 5,657,420 5,710,784
5,778,338
• Content owners use Windows Media digital
rights management technology (WMDRM) to
protect their intellectual property, including
copyrights. This device uses WMDRM
software to access WMDRM-protected
content. If the WMDRM software fails to
protect the content, content owners may ask
Microsoft to revoke the software's ability to
use WMDRM to play or copy protected
content. Revocation does not affect
unprotected content. When downloading
licenses for protected content, you agree
that Microsoft may include a "Revocation
List" with the licenses. Content owners may
require you to upgrade WMDRM to access
their content. If you decline an upgrade, you
cannot access a content that requires the
upgrade.
End User License Agreement
Please read thoroughly this End User License
Agreement before using the software installed
on your F905i mobile phone product ("Installed
Software") and the software bundled with the
product ("Bundled Software"). By using the
F905i mobile phone product or the media
delivered with the product, you are agreeing to
be bound by the terms of this license.
Article 1. Copyright
The copyright for the Installed Software and
the Bundled Software belongs to FUJITSU
LIMITED ("Fujitsu") and its third party suppliers
and licensors.
Article 2. Grant of License
Subject to this license, Fujitsu grants you non-
exclusive and non-transferable rights, which
only permit you to use the Installed Software
3+4DQQM2CIG9GFPGUFC[#RTKN2/
22
and to install the Bundled Software on
Personal Computer for private use only.
Article 3. Restricted Activities
(1) The Installed Software and the Bundled
Software are protected by patent, copyright,
and other intellectual property rights. You must
not perform any act that infringes any of these
rights.
(2) You must not modify, decompile,
disassemble, or otherwise reverse engineer
the Installed Software and the Bundled
Software.
(3) You must not reproduce all or any part of
the Installed Software.
(4) You are permitted to make a single copy of
the Bundled Software, solely for backup
purpose. If the Bundled Software is copied in
accordance with this clause, the copyright
must not be changed, deleted or hidden.
(5) You are not permitted to sell, distribute,
lend, or transfer to a third party all or any part
of the Installed Software and of the Bundled
Software, including its backup copy.
Article 4. Termination of License
(1) If you violate the terms of this license or
perform unlawful or unreasonable acts, this
license will terminate with immediate effect.
(2) If this license is terminated as a result of
the clause (1) above, you must immediately
stop using the Installed Software and the
Bundled Software, return the F905i mobile
phone product, the Bundled Software and its
backup copy to Fujitsu, and delete the
Bundled Software from the Personal Computer
in a non-recoverable manner.
Article 5. Others
The specifications of the Installed Software
and of the Bundled Software are subject to
change without prior notice.
F905i package
<F905i package contents> :
• F905i mobile phone terminal (including its
battery cover F-BCA1)
• Battery pack F-BPA1
• AC adapter F-ACA1
• Remote controller with stereo earphone
interface and microphone F-RCA1
• PC data cable F-UCA1
• CD-ROM for F905i (Containing the Quick and
Detailed User Manuals for F905i and the
Datalink software for F905i)
• Quick User Manual for F905i (Chinese
version)
Use only battery pack, AC adapter and
accessories specified and approved by
Fujitsu for this particular model, as listed
above. The use of any other type would
invalidate any warranty and approval, may
damage the equipment, and may be
dangerous.
Limited warranty
A limited warranty is provided for the F905i
3+4DQQM2CIG9GFPGUFC[#RTKN2/
23
mobile phone terminal and the original
accessories delivered with the mobile phone
(hereafter referred to as ÅgProductÅh). Make
sure that you received the related warranty
pamphlet from your network operator
FarEasTone and refer to it, in case your
Product needs warranty service. Warranty
service can be obtained only in Taiwan (please
contact FarEasTone Customer Service).
Please note that the data, applications or
settings you created, imported or downloaded
may be changed or lost when your Product is
repaired or replaced. We assume no liability or
responsibility whatsoever for any change or
loss of information. You should therefore
always maintain a separate record of all the
information registered in your mobile phone
(such as phonebook contents, etc.).
Note that repair or replacement may involve
the use of functionally equivalent
reconditioned or new parts, accessories or
units.
The following is excluded from the limited
warranty:
1 Failure or deterioration due to normal
wear and tear, including all externally
exposed parts and surfaces that are
scratched or damaged due to customer
use.
2 Defect or damage resulting from
improper operation, misuse, accident,
neglect, rough handling or any use in
contradiction with the instructions of the
user manual.
3 Damage or malfunction due to an external
cause of the Product, such as shock,
lightning, fire, unsuitable electric current,
contact with liquid, water, rain, chemical
product or any harmful agent, exposure
to moisture, condensation, perspiration or
dampness, contact with sand, dirt or
food, contact with magnetic cards or
devices, etc.
4 Defect or damage resulting from poor
environmental conditions, such as
extreme temperature or humidity,
variations in electric voltage, forces of
nature, etc. or resulting from any other
acts beyond Fujitsu’s reasonable control.
5 Malfunction or defect resulting from the
use of a SIM/USIM card provided by
someone other than FarEasTone.
6 Damage or malfunction due to a defective
function of the cellular network, or due to
any communication service or signal you
may subscribe to or use with the Product.
Defect or need of software upgrade due
to change of parameters of the cellular
network after the Product has been
purchased, are also not covered by the
warranty.
7 Failure or damage resulting from the use
of or connection to any equipment,
accessory, software or other peripheral
device which is not Fujitsu-branded
original Product, officially specified and
approved for use with F905i mobile
phone terminal.
3+4DQQM2CIG9GFPGUFC[#RTKN2/
24
8 Failure or damage resulting from
installation, adjustment, repair,
modification or opening of the Product
performed by a non-authorized person.
9 Product with any inscription sticker or
seal that has been removed, altered,
obliterated or made illegible, or that
shows evidence of tampering.
10 Defect caused by the fact that the battery
was short-circuited or was used in
equipment other than the one for which it
has been specified.
11 Malfunction or damage caused by any
downloaded contents, data or
application, and loss or deterioration of
the said downloaded contents, data or
application.
12 Software embodied in physical media,
such as CD-ROM, is provided “as is”, and
no warranty is made that the software will
meet your requirements or will work in
combination with any equipment or
application provided by third parties and
that the operation of the software will be
uninterrupted or error free.
13 The display may have some dots always
lit or unlit, and minor variations in display
brightness and color may occur between
mobile phones: this shows characteristics
of liquid crystal displays and not defects
in the mobile phone terminal. Repair of
the display or external connector if
broken after purchase is also not covered
by the warranty.
14 IN NO EVENT SHALL WE BE LIABLE,
WHETHER IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE) FOR
DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT,
OR FOR ANY INDIRECT, INCIDENTAL,
SPECIAL OR CONSEQUENTIAL
DAMAGES OF ANY KIND, OR LOSS OF
REVENUE OR PROFITS, LOSS OF
BUSINESS, LOSS OF INFORMATION OR
DATA, SOFTWARE OR APPLICATIONS
OR OTHER FINANCIAL LOSS ARISING
OUT OF OR IN CONNECTION WITH THE
ABILITY OR INABILITY TO USE THE
PRODUCT TO THE FULL EXTENT THESE
DAMAGES MAY BE DISCLAIMED BY
LAW.
Some states and jurisdictions do not allow the
exclusion or limitation of incidental or
consequential damages to its fullest extent
under certain circumstances, so the preceding
limitations or exclusions may not apply to you.
SAR and Certification
Information
For further information about Specific
Absorption Rate (SAR), please see the website
below:
World Health Organization (WHO):
http://www.who.int/peh-emf/
3+4DQQM2CIG9GFPGUFC[#RTKN2/
25
❖National Communications
Commission (NCC) Notice
Without permission granted by the NCC, any
company, enterprise, or user is not allowed to
change frequency, enhance transmitting
power or alter original characteristic as well as
performance to an approved low power radio-
frequency device.
The low power radio-frequency devices shall
not influence aircraft security and interfere
legal communications. If found, the user shall
cease operating immediately until no
interference is achieved. The said legal
communications means radio communications
are operated in compliance with the
Telecommunications Act.
The maximum SAR allowed in Taiwan is 2.0 W/
kg; the actual SAR level from the submitted
test sample is X.XXX W/kg.
Please limit exposure to reduce the affect of
electromagnetic energy.
❖Declaration of Conformity
The product "F905i" is declared to conform to
the essential requirements of European Union
Directive 1999/5/EC Radio and
Telecommunications Terminal Equipment
Directive 3.1(a), 3.1(b) and 3.2.
The Declaration of Conformity can be found on
http://www.fmworld.net/product/phone/doc/.
This mobile phone complies with the EU
requirements for exposure to radio waves.
Your mobile phone is a radio transceiver,
designed and manufactured not to exceed the
SAR* limits** for exposure to radio-
frequency(RF) energy, which SAR* value,
when tested for compliance against the
standard was X.XXX W/kg. While there may be
differences between the SAR* levels of various
phones and at various positions, they all
meet*** the EU requirements for RF exposure.
*The exposure standard for mobile phones
employs a unit of measurement known as the
Specific Absorption Rate, or SAR.
** The SAR limit for mobile phones used by the
public is 2.0 watts/kilogram (W/kg) averaged
over ten grams of tissue, recommended by
The Council of the European Union. The limit
incorporates a substantial margin of safety to
give additional protection for the public and to
account for any variations in measurements.
*** Tests for SAR have been conducted using
standard operation positions with the phone
transmitting at its highest certified power level
in all tested frequency bands. Although the
SAR is determined at the highest certified
power level, the actual SAR level of the phone
while operating can be well below the
maximum value. This is because the phone is
designed to operate at multiple power levels
so as to use only the power required to reach
the network. In general, the closer you are to a
base station antenna, the lower the power
output.
❖Federal Communications
Commission (FCC) Notice
• This device complies with part 15 of the FCC
rules.
Operation is subject to the following two
conditions:
3+4DQQM2CIG9GFPGUFC[#RTKN2/
26
athis device may not cause harmful
interference, and
bthis device must accept any interference
received, including interference that may
cause undesired operation.
• Changes or modifications made in or to the
radio phone, not expressly approved by the
manufacturer, will void the user’s authority to
operate the equipment.
❖Industry Canada (IC) Notice
• Operation is subject to the following two
conditions :
athis device may not cause interference, and
bthis device must accept any interference,
including interference that may cause
undesired operation of the device.
❖FCC and IC RF Exposure
Information
This model phone meets the U.S.
Government’s and Canadian Government’s
requirements for exposure to radio waves. This
model phone contains a radio transmitter and
receiver.
This model phone is designed and
manufactured not to exceed the emission
limits for exposure to radio frequency (RF)
energy as set by the FCC of the U.S.
Government and IC of the Canadian
Government. These limits are part of
comprehensive guidelines and establish
permitted levels of RF energy for the general
population. The guidelines are based on
standards that were developed by
independent scientific organizations through
periodic and thorough evaluation of scientific
studies.
The exposure standard for wireless mobile
phones employs a unit of measurement known
as the Specific Absorption Rate (SAR). The
SAR limit set by the FCC and IC is 1.6 W/kg.
Tests for SAR are conducted using standard
operating positions as accepted by the FCC
and IC with the phone transmitting at its
highest certified power level in all tested
frequency bands. Although the SAR is
determined at the highest certified power level,
the actual SAR level of the phone while
operating can be well below the maximum
value. This is because the phone is designed
to operate at multiple power levels so as to use
only the power required to reach the network.
In general, the closer you are to a wireless
base station antenna, the lower the power
output level of the phone.
Before a phone model is available for sale to
the public, it must be tested and certified to
prove to the FCC and IC that it does not
exceed the limit established by the U.S. and
Canadian government-adopted requirement
for safe exposure. The tests are performed on
position and locations (for example, at the ear
and worn on the body) as required by FCC
and IC for each model. The highest SAR value
for this model phone as reported to the FCC
and IC, when tested for use at the ear, is X.XXX
W/kg, and when worn on the body, is X.XXX W/
kg. (Body-worn measurements differ among
phone models, depending upon available
accessories and FCC and IC requirements).
While there may be differences between the
SAR levels of various phones and at various
positions, they all meet the U.S. and Canadian
3+4DQQM2CIG9GFPGUFC[#RTKN2/
X.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X.
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XXX
XXX
X
XX
XX
XXX
XXX
X
X
XXX
XXX
XX
X
X
X
X
X
X
X
XX
X
X
X
X
XXX
X
XXX
XXX
XXX
X
XXX
X
X
XXX
XXX
X
X
X
X
XXX
XX
XXX
XXX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XXX
X
X
XX
XX
XXX
XXX
XX
XXX
X
XXX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XXX
XX
XXX
XXX
X
X
XX
X
X
XXX
X
X
XXX
X
X
XX
X
X
X
X
X
X
X
X
XX
X
X
XXX
X
X
X
X
X
X
X
XXX
X
X
XXX
X
X
X
XX
XX
X
X
XXX
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XXX
X
X
X
X
X
XXX
XXX
X
X
X
X
XXX
XXX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XXX
XXX
X
X
X
X
X
X
X
XXX
X
X
X
XX
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
XX
X
X
X
27
government requirements.
The FCC and IC has granted an Equipment
Authorization for this model phone with all
reported SAR levels evaluated as in
compliance with the FCC and IC RF exposure
guidelines. SAR information on this model
phone is on file with the FCC and can be found
under the Equipment Authorization Search
section at http://www.fcc.gov/oet/ (please
search on FCC ID XXXXXXXXXX).
For body worn operation, this phone has been
tested and meets the FCC and IC RF exposure
guidelines when used with an accessory
designated for this product or when used with
an accessory that contains no metal and which
positions the handset at a minimum distance of
1.5 cm from the body.
* In the United States and Canada, the SAR
limit for wireless mobile phones used by the
general public is 1.6 Watts/kg (W/kg),
averaged over one gram of tissue. SAR values
may vary depending upon national reporting
requirements and the network band.
❖Important Safety Information
AIRCRAFT
Switch OFF your wireless device when
boarding an aircraft or whenever you are
instructed to do so by airline staff. If your
device offers flight mode or similar feature
consult airline staff as to whether it can be
used on board.
DRIVING
Do not use the phone while driving. Before
making or answering a call, pull off the road
and park at a safe place.
HOSPITALS
Mobile phones should be switched OFF
wherever you are requested to do so in
hospitals, clinics or health care facilities. These
requests are designed to prevent possible
interference with sensitive medical equipment.
PETROL STATIONS
Obey all posted signs with respect to the use
of wireless devices or other radio equipment in
locations with flammable material and
chemicals. Switch off your wireless device
whenever you are instructed to do so by
authorized staff.
INTERFERENCE
Care must be taken when using the phone in
close proximity to personal medical devices,
such as pacemakers and hearing aids.
Pacemakers
Pacemaker manufacturers recommend that a
minimum separation of 15 cm be maintained
between a mobile phone and a pace maker to
avoid potential interference with the
pacemaker. To achieve this use the phone on
the opposite ear to your pacemaker and does
not carry it in a breast pocket.
Hearing Aids
Some digital wireless phones may interfere
with some hearing aids. In the event of such
interference, you may want to consult your
hearing aid manufacturer to discuss
alternatives.
For other Medical Devices
Please consult your physician and the device
manufacturer to determine if operation of your
3+4DQQM2CIG9GFPGUFC[#RTKN2/
28
phone may interfere with the operation of your
medical device.
Export Administration
Regulations of Japan and the
U.S.
This product and its accessories are under
coverage of the Export Administration
Regulations ("Foreign Exchange and
Foreign Trade Control Laws" and the
related laws and regulations) of Japan and
the Export Administration Regulations of
the U.S. When exporting or reexporting this
product and its accessories, take necessary
procedures on your responsibility and
expense. For details, contact the Ministry of
Economy, Trade and Industry of Japan or
the U.S. Department of Commerce.
3+4DQQM2CIG9GFPGUFC[#RTKN2/
29
F905i mobile phone terminal
Maker: FUJITSU LIMITED
Made in Japan
Importer: FarEasTone Telecommunications Co., Ltd.
Address: 5F, 468, Ruei Guang Rd., Nei Hu, Taipei Taiwan
Tel: +886 2 8793 5000
www.fetnet.net
FarEasTone mobile customers, please dial 888 for customer services
This printed matter is recyclable. Please recycle this manual when you no longer need it for
reference purposes.
3+4DQQM2CIG9GFPGUFC[#RTKN2/
30
3+4DQQM2CIG9GFPGUFC[#RTKN2/