TransCore 76007 FHSS TRANSCEIVER MODULE User Manual 4

TransCore FHSS TRANSCEIVER MODULE 4

User Manual 4

795.0 UPC TypesNOTE: To minimize the risk of invalid data transmission, we rec-ommend selecting whether to read or ignore supplemental characters.5.1.7 Decode UPC/EAN Supplementals : Parameter # 0x10Supplementals are appended characters (2 or 5) according to specic code format conventions (e.g., UPC A+2, UPC E+2). To enable or disable EAN-13, scan the appropriate bar code below.:• If Decode UPC/EAN with Supplemental characters is selected, thescanner does not decode UPC/EAN symbols without supplemental characters.• IfIgnoreUPC/EANwithSupplementalcharactersisselected,andtheSE-955 is presented with a UPC/EAN symbol with a supplemental, the scanner decodes the UPC/EAN and ignores the supplemental characters.• IfAutodiscriminateUPC/EAN Supplementals is selected, scanDe-code UPC/EAN Supplemental Redundancy on page 8-25, then select a value from the numeric bar codes beginning on page 8-71. A value of 5 or more is recommended.• Select Enable378/379 Supplemental Mode to enablethe SE-955 toidentify supplementals for EAN-13 bar codes starting with a ‘378’ or ‘379’ prex only. All other UPC/EAN bar codes are decoded immedi-ately and the supplemental characters ignored.Decode UPC/EAN With Supplementals(0x01)Autodiscriminate UPC/EAN Supplementals(0x02)Enable 378/379 Supplemental Mode(0x04)*Ignore UPC/EAN With Supplementals(0x00)• SelectEnable978SupplementalModetoenabletheSE-955toiden-tify supplementals for EAN-13 bar codes starting with a ‘978’ prex only. All other UPC/EAN bar codes are decoded immediately and the supplemental characters ignored.• SelectEnableSmartSupplementalModetoenabletheSE-955toiden-tify supplementals for EAN-13 bar codes starting with a ‘378’, ‘379’, or ‘978’ prex only. All other UPC/EAN bar codes are decoded immedi-ately and the supplemental characters ignored.Enable 978 Supplemental Mode(0x05)Enable Smart Supplemental Mode(0x03)Decode UPC/EAN Supplemental Redundancy(Default: 7)5.1.8 Decode UPC/EAN Supplemental Redun-dancy : Parameter # 0x50With Autodiscriminate UPC/EAN Supplementals selected, this option adjusts the number of times a symbol without supplementals will be de-coded before transmission. e range is from 2 to 30 times. Five or above is recommended when decoding a mix of UPC/EAN symbols with and without supplementals, and the autodiscriminate option is selected.Scan the bar code below to select a decode redundancy value. Next scan two numeric bar codes beginning on page 8-71. Single digit numbers must have a leading zero. To change the selection or cancel an incorrect entry, scan the Cancel bar code on page 8-72.
805.0 UPC Types5.1.9 Transmit UPC-A Check Digit : Parameter # 0x28Scan the appropriate bar code below to transmit the symbol with or without the UPC-A check digit.5.1.10 Transmit UPC-E Check Digit : Parameter # 0x29Scan the appropriate bar code below to transmit the symbol with or without the UPC-E check digit.*Transmit UPC-A Check Digit(0x01)*Transmit UPC-E Check Digit(0x01)Do Not Transmit UPC-A Check Digit(0x00)Do Not Transmit UPC-E Check Digit(0x00)5.1.11 Transmit UPC-E1 Check Digit : Parameter # 0x2AScan the appropriate bar code below to transmit the symbol with or without the UPC-E1 check digit.5.1.12 UPC-A Preamble : Parameter # 0x22Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-A symbol. Select one of the following op-tions for transmitting UPC-A preamble to the host device: transmit sys-tem character only, transmit system character and country code (“0” for USA), or transmit no preamble.*Transmit UPC-A Check Digit(0x01)No Preamble(<DATA>)(0x00)Do Not Transmit UPC-A Check Digit(0x00)*System Character(<SYSTEM CHARACTER> <DATA>)(0x01)System Character & Country Code(< COUNTRY CODE> <SYSTEM CHARACTER> <DATA>)(0x02)5.1.13 UPC-E Preamble : Parameter # 0x23Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-E symbol. Select one of the following op-tions for transmitting UPC-E preamble to the host device: transmit sys-tem character only, transmit system character and country code (“0” for USA), or transmit no preamble.No Preamble(<DATA>)(0x00)*System Character(<SYSTEM CHARACTER> <DATA>)(0x01)System Character & Country Code(< COUNTRY CODE> <SYSTEM CHARACTER> <DATA>)(0x02)
815.0 UPC Types5.1.14 UPC-E1 Preamble : Parameter # 0x24Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-E1 symbol. Select one of the following options for transmitting UPC-E1 preamble to the host device: transmit system character only, transmit system character and country code (“0” for USA), or transmit no preamble.No Preamble(<DATA>)(0x00)*System Character(<SYSTEM CHARACTER> <DATA>)(0x01)System Character & Country Code(< COUNTRY CODE> <SYSTEM CHARACTER> <DATA>)(0x02)5.1.15 Convert UPC-E to UPC-A : Parameter # 0x25Enable this parameter to convert UPC-E (zero suppressed) decoded data to UPC-A format before transmission. Aer conversion, data fol-lows UPC-A format and is aected by UPC-A programming selections (e.g., Preamble, Check Digit).Scan DO NOT CONVERT UPC-E TO UPC-A to transmit UPC-E (zero suppressed) decoded data.5.1.16 Convert UPC-E1 to UPC-A : Parameter # 0x26Enable this parameter to convert UPC-E1 (zero suppressed) decoded data to UPC-A format before transmission. Aer conversion, data fol-lows UPC-A format and is aected by UPC-A programming selections (e.g., Preamble, Check Digit).Scan DO NOT CONVERT UPC-E TO UPC-A to transmit UPC-E1 (zero suppressed) decoded data.Convert UPC-E to UPC-A (Enable)(0x01)Convert UPC-E1 to UPC-A (Enable)(0x01)*Do Not Convert UPC-E to UPC-A (Disable)(0x00)*Do Not Convert UPC-E1 to UPC-A (Disable)(0x00)5.1.17 EAN Zero Extend : Parameter # 0x27When enabled, this parameter adds ve leading zeros to decoded EAN-8 symbols to make them compatible in format to EAN-13 symbols.Disable this parameter to transmit EAN-8 symbols as is.Enable EAN Zero Extend(0x01)*Disable EAN Zero Extend(0x00)5.1.18 Convert EAN-8 to EAN-13 Type : Parameter # 0xE0When EAN Zero Extend is enabled, you can label the extended symbol as either an EAN-13 bar code, or an EAN-8 bar code. is aects Transmit Code ID Character and DECODE_DATA message.When EAN Zero Extend is disabled, this parameter has no eect on bar code data.*Type Is EAN-13(0x00)Type Is EAN-8(0x01)
825.0 UPC Types5.1.19 UPC/EAN Security Level : Parameter # 0x4De SE-955 oers four levels of decode security for UPC/EAN bar codes. Increasing levels of security are provided for decreasing levels of bar code quality. Select higher levels of security for decreasing levels of bar code quality. Increasing security decreases the scanner’s aggressiveness, so choose only that level of security necessary for the application.UPC/EAN Security Level 0: is default setting allows the scanner to operate in its most aggressive state, while providing sucient security in decoding most “in-spec” UPC/EAN bar codes.*UPC/EAN Security Level 0(0x00)UPC/EAN Security Level 1(0x01)UPC/EAN Security Level 2(0x02)UPC/EAN Security Level 3(0x03)UPC/EAN Security Level 1: As bar code quality levels diminish, certain characters become prone to mis-decodes before others (i.e., 1, 2, 7, 8). If mis-decodes of poorly printed bar codes occur, and the mis-decodes are limited to these characters, select this security level.UPC/EAN Security Level 2: If mis-decodes of poorly printed bar codes occur, and the mis-decodes are not limited to characters 1, 2, 7, and 8, select this security level.UPC/EAN Security Level 3: If misdecodes still occur aer selecting Security Level 2, select this security level. Be advised, selecting this op-tion is an extreme measure against mis-decoding severely out of spec bar codes. Selection of this level of security signicantly impairs the de-coding ability of the scanner. If this level of security is necessary, try to improve the quality of the bar codes.5.1.20 UCC Coupon Extended Code : Parameter # 0x55e UCC Coupon Extended Code is an additional bar code adjacent to a UCC Coupon Code. To enable or disable UCC Coupon Extended Code, scan the appropriate bar code below.Enable UCC Coupon Extended Code(0x01)*Disable UCC Coupon Extended Code(0x00)5.2 Code 1285.2.1 Enable/Disable Code 128 : Parameter # 0x08To enable or disable Code 128, scan the appropriate bar code below.5.2.2 Enable/Disable UCC/EAN-128 : Parameter # 0x0ETo enable or disable UCC/EAN-128, scan the appropriate bar code be-low. (See Chapter B, Miscellaneous Code Information for details on UCC/EAN-128.)*Enable Code 128(0x01)*Enable UCC/EAN-128(0x01)Disable Code 128(0x00)Disable UCC/EAN-128(0x00)
835.0 UPC Types5.2.3 Enable/Disable ISBT 128 : Parameter # 0x54To enable or disable ISBT 128, scan the appropriate bar code below.5.2.4 Lengths for Code 128No length setting is required for Code 128.*Enable ISBT 128(0x01)Disable ISBT 128(0x00)5.3 Code 395.3.1 Enable/Disable Code 39 : Parameter # 0x00To enable or disable Code 39, scan the appropriate bar code below.5.3.2 Enable/Disable Trioptic Code 39 : Parameter # 0x0DTrioptic Code 39 is a variant of Code 39 used in marking computer tape cartridges. Trioptic Code 39 symbols always contain six characters.To enable or disable Trioptic Code 39, scan the appropriate bar code below.*Enable Code 39(0x01)Enable Trioptic Code 39(0x01)Disable Code 39(0x00)*Disable Trioptic Code 39(0x00)NOTE: Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously. If an error beep sounds when enabling Tri-optic Code 39, disable Code 39 Full ASCII and try again.5.3.3 Convert Code 39 to Code 32 (Italian Pharma Code) : Parameter # 0x56Code 32 is a variant of Code 39 used by the Italian pharmaceutical in-dustry. Scan the appropriate bar code below to enable or disable con-verting Code 39 to Code 32.Enable Convert Code 39 to Code 32(0x01)NOTE: Code 39 must be enabled in order for this parameter to func-tion.5.3.4 Code 32 Prex : Parameter # 0xE7Enable this parameter to add the prex character “A” to all Code 32 bar codes. Convert Code 39 to Code 32 (Italian Pharma Code) must be enabled for this parameter to function.Enable Code 32 Prex(0x01)*Disable Convert Code 39 to Code 32(0x00)*Disable Code 32 Prex(0x00)5.3.5 Set Lengths for Code 39 : Parameter # L1 = 0x12, L2 = 0x13e length of a code refers to the number of characters (i.e., human read-able characters), including check digit(s) the code contains. Lengths for Code 39 may be set for any length, one or two discrete lengths, or lengths within a specic range. If Code 39 Full ASCII is enabled, Length With-in a Range or Any Length are the preferred options.NOTE: When setting lengths, single digit numbers must always be preceded by a leading zero.
845.0 UPC TypesCode 39 - Two Discrete LengthsCode 39 - Length Within Range• Two Discrete Lengths - is option limits decodes to only those Code 39 symbols containing either of two selected lengths. Lengths are selected from the numeric bar codes in Section 5.5 on page 95. For example, to decode only those Code 39 symbols containing either 2 or 14 characters, scan Code 39 - Two Discrete Lengths, then scan 0, 2, 1 and then 4. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.• Length Within Range - is option limits decodes to only those Code 39 symbols within a specied range. For example, to decode Code 39 symbols containing between 4 and 12 characters, rst scan Code 39 - Length Within Range. en scan 0, 4, 1 and 2. Numeric bar codes are in Section 5.5 on page 95. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.Code 39 - Any Length• Any Length - Scan this option to decode Code 39 symbols contain-ing any number of characters.5.3.6 Code 39 Check Digit Verication : Parameter # 0x30When this feature is enabled, the scanner checks the integrity of all Code 39 symbols to verify that the data complies with specied check digit algorithm. Only those Code 39 symbols which include a modulo 43 check digit are decoded. Only enable this feature if your Code 39 symbols contain a module 43 check digit.Verify Code 39 Check Digit(0x01)*Do Not Verify Code 39 Check Digit(0x00)5.3.7 Transmit Code 39 Check Digit : Parameter # 0x2BScan this symbol to transmit the check digit with the data.Scan this symbol to transmit data without the check digit.Verify Code 39 Check Digit(0x01)*Do Not Verify Code 39 Check Digit(0x00)5.3.8 Enable/Disable Code 39 Full ASCII : Parameter # 0x11Code 39 Full ASCII is a variant of Code 39 which pairs characters to encode the full ASCII character set. To enable or disable Code 39 Full ASCII, scan the appropriate bar code below.Refer to Table B-3 on page B-5 for the mapping of Code 39 characters to ASCII values.Verify Code 39 Check Digit(0x01)*Do Not Verify Code 39 Check Digit(0x00)NOTE: Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously. If you get an error beep when enabling Code 39 Full ASCII, disable Trioptic Code 39 and try again.Code 39 - One Discrete Length• One Discrete Length - is option limits decodes to only those Code 39 symbols containing a selected length. Lengths are selected from the numeric bar codes in Section 5.5 on page 95. For exam-ple, to decode only Code 39 symbols with 14 characters, scan Code 39 - One Discrete Length, then scan 1 followed by 4. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.
855.0 UPC Types5.4 Code 935.4.1 Enable/Disable Code 93 : Parameter # 0x00To enable or disable Code 93, scan the appropriate bar code below.Enable Code 93(0x01)*Disable Code 93(0x00)5.4.2 Set Lengths for Code 93 : Parameter # L1 = 0x1A, L2 = 0x1Be length of a code refers to the number of characters (i.e., human read-able characters), including check digit(s) the code contains. Lengths for Code 93 may be set for any length, one or two discrete lengths, or lengths within a specic range.• One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select Code 93 - One Discrete Length, then scan 1, 4 to limit the decoding to only Code 93 symbols containing 14 characters. Numeric bar codes are in Section 5.5 on page 95. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.Code 93 - One Discrete LengthCode 93 - Two Discrete Lengths• Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example, select Code 39 - Two Discrete Lengths, then scan 0, 2, 1, 4 to limit the decoding to only Code 93 symbols containing 2 or 14 characters. Numeric bar codes are in Section 5.5 on page 95. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.Code 93 - Length Within Range• Length Within Range - is option sets the unit to decode a code type within a specied range. For example, to decode Code 93 symbols containing between 4 and 12 characters, rst scan Code 39 - Length Within Range. en scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes are in Sec-tion 5.5 on page 95. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.Code 93 - Any Length• Any Length - Scan this option to decode Code 93 symbols contain-ing any number of characters.5.5 Code 115.5.1 Enable/Disable Code 11 : Parameter # 0x0ATo enable or disable Code 11, scan the appropriate bar code below.Enable Code 11(0x01)*Disable Code 11(0x00)5.5.2 Set Lengths for Code 11 : Parameter # L1 = 0x1C, L2 = 0x1De length of a code refers to the number of characters (i.e., human read-able characters), including check digit(s) the code contains. Set lengths for Code 11 to any length, one or two discrete lengths, or lengths within a specic range.• OneDiscreteLength - Select this option to decode only Code 11 symbols containing a selected length. Select the length using the nu-meric bar codes in Numeric Bar Codes in Section 5.5 on page 95. For example, to decode only Code 11 symbols with 14 characters, scan Code 11 - One Discrete Length, then scan 1 followed by 4. To correct an error or to change the selection, scan Cancel in Section 5.5.1 on page 95.Code 11 - One Discrete LengthCode 11 - Two Discrete Lengths• Two Discrete Lengths - Select this option to decode only Code 11 symbols containing either of two selected lengths. Select lengths us-ing the numeric bar codes in Numeric Bar Codes on page 8-76. For ex-ample, to decode only those Code 11 symbols containing either 2 or 14 characters, select Code 11 - Two Discrete Lengths, then scan 0, 2, 1, and then 4. To correct an error or to change the selection, scan Cancel in Section 5.5.1 on page 95.
865.0 UPC TypesCode 11 - Length Within RangeLength Within Range - Select this option to decode a Code 11 sym-bol with a specic length range. Select lengths using numeric bar codes in Numeric Bar Codes on page 8-76. For example, to decode Code 11 symbols containing between 4 and 12 characters, rst scan Code 11 - Length Within Range. en scan 0, 4, 1, and 2 (single digit num-bers must always be preceded by a leading zero). To correct an error or change the selection, scan Cancel in Section 5.5.1 on page 95.Code 11 - Any LengthAny Length - Scan this option to decode Code 11 symbols containing any number of characters within the scanner capability.5.5.3 Code 11 Check Digit Verication : Parameter # 0x34is feature allows the scanner to check the integrity of all Code 11 symbols to verify that the data complies with the specied check digit algorithm. is selects the check digit mechanism for the decoded Code 11 bar code. e options are to check for one check digit, check for two check digits, or disable the feature.To enable this feature, scan the bar code below corresponding to the number of check digits encoded in your Code 11 symbols.*Disable(0x00)One Check Digit(0x01)Two Check Digits(0x02)5.5.4 Transmit Code 11 Check Digits : Parameter # 0x2Fis feature selects whether or not to transmit the Code 11 check digit(s).Transmit Code 11 Check Digit(s) (Enable)(0x01)*Do Not Transmit Code 11 Check Digit(s) (Disable)(0x00)NOTE: Code 11 Check Digit Verication must be enabled for this pa-rameter to function.*Enable Interleaved 2 of 5(0x01)Disable Interleaved 2 of 5(0x00)5.6 Interleaved 2 of 55.6.1 Enable/Disable Interleaved 2 of 5 : Parameter # 0x06To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.5.6.2 Set Lengths for Interleaved 2 of 5 : Parameter # L1 = 0x16, L2 = 0x17e length of a code refers to the number of characters (i.e., human read-able characters), including check digit(s) the code contains. Lengths for I 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specic range.NOTE: When setting lengths, single digit numbers must always be preceded by a leading zero.
875.0 UPC TypesI 2 of 5 - One Discrete LengthI 2 of 5 - Two Discrete Lengths• One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select I 2 of 5 - One Dis-crete Length, then scan 1, 4, to decode only I 2 of 5 symbols con-taining 14 characters. Numeric bar codes are in Section 5.5 on page 95. To change the selection or cancel an incorrect entry,scan Cancel in Section 5.5.1 on page 95.• Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example, select I 2 of 5 - Two Discrete Lengths, then scan 0, 6, 1, 4 to decode only I 2 of 5 symbols containing 6 or 14 characters. Numeric bar codes begin on page 8-71. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.I 2 of 5 - Length Within Range• Length Within Range - Select this option to decode only codes within a specied range. For example, to decode I 2 of 5 symbols containing between 4 and 12 characters, rst scan I 2 of 5 - Length Within Range. en scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes begin are in Section 5.5 on page 95. To change the selection or cancel an incor-rect entry, scan Cancel in Section 5.5.1 on page 95.I 2 of 5 - Any Length• Any Length - Scan this option to decode Code 39 symbols contain-ing any number of characters.NOTE: Selecting this option may lead to misdecodes for I 2 of 5 codes.5.6.3 Interleaved 2 of 5 Check Digit Verica-tion : Parameter # 0x31When enabled, this parameter checks the integrity of an I 2 of 5 symbol to ensure it complies with a specied algorithm, either USS (Uniform Symbology Specication), or OPCC (Optical Product Code Council).*Disable(0x00)USS Check Digit(0x01)OPCC Check Digit(0x02)5.6.4 Transmit Interleaved 2 of 5 Check Digit: Parameter # 0x2CScan this symbol to transmit the check digit with the data.5.6.5 Convert Interleaved 2 of 5 to EAN-13 : Parameter # 0x52is parameter converts a 14 character I 2 of 5 code into EAN-13, and transmits to the host as EAN-13. To accomplish this, I 2 of 5 must be enabled, one length must be set to 14, and the code must have a leading zero and a valid EAN-13 check digit.Scan this symbol to transmit data without the check digit.*Do Not Transmit I 2 of 5 Check Digit (Disable)(0x00)*Do Not Convert I 2 of 5 to EAN-13 (Disable)(0x00)Transmit I 2 of 5 Check Digit (Enable)(0x01)Convert I 2 of 5 to EAN-13 (Enable)(0x01)
885.0 UPC TypesEnable Discrete 2 of 5(0x01)*Disable Discrete 2 of 5(0x00)5.7 Discrete 2 of 55.7.1 Enable/Disable Discrete 2 of 5 : Parameter # 0x05To enable or disable Discrete 2 of 5, scan the appropriate bar code below.5.7.2 Set Lengths for Discrete 2 of 5 : Parameter # L1 = 0x14, L2 = 0x15e length of a code refers to the number of characters (i.e., human read-able characters), including check digit(s) the code contains. Lengths for D 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specic range.• One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select D 2 of 5 - One Dis-crete Length, then scan 1, 4, to decode only D 2 of 5 symbols con-taining 14 characters. Numeric bar codes are in Section 5.5 on page 95. To change the selection or cancel an incorrect entry,scan Cancel in Section 5.5.1 on page 95.D 2 of 5 - One Discrete LengthD 2 of 5 - Two Discrete Lengths• Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example, select D 2 of 5 - Two Discrete Lengths, then scan 0, 4, 1, 2 (single digit numbers must be preceded by a leading zero). Numeric bar codes begin on page 8-71. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.D 2 of 5 - Length Within Range• Length Within Range - Select this option to decode only codes within a specied range. For example, to decode D 2 of 5 symbols containing between 4 and 12 characters, rst scan D 2 of 5 - Length Within Range. en scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes are in Sec-tion 5.5 on page 95. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.D 2 of 5 - Any Length• Any Length - Scan this option to decode D 2 of 5 symbols containing any number of characters.NOTE: Selecting this option may lead to misdecodes for D 2 of 5 codes.Enable Chinese 2 of 5(0x01)*Disable Chinese 2 of 5(0x00)5.8 Chinese 2 of 55.8.1 Enable/Disable Chinese 2 of 5 : Parameter # 0xF0 0x98To enable or disable Chinese 2 of 5, scan the appropriate bar code below.Enable Codabar(0x01)*Disable Codabar(0x00)5.9 Codabar5.9.1 Enable/Disable Codabar : Parameter # 0x07To enable or disable Codabar, scan the appropriate bar code below.
895.0 UPC Types5.9.2 Set Lengths for Codabar : Parameter # L1 = 0x18, L2 = 0x19e length of a code refers to the number of characters (i.e., human read-able characters), including check digit(s) the code contains. Lengths for Codabar may be set for any length, one or two discrete lengths, or lengths within a specic range. • One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select Codabar - One Dis-crete Length, then scan 1, 4, to decode only Codabar symbols con-taining 14 characters. Numeric bar codes are in Section 5.5 on page 95. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.Codabar - One Discrete LengthCodabar - Two Discrete Lengths• Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example, select Codabar - Two Discrete Lengths, then scan 0, 2, 1, 4 to decode only Codabar symbols containing 6 or 14 characters. Numeric bar codes are in Sec-tion 5.5 on page 95. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.Codabar - Length Within Range• Length Within Range - Select this option to decode only codes with-in a specied range. For example, to decode D 2 of 5 symbols contain-ing between 4 and 12 characters, rst scan D 2 of 5 - Length Within Range. en scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes are in Section 5.5 on page 95. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.Codabar - Any Length• Any Length - Scan this option to decode D 2 of 5 symbols containing any number of characters.NOTE: Selecting this option may lead to misdecodes for D 2 of 5 codes.NOTE: Symbol length does not include start and stop characters.5.9.3 CLSI Editing : Parameter # 0x36When enabled, this parameter strips the start and stop characters and inserts a space aer the rst, h, and tenth characters of a 14-character Codabar symbol.Enable CLSI Editing(0x01)*Disable CLSI Editing(0x00)5.9.4 NOTIS Editing : Parameter # 0x37When enabled, this parameter strips the start and stop characters from decoded Codabar symbol.Enable NOTIS Editing(0x01)*Disable NOTIS Editing(0x00)Enable MSI(0x01)*Disable MSI(0x00)5.10 MSI5.10.1 Enable/Disable MSI : Parameter # 0x0BTo enable or disable MSI, scan the appropriate bar code below.
905.0 UPC Types5.10.2 Set Lengths for MSI : Parameter # L1 = 0x1E, L2 = 0x1Fe length of a code refers to the number of characters (i.e., human read-able characters) the code contains, and includes check digits. Lengths for MSI can be set for any length, one or two discrete lengths, or lengths within a specic range. See Table B-5 on page B-9 for ASCII equivalents. MSI - One Discrete LengthMSI - Two Discrete LengthsMSI - Length Within Range• One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select MSI Plessey - One Discrete Length, then scan 1, 4 to limit the decoding to only MSI Plessey symbols containing 14 characters. Numeric bar codes are in Section 5.5 on page 95. To change the selection or cancel an incor-rect entry, scan Cancel in Section 5.5.1 on page 95.• Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example, select MSI Plessey - Two Discrete Lengths, then scan 0, 6, 1, 4 to decode only MSI Plessey symbols containing 6 or 14 characters. Numeric bar codes are in Section 5.5 on page 95. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.• Length Within Range - Select this option to decode codes within a specied range. For example, to decode MSI symbols containing be-tween 4 and 12 characters, rst scan MSI Plessey - Length Within Range. en scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes are in Section 5.5 on page 95. To change the selection or cancel an incorrect entry, scan Cancel in Section 5.5.1 on page 95.MSI - Any Length• Any Length - Scan this option to decode MSI Plessey symbols con-taining any number of characters.NOTE: Selecting this option may lead to misdecodes for MSI codes.5.10.3 MSI Check Digits : Parameter # 0x32ese check digits at the end of the bar code verify the integrity of the data. At least one check digit is always required. Check digits are not automatically transmitted with the data.If two check digits is selected, also select an MSI Check Digit Algorithm. See page 8-56.Two MSI Check Digit(0x01)*One MSI Check Digit(0x00)5.10.4 Transmit MSI Check Digit : Parameter # 0x2EScan this symbol to transmit the check digit with the data.Scan this symbol to transmit data without the check digit.*Do Not Transmit MSI Check Digit (Disable)(0x00)Transmit MSI Check Digit (Enable)(0x01)5.10.5 MSI Check Digit Algorithm : Parameter # 0x33When the Two MSI check digits option is selected, an additional veri-cation is required to ensure integrity. Select one of the following algo-rithms.*MOD 10/ MOD 10(0x01)MOD 10/ MOD 11(0x00)
915.0 UPC TypesEnable RSS-14(0x01)*Disable RSS-14(0x00)5.11 RSS5.11.1 Enable/Disable RSS-14 : Parameter # 0xF0 0x52To enable or disable RSS-14, scan the appropriate bar code below.5.11.2 Enable/Disable RSS-Limited : Parameter # 0xF0 0x53To enable or disable RSS-Limited, scan the appropriate bar code below.5.11.3 Enable/Disable RSS-Expanded : Parameter # 0xF0 0x54To enable or disable RSS-Expanded, scan the appropriate bar code be-low.*Disable RSS-Limited(0x00)*Disable RSS-Expanded(0x00)Enable RSS-Limited(0x01)Enable RSS-Expanded(0x01)5.12 Data Options5.12.1 Transmit Code ID Character : Parameter # 0x2DA code ID character identies the code type of a scanned bar code. is can be useful when decoding more than one code type. e code ID character is inserted between the prex character (if selected) and the decoded symbol.Select no code ID character, a Symbol Code ID character, or an AIM CodeIDcharacter.eSymbolCodeIDcharactersarelistedbelow;seeB for AIM Code Identiers.• A=UPC-A,UPC-E,UPC-E1,EAN-8,EAN-13• B=Code39,Code32• C=Codabar• D=Code128,ISBT128• E=Code93• F=Interleaved2of5• G=Discrete2of5• J=MSI• K=UCC/EAN-128• L=BooklandEAN• M=TriopticCode39• N=CouponCode• R=RSS-14,RSS-Limited,RSS-ExpandedSymbol Code ID Character(0x02)Aim Code ID Character(0x01)*None(0x00)
925.0 UPC Types5.12.2 Prex/Sufx Values : Parameter # P = 0x69, S1 = 0x68, S2 = 0x6AA prex and/or one or two suxes can be appended to scan data for use in data editing. To set these values, scan a four-digit number (i.e. four bar codes) that corresponds to ASCII values. Numeric Bar Codes are in Section 5.5 on page 95. To change the selection or cancel an incor-rect entry, scan Cancel in Section 5.5.1 on page 95. Scan PrexScan Sufx 1Scan Sufx 2Data Format Cancel5.12.3 Scan Data Transmission Format : Parameter # 0xEBTo change the Scan Data Transmission Format, scan one of the eight bar codes corresponding to the desired format.*Data As Is(0x00)<DATA> <SUFFIX 1>(0x01)<DATA> <SUFFIX 2>(0x02)<PREFIX> <DATA> <SUFFIX 1>(0x05)<DATA> <SUFFIX 1> <SUFFIX 2>(0x03)<PREFIX> <DATA> <SUFFIX 2>(0x06)<PREFIX> <DATA >(0x04)<PREFIX> <DATA> <SUFFIX 1> <SUFFIX 2>(0x07)
935.0 UPC Types5.13 Serial Interface5.13.1 Baud Rate : Parameter # 0x9CBaud rate is the number of bits of data transmitted per second. e scan-ner’s baud rate setting should match the data rate setting of the host device. If not, data may not reach the host device or may reach it in distorted form.Baud Rate 300(0x01)Baud Rate 600(0x02)Baud Rate 1200(0x03)*Baud Rate 9600(0x06)Baud Rate 2400(0x04)Baud Rate 19,200(0x07)Baud Rate 4800(0x05)Baud Rate 38,400(0x08)5.13.2 Parity : Parameter # 0x9EA parity check bit is the most signicant bit of each ASCII coded charac-ter. Select the parity type according to host device requirements.If you select ODD parity, the parity bit has a value 0 or 1, based on data, to ensure than an odd number of 1 bits is contained in the coded char-acter.Odd(0x00)Even(0x01)Mark(0x02)Space(0x03)*None(0x04)If you select EVEN parity, the parity bit has a value 0 or 1, based on data, to ensure than an even number of 1 bits is contained in the coded character.Select MARK parity and the parity bit is always 1.Select SPACE parity and the parity bit is always 0.If no parity is required, select NONE.5.13.3 Software Handshaking : Parameter # 0x9Fis parameter oers control of the data transmission process in addi-tion to that oered by hardware handshaking. Hardware handshaking is always enabled and cannot be disabled by the user.Disable ACK/NAK HandshakingWhen this option is selected, the decoder will neither generate nor ex-pect ACK/NAK handshaking packets.Disable ACK/NAK(0x00)
945.0 UPC TypesEnable ACK/NAK HandshakingWhen this option is selected, aer transmitting data, the scanner ex-pects either an ACK or NAK response from the host. e scanner also ACKs or NAKs messages from the host.e scanner waits up to the programmable Host Serial Response Time-out to receive an ACK or NAK. If the scanner does not get a response in this time, it resends its data up to two times before discarding the data and declaring a transmit error.*Enable ACK/NAK(0x01)5.13.4 Decode Data Packet Format : Parameter # 0xEEis parameter selects whether decoded data is transmitted in raw for-mat (unpacketed), or transmitted with the packet format as dened by the serial protocol. If the raw format is selected, ACK/NAK handshak-ing is disabled for decode data.Send Packeted Decode Data(0x01)*Send Raw Decode Data(0x00)5.13.5 Host Serial Response Time-out : Parameter # 0x9Bis parameter species how long the decoder waits for an ACK or NAK before resending. Also, if the decoder wants to send, and the host has already been granted permission to send, the decoder waits for the des-ignated time-out before declaring an error.e delay period can range from 0.0 to 9.9 seconds in 0.1 second incre-ments. Aer scanning the bar code below, scan two numeric bar codes in Section 5.5 on page 95. Values less than 10 require a leading zero. To change the selection or cancel an incorrect entry, scan the Cancel bar code in Section 5.5.1 on page 95.Host Serial Response Time-out(Default: 2.0 sec.)5.13.6 Stop Bit Select : Parameter # 0x9De stop bit(s) at the end of each transmitted character marks the end of transmission of one character and prepares the receiving device for the next character in the serial data stream. Set the number of stop bits (one or two) to match host device requirements.2 Stop Bits(0x02)*1 Stop Bit(0x01)5.13.7 Intercharacter Delay : Parameter # 0x6Ee intercharacter delay gives the host system time to service its receiver and perform other tasks between characters. Select the intercharacter delay option matching host requirements. e delay period can range from no delay to 99 msec in 1 msec increments. Aer scanning the bar code below, scan two bar codes beginning in Section 5.5 on page 95 to set the desired time-out. To change the selection or cancel an incor-rect entry, scan the Cancel bar code in Section 5.5.1 on page 95.5.13.8 Host Character Time-out : Parameter # 0xEFis parameter determines the maximum time the decoder waits be-tween characters transmitted by the host before discarding the received data and declaring an error. e time-out is set in 0.01 second incre-ments from 0.01 seconds to 0.99 seconds. Aer scanning the bar code below, scan two bar codes beginning in Section 5.5 on page 95 to set the desired time-out. To change the selection or cancel an incorrect en-try, scan the Cancel bar code in Section 5.5 on page 95.Intercharacter Delay(Default: 0 sec.)Host Character Time-out(Default: 200 msec.)
955.0 UPC Types5.14.1 Decode Event : Parameter # 0xF0 0x00When enabled, the decoder generates a message to the host whenever a bar code is successfully decoded. When disabled, no notication is sent.5.14.2 Boot Up Event : Parameter # 0xF0 0x02When enabled, the decoder sends a message to the host whenever power is applied. When disabled, no message is sent.*Disable(0x00)*Disable(0x00)Enable(0x01)Enable(0x01)5.14 Event Reportinge host can request the decoder to furnish certain information (events) relative to the decoder’s behavior. Enable or disable the events listed in Table 8-2 by scanning the appropriate bar codes on the following pages. Parameter number format for these parameters follows those shown in Table 9-9 on page 9-20 for parameters numbered 256 or higher.Event Class Event Code ReportedDecode Event Non parameter decode 0x01Boot Up Event System power-up 0x03Parameter EventParameter entry errorParameter storedDefaults set (and parameter event is enabled by default)Number expected0x070x080x0A 0x0F5.14.3 Parameter Event : Parameter # 0xF0 0x03When enabled, the decoder sends a message to the host when one of the events specied in the table in Section 5.14 above occurs. When disabled, no message is sent.*Disable(0x00)Enable(0x01)5.15 Numeric Bar CodesFor parameters requiring specic numeric values, scan the appropri-ately numbered bar code(s).01234568795.15.1 CancelTo change the selection or cancel an incorrect entry, scan the bar code below.Cancel
966.0 Summit Radio6.1 Summit Client UtilityTo launch, double-tap the scu icon at the top of the screen:6.1.1 Main Windowe Main window provides an overview of the current wireless network connection conguration (Active Prole), a snapshot of connection in-formation as well as access to administrator functions (Admin Login/Logout - administrator use only), and additional information regarding SCU (About SCU).e Main window displays the following properties and options:6.0 Summit RadioElement DescriptionAdminLogin/LogoutAdministrator use only.Enable Radio/DisableRadioWhen the radio is enabled, select this button (which displays Disable Radio) to disable it. When the radio is disabled, select the same button (which now displays Enable Radio) to enable it.Note: When the radio is enabled, it attempts to make and/or maintains a connection to an access point. When a radio is disabled, its power remains on but it does not attempt to make a connection to an access point.Active ProleDisplays the name of the active. Use the drop-down menu to select a dierent prole.Note: If irdPartyCong is selected (and aer the device goes through a power cycle), WZC (Windows Zero Conguration) or another application is used to con-gure the SSID, Auth Type, EAP Type, and Encryp-tion settings. See “irdPartyCong” for more infor-mation.Status Indicates the current status of the Summit radio. Connection status options include:Down e radio is not recognized by Summit soware and thus is not associated nor authenticated.Disabled e radio is disabled. To enable the radio, tap Enable Radio located on the SCU Main window.When the radio is disabled, it does not attempt to make a connection to an access point.Status (cont’d)Not Associatede radio has not established a connection to an access point.Associated e radio has established a connection to an access point but is not EAP authenticated. e radio can not communicate unless it is associated and EAP authenticated.Note: If the Encryption type is set to WEP or Open (None), it can communicate (send data) while in the Associated state.<EAP type> Authenti-catede radio has established a connection to an access point and has completed EAP authenti-cation successfully. In this state, the radio can communicate (send data).Radio Type Indicates the type of radio installed in the device. For example:BG Indicates a Summit 802.11g radio which sup-ports 802.11b and 802.11g.ABG Indicates a Summit 802.11a/g radio which sup-ports 802.11a , 802.11b, and 802.11g.N Indicates Summit 802.11n radio which sup-ports 802.11a, 802.11b, 802.11g, and 802.11n.Reg. Domain Indicates the regulatory domain(s) for which the radio is congured, including FCC, ETSI, TELEC, and KCC.Auto Prole Auto prole enables you to activate or deactivate automatic prole selection. Tap List and use the dialog box to select a created prole.Note: ere is a limit of 19 proles in the Auto Prole list.Note: Auto Prole is only available on Windows CE and Windows Mobile operating systems.Driver Indicates the current version of the device driver.SCU Indicates the SCU version currently running on the device. Displays only if space permits.Import/ExportDisplays only if the radio is programmed to allow import/ex-port functions if you are logged in as an administrator.Tap Import/Export and use the dialog box to do one of the following:• Export global settings, all standard SCU proles, and the spe-cial irdPartyCong prole from the SCU area of a device’s registry to a le that can be transferred to another device.• Importglobalsettings,allstandardSCUproles,andthespe-cial irdPartyCong prole from a le (created using the Export facility) to the SCU area of a device’s registry to enable SCU to use the information.Note: When importing information, select Add to existing to merge new information with current registry informa-tion. Select Replace to overwrite the current registry information with the newly-imported information.About SCU Tap About SCU to view SCU information including driver and the SCU version.
976.0 Summit Radio6.1.2 Prole WindowProle settings are radio and security settings that are stored in the reg-istry as part of a conguration prole. When a prole is selected as the active prole on the Main window, the settings for that prole become active.Notes: When the irdPartyCong prole is selected, a power cycle must be performed. See “irdPartyCong” for more informa-tion. If the Default prole is not modied, it does not specify an SSID, an EAP type, or a data encryption method. As a result, if the Default is the active prole, then the radio associates only to an AP that broadcasts its SSID and requires no EAP type and no encryption.From the Prole window, an administrator can:• Deneupto20proles,inadditiontothespecialirdPartyCongprole.• Changeprolesettings.• DeleteanyproleexceptthespecialirdPartyCongandtheactiveprole.Prole changes are not saved to the prole until you tap Commit.Element DescriptionEdit Prole Use the drop-down menu to select the prole to be viewed or edited. Only an administrator can edit a prole.Actions Actions included New, Rename, Delete, and Scan. New, Rename, and Delete are only available to an administrator.New Create a new prole with default settings. Assign a unique name (a string of up to 32 characters). Edit prole settings using other Prole window selections.Rename Change the prole name to one that is not as-signed to another prole.Delete Delete a non-active prole. You cannot delete an active prole.Scan Tap to view a list of APs that are broadcasting SSIDs;selectanSSIDandcreateaproleforit.See “Using Scan to Create a Prole” for more information.Radio Select a radio attribute from the list on the le to view its value or setting in the box on the right. Only an administra-tor can edit these values or settings. See “Radio Settings” for more information.Security Values for the two primary security attributes, EAP type and encryption type, are displayed in separate drop-down lists with the current values highlighted. Only an administrator can edit these security settings. See “Security Settings” for more information.• Encryption - When the administrator selects an encryption type that requires the denition of WEP keys or a pre-shared key (PSK), the WEP keys/PSKs button becomes active. Tap WEP keys/PSKs to dene WEP keys or a PSK.• EAP Type - When the administrator selects an EAP type, the Credentials button becomes active. Tap Credentials to dene authentication credentials for the selected EAP type.Save Changes To save changes for the selected prole, you must tap Com-mit. If you make changes without tapping Commit and attempt to move to a dierent SCU window, a warning mes-sage displays and provides the option of saving your changes before you leave the Prole window.
986.0 Summit Radio6.1.2.1 Radio SettingsElement DescriptionSSID Use the drop-down menu to select the prole to be viewed or edited. Only an administrator can edit a prole.Client Name Actions included New, Rename, Delete, and Scan. New, Rename, and Delete are only available to an administrator.New Create a new prole with default settings. Assign a unique name (a string of up to 32 characters). Edit prole settings using other Prole window selections.Rename Change the prole name to one that is not as-signed to another prole.Delete Delete a non-active prole. You cannot delete an active prole.Scan Tap to view a list of APs that are broadcasting SSIDs;selectanSSIDandcreateaproleforit.See “Using Scan to Create a Prole” for more information.Power Save Select a radio attribute from the list on the le to view its value or setting in the box on the right. Only an administra-tor can edit these values or settings. See “Radio Settings” for more information.Tx Power Values for the two primary security attributes, EAP type and encryption type, are displayed in separate drop-down lists with the current values highlighted. Only an administrator can edit these security settings. See “Security Settings” for more information.• Encryption - When the administrator selects an encryption type that requires the denition of WEP keys or a pre-shared key (PSK), the WEP keys/PSKs button becomes active. Tap WEP keys/PSKs to dene WEP keys or a PSK.• EAP Type - When the administrator selects an EAP type, the Credentials button becomes active. Tap Credentials to dene authentication credentials for the selected EAP type.Bit Rate To save changes for the selected prole, you must tap Com-mit. If you make changes without tapping Commit and attempt to move to a dierent SCU window, a warning mes-sage displays and provides the option of saving your changes before you leave the Prole window.Radio Mode Use of 802.11a, 802.11g, 802.11b, and 802.11n frequencies and data rates when interacting with AP, or use of ad hoc mode to associate to a client radio instead of an AP. When SCU operates with a Summit 802.11g radio, an administrator can select from among the following Radio Mode values:• Value:– B rates only - 1, 2, 5.5, and 11 Mbps– G rates only - 6, 9, 12, 18, 24, 36, 48, and 54 Mbps– BG rates full - All B and G rates– BG Subset - 1, 2, 5.5, 6, 11, 24, 36, and 54 Mbps. is should only be used with Cisco APs running IOS in au-tonomous mode (without controllers). For Cisco APs that are tied to controllers and for non-Cisco APs, Summit recommends BG rates full.– Ad Hoc - When selected, the Summit radio uses ad hoc mode instead of infrastructure mode. In infrastructure mode, the radio associates to an AP. In ad hoc mode, the radio associates to another client radio that is in ad hoc mode and has the same SSID and, if congured, static WEP key.• Default - BG rates fullRadio Mode(cont’d)When SCU operates with a Summit 802.11a/g radio, an administrator can select from among the following Radio Mode values:• Value:– B rates only - 1, 2, 5.5, and 11 Mbps– G rates only - 6, 9, 12, 18, 24, 36, 48, and 54 Mbps– BG rates full - All B and G rates– A rates only - 6, 9, 12, 18, 24, 36, 48, and 54 Mbps (same as G rates)– ABG rates full - All A rates and all B and G rates, with A rates (the .11a radio) preferred. See “Preferred Band for 802.11a/g Radio” for more information.– BGA rates full - All B and G rates and all A rates, with B and G rates (the .11g radio) preferred. See “Preferred Band for 802.11a/g Radio” for more information.– BG Subset - 1, 2, 5.5, 6, 11, 24, 36, and 54 Mbps. is should only be used with Cisco APs running IOS in au-tonomous mode (without controllers). For Cisco APs that are tied to controllers and for non-Cisco APs, Summit recommends BG rates full.– Ad Hoc - When selected, the Summit radio uses ad hoc mode instead of infrastructure mode. In infrastructure mode, the radio associates to an AP. In ad hoc mode, the ra-dio associates to another client radio that is in ad hoc mode and has the same SSID and, if congured, static WEP key.• Default - ABG rates fullAuth Type 802.11 authentication type, used when associating to AP.• Value - Open, shared-key, or LEAP (Network-EAP)• Default - OpenNote: For a Cisco explanation of 802.11 authentication us-ing Open and Network-EAP, see: http://www.cisco.com/en/US/products/hw/wire-less/ps4570/products_configuration_exam-ple09186a00801bd035.shtml. e Summit Client Utility refers to Network-EAP as LEAP.6.1.2.2 Preferred Band for 802.11a/g RadioWhen the Radio Mode value is ABG rates full or BGA rates full, one band (5 GHz for ABG or 2.4 GHz for BGA) is preferred over the other. When trying to associate to an AP, the radio considers APs in the pre-ferred band. If the radio is able to associate to one of these APs, then the radio will not try to associate to an AP in the other band. e only time that the radio attempts to associate to an AP in the non-preferred band is when the radio is not associated and cannot associate in the preferred band. When roaming, the radio considers only APs in the current band (the band in which the radio is currently associated). When an admin-istrator tries to create or edit a prole, SCU determines which radio is operating in the device and populates the available radio mode values ac-cording to the radio type. Suppose a prole created for an 802.11a/g card is loaded on a device with an 802.11g card. If a radio mode value of A rates only, ABG rates full, or BGA rates full was set in the prole, then SCU displays a value of BG rates full. If the administrator does not save any changes to the prole, then SCU leaves the prole, including the radio mode, unchanged. If the administrator saves any changes to the prole, then SCU saves the radio mode value as BG rates full.6.1.2.3 Ad HocIf the administrator selects Ad Hoc for radio mode, then the Summit radio uses ad hoc mode instead of infrastructure mode. In infrastruc-ture mode, the radio associates to an AP. In ad hoc mode, the radio as-sociates to another client radio that is in ad hoc mode and has the same SSID and, if congured, static WEP key.
996.0 Summit Radio6.1.2.4 Security SettingsEAP type - Extensible Authentication Protocol type used for 802.1X au-thentication to AP.Value - None, LEAP, EAP-FAST, PEAP-MSCHAP, PEAP-GTC, PEAP-TLS, EAP-TLS, EAP-TTLSDefault - NoneCredentials - Authentication credentials for the selected EAP type. See 6.1.2.6 EAP Credentials for more information.Encryption - Type of encryption (and decryption) used to protect transmitted data. See “Encryption - Cisco TKIP” and “Encryption - WPA Migration Mode and WPA2 Mixed” for more information.• Value:– None - No encryption.– WEP - WEP with up to four static keys(40-bit or 128-bit in ASCII or hex) dened under WEP/PSK Keys.– WEP EAP - WEP with key generated during EAP authentication.– CKIP - WEP with up to four static keys(40-bit or 128-bit in ASCII or hex) dened under WEP/PSK Keys, plus Cisco TKIP and/or Cisco MIC, if congured on AP.– CKIP EAP - WEP with key generated during EAP authentication, plus Cisco TKIP and/or Cisco MIC, if congured on AP.– WPA-PSK (WPA Personal) - TKIP with PSK (ASCII passphrase or hex PSK) dened under WEP/PSK Keys.– WPA-TKIP(WPA Enterprise) - TKIP with key generated during EAP authentication.– WPA CCKM(WPA Enterprise) - TKIP with key generated during EAP authentication and with Cisco key management protocol for fast reauthentication.– WPA2-PSK with PSK (ASCII passphrase or hex PSK) dened un-der WEP/PSK Keys.– WPA2-AES (WPA2 Enterprise) - AES with key generated during EAP authentication.– WPA2 CCKM (WPA2 Enterprise) - AES with key generated dur-ing EAP authentication and with Cisco key management protocol for reauthentication.Note: For ABGN radios, CKIP and CKIP EAP are unavail-able. WEP and WEP EAP are the defaults.• Default:None6.1.2.5 Using Scan to Create a ProleWhen you tap Scan on the Prole window, SCU displays a list of APs that are broadcasting their SSIDs:e result shows an AP’s SSID, its received signal strength indication (RSSI), and whether or not data encryption is in use (true or false). If more than one AP appears, the list can be sorted by tapping on the col-umn headers. If the scan nds more than one AP with the same SSID, the list displays the AP with the strongest RSSI and the least security. Every ve seconds, the Scan window updates the RSSI value for each of the APs in the list. To scan for new APs and view an updated list, tap the Refresh button.An administrator in SCU can create a prole for any SSID in the list. To do so, either double-tap the row for the SSID or tap the row and tap Congure.
1006.0 Summit RadioSCU will display a dialog box such as the one shown below:If you tap the Yes button on the dialog box, then SCU will create a pro-le for that SSID, with the prole name being the same as the SSID (or the SSID with a sux such as “_1” if a prole with the SSID as its name exists already). If the AP is using WEP, then SCU will open a dialog box in which you can specify WEP keys. If the AP is using EAP, then SCU will open a dialog box in which you can specify login credentials for the EAP type (which SCU assumes is LEAP). Aer you enter information on a dialog box, you will return to the SCU Prole window, where you can view and edit prole settings. If you make any changes, then you must tap the Commit button to save them.
1016.0 Summit Radio6.1.2.6 EAP Credentialse 802.1X authentication types PEAP, EAP-TTLS, and EAP-TLS rely upon information in digital certicates that are created by a certicate authority, or CA. To enable a client device to validate (or authenticate) the server used for PEAP, EAP-TTLS, or EAP-TLS authentication, you must provision a root CA certicate and distribute it to that client. You can store the CA certicate in a device’s Microso certicate store or in a directory with a path that you specify as the value for Certs Path on the SCU Global window. If you don’t specify a Certs Path value, then SCU uses for the Certs Path value the path to the certs directory that is o the SCU folder. For EAP-TLS you also must generate a user certicate for eachclient;thatusercerticatemustbestoredintheMicrosocerticatestore on the client.Instead of using digital certicates, EAP-FAST relies upon strong shared-secret keys that are unique to users. ese secrets are called protected EAP-Type User Password CA Cert ValidateServerUser MS Store OthersLEAP Username or Domain/Username (up to 64 characters)Password (up to 32 characters)EAP-FAST Username or Domain/Username (up to 64 characters)Password (up to 32 characters)•PACFilename(upto32 characters)•PACPassword(upto32 characters)PEAP-MSCHAP Username or Domain/Username (up to 64 characters)Password (up to 32 characters)Filename (up to 32 char-acters)See Note on CA Cert FieldSee Note on Validate Server CheckboxSee Note on Use MS store CheckboxPEAP-TGC Username or Domain/Username (up to 64 characters)Password (up to 32 characters)Filename (up to 32 char-acters)See Note on CA Cert FieldSee Note on Validate Server CheckboxSee Note on Use MS store CheckboxPEAP-TLS Username or Domain/Username (up to 64 characters)Password (up to 32 characters)Filename (up to 32 char-acters)See Note on CA Cert FieldSee Note on Validate Server CheckboxSee Note on Use MS store CheckboxEAP-TTLS Username or Domain/Username (up to 64 characters)Password (up to 32 characters)Filename (up to 32 char-acters)See Note on CA Cert FieldSee Note on Validate Server CheckboxSee Note on Use MS store CheckboxEAP-TLS Username or Domain/Username (up to 64 characters)Filename (up to 32 char-acters)See Note on CA Cert FieldSee Note on Validate Server CheckboxSee Note on Use MS store CheckboxUser CertSee Note on User Certaccess credentials (PACs) and can be created automatically or manually. With automatic or in-band provisioning, the PAC is created and distrib-uted to the client device in one operation. With manual or out-of-band provisioning, the PAC is created in one step and then must be distributed to the client device separately. SCU supports PACs created automatically or manually. When you create a PAC manually, you must load it to the directory identied by the Certs Path global setting. Be sure that the PAC le does not have read-only permissions set, or SCU will not be able to use the PAC.ere are no default values for credentials. If the credentials are not speci-ed in the prole then, when the radio tries to associate using that prole, Summit soware will display a dialog box that prompts the user to enter the credentials. Summit soware will populate the dialog box with the username and password supplied for the previous EAP authentication.Note on CA Cert Field: is is the lename of the root certicate authority digital certicate. Leave this blank if the Use MS Store checkbox is checked.Note on Validate Server Checkbox: Check this if using a CA certicate to validate an authentication server. When this is checked, a certicate lename must be entered in the CA Cert eld or check the Use MS store checkbox.Note: Summit strongly recommends the use of server validation with PEAP-GTC.Note on Use MS Store Checkbox: Check this if the Microso certicate store should be used for a CA certicate. is is applicable only when Validate Server is checked.Note on User Cert: Tap the “...” button to select a user (or station) certicate fromtheMicrosocerticatestore.Donotenteralename;theusercerticatemust reside in the Microso certicate store. When browsing for a certicate, the pop-up box displays Issued By and Issued To.Of the seven EAP types supported by SCU, all but EAP-FAST and LEAP rely upon information in digital certicates that are created by a certicate authority (CA). To enable a station device to authenticate the server, provide a root CA certicate and distribute it to that station. e CA certicate can be stored in Notes for EAP Credentialsa unit’s Microso certicate store or in a specied directory (see Certs Path for additional information regarding a specied directory).Note: For EAP-TLS, the user must also generate a user certicate for each station. e user certicate must be stored in the Microso certicate store on the station. EAP-FAST relies upon strong shared-secret keys that are unique to users (rath-er than digital certicates). ese keys are called protected access credentials (PACs) and can be created automatically or manually. With automatic or in-band provisioning, the PAC is created and distributed to the station device in one operation. With manual or out-of-band provisioning, the PAC is created in one step and must then be distributed to the station device separately.SCU supports PACs created automatically or manually. When the user creates a PAC manually, it must be loaded into the directory identied by the Certs Path global setting. Be sure that the PAC le does not have read-only permissions set, or SCU will not be able to use the PAC.Note: If the user enters a PAC lename in the SCU eld, manual provisioning is used. If the user omits the PAC lename, automatic provisioning is used.
1026.0 Summit RadioElement DescriptionProle e active prole.Status Indicates the current status of the Summit radio. Potential values include:Down e radio is not recognized by Summit soware, possibly because the radio is not installed properly.Disabled e radio has been disabled because Disable Radio on the SCU Main window has been tapped. To enable the radio, tap Enable Radio on the SCU Main window.Not As-sociated e radio is not associated to an AP, possibly because no AP for the active prole is in range.Associ-atede radio is associated to an AP. If the radio is not sending or receiving from the AP, then:• IfWEP isbeingused,then oneof the WEPkeys in the active prole is invalid.• If WPA-PSK or WPA2-PSK is being used,then the PSK or password is invalid.• IfWPA-EnterpriseorWPA2-Enterpriseisbe-ing used, then the radio did not complete EAP authentication successfully.<EAP type> Authenti-catede radio is associated to an AP and has completed EAP authentication successfully.Device Information• Client name, if dened in active prole• IP address• MAC address6.1.2.7 Encryption6.1.2.7.1 Cisco TKIPIf the active prole has an Encryption setting of CKIP or CKIP EAP, then the Summit radio will associate or roam successfully to an AP is cong-ured with:• eSSIDandotherRFsettingsoftheactiveprole• eauthenticationmethodoftheactiveprole• ForWEP,thestaticWEPkeysoftheactiveprole• Anyofthefollowingencryptionsettings:– WEP only (no CKIP or CMIC)– WEP with CKIP– WEP with CMIC– WEP with CKIP and CMIC6.1.2.7.2 WPA Migration Mode and WPA2 Mixed ModeSummit radios support two special AP settings: WPA Migration Mode and WPA2 Mixed Mode. WPA Migration Mode is a setting on Cisco APs that enables both WPA and non-WPA clients to associate to an AP using the same SSID, provided that the AP is congured for Migration Mode (WPA optional with TKIP+WEP128 or TKIP+WEP40 cipher). In other words, WPA Migration Mode means WPA key management with TKIP for the pairwise cipher and TKIP, 128-bit WEP, or 40-bit WEP for the group cipher. When WPA Migration Mode in use, you can select WPA TKIP or WEP EAP for your Summit radio encryption type.WPA2 Mixed Mode operation enables both WPA and WPA2 clients to associate to an AP using the same SSID. WPA2 Mixed Mode is dened by the Wi-Fi Alliance, and support for the feature is a part of Wi-Fi certication testing. When WPA2 Mixed Mode is congured, the AP advertises the encryption ciphers (TKIP, CCMP, other) that are avail-able for use, and the client selects the encryption cipher it wants to use. In other words, WPA Mixed Mode means WPA key management with AES for the pairwise cipher and AES or TKIP for the group cipher. When WPA2 Mixed Mode in use, you can select WPA2 AES or WPA TKIP for your Summit radio encryption type.6.1.2.8 ThirdPartyCongIf the prole named ThirdPartyCong is selected as the active pro-le, then SCU works in tandem with WZC or another third-party appli-cation for conguration of all radio and security settings for the radio. e third-party application must be used to dene the SSID, Auth Type, EAP Type, and Encryption settings. SCU can be used to dene the Cli-ent Name, Power Save, Tx Power, Bit Rate, and Radio Mode settings. ose SCU prole settings, all SCU global settings, and the third-party application settings are applied to the radio when irdPartyCong is selected as the active prole and a power cycle is performed.On some devices that run Pocket PC or Windows Mobile, the radio will not associate if WPA with pre-shared keys, or WPA-PSK, is used with WZC. If that is the case for your device, then to use WPA-PSK you must use an SCU prole other than irdPartyCong.6.1.2.9 EAP-FASTe 802.1X authentication types PEAP and EAP-FAST use a client-server security architecture that encrypts EAP transactions within a TLS tunnel. PEAP relies on the provisioning and distribution of a digital certicate for the authentication server. With EAP-FAST, tunnel estab-lishment is based upon strong shared-secret keys that are unique to us-ers. ese secrets are called protected access credentials (PACs) and can be created automatically or manually. With automatic or in-band pro-visioning, the PAC is created and distributed to the client device in one operation. With manual or out-of-band provisioning, the PAC is created in one step and then must be distributed to the client device separately.SCU supports PACs created automatically or manually. When you cre-ate a PAC manually, you must load it to the certs directory on the device that runs SCU. Be sure that the PAC le does not have read-only permis-sions set, or SCU will not be able to use the PAC.Note: If you enter a PAC lename in the SCU eld, manual provision-ing is used. If you omit the PAC lename, automatic provision-ing is used.6.1.3 Status Windowe Status window provides status information on the radio. A sample Status window is shown below:
1036.0 Summit RadioAP Information• Name• IP address• MAC address• Beacon period: Amount of time between AP beacons in Kilo-microseconds, where one Ksec equals 1,024 microseconds• DTIM interval: A multiple of the beacon period that species how oen the beacon contains a delivery trac indication message(DTIM), which tells power-save client devices that a packet is waiting for them (e.g. a DTIM interval of 3 means that every third beacon contains a DTIM)ConnectionInformation• Channel• Transmit power• Data (bit) rate• Signal strength (RSSI), displayed graphically and in dBm– A green color indicates that the RSSI for the current AP is stronger than -70 dBm, which means that the Summit radio should operate consistently at 54 Mbps– A yellow color indicates that the RSSI for the current AP is stronger than -90 dBm but not stronger than -70 dBm, which means that a Summit radio will operate at 802.11g or 802.11a data rates that are less than 54 Mbps– A red color indicates that the RSSI for the current AP(to which the radio is associated) is -90 dBm or weaker, which means that a Summit 802.11b/g radio will operate at 802.11b data rates only• Signal quality (%), a measure of the clarity of the signal, dis-played graphically and in dBm -- is value will be lower with a irdPartyCong prole (under Windows Zero Con-g) than with a standard prole6.1.4 Diags WindowA sample Diags, or troubleshooting, window is shown below: Note: When a ping initiated from the Diags window is active, the Sta-tus window displays a ping indicator consisting of two lights thatashgreen(forasuccessfulping)orred(foranunsuccess-ful ping).Element Description(Re)connect Initiate a reconnect of the radio: Disable and enable the radio, apply (or reapply) the current prole, attempt to as-sociate to the wireless LAN, and attempt to authenticate to the wireless LAN. SCU logs all activity in the output area at the bottom of the Diags window.Release / RenewObtain a new IP address through DHCP release/renew. SCU logs all activity in the output area at the bottom of the Diags window.Start Ping / Stop PingStart a continuous ping to the address in the edit box next to the button. Once the button is tapped, its name and function changes to Stop Ping. Pings continue until you tap Stop Ping, move to a dierent SCU window (other than Diags or Status), exit SCU, or remove the radio.Note: If your device has both a Summit radio and another network adapter active, then pings may go out over the non-Summit network adapter.Note: e access point’s IP address is the default for a ping although any valid IP address can be manually en-tered.Diagnostics Attempt to (re)connect to an access point and provide a more thorough dump of data than is obtained with (Re)connect. e dump includes radio state, prole settings, global set-tings, and a BSSID list of access points in the area.Save To... Indicate where you want to save the diagnostics le.Tap Save To... to open the Save As window. From here, you can change the SDC diagnostics le name, the folder in which SCU saves the le, the format in which the le is saved (the le type), and the location of the saved le (Main memory or System).6.1.5 Global WindowGlobal settings include radio and security settings that apply to all proles and settings that apply to SCU itself. An administrator can dene and change most global settings on the Global window in SCU:Here are the functions available on the Diags window:
1046.0 Summit RadioTerms DenitionsRoam Trigger When moving average RSSI from current AP is weaker than Roam Trigger, radio does a roam scan where it probes for an AP with a signal that is at least Roam Delta dBm stronger.• Value:-50,-55,-60,-65,-70,-75,-80,-85,-90,orCustom(seenote on Custom below the list)• Default:-70Roam Delta When Roam Trigger is met, second AP’s signal strength (RSSI) must be Roam Delta dBm stronger than moving average RSSI for current AP before radio will attempt to roam to second AP.• Value:5,10,15,20,25,30,35,orCustom(seenoteonCustombelow the list)• Default:10Roam Period Aer association or roam scan (with no roam), radio will col-lect RSSI scan data for Roam Period seconds before consider-ing roaming.• Value:5,10,15,20,25,30,35,40,45,50,55,60,orCustom(see note on Custom below the list)• Default:10BG Channel SetDenes the 2.4 GHz channels to be scanned when the radio is contemplating a roam and to determine what APs are available:• Value: Full (all channels); 1,6,11 (the mostcommonly used2.4GHzchannels);1,7,13(forETSIandTELECradiosonly);or Custom (see note on Custom below the list)• Default:FullDFS Channels Support for 5 GHz (802.11a) channels where support for dynamic frequency selection (DFS) is required.• Value:On,O,OptimizedNote: When set to Optimized and scanning for the rst time, the radio scans all active channels and all available DFS channels. From this scan, the radio creates and maintains a list of up to three DFS chan-nels where beacons were detected. During subse-quent scans, the radio still scans all active channels but only scans the DFS channels listed from the rst scan (where beacons were detected).When the radio loses or resets the connection, the radio re-turns to scanning all available DFS channels as it did when scanning for the rst time aer being set to Optimized. From this scan, the radio again creates a list of DFS channels where beacons were detected.Note: e Optimized setting is not supported in the MS-D30AG and SSD30AG radios. If DFS Channels is set to Optimized directly in the registry, the setting will function as On (versus Optimized).• Default:FullDFS Scan TimeBecause passive scanning consumes a longer period of time, this feature enables you to determine the dwell (listen) time when passively scanning on a DFS channel.• Value:Anumberbetween20-500milliseconds(ms)• Default:120msNote: When decreasing the scan time (to a value lower than the default) for DFS channels, corresponding changes in the infrastructure’s beacon period are recommend-ed. For optimal performance and reliability, Summit recommends a dwell time that is 1.5 times that of the beacon period. For example, if the DFS scan time is set to 30 ms, the beacon period should be adjusted to 20 ms.Note: If you adjust this parameter directly in the registry, and congure it to a number outside of the 20-500 ms range, the setting value will return to the default (120 ms).Ad Hoc Chan-nele channel to be used for an ad hoc connection if the active prole has a Radio Mode value of “Ad Hoc”• Value:Oneofthe2.4GHzchannels(1-14)orUNII-1channels(36, 40, 44, 48) -- If you select a channel that is not supported by your radio, then SCU uses the default value for this setting.• Default:1Aggressive ScanWhen this setting is On and the current connection to an AP becomes tenuous, the radio scans for available APs more aggres-sively. Aggressive scanning complements and works in conjunc-tion with the standard scanning that is congured through the Roam Trigger, Roam Delta, and Roam Period settings. Summit recommends that the Aggressive Scan global setting be On un-less there is signicant co-channel interference because of over-lapping coverage from APs that are on the same channel.• Value:OnorO• Default:OnCCX Support Use of Cisco information element (IE) and CCX version num-ber;supportforCCXfeatures.• Value:– Full:UseCiscoIEandCCXversionnumber;supportallCCX features– Optimized: UseCisco IE andCCX versionnumber; sup-port all CCX features except AP-assisted roaming, AP-spec-ied maximum transmit power, and radio management– O: Do not use Cisco IE and CCX version number• Default:OptimizedNote: For 30AG (MSD30AG and SSD30AG) radio modules, this parameter is disabled. e default is Optimized.WMM Use of Wi-Fi Multimedia Extensions, also known as WMM.• Value:On,O• Default:ONote: For ABGN radio modules, this parameter is disabled.Auth Server Type of authentication server being used for EAP.• Value:– Type 1: Cisco Secure ACS or another server that uses PEAPv1 for PEAP with EAP-MSCHAPV2 (PEAP-MSC-HAP)– Type 2: A dierent authentication server, such as Juniper Networks Steel Belted RADIUS, that uses PEAPv0 for PEAP-MSCHAP• Default:Type1TTLS Inner MethodAuthentication method used within secure tunnel created by EAP-TTLS:• Value:– Auto-EAP: Any available EAP method– MSCHAPV2– MSCHAP– PAP– CHAP– EAP-MSCHAPV2• Default:Auto-EAPPMK Caching When WPA2 is in use, type of Pairwise Master Key (PMK) caching to use—See the section on PMK Caching.• Value:StandardorOPMK• Default:StandardNote: When switching from Standard to OPMK, you must initiate a suspend resume of the device. Only tapping Commit does not cause the change to take eect.e following radio global settings, which apply to all conguration pro-les, can be changed in SCU:
1056.0 Summit RadioFrag Thresh If packet size (in bytes) exceeds threshold, then packet is frag-mented• Value:Anintegerfrom256to2346• Default:2346Note: For 30AG (MSD30AG and SSD30AG) radio modules, this parameter is disabled.RTS Thresh Packet size above which RTS/CTS is required on link• Value:Anintegerfrom0to2347• Default:2347Note: For 30AG (MSD30AG and SSD30AG) radio modules, this parameter is disabled.RX Diversity How to handle antenna diversity when receiving data from AP• Value:– On-Start on Main: On startup use main antenna– On-Start on Aux: On startup, use auxiliary antenna– Main only: Use main antenna only– Aux only: Use auxiliary antenna onlyNote: Summit does not support the AUX antenna as a single-antenna solution.• Default:On-StartonMainNote: For ABGN and 30AG (MSD30AG and SSD30AG) ra-dio modules, this parameter is disabled.TX Diversity How to handle antenna diversity when transmitting data to AP• Value:– Main only: Use main antenna only– Aux only: Use auxiliary antenna onlyNote: Summit does not support the AUX antenna as a single-antenna solution.– On: Use diversity• Default:OnNote: For 30AG (MSD30AG and SSD30AG) radio modules, this parameter is disabled.LED UseofLED;availableonlywithMCF10G• Value:On,O• Default:OIf SCU displays a value of “Custom” for a global setting, then the op-erating system registry has been edited to include a value that is not available for selection on the Global window. Selecting Custom has no real eect. If SCU displays a value other than Custom and you select the value of Custom and tap Commit, then SCU reverts to the value that it displayed before you selected Custom.e following SCU global settings, which apply to SCU and other Sum-mit applications, can be changed in SCU:Hide Pass-wordsIf this is On, then SCU as well as EAP authentication dialog boxes mask passwords and other sensitive information, such as WEP keys.• Value:On,O• Default:OAdmin Pass-wordPassword that must be specied when Admin Login button pressed.• Value:Astringofupto64characters• Default:SUMMITCerts Path Directory where certicate(s) for EAP authentication and PAC les are housed.• Value:Avaliddirectorypathofupto64characters• Default:DependsondeviceAuth Time-outSpecies the number of seconds that Summit soware will wait for an EAP authentication request to succeed or fail. If authentication credentials are specied in the active prole and the authentication times out, then association will fail. If authentication credentials are not specied in the active pro-le and the authentication times out, then the user will be re-prompted to enter authentication credentials.• Value:Anintegerfrom3to60• Default:8 Ping PayloadAmount of data in bytes to be transmitted on a ping.• Value:32,64,128,256,512,1024• Default:32Ping Timeout msAmount of time in milliseconds that transpires without a re-sponse before ping request is considered a failure.• Value:Anintegerfrom1to30000• Default:5000Ping Delay msAmount of time in milliseconds between successive ping requests• Value:Anintegerfrom0to7200000• Default:1000When you change global settings and tap Commit, the changes take ef-fectimmediately.eonlyexceptionistheWMMsetting;ifyouchangeit, you must do a power cycle or suspend/resume on the device to cause the change to take eect. SCU provides you with a warning about the re-quired power cycle.) To cause global settings changes to take eect with-out a power cycle, Summit soware may have to reset and re-establish the WLAN connection between the Summit radio and the AP.If you make changes without tapping Commit and attempt to move to a dierent SCU window, SCU will display a warning message and give you the option of saving your changes before you leave the Global window.A few global settings can be dened or set only through a separate util-ity such as the Summit Manufacturing Utility, which Summit makes available only to device manufacturers and not to their customers.
1066.0 Summit Radio6.1.6 PMK CachingPMK caching is an alternative to CCKM supported with WPA2. e goal of PMK caching is to speed up roaming between APs by accomplishing 802.1X reauthentications without communicating with the authentica-tion server. When a client does an initial authentication to the WLAN infrastructure, both sides derive the information needed for reauthentica-tions.If there are no controllers, then standard PMK caching is used, and reau-thentication information is cached only on the initial AP. When the client tries to reauthenticate to that AP, the client and the AP use the cached information to do the four-way handshake to exchange keys. If there are controllers, then opportunistic PMK caching is used, and reauthentica-tion information is cached on the controllers. When the client tries to re-authenticate, the client and the controller behind the AP use the cached information to do the four-way handshake to exchange keys.Use the PMK Caching global setting to congure the type of PMK cach-ing supported by your infrastructure. If the Summit radio is congured for one type of PMK caching and the infrastructure supports the other type, then PMK caching will not work, and every roam will require a full 802.1X authentication that requires interaction with an authentication server.If the active prole has an Encryption setting of WPA2 CCKM, then the Summit radio ignores the PMK Caching global setting and attempts to use CCKM.
1077.0 BluetoothAt the top of the Main Window are Service Buttons. Aer you search for the services supported by a remote device, the supported services of the selected device will be highlighted.Local Device — Basic Operations:• Hoveryourmouseovertheredballtodisplaythelocaldevice’sBlue-tooth name and address.• ClickontheredballtostartorstopsearchingforBluetoothdevicesin range.• Right-clickontheredballtodisplayapop-upmenuofrelatedop-erations (e.g., General Inquiry, My Services, Security, etc.).Remote Devices — Icon Meanings• White—Idle.enormalstateofthedevice.• Yellow—Selected.Youhaveselectedthedevice.• Green—Connected.edeviceisconnectedtoyourlocaldevice.Remote Devices — Operations• Single-clicktoselect.• Double-clicktosearchfortheservicessupportedbythedevice.• Right-clicktodisplayapop-upmenuofrelatedoperations(e.g.,Re-fresh Devices, Pair Devices, Connect, etc.).Services — Icon Meanings• White—Idle.enormalstate.• Yellow—Available.eserviceisavailableontheselecteddevice.• Green—Connected.eserviceisactiveinaconnectionwiththeremote device.Services — Operations• Hoveryourmouseovertheserviceicontodisplaythenameoftheservice.• Single-clickontheserviceicontoconnect.• Right-clickontheserviceicontodisplayapop-upmenuofrelatedoperations.7.1 IntroductionBlueSoleil is a Windows-based soware from IVT that allows your Blue-tooth® enabled desktop or notebook computer to wirelessly connect to other Bluetooth enabled devices. BlueSoleil allows MS Windows users to wirelessly access a wide variety of Bluetooth enabled digital devices, such as cameras, mobile phones, headsets, printers, and GPS receivers. You can also form networks and exchange data with other Bluetooth enabled computers or PDAs.7.1.1 Bluetooth FunctionsIn order to connect and share services via Bluetooth wireless technol-ogy, two devices must support the same Bluetooth Prole(s) as well as opposite device roles (i.e., one must be the server, and the other must be the client).Bluetooth enabled devices oen support multiple proles, and if in-volved in multiple connections, can perform dierent device roles si-multaneously.BlueSoleil supports the following Bluetooth functions (Proles) in the following device roles:Notes:• OnlyoneHeadsetorAVHeadphoneconnectioncanexistatatime, since since there is only one virtual Bluetooth audio de-vice.• eHeadsetandAVHeadphoneProlesdonotworkonWin-dows 98SE or Windows Me.7.1.2 Main WindowBy default, BlueSoleil starts with the Main Window open. Use the Main Window to perform your primary connection operations. e Main Window displays the local device (red ball) as well as the remote devices detected in range.Note: For more complete information about the Main Window (in-cluding the icon meanings) as well as information about the Service Window and BlueSoleil menus, please refer to 7.4.Dierent icons distinguish dierent types of remote devices.Bluetooth Functions (Proles) Client ServerAV Headphone* √ √Basic Image Prole √ √Dial-Up Networking √Fax √File Transfer √ √Headset* √ √Human Interface Device √LAN Access √ √Object Push √ √Personal Area Networking √ √Printer √Serial Port √ √Synchronization √ √7.0 BlueTooth
1087.0 Bluetooth7.2 Basic Operations7.2.1 Start BlueSoleil1. Click on the BlueSoleil icon on your desktop, or go to: Start | Programs | IVT BlueSoleil | BlueSoleil2. e rst time BlueSoleil is launched, the Welcome to Bluetooth screen will appear. Assign your Windows system a name and device type, to be shown to other Bluetooth enabled devices. In most cases, you should leave the security setting checked. 3. Click OK.7.2.2 Search for Other Bluetooth En-abled DevicesBefore it can connect, your computer must rst detect other Bluetooth enabled devices in range.Initiate a Device Search1. Make sure that the Bluetooth enabled device you wish to connect to is turned on, with sucient battery power, and set in discoverable mode. Have any necessary passkeys ready. If necessary, you may also need to enable the service you want to use on the remote device. Refer to the remote device’s user documentation for instructions. If you haven’t done so already, you may also want to assign the de-vice a Bluetooth name. Refer to the device’s user documentation for instructions.2. In the Main Window, click on the red ball to start the device search. 3. Alternatively, click:My Bluetooth | My Device Inquiryor View | Refresh Devicesorpress F54. Aer a few seconds, an icon will appear around the center ball for each Bluetooth enabled device detected within the radio range.Note: • eMainWindowcandisplayonlyeightdiscovereddevicesata time. If BlueSoleil discovered more than eight devices, use the scroll bar to view the remaining devices discovered by BlueSoleil.• To sort the devices by device name, device address, or devicetype, click:View | Arrange Devices5. Wait several seconds until BlueSoleil reports the name of each device.6. If the device you want is not listed, make sure that the device is turned on and discoverable and try searching again. You have mul-tiple options for starting another search:• Ifyoustartanothersearchbydouble-clickingontheredballorclicking — My Bluetooth | My Device Inquiry or View | Refresh Devices then the list of previously detected devices will not be cleared.•IfyoustartanothersearchbypressingF5,thenthelistofprevi-ously detected devices will be cleared.7.2.3 Establish ConnectionNote: ese are generic instructions for any type of Bluetooth en-abled device. Refer to the instructions in 7.3 for specic de-tails for the type of service you plan to use.Normally, a connection is initiated from the client. Check the chart in 7.1.1 to verify which device role BlueSoleil supports for the service you wish to use.• Ontheserverside,starttheservice• Ontheclientside,initiatetheconnection7.2.3.1 Start the ServiceIf you would like to use your computer as a server in a Bluetooth con-nection, you must rst start (enable) the appropriate service(s) on your system.1. To access the Service Window, click:View | Service Window2. If the icon for a service is highlighted (yellow), then the service has already been started. If the icon is white, then you need to start the service in order to use it. Right-click the icon. In the pop-up menu, select Start Service. e icon should now be highlighted (yellow). Se-rial Port icons will also report which COM port is assigned to them.Note: • IconswillappearonlyforBluetoothfunctions(Proles)whichBlueSoleil supports in the Server device role. See chart in 7.1.1 Bluetooth Functions.• Dependingonyoursystem,multipleiconsforSerialCOMportsmay appear.3. Aer you have started the service in BlueSoleil, now you are ready to initiate the connection from the remote device. For instructions, refer to the user documentation for the remote device.7.2.3.2 Initiate the ConnectionIf you would like to use your computer as a client in a Bluetooth connec-tion, make sure that you have started (enabled) the service on the remote device. Otherwise, BlueSoleil will not be able to discover the service and connect to it. For instructions, refer to the device’s user documentation.1. Return to the Main Window by clicking:View | Main Window2. Double-click on the icon for the device you wish to connect to. Blue-Soleil will begin to search for information about which services the device supports.3. Aer the search, icons will be highlighted (yellow) at the top of the BlueSoleil Main Window for services that are supported by the de-vice. Verify that the service you want to use is supported.4. Right-click on the device icon. In the pop-up menu, click Connect, then select the service. BlueSoleil will start the connection. Depend-ing on the security settings of each device, you may need to enter the same passkey on each device in order to bond the two devices.5. A screen may appear asking if you want to set up automatic connec-tions. Click Yes or No.6. If you are connecting to a phone, your phone may ask if you want to
1097.0 Bluetoothask the BlueSoleil computer to your device list. Enter Yes and enter a passkey.7. When the devices have successfully connected, the device icon in the Main Window will turn green, and a green line will appear be-tween the red ball and the device icon. A red dot will travel along the green line from the client to the server. A signal strength icon will also appear next to the device icon. e BlueSoleil icon in the task tray will also turn green to indicate an active connection.Note: A red check mark will appear next to the name of any device that you have previously paired with your computer.8. Depending on which services you are using, additional screens may appear, and/or you may need to congure additional connection settings (e.g., user name, password, COM port number, etc.). Refer to the instructions in 7.3 for your specic service. Aer conguring the appropriate connection settings, you should be ready to use your application.9. To end a connection, in the Main Window, right-click on the icon for a connected device. In the pop-up menu, click Disconnect.Note: You can only disconnect this way if your computer is acting as a client device. If your computer is acting as a server device, then you can disconnect in BlueSoleil by clicking:View | Service Window then right-clicking on the service icon. In the pop-up menu, click Stop Service. Alternatively, you can disconnect from the remote device.7.2.4 Bluetooth SecurityTo modify your connection’s security settings, click: My Bluetooth | SecurityBlueSoleil oers three security levels:• Low (Security Mode 1, Non-secure) No security procedure is needed for connections.• Medium (Security Mode 2, Service level enforced security) Authentication or Authorization is requested when a specic service is accessed by other Bluetooth enabled devices. If two devices are connecting for the rst time, or if two devices do not have a trusted relationship, then the same passkey must be provided on both sides to complete the Authentication. is mode allows you to assign dif-ferent access rights for each service supported by the server device.• High (Security Mode 3, Link level enforced security) If either of two devices is in Mode 3, Authentication is requested whenever a link connection is initiated between two Bluetooth en-abled devices. e passkey must be provided on both sides to com-plete Authentication.Note: In Security Mode 2, the user can add each authenticated de-vice into a trusted device list to expedite future connections.7.3 Getting Started7.3.1 AV Headphonee AV Headphone Prole enables use of a Bluetooth enabled head-phone to listen to high-quality stereo music played on a computer.Typical Usage• ListentomusicusingaBluetoothenabledAVheadphone.Step 1: Connect to the AV headphone, following the instructions in 7.2.3.Step 2: Play music using media player soware on your computer. Music will transmit wirelessly to the headphone.7.3.2 Basic Imaginge Basic Imaging Prole (BIP) enables users to receive pictures from a Bluetooth enabled digital camera, mobile phone, or other compatible device. It also enables remote control of shooting, display, and other imaging functions.Typical Usage• Controlcameratotakepictures• ReceivepicturessentfromBIP-enableddigitaldevicesStep 1: Connect to the camera, following the directions in Section 7.2.4. A Bluetooth Camera Controller will appear.Step 2: Click the button to capture the image. e captured image will be transmitted to your computer and displayed.Receive PicturesStep 1: Assign the directory where you would like to save image les pushed from the client device. Click My Services | Properties. Click on the Basic Image Push tab. In the Set the image direc-tory eld, browse to select the le location. Click OK.Step 2: Start the BIP service, following the directions in 7.2.3.Step 3: Send pictures from the remote device. For instructions, refer to the user documentation for the remote device.7.3.3 Dial-up Networkinge Bluetooth Dial-up Networking (DUN) Prole enables users to wire-lessly dial-up to the Internet through a Bluetooth enabled modem or mobile phone that supports the DUN Prole.
1107.0 BluetoothTypical Usage•Dial-uptotheInternetviaaBluetoothenabledmobilephone.•Dial-uptotheInternetviaaBluetoothenabledmodem.Dial-up to the Internet via a Bluetooth enabled mobile phone.Step 1: Connect to the phone’s Dial-Up Networking Service, follow-ing the instructions in 7.2.3.Step 2: e Dial-Up Dialog will appear. Enter the dial-up number, User name, and Password. Make sure the correct dial-up number is entered, then click on the Dial button.Note: e default dial-up number *99***1# only works with certain GPRS phones and service providers in the United States. If necessary, enter the correct dial-up number for your Internet Service Provider (ISP).Note: Aer you successfully connect, a screen will ask if you would like to create a dial-up shortcut on your desktop. is would allow you to conveniently dial up and connect by simply click-ing on the shortcut, without having to manually start BlueSo-leil. Alternatively, aer starting BlueSoleil, you can start the shortcut by clicking Tools | My Shortcuts.Dial-up to the Internet via a Bluetooth enabled modem.Step 1: Connect to the modem’s Dial-Up Networking Service, follow-ing the instructions in 7.2.3.Step 2: e Dial-Up Dialog will appear. Enter the dial-up number, User name, and Password. Enter the correct dial-up number, then click on the Dial button.Note: e default dial-up number *99***1# does NOT work with modems. You need to enter the correct dial-up number for your Internet Service Provider (ISP).Step 3: Use your email, Internet browsing or other application that utilizes a dial-up connection.Note: Aer you successfully connect, a screen will ask if you would like to create a dial-up shortcut on your desktop. is would al-low you to conveniently dial up and connect by simply clicking on the shortcut, without having to manually start BlueSoleil.7.3.4 FA Xe Bluetooth Fax Prole enables users to send faxes from a computer via a Bluetooth enabled mobile phone or modem.Typical Usage• SendfaxviaaBluetoothenabledmobilephone.• SendFaxviaaBluetoothenabledmodem.Send fax via a Bluetooth enabled mobile phoneStep 1: Connect to the mobile phone’s fax service, following the di-rections in 7.2.3.Step 2: Use your fax soware to send the message.Send fax via a Bluetooth enabled modemStep 1: Connect to the modem’s fax service, as described in 7.2.3.Step 2: Start your fax soware. Congure your fax soware for the Bluelet Fax Modem (NOT the Bluelet Modem). Refer to your fax soware’s user documentation for instructions.Step 3: Use your fax soware to send the message.7.3.5 File Transfere File Transfer Prole (FTP) enables users to transfer les and/or folders between Bluetooth enabled laptops, desktops, PDAs, mobile phones, etc.Typical Usage• ConnecttoaBluetoothenabledmobilephoneandtransferlesorfolders to/from the phone.• ShareafolderonyourcomputerwithotherBluetoothenableddevices.• AccessasharedfolderonanotherBluetoothenableddevice.7.3.5.1 Connect to a Mobile PhoneStep 1: Connect to the mobile phone’s FTP service, following the in-structions in 7.2.3.Step 2: e phone’s folders are shown in a window. Users can copy/paste/delete les or folders.7.3.5.2 Share a Folder on Your Computer with other Bluetooth-Enabled DevicesSelect the folder to be used for le sharing and dene the remote user privileges.Step 1: Click:My Services | PropertiesStep 2: Click on the File Transfer tab. Share this folder: Browse to select the folder you would like to share. Share Permissions: Select Read and Write to allow oth-ers to copy, paste or delete les/folders in this folder. Select Read Only to allow others to only browse and copy les/fold-ers from this folder.Step 3: Start the FTP service in BlueSoleil, following the instructions in 7. 2.3. Do not initiate the connection in BlueSoleil.Step 4: Browse your computer from the remote device. For instructions, refer to the user documentation for the remote device. When the remote device attempts to connect to your computer, the Blue-tooth Service Authorization screen may appear. Click Yes.Step 5: Aer successfully connecting, the remote device can browse, copy, paste, and/or delete les on your computer, depending on the remote folder privileges you allowed. For instructions, refer to the user documentation for the remote device.
1117.0 Bluetooth7.3.5.3 Access a Shared Folder on Another Bluetooth Enabled DeviceStep 1: On the remote device, designate the folder/les to share. En-able le sharing on the remote device. For instructions, refer to the user documentation for the remote device.Note: If you do not enable le sharing on the remote device, BlueSoleil will not be able to discover the device’s le sharing service.Step 2: Start the FTP service and initiate the connection in BlueSoleil, following the instructions in 7. 2.3.Step 3: A Remote Shared Folder screen will appear, displaying shared les/folders on the remote device, Use the screen to browse, copy, paste, and/or delete les, depending on your folder privileges.7.3.6 Headsete Headset Prole enables users to use a Bluetooth enabled headset as wireless earplug or microphone.Typical UsageUse Headset as a device for audio input/output.Step 1: Connect to the Bluetooth enabled headset, following the di-rections in 7.2.3.Step 2: Play music on your computer, or chat using network meet-ing tools. You may need to press a multifunction button on your headset to transmit audio between the computer and the headset.Note: For most Bluetooth enabled headsets, aer you have success-fully connected for the rst time, you can quickly reconnect to BlueSoleil by simply pressing a multifunction button on the headset.7.3.7 Human Interface Devicee Bluetooth Human Interface Device (HID) Prole enables users to use Bluetooth enabled HID Devices such as keyboards, mice or joysticks to control your computer.Typical UsageConnect a Bluetooth enabled Mouse and a Keyboard to Your ComputerStep 1: Connect the Bluetooth enabled mouse to your computer, fol-lowing the instructions in 7.2.3.Step 2: Connect the Bluetooth enabled keyboard to your computer, following the instructions in 7.2.3. Before you can use Blue-Soleil to connect, you may need to press a button on the key-board to make it discoverable.Note:• ersttimethemouseorkeyboardisconnectedtothecom-puter, the Found New Hardware Wizard will automatically launch. In the rst screen of the wizard, DO NOT INSERT ANY CD, click Next. • Followallthescreensuntilthewizardiscompleted.Ifthewiz-ard reappears, cancel the wizard. e mouse or keyboard should be enabled.• e Bluetooth enabled mouse/keyboard can automatically re-connect to the computer aer successfully establishing the ini-tial connection.7.3.8 LAN Accesse Bluetooth LAN Access Prole (LAP) allows users to access a Local Area Network (LAN) via a Bluetooth enabled LAN access point.Typical Usage• AccessaLANviaaBluetooth-enabledLANAccessPoint(AP)• UseyourcomputerasaLANAccessPoint— Access a LAN via a Bluetooth-enabled LAN APStep 1: Connect to the LAN AP’s LAP service, following the instruc-tions in 7. 2.3.Step 2: In the Connect Bluetooth LAP Connection dialog, enter the user name and password if necessary. Click Connect.— Use the computer as a LAN AP (Advanced Users Only)Step 1: Start the Bluetooth LAN Access service on BlueSoleil, follow-ing the instructions in 7.2.3.Step 2: Specify any static IP addresses necessary for LAP clients. (Alternatively, you can use DHCP to have the system dynami-cally assign IP addresses). (1) In the Network Connections window, right-click Incom-ing Connection, then select Properties (Figure 3.3). (2) Select: Incoming Connections Properties | Networking -> Internet Protocol (TCP/IP) and click on the Properties button.
1127.0 Bluetooth (3) Select Specify TCP/IP addresses and enter the range of IP addresses assigned to LAP clients.7.3.9 Object Pushe Bluetooth Object Push Prole (OPP) enables users to send and re-ceive Personal Information Management (PIM) data objects (including messages, notes, calendar items, and business cards) to and from a Blue-tooth enabled PDA or mobile phone.e objects supported include:• Contacts(*.vcf)• Calendaritems(*.vcs)• Notes(*.vnt)• Messages(*.vmg)Typical Usage• PushobjectstoaBluetoothenabledmobilephoneorPDA• ReceiveobjectsfromaBluetoothenabledmobilephoneorPDANote: If you would like to push PIM objects to a PDA, make sure that the PDA is ready to receive a PIM object before you start. If necessary, enable Object Push on the PDA. For instructions, refer the PDA’s user documentation.7.3.9.1 Push Objects to a Bluetooth-Enabled Mobile Phoneere are two methods to push objects:Method 1: From BlueSoleil Main Window: Double-click on the mobile phone or PDA icon to browse for service information. e Object Push Service icon should be highlighted at the top of the screen. Right click the Object Push Service icon, and in the pop-up menu click Send My Card.• Send My Card: Send your default business card.• Get Card: Get the phone’s default business card.• Send Objects: Select objects (PIM les ending in .vcf, .vcs, .vnt, or .vmg) and send them to the phone.• Exchange cards: Have your computer and the phone to exchange their de-fault business cards.Method 2: From MS Outlook: (1) Select the contact that you would like to send. (2) In Outlook, click on the Push button on the toolbar, or click:File | Push (3) e Bluetooth Neighbors screen will appear. In the device list, select the phone or PDA that you wish to push the contact to. Click on the Push button.7.3.9.2 Receive Objects from a Bluetooth En-abled Mobile PhoneStep 1: Congure the parameters for the object push. From the Main Window, click My Services | Properties. Click on the Object Push tab.Step 2: Start the Object Push service, following the instructions in 7.2.3. Do not initiate a connection, only start the service so that your computer will be ready to receive objects.Step 3: Send objects from the phone. For instructions, refer to your phone’s user documentation.Notes:• BlueSoleil creates a Bluetooth folder (with Inbox and Outboxsubfolders) in your My Documents folder for use with Object Push. e Inbox is used to save objects received from other de-vices. e Outbox is used to save objects sent out from your com-puter.• YourcansetyourdefaultbusinesscardbyclickingMy Services | Object Push In the Send My Business Card eld, browse to select a contact as your default business card.7.3.10 Personal Area Networkinge Bluetooth Personal Area Networking (PAN) Prole enables PCs, laptops, PDAs, and other Bluetooth enabled devices to form either of two kinds of PAN networks. In a Group ad-hoc Network (GN), which functions as an isolated network, multiple PAN Users (PANUs) are linked together via a GN controller.Alternatively, a PAN can consist of multiple PANUs linked to a Network Access Point (NAP), which provides access to external Local Area Net-work (LAN) infrastructure. BlueSoleil supports all three of these device roles — GN (controller), PANU, and NAP.Typical Usage• Group Ad-hoc Network (Peer-to-peer networking) — One device
1137.0 Bluetoothacts as the GN, and others function as PANU devices. ese com-puters can visit each other or use an application based on TCP/IP.• AccessaLANviaaNetworkAccessPoint(ora ComputerActingas a NAP). Aer the computers connect to the NAP, they become members of the LAN and can directly communicate with other computers in the LAN.7.3.10.1 Connecting the PAN User (PANU)Step 1: Connect to the server’s Personal Area Network service, fol-lowing the instructions in 7.2.3.Step 2: Wait a few seconds for BlueSoleil to obtain and display your computer’s IP address.7.3.10.2 Conguring the NAP/GNClick Bluetooth Service | Properties and click on the Personal Area Net-work tab.Scenario 1 — Group Ad-hoc NetworkSelect Set up Bluetooth Personal Area Network and Enable DHCP Serv-er (Figure 3.9).A DHCP server will be started on the GN. e PANU can obtain an IP address automatically from this DHCP server if the PANU does not set static IP address for the BT Network Adapter.Scenario 2 — Access LAN via PAN-NAPSelect Access LAN Network and select a physical network adapter, through which the NAP connects to a LAN, as the LAN Adapter (Fig-ure 3.10).Scenario 3 — Access the Internet via NAPSelect Access Internet and select a physical network adapter, through which the NAP connects to Internet, as the WAN Adapter (Figure 3.11). It will automatically enables NAT (Network Address Translation, please refer to Windows Help Topic) function and a DHCP server.Note: e BT Network Adapter on the PANU side must be set to obtain an IP address automatically. e IP address is in the form of 192.168.2.xxx, such as 192.168.2.1.7.3.11 Printere Bluetooth Printer Prole (HCRP) enables your computer to connect to a Bluetooth enabled printer.Typical UsagePrint documents on a Bluetooth enabled Printer.Step 1: Connect to the printer’s printer service. (a) If your computer does not have the correct printer driv-ers installed, BlueSoleil will prompt you to do so. Install the
1147.0 Bluetoothdriver for the printer, and remember to set the printer port to the correct COM port number. To determine the correct COM port number, in the Main Window, right-click on the device icon. In the pop-up menu, select Status. (b) If the printer driver has been installed, a message indicates that the printer is ready.Step 2: Print documents using the Bluetooth enabled printer. In the ap-plication, be sure to select the correct printer and printer port.7.3.12 Serial Porte Bluetooth Serial Port Prole (SPP) provides PCs, laptops, PDAs, GPS receivers, cordless serial adapters, and other Bluetooth enabled devices with a virtual serial port, enabling them to connect with each other wirelessly via Bluetooth instead of with a serial cable.BlueSoleil supports four Bluetooth Serial Ports for outgoing connec-tions and two Bluetooth Serial Ports for incoming connections.Typical UsageConnect to other Bluetooth enabled devices via the Serial Port Connect to a PDA.Step 1: Connect to the PDA’s Serial Port service, following the in-structions in 7.2.3.Step 2: Use ActiveSync or any other application that uses a serial con-nection.Note:• SerialPortAuto-Connectionfunction Once a target device is assigned to a specic serial port, (e.g., COM5), whenever an application opens that serial port number, BlueSoleil will automatically connect to the target device. Simi-larly, whenever an application closes the Bluetooth serial port, BlueSoleil will stop the connection. To check which devices are assigned to which COM ports, click Tools | Congurations | Connect With.• SomeapplicationsonlyallowyoutousealimitedrangeofCOMport numbers. If the application does not allow you to use a COM port number assigned by BlueSoleil, you will not be able to use BlueSoleil with your application.7.3.13 Bluetooth Synchronizatione Bluetooth Synchronization (SYNC) Prole enables users to syn-chronize PIM objects on their computer with that of other Bluetooth enabled computers as well as Bluetooth enabled mobile phones, PDAs, and other devices.Four kinds of objects are supported:• Contacts(*.vcf)• Calendars(*.vcs)• Notes(*.vnt)• Messages(*.vmg)Supported MS Outlook versions: Outlook 2000, Outlook 2002 (xp), Outlook 2003.Typical UsageSynchronize your computer with a Bluetooth enabled mobile phone.Step 1: Connect to the mobile phone’s Synchronization service, fol-lowing the instructions in 7.2.3.Step 2: A synchronization dialog will appear (refer to Figure 3.12). Click on the Start button to synchronize. Contacts, calendars, notes and emails in MS Outlook will be synchronized with those on the phone.Note:• UserscanstartsynchronizationfromMSOutlookusingtheBlue-tooth Add-In menus and buttons installed with BlueSoleil.• BlueSoleil can act as synchronization server. Click My Services |Properties. Click on the Information Synchronization tab, and se-lect the type of PIM objects that you would like to synchronize.
1157.0 Bluetooth7.4 BlueSoleil User Guides7.4.1 BlueSoleil Environment7.4.1.1 Main Windowe Main Window displays the local device (red ball) and the remote devices detected in range. Connecting and disconnecting operations are conducted here. Connections are indicated by green dashed lines between the local device and connected remote devices.By default BlueSoleil starts with the Main Window open. To return to the Main Windows aer switching views, click View | Main Window.7.4.1.1.1 Local Bluetooth Devicee Local Bluetooth enabled device, known as “My Device,” represents the user’s computer that is running BlueSoleil.— Operations• Hoveryourmouseovertheredballtodisplaythelocaldevice’sBlue-tooth name and address.• ClickontheredballtostartorstopsearchingforBluetoothdevicesin range.• Right-clickontheredballtodisplayapop-upmenuofrelatedop-erations (e.g., General Inquiry, My Services, Security, etc.).7.4.1.1.2 Remote Bluetooth DevicesRemote devices are other Bluetooth enabled devices that are in the radio range of your local device. BlueSoleil uses dierent icons to indicated dierent types of remote devices.Personal ComputerLaptopModem Mobile PhonePDA LAN Access PointKeyboard MouseMicrophone HiFi AudioLoud SpeakerHeadsetPrinter ScannerFax CameraGame Con-trollerServerUnknown Device— Icon MeaningsRemote devices can be in any of three states, which BlueSoleil indicates with dierent colors.• White—Idle.enormalstateofthedevice.• Yellow—Selected.Youhaveselectedthedevice.• Green—Connected.edeviceisconnectedtoyourcomputer.— Operations• Single-clickontheicontoselect.• Double-clickontheicontosearchfortheservicessupportedbytheremote device.• Right-clickontheicontodisplayapop-upmenuofrelatedopera-tions (e.g., Refresh Devices, Pair Devices, Connect, etc.).7.4.1.1.3 Bluetooth Service Buttons of Remote DeviceService buttons at the top of the Main Window represent a range of Bluetooth services potentially supported by Remote Devices.PAN DUNSPP LAPFTP SYNCOPP HCRPHID FAXBIP AVHeadset— Icon Meaningsere are 3 states for the service icons, indicated by dierent colors.• White—Idle.enormalstate.• Yellow—Available.eBluetoothserviceisavailableontheselect-ed remote device.• Green—Connected.eBluetoothserviceisactiveinaconnectionwith the remote device.— Operations• Hoveryourmouseovertheserviceicontodisplaythenameoftheservice.• Single-clickontheserviceicontoconnect.• Right-clickontheserviceicontodisplayapop-upmenuofrelatedoperations.7.4.1.2 Service Windowe Service Window displays the local Bluetooth services, (i.e., the Blue-tooth services supported by BlueSoleil). Use the Service Window to start and stop services, as well as to congure service properties. To access the Service Window, click:View | Service Window
1167.0 BluetoothLocal Service Liste Local Service List displays all of the Bluetooth services supported by the local computer. Use this screen to start/stop services.PAN SPPOPP FTPSYNC LAPAV BIPHeadset AG— Icon Meaningsere are 3 states for the local Bluetooth services, indicated by dierent icon colors.• White–Idle.eservicehasnotbeenstarted.• Yellow–Started.elocalBluetoothservicehasbeenstarted.• Green–Connected.Someremotedevicehasconnectedtotheservice.— Operations• Single-clickontheicontoselecttheservice.• Double-clickontheicontoStart/Stopaservice.• Right-clicktodisplayapop-upmenuofrelatedoperations.7.4.1.3 MenusBlueSoleil contains the following six menus:• FileMenu• ViewMenu• MyBluetoothMenu• MyServicesMenu• ToolsMenu• HelpMenuFile MenuHide — Hide the BlueSoleil window. Connections can still run when the window is hidden.Always on Top — Keep the BlueSoleil window always on top.Exit — Exit BlueSoleil.You can also exit BlueSoleil by right-clicking on the task tray icon at the bottom of your screen. In the pop-up menu, click Exit.View MenuMain Window — Show the BlueSoleil Main Window.Service Window — Show the BlueSoleil Service Window.Arrange Devices — Arrange remote devices by Device Name, Device Address, or Device TypeRefresh Devices — Refresh the list of remote devices detected by Blue-Soleil.Note: If you select Refresh Devices, the list of previously detected devices will not be cleared. To initiate a new device search that will rst clear the list, press F5.My Bluetooth MenuBluetooth Device Inquiry -— Search for other Bluetooth enabled de-vices in range.Bluetooth Service Browsing — Browse for the services of the selected remote device.Security — Congure the security settings of the local device (e.g., pass-key requirements, data encryption, etc.).Properties — Congure the properties of the local device (e.g., device name, accessibility, etc.).My Services MenuStart Service — Start the selected local Bluetooth service.Stop Service — Stop the selected local Bluetooth service.Status — View the status of the selected local Bluetooth service.Properties — Congure the properties of the local Bluetooth services (e.g., automatic connections, shared le locations, etc.).Tools MenuMy Shortcuts — Display dialog Bluetooth Shortcuts.Connect: Connect the selected shortcut.Delete: Delete the selected shortcut.Find Device — Click to nd a device, by either of two search criteria:By Bluetooth Device Address:Enter a Bluetooth device address, in standard format (xx:xx:xx:xx:xx:xx), and click on the Find button. e device with the specied address will appear highlighted in the Main Window.By Name:Check the By Name box, enter the Name of the device, and click on the Find button. e device with the specied name will appear highlighted in the Main Window.Add New Device — Add a remote device by entering its Bluetooth de-vice address.Add Device From History — Add a remote device from the history list.Add: Add the selected device.Delete: Clear the selected device from the history list.Congurations->Connect With — If desired, assign a remote device to automatically connect with a Bluetooth serial port whenever an applica-tion opens the specied port.Assign: Assign a device to the selected port.Remove: Remove the Auto-Connection device assignment for the se-lected port.Congurations-> Unplug HID — Remove Human Interface Devices from BlueSoleil.Unplug: Unplug the selected HID device.When you rst connect the HID device to your computer, BlueSoleil sets up the devices so that they will automatically reconnect in case the connection is ever broken. Aer you unplug an HID device, it will no longer automatically reconnect to your computer.Bluetooth Device — Advanced hardware conguration, recommended for advanced users only. Please refer to 4.2 Hardware Conguration for more details.
1177.0 BluetoothHelp MenuContents and Index — Access BlueSoleil Online Help.About BlueSoleil — Information about your version of BlueSoleil.7.4.2 Device Congurations7.4.2.1 Hardware CongurationBlueSoleil supports the following kinds of Bluetooth radio adapters: USB and CF card.To access the hardware conguration screens, click Tools | Bluetooth Device…Bluetooth DeviceSelect the type of Bluetooth enabled device that you plan to use, either a USB adapter or a CompactFlash (CF) card.Advanced Conguratione Advanced Conguration page will be enabled only if you selected CF in the Bluetooth Device screen. Use the Advanced Conguration screen to congure detailed parameters including COM Port, Baud Rate, Byte Size, Parity, Stop Bits, and Flow Control.7.4.2.2 Properties CongurationTo congure the properties of your local device, click:My Bluetooth | Properties…General— Device Namee local device’s name, which will be shown to other Bluetooth enabled devices.— Device Typee device type of your local computer, (i.e., Desktop, Laptop or Server).— Device Addresse address of the local device. Every Bluetooth enabled device has a unique device.Accessibility— Connecting Mode• Connectable: Permits other Bluetooth enabled devices to connectwith your computer.• Non-Connectable:ProhibitsotherBluetoothenableddevicesfromconnecting with your computer.— Discovery Mode• General Discoverable: Permits other Bluetooth enabled devices todetect your computer.• Limited Discoverable: Permits other Bluetooth enabled devices todetect your computer with Limited Inquiry.• Non-Discoverable:ProhibitsotherBluetoothenableddevicesfromdetecting your computer.— Bonding Mode (Pairing Mode)• Accepts Bonding: Allow other Bluetooth enabled devices to pairwith your computer. If the other device initiates a pairing procedure with your computer, each device must enter the same passkey before the they will be paired.• Does Not Accept Bonding: Rejects pairing attempts initiated byother Bluetooth enabled devices.HardwareView information about your Bluetooth hardware.• Manufacturer:emanufacturerofthelocalBluetoothdevice.• HCIVersion:eHCIversionofthelocalBluetoothdevice.• HCIEdition:eHCIeditionofthelocalBluetoothdevice.• LMPVersion:eLMPversionofthelocalBluetoothdevice.• LMPSubversion:eLMPsubversionofthelocalBluetoothdevice.7.4.3 Security CongurationUse the Security Conguration screens to specify the security settings of your local device.7.4.3.1 Pair / Un-pair DevicesOnce a remote device has paired with your computer by exchanging passkeys, passkeys will no longer be required for further connections between your computer and the device.7.4.3.1.1 How to pair with another device— AutomaticallyIf a passkey is required for connection, the devices will be paired auto-matically the rst time they successfully exchange passkeys and con-nect. Aer a device has successfully paired with your computer, the re-mote device icon in the Main Window will have a red checkmark next to it.— ManuallyIn the Main Window, right click on the device icon, and in the pop-up menu, select Pair Device. In the Enter Bluetooth Passkey screen, enter the same passkey that you enter on the remote device. Aer a device has successfully paired with your computer, the remote device icon will have a red checkmark next to it.7.4.3.1.2 How to un-pair with another deviceIn the Main Window, right-click on the device icon, and in the pop-up menu, select Unpair. e red checkmark next to the device icon will disappear.7.4.3.2 General SecurityTo access the security conguration screen, click:My Bluetooth | Security…7.4.3.2.1 Security Level— LowIf checked, other devices will be able to access your device freely without entering a passkey.However, if the remote device requires a passkey to connect, then both devices need to exchange passkeys.— Mediume medium level provides service level security. You can assign the ap-propriate level of access for each specic service. For more details, see 4.3.4 Local Services Security.— HighIf checked, passkeys must be exchanged for every incoming and outgo-ing connection, unless the two devices have already paired in the past.
1187.0 Bluetooth7.4.3.2.2 Bluetooth Passkey— Set Default PasskeyUse this setting to create a default passkey for all connections. is saves you the eort of manually creating a passkey whenever one is required.7.4.3.2.3 Data Encryption— Enable Data EncryptionIf checked, the data transmitted will be encrypted.7.4.3.3 Managing Device PairingsTo access the device security conguration screen, click My Blue-tooth | Security and click on the Devices tab.— Paired Devicesis screen lists devices which have already paired with the local device.— Remove PairingClick to remove the pairing relationship between the selected device and the local device.— AuthorizationClick to select the local Bluetooth services that you wish to allow the se-lected paired device to use. A list of local services will appear. Select the services you wish to allow on the remote device, then click OK.Note: e screen will only list the local services that require authen-tication. e local services that do not require authentication can be accessed freely.e Authorization button is enabled only when the Security Level is set to Medium.7.4.3.4 Local Services SecurityTo access the local services security conguration screen, click:My Bluetooth | Security and click on the Services tab. You can only congure security for lo-cal services when the Security Level is set to Medium. (Set the Security Level in the General Security screen.)7.4.3.4.1 Local Services:— AuthenticationIf checked, a passkey is required whenever a remote device attempts to connect with this service.— EncryptionIf checked, data transmitted between devices for this service will be en-crypted.— AuthorizationClick to select the devices you wish to allow to use the selected service.In the Service Authorization screen, enter the following settings:— Trusted DevicesSelect to trust devices listed in this screen to use the selected service on your device.A device can freely access the service from your local device when trust-ed. Click Add/Remove to edit the device list.— Trust all devicesConnection requests will be accepted from every device.— Prompt user if the device is not trusted for this serviceIf a non-trusted device attempts to access the service, a dialog will ap-pear to allow you to accept or reject the connection.— Reject devices from using the service if not trusted for the serviceIf a non-trusted device attempts to access the service, the connection will be rejected automatically without informing the user.Notes: If a device is trusted for a service, it may connect to this ser-vice on your local device without informing you.
119AES AES-CCMP is the encryption method dened with IEEE 802.11i and certied with WPA2. Stronger than RC4 (which is used with both WEP and TKIP), AES-CCMP is considered sucient for FIPS 140-2. AES - Advanced Encryption Standard CCMP - Counter Mode CBC-MAC ProtocolAuthentica-tione process of verifying the identity of:• Astationattemptingtogainaccesstoanetwork.• Anetworktowhichastationistryingtogainaccess.IEEE 802.1X, which is the authentication component of WPA and WPA2, performs mutual authentication through an Extensible Authentication Protocol (EAP) type. With mutual authentication, the network authenticates the station and the station authenticates the network.Auth Type Auth Type indicates the 802.11 authentication type used when associating to an access point. SCU authentication type param-eters include:• Open-istwo-stepauthenticationtypeinvolvesthestationsending a request (usually a randomly generated key) to the access point. e access point sends an authentication response that contains a success or failure message. Once accepted, the keyisonlyusedforashortperiodoftime;thenanewkeyisgenerated and agreed upon.• Shared-With a sharedauthenticationtype, boththestationand the access point have the same “shared” key or passphrase.• LEAP(Network-EAP)Note: See http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_exam-ple09186a00801bd035.shtml for a Cisco explanation of 802.11 authentication using Open and Network-EAP. e Summit Client Utility refers to Network-EAP as LEAP.Note: Summit highly recommends the use of Open which is also the SCU default. is setting can be edited from the Prole window of SCU.Bit Rate Bitrate is the measurement of how much data is transmitted in a given amount of time from one location to another. It is generally measured in bits per second (bps), kilobits per second (Kbps), or megabits per second (Mbps).CAM CAM (Constantly Awake Mode) is a power save mode that keeps the radio powered up continuously to ensure there is minimal lag in response time. is power save setting con-sumes the most power but oers the highest throughput.CKIP CKIP (Cisco Key Integrity Protocol) and CMIC (Cisco Mes-sage Integrity Check) are Cisco-dened predecessors to WPA TKIP and are supported only on Cisco Wi-Fi infrastructure. An SCU prole setting of CKIP (not CKIP-EAP) means that the encryption keys are dened in SCU. An SCU prole set-ting of CKIP-EAP means that the encryption keys are derived dynamically from an EAP authentication.Note: If the SCU active prole has an encryption setting of CKIP or CKIP EAP, then the Summit radio associates or roams successfully to an access point that is cong-ured with the following:• eSSIDandotherRFsettingsoftheSCUactiveprole• eauthenticationmethodoftheSCUactiveprole• Anyofthefollowingencryptionsettings:– WEP only (no CKIP or CMIC)– WEP with CKIP– WEP with CMIC– WEP with CKIP and CMICNote: Summit recommends the use of TKIP or WPA2.Appendix A — EAP TypesClient Name For the SCU, the device name assigned to the Summit radio and the client device that uses it.Note: If CCX Features are set on the SCU Global settings page, then the client name is relayed and used for as-sociation.Credentials e Credentials button on the Prole window of SCU allows you to add or edit the authentication credentials for the selected EAP type. See 6.1.2.6 EAP Credentials on p. 71 fopr more information.EAP See 6.1.2.6 EAP Credentials on p. 71 for more information.Fast Fast is a power save mode that switches between PSP (Power Save Protocol) mode and CAM mode, depending on network trac. For example, it switches to CAM when it is receiving a large number of packets and switches back to PSP aer the packets have been retrieved. Fast is recommended when power consumption and throughput is a concern.Encryption Encryption involves scrambling transmitted data so that it can be read only by the intended receiver, which has the proper key to decrypt unscramble the encrypted data. In Summit Client Utility, the Encryption setting in a prole can refer not just to an encryption method but also to an authentication method and an encryption key management protocol. For more information, see “SCU Encryption Settings” Table.Maximum Maximum (Max PSP) is a power save mode where the access point buers incoming messages for the radio. e radio oc-casionally ‘wakes up’ to determine if any buered messages are waiting and then returns to sleep mode aer it requests each message. is setting conserves the most power but also provides the lowest throughput. It is recommended for radios in which power consumption is most important (such as small battery-operated devices).Power Savez Indicates the radio’s current power save setting. Power save mode allows you to set the radio to its optimum power-consumption setting.Maximizing battery life for full shi operation is an important consideration for vendors and users of hand-held data termi-nals and similar devices. Summit provides a number power save modes that can signicantly reduce the radio’s power consump-tion and maximize the battery life of the host device.Summit supports the three following power save modes:• CAM(ConstantlyAwakeMode)• Fast• MaximumWhen in power save mode, the radio “sleeps” most of the time and “wakes up” only when it has data that needs to be sent to the infrastructure (or at an interval determined between the station and the access point). When the radio is awake, the access point also delivers to the station any data that has been buered dur-ing the radio’s sleep period.Radio Mode Radio mode is an SCU Prole setting that indicates the use of 802.11a, 802.11g, 802.11b, and 802.11n frequencies and data rates when interacting with an access point, or the use of ad hoc mode to associate to a station radio instead of an access point.When SCU operates with a Summit 802.11g radio, an adminis-trator can select from among the following radio mode values:• Bratesonly-1,2,5.5,and11Mbps• Gratesonly-6,9,12,18,24,36,48,and54Mbps• BGratesfull-AllBandGrates• BGSubset-1,2,5.5,6,11,24,36,and54Mbps.isshouldonly be used with Cisco APs running IOS in autonomous mode (without controllers). For Cisco APs that are tied to controllers and for non-Cisco APs, Summit recommends BG rates full.(cont’d)
120Radio Mode(cont’d)• AdHoc-Whenselected,theSummitradiousesadhocmodeinstead of infrastructure mode. In infrastructure mode, the radio associates to an AP. In ad hoc mode, the radio associ-ates to another station radio that is in ad hoc mode and has the same SSID and, if congured, static WEP key.Note: e default is BG rates full.Note: See “802.11a/g Radio Mode with 802.11g Radio” for ad-ditional information.When SCU operates with a Summit 802.11a/g radio, an admin-istrator can select from the following radio mode values:• Bratesonly-1,2,5.5,and11Mbps• Gratesonly-6,9,12,18,24,36,48,and54Mbps• BGratesfull-AllBandGrates• Aratesonly-6,9,12,18,24,36,48,and54Mbps(sameasGrates)• ABG rates full - All A rates and all B and G rates, withArates (the 802.11a radio) preferred (see “Preferred Band for 802.11a/g Radio” for more information).• BGA rates full - All B and G rates and all A rates, with Band G rates (the .11g radio) preferred (see “Preferred Band for 802.11a/g Radio” for more information).• BGSubset-1,2,5.5,6,11,24,36,and54Mbps.isshouldonly be used with Cisco APs running IOS in autonomous mode (without controllers). For Cisco APs that are tied to controllers and for non-Cisco APs, Summit recommends BG rates full.• Adhocmodeinsteadofinfrastructuremode.Ininfrastruc-ture mode, the radio associates to an AP. In ad hoc mode, the radio associates to another station radio that is in ad hoc mode and has the same SSID and, if congured, static WEP key.Note: e default is ABG rates full.Note: See “802.11a/g Radio Mode with 802.11g Radio” for ad-ditional information.Preferred Band for 802.11a/g RadioWhen the radio mode value is ABG rates full, the 5 GHz (A) band is preferred over the 2.4 GHz (BG) band. When the radio mode value is BGA rates full, the 2.4 GHz (BG) band is preferred over the 5 GHz (A) band.• AdHoc- Whenselected,the Summitradio usesWhen try-ing to associate to an access point, the radio considers access points in the preferred band. If the radio is able to associate to one of these access points, then the radio will not try to associate to an access point in the other band. e only time that the radio attempts to associate to an access point in the non-preferred band is when the radio is not associated and cannot associate in the preferred band.When roaming, the radio considers only access points in the current band (the band in which the radio is currently associ-ated). e radio will consider an access point in the other band only if it loses association.802.11a/g Radio Mode with 802.11g RadioWhen an administrator tries to create or edit a prole, SCU de-termines which radio is operating in the device and populates the available radio mode values according to the radio type. Suppose a prole created for an 802.11a/g card is loaded on a device with an 802.11g card. If a radio mode value of A rates only, ABG rates full, or BGA rates full was set in the prole, then SCU displays a value of BG rates full. If the administrator does not save any changes to the prole, then SCU leaves the prole, including the radio mode, unchanged. If the admin-istrator saves any changes to the prole, then SCU saves the radio mode value as BG rates full.SSID Service Set Identier. Unique name of up to 32 characters that identies a particular 802.11 WLAN.e SSID is attached to the header of packets that are sent over a wireless network.Appendix A — EAP Types (cont’d.)Tx Power In SCU, Tx Power displays on the Status window to indicate of the power of the radio, in milliwatts (mW). is value can beoverwrittenbytheAP;theAPcandictatetotheclientwhatpower to use.WEP WEP (Wired Equivalent Privacy) encrypts transmitted data using 64-bit or 128-bit encryption. WEP, which was dened with the original IEEE 802.11 standards, is not recommended because a WEP key can be “broken” in less than an hour using commonly available tools.WPA/WPA2 WPA (Wi-Fi Protected Access) and WPA2 (Wi-Fi Protected Access 2) are security certications dened by the Wi-Fi Al-liance. To earn a WPA or WPA2 certication, a product must pass a set of tests that elements of the security specication have been implemented correctly. Since March 2006, WPA2 is mandatory for all new equipment that is certied by the Wi-Fi Alliance.Both WPA and WPA2 include three security elements: authen-tication, encryption, and encryption key management. WPA and WPA2 support the same authentication methods and similar key management methods. e primary dierence be-tween the two is in the area of encryption: WPA denes TKIP astheprimaryencryptionmethod;WPA2denesAES-CCMPas the primary encryption method.Both WPA and WPA2 include a Personal version and an Enter-prise version. With WPA-Personal and WPA2-Personal, which SCU refers to as WPA-PSK and WPA2-PSK, authentication is done through a pre-shared key (PSK) or passphrase that is statically congured on every client device and infrastructure device. With WPA-Enterprise and WPA2-Enterprise, authenti-cation is IEEE 802.1X, which uses an EAP type. WPA2-Enter-prise is the equivalent of IEEE 802.11i, the ratied standard for Wi-Fi security.
121Prole Setting Authentication Encryption Key ManagementNone None None NoneWEP None WEP Static (in SCU)WEP EAP EAP Type WEP Dynamic (from EAP)CKIP None WEP+CKIP+CMIC Static (in SCU)CKIP EAP EAP Type WEP+CKIP+CMIC Dynamic (from EAP)WPA-PSK PSK/password (in SCU)TKIP WPAWPA-TKIP EAP Type TKIP WPAWPA CCKM EAP Type TKIP WPA+CCKMWPA2-PSK PSK/password (in SCU)AES-CCMP WPA2WPA2 AES EAP Type AES-CCMP WPA2WPA2 CCKM EAP Type AES-CCMP WPA2+CCKMAppendix B — Encryption SettingsIn SCU, the Encryption setting in a prole can refer not just to an encryption method but also to an authentication method and an encryption key management protocol. e following table provides an explanation of SCU Encryption settings:
122Toll Free : +1 (855) DAP-TECH (327-8324)www.daptech.comCopyright © 2012, DAP TechnologiesAll rights reserved.7450 South Priest DriveTempe, Arizona, 85283 USATel: +1 (855) 327-8324Fax: +1 (480) 705-4216United States875, boul. Charest O. Bureau 200Québec (QC) Canada G1N 2C9Tel: +1 (800) 363-1993Fax: +1 (418) 681-0799Canada25 Nufeld WayAbingdon, England OX 14 1RLTel: +44 (0) 1235 462130Fax: +44 (0) 1235 462131Europe, Middle East, Africa

Navigation menu