GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual 1

GuangZhou Walkera Technology Co., Ltd 2.4GHz Transmitter DEVO 12E manual 1

Users Manual part 2 of 11

Download: GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual 1
Mirror Download [FCC.gov]GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual 1
Document ID2246007
Application IDvhhzY35Of3si6HJEbqniHA==
Document DescriptionUsers Manual part 2 of 11
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize365.92kB (4573993 bits)
Date Submitted2014-04-18 00:00:00
Date Available2014-04-18 00:00:00
Creation Date2014-04-15 15:19:30
Producing SoftwareGPL Ghostscript 8.15
Document Lastmod2014-04-15 15:19:30
Document TitleDEVO-12E manual 1.pdf
Document CreatorPScript5.dll Version 5.2.2
Document Author: Frank

(leUenlion
DEVC) ‘l EE
Welcome to use the DEVO 12E transmitter
8.1 Right-hand throttle switched to left-hand throttle
(1) Mechanical switch
Remove the battery and 6 fixed screws in the back cover of Transmitter, and remove the transmitter back
cover (Be careful not to break the Wires).The internal conditions of the left and right throttle are showed in
the followmg pictures. Then use a Phillips screwdriver to release the connecting rod fixed screw\screw F\screw
G and throttle arresting slices in the right throttle poSition.and fix them up in the corresponding left hand Throttle
positionAccording to personal feeling to adjust screw F(adjust the Throttle stick to desired tention).then fixed
up the transmitter back cover.
Linkage Fixed Screw screw F screw G Linkage Fixed Screw
nght throttle set Left throttle set
(2) The ELECTRONIC switch
In the main interface, press ENT to access the main menu,Press UP\DN to choose “system menu"; Press
UP\DN to choose “stick model" and access via “ENT” key, or to choose “model 2W and confirm Via ENT key,
make a mark 2/" before the choosed modelPress EXT to exit after setup complete.
Stick Mode
Model 1
, ,
Model3 @EQ)
Stick Mode
Model ‘l
Model 2
Model 3
3.2 Left-hand throttle switched to right-hand throttle
Through the mechnical and
electronic swith.tne right
hand throttle swuch to the
left hand successfully and
can be used normally.
Model 4
(1) Mechanical switch
Refer to the above “Mechanical SWitch" to open the transmitter cover.
See the following pictures to learn the internal conditions of the left and right hand stich. Then use a Phillips
screwdriver to release the connecting rod fixed screw\screw F\screw G and throttle arresting slices in the
left hand throttle position,and fix them up in the corresponding right hand Throttle position.According to personal
feeling to adyust screw F(adjust the Throttle stick to desired tention).then fixed up the transmitter back cover.
Linkage Fixed Screw screw F screw G Linkage Fixed Screw
Throttle Control Spring
screw G screw F
Right throttle set Left throttle set
DEVD 1 EE 77
deUethion
DEVU 1 2E Welcome to use the DEVO 12E transmitter
(2) The data switch
Refer to the steps of “8.1 right hand throttle switch to the left hand, (2)electric switch",access to “stick model".
The left hand throttle switch to the right hand.There are 4 stick models can be choosed at the stick position.
Press UP\DN to choose
, Stick Mode 5 | i ll Stick Mode E l I ll
‘model 1\3" and confirm Via
ENT key,make a mark “t/" JMode 1 Model 1
before the choosed mode. Model 2
Press EXT to exit after setup Model 2 /~\ /,\ * /'*\
complete.The data can be Model 3 14w 14M 4M°del 3 a} i Ri
\E/ \J/ \j/ \1/
sWitched automatically. Model 4 Model 4
The SWitch from left hand throttle to right is completed and your DEVO 12E is ready for normal flying.
Note: Pay attention to the strength when removing and adjusting the screws Excessive strength may damage
them.
9.0 Training funct
Two DEVO 12E transmitters working together can execute the training function to meet the requirements for
the beginner. The setting method is shown as below:
(1) Data copy
First, use the wireless copy function between two DEVO 12E to copy the main transmitter's model data to
the trainees transmitter, this promise the model data between two transmitters is same. Refer the copy method
to the second part of helicopter "2.4 model Wireless copy" and do the following steps:
(2) Linkage Linkage icon at trainee's DEVO12Ei
Insert the digital signal wire from the trainer's transmitter into the
DSC socket of the trainees transmitter. Turn on the transmitter and A U i
. . . e en IOn
a linkage icon Will be shown on the boot screen. “a,“
I I 00:00 %x
7 7 . 0.0%
osc socket psc socket
W 9 ,. 9
Digital signal wire Digital signal wire
linkage icon
Turn on the power of the trainer's radio. Find out the trainees model data, and then let the trainer's Radio bind
With the aircraft model and fly it normally. Then turn off the powerinsert the other end of the digital Signal
wire into the trainer's DEVO 12E, and then turn on its power. A linkage icon will be shown as below:
Train92 is air and trainer is working Trainee is working and trainer is air
i l Trainer icon
Je ention E W- ole ention fi' V ”mm Training status display: when the trainer's
2.55m Model 1 2.46M: Model 1 icon becomes into “"X, the trainee stops
flying and the trainer is Working; when the
00:00 00:00
00% § 0.0% %x trainers icon turns into «/ , the trainee is
flying and the trainer is in leisure.
Left Trim
tli'
Right Trim
(3) Usage method
The training switch can be freely switchable between Left trim
and Right trim. The default setting is Right trim. See the right
illustration: 0 I
DEVO 1EE78
cJeUention
DEVD ’I BE
Welcome to use the DEVO 12E transmitter
During flight, if the trainer pushes Right Trim once, the linkage icon WI” be shown as "\/" that means the
control right is moved to the trainee from Trainer. If trainer pushes Right Trim once again, the linkage icon
will be shown as “X" that means the trainer takes back the control right from the trainee.
(4) Setting for training function channels
Trainee is available to get full or part of flight control power to the aircraft model via setting the training function
channel in the trainers radio. Below is the setting method:
Trainer oIIII
Press the ENT to enter Main Menu. and then press UP or DN to move —
the navigational mark to select Function Menu. Then press ENT to Switch I
enterthe Function Menu and press UP or DN to select “Trainef' ,then
press ENT to enter the Trainer interface. The available channels are
shown below. and the current status of trainer switch is also shown Elevator Inhibit
there.
Trainer switch selection:Press UP or DN to select the switch option; press R or L to select the switch which
you want. It includes right and left trim.The default setting is Right trim.
Channel selection:Press UP or DN to select the channel option; Press R or L to select the channel(s) which
you want to grant to trainee. The channel(s) you have selected will be activated as “Active". The channels
which are not granted to trainee will be kept inhibited. The default setting is “Inhibit".
Press EXT to exit.
10.0 C stomized fixed ID
This setting will bind DEVO 12E with its receiver in a unique corresponding relationship. It will greatly speed
up the time of automatic binding when DEVO 12E powered on.
(1) Setting for fixed ID
The setting for fixed ID should be under the status that automatic ID binding is successfully finished. Below
is the setting method
Press ENT to enter the main Menu and press UP or DN to move the navigational mark to select Model menu.
Press ENT to enter Model Menu. Press UP or DN to select Fixed ID and press ENT to enter the Fixed ID
setting interface.
If you want to activate the fixed F'Xed D E ' l H F'Xed ID D l l H
ID settings, press R or L to Status Status
change the status from off to n “
ON. A series of random digits
will be shown below after ID Code
change to On. 325185
Press UP or UN to choose the ID code setting, press R or L to choose
the digits,press UP or DN to move to the next code setting . there
are 6 digits can be setted.
Press ENT key after the new ID has been setted An inquiry interface of “Are you sure?" pop up. “ID Code
Matching Will be shown
after press ENT. After
matching, the interface will
be returned to Model Menu.
Fixed ID [IIII Fixed ID EIIII
Fixed ID
ID Match- - - -
Are you sure?
DEVC] 12E79
oleUention
DEVD 1 2E Welcome to use the DEVO 12E transmitter
(2) Fixed ID cancellation
Insert the assorted BIND PLUG into the output terminal of BATT before the receiver is powered on. and then
plug 5V DC power into other output terminal. The red light of receiver will tlash slowly. This means the fixed
ID code has been cancelled. Pull out bind plugDEVO 12E also needs to make relative cancellation and
reVision after the fixed ID in receiver is cleared out.
In the main interface press the ENT to enter Model Menu and then A
press UP or DN to move the navigational mark to select Model Menu. F‘
Press ENT to enter ModeL Menu. Press UP or DN to select Fixed
ID code and press ENT to enter the Fixed ID code interfacePress
UP or UN to select Status option. Press R or L to change the status \- i
to Off. Then press EXT to exit.
11.0 Installation ment for receiver
qui
(1) It is important to correctly mount your radio system in your model. Below are some advices on how to
install your equipments.
(2) Wrap the receiver with 10mm thickness polyfoam and fix it With a rubber band or magic string on your
helicopter or airplane. It helps protect the receiver.
(3) It is necessary for you to use rubber grommets and copper sleeves to isolate the vibration from the main
body. The mounting screws cannot be overrtightened. Othervvise. the rubber grommets will be distorted
and decrease the vibration absorption effect.
(4) When mounting the servos, make sure the servos’ bell cranks can move freely over their whole travel
range and ensure the control linkages don't touch or impede the movement of the servos.
(5) If installing various switches,please keep them far away from the engine tuned pipe and high vibration
sources. Ensure all the switches move freely over theirwhole range.
(6) Don't make the receiver antennas wrapped or parallel,keep the two antennas form 90 degrees angle.
I'— Il/wl/
11.1 Receiver Frame rate setting
There are 11Millisecond and 22 Millisecond Frame Rate. When using 11 Millisecond frame rate, it can't be
compatible with Analog servos. Please select the 22 Millisecond Frame Rate if use Anolog servos.
(1) LED indicator
I Red LED indicates 22ms frame rate:
I Blue LED indicates 11ms frame rate;
I Red&Blue LED indicate the frame rate is under setting;
I Red& Blue LED flash means both frame rate can be set;
DEVD ’lEEi’lU
deUethion
Welcome to use the DEVO 12E transmitter
DEVO 1 2E
(2) Setting method ‘ Frequency Status
After TX and RX binding. press the switch with the tool indicator
pen or screwdriver. both indicators will turn on. About 5 l '—{i
seconds, both indicator will flash, then release the sztch ‘
and press it once again, the frame rate can be changed ,
and the indicators will turn red or blue only. Red means ‘
22ms frame rate and Blue means 11ms. ‘
Switch buttoni
12.0 Installation requ ment f0 DEVO 2E battery pa
Open the battery cover of DEVO 12E transmitter and take out the battery box. Then put 8 cells AA battery
or the same size full charged NIMH battery into the battery box. Please check again to make sure the polarities
are correct.
Warning: Do not put the polarities of batteries in the opposite directions.
When insert the battery box connector to the transmitter connector, please make the fool proof is right. showmg
as below plcture.Then put the battery box back to battery case.
Anode of the battery Cathode of the battery
Battery box fool-
proof plug
‘ Power fool-
proof plug
Cathode of the battery Anode of the battery
Note:lt you don‘t use the transmitter, please take out the battery.
12.1 DEVO 12E Battery Charging
Warning: the CHG socket is only used for the rechargeable NIMH batteries. If using the batteries which is
unchargeable. The CHG socket is not allowed to use.
.7 CHG Charge socket: input DC at
12V. 50mA: PolarityQ—yiQ
l O
‘_ r
DEVD 12E711
AeUen ion
DEVCJ ’I BE
Part two
Helicopter
All the functional settings, which are relative
to the operation system of DEVO 12E itself,
are fully integrated in System Menu. They
include Language, Display, Buzzer, vibrator,
Stick Mode, Stick Direction, Stick
calibration, Battery and About.
oleUenlion
DEVC} ‘l EE
Welcome to use the DEVO 12E transmitter
.0 System nu
All the functional settings, which are relative to the operation system of DEVO 12E itself, are fully integrated
in System Menu. They include Language, Display, Buzzer, vibrator, Stick Mode, Stick Direction,Stick calibration,
Battery and About
Below is the boot screen of helicopter:
Throttle trim
Transmission power display
Elevator trim
Battery volume
(J U {- display
e en IOl’l
Model name
Timer display
Model type
Throttle percentage display
Value
Rudder trim display gilerlon trim
isp ay
1.1 Language setting
Press ENT to the Main Menu, press UP or DN to select System Menu, then press ENT to System Menu.
Press UP or DN to select "Language" and press ENT to the Language L
setting interface. Press UP or DN to select the language that you anguage
want. A "V" will be shown on the screen after selected. Press EXT JEng sh
to exit.
i‘r'WA'l 'Y
Deutsch
Frangais
1.2 Display
Press ENT to the Main Menu, press UP or DN to select System Menu. then press ENT to System Menu.
Press UP or UN to select "Display" and press ENT to the Display setting interlace.
Display llll Three items are available to be set. Below are the setting methods
for them:
Contrast
(1) Backlight contrast: the backlight contrast is adjustable by pushing
UP or DN to move the navigational mark to the digits after Contrast.
Press R key to increase the backlight contrast. while press L to
5/10 decrease it.
Lightness
(2) Backlight lightness: the backlight lightness is adiustable by pressing UP or DN to move the naVigational
mark the digits after LightnessThe power consumption will be increased if the backlight lightness is too
bright and the battery cruise duration will be shortenedPress R or L to increase or decrease the lightness.
When the value is one means turn off the backlight.
(3) Backlight time out: it is possible to set the duration which LCD stays at highlight in the form of “Always on"
or any period from 5 to 60 seconds with an interval of 5 secondsPress UP or DN to move the navigational
mark to select the digits after Timeout. Press L to short the time of backlight duration or keep it in the
form of "Always on" while push R or prolong the time. The maxium is 605.
Press EXT to exit.
DEVO 12E7’la
OleUention
DEVO 1 EE
Welcome to use the DEVO 12E transmitter
1.3 Buzzer warning
Press ENT to the Main Menu, press UP or DN to select System Menu. then press ENT to System Menu.
Press UP or UN to select "Buzzel" and press ENT to the Buzzer setting interface.
Buzzer u i I H
Status (1) Status:There are On and off two status on the Buzzer interface.
Pressing UP or DN to move the navigational mark to the status
“ option. Pressing R or L to change the ON or OFF status. lt includes
Throttle Stick Throttle stick,knobs and Tones items under the status is ON.
lnhibit
(2) Throttle stick buzzer: Press UP or DN to move the naVigational mark to Thro Stick item then press R or L
to change the status from lnhibit to Active. When Buzzer is at the status of On, if Throttle Stick is set as
“Active", a relative musical scale will make response when moving the throttle stick. You can iudge the
position of the throttle stick according to the different musical scales. Also, it can be set as Inhibit.
(3) Knobs midpoint Buzzer: When Buzzer is at the status of On. it Knobs is set as “Active“,there is buzzer
sound when you turn the AUXA and AUX5 to the midpoint. If you don't need the buzzer sound. please
change the status to inhibit.
(4) Buzzer tone: the tone is composed of 10 grades. You can choose the favorite one according to your
interests.Press UP or DN to move the naVigational mark to Tone item and press R or L to make a listening
test. Press EXT to exit.
1.4 Vibrator
The vibrator used as an alarm function to remind the users.
Press ENT to get the Main Menu, press UP or DN to select System Menu. And then press ENT to get System
Menu, press UP or DN to
select Vibrator. Press ENT to
get Vibrator setting interface. Status Status
There are two status as Inhibit
and Active. Press R or L to m m
select Active it need. Press
EXT to exit after finished.
Vibrator E i i ii Vibrator : I i ii
1.5 Stick Mode
Press ENT to get Main Menu, press UP or DN to select System Menu, and then press ENT to the System
Menu, press UP or DN to select Stick Mode. and press ENT to get stick Mode setting interface.
Stick Mode Stick Mode l:l|ll|
M°de' 1 MODE 2 and MODE 4 are Mme' 1
JMode 2 listed in left-hand throttle. Model 2
Model 3 Model 3
Model 4 \ ‘ 4 Model 4
Stick Mode Stick Mode Iiil
Mode”
4 ° ° MODE 1 and MODE3 are Modem
Model 2 .7 .7 listed in right-hand throttle. .7
Model 3 at} Qt) JMOdel 3 ,4) :4},
Model 4 \E/ \T/ Model 4 \E/ \T/
Select the stick mode according to the throttle mode showing on the screen. DEVO 12E offers 4 stick modes,
please refer to “8.0 Switches exchange between left-hand and right-hand throttles. Press EXT to exit after finished.
DEVD ’lEEi’l4
oleUethion
Welcome to use the DEVO 12E transmitter
DEVD ’l EE
1.6 Stick Direction
Press ENT to get Main Menu, press UP or DN to select System Menu,
Stick Direction : l i ll
and then press ENT to the System Menu. press UP or UN to select
Stick Direction, and press ENT to get stick direction setting interface. Elevator I
Stick Direction:There are four items available as Elevator, Aileron, m
Throttle and Rudder. Press UP or UN to select the stick which will Aileron
change direction, and press R or L to change the direction. The factory
setting is Normal.
1.7 Stick Calibration
It is a function to re-calibration when stick unusual.
Calibration method:
Press “ENT" to the Main Menu, press UP or DN to select System Menu, then press ENT to System Menu.
Press UP or UN to select Stick
Calibration and press ENT to
the Stick Calibration setting
interfacePress ENT to enter
Calibration,and see the left
illustration:
Stick Calibration
E o Calibrate
Stick Calibration
ENT to Flnsh
Stick Calibration
Clockwise or counter clockwise mechanically move the right stick and
left stick from minimum levels to maximum levels several times, and
then return the stick to the neutral positions, respectivelylt will shows
the calibration is successful after you press ENT to confirm
ENT to Calibrate
Calibration Success!
1.8 Battery
Battery voltage can set up the warning value for radio battery in
lower voltage.
Press ENT to the Main Menu, press UP or UN to select System Menu,
then press ENT to System Menu. Press UP or DN to select "Battery"
and press ENT to the Battery setting interface. Warning voltage value
can be changeable by R or L button.
1.9 About
Press “ENT" to the Main Menu. press UP or UN to select System
Menu, then press ENT to System Menu. Press UP or UN to select
About and press ENT to the About setting interface.
Press EXT to exit after finished.
Press EXT to exit after finished.
Battery
Alarm Voltage
About u i i i I
Software
Ver. 1.0A
Library
Ver. 1.0
Model Menu
Model Menu manages all the model data saved in DEVO 12E. It includes Model Select, Model Name, Model
Copy, Model Transmit, Model Receive, Model Reset, Type Select, Trim System, Stick Position Switch, Device
Select, Device Output, Swash Type, Power Amplifier, Fixed ID and Sensor setting.
DEVD 1EE715
CleUethiori
DEVD ’I 2E
2.1 Model Select
Press ENT to enter Main Menu and press UP or DN to make Model
Menu is selected. Press ENT to get lhe Model Menu and press UP
or DN to select Model select, press ENT to enter the Model Select
setting interface.
Press UP or DN to select the model you desired, press ENT to confirm
and marks'K/"in the front of selected one. Total 30 models are optional.
Press EXT to exit aftert’inished.
2.2 Model Name
Welcome to use the DEVO 12E transmitter
Model Select u i I II
«1 ~§ Model 1 I
2 >—§ Model 2
3 ’-§ Model 3
4 Ӥ Model 4
In the menu of model name, you can make a desired name for your model for long term storage lts data
can be directly Withdrawn in next flightsRepeat the step “2.1 Model Select" to choose the model you want to
name or save, press EXT to back to the interface.
Press “ENT" to enter Main Menu, press UP or UN to select “MODEL
Menu", then Press “ENT" to enter Model Menu; Press UP or DN to
select “Model NAME" and then press “ENT“ button to enter the "Model
Name" setting interface
Press UP or DN to select the character and figure which are needed
to be changed, press R or L button to change the character and figure,
and press UP or UN to set next one. Press EXT to exit afterfinished.
2.3 Model Copy
Model Name
No. ‘I
Name
Model
Press ENT to enter "Main Menu" and press UP or DN to make "Model Menu" is selected. Press ENT to enter
"Model Menu" and press UP or DN to select" Model Copy", press EN
T to the "Model Copy" setting interface.
Model Copy [liii Model Copy [iiii
Source I Source: 1Model 1
~/1 Model 1 Des!
, x/‘l -—§ Model ‘I
2 *9, Model 2
3 ~§ Model 3 2 '5 Mm“ 2
model you want to be copied
as source model and press
ENT to confirm, The serial No.
and model name of Source
Model will be shown as left
Illustration.
Press UP or DN to choose the
Then press UP or DN to locate the source model, press ENT to confirm.
Then an enquire “Are you sure?" is popped up as below Illustration.
Press ENT to copy, or press EXT to exit
2.4 Model wireless copy
Model Copy
Source: 1Model 1
Best: 2 Model 2
The model data between two DEVO 12E equipments can be wirelessly copied via Model Transmit and Model
Receive in Model Menu.
(‘I) Model transmission
Press ENT Io enter "Main Menu" and press UP or DN to select "Model Menu". Press ENT to enter "Model
Menu" and press UP or DN to select "Model transmission", continue
setting interface.
to press ENT to enter "Model Transmit"
Model Transmit
Model Transmit Iiii
«1 -—§ Model 1 I
2 H} Model 2
3 “3 Model 3
4 “‘3 Model 4
Model 1
Are you sure?
iiii Press UP or DN to choose the
source model which will be
transmitted, and press ENT to
confirm, an enquiry information
“Are you sure?" Will be shown
as left Illustration.
DEVD ’IEEi’IB

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 10
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2014:04:15 15:19:30
Modify Date                     : 2014:04:15 15:19:30
Title                           : DEVO-12E manual 1.pdf
Creator                         : PScript5.dll Version 5.2.2
Author                          : Frank
EXIF Metadata provided by EXIF.tools
FCC ID Filing: S29DEVO12E

Navigation menu