GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual 1
GuangZhou Walkera Technology Co., Ltd 2.4GHz Transmitter DEVO 12E manual 1
Contents
- 1. Users Manual part 1 of 11
- 2. Users Manual part 2 of 11
- 3. Users Manual part 3 of 11
- 4. Users Manual part 4 of 11
- 5. Users Manual part 5 of 11
- 6. Users Manual part 6 of 11
- 7. Users Manual part 7 of 11
- 8. Users Manual part 8 of 11
- 9. Users Manual part 9 of 11
- 10. Users Manual part 10 of 11
- 11. Users Manual part 11 of 11
Users Manual part 6 of 11
cieUeniion DEVD 1 2E Welcome to use the DEVO 12E transmitter Press UP or DN to select Elevator on the Fail Safe interface, then press R or L to change the status of Servo Hold into Fail Safetlf you want to Keep Servo hold status, there is no need to reset). There is a expanded sub-item blow. Press UP or DN to select 0%, then press R or L to increase or decrease, respectively, the position amount which centers on the neutral point of servo. The available value is 125%, respectively. 0% is the neutral point of servo. Fail Safe [Hit The setting methods for other channels are same as above. Elevator I Press EXT to exit after finished. Fail Safe Note: checking whether all the actions when fail safe happened are correct, is a must after the setting is finished. It is dangerous to use full throttle, especially after fail safe taken place. 3.17 Sensor View Setting method:Press ENT to enter the Main Menu and press UP or DN to move the navigational mark to select Function Menu.Then press ENT to enter the Function Menu and press UP or DN to select Sensor View, then press ENT to enter the Sensor View interface, like below pictures. If all the sensors disconnect, telemetry signal lost, there Will be inhibits shown on the view. If all work normal, all the measured data will be shown. (1) Voltage:Show 3 diffferent measured voltage value; Voltage :llll Voltage :Illl Inhibit I 5.3 Unit I Inhibit 8.3 Unit Inhibit 0.0 Unit (2) Temperature: Show 4 different measured temperature value; Temperature 5 i i ii Temperature 5 i i ii Inhibit 78'C Inhibit I r7'c I Inhibit *9'C Inhibit *7‘C (3) Rate Sensor:Show 2 different measured RPM value; Rate Sensor iiii Rate Sensor Inhibit 5000RPM Inhibit I 4000RPM I (4) GPS Sensor:Press UP or DN to turn to GPS function, show located date, time, longitude, latitude, altitude and speed; GPS Sensor :iiii GPS Sensor :iiii Inhibit East 113“ 23.7120 Inhibit North 22“ 53.4805 Inhibit -3.7 m inhibit I 0.0 km/h I DEVO 1 BE 7 37 JeUethion DEVD 12E Welcome to use the DEVO 12E transmitter 3.18 Trainer Two DEVO 12E transmitters working together can execute the training function to meet the requirements for the beginner. The setting method is shown as below: (1) Data copy First, use the wireless copy function between two DEVO 12E to copy the main transmitter’s model data to the trainees transmitter, this promise the model data between two transmitters is same. Refer the copy method to the second part of helicopter "2.4 model Wireless copy" and do the following steps: (2) Linkage Linkage icon at trainee's DEVO tZEi Insert the signal wire from the trainer's transmitter into the DSC socket of the trainees transmitter Turn on the transmitter and a JeUenlion linkage icon will be shown on the boot screen. 2.46m ' ' 00:00 @X 0.0% Dsc socket . Dsc socket . . . —_— ___ Digltal signal Wire Digital Slgrlal Wire linkage icon Turn on the power of the trainer's radio. Find out the trainees model data, and then let the trainer‘s Radio bind with the aircraft model and fly it normally. Then turn off the power.lnsert the other end ofthe digital signal wire into the trainer’s DEVO 12E, and then turn on its power. A linkage icon will be shown as below: Trainee is or and iramer is working Trainer: is working and tralricr is off i l Trainer icon Je ention E' X ““‘WH‘ Je ention 3' V “““H‘” Training status display: when the trainer‘s 2 mm Model 1 2.:st Model 1 icon becomes into “fix the trainee stops 00:00 %X 00:00 @it flying and the trainer is working; when the trainer's icon turns into"«/" the trainee is o u i 0'0 /” 0'0 A flying and the trainer is in leisure. (3) Usage method Left Trim ; Right Trim The training switch can be freely SWitchable between Left " ' trim and Right trim. The default setting is Right trim. See 3. I i n i l ”I the right illustration: During flight, if the trainer pushes Right Trim once. the linkage . 0 icon will be shown as "t/" that means the control right is moved - ‘ to the trainee from Trainer. lf trainer pushes Right Trim onceagain, the linkage icon will be shown as “X" that means the trainer takes back the control right from the trainee. (4) Setting for training function channels Trainee is available to get full or part of flight control power to the aircraft model via setting the training function channel in the trainers radio. Below is the setting method: Trainer Press the ENT to enter Main Menu, and then press UP or DN to move the navigational mark to select Function Menu. Then press ENT to Switch enter the Function Menu and press UP or DN to select “Trainer" ,then press ENT to enter the Trainer interface. The available channels are shown below, and the current status of trainer switch is also shown there. Elevator Trainer switch selection:Press UP or DN to select the switch option; press R or L to select the sWitch which you want. It includes right and left trim.The default setting is Right trim. DEVCJ 1 EE 7 SE oleUention Welcome to use the DEVO 12E transmitter DEVO 1 EE Channel selection:Press UP or DN to select the channel option: Press R or L to select the channelts) which you want to grant to trainee. The channel(s) you have selected Will be activated as “Active". The channels which are not granted to trainee will be kept inhibited. The default setting is “Inhibit“. Press EXT to exit. 3.19 Timer There are two timers which can be set as stopwatch and countdown. respectively. Each timer can be operated by sWitch or by shortcut. Setting method: Press ENT to enter Main Menu, and then press UP or DN to move the navigational mark to select Function Menu. Then press ENT to enter the Function Menu and press UP or DN to select "Timer". then press ENT to enter Timer interface. The timing range of stopwatch is from 0 to 59:59 (59 minutes 59 seconds).The default setting is stopwatch. (1) Countdown setting If you need countdown time mariner. press R or L to select the countdown.There is an expand subemenu set time item.Press UP or UN to move the navigational mark to select the option of Seting time item. Press R or L to set the countdown time. The settable countdown time range is from 00:05 to 59:55. (2) Switch selection Press UP or DN to move the navigational mark to Switch.There are inhibit and available switch options. available switch can be selected by press L or R. It includes FMOD1.2. FMODZ. MIX1.2. MIX2. ELEV D/R.A|LE DIR. RUDD D/R. GEAR SW. SPSO SW. SPSl SW. SPSZ SW and SPSB SW. We can select the desired item except these items of SPSO SW. SPS1 SW. SPSZ. and SPS3 which should be preViously set at Stick Position Switch at Model Menu(refer to “2.8 Stick Position Switch"). Press EXT to exit after finished. (3) Usage of timer Press UP or BM in main panela. it's possible to start Timers by ereflg) pressing UP key for onetime. and to pause it by pressing it the second time. Press DN to clear timer. it's ok to control time by Switch when time setting is finished on switch. Timer will be shown in main interefaoe. as right illustration: DEVD ’l 2E 738 (JeUen ion DEVCJ ’| EE Part three Airplane All the functional settings, which are relative to the operation system of DEVO 12E itself, are fully integrated in System Menu. They include Language, Display, Buzzer, vibrator, Stick Mode, Stick Direction, Stick calibration, Battery, and About. Welcome to use the DEVO 12E transmitter JeUeniiOn DEVCJ 1 EE 0 Syste Menu All the functional settings, which are relative to the operation system oi DEVO 12E itself, are tully integrated in System Menu. They include Language, Display. Buzzer, Vibrator, Stick Mode, Stick Direction,Stick calibration, Battery, and About Below is the boot screen of Airplane: Elevalurtrlm Throttle trim Transmission power display Battery volume A U J[- display e en ion 2 .46 Hz Model name Timer display 0 0 . 0 0 Model type Throttle percentage 0 . 0 0/0 display value Rudder min display Aileron trim display 1.1 Language setting Press ENT to the Main Menu, press UP or DN to select System Menu, then press ENT to System Menu. Press UP or DN to select ”Language" and press ENT to the Language setting interface. Press UP or DN to select the language that you Language— want. A "\/"' will be shown on the screen after selected. Press EXT to exit. , fiiizli‘l‘ )L Deutsch Francais 1.2 Display Press ENT to the Main Menu. press UP or DN to select System Menu, then press ENT to System Menu. Press UP or DN to select "Display" and press ENT to the Display setting interface. DlSPIaY Ellll Three items are available to be set. Below are the setting methods for them: Contrast 5, (1) Backlight contrast: the backlight contrast is adjustable by pushing _ UP or DN to move the navigational mark to the digits after Contrast. Lightness Press R key to increase the backlight contrast, while press L to 5/10 decrease it. (2) Backllght lightness: the backlight lightness is adjustable by pressing UP or DN to move the naVIgatlonal mark the digits after Lightness.The power consumption Will be increased if the backlight lightness is too bright and the battery cruise duration Will be shortenedPress R or L to increase ordecrease the lightness. When the value is one means turn off the backlight. (3) Backlight time out: it is possible to set the duration which LCD stays at highlight in the form of “Always on" or any period from 5 to 60 seconds With an interval of 5 secondsPress UP or DN to move the navigational mark to select the digits after Timeout. Press L to short the time of backlight duration or keep it in the form of “Always on" while push R or prolong the time. The rnaxium is 60s. Press EXT to exit. DEVC} 1 EE 74’l AeUethiorl DEVD 4 2E Welcome to use the DEVO 12E transmitter 1.3 Buzzer warning Press ENT to the Main Menu. press UP or DN to select System Menu, then press ENT to System Menu. Press UP or DN to select "Buzzer" and press ENT to the Buzzer setting interface. Buzzer [rill Status (1) Status:There are On and off two status on the Buzzer interface Pressing UP or UN to move the navigational mark to the status “ option Pressing R or L to change the ON or OFF status It includes Throttle Stick Throttle stick,knobs and Tones items under the status is ON. Inhibit (2) Throttle stick buzzer: Press UP 0r UN to move the navigational mark to Thro Stick item then press R or l. to change the status from inhibit to Active.When Buzzer is at the status of On, if Throttle Stick is set as “Active", a relative musical scale will make response when moving the throttle stick. You can judge the position of the throttle stick according to the different musical scales. Also, it can be set as Inhibit. (3) Knobs midpoint Buzzer: When Buzzer is at the status of On, if Knobs is set as "Active",there is buzzer sound when you turn the AUX4 and AUX5 to the midpoint. If you don't need the buzzer sound, please change the status to Inhibit. (4) Buzzer tone: the tone is composed of 10 grades. You can choose the favorite one according to your interests.Press UP or DN to move the navigational mark to Tone item and press R or l. to make a listening test. Press EXT to exit. 1.4 Vibrator The vibrator used as an alarm function to remind the users. Press ENT to the Main Menu, press UP or DN to select System Menu. And then press ENT to System Menu, press UP or DN to select Vlbrator.Press ENT to get Vibrator setting interface. Status Status There are two status as Inhibit and Active. Press R or L to m m select Active if need. Press EXT to exit after finished. Vibrator Elm Vibrator l:llll| 1.5 Stick Mode Press ENT to Main Menu, press UP or DN to select System Menu, and then press ENT to the System Menu, press UP or DN to select Stick Mode, and press ENT to stick Mode setting interface. Stick Mode E i i ii Stick Mode u i i ii M°de'1 MODE 2 and MODE 4 are “Awe” listed in leftrhand throttle. Model 2 Model 3 K E (\AJ Model 3 am in Model 4 \J \g/ J Model 4 \,/ kg/ Stick Mode E l i ll Stick Mode a l l l I MM“ MODE 1 and MODE3 are Modem Model 2 .e ., listed in right-hand throttle. 7, , Model 3 Cf £3 mm. 3 fig 53 Rl A A i Model 4 \g/ \1/ Model 4 \g/ \ Select the stick mode according to the throttle mode showing on the screen. DEVO 12E offers 4 stick modes, please refer to "8.0 SWltches exchange between left-hand and right-hand throttles. Press EXT to exit aflerfinished. DEVD 1 EE 7 42 Welcome to use the DEVO 12E transmitter (JeUention 1.6 Stick Direction Press ENT to get Main Menu, press UP or DN to select System Menu, and then press ENT to the System Menu, press UP or DN to select Stick Direction, and press ENT to get stick direction setting interface. Stick Direction:There are four items available as Elevator. Aileron. Throttle and Rudder. Press UP or DN to select the stick which will change direction, and press R or L to change the direction. The factory setting is Normal. 1.7 Stick Calibration It is a function to recalibration when stick unusual. Calibration method: DEVO 1 2E Stick Direction ii i I Elevator Normal Aileron Press “ENT" to the Main Menu, press UP or DN to select System Menu, then press ENT to System Menu. Press UP or UN to select Stick Calibration and press ENT to Stick Calibration Stick Calibration u l l l I the Stick Calibration setting interfacePress ENT to enter Calibration.and see the left illustration: ENT to ' Stick Calibration Clockwise or counter clockwise mechanically move the right stick and left stick from minimum levels to maximum levels several times, and then return the stick to the neutral positions, respectively." will shows the calibration is successful after you press ENT to confirm. ENT to Calibrate Calibration Success! Press EXT to exit after finished. 1.8 Battery Battery voltage can set up the warning value for radio battery in lower voltage. Battery Alarm Voltage Press ENT to the Main Menu, press UP or DN to select System Menu, then press ENT to System Menu. Press UP or DN to select "Battery" and press ENT to the Battery setting interface. Warning voltage value can be changeable by R or L button. 1.9 About About niiii Press “ENT" to the Main Menu, press UP or UN to select System Software Menu, then press ENT to System Menu. Press UP or DN to select V 1 0A About and press ENT to the About setting interface. er. ' Press EXT to exit after finished. Library Ver. 1.0 2.0 Model Menu Model Menu manages all the model data saved in DEVO 12E. It includes Model Select, Model Name, Model Copy. Model Transmit, Model Receive, Model Reset. Type Select. Trim System. Stick Position Switch. Device Select. Device Output, Wing Type, Power Amplifier. Fixed ID and Sensor setting. DEVD ’l EE 7 43 cJeUethiorl DEVD 1 2E Welcome to use the DEVO 12E transmitter 2.1 Model Select Press ENT to enter Main Menu and press UP or DN to make Model Model Select Ellll Menu ls selected. Press ENT to get the Model Menu and press UP or DN to select Model select, press ENT to enter the Model Select —| settlng lnterface. 2 ._§ Model 2 Press UP or DN to select the model you desired, press ENT to confirm 3 '-§ Model 3 and marks'R/‘ln the front ofselected one. Total 30 models are optional. 4 ._§ Model 4 Press EXT to exit after finished. 2.2 Model Name In the menu of model name, you can make a deslred name for your model for long term storage. Its data can be directly withdrawn ln next fllghtsRepeat the step “2.1 Model Select" to choose the model you want to name or save, press EXT to back to the interface. Press “ENT" to enter Main Menu. press UP or DN to select “MODEL Model Name Ellll Menu“. then Press “ENT" to enter Model Menu; Press UP or DN to select "Model NAME" and then press “ENT" button to enter the "Model No. 1 Name" setting interface. N ame Press UP or DN to select the character and figure which are needed to be changed, press R or L button to change the character and figure, me d e | 1 and press UP or DN to set next one. Press EXT to exlt after finished. 2.3 Model Copy Press ENT to enter "Main Menu" and press UP or UN to make "Model Menu" ls selected. Press ENT to enter "Model Menu" and press UF' or DN to select" Model Copy", press ENT to the "Model Copy" setting interface. Model Copy Press UP or DN to choose the I model you want to be copied Model Copy ll l l Source I Source: 1 Model 1 as source model and press «1 r} Model 1 0551 ENT to confirm, The serial No. ¢1 5)- Model 1 and model name of Source 2 h? Model 2 Model Will be shown as left 3 ho Model 3 2 "§ M°d°' 2 lllustratlon. Model Copy Then press UP or DN to locate the source model, press ENT to confirm. Then an enquire “Are you sure?" is popped up as below lllustratlon. Press ENT to copy, or press EXT to exit. Source: 1Model 1 Best: 2 Model 2 2.4 Model wireless copy The model data between two DEVO 12E equipments can be wirelessly copied Vla Model Transmit and Model Receive in Model Menu. (1) Model transmlssion Press ENT to enter "Main Menu" and press UP or DN to select "Model Menu". Press ENT to get ”Model Menu" and press UP or DN to select "Model transmission", continue to press ENT to enter "Model Transmit" settlng interface. Model Transmit : l l ll Model Transmit u l I ll Press UP or DN to choose the source model whlch will be transmitted, and press ENT to 2 kg Model 2 Model 1 confirm, an enquiry information 3 ’—§ Model 3 Are you sure? "Are you sure?" will be shown 4 ,_§ Model 4 as lefl lllustratlon. DEVD 1 EE 7 44 oleUention DEVD 1 2E Welcome to use the DEVO 12E transmitter Press ENT to transmit, “Transmitting ...... " appears in the interface. Or press EXT to exit.Press EXT to exit after another DEVO 12E received the data. Model Transmit V' E: uni.“ 1 No. 1 Transmitting (2) Model receiving Press ENT to enter Main Menu and press UP or DN to select Model Menu. Press ENT to enter Model Menu and press UP or DN to select Model Receiving, continue to press ENT to enter Model Receive setting interface. An enquiry information “Are you sure?" will be shown as below illustration. Model Receive Model Receive Press ENT to receive, ‘Connecting......" and Eliii Model Receive Connecting - - - - Are you sure? “Receiving ...... " will be shown in series in the interface. The information of “Received" with the model name will be shown after receiving is finished. Or press EXT to exit. Model Receive [W «1» Model 1 Press UP or DN to choose the save position, an enquiry information “Are you sure?" is shown after press ENT. 2 "5 Model 2 Press ENT to save or press 3 ~§ Model 3 EXT to exit. 4 ,_§ Model 4 Model Receive Model 1 Are you sure? 2.5 Model reset All the model data can be restored to factory settings via Model Reset. Press ENT to enter Main Menu and press UP or DN to select Model Menu. Press ENT to enter Model Menu and press UP or DN to select Model Reset, press ENT to enter Model Reset setting interface. It is possible to store up to 30 models data in the model list of DEVO- 12E equipment. There are two methods to reset the model data: batch reset and single reset. Model Reset : | i ll Model All I «1 y) Model 1 2 H} Model 2 3 ~§ Model 3 Batch reset: press UP or DN to select All Models, an enquiry information"are you sure?" will he appears in the interface. Press ENT to reset all models, or press EXT to exit. Model Reset Model Reset “has: All No. 1 Model 1 Are you sure? Model All Are you sure? Single reset: Press UP or DN to choose the model you want to restore. "Are you sure?" will appear after press ENT. Press ENT to reset or press EXT to exit. 2.6 Type Select This device offers three model types menu. They are Helicopter. Airplane and Glider respectively. Press ENT to enter Main Menu and press UP or DN to select Model Menu. Press ENT to enter and press UP or DN to select Type Select and press ENT to enter setting interface. Press "ENT" button to get Helicopter, Airplane and Glider selections and press UP or DN to select and press ENT to conlirm, then press EXT to exit. Type Select Helicopter DEVC! 1 QE 7 45 (JeUethion DEVD 12E Welcome to use the DEVO 12E transmitter 2.7 Trim System Trim System is able to finely tune the following six items, respectively: Elevator, Aileron, Rudder, Throttle, Left Trim and Right Trim. The trim range is divided into 20 grades (factory default is set at 4). It is convenient to subtly modify the pitch by adjusting the trim range. Trim System Press ENT to enter Main Menu and press UP or DN to select Model Menu. Press ENT to enter and press UP or DN to select Trim System, press ENT to enter setting interface. Press UP or DN to select the trim which will set, press R to increase Aileron Elevator 4I20 the trim value and press L to decrease. 4/20 Trim System For elevator, aileron, and rudder, there are two more options: Normal Elevator and Limited, press R or L you can change the setup. "Normal" means the trim is always working although the corresponding stick stays anywhere. “Limited" means the trim is out of working when the corresponding stick is at maximum position. m Press EXT to exit after finished. Aileron 2.3 Stick Position Switch According to the following setting, the switch can be used as a switch. The turn-on or turn-off position at which stick stays can also be settable. Method for setting: Press the ENT to enter Main Menu and press UP or DN to select STiCk POSltlon SW--- Ellll Model Menu. Press ENT to enter Model Menu and press UP or DN Switch to select Stick Posmon Switch, press ENT to enter Stick Position Switch setting interface. m There are four options under the Stick postion switch: SPSO, SPS1, Channel SPSZ,SPS3. Press R or L to choose the switch you want to define. Inhibit Press UP or DN to inhibit channel in naVigation mark, and press R to expand the menu.The channel includes four items: Elevator, Aileron, Throttle and Rudder. The factory default is lnhibit. Take Elevator for example. SHCK Position 5W” :llll SliCk POSifiOF‘ SW--- :IIll Press R or L to choose the SWitch I Position I ElPevatoDrNats stick, then-Pr‘ess SPSO 5w or 0 move nagiva ion mark to value of position. Its Channel possible to adjust the stick m On Up position via pressing R or L. Press UP or DN to navigate the On setting, press R or L to change the direction of the channel stick. Stick Position SW... llll Stick Position SW... l|l| :::B%:5°;Ei§ht::::lg:: Position Status “ the sketch map of the stick 0% On OriIOff direction. Check if it On I / was set correctly. “ \ Off I After finished the setting, press EXT to exit. 2.9 Device select This setting can help you configure various functional SWitches, or adiust levers. It includes Flight Main SWitch, Flight Extra Switch, Flight Mode Trim, Hold Switch, Flap Switch, Flap Trim. DEVC} 1 EE 7 4B
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 10 Producer : GPL Ghostscript 8.15 Create Date : 2014:04:15 15:22:49 Modify Date : 2014:04:15 15:22:49 Title : DEVO-12E manual 1.pdf Creator : PScript5.dll Version 5.2.2 Author : FrankEXIF Metadata provided by EXIF.tools