GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual 1
GuangZhou Walkera Technology Co., Ltd 2.4GHz Transmitter DEVO 12E manual 1
Contents
- 1. Users Manual part 1 of 11
- 2. Users Manual part 2 of 11
- 3. Users Manual part 3 of 11
- 4. Users Manual part 4 of 11
- 5. Users Manual part 5 of 11
- 6. Users Manual part 6 of 11
- 7. Users Manual part 7 of 11
- 8. Users Manual part 8 of 11
- 9. Users Manual part 9 of 11
- 10. Users Manual part 10 of 11
- 11. Users Manual part 11 of 11
Users Manual part 3 of 11
cleUethion Welcome to use the DEVO 12E transmitter DEVD 1 2E Press ENT to transmit, “Transmitting ...... " appears in the interface. 0r press EXT to exit.Press EXT to exit after another DEVO 12E received the data. Model Transmit J‘ or um“: 1 No. 1 Transmitting- - - - (2) Model receiving Press ENT to enter Main Menu and press UP or DN to select Model Menu. Press ENT to get Model Menu and press UP or DN to select Model Receiving, continue to press ENT to enter Model Receive setting interface An enquiry information “Are you sure?" will be shown as below Illustration. Press ENT to receive' llll Model Receive "Connecting ..." and “Receiving . " will be shown _ in series in the interface. The C°""ec""9 ' ' ' ' information of “Received” with the model name will be shown after receiving is finished. Or press EXT to exit. Model Receive Model Receive Are you sure? Press UP or DN to choose Model Receive Ellll Model Receive the save position. an enquiry V1 Model 1 I information “Are you sure?" is shown after press ENT. 2 "¢ Model 2 Model1 :gassoEed'il" to save or press 3 »—§ Model 3 Are you sure? ' 4 ’—§ Model 4 2.5 Model reset All the model data can be restored to factory settings via Model Reset. Press the ENT to enter Main Menu and press UP or DN to select Model Reset [W Model Menu. Press ENT to get Model Menu and press UP or DN to select Model Reset, press ENT to enter Model Reset setting interface. lt is possible to store up to 30 models data in the model list of DEVO ‘M “é Model 1 12E equipment. There are two methods to reset the model data: batch 2 ’-§ Model 2 reset and single reset. 3 ,_§ Model 3 Batch reset: press UP or DN to select All Models, an enquiry information"are you sure?" will he appears in the interface. Press ENT to reset all models, or press EXT to exit. Model Reset ul|l| Model Reset llll Single reset: Press UP or DN I to choose the model you want MM... All No. 1 Model 1 Are you sure? to restore, “Are you sure?" will appear after press ENT. Press ENT to reset or press EXT to exit. Model All Are you sure? 2.6 Type Select This device offersthree model types menu. They are Helicopter, Airplane and Glider respectively. Press ENT to enter Main Menu and press UP or DN to select Model Type Select ~/ Helicopter Menu. Press ENT to enter and press UP or DN to select Type Select and press ENT to enter setting interface. Press “ENT" button to get Helicopter, Airplane and Glider selections Airplane. . 4 and press UP or DN to select and press ENT to confirm, then press Girl | el' EXT to exit. DEvo 12E717 deUethion DEVD 12E Welcome to use the DEVO 12E transmitter 2.7 Trim System Trim System is able to finely tune the following six items, respectively: Elevator, Aileron, Rudder, Throttle, Left Trim and Right Trim. The trim range is divided into 20 grades (factory default is set at 4). It is convenient to subtly modify the pitch by adjusting the trim range. Trim System :jiii Press ENT to enter Main Menu and press UP or DN to select Model Elevator I Menu. Press ENT to enter and press UP or DN to select Trim System. press ENT to enter setting interface. m Press UP or DN to select the trim which will set, press R to increase Aileron the trim value and press L to decrease. 4/20 Trim System For elevator, aileron, and rudder, there are two more options: Normal Elevator and Limited, press R or L you can change the setup. "Normal" means the trim is always working although the corresponding stick stays anywhere. “Limited” means the trim is out of working when the corresponding stick is at maximum position. m Press EXT to exit after finished. Aileron 2.8 Stick Position Switch According to the following setting, the SWitch can be used as a switch. The turn-on or turn-off position at which stick stays can also be set‘table. Method for setting: Press the ENT to enter Main Menu and press UP or DN to select Model S1i0k Position SW--- SWitch Menu. Press ENT to get Model Menu and press UP or DN to select Stick Position Switch, press ENT to enter Stick Position Switch setting interface. There are four options under the Stick postion switch: SPSO, SPSt, SPSZ.SPS3. Press R or L to choose the switch you want to define. Press UP or DN to inhibit channel in naVigation mark, and press R to expand the menu.The channel includes four items: Elevator. Aileron. Throttle and Rudder. The factory default is Inhibit. Take Elevator for example. Stick Position SW... ”” Slim Position SW'" Press R or L to choose the Switch I Position Elevator as stick, then Press SPSO SW UP or DN to move nagivation Ch I " mark to value of position. It's anne possible to adjust the stick m Up position via pressing R or L. Press UP or DN to navigate the OPEN setting. press R or L to change the direction of the channel stick. Press UP or DN to navigate Stick Position SW... ul||| Stick Position SW... ull|l the STATUS which can check Position Status “ the sketch map of the stick 001., On OPEN/CLOSE direction. On I K \ Check if it was set correctly. K Jon I Afterfinished the setting, press “ EXT to exit. 2.9 Device select This setting can help you configure various functional SWitches, or adjust levers. It includes Flight Main Switch, Flight Extra Switch, Stunt Trim, Hold Switch, Hovering Pitch. Hovering throttle. DEVD 12E7’IB oieUeniion Welcome to use the DEVO 12E transmitter DEVO ‘i EE Press ENT to enter Main Menu, press UP or DN to move navigation D evice Select mark to select Model menu. Press ENT to enter Model menu function. —EHH Press UP or DN to Device select Option. Press ENT to DeVice select Flight Main Switch I Option interface. Flight Extra Switch Inhibit (1) Flight Main Switch: Press UP or DN to move navigation mark to Flight Main Switch and press R or L to select the desired switch. The factory default setting is FMOD SWitch. (2) Flight Extra Switch: Press UP or DN to move navigation mark to Flight Extra Switch and press R or L to select the desired sWitch. The factory default setting is Inhibit. (3) Stunt Trimt: There are two modes: Common and Flight Mode. In Common Mode all the trim values. which various sticks are corresponding to, put equall effect on all the flight modesln Flight Mode. the trim value, each of which stick is corresponding to, puts independent effect on the corresponding stick. The factory default setting is Common. Press UP or DN to choose the Stunt trim, press R or L to select “Common"or "Flight Mode", the factory default setting is "Common". (4) Hold Switch: Refer to “(1) Flight Main switch" (5) Hovering pitch: Refer to “(1) Flight Main switch" (6) Hovering throttle: Refer to “(1) Flight Main switch" After finishing the setting, press EXT to exit. 2.10 Device Output Device output can set up the output switches respectively. It can also activate. inhibit or use otherfunctions.There are eight items in total: FMOD SWitch, MIX switch,ELEV DIR SWitch, AILE D/R switch, RUDD D/R switch,GEAR switch, SPSO, SPS1, SPSZ, SPS3, left trim, right trim, AUX4 KB, AUX5 KB, AUX6 KB, AUX7 KB. Setting: Devtce Output u i I II Press ENT to enter main menu, press UP or DN to move navigation G mark to Model Menu. Press ENT to enter Model Menu. Press UP or ear DN to select Output DeVice and press ENT to enter Output Device m interface. F nct'on u i There are 7 settings Gear, AUX2, AUXS, AUX4, AUX5, AUX6, AUX7. Active (1) Gear Press UP or ON in output interface can change the gear switch. It includes FMOD, MIX ,ELEV D/R, AILE D/R,RUDD D/R, GEAR, SPSO, SPS1, SPSZ, SPS3, Left trim, Right trim, AUX4 KB, AUX5 KB, AUX6 KB, AUX7 KB. Press R or L to select the setting SWitch, The default setting is GEAR SW. DeVice Output : i i ii Gear Press UP or UN to select Function Setting after you select the switch, Press R or L can enter the interface of Gear Inhibit. Active, Gyro, GEAR SW Governor and Pitch . The default setting is Active. You can continue FunCtion to set other items after finishing. DeVice Output (2) AUX 2 Press UP or DN to enter the AUXZ interfacePress R or L can change AUXZ the AUX2 switch. it includes FMOD, MIX, ELEV D/R, AILE D/R, RUDD m I D/R, GEAR, spso, SPS1, SPSZ, SPS3, Left mm, Right trim, AUX4 Fume" KB, AUX5 KB, AUX6 KB, AUX7 KBThe default setting is FMOD SWitch. Gyro DEVD 1EE7’IB oleUention DEVD 1 2E Welcome to use the DEVO 12E transmitter Press UP or DN to select the Function Setting. press R or L to choose the switch, it inculdes Inhibit, Active, Gyro, Governor and Pitch the Device Output ill I default setting is Gyro. You can continue to set others items after AUXZ finishing. FMOD SW I Function DeVIce Output u i | || AUX3 (3) Auxs — RUDD DIR I Press UP or DN to enter AUX3 interface. Press R or L can change . the AUX3 switch. It includes RUDD DIR, GEAR, SPSO,SPS1, SPSZ, Fund'on SPSS, Left trim, Right trim,AUX4 KB, AUX5 KB, AUXS KB,AUX7 KB. Gyro The default setting is RUDD D/R switch. Device Output Press UP or DN to move navigation mark to Funtion Setting. Press R or L to desired item.The optional items are Inhibit, Active, Gyro, AUX3 Governor and Pitch. The factory default is Gyro. Continue to set up RUDD DIR I other items after setting finished. Function (5) AUX4, AUXS, AUXS, AUX7 settings please refers to AUXS settings. AUX4 default setting is AUX4 KB; AUXS default setting is AUXS KB: AUXS default setting is AUXS KB: AU><7 default setting is AUX7 KB. After finishing the setting, press EXT to exit. 2.11 Swash Type The swash type is grouped into six options: 1 Servo Normal, 2 Servos 180°, 3 Servos 120°,3 Servos 140“, 3 Servos 90° and 4 Servos 90°. Swash Type a i i ii Press ENT to enter Main Menu, press UP or DN to move navigation mark to Model Menu. Press ENT to enter Model Menu. Press UP or UN to select Swash Type and press ENT to enter Swash Type interface. 2 Servos 130° Press UP or DN to choose the required "Swash type", press ENT to 3 Servos 120° confirm, the corresponding items will have the"«/" mark in front of the 3 Servos 140“ items. Press EXT to exit after finishing. 2.12 Power Amplifier The transmission output power of DEVO 12E is adjustable. It is divided into six grades from small to big. The lower the transmission output power transmits, the shorter the radio range is, and the longer the stand- by time will be, the higher the transmission output power, the farer the radio range, and the shorter the stand- by time. Choose the appropriate transmission output power according to the actual situation. Press ENT to enter Main Menu, press UP or DN to move navigation mark to Model Menu. Press ENT to enter Model Menu. Press UP or DN to select PowerAmplifier and press ENT to enter PowerAmplifier interface. PowerAmplifier ul||| Press UP or DN to choose the desired output power value. Press V +20 dBm ENT to confirm then the corresponding items will have "¢"mark in front of the items. +15 dBm +10dBm T I I I I Grades Grade 5 Grade4 Grade3 Grade2 Grade1 *5 dBm zodem 15dBm 10dBm 5dBm OdBm -5dBm After the setting, press EXT to exit 2.13 Fixed ID This setting will bind DEVO 12E with its receiver in a unique corresponding relationship. It Will greatly speed up the time of automatic binding when DEVO 12E power on. DEVD 1 EE 720 oleUention DEVD 1 EE Welcome to use the DEVO 12E transmitter (1) Setting for fixed ID The setting for fixed ID should be under the status that automatic ID binding is successfully finished. Below is the setting method. Press ENT to enter Main Menu, press UP or DN to move navigation mark to Model Menu. Press ENT to enter Model Menu. Press UP or DN to select Fixed ID and press ENT to enter Fixed ID setting interface. Fixed ID IIII Fixed ID I I I I If you want to activate the fixed ID setting, press R or L to change the status from off to Status “ Status “ on. A series of random digits will be shown below after ID Code 326186 changing to on. Fixed ID DIIII Press UP or DN to choose the ID code setting, press R or L to coose Status On the words or number. press UP or DN moves to the next code setting . there are 6 words can be set to ID code. ID Code E26186 Press ENT after the new ID has been set An inquiry interface of “Are you sure?" pop up. “ID Code Matching .. Will be shown after press ENT. After matching, the interface will be returned to Model Menu. Fixed ID Fixed ID EIIII Fixed ID ID Match - - - - Are you sure? (2) Fixed ID cancellation Insert the assorted BIND PLUG into the output terminal of BATT before the receiver power on. and then plug 5V DC power into other output terminal. The red light of receiver Will flash slowly. This means the fixed ID code has been cancelled. Pull out bind plugDEVO 12E also need to make relative cancellation and revision after the fixed ID in receiver is cleared out. In the main interface press the ENT to enter Model Menu and then press UP or DN to move the navigational mark to select Model Menu. A Press ENT to enter Model Menu. Press UP or DN to select Fixed ID H code and push ENT to enter the Fixed ID code interfacePress UP M 7 or DN to select STATUS option. Press R or L to change the status to off. Then press EXT to exit. 2.14 Sensor setting Setting method: press ENT enter to the Main Menu. Press UP or DN to select the Model Menu. Press ENT enter to Model Menu. Press UP or DN to select sensor press ENT enter to the sensor setting interface. See the Illustration. Sensor Setting II I I sens” Slams Press R or L to select Activate or Inhibit (the default setting is Inhibit), m such as press Activate will includes No Signal Warning,Voltage sensor,Temperature sensor,GPS receiver setting etc. DEVD ’I BE iE’I (JeUethion DEVO 12E Welcome to use the DEVO 12E transmitter (1) N0 Signal Warning Sensor Setting Press UP or DN to make the navigation mark to choose “No Signal Warning". Press R or L to choose " Inhibit" or “Active"(default setting is" inhibit“). If you choose “Active", the Radio will alarm when telemetry signal lost. Picture as right: Sensor Status Active No Signal Warning There are 3 different types of voltage can be measured.lt includes Internal 5V,External V1 and V2 which can be monitored two different external voltage(i.e. battery) respectively.0nce the measured voltage is lower than the setting value, the Radio will alarm. (2) Voltage setting (2.1) Receiver 5V(|nternal) PFV(Power Feeding Voltage) Alarmed value can be setted as 3 6- Voltage setting: press R or L to activate the 5V, the alarm interface will appear in the interface , please refer to the lllustration. Voltage H l l Voltage H" Press UP or DN to select the internal; 5v I lnternal: 5v I Alarm Voltage setting,press m Active R or L to set the value. The Alarm Voltage range is 3.6-6V. you can continue to set other items after you finished. (2.2) External V1 Press UP or DN enter to External V1 setting interface. Press R or L to activate the V1, the details refers to the lllustration. Voltage m. Voltage Press UP or DN to select the External: V1 External: V1 Alarm Voltage setting. Press m Active R or L to set the value. The Alarm Voltage setting range is 0.2~99.9V. Alarm Voltage you can continue to set other 0.2 V items after you finished. (2.3) External: V2 setting can refer to External V1 setting. Press EXT back to sensor setting interface after you finished. (3) Temperature sensor The temperature sensor can measure up to 4 different lemperature(i.e.motors).You can choose Celsius or Fahrenheit.The alarmed value can be setted to 4 different temperature.0nce the measured value is higher than the setting value,the radio will alarm.The Alarm Temperature value can be setted as -20-220‘C or - 4.0~428.0” F. Temperature in I Temperature Setting: W Unit I In the “Sensor Setting“interface, press UP or DN to make the navigation ‘ mark to choose “Temperature Sensor". and press ENT to enter T1 Inh'b‘t “Temperature Sensor"setting interface. See the illustration. T2 Inhibit (3.1) Unit Press UP or DN to make the navigation mark to choose “Unit"setling item,and press R or L to choose Unit, two kinds of Unit:CeIsius and Fahrenheit. (3.2) Alarm Temperature settings Press UP or DN select the T1 ,Press R or L to Active the setting. Inhibit Will change to Active and Alarm temperature Will be shown. If you choose Inhibit, the Alarm temperature value won't be shown. DEVD 1 BE 7 22 oleUention Welcome to use the DEVO 12E transmitter DEVC] 1 2E Press UP or DN to select “Alarm"setting, press R or l_1o set the alarm T t . . . w temperature value. Press UP or DN to set other Items after finishing Unit Celsms the setting. T1 Active Alarm _ (3 3) T2, T3, T4 setting T2 Inhibit Refer to the step of “(3.2)T1". (4) GPS setting GPS Setting a l | II There are 4 items including Altitude Type,Speed Unit, Date Type and Altitude TYli’e Time Zone in the GPS receiver setting interface. Absolute Press UP or DN to select the Sensor setting interface to enter the Speed Unit GPS setting interface Knots (4.1) Altitude Type Press UP or DN to select the Altitude type on the GPS setting interface and it's Absolute and Relative. (42) Speed Unit GPS Setting all“ GPS Setting Di... Press UP or UN to select the Altitude Type I Altitude Type I Speed Unit on the GPS setting _ interface and it includes knots Relative Relative and km/h and relative. Select Speed Unit SPEEG Unit (4.3) Date Type Press UP or DN to select the Date Type on the GPS setting interface and it includes DD-MM-YY,MM-DD- YY and YYVMMVDD. Select the desired item. GPS Setting :llll GPS Setting DH“ (44) Time Zone Date Type Date Type Press UP or DN to select the DD-MM- DD’MM’YY Time Zone , pressRorLto Time Zone Time Zone set the desired Time Zone. UTC+08:00 UTC+08:DD 3.0 Functi Menu Function Menu can help you custom adjustments for the selected models. The rnenu include items such as Reverse Switch, Travel Adjust, Sub Trim, Dual Rate and Exponential. Throttle Hold, Throttle Curve, Mix to Throttle.Gyro Sensor. Governor.Tail Curve. Dual Pitch Swash Mix .Pitch Curve, Program MlX, Monito ,Fail Safe, Sensor view, Trainer and Timer. 3.1 Reverse Switch Press ENT to enter Main Menu; Press UP or DN to move the navigation mark to Function Menu. And press ENT to enter Function Menu, Press UP or DN to choose Reverse Switch and Press ENT to enter into Reverse SWitch interface. Reverse Switch Elevator Aileron Press UP or DN to move navigation mark to ELE(taKe Elevator for example). Press R or L to shift the status between nomal and reverse. These are two status for option. And the default setting is Normal. All Channels Reverse Switch like: Aileron, Throttle, Rudder, Gear, Pitch, AUX2, AUX3, AUXA, AUX5, AUX6 and AUX7 can be referred to the way of ELEV Reverse Switch. And press EXT to exit after finishing setting. Reverse Switch Elevator Reverse Aileron Normal DEVD ‘l EE 723 oleUention DEVD 1 EE Welcome to use the DEVO 12E transmitter 3.2 Travel Adjust Press ENT to enter into Main Menu. Press UP or DN to move naVigation mark to select item Function Menu. Press ENT to enter Function Menu. Press UP or DN to select Travel Ajust, Press ENT to enter Travel Adjust interface, as below illustration. It shows the Travel Adjust status of one channel: Travel Adjust Take ELEV for example, Press UP or DN to move navigation to — desired item Elevation of U. Press R or L to increase or decrease Elevator the servo travel range. The adjustment range is from 0.0% to 150.0%. The factory default is 100.0%. Press UP or DN to move navigation mark to deSired item D of ELEV. D100.0% Press R or L to increase or decrease the servo travel range. The range is from 0.0% to 150.0%. The tactory default is 100.0%. All other channel’s Travel Adjust like Aileron, Throttle, Rudder, Gear, Pitch, AUXZ, AUX3, AUX4, AUXS, AUXG and AUX7 can be referred to ELEV travel Ajust. Press EXT to exit after setting finished. 3.3 Sub Trim Sub Trim can move the neutral point of the servo. But we advise you to mechanically adjust the servo bell crank it offset is far away from the neutral point of servo, because excessive usage ofthe sub trim may damage the servo. Setting method: SUb Trim :Iiii _ Elevator I Press ENT to enter Main Menu, Press UP or DN to move the navigation mark to select item Function Menu. Press ENT to enter Function Menu, ' ° Press UP or DN to select Sub trim. and press ENT to enter Sub Trim Aileron interface. 013% The interface show the items and the channels which are adjustable. Press R or L to change theI neutral point of Servos. The lactory default is 0.0%. Press UP or DN to choose desired items The range as below: Channel name Adjustment range Channel name Adjustment range Elevator 062.5% ~ U62.5% -62.5% ~+62 5% Aileron R62.5% ~ L62.5% AUX3 -62.5% ~+GZ 5% Throttle L62.5% - H62.5% AUX4 -62.5"/o ~ +62.5% Rudder R62.5% ~ L62.5% AUX5 -62.5% ~ +62.5% Gear -62.5% ~ +62.5% AUXG -62.5"/e ~ +62.5°/o Pitch L62.5% ~ H62.5% AUX7 -62.5% ~ +62.5% Press EXT to exit after adjustment finished. 3.4 Dual rate and Exponential After this function is set up, it is possible tor D/R switches to control the dual rates of elevator, aileron and rudder, respectively. The setting range is covered from 0% to 125%. Under the help with exponential curve adjustment, it is possible to make both customized setting and automatic setting. The switch between Dual rate and Exponential can be performed via pushing or pulling the Flight Mode Lever. Setting method: Dual Rate and EX... [Hll Press ENT to enter Main Menu Press UP or DN to move navi ' Channel V ’ . I . gation mark to desired item Function Menu Press ENT to enter Function m Menu, press UP or DN to choose Dual rate and Exponential, Press Position ENT to enter DIR and Exponential interface. Pos 0 J DEVC} 1 2E 724 cieUeniion Welcome to use the DEVO 12E transmitter DEVD 4 2E (1) Channel selection Press UP or UN to move navigation mark of Channel, Press R or L to set up channels containing Elevator, Aileron and Rudder. Choose the desired channel for setting. (2) Position selection Press UP or DN to move navigation mark to desired item Position In the manual mode, the function of Dual rate and Exponential will be executed by the corresponding D/R sWitch among P050 and Post . Take the item Elevator at channel as an example. It's possible to shift between Post) and Post via pushing or pulling the D/R sWitch Dual Rate and EX... Ellll (3) Dual rate adjustment Position . . . P05 0 Press UP or DN to move the naVigation mark to desired item Dual Rate. It’s possible to change the dural rate value of Postion via Dual Rate pressing R or L and the corresponding value curve in the right top 100% of interface Will be changed accordingly. The factory default is 100%. (4) Exponential Dual Rate and EX... Press UP or UN to select Exponential item of navigation mark. It's Dual Rate possible to change Dual Rate and Exponential value in Pos when 100% pressing R or L to change the value. There are;100% and Line three adjustment. At the same time. the corresponding curve Will be changed and shown at the right graph. Exponential (5) Automatic setting Under working with Flight Mode, it's possible to switch between the Dual Rate and Exponential, which are set in above"(3) Dual Rate adjustment" and "(4) Exponential adjustment", respectively. : Flight Mode The setttings for Normal Mode, Stunt 1, Stunt 2, Stunt 3, Stunt .7 : 4 and Throttle Hold are available. But for Stunt 3 and Stunt “ I i n i 4, Flight Mode Extra SWitch at DeVice Select in Mode Menu a should be activated(Refer to "2.9 Device Select"), and Throttle s: Hold in Function Menu should be set as Active(Refer to "3.5 e Throttle Hold" below). ‘ e ‘ (5.1) Normal Flight Mode setting: Press UP or DN in the navigation mark of Dual rate and Exponential Dual Rate and EX"- to select the desired item Normal Flight. Press R or i. to set the position Normal Mode and the Switch. Only the DIR switch control is valid When Switch is selected, under the Flight Mode, it’s possible for Pos lo SWitch the m dual rate and exponential, which are set in above(3) and (4)Exponential Stunt 1 adjustment. The settings for Swtich, PosO, Pos’l, P052 . Pos3, Pos4 SWitch and P055 are valid. (5.2) The setting for Stuntt, Stunt2. Stunt3. Stunt4 and Throttle Hold can be set up according to above Normal Flight Setting. Press EXT to exit after finishing the setting. 3.5 Throttle Hold If this function is set. the switch will be exectuted by hold switch. The setting value of throttle hold is ranged from 720.0750.0% the default setting is Inhibit. DEVO ’l EE 725 oleUenlion DEVD 1 EE Welcome to use the DEVO 12E transmitter Setting method: Press ENT to enter Main Menu. Press UP or DN to move navigation mark to select Function Menu. Press ENT to enter Function Menu. Press UP or DN to select Throttle Hold. Press ENT to enter Throttle Hold interface. as below illustration' Throttle Hold Hold Status Throttle HOId Press R or L to activate Hold Status Throttle Hold function, and expansion list will be shown m as Throttle hold status. Hold Hold Position position Throttle Stick and _ 50% Hold SWitch. (1) There are two items under Throttle Hold Status: Active and Inhibit. The factory default setting is Inhibit. (2) Hold Position In the Throttle Hold interface. press UP or DN to make the NaVigation mark to choose "Hold Position" setting options. Press R or L to change data. the minimum value is -20.0%; the maximum value is +50.0%. (3) Throttle Stick Throttle Hold on the interface "Throttle hold". choosing the Throttle Stick by button — UP or DN. press R or L. the expansion list Will be shown as Inhibit Throttle Stmk and Active. default setting is Inhibit. if turning Active. menu "amount m decrease" Will be seen. you can set it by button UP or DN. data changes will be vontrolled by R or L. the minimum is 0.0% and the C‘” P°5“‘°" maximum is 100.0%. (3) Throttle Switch setting Throttle Hold :iiii W It's invalid for setting. the factory default is RUDD DIR which Will be shown in the status item. When the Throttle Hold switch is on. data RUDD D/R under the Throttle Hold can not be amended until Throttle Hold sWitch Status I to be off. and the hold status is changed. “ Press EXT to exit after setting up finished. 3.6 Throttle Curve Throttle curve are adjusted through seven points. which of all the flight modes can be respectively set. The flight mode include Normal Flight. Stunt 1. Stunt 2. Stunt 3 and Stunt 4 while Flight Modes Extra SWitch in Device Select should be activated(Refer to "2.9 Device Select"). Press ENT to enter main menu. Press UP or UN to move navigation mark to select Function Menu. Press ENT to enter Function Menu. Press UP or DN to select Throttle Curve. Press ENT to enter Throttle Curve interfaceThe enquiry dropdown ls shown"A|l servos hold?" If Throttle CW9 ”H” “mm Curve :iiii select OK. all the servos will Fugm Mode ._0_ _ 0.0 I be locked at the current status. All Servos Hold? if click Cancel. all the servos m will be unlocked at the current OK Cancel Exponential status. Ofl nus—no (i) Flight Mode There are total five flight modes: Normal Flight. Stunt 1. Stunt 2. Stunt 3 and Stunt 4. The Curve of which can be respectively set in their corresponding flight mode. The setting method is to press UP or DN to select Flight Mode in Throttle Curve interface. The corresponding flight mode Will be shown when the Flight Mode switch shifts via pushing or pulling the Flight Mode Switch. And the exponential can be adjusted after Flight Mode is selected. DEVD 1 BE 7 26
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Frank Create Date : 2014:04:15 17:30:33-07:00 Modify Date : 2014:04:15 17:30:33-07:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2014:04:15 15:32:04+08:00 Format : application/pdf Creator : Frank Title : DEVO-12E manual 1.pdf Producer : Acrobat Distiller 10.1.8 (Windows) Document ID : uuid:606d2b5d-e99e-4720-850d-09cca6a684f7 Instance ID : uuid:b9ec3f56-2862-4af0-be64-daddfbbff56e Page Count : 10EXIF Metadata provided by EXIF.tools