GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual 1

GuangZhou Walkera Technology Co., Ltd 2.4GHz Transmitter DEVO 12E manual 1

Users Manual part 4 of 11

Download: GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual 1
Mirror Download [FCC.gov]GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual 1
Document ID2246009
Application IDvhhzY35Of3si6HJEbqniHA==
Document DescriptionUsers Manual part 4 of 11
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize399.02kB (4987789 bits)
Date Submitted2014-04-18 00:00:00
Date Available2014-04-18 00:00:00
Creation Date2014-04-15 15:21:17
Producing SoftwareGPL Ghostscript 8.15
Document Lastmod2014-04-15 15:21:17
Document TitleDEVO-12E manual 1.pdf
Document CreatorPScript5.dll Version 5.2.2
Document Author: Frank

oleUention
Welcome to use the DEVO 12E transmitter
DEVD 1 EE
(2) Exponential setting Throttle Curve nilll
Press UP or UN in the “Throttle Curve" setting interface to select Flight Mode 0_o_ . _ 00 I
“Exponential“ setting. Press R or L to set “Off" or “On". The throttle .
curve will being changed smoothly if select On. Select Off if not need Normal...
then the throttle curve will be shown as a line. Exponential
m Li mm
(3) Curve setting
It includes two items: Point and Output.
(3.1) Point setting
Press UP or UN in Throttle Curve interface to select Points setting. Press R to expand a list including seven
points: “Point-L", “Point-1",
“POint-Z", "Point-M", “Point-3”, Throttle Curve Throttle Curve
“Pointr4" and “PointeH". Press Point '1 - Point
R or L to select the point you P
want to adjust. _ m
Status
rm: Inhibit Lima;
Throttle Curve D ‘ I ll (3.2) Status setting
P't—Uu Press UP or UN to move navigation mark to Status and press R or
oIn - - .
L to choose Inhibit or Activate. Select Inhibit if keeping the current
Point _ M value(the default setting is inhibit). Select Active for changing the
Status above points' value.
m ' . .4 Note: After select point -l_ or Point-H, the status setting won't be
Lt 2M3 4 H
display.
(3.3) Output adjustment Throttle Curve ujjjj
An expansion list of Output and Hover items Will be shown after Output 09- ~ » 0°
ESTES‘BEiE‘i $211“th 851$"? L” 30°iTSZZslaZ'SZL'ELZSJtQE ‘
amount of selected point with a minimum of 0.0% and a maximum of Hovering
100.0%. On L1 2mm I
(3.4) Hovering Adjustment
After the setting of (3.3) Output adjustment is finished. it’s necessary to set the item of Hovering as 0n and
all the selecled points of the throttle curve should be activated if using throttle trim in flight is a must.The five
points of 1-2,M,3—4 in the curve will being paralleled or down with the changing of throttle trim. So the throttle
curve will being paralleled up or down with the movement of the five points
Press EXT to exit after finish the setting.
3.7 Mix to throttle
This Function can keep the main rotor blades running at the certain revolution caused by the changed load when
operation the aileron servo, elevator servo and rudder servo. Generally, it's not advised to use the function.
Setting method
Press ENT to enter Main menu. Press UP or DN to move navigation mark to select Function Menu. Press
ENT to enter function menu. Press UP or DN to select Mix to Throttle. And press ENT to enter Mix to throttle
interface as in below illustration.
Mix to Throttle iiii
There are three settings: elevator, aileron and rudder. If the item of
Elevator Channel is shown as Elevator, there are UP, DOWN and Switch in
Up I the interface. If the item of Channel is Aileron or Rudder, the contents
Down 0% in the said interface will be changed into Left, Right and Switch. Take
the example of Channel set as Elevator to illustrate the setting method.
Switch On
DEVD ’l EE 7 27
JeUethion
DEVD 1 2E Welcome to use the DEVO 12E transmitter
(1) Up setting
In the Mix to throttle interface, press UP or DN to move the navigation mark to select UP item. Press R or L
to increase or decrease the mix amount when moving the throttle stick upwards.The bigger the amount is,
the bigger the mix to throttle Will be. Change the amount from “+" to “-“ for the throttle mix direction Reversing.
The adjustable range is 2125%.
(2) Down setting
In the interface of Mix to Throttle. press UP or DN to move the navigation mark to select Down item. Press
R or L to increase or decrease. respectively, the mix amount when moving the throttle stick d wnwards. The
bigger the amount is. the bigger the mix to throttle Will become. Change the amount from ‘ ‘ for the
throttle mix direction Reversing The adjustable range is 1125%.
(3) Switch Selection
In the interface of Mix to Throttle, press UP or DN to move navigation mark to select Switch item. Press ENT,
an expansion list of Always on. Normal Mode. Stunt ‘l. Stunt 2. Stunt 3. Stunt 4 and Gear is shown. After
setting finished. Aileron or Rudder can be set via pressing DN.
(4) The setting of Aileron or Rudder. and Mix to Throttle can be referred to Elevator setting. Press EXT after
setting finished.
Note:
(1) Before the flight, please confirm: All above amount of mix to throttle is proper enough to offer a good flight.
And make sure all the actions in different flight mode are normal.
(2) The function is in spare when governor is working.
3.8 Gyro Sensor
This function supply the GYRO sensitivity adjustment.both through switch ‘D/R' to Manual and “Flight Mode
"Automatic switch different sensitivity.
Gyro Sensor
Setting method:
Press ENT to enter Main menu. Press UP or DN to move navigation Mode
mark to select Function Menu. Press ENT to enter function menu.
Press UP or UN to select Gyro Sensor. And press ENT to enter Gyro
Sensorinterface. Channel
(1) Manual Setting
(1.1) Manual Setting
In the Gyro Sensor interface. press UP/DN to choose “mode"project set. press R/L to selectable set (“Manual
set" and “Automatic set").Then choose “Manual" option.
(1.2) Channel
The original channel is “AUXZ”. if you want to change to other channels control. you can choose from
“Output"set.(refer to “2.10 Output").
(1.3) SWitch choose
In the Gyro Sensor interface. press UP/DN to choose “SWitch “project set. press R/L to selectable sets “FMOD
SW", MIX SW, ELEV DIR. AILE DIR, RUDD D/R.GEAR SW. totally 6 selectable sets.Choose the Manual
control switch.
(1.4) Sensitivity Setting
If choose 3 SWitches.there are “position 0"."position 1" and “position 2".then set the sensitivity individually; If
choose 2 switches.there are “position 0" and "position 1" . then set the sensitivity individually.
(1.4.1) position 0
Turn the choosed GYRO Control Switch. make the status display
present switch status "position 0" Press UP or DN to choose “position
FMOD SW 0", press R or L to increase/decrease value individually. If the GYRO
Status have “NOR" mode and “AVCS” mode. when the value lower than
50%. it is “NOR"mode. The lower of the value is. the bigger of the
GYRO sensitivity becomes. The factory default value is 50%.
Gyro Sensor
Switch
050
DEVD 1 EE 7 28
oieUeniion
DEVD 1 2E
Welcome to use the DEVO 12E transmitter
(1.4.2) “Position 1“," Position 2" are the same setting way as above “position 0".
(2) Automatic setting Gyro Sensor
(2.1) Automatic Setting Mode
In the Gyro Sensor interface. press UP or DN to choose “mode" project
set, press R or L to selectable sets (“Manual set" and "Automatic
set").Then choose "Automatic" option. Channel
(2.2) Channel
The original channel is “AUX2”.if you want to change to other channels control.you can choose from
“output"set.(refer to "2.10 output").
(2.3) Switch: There is no use in the Automatic Setting.
(2.4) Status
Turn the Switch “flight mode"or “Throttle hold",the status set display present flight mode position.There are
Normal Mode, Stunt 1, Stunt 2 , Stunt 3 ,Stunt 4, Throttle hold sets "Throttle hold" need to start that can
effect.(refer to “3.5 throttle hold")
(2.4.1) Normal Mode Gyro Sensor nilll
Press UP or DN to choose “Normal Mode“ pro)ect set, press R or L Status
can increase or decrease the value individually.” the GYRO have
“NOR"mode and “AVCS”mode, when the value is lower than 50%,it Normal Mode I
is “NOR"mode. the lower of the value is ,the bigger of the GYRO Normal Mode
sensitivity becomes. The factory default value is 50%.
(2.4.2) Stunt 1, Stunt 2, Stunt 3, Stunt 4, throttle hold settings refer to “Normal Mode".
Afterfinishing the set,press EXT to exit.
3.9 Governor
Before setup this function, “Governor“ should be set and activated in “output" interface. (Refer to 2.10 Output)
It is possible to set Governor control rate in various flight modes seperately. Please setup the Governor for
the desired retation speed. The transmitter display data is only for percentage reference. The real rotation
speed refer to Governor.
Setting method:
Governor
Press ENT to enter Main Menu; Press UP or DN to move make
navigation mark to select functional menu. Press ENT to enter
functional menu; Press UP or DN to choose Governor then through
the ‘ENT’ key to the Governor setting intenace,which display the status
and channels; Press UP or DN can see the Normal Mode, Stunt 1,
Stunt 2, Stunt 3, Stunt 4, Throttle Hold and so on.
(1 ) Status
Toggle the Flight Mode or Thottle Stick Lock switch, the status display present flight mode position.There
are “Normal Mode", "Stunt 1", "Stunt 2", " Stunt 3", "Stunt 4". "Throttle Hold" and so on."Throttle hold" need
to start that can effect.(refer to “3.5 throttle hold“)
(2) Channel: displaying in "2.10 output" have set the Channel.(refer to 2.10 Output)
(3) Normal Mode
Press “UP/DN" to make the navigation choose the “Normal Mode"set,
press R/L to increase/decrease the valueThe factory default value
is 0%.
(4) The method to set "Stunt1 tunt2", "Stunt3", "Stunt4 ", "Throttle
Hold" refer to “Normal Mode".
After the set finished. press EXT to exit.
Status I
Normal Mode
Channel
AUXZ
Governor
Normal Mode
0%
Stunt ’l
DEVD 1 2E 729
JeUethlon
DEVD 12E
Welcome to use the DEVO 12E transmitter
3.10 Tail Curve
This function is mainly used for amending the reaction torque produced by pitch angle oi main rotor bladesln
the set flight mode,the mix amount can be automatically SWitched when moving the flight mode (FMOD)lever.
Press ENT to enter the Main Menu; Press UP or UN to make the naVigation mark to choose the functional
menu; Press UP or DN to choose "Tail Curve", then press ENT, there will be shown an enqury of “all Servo
hold?" select ok tor locking the current status ofall the Servos,and cancel for unlocking the current status oi
all the Servos; Afterfinish the Ta'l C r e Ta'l C rve
choose, press ENT to “Tail I u V 5"“ ' u Dl|||
Curve" interfaceThere are FIightMode "P9,. ,2 I
current flight status,curve All Servos Hold? m
graph and adyustaole items.
OK Cancel PM“
(1) Flight Mode ”mm“ Li 2M“ H
In the “Tail Curve" interface, press UP/DN to make the navigationg mark choose “Flight Mode" set .Toggle
the fli ht mode switch and shown the current flight mode. In the set of flight mode can set “pitch","exponential
curv curve point setting",arid “output "items.
(2) Pitch
Press UP/DN to make the navigation mark choose “Pitch" set, press R/L to choose the two options Normal
and Original. Select the desired item.
Tail Curve
(3) Exponential Curve
Exponential
Press UP/DN to make the navigation mark choose “Exponential
Curve"set, press R/L to choose two options ON and OFF.The curve
will be smoothly changed if touching on.SeIect the desired item.
Point
Point - L
(4) Curve Point Setting Lt éMélH
Press UP/DN to make the navigation mark choose “Curve Point" set.
TailCurve— (4.t) Point Selection
Exponential Press RIL to set the Curve Point options “point-L“, “point-one", “point-
On 2", “pointeM", “point73". “pointr4", “pointeH", totally seven options;
Point Select the point which you want to adjust.
W Li mm
(4.2) Statues Setting
Press UP or DN option to choose the State setting after adjusting the Tail Curve Dl|||
date point. Press R or L keys, there are two options of “Inhibit” or Status {09, _ ,Q
“Active"(Choose “poll’iFL” or ”point 7H”. there is no state menu that
Will be shown).lf you don‘t want to change the date,then Choose m
“Inhibit"(default setting is “Inhibit"). If you want to change the date, Output
then choose “Active“. “Output “ item will be expanded. 0W" ..... A I
Lt 2M3 4 H
(4.3) Output Setting
Press UP/DN to make the navigation mark choose “output" set, press R to increase point's output; the minimum
amount is +100%; press L to decrease point’ output amount: the maximun amount is -100%.
(4.4) The methods to set “Stunt 1"
finished, press EXT to exit.
"Stunt 2", “Stunt
Stunt 4", “Throttle Hold" refer to “Normal Mode".after
Notes: If an AVCS Gyro is used,this function is not necessary.
DEVD 1 EE 7 30
oleUention
DEVCJ 1 EE
Welcome to use the DEVO 12E transmitter
3.11 Dual Fitch
The " Dual pitch " should be activated in " Device output " ifwant to set this function. Seven-Point adjustment
method is allowed to set up all the pitch curves respectivly, in each flight mode, which includes Normal flight,
Stunt 1, Stunt 2, Stunt 3, Stunt 4, Throttle Curve. "Throttle Curve should be activated if want to use ( refer
to "3.5 Throttle Curve "Stunt 3" . " Stunt 4" .The Flight Mode Extra Switch should be activated in " Device
Select" , refer to 2.9 DeVice Select.
Setting method: Dual Pitch in.
Press ENT to enter Main Menu, and then press UP or DN to move Channel
the navigational mark to select Function Menu.Press ENT to enter m
the Function Menu and then press UP or UN to select Dual Pitch and
press ENT to enter the Dual F'itch interface which Will show the setted
output channel.
Press DN to select "Point< L"; Press R to increase point output values, the maximum is +100%, Press L to
decrease pointoutpul values, the minimum is -100%.
Dual Pitch Press DN and then appear "Point-L", "Point-1", "Point-Z", "Point-3",
— "Point-H", "Point>H". "lnhib't" and " Act' e" can be selected in the
Pomt < L lollwoing: " PointrL",“Point7 , "Point72","Pointr3", "PointrH". Press
R or L to select " Active" if want to adiust. then press UP or DN to
set the values, press R or L to adiust the values (the value is 0% if
don't change ), "i" (beside the values) means amend direction, the
adiustable range is i100%.
3.12 Swash Mix
This function, which can be executed through flight mode, is used for amending the variation caused by
swashplate movement, when the aileron or elevator is working.
Press the ENT to enter Main Menu and then press UP or DN to choose the navigation mark of enter Function
Menu. The interface Will show the Swash Mix Setting after press the ENT. The “Swash Mix" item is only
afieCted after choose mile MO Swash Mix :iiii Swash Mix aim
or more servos in 2.11
Swash Type".Take the third Swash Type Swash Type I
servu120° as an example. 3 Servos 120.
. Aileron
New" +60%
(1) Swash Type
The item will show the current swash type if choose the two or more servos in “2.11 Swash Type". the choosed
swash type is the third servo 120" .
(2) Aileron Mix Adjustment
In the interface of Swash Mix,press UP or DN to choose the navigation mark of Aileron Setting item. Press
R button to increase the rate and l. to reduce. If reversed direction, it is available to chang through the "+" or
"-" mark. The adjustable rate is L 125%. After finish the settings, press DN to set others.
Swash Mix uilll
(3) Elevator mix adjustment
Aileron
The function is based on the three or more servos which is choosed(refer +60%
to the 2.11 Swash Type).The setting method is same as above. Elevator
(4) Pitch Mix Adiustment
The function is based on the two or more servos which is choosedtrefer lo the 2.11 Swash Type).The setting
method is same as above.
DEVD 1 2E 731
JeUethion
DEVD 12E
(5) Exponential Cun/e
Welcome to use the DEVO 12E transmitter
This function can execute the exponential changes. which are set at Dual Rate and Exponential in Function
Menu when it is started. If Off is selected. the exponential curve will be changed in the form of fold line.
Setting method: Swash Mix nilll
Press UP or DN to touch the navigation mark of Exponential to expand Pitch
two options: Off and On. the default setting is Off. On is recommended. ,GW
Please press EXT key to exit after finished. Exponential
3.13 Pitch Curve
7-point adjustment method is allowed to set up all the pitch curves, respectively, in each flight mode, which
includes Normal Mode, Stunt 1, Stunt 2, Stunt 3, Stunt 4, and Throttle Hold. The Flight Mode Extra Switch in
Device Select should be preViously chosen. Refer to "2.9 Device Select".
Setting method:
Press ENT to enter Main menu. Press UP or DN to move navigation mark to select Function Menu. Press
ENT to enter function menu. Press UP or DN to select Pitch Curve. And press ENT to enter ENT to enter
function menu. Press UP or DN to select Pitch Curve, press ENT to enter Pitch Curve interface. there is
"All servos hold?". press ENT
to confirm with OK for all the
servos Will be locked at the
current states. Or use UP or
Pitch Curve |lll Pitch Curve uj|||
400 I
Flight Mode "99-
DN to Cancel for Unlocked. A“ Servos Hold. m
Enter the next interface after OK Cancel Exponential
confirmed OK or Cancel. Off Li 2mm
(1) Flight mode
Press UP or DN to select the Flight Mode at the interface of Pitch Curve. and then move the switch of flight
mode, the state of flight mode will be shown. The Pitch Curve can be set at the current state. There are
“Normal Mode", “Stunt 1", “Stunt 2" ,"Stunt 3", "Stunt 4" and “throttle hold" 6 flight modes.The “Normal Mode"
is made as an example for your referrence.
(2) Exponential
Press UP or DN to choose the setting item of Pitch Curve .There are ON or OFF option when you press the
R or L buttoms.The Curve Pitch will become round if the ON buttom is choosen. If you don’t adjust the Pitch
Curve Funtion, then choose OFF buttom.
(3) Setting of Curve Point
Press UP or DN to enter the setting interface of Curve Point. Press R or L keys of setting curve point.there
are “point-L“,“point -1", "point -2", "point -M", “point -3", “point —4", “point -H".Choose the points need adjusting.
(4) Status Setting
Press UP or DN option to choose the State setting afler adjusting the
date point.Press R or i. keys,there are two options of “Inhibit“ or
“Active"(Choose “DDlnPLVV or “point 7H",there is no status shown in the
menu).lf you don’t want to change the date. then choose “Inhibit"(default
setting is "Inhibit"). If you want to change the date,then choose “Active",
“Output " item will be expanded.
Pitch Curve
Point "9‘? »
Point , 1
Status
LizMédPi
(5) Output Setting
Press UP/DN to make the navigation mark choose“output" set, press R to increase points output;the minimum
amount is +100%;press L to decrease point‘ output amount; the maximun amount is 400%.
DEVD 1 EE 7 32
JeUenlion
Welcome to use the DEVO 12E transmitter
DEVO 1 2E
(6) Hovering Setting
-100 -100 -100 -100 -100 -100
. . . . a . . . . 1 ..... 3
When the above setup finished,the item
Hovering should be set as ON and each
point of Pitch Curve should be activited at
the same time if the PlT Trim needs to be
adJusted iri flight.The points of 172M343 will
move at the same level with the up and down
of the PIT when adjusting the Hovering Trim. L1 2M3 Aifi L1 2M3 4 :1 L1 2M3 ‘ifi
(7) There are”Normal Mode". “Stunt 1“. “Stunt 2" ."Stunt 3", "Stunt 4" and “Throttle hold" 4 flight modes.The
PIT Curve can be set respectively at different models.the method of setting is as above. Press “EXT" key to
exit after finished.
The basic examples are only for your reference. Adjustment to the real flights is a must.
Throttle curve Pitch curve
100%
100%
75%
Normal flight 50.,”
25%
75%
50%
0%
Throttle curve Pitch curve
100% 100% .
l9
75% 75%
60% 70/"
+5‘
- 50% 50%
Flight mode1 50%
40%
25“,» 25%
75.
0% 0%
1. 1 2 \1 3 A H 1. 1 2 M 3 4 H
Throttle curve Pitch curve
100%
75%
50%
DEVD ’1 2E 733
cteUentlon
DEVD 12E
Welcome to use the DEVO 12E transmitter
Fitch curve
100%
75%
Autorotationlan g 50%
25%
0%
3.14 Program Mix
There are 8 series of program mix. mix channels and values are adiustable.
Setting Method:
Press ENT enter to Main Menu. Press UP or DN select function, press
ENT to enter function menu, then press UP or DN select “Program
Mix". And press ENT to Program Mix setting and current status (default
setting is “lnhibit") interface. Press R or L to choose Inhibit, Normal
or Curve.
Program Mix
Ii i i
Program Mix 1 I
Take “program mix 1" for example, there are “normal" and "curve"
setting
(t) The “normal" setting of “program mix"
Press UP or DN select the “Normal"setting, Press ENT button then pop up “All Servos Hold?“ Press R or L
to choose OK or Cancel. if
“OK" selected, all the servos
will be locked in the current
Master I
status, If Cancel selected, all All Servos Hold?
servos are unlocked. Press
ENT enter to Program mix OK Cancel Slave
setting interface.
Program Mix 1 Program Mix 1
Elevator
Master
(1.1) Master channel setting
4 Elevator
Aileron Press UP or DN to move the navigatioal mark to select Master option
and press ENT to Master interface. Press UP or UN to select the
Throttle desired channel and press ENT to make a “\"'. Press EXT to be back
Rudder to Program Mix 1 interface.
(2) Slave channel setting Slave Iiii
Press UP or DN to move the navigatioal mark to select Slave option ,/ Elevat I
and press ENT to Slave interface. Press UP or DN to select the desired _
channel and press ENT to make a “\‘". Press EXT to be back to Program Aileron
Mix1 interface. Throttle
(1.3) Gain setting: Take Elevator at Master as an example. RUddeV
Program Mix 1 (1.3.1) UP:
Up I Mix amount setting when elevator stick moved upward.
Press UP or DN to move the navigational mark to select Up to item.
Press R or L to increase or decrease, separately. the mix amount.
It is possible to reverse mix direction through changing the plus or
minus sign before amount. The adjustable range is 1125%.
Down
0%
DEVD 1 EE 7 34
oieUeniion
DEVU 1 2E
Welcome to use the DEVO 12E transmitter
(1.3.2) Down:
Mix amount setting when elevator stick moved backward. Press UP or DN to move the navigational mark to
select Down item.Press R or L to increase or decrease, separately. the mix amount. It is possible to reverse
mix direction through changing the plus or minus sign before amount. The adjustable range is i125%.
(1.3.3) Offset Setting
This function can make Slave begin to mix through the corresponding Lever SWitch from a certain point as
the starting point.
Press UP or DN select the “Offset"setting, Press R to increase the mix amount and press L to decrease It
is possible to reverse Offset direction by pressing R or l. button to change the plus or minus sign before
amount The adjustable range is 1100%.
(1.4) SWitch Selection
Press UP or DN to choose the navigation mark of Switch setting item and press ENT to enter the select
interface of Switch. It is chosen if the Switch item is marked with “V“ There are “Normal Mode", “Stunt 1".
“Stunt2","Stunt , Stunt 4"
.“Throttle hold" . ELEV DIR.
Program Mix 1 Switch u i I II
AILE D/RRUDD D/R and
GEAR which can be chosen.
Offset
0%
4 Always On I
Normal Mode
Stunt 1
Stunt 2
SWitch I
(2) Setting Method for Curve in Program Mix1
Press UP or DN to select Curve, press ENT to confirm. Then the interface pop up "All Servos Hold7“. press
R or Lto choose OK or Cancel.
If select OK. all the servos Will Program Mix 1 [I‘ll Program M)” ”ll“
be lockegin the‘ current status, Master ,9 . .2 I
i se ect ance, a servos are
unlocked. Press ENT to setting A“ Servos ”Old?
interface of program Mix1. OK Cancel Slave
Elevator timid;
Master E i i H (2.1) Master channel setting
4 Elevator
Press UP or DN to move the navigatioal mark to select Master option
Ailei’on and press ENT to Master interface. Press UP or DN to select the
Throttle desired channel and press ENT to make a “xi". Press EXT to be back
Rudder to Program Mix 1 interface.
22 Si n i n Slave ”H”
. ave C anne se in
( ) g 4 Elevator
Press UP or DN to move the navigatioal mark to select Slave option _
and press ENT to Slave interface. Press UP or DN to select the desired Aileron
channel and press ENT to make a “V‘” Press EXT to be back to Program Throttle
Mix1 interface. Rudder
(2.3) Exponential Curve
Press UP or DN to choose the setting item of "Exponential" .There are On or Off option when you press the
R or L buttoms. Select On for smooth changes, and Off for changes in the form of fold ling in Exponential
curve, respectively.
DEVD 1 EE 735
JeUeniion
Welcome to use the DEVO 12E transmitter
DEVD 12E
(2.4) Point Setting
Press UP or DN to move the navigation mark of Point option Press
R or L, there are 7 piont options including "PointrL". "Point ' '
2", "Point-M", "Point-3", "Pomt -4" and "Point-H". Select the point you
want to set.
Program Mix 1
Point
Point , 1
Status
Program Mix 1
Exponential
Off
Point
(There is no Status options when the piont is Point-L or Point-H) After
selecting the point that you want to set. press UP or DN to move the
navigational mark to Status item. Press R or L, there are two options
oi Inhibit and Active. Select Inhibit for unchanging the current amount
ti 2mm
(2.5) Status Setting
(2.6) output setting
'Ei' iivijiifi (the default setting is Inhibit).
When the Status option is Active. the Output option will be |isted.Press
UP or UN to move the navigational mark to Output. Press R or L to
increase or decrease, respectively, the output amount. It is possible
to reverse the mix direction by changing the plus or minus sign before
the amount. The adiustable range is :100%.
(2.7) SWitch select
Program Mix 1 Dilll
Output .9 . ~9i
Switch
0“ ti mm I
Press UP or DN to choose the navigation mark of Switch setting item and press ENT to enter the select
interface of Switch. It is chosen if the Switch item is marked with “V“ There are “Normal Mode", “Stunt 1",
“Stunt 2". "Stunt 3". "Stunt 4"
,“Throttle hold", "ELEV DIR", ng'a’" Mix 1 SW“ iIII
"AILE DIR", "RUDD DR" and Output 9- -‘% 4 A'Ways 0" I
"GEAR" which can be chosen. 0% Normal Mode
Press EXT key to return to the SWitch Stunt 1
previous interface for other
settings or press EXT key to it midi I
Stunt 2
exit after finished.
3.15 Monitor
This function can display the current status and positions of all the channels’ outputs, and check the current
working status of each channel.
Press ENT to enter Main Menu. and then press UP or DN to move
the navigational mark to select Function Menu.Press ENT to enter
the Function Menu and then press UP or DN to select servo Monitor
and press ENT to enter the monitor interface for checking the current
working status of each channel
Press EXT to exit .
3.16 Fail safe
Monitor
There are two possibilities for use if the transmission signal is under abnormal condition. The first one is to
lock the last action data received; the second one is to execute the preset data which is preeset The default
setting is Servo Hold.
Setting method:
Press ENT to enter the Main Menu. and then press UP or DN to move
the navigational mark to select Function Menu Press ENT to enter
the Function Menu then press UP or DN to select Fail Safe and press
ENT to enter the Fail Safe interfaceTake the item Elevator as an
example to explain.
DEVO 1 QE 7 BE
Fail Safe
Elevator

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 10
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2014:04:15 15:21:17
Modify Date                     : 2014:04:15 15:21:17
Title                           : DEVO-12E manual 1.pdf
Creator                         : PScript5.dll Version 5.2.2
Author                          : Frank
EXIF Metadata provided by EXIF.tools
FCC ID Filing: S29DEVO12E

Navigation menu