GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual

GuangZhou Walkera Technology Co., Ltd 2.4GHz Transmitter DEVO 12E manual

Users Manual part 10 of 11

Download: GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual
Mirror Download [FCC.gov]GuangZhou Walkera Technology DEVO12E 2.4GHz Transmitter User Manual DEVO 12E manual
Document ID2246015
Application IDvhhzY35Of3si6HJEbqniHA==
Document DescriptionUsers Manual part 10 of 11
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize374kB (4675043 bits)
Date Submitted2014-04-18 00:00:00
Date Available2014-04-18 00:00:00
Creation Date2014-04-15 15:26:37
Producing SoftwareGPL Ghostscript 8.15
Document Lastmod2014-04-15 15:29:55
Document TitleDEVO-12E manual.PDF
Document CreatorPScript5.dll Version 5.2.2
Document Author: Frank

oleUention
Welcome to use the DEVO 12E transmitter
DEVD 1 BE
(4) EXp°"e""al Dual Rate and EX... uj|||
Press UP or UN to move the navigation mark to select Exponential. Dual Rate r
It’s possible to change Dual Rate and Exponential value in Pos when 100"/ ‘ I
pressing R or L to change the value. There are+ 100% and Line ° .
three adjustment. At the same time, the corresponding curve Will be Exponential
changed and shown at the right graph. 4
(5) Automatic setting
Under working with Flight Mode, it's possible to sWitch the Dual Rate and Exponential, which are set in
above"(3) Dual Rate adjustment" and "(4) Exponential adjustment", respectively.
_ The setttings for Cruise Mode, Speed Mode, Thermal Mode,
—— ‘ . Flight M09“? Launch Mode and Land Mode 5 are available.
‘. I - Note: If want to use this function, it is necessary to previously
a ,‘ set both "Flight Speed Switch" and "Flight Launch Switch" at
— Device Select in Model Menu as the corresponding switches.
a .. - ..
Refer to 2.9 DeVIce Select .
- e -
(5.1) Cruise Mode setting:
Press UP or DN in the navigation mark of Dual Rate and Exponential Dual Rate and EX'”
to select the desired item Cruise Mode. Press R or L to set the position Cruise Mode
and the Switch. Only the D/R switch control is valid When Switch is m
selected, under the Flight Mode, it's possible for Pos to SWitch the
Dual Rate and Exponential, which are set in above(3) and (4)Exponential Speed Mode
adjustment. The settings for vatich. P050. Pos1. Pos2 . Pos3. P054 SWitch
are valid.
(5.2) The setting for Speed Mode, Thermal Mode. Launch Mode, Land Mode can be set up according to above
Cruise Mode Setting. Press EXT to exit after finishing the setting.
3.5 Motor Hold
The Motor Hold can be switched after the function is used. The setting range of Motor Hold is from -10% to
100%. The item Motor should be previously set at Device Output in Model Menu. which is used as Spoiler
Stick and is activated. Refer to "2.10 Device Output".
Motor Hold
Setting method:
Press ENT to enter Main Menu; Press UP or DN to move the navigation Hold Position
mark to Function Menu. and press ENT to enter Function Menu. Press
UP or DN to choose Motor Hold and Press ENT to enter Motor Hold .
. SWitch
interface.
Off
(1) Hold Position
In the Motor Hold interface, press UP or DN to move the Navigation mark to choose “Hold Position" setting
options. Press R or L to increase or decrease the amount respectively The adjustable range is from 40.0%
to 100.0% and the default setting is 0.0%.
(2) Switch Selection
Press UP or DN to choose the naVigation mark of SWitch setting item and press ENT to enter the select
interface of Switch. Press UP
or DN to select the switch you w SWlmh D ‘ I H
want and a “\l , will be shown Hold Position m
in its left. If two or more 00% Cruise Mode
SWitches are chosen. the item
"And" should be selected. SWitCh Speed Mode
Press EXT to exit atter setting “ Thermal Mode
up finished.
DEVD ‘1 EE 7&7
JeUention
DEVO 1 2E Welcome to use the DEVO 12E transmitter
3.6 Flaperon Mix
This function is used to Mix Aileron to Flaperon. or Mix Elevator to Flaperon. The Mix amount can be
independently set in each flight mode.
The Flap Rate in each flight mode should be previously set before using this function Refer to the following
"3.16 Flap Rate".
. Flaperon Mix :iiii
Setting method: —
Press ENT to enter Main Menu; Press UP or DN to move the navigation Flap Lever Offset I
mark to Function Menu. and press ENT to enter Function Menu. Press
UP or DN to choose Flaperon Mix and Press ENT to enter Flaperon .
. . . . _ Flight Mode
MIX interface. Picture as right.
Cruise Mode
(1) Flap Lever Offset setting
This function can be used to set the neutral points of Flaperon servos.
Press UP or DN to move the Navigation mark to choose “Flap Lever Offset" setting options. Press R or l. to
increase or decrease the amount respectively. The adjustable range is t‘lOO‘Vn. It is possible to change the
offset direction by changing the plus or minus sign before the amount.
(2) Flight Mode setting Flaperon Mix ul|||
The flight mode should be preViously activated in "Device Select" Flap Lever Ofise‘ I
before using this function (Refer to "2.9 Device Select"). 0%
Flight Mode
Press UP or DN to move the NaVigation mark to select “Flight Mode"
setting options. press R or L to select the desired item.
Cr
9M0
(3) Flap to Flaperon setting
Flaperon Mix [W Press DN to display Flap to Flaperon setting interface. and press UP
or DN to move the Navigation mark to choose “UP or Down" setting
F‘aP ‘0 Flaperon options. Press R or L to change the Flaperon Mix value when moving
UP I the Flaperon stick. The bigger the Value is. the bigger Mix Will be .
The adjustable Mix is ranged from 425% to +125%. It is possible to
Down 0% change the Flaperon Mix direction by changing the plus or minus sign
before the value
(A) Flap to Elevator setting
Press DN to display Flap to Elevator setting interface. and press UP Flaperon Mix
or DN to move the Navigation mark to choose “UP or Down" setting
options. Press R or L to change the Elevator Mix value when moving Flap to Elevator
the Flaperon stick. The bigger the Value is. the bigger Mix will be. UP “
The adjustable Mix is ranged from 425% to +125%. It is possible to
change the Elevator Mix direction by changing the plus or minus sign 0%
before the value.
Press EXT to exit after finishing the setting.
3.7 Camber System
This function can change the Aileron angel. which goes through the central line of the main wings' transect.
and then change the features of main wings.
Setting method: Camber System DH“
Press ENT to enter Main Menu; Press UP or UN to move the navigation Flight Mode I
mark to Function Menu. and press ENT to enter Function Menu. Press
UP or DN to choose Camber System and Press ENT to enter Camber
System interface. Picture as right:
DEVC} 1 EE 7 BE
oleUention
DEVD 1 2E
Welcome to use the DEVO 12E transmitter
(1) Flap Lever Offset setting
The flight mode Should be previously activated in "Device Select" before using this function (Refer to "2.9
Device Select").
Press UP or DN to move the Navigation mark to select “Flight Mode" setting options, press R or L to select
the desired item.
(2) L-Aileron/ R-Aileron setting Camber System
Press UP or DN to move the Navigation mark to choose “L-Aileron L’Aileron
or R-Aileron" setting options. Press R or L to change the position of
L’Aileron or RrAileron With a range of :100%. It is possible to alter “
the direction of L-Aileron or R-Aileron via changing the letter of "R" .
.. .. R-Aileron
or L before the amount. 0%
Press EXT to exit afler finishing the setting.
3.3 Differential
The flight mode should be previously activated in "Device Select" before using this function (Refer to "2.9
Device Select").
Differential
Flight Mode Press ENT to enter Main Menu; Press UP or DN to move the navigation
mark to Function Menu. and press ENT to enter Function Menu. Press
UP or DN to choose Differential and Press ENT to enter Differential
Aileron interface. Picture as left:
(1) Flight Mode setting
Press UP 0r DN to make the Navigation mark to select “Flight Mode" setting options. press R or L to select
the desired item.
(2) Aileron differential setting
Differential
It is possible to decrease the vibration to the head from reverse
direction in operating aileron.
Flight Mode
Press UP or DN to move the Navigation mark to select “Aileron" setting Cruise Mode
options. press R or L to increase or decrease. respectively. the value
with a range of :100%.
Aileron
Differential (3) Brake differential setting
lf co-working with the spoiler stick. the brake differential function can
counteract the differential.
Brake Differential Press UP or DN to move the Navigation mark to select “Brake" setting
0% options. press R or L to increase or decrease. respectively. the value
With a range from 0% to 100%.
Press EXT to exit after finishing the setting.
3.9 Balance
This function can adiust the two-servo parameters. which are simultaneously used in dual output channels.
but "Dual Channels" should be previously activated at Wing Type in Model Menu (Refer to " 2.11 Wing Type").
Setting method: Balance DH“
Press ENT to enter Main Menu; Press UP or DN to move the navigation Channel I
mark to Function Menu. and press ENT to enter Function Menu. Press
UP or DN to choose Balance and Press ENT to enter Balance interface.
Picture as right:
DEVC} 1 EE 7 BE
oleUenlion
DEVD 1 2E
Welcome to use the DEVO 12E transmitter
(1) Channel: current setting channel is Aileron. System default can not be set.
Balance W (2) Point parameter adjustment
pojm < Rjgm i Point< Right Setting: Press UP or DN to choose “Point< Right". if
need to adjust the value, press L (0% means no adjusting). A minus
value means the amending direction is downward; press R to adjust
value(0% means no adjusting). A plus value means the amending
direction is upward. The adjustable range is L 100%.
PointrRight Setting: Press UP or DN to choose “PointeRight‘K Press R or L to Inhibit or Active. If need to adjust
please Active it. There will be expanded value adjustment item. Press UP or DN to choose “0%" It need to
adjust the value, press L (0% means no adjusting). A minus value means the amending direction is downward;
press R to adjust value (0%
. . B | B i
means no adjusting). A plus aance [W aance [W
value means the amending Point- Right Point- Right
direction is upward. The I I
Active
adjustable range is 100%. m
Press UP or DN, there will be setting for Point-1, Point-2, Point-3, Point-Left, Point>Left, refer to the setting
method as above. Press EXT after finished it.
3.10 Gyro Sensor
This function offers the gain adjustment for gyro sensor It is possible to be automatically switched among
various gains via tlight mode, which should be previously set at Device Select in Modei Menu (Refer to "2.9
Device Select"), and the gyro output should also be simultaneously set at Device Output (Refer to "2 10 DeVice
Output").
Gyro Sensor
Mode I
Channel
Press ENT to enter Main Menu; Press UP or DN to move the navigation
mark to Function Menu, and press ENT to enter Function Menu. Press
UP or DN to choose Gyro Sensor and Press ENT to enter Gyro Sensor
interface. Picture as right:
Motor
(1) Mode: System default mode is Automatic.
(2) Channel: The displaying is the sensitivity channel of Gyro. Refer to "2.10 Device Output" to select.
(3) Switch: System default can not be set.
(4) Status:
Turn the Flight Mode Switch, the status display present flight mode position There are “Cruise Mode".“Speed
Mode",“Thermal Mode", "Launch Mode", "Land Mode“ sets.
5) Cruise Mode'
Press UP or DN to select Cruise Mode, press R or L can increase or
Gyro Sensor
decrease the value individually. If the gyro used has two modes of Status
NOR and AVCS, NOR Will be activated when the value is less than Cruise Mode
50.0%. In NOR mode, the smaller the value is, the bigger the gyro Cruise Mode
sensor sensitivity will be; In AVCS Mode, the bigger the value is, the
bigger the gyro sensor sensitivity Will be. The factory setting is 50.0%.
(6) "Speed Mode", "Thermal Mode", "Launch Mode", "Land Mode" 4 settings refer to “Cruise Mode".
After finishing the set, press EXT to exit.
DEVD ‘l BE 790
oleUenlion
DEVD 1 EE
Welcome to use the DEVO 12E transmitter
3.11 Rudder to Spoiler Mix
When this function is activated, the spoiler can be used as Rudder in the models Without Rudder and can
also be mixed. The mix gain can be independently set in each flight mode, which should be preViously set
at Device Select in Model Menu (Refer to "2.9 Device Select“), and "Dual Spoilers" should also be activated
at Wing Type (Refer to "2.11 Wing Type").
Rudder to Spoiler...
Setting method:
Cruise Mode
Speed Mode
0.0%
Press ENT to enter Main Menu; Press UP or DN to move the navigation
mark to Function Menu, and press ENT to enter Function Menu. Press
UP or DN to choose Rudder to Spoiler Mix and Press ENT to enter
Rudder to Spoiler Mix interface. Picture as right:
There are five flight modes: Cruise Mode, Speed Mode, Thermal Mode, Launch Mode, Land Mode. Press
UP or DN to move the navigation mark to select the desired flight mode. Press R or L to increase or decrease
amount respectively. The adjustable range is from 0.0% to 100.0% and the default setting is 0.0%.
After finishing the set, press EXT to exit.
3.12 Aileron to Rudder Mix
This function aims at mixing the rudder when operating the aileron. The mix value can be respectively set in
each flight mode. But the flight mode should be preViously set at Device Select in Model Menu (Refer to "2.9
Device Select“).
Aileron to Rudder...
Setting method:
Elevator Stick
Press ENT to enter Main Menu; Press UP or UN to move the navigation
mark to Function Menu, and press ENT to enter Function Menu. Press
UP or DN to choose Aileron to Rudder Mix and Press ENT to enter
Aileron to Rudder Mix interface. Picture as right:
Rudder Stick
Inhibit
(1) Elevator Stick setting
This function is that: if the elevator stick position is set at one point. this point will become the cut-off point
whether to mix. when the elevator stick is moved down from this point, the mix will be cancelled; While the
elevator stick is moved up from this point, the mix will be activated.
Press UP or DN to move the Navigation mark to select "Elevator Stick" setting options, press R or L to increase
or decrease, respectively, the value with a range of D1%-100%. When the elevator stick is moved down from
the set value, the mix will be cancelled; while the elevator stick up from this value, the mix will be activated.
The default setting is Inhibit.
(2) Rudder Stick setting
The setting is same as above. The adjustable rang is from L/R1% to L/R100%. and the factory setting is Inhibit.
(3) Mix value setting for each flight mode
There are total five flight modes. The flight mode should be previously set at Device Select in Mode Menu
(Refer to "2.9 Device Select").
Aileron to Rudder... :iiii
+ Press UP or UN to move the Navigation mark to select the desired
CFU'Se M°de flight mode of "Left" setting options. Press R or L to change Rudder
Left m I mix value when moving the aileron stick leftward. It is possible to
change the mix direction via changing the plus or minus sign before
Right 0% the value. The adjustable mix is 1125%.
Press UP or DN to move the Navigation mark to select the desired flight mode of "Right" setting options.
Press R or L to change Rudder mix Valuer when moving the aileron stick rightward. It is possible to change
the mix direction via changing the plus or minus sign before the value. The adjustable mix is :125%. After
finishing the set, press EXT to exit.
DEVD 1 EE 791
oleUention
DEVD 1 2E Welcome to use the DEVO i2E transmitter
3.13 Elevator to Flap Mix
This function aims at mixing flap when operating elevator stick. It can be respectively set in each flight mode,
which should be previously set at Device Select in Mode Menu (Refer to "2.9 Device Select”).
Setting method: Elevator to Flap...
Press ENT to enter Main Menu; Press UP or UN to move the navigation Cruise Mode I
mark to Function Menu, and press ENT to enter Function Menu. Press up “
UP or DN to choose Elevator to Flap Mix and Press ENT to enter
Elevator to Flap Mix interface Picture as right' DOW" 0%
Offset 0%
(i)Cruise Mode
(1.1)UPsetting
Press UP or DN to move the Navigation mark to select "UP" setting options in the Cruise Mode. Press R or
L to change Flap mix value when moving the Elevator stick upward. It is possible to change the mix direction
Via changing the plus or minus sign before the value. The adjustable mix is 1125%.
(1.2) Down setting
Press UP or DN to move the Navigation mark to select "Down" setting options in the Cruise Mode. Press R
or L to change Flap mix value when moving the Elevator stick downward. It is possible to change the mix
direction via changing the plus or minus sign before the value. The adjustable mix is :125%.
(i .2) Offset setting
Press UP or DN to move the NaVigation mark to select "Offset" setting options in the Cruise Mode. Press R
or L to amend the central point of flap servo. The bigger the value is, the bigger the offset will be. It is possible
to change the offset direction via changing the plus or minus sign before the value. The adjustable offset
range is :100%.
(2) “Speed Mode", "Thermal Mode", "Launch Mode". “Land Mode" 4 settings refer to “(1) Cruise Mode”.
After finishing the set, press EXT to exit.
3.14Aileron to Flap Mix
This function aims at mixing flap when operating aileron stick. it can be respectively set in each flight mode.
But the flight mode should be previously set at Device Select in Mode Menu (Refer to "2.9 Device Select"),
and the flap dual channels should also be previously activated at Wing Type in Mode Menu (Refer to "2.11
Wing Type")
Setting method' Aileron to Flap Mix nl|l|
Press ENT to enter Main Menu; Press UP or DN to move the navigation cmlse Mode I
mark to Function Menu. and press ENT to enter Function Menu. Press Left m
UP or DN to choose Aileron to Flap Mix and Press ENT to enterAileron
to Flap Mix interface. Picture as right: Right 0%
(i) Cruise Mode
(1.1) Leftsetting
Press UP or DN to move the Navigation mark to select "Left" setting options in the Cruise Mode. Press R or
L to change Flap mix value when moving the Aileron stick leftward. It is possible to change the mix direction
Via changing the plus or minus sign before the value. The adjustable mix is :i25%.
(i .2) Right setting
Press UP or UN to move the Navigation mark to select "Right" setting options in the Cruise Mode. Press R
or L to change Flap mix value when moving the Aileron stick rightward. It is possible to change the mix direction
Via changing the plus or minus sign before the value. The adjustable mix is :i25%.
(2) "Speed Mode", "Thermal Mode' "Launch Mode", "Land Mode" 4 settings refer to “(i) Cruise Mode”.
After finishing the set, press EXT to exit.
DEVD 1 EE 7 BE
oleUenfion
DEVD 1 EE
Welcome to use the DEVO 12E transmitter
3.15 Aileron to Tip-Aileron Mix
This function aims at mixing Tip-Aileron when operating Flap. it can be respectively set in each flight mode.
But the flight mode should be previously set at Device Select in Mode Menu (Refer to "2.9 Device Select"),
and the Tip-Aileron should also be activated at Wing Type in Mode Menu (Refer to "2.11 Wing Type").
Setting method: Aileron to Tip Ail... nj|j|
Press ENT to enter Main Menu; Press UP or DN to move the nawgation Cruise Mode
mark to Function Menu, and press ENT to enter Function Menu. Press Left ”00%
UP or UN to choose Aileron to Tip Aileron Mix and Press ENT to enter
Aileron to Tip Aileron Mix interface. Picture as right: Right ”00%
(1) Cruise Mode
(1.1) Leftsetting
Press UP or DN to move the Navigation mark to select "Left" setting options in the Cruise Mode. Press R or
L to change the Tip Aileron mix value when moVing the Aileron stick leftward. It is possible to change the
mix direction Via changing the plus or minus sign before the value. The adjustable mix is 212570. The default
setting is 100%.
(1 .2) Right setting
Press UP or DN to move the Navigation mark to select "Riht" setting options in the Cruise Mode. Press R
or L to change the Tip Aileron mix value when moving the Aileron stick rightward. It is possible to change
the mix direction Via changing the plus or minus sign before the value. The adjustable mix is t125%. The
default setting is 100%.
(2) "Speed Mode", "Thermal Mode", "Launch Mode". "Land Mode" 4 settings refer to “(1 ) Cruise Mode“.
After finishing the set, press EXT to exit.
3.16 Flap Rate
This function can set the Flap Rate in all the flight modes. 0% is set the neutral center of Flap angle. It is
possible to set the Flap Rate of either upward or downward direction. There are total five flight modes, each
one of which should be preViously set at Device Select in Mode Menu (Refer to "2.9 DeVice Select“).
Setting method: Flap Rate llll
Press ENT to enter Main Menu; Press UP or DN to move the navigation Cruise Mode I
mark to Function Menu, and press ENT to enter Function Menu. Press .
UP or DN to choose Flap Rate and Press ENT to enter Flap Rate Up +1005
interface Picture as right'
+100%
(1)0ruise Mode
(1.1) Up setting
Press UP or DN to move the Navigation mark to select "Up" setting options in the Cruise Mode. Press R or
L to change the Flap Rate when Flap moving upward. It is possible to change the direction by changing the
plus or minus sign before the value. The adjustable mix is :125%. The default setting is 100%.
(1.2) Up setting
Press UP or DN to move the Navigation mark to select "Down" setting options in the Cruise Mode. Press R
or L to change the Flap Rate when Flap movmg downward. it is possible to change the direction by changing
the plus or minus sign before the value. The adjustable mix is t125%. The default setting is 100%.
(2) "Speed Mode", "Thermal Mode' "Launch Mode", "Land Mode" 4 settings refer to “(1) Cruise Mode”.
After finishing the set, press EXT to exit.
DEVCJ 1 EE 7 93
oleUenlion
DEVD 1 2E Welcome to use the DEVO 12E transmitter
3.17 Brake System
Through the spoiler stick operation, all the actions caused by mobile Wings in main wings Will be turned into
the mix which aims at brake. It can be switched between Pos 0 and Pos 1 Via setting the item sWitch.
Setting method: Brake System um.
Press ENT to enter Main Menu; Press UP or DN to move the navigation Spoiler Silek I
mark to Function Menu. and press ENT to enter Function Menu. Press
UP or UN to choose Brake System and Press ENT to enter Brake
System interface. Picture as right: Switch
Pos 0
(1) Spoiler stick setting
When the spoiler stick is set at one certain point. this point Will become the cut-off point Whether to brak
The mixing Will be working when the spoiler stick is being moved to this point from down to up.
Press UP or DN to move the NaVigation mark to select "Spoiler Stick" setting options. The spoiler stick position
will be set through pressing R or L to change the value. The adjustable range is from 0.0% to 100.0% and
the default value is 100.0%.
(2) Switch Selection
Press UP or DN to move the NaVigation mark to select "Switch“. Press ENT to enter Switch interface, press
UP or DN to choose desired switch item. Press ENT to confirm. the desired switch item Whose left side will
be changed into “1" from “"0.
If two or more items are w SWitch 5"“
selected, the item And should Spoiler Stick I
be selected, whose left side 100.0% © Cruise Mode
should be changed into 1 _
from ““0. Press EXT after SW'lCh © Speed Mode
finished it.
© Thermal Mode
(3) Brake to Spoiler setting
Press UP or DN to move the Navigation mark to select "Pos 0" in the Brake to Spoiler setting interface. The
brake mix at Post) Will be altered through pressing R or L to change the value. The adjustable value is 0.0-
100.0%, and the default setting is 100.0%
Brake System z i i ii
Spoiler Press UP or DN to move the Navigation mark to select "Pos 1" in
n I the Brake to Spoiler setting interface. The brake mix at Pos1 will be
P05 0 10 A altered through pressing R or L to change the value. The adjustable
value is 0.0-100.0%, and the default setting is 100.0%
P05 1 100.0%
(4) Brake to Flaperon setting
The setting is same as above. It is possible to change the mix direction through changing the plus or minus
sign before the value. The adjustable value is 1125%, and the default setting is 0%.
(5) Brake to Elevator: The setting is same as above.
(6) Brake to Flap: The setting is same as above.
(7) Brake to Tip Aileron: The setting is same as above.
After finishing the set, press EXT to exit.
DEVD 1 EE 7 B4
oleUenlion
Welcome to use the DEVO 12E transmitter
DEVD 1 ea
3.13 Program mix
There are 8 series of program mix, mix channels and values are adjustable.
Setting Method:
Press ENT enter to Main Menu. Press UP or DN select function. press Program Mix Ellll
ENT to enter function menu, then press UP or DN select “Program Pro ram Mix 1
Mix". And press ENT to program Mix setting and current status (default 9 I
setting is “lnhibit") interface. Press R or L to choose Inhibit, Normal
or Curve.
Take “program mix 1" for example, there are “Normal" and “Curve"
setting.
(1) The “Normal" setting of "program mix"
Press UP or DN select the “Normal" setting, Press ENT button then pop up “All Servos Hold?" Press R or L
to choose OK or Cancel. If
“OK" selected, all the servos Program Mix 1 ul||l Program Mix 1 Ellll
will be locked in the current Master I
status, if “Cancel" selected, all All Servos Hold? m
servos are unlocked. Press
ENT enter to Program mix OK Cancel Slave
setting interface. Elevator
Master :llll (1.1) Master channel setting
4 Elevator
Aileron Press UP or DN to move the navigatioal mark to select Master option
and press ENT to Master interface. Press UP or DN to select the
Flaperon desired channel and press ENT to make a “v‘. Press EXT to be back
Rudder to Program Mix 1 interface.
(2) Slave channel setting Slave Em,
Press UP or DN to move the navigatioal mark to select Slave option .1 Elevator
and press ENT to Slave interface. Press UP or UN to select the desired
channel and press ENT to make a "v’". Press EXT to be back to Program Aileron
Mix1 interface. Flaperon
(1.3) Gain setting: Take Elevator at Master as an example. RUddEV
Program Mix 1 (1.3.1) Pos 0 UP:
Pos 0 Up Mix amount setting when elevator stick moved upward.
Press UP or DN to move the navigational mark to select "Pos 0 Up"
item. Press R or L to increase or decrease, separately, the mix
P05 0 Down 00/ amount. It is poSSible to change the mix direction through changing
the plus or minus sign before amount. The adjustable range is :125%.
(1.3.2) Pos 0 Down:
Mix amount setting when elevator slick moved downward.
Press UP or UN to move the navigational mark to select "Pos 0 Down" item. Press R or L to increase or
decrease, separately, the mix amount. It is possible to change the mix direction through changing the plus
or minus sign before amount. The adjustable range is :125%.
(1.3.3) Pos 1 Up, Pos 1 Down setting method refer to (1.3.1) Pos 0 Up setting.
(1.3.4) Offset Setting
This function can make Slave begin to mix through the corresponding Lever sWitch from a certain point as
the starting point.
DEVD 1 2E 795

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-702
Create Date                     : 2014:04:15 15:26:37Z
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2014:04:15 15:29:55+08:00
Metadata Date                   : 2014:04:15 15:29:55+08:00
Format                          : application/pdf
Creator                         : Frank
Title                           : DEVO-12E manual.PDF
Producer                        : GPL Ghostscript 8.15
Document ID                     : uuid:2a1ff8ca-1b14-4659-aeaf-2b090384c44d
Instance ID                     : uuid:823665d4-0820-4d62-b0b7-fbaf3b85f27f
Has XFA                         : No
Page Count                      : 9
Author                          : Frank
EXIF Metadata provided by EXIF.tools
FCC ID Filing: S29DEVO12E

Navigation menu